DVD Home Theater Sound System
Transcription
ORDER NO. MD0705010CE DVD Home Theater Sound System SA-PT150GC SA-PT150GCP SA-PT150GCS SA-PT150GCT SA-PT150GS Colour (S).......................Silver Type Specifications lGENERAL Power Supply: Power Consumption: AC 110 to 240 V, 50/60 Hz Main unit 105 W Power Consumption in Standby Mode: approx. 1 W lFront Ch: 25 W / Channel (5 Ω) lCenter Ch: 25 W / Channel (5 Ω) lSurround Ch: 25 W / Channel (5 Ω) At 100 Hz and total harmonic of 1% lSubwoofer Ch: Dimensions (W×H×D): 430×60×342 mm lFM TUNER, TERMINALS SECTION Mass: Main unit 3 kg Preset Memory: Operating Temperature Range: +5°C to +35°C Frequency Modulation (FM) Operating Humidity Range: 5% to 90% RH (no condensation) lAMPLIFIER SECTION RMS Output Power: Dolby Digital Mode lTotal RMS Dolby Digital mode power: 330 W At 1 kHz and total harmonic of 10% Frequency range: 1.8 µV (IHF) S/N 26 dB: 1.4 µV Antenna terminals: 75 Ω (unbalanced) Mic Jack: Sensitivity: 0.7 mV (1.2 kΩ) Terminal: Mono, 6.3 mm jack (1 system) lCenter Ch: 55 W / Channel (5 Ω) lUSB SECTION lSurround Ch: 55 W / Channel (5 Ω) USB Port: PMPO Output Power: 55 W / Channel (5 Ω) 2800 W DIN Output Power: Dolby Digital Mode: lTotal DIN Dolby Digital mode power: 87.50-108.00 MHz (50-kHz step) 55 W / Channel (5 Ω) lSubwoofer Ch: FM 30 stations Sensitivity: lFront Ch: At 100 Hz and total harmonic of 10% 25 W / Channel (5 Ω) USB standard: USB 2.0 full speed Media file format support: MP3 (*.mp3) WMA (*.wma) JPEG (*.Jpg, *.JPEG) MPEG4 (*.asf) 150 W At 1 kHz and total harmonic of 1% © 2007 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS USB device file system: FAT12 FAT16 FAT32 USB Port power: 500 mA (Max) lTerminal: Pin jack (Y: green, PB: blue, PR: red) (1 system) Note: 1. Specifications are subject to change without notice. lDISC SECTION Mass and dimensions are approximate. Discs played (8 cm or 12 cm): 2. Total harmonic distortion is measured by the digital spectrum analyzer. (1) DVD [DVD-Video, DivX (*1, *2)] (2) DVD-RAM [DVD-VR, MP3 (*2, *6), JPEG (*2, *3), MPEG4 (*2, *4), DivX (*1, *2)] Solder: (3) DVD-R [DVD-Video, DVD-VR, MP3 (*2, *6), JPEG (*2, *3), MPEG4 (*2, *4), DivX (*1, *2)] Mechanism: (4) DVD-R DL [DVD-Video, DVD-VR] (5) DVD-RW [DVD-Video, DVD-VR, MP3 (*2, *6), JPEG (*2, *3), MPEG4 (*2, *4), DivX (*1, *2)] (6) +R/+RW [Video] (7) +R DL [Video] (8) CD, CD-R/RW [CD-DA, Video CD, SVCD (*5), MP3 (*2, *6), WMA (*2, *7), JPEG (*2, *3), MPEG4 (*2, *4), DivX (*1, *2)] This model uses lead free solder (PbF). This model uses DL2S (Single tray) mechanism. Power Supply: This unit uses Switching Mode Power Supply (SMPS). *1 Plays all versions of DivX® video (including DivX®6) with standard playback of DivX® media files. Certified to the DivX Home Theater Profile. *2 The total combined maximum number of recognizable audio, picture and video contents and groups: 4000 audio, picture and video contents and 400 groups. *3 Exif Ver 2.1 JPEG Baseline files lPicture resolution: between 160 x 120 and 6144 x 4096 pixels (Sub sampling is 4:0:0, 4:2:0, 4:2:2, or 4:4:4). Extremely long and narrow pictures may not be displayed. *4 MPEG4 data recorded with the Panasonic SD multi cameras or DVD video recorders. Refer to their respective original service manuals for *1, *2, *3, *4. lConforming to SD VIDEO specifications (ASF standard)/ MPEG4 (Simple Profile) video system/G.726 audio system. *5 Conforming to IEC62107 *6 MPEG-1 Layer 3, MPEG-2 Layer 3 *7 Windows Media Audio Ver.9.0 L3 lNot compatible with Multiple Bit Rate (MBR) Pick Up: Wavelength: lCD: 785 nm lDVD: 662 nm Laser power: lCD: CLASS 1M lDVD: CLASS 1 Audio Output (Disc): Number of channels: 5.1 ch (FL, FR, C, SL, SR, SW) lVIDEO SECTION Video system:( GC/GCS/GCT/GS) PAL 625/50, PAL 525/60, NTSC Video system: (GCP) NTSC Composite Video Output: lOutput level: 1 Vp-p (75 Ω) lTerminal: Pin jack (1 system) Component video output: [NTSC: 480p/480i, PAL:576p/576i] lY output level: 1 Vp-p (75 Ω) lPB output level: 0.7 Vp-p (75 Ω) lPR output level: 0.7 Vp-p (75 Ω) 2 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS CONTENTS Page 1 Safety Precautions 1.1. GENERAL GUIDELINES Page 5 1.2. Before Repair and Adjustment (Using SMPS Module 5 P.C.B.) 1.3. Protection Circuitry 3 5 5 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 1.4. Safety Parts Information 6 11.3. Checking & Repairing Main P.C.B. 50 1.5. Caution for AC Cord 7 11.4. Checking & Repairing SMPS Module P.C.B. 51 11.5. Checking & Repairing DVD Module P.C.B. 51 2 Prevention of Electro Static Discharge (ESD) to 8 Electrostatically Sensitive (ES) Devices 3 Precaution of Laser Diode 4 About Lead Free Solder (PbF) 4.1. Service caution based on legal restrictions 5 Handling Precautions for Traverse Unit 12 Measurements and Adjustments 52 9 12.1. Service Tools and Equipment 52 10 12.2. Important points in adjustment 52 10 12.3. Storing and handling of test discs 52 11 12.4. Optical adjustment 53 13 Abbreviations 54 11 14 Voltage and Waveform Chart 56 11 14.1. DVD Module P.C.B. 56 6 Accessories 13 14.2. Main P.C.B. 58 7 Operation Procedures 14 14.3. Panel P.C.B. 59 7.1. Remote Control Key Buttons Operations 14 14.4. Tray Loading & SMPS Module P.C.B. 59 7.2. Main Unit Key Buttons Operations 15 14.5. Waveform Chart 60 7.3. About DivX VOD Content 16 15 Illustration of IC's, Transistors and Diodes 62 7.4. USB Connection and Operation 17 16 Wiring Connection Diagram 63 7.5. Audio and Video Connections 18 17 Block Diagram 65 7.6. Disc Information 20 17.1. System Control 65 22 17.2. DVD (Servo) 66 8.1. Service Mode Summary Table 22 17.3. DVD (Audio) 67 8.2. Service Mode Table 22 17.4. DVD (Video) 68 8.3. DVD Self Diagnostic Function-Error Code 30 17.5. Audio 69 8.4. Sales Demonstration Lock Function 33 17.6. Amp & Power 70 8.5. Service Precautions 34 18 Schematic Diagram Notes 71 35 19 Schematic Diagram 73 5.1. Cautions to Be Taken in Handling the Optical Pickup Unit 5.2. Grounding for electrostatic breakdown prevention 8 Self-Diagnosis and Special Mode Setting 9 Assembling and Disassembling 9.1. Disassembly Flow Chart 36 19.1. DVD Module Circuit 73 9.2. Main Components and P.C.B. Locations 37 19.2. Main Circuit 77 9.3. Disassembly of Top Cabinet 38 19.3. Tuner Extent, Panel & Volume Circuit 81 9.4. Disassembly of the DVD Lid (When taking out disc 19.4. Mic, USB Relay, USB, Tray Loading & Optical Pickup Unit 38 Circuit 82 9.5. Disassembly of Front Panel 39 20 Printed Circuit Board 85 9.6. Disassembly of Volume P.C.B. 39 20.1. DVD Module P.C.B. 85 9.7. Disassembly of Panel P.C.B. 40 20.2. Main P.C.B. 86 9.8. Disassembly of Mic P.C.B. 40 20.3. Panel, Volume & Tuner Extent P.C.B. 87 9.9. Disassembly of USB P.C.B. 40 20.4. Mic, USB, USB Relay & Tray Loading P.C.B. 88 manually) 9.10. Disassembly of Rear panel 41 9.11. Disassembly of DVD Mechanism Unit 41 9.12. Disassembly of DVD Module P.C.B. 41 9.13. Disassembly of USB Relay P.C.B. 42 9.14. Disassembly of Main P.C.B. & Tuner Extent P.C.B. 42 9.15. Replacement of Digital Amp IC (IC5100) 43 9.16. Replacement of Regulator IC (IC2903) 43 9.17. Disassembly of SMPS Module P.C.B. 44 10 Assembly and Disassembly of DVD Mechanism Unit 10.1. Disassembly Procedure 11 Service Position 21 Basic Troubleshooting Guide 89 21.1. Basic Troubleshooting Guide for Traverse Unit (DVD Module P.C.B) 21.2. Basic Troubleshooting Guide for SMPS/MAIN/PANEL 22 Overall Block Diagram for PT150 22.1. SC-PT150 Simplified Block 23 Terminal Function of ICs 23.1. IC2018 (C2CBYY000438): System Control IC 24 Exploded Views 45 89 90 91 91 92 92 93 45 24.1. Cabinet Parts Location 95 50 24.2. Packaging 97 11.1. Checking & Repairing Panel P.C.B. 50 11.2. Checking & Repairing Mic P.C.B. 50 25 Replacement Parts List 25.1. Component Parts List 4 98 99 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 1 Safety Precautions 1.1. GENERAL GUIDELINES 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed. 3. After servicing, carry out the following leakage current checks to prevent the customer from being exposed to shock hazards. 1.1.1. LEAKAGE CURRENT COLD CHECK 1. Unplug the AC cord and connect a jumper between the two prongs on the plug. 2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the chassis, the reading should be between 1MΩ and 5.2MΩ. When the exposed metal does not have a return path to the chassis, the reading must be 1.1.2. LEAKAGE CURRENT HOT CHECK 1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check. 2. Connect a 1.5kΩ, 10 watts resistor, in parallel with a 0.15µF capacitors, between each exposed metallic part on the set and a good earth ground such as a water pipe, as shown in Figure 1. 3. Use an AC voltmeter, with 1000 ohms/volt or more sensitivity, to measure the potential across the resistor. 4. Check each exposed metallic part, and measure the voltage at each point. 5. Reverse the AC plug in the AC outlet and repeat each of the above measurements. 6. The potential at any point should not exceed 0.75 volts RMS. A leakage current tester (Simpson Model 229 or equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 milliamp. In case a measurement is outside of the limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to the customer. Figure 1 1.2. Before Repair and Adjustment (Using SMPS Module P.C.B.) This unit uses Switching Mode Power Supply (SMPS) Module P.C.B. to provide the neccessary voltages for the unit. Caution: DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices. After repairs are completed, restore power gradually using a variac, to avoid overcurrent. Current consumption at AC 110-240 V, 50/60 Hz in NO SIGNAL mode volume minimal should be ~ 650 mA. Note: It is advisable to replace the SMPS Module P.C.B. as a unit. 1.3. Protection Circuitry The protection circuitry may have operated if either of the following conditions are noticed: · No sound is heard when the power is turned on. · Sound stops during a performance. 5 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are “shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used. If this occurs, follow the procedure outlines below: 1. Turn off the power. 2. Determine the cause of the problem and correct it. 3. Turn on the power once again after one minute. Note: When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again. 1.4. Safety Parts Information Safety Parts List: There are special components used in this equipment which are important for safety. These parts are marked by in the Schematic Diagrams & Replacement Parts List. It is essential that these critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire or other hazards. Do not modify the original design without permission of manufacturer. Reference No. 340 A2 A2 A2 Part No. RAE2023Z-S K2CQ2CA00002 K2CQ2CA00007 K2CT3CA00004 Table 1 Part Name & Description TRAVERSE UNIT AC CORD AC CORD AC CORD Remarks [M] [M] GCT [M] GC/GCP/GCS [M] GS · SMPS Module P.C.B.: Reference No. 40 F1 Table 2 Part No. N0AZ6GE00006 K5D502BNA005 6 Part Name & Description SMPS MODULE FUSE Remarks [M] (RTL) [M] SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 1.5. Caution for AC Cord (For Saudi Arabia and Kuwait) WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE LETTER E, BY THE EARTH SYMBOL OR COLOURED GREEN OR GREEN/YELLOW. ("GS" area code model only) For your safety, please read the following text carefully. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5-ampere fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5-ampere and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark A A or the BSI mark on the body of the fuse. THIS PLUG IS NOT WATERPROOF KEEP DRY. Before use Remove the connector cover. How to replace the fuse The location of the fuse differ according to the type of AC mains plug (figures A and B). Confirm the AC mains plug fitted and follow the instructions below. Illustrations may differ from actual AC mains plug. If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local dealer. 1. Open the fuse cover with a screwdriver. Figure A Figure B Fuse cover CAUTION! IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13-AMPERE SOCKET. 2. Replace the fuse and close or attach the fuse cover. Figure A Figure B Fuse (5 ampere) If a new plug is to be fitted please observe the wiring code as stated below. If in any doubt please consult a qualified electrician. IMPORTANT The wires in this mains lead are coloured in accordance with the following code: Blue: Neutral, Brown: Live. As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black or Blue. The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Brown or Red. 7 Fuse (5 ampere) SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 2 Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by electro static discharge (ESD). 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can generate electrical charge sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. Caution: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device). 8 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 3 Precaution of Laser Diode CAUTION : This product utilizes a laser diode with the unit turned on, invisible laser radiation is emitted from the pickup lens. Wavelength : 662nm/785nm Maximum output radiation power from pickup : 100µW/VDE Laser radiation from pickup unit is safety level, but be sure the followings: 1. Do not disassemble the pickup unit, since radiation from exposed laser diode is dangerous. 2. Do not adjust the variable resistor on the pickup unit. It was already adjusted. 3. Do not look at the focus lens using optical instruments. 4. Recommend not to look at pickup lens for a long time. 9 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 4 About Lead Free Solder (PbF) 4.1. Service caution based on legal restrictions 4.1.1. General description about Lead Free Solder (PbF) The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation. The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin (Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86°F) more than that of the normal solder. Definition of PCB Lead Free Solder being used The letter of “PbF” is printed either foil side or components side on the PCB using the lead free solder. (See right figure) Service caution for repair work using Lead Free Solder (PbF) · The lead free solder has to be used when repairing the equipment for which the lead free solder is used. (Definition: The letter of “PbF” is printed on the PCB using the lead free solder.) · To put lead free solder, it should be well molten and mixed with the original lead free solder. · Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC. · Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the lead free solder. · Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30 degrees C (662±86°F). Recommended Lead Free Solder (Service Parts Route.) · The following 3 types of lead free solder are available through the service parts route. RFKZ03D01K-----------(0.3mm 100g Reel) RFKZ06D01K-----------(0.6mm 100g Reel) RFKZ10D01K-----------(1.0mm 100g Reel) Note * Ingredient: tin (Sn), 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3% 10 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 5 Handling Precautions for Traverse Unit The laser diode in the optical pickup unit may break down due to static electricity of clothes or human body. Special care must be taken avoid caution to electrostatic breakdown when servicing and handling the laser diode. 5.1. Cautions to Be Taken in Handling the Optical Pickup Unit The laser diode in the optical pickup unit may be damaged due to electrostatic discharge generating from clothes or human body. Special care must be taken avoid caution to electrostatic discharge damage when servicing the laser diode. 1. Do not give a considerable shock to the optical pickup unit as it has an extremely high-precise structure. 2. To prevent the laser diode from the electrostatic discharge damage, the flexible cable of the optical pickup unit removed should be short-circuited with a short pin or a clip. 3. The flexible cable may be cut off if an excessive force is applied to it. Use caution when handling the flexible cable. 4. The antistatic FPC is connected to the new optical pickup unit. After replacing the optical pickup unit and connecting the flexible cable, cut off the antistatic FPC. 5.2. Grounding for electrostatic breakdown prevention Some devices such as the DVD player use the optical pickup (laser diode) and the optical pickup will be damaged by static electricity in the working environment. Proceed servicing works under the working environment where grounding works is completed. 5.2.1. Worktable grounding 1. Put a conductive material (sheet) or iron sheet on the area where the optical pickup is placed, and ground the sheet. 5.2.2. Human body grounding 1. Use the anti-static wrist strap to discharge the static electricity form your body. 11 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 12 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 6 Accessories Antenna wire Remote control Speaker label AC cord (For GC/GCP/GCS/GCT areas) Video cable AC cord (For GS area only) AC plug adaptor 13 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 7 Operation Procedures 7.1. Remote Control Key Buttons Operations Television operations Adjust the television volume Switch the main unit on or off Select the source DVD: DVD/CD FM EXT-IN: AUX, USB Change the television’s video input mode Show the current disc’s playback condition Select disc’s title numbers and etc., Enter numbers Adjust the volume of the main unit Select preset radio stations Basic operations for play Show a disc top menu or program list Show a disc menu or play list Select or confirm menu items on the television screen, Frame-by-frame Show on-screen menu Karaoke Return to previous screen, Show the Setup menu Show the display on the main unit Set the sleep timer This function enables you to turn off the unit automatically after the set time. SLEEP 30 SLEEP 60 OFF SLEEP 120 SLEEP 90 To mute the sound To cancel Press [MUTING] again or adjust the volume. Muting is cancelled when you switch the unit to standby. To cancel the timer Press and hold [ SLEEP] to select "OFF". To confirm the remaining time Press and hold [ SLEEP] again. 14 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 7.2. Main Unit Key Buttons Operations Standby/on switch [ /I] Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power. MIC jack / TUNING Connect a microphone MIC LEVEL Adjust the microphone volume Skipping or slow-search play, Select the radio stations OPEN/CLOSE Open or close the disc tray +, VOLUME Turn the volume up or down AC supply indicator [AC IN] This indicator lights when the unit is connected to the AC mains supply. Display SELECTOR DVD/CD USB FM AUX Returns to DVD/CD USB port Connect a USB device / TUNE MODE / FM MODE Stop playback, Select the tuning mode, Adjust the FM reception condition /MEMORY Disc playback, Memorize the receiving radio stations 15 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 7.3. About DivX VOD Content DivX Video-on-Demand (VOD) content is encrypted for copyright protection. In order to play DivX VOD content on this unit, you first n eed to register the unit. If you purchase DivX VOD content using a registration code different from this unit’s code, you will not be able to play this content. ("Authorization Error" is displayed.) Follow the online instructions for purchasing DivX VOD content to enter the unit’s registration code and register the unit. For more information about DivX VOD, visit www.divx.com/vod. Regarding DivX content that can only be played a set number of times Some DivX VOD content can only be played a set number of times. When you play this content, the remaining number of plays is displayed. You cannot play this content when the number of remaining plays is zero. ("RENTAL EXPIRED" is displayed.) When playing this content The number of remaining plays is reduced by one if you press [ ] or press and hold [ SETUP]. you press [ , STOP]. (Press [ , PAUSE] to pause play.) you press [ , ] (skip) or [ , ] (slow/search) etc. and arrive at another content or the start of the content being played. Resume (OI page 15, Stop) function does not work. Display the unit’ s registration code (OI page 23, "REGISTRATION (DIVX)" in "OTHERS" tab) We recommend that you make a note of this code for future reference. After playing DivX VOD content for the first time, another registration code is then displayed in "REGISTRATION (DIVX)". Do not use this registration code to purchase DivX VOD content. If you use this code to purchase DivX VOD content, and then play the content on this unit, you will no longer be able to play any content that you purchased using the previous code. 16 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 7.4. USB Connection and Operation Optional USB Optional USB connection connection and operation and operation 3 Adjust the volume of the main unit. The USB connectivity enables you to connect and play tracks or files f rom USB mass storage class devices. Typically, USB memory devices. (Bulk only transfer) Preparation Before connecting any USB mass storage device to the unit, ensure that the data stored therein has been backed up. It is not recommended to use a USB extension cable. The USB device is not recognised by this unit. 1 4 Connect the USB mass storage device (not included). USB enabled device (not included) It is not recommended to use a USB extension cable. The device connected via the cable will not be recognised by this unit. 2 Begin playback by selecting the track from the USB mass storage device. Example: OR OR To return to the previous screen Press [ RETURN]. To select "USB" as the source, press several times. For other operating functions, they are similar as those described on "DISC OPERATION". (OI page 14 to 25) USB AV AUX Compatible Devices D evices which are defined as USB mass storage class: USB devices that support bulk only transfer. USB devices that support USB 2.0 full speed. Select the desired item for playback. OR Example: Supported Formats File name File extension Still pictures JPG *1 Music MP3 WMA .mp3 .wma Video MPEG4 *2 .asf .jpg .jpeg * It may not be possible to play all the files due to the condition on how they were created. * 2 For Panasonic D-Snap/DIGA. 1 Note CBI (Control/Bulk/Interrupt) is not supported. Digital Cameras that use PTP protocol or which require additional program installation when connected to a PC are not supported. A device using NTFS file system is not supported. [Only FAT 16/32 (File Allocation Table 16/32) file system is supported]. Depending on the sector size, some files m ay not work. It will not operate with Janus enabled MTP (Media Transfer Protocol) devices. Maximum folder: 256 folders Maximum file:: 4000 files Maximum file name: 12 characters Maximum folder name: 12 characters Only one memory card will be selected when connecting a multiport USB card reader. Typically the first memory card inserted. 17 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 7.5. Audio and Video Connections 7.5.1. Television with Video In Terminal 7.5.2. Television with Component Video In Terminals 7.5.3. Audio Connection for Video Cassette Recorder or Television 18 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 7.5.4. Connection for Set Top Box 19 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 7.6. Disc Information 7.6.1. Disc Playability (Media) Discs that Discs that can can bebe played played Disc Logo Indicated in these instructions by Remarks DVD-Video High quality movie and music discs. Music discs with video. Video CD Including SVCD (Conforming to IEC62107). CD Music discs. Recorded discs ( Disc : Playable, : Not playable) Logo Recorded on a DVD video recorder, etc. 2 Recorded on a personal computer, etc. Finalizing 4 8 DVD-RAM Not necessary Necessary DVD-R/RW 3 DVD-R DL 6 9 Necessary +R/+RW ( ) 5 Necessary +R DL ( ) 5 Necessary CD-R/RW 1 Necessary 7 It may not be possible to play all the above-mentioned discs in some cases due to the type of disc, the condition of the recording, the recording method, or how the files were created [ Item 7.6.2 File Extension Type Support (WMA/MP3/JPEG/ MPEG4/DivX] 1 2 3 4 5 6 7 8 9 This unit can play CD-R/RW recorded with CD-DA or Video CD format. Discs recorded on DVD video recorders or DVD video cameras, etc. using Version 1.1 of the Video Recording Format (a unified video recording standard). Discs recorded on DVD video recorders or DVD video cameras using Version 1.2 o f the Video Recording Format (a unifi ed video recording standard). Discs recorded on DVD video recorders or DVD video cameras using DVD-Video Format. Recorded using a format different from DVD-Video Format, therefore, some functions cannot be used. A process that allows play on compatible equipment. To play a disc that is displa yed as "Necessary" on this unit, the disc must first be fi nalized on the device it was recorded on. Closing the session will also work. MPEG4 data recorded with the Panasonic SD multi cameras or DVD video recorders [conforming to SD VIDEO specifications (ASF standard)/MPEG4 (Simple Profile) video system/G.726 audio system]. Functions added with DivX ultra are not supported. Video systems Note about using a DualDisc This unit can play PAL and NTSC, but your television must match the system used on the disc. PAL discs cannot be correctly viewed on an NTSC television. This unit can convert NTSC signals to PAL 60 for viewing on a PAL television. (OI page 22, "NTSC DISC OUT" in "VIDEO" tab.) The digital audio content side of a DualDisc does not meet the technical specifi cations of the Compact Disc Digital Audio (CD-DA) format so playback may not be possible. Discs that cannot be played DVD-RW version 1.0, DVD-Audio, DVD-ROM, CD-ROM, CDV, CD-G, SACD, Photo CD, DVD-RAM that cannot be removed from their cartridge, 2.6-GB and 5.2-GB DVDRAM, and "Chaoji VCD" available on the market including CVD, DVCD and SVCD that do not conform to IEC62107. 20 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 7.6.2. File Extension Type Support (WMA/MP3/JPEG/MPEG4/DivX) Tips Tips for formaking making data data discs discs When there are more than eight groups, the eighth group onwards will be displayed on one vertical line in the menu screen. There may be differences in the display order on the menu screen and computer screen. This unit cannot play files recorded using packet write. DVD-RAM Discs must conform to UDF 2.0. DVD-R/RW Discs must conform to UDF bridge (UDF 1.02/ISO9660). This unit does not support multi-session. Only the default session is played. CD-R/RW Discs must conform to ISO9660 level 1 or 2 (except for extended formats). This unit supports multi-session but if there are many sessions it takes more time for play to start. Keep the number of sessions to a minimum to avoid this. Naming folders and files Files are treated as contents and folders are treated as groups on this unit. At the time of recording, prefix folder and file names. This should be with numbers that have an equal number of digits, and should be done in the order you want to play them (this may not work at times). Files must have the extension ( see below). (Extension: ".WMA" or ".wma") Compatible compression rate: between 48 kbps and 320 kbps. You cannot play WMA files that are copy-protected. This unit does not support Multiple Bit Rate (MBR). (Extension: ".MP3" or ".mp3") Compatible compression rate: between 32 kbps and 320 kbps. This unit does not support ID3 tags. Compatible sampling rates: DVD-RAM, DVD-R/RW: 11.02, 12, 22.05, 24, 44.1 and 48 kHz CD-R/RW: 8, 11.02, 12, 16, 22.05, 24, 32, 44.1 and 48 kHz (Extension: ".JPG", ".jpg", ".JPEG" or ".jpeg") JPEG files taken on a digital camera that conform to DCF Standard (Design rule for Camera F ile system) Version 1.0 are displayed. Files that have been altered, edited or saved with computer picture edi ting software may not be displayed. This unit cannot display moving pictures, MOTION JPEG and other such formats, and still pictures other than JPEG (Example: TIFF), or play pictures with attached audio. (Extension: ".ASF" or ".asf") You can play MPEG4 data [conforming to SD VIDEO specifications (ASF standard)/MPEG4 (Simple Profile) video system/G.726 audio system] recorded with Panasonic SD multi cameras or DVD video rec orders with this unit. The recording date may differ from that of the actual date. (Extension: ".DIVX", ".divx", ".AVI" or ".avi") You can play all versions of DivX video (including DivX 6) [DivX video system/MP3, Dolby Digital or MPEG audio system] with standard playback of DivX media files. Functions added with DivX Ultra are not supported. GMC (Global Motion Compensation) is not supported. DivX files greater than 2 GB or have no index may not be played properly on this unit. This unit supports all resolutions up to maximum of 720 x 480 (NTSC)/720 x 576 (PAL). You can select up to eight types of audio and subtitles on this unit. 21 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 8 Self-Diagnosis and Special Mode Setting 8.1. Service Mode Summary Table The service modes can be activated by pressing various button combination on the main unit and remote control unit. Below is the summary for the various modes for checking: Player buttons [STOP] Remote control unit buttons [0] [5] [PAUSE] [FUNCTIONS] [1] [3] [6] [7] [ ] [8] [EQ] [ENTER] [ [ [ [ ] ] ] ] Application Error code check. Jitter checking. Initial setting of laser drive current. DVD laser drive current check. ADSC internal RAM data check. CD laser drive current check. Region display and mode. Micro-processor firmware version check. Initialization of the player (factory setting is restored). Used after replacement of Micro-processor (DV5 LSI) IC, FLASH ROM IC (IC8651), EEPROM IC (IC8611) and DVD Module P.C.B. DVD Module P.C.B. firmware version check. CPPM/CRM keys check. DVD Module P.C.B. reset. Timer Timer Timer Timer 1 1 2 2 check. reset. check. reset. Note (Refer to the section “8.2.1. Service Mode Table 1” for more information.) (Refer to the section “8.2.2. Service Mode Table 2” for more information.) (Refer to the section “8.2.3. Service Mode Table 3“ for more information.) (Refer to the section “8.2.4. Service Mode Table 4“ for more information.) (Refer to the section “8.2.5. Service Mode Table 5“ for more information.) Note: An error code will be canceled if a power supply is turned OFF. *1: CPPM is the copy guard function beforehand written in the disk for protection of copyrights. *2: CEC is the consumer electronic control used for high-level user control of HDMI-connected devices. *3: HDCP is the specification developed to control digital audio & video contents transmission for DVI or HDMI connections. 8.2. Service Mode Table By pressing various button combinations on the main unit and remote control unit, you can activate the various service modes for checking. Special Note: · Due to the limitations of the no. characters that can be shown on the FL Display, the “FL Display” button on the remote control unit can be used to show the two display pages. (Display 1 / Display 2). · Refer to Section 7.1 for the section on “Remote Control Key Buttons Operations”. 22 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 8.2.1. Service Mode Table 1 Item Mode Name Jitter check Key Operation FL Display Description Jitter check. Jitter rate is measured and displayed. Measurement is repeatedly done in the cycle of one second. Read error counter starts from zero upon mode setting. When target block data failed to be read out, the counter advances by one increment. When the failure is caused by minor error, it may be corrected when retried to enable successful reading. In this case, the counter advances by one. When the error persists even after retry, the counter may jump by two or more. Front Key In STOP (no disc) mode, press [STOP] button on the main unit, and [5] button on the remote control unit. Press [POWER] button to exit. (Display 1) Jitter check Jitter rate mode Jitter rate is shown in decimal notation to one place of decimal. Focus drive value is shown in hexadecimal notation. (Display 2) Press [FL Display] on remote control unit for next page (FL Display). FL Display sequence: Display 1 2. Lead Error Counter Error code check Error code check The latest error code stored in the EEPROM IC is displayed. Note: Refer to "Section 8.3 DVD Self Diagnostic Function-Error Code" for more detailed information on the error codes. Initial setting of laser drive current Focus Drive Value Initial setting of laser drive current. Initial current value for the DVD laser and CD laser is separately saved in the EEPROM IC. FL Display sequence: Display 1 2. U/H/F Error code (play_err) is expressed in the following convention. Error code = 0 x DAXX is expressed: DVDnn U12 Error code = 0 x DBXX is expressed: DVDnn H12 Error code = 0 x DXXX is expressed: DVDnn F123 Error code = 0 x 0000 is expressed: DVDnn F--* "xx" denotes the error code (Display 1) Laser current measurement mode The value denotes the current in decimal notation. In STOP (no disc) mode, press [STOP] button on the main unit, and [0] button on the remote control unit. * With pointing of cursor up and down on display. Cancelled automatically 5 seconds later. To exit, press [POWER] button on main unit or remote control. In STOP (no disc) mode, press [STOP] button on the main unit, and [PAUSE] button on the remote control unit. Cancelled automatically 5 seconds later. (Display 2) Press [FL Display] on remote control unit for next page (FL Display) on values of laser drive current. CD Laser DVD Laser The above example shows the initial current is XXXmA and YYYmA for CD laser and DVD laser respectively when the laser is switched on. 23 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 8.2.2. Service Mode Table 2 Key Operation Item Mode Name DVD laser drive current measurement FL Display Description DVD laser drive current measurement. DVD laser drive current is measured and the result is displayed together with the initial value stored in the EEPROM IC. After the measurement, DVD laser emission is kept on. It is turned off when POWER key is switched off. FL Display sequence: Display 1 2. (Display 1) DVD laser current measurement mode The value denotes the current in decimal notation. (Display 2) Front Key In STOP (no disc) mode, press [STOP] button on the main unit, and [FUNCTIONS] button on the remote control unit. Cancelled automatically 5 seconds later. Press [FL Display] on remote control unit for next page (FL Display) on values of dvd drive current. DVD DVD Laser Laser Initial Value Value The above example shows the initial current is XXXmA and the measured value is YYYmA. ADSC internal RAM data check ADSC internal RAM data check. ADSC internal RAM data is read out and displayed. RAM data for specified address The value is shown in hexadecimal notation. The above example shows the data in ADSC address FBOh is XXXXh. Address CD laser drive current measurement CD laser drive current measurement. CD laser drive current is measured and the result is displayed together with the initial value stored in the EEPROM IC. After the measurement, CD laser emission is kept on. It is turned off when POWER key is switched off. FL Display sequence: Display 1 2. (Display 1) CD laser current measurement mode In STOP (no disc) mode, press [STOP] button on the main unit, and [1] button on the remote To exit, press [POWER] button. In STOP (no disc) mode, press [STOP] button on the main unit, and [3] button on the remote control unit. Cancelled automatically 5 seconds later. The value denotes the current in decimal notation. (Display 2) Press [FL Display] on remote control unit for next page. (FL Display) CD laser CD value laser initial value The above example shows the initial current is 0XXmA and the measured value is 0YYmA. 24 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 8.2.3. Service Mode Table 3 Item Mode Name Micro-processor firmware version display & EEPROM checksum display. Key Operation FL Display Description Front Key Micro-processor firmware version display & EEPROM checksum display. EEPROM checksum is only available due to existence of EEPROM IC. (Display 1) Note: Condition 1/2/3 shows the state of EEPROM IC. (Display 2) In STOP (no disc) mode, press [STOP] button on the main unit, and [7] button on the remote control unit. Cancelled automatically 5 seconds later. FL Display sequence: Display 1 2 3. Opecon Version (Condition1) EEPROM Checksum (If applicable, refer below.) If the version of the EEPROM does not match, [NG] is displayed. (Condition 2) (a) If there is NO EEPROM header string OR (b) If there is no EEPROM (no data is received by Micro-processor), [NO] is displayed. (Condition 3) If the EEPROM version matches, checksum [YYYY] is displayed. (Display 3) Press [FL Display] button on remote control unit for next page. (FL Display) Initialization Initialization. User settings are cancelled and player is initialized to factory setting. It is necessary when after replacement of Micro-processor (DV5 LSI) IC, FLASH ROM IC (IC8651), EEPROM IC (IC8611) & DVD Module P.C.B. In STOP (no disc) mode, press [STOP] button on the main unit, and [ 10] button on the remote control unit. Cancelled automatically 5 seconds later. Region display Region code display, TV broadcasting system & the model no. information. In STOP (no disc) mode, press [STOP] button on the main unit, and [6] button on the remote control unit. Cancelled automatically 5 seconds later. Model No. Information N: NTSC / 6: PAL60 N: no PAL / P: PAL Note: Refer to Figure 2 for "Video Design Information". Region No.: 0-8 25 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS Region TV Broadcasting Code System Model Series Country Region P, PC, PX USA, Canada, PX 1 NTSC NTSC (*A) (S) Japan 2 NTSC NTSC (*A) Signal System (Default) Product Region Display OSD Menu Language (Default) English, Spanish, Canadian 1PN French 2PN Japanese, English English, French, German, E Europe 2 PAL PAL (*C) 2P6 Spanish, Polish, Russian, Czech, Hungarian English, French, German, EB, EG 2 Europe PAL PAL (*C) 2P6 Italian, Spanish, Polish, Swedish, Dutch English, French, German, GC, GS Middle East GCS, GD, South East Asia, GT, GCT Korea, Taiwan 2 PAL PAL (*C) 2P6 Spanish, Polish, Russian, Czech, Hungarian GN PL, GCP, LB New Zealand, Australia 3 PAL NTSC NTSC (*B) 3PN PAL (*C) 4P6 English, Traditional Chinese English, French, German, 4 PAL Italian, Spanish, Polish, Swedish, Dutch Central/South/ Latin America 4 NTSC NTSC (*D) English, Spanish, French, 4PN Brazilian Portuguese English, French, German, EE CIS 5 SECAM PAL (*C) 5P6 Spanish, Polish, Russian, Czech, Hungarian GK China 6 PAL NTSC (*B) NTSC (*A) Source English, Simplified Chinese NTSC (*B) Output Source Screen Saver NTSC Screen Saver NTSC disc NTSC PAL disc 6PN NTSC disc PAL (DVD-V) Output NTSC NTSC (default) PAL60 NTSC (DVD-A/VCD) PAL disc PAL (*C) PAL60 NTSC (*D) Source Output Source Output Screen Saver PAL Screen Saver NTSC PAL60 (default) NTSC disc NTSC NTSC PAL disc NTSC NTSC disc PAL disc PAL Explanation of Display Individual Model Code N: If NTSC disc is played, NTSC output. 6: If NTSC disc is played, PAL60 output. can play PAL disc Region code Figure 2 26 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 8.2.4. Service Mode Table 4 Item Mode Name DVD Module P.C.B. firmware version display FL Display Description Front Key DVD Module P.C.B. firmware version is displayed on the FL Display. The firmware version can be updated using recovery disc. System controller version Destination System controller generation Region No.: 0-8 Note: It is necessary to check for firmware version before carrying out the version up using the disc. CPPM/CRM Keys Check CPPM/CRM refers to the Content Protection for Recordable Media and Pre-Recorded Media. It displays the existence of the keys as "1" or "0". OK: Existing of keys. NG: Non existing of keys. 0: NG 0: NG 1: OK 1: OK DVD Module P.C.B. Reset Key Operation In STOP (no disc) mode, press [STOP] button on the main unit, and [8] button on the remote control unit. Cancelled automatically 5 seconds later. In STOP (no disc) mode, press [STOP] button on the main unit, and [EQ] button on the remote control unit. Cancelled automatically 5 seconds later. While in initialization mode, press & hold [STOP] button on the main unit, follow by [ENTER] button on the remote control unit. Cancelled automatically 5 seconds later. To reset DVD Module P.C.B. This process is used when the DVD Module P.C.B. or FLASH ROM IC is replaced with a new one. 27 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 8.2.5. Service Mode Table 5 Item Mode Name Timer 1 check Key Operation FL Display Description Timer 1 check Laser operation timer is measured separately for DVD laser and CD laser. (Display 1) FL Display sequence: Display 1 2. DVD laser usage time Front Key In STOP (no disc) mode, press [STOP] button on the main unit, and [ ] button on the remote control unit. Cancelled automatically 5 seconds later. Shown to the above is DVD laser usage time, and to the below is CD laser usage time. Time is shown in 4 digits of decimal notation in a unit of 10 hours. "0000" will follow "9999". (DVD laser) (Display 2) Press [FL Display] button for next page of FL Display. CD laser usage time Time is shown in 4 digits of decimal notation in a unit of 10 hours. "0000" will follow "9999". (CD laser) Timer 1 reset Timer 2 check Timer 2 reset Timer 1 reset Laser operation timer of both DVD laser and CD laser is reset all at once. Time is shown in 4 digits of decimal notation in a unit of 10 hours. It will clear to "0000" upon reset. While displaying Timer 1 data, press [STOP] button on the main unit, and [ ] button on the remote control unit. Cancelled automatically 5 seconds later Time is shown in 5 digits of decimal notation in a unit of 1 hour. "00000" will follow "99999". In STOP (no disc) mode, press [STOP] button on the main unit, and [ ] button on the remote control unit. Cancelled automatically 5 seconds later. Timer 2 check Spindle motor operation timer Timer 2 reset Spindle motor operation timer Time is shown in 5 digits of decimal notation in a unit of 1 hour. It will be cleared to "00000" upon activating this. 28 While displaying Timer 2 data, press [STOP] button on the main unit, and [ ] button on the remote control unit. Cancelled automatically 5 seconds later. SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 8.2.6. Optical Pick-up Self-Diagnosis The optical pickup self-diagnosis function and tilt adjustment check function have been included in this unit. When repairing, use the following procedure for effective self-diagnosis and tilt adjustment. Be sure to use the self-diagnosis function before replacing the optical pickup when "NO DISC" is displayed. As a guideline, you should replace the optical pickup when the value of the laser drive current is more than 55. Note: Press the power button to turn on the power, and check the value within three minutes before the unit warms up. (Otherwise, the result will be incorrect.) Use the optical pickup self-diagnosis function. "NO DISC" is displayed, unit does not play smoothly, etc. Method: With no disc in the main unit: · Press the "FUNCTIONS" button on the remote control unit while pressing the "STOP" button on the main unit. (DVD) · Press the "3" button on the remote control unit while pressing the "STOP" button on the main unit. (CD) Check the laser drive current. Display content (display1/display2) LDD / (DVD) Factory setting Value is 23 (DVD), 34 (CD) or less. Value is more than 23 (DVD), 34 (CD). LDC / Factory setting Replace the optical pickup. (Refer to the section "OPTICAL PICKUP REPLACEMENT PROCEDURE" in this Guide.) Present value (CD) Present value Replace with a new optical pickup if the present value is more than 23 (DVD), 34 (CD). Cause: Damage due to static electricity during replacement. Check the laser drive current after replacement. Write the present value into the unit if it is 23 (DVD), 34 (CD) or less. Method: With no disc in the main unit: · Press the "FUNCTIONS" button on the remote control unit while pressing the "STOP" button on the main unit. (DVD) · Press the "3" button on the remote control unit while pressing the "STOP" button on the main unit. (CD) Do the optical pickup tilt adjustment. (Refer to the section "TILT ADJUSTMENT" in this Guide.) Use the tilt adjustment check function. Writing method: · Press the "PAUSE" button on the remote control unit while pressing the "STOP" button on the main unit. Note: Press "FL DISPLAY" button on remote control unit for next page display. Initialize the main unit. 29 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 8.3. 8.3.1. DVD Self Diagnostic Function-Error Code Mechanism Error Code Table Error Diagnosis Contents Description of error Code H01 Tray loading error The tray opening and closing is abnormal. CLOSE and OPEN of the tray cannot be carried out properly. Loading motor error, DV5 LSI IC (IC8001) error. H02 Spindle servo error The spindle servo/motor is abnormal. The FG pulse is abnormal. CLV servo error. Automatic FL Display Remarks Press [ STOP] on main unit for next error. (OPEN time: OPEN CLOSE OPEN H01 at CLOSE: CLOSE OPEN CLOSE H01) Press [ STOP] on main unit for next error. H03 Traverse servo error The traverse is abnormal. (Traverse servo, DV5 LSI IC (IC8001), TRV motor error.) Press [ STOP] on main unit for next error. H04 Tracking servo error Tracking coil NG (OPU unit abnormal), DV5 LSI IC (IC8001) error. H05 Seek time out error It is not possible to access the disc. TOC cannot read. Abnormal disc etc. Pickup abnormal or disk is dirty. (TRV motor error, DV5 LSI IC (IC8001) error.) H07 Driver IC thermal The spindle motor is abnormal. (short shut down between brushes) Press [ STOP] on main unit for next error. Press [ STOP] on main unit for next error. Press [ STOP] on main unit for next error. H15 Disc tray open detection switch failure The disc tray cannot be opened & it closes spontaneously. Press [ STOP] on main unit for next error. H16 Disc tray close detection switch failure The disc tray cannot be closed & it opens spontaneously. Press [ STOP] on main unit for next error. U11 Focus servo error Focus coil, FE signal error. Press [ STOP] on main unit for next error. (Unfinalized DVD-R is likely to beocme U11.) F500 DSC error DV5 LSI IC (IC8001) stops in the occurance of servo error (startup, focus error, etc) Press [ STOP] on main unit for next error. F506 Invalid media Disc is flipped over, TOC unreadable, incompatible disc. Press [ STOP] on main unit for next error. F620 OPU unit abnormality temperature Laser protection at high temperature. Press [ STOP] on main unit for next error. F621 OPU unit circuitry temperature Laser protection at circuit failure. Press [ STOP] on main unit for next error. U15 Unfinalized DVD-R 30 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 8.3.2. DVD Module Error Code Table Error Diagnosis Contents Description of error Code U702 DVD/DVI I2C The communication error of I2C communication error when connecting it with DVD/ DVI. For instance, when EDID information to which information on the TV set side has been described cannot be read, it is generated. Automatic FL Display Remarks Press [ STOP] on main unit for next error. U703 DVD/DVI attestation error When attestation (HDCP) with the TV side fails when connecting it with DVD/DVI, it is generated. Press [ STOP] on main unit for next error. U704 DVD/DVI SRM Riborcerar It is generated at the equipment to which the TV set is Riborced when connecting it with DVD/DVI. Press [ STOP] on main unit for next error. U705 DVD/DVI SRM disk falsification check error It is generated at the time of it is time when illegal the SRM data of the reproducing disk (verify error), when connecting it with DVD/DVI. Press [ STOP] on main unit for next error. F740 DVD device key I2C error when writing DVD Key device into transmitter. Press [ STOP] on main unit for next error. F893 FLASH ROM IC data Firmware error, DV5.0 LSI IC (IC8651) falsification error error. Press [ STOP] on main unit for next error. F894 EEPROM IC abnormality error When failing in the access to EEPROM IC located in the DVD Module P.C.B. (IC8611) Press [ STOP] on main unit for next error. F895 Language area abnormal Firmware version agreement check for factory preset setting failure prevention. Press [ STOP] on main unit for next error. F896 No existence model Firmware version agreement check for factory preset setting failure prevention. Press [ STOP] on main unit for next error. F897 Initialization error Incomplete initialization after writing of new firmware (Factory preset setting failure prevention) Press [ STOP] on main unit for next error. F898 Disagreement of hardware and software Unsuitable combination of AV Decoder, SDRAM & FLASH ROM IC (firmware). Press [ STOP] on main unit for next error. F899 The communication specification disagreement between micro-processor Unsuitable combination of number of system com and panel com used. (Frimware) Press [ STOP] on main unit for next error. 31 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 8.3.3. Power Supply Error Code Table Error Diagnosis Contents Code F61 The abnormalities in an output or power supply circuit of POWER AMP F76 Abnormality in the output voltage of stabilized power supply 8.3.4. Description of error Automatic FL Display Remarks In normal operation, when DCDET2 goes to "L" (Low) (Not during POWER OFF condition), F61 appears on FL Display and PCONT goes to "L" (Low). This is due to speaker output has DC voltage or fan is not working. Press [ STOP] on main unit for next error. In normal operation when DCDET1 is detected "L" (Low) for two consecutive times, F76 is displayed on FL for 2 seconds and after that PCONT will be turned to "L" (Low). This is due to any of the DC voltages (+9V, +7V, -7V, +5V, +5.3V etc.) not available. Press [ STOP] on main unit for next error. ECC Error Code Table Error Diagnosis Contents Code F600 Administrative information cannot be acquired by the recovery error. F601 Irregular sector ID was demanded. Description of error Automatic FL Display Remarks It becomes impossible NaviPack etc. were done, and not to be able to acquire necessary information in the navigation’s changing due to wound etc. of DISC, and to have done the reproduction transition. Press [ STOP] on main unit for next error. It tried to access the position that did not exist on DISC by the recording error etc. of authoring. Press [ STOP] on main unit for next error. F603 KEYDET cannot be The data for decoding copyright acquired by the protection (CSS) cannot be acquired recovery error. due to wound etc. of DISC, and it is not possible to reproduce. 32 Press [ STOP] on main unit for next error. SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 8.3.5. USB Error Code Table Error Diagnosis Contents Description of error Code F650 USB device: Devices Devices other than the mass storage other than mass class are connected. storage Automatic FL Display Remarks Press [ STOP] on main unit for next error. F651 USB device: NonFull Speed Device The device that the transfer rate did not correspond to Full Speed was connected. Press [ STOP] on main unit for next error. F652 USB device: Interface NG The device in the interface (subclass) outside correspondence was connected. (correspondence interface) 001b: Reduced Block Commands (RBC) 010b: SFF-8020i. MMC-2 (ATAPI) 110b: SCSI transparent command set. Press [ STOP] on main unit for next error. F655 USB device: Overcurrent detection The overcurrent of 500mA or more was detected in VDD USB, and the USB device driver function was intercepted. (To intercept the current.) Press [ STOP] on main unit for next error. 8.4. Sales Demonstration Lock Function This function prevents discs from being lost when the unit is used for sales demonstrations by disabling the disc eject function. "LOCKED" is displayed on the unit, and ordinary operation is disabled. 8.4.1. Setting · Prohibiting removal of disc 1. Select the DVD/CD function. 2. At POWER ON condition, press and hold down the button and the power button on the player for at least three seconds. (The message, “___LOCKED_” appears when the function is activated.) Note: OPEN/CLOSE is invalid and the player displays “___LOCKED_” while the lock function mode is entered. · Prohibiting operation of selector and disc 1. Select the DVD/CD function. 2. At POWER ON condition, press and hold down the button and the power button on the player for at least three seconds. (The message, “___LOCKED_” appears when the function is activated.) Note: The following buttons are invalid and the player displays “___LOCKED_” while the lock function mode is entered. Player , , SELECTOR, /, , / Remote NUMERIC KEYS 0~9, , , , , , , , FUNCTIONS/KARAOKE, TOP controller unit MENU/DIRECT NAVIGATOR, RETURN/SETUP, FL DISPLAY/SLEEP, MUTING, MENU/PLAY LIST, TEST, EXT-IN, FM, UP, DOWN, LEFT & RIGHT 8.4.2. Cancellation The lock can be cancelled by the same procedure as used in setting. ("UNLOCKED" is displayed on cancellation. Disconnecting the power cable from power outlet does not cancel the lock.) 33 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 8.5. Service Precautions 8.5.1. Recovery after the DVD player is repaired · When the FLASH ROM IC or DVD Module P.C.B. is replaced, carry out the recovery processing to optimize the drive. Playback the recovery disk to process the recovery automatically. · Recovery disc (Product number: RFKZD03R005) [SPG] · Performing recovery process 1. Load the recovery disc RFKZD03R005 on to the player and run it. 2. Recovery is performed automatically. When it is finished, a message appears on the screen. 3. Remove the recovery disc. 4. Turn off the power. 5. Initialize the player. 8.5.2. Firmware version-up of the DVD player · The firmware of the DVD player may be renewed to improve the quality including operability and playability to the substandard discs.processing to optimize the drive. The recovery disc has also firmware version-up. · After version-up, recovery processing is executed automatically. · Part number of the recovery disc for version-up will be noticed when it is supplied. · Updating firmware 1. Load the recovery disc on to the player and run it. 2. Firmware version of the player is automatically checked. Appropriate message appears whenever necessary. 3. Using remote controller´s cursor key, select whether version updating is to be done or not. (Selection of Yes/No) 4. a. If Yes is selected, version updating is performed. b. If No is selected, only recovery is performed. 5. a. When updating is finished, remove the disc according to the message appearing on the screen. b. Remove the disc according to the message appearing on the screen. 6. Turn off the power. Note: If the AC power supply is shut out during version-up due to a power failure, the version-up is improperly carried out. In such a case, replace the FLASH ROM IC and carry out the version-up again. 8.5.3. DVD Module P.C.B. Reset · When after replacing FLASH ROM IC or DVD Module P.C.B., FL displays error code “ DVD F897”. This means the unit is not initialized properly and the following process needs to be carry out. · Procedures: 1. Press on remote control while pressing “STOP” button on main unit. (To enter into initialization) 2. FL display show “INIT” 3. While still pressing “STOP” button on main unit, press “ENTER” on remote control. (To reset the unit) 4. FL will display “RESET” before FL display will change to TOC reading again. 5. Power off unit. Unplug the AC cord. 6. Power on the unit. It should be no problem. If problem persist check on the DVD Module P.C.B. or FLASH ROM IC. 34 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 9 Assembling and Disassembling “ATTENTION SERVICER” Be careful when disassembling and servicing. Some chassis components may have sharp edges. Special Note: 1. This section describes the disassembly procedures for all the major printed circuit boards and main components. 2. Before the disassembly process was carried out, do take special note that all safety precautions are to be carried out. (Ensure that no AC power supply is connected during disassembling.) 3. For assembly after operation checks or replacement, reverse the respective procedures. Special reassembly procedures are described only when required. 4. The Digital Amp IC may have high temperature after prolonged use. 5. Use caution when removing the top cabinet and avoid touching heat sinks located in the unit 6. This unit uses Switching Mode Power Supply (SMPS) Module P.C.B. for providing the voltage supply. It is advisable to replace as a unit. Do not attempt to replace any individual components on board. 7. Select items from the following index when checks or replacement are required. · Disassembly of Top Cabinet · Disassembly of DVD Lid (When taking out disc manually) · Disassembly of Front Panel · Disassembly of Volume P.C.B. · Disassembly of Panel P.C.B. · Disassembly of Mic P.C.B. · Disassembly of USB P.C.B. · Disassembly of Rear Panel · Disassembly of DVD Mechanism Unit · Disassembly of DVD Module P.C.B. · Disassembly of USB Relay P.C.B. · Disassembly of Main P.C.B. & Tuner Extent P.C.B. · Replacement of Digital Amp IC (IC5100) · Replacement of Regulator IC (IC2903) · Disassembly of SMPS Module P.C.B. 35 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS · SMPS Module P.C.B. Replacement: 1. This model uses SMPS Module P.C.B. to provide the necessary supply voltages for the unit. 2. It is advisable to replace the SMPS Module P.C.B. once upon detecting of non-working conditions. Do not attempt to repair or replace it by components. 3. Non-working conditions include: lWith AC supply but no supply voltages after checking at CN2 and/or CN3 respectively. lBroken fuse. (Substitute compatible part for fuse: K5D502BNA005) lWire connection problem. lNon-working parts in SMPS Module P.C.B. (Check components) 9.1. Disassembly Flow Chart 9.3. Top Cabinet 9.4. DVD Lid 9.9. Rear Panel 9.5. Front Panel 9.14. Main P.C.B. & Tuner Extent P.C.B. 9.6. Volume P.C.B. 9.15. Digital Amp IC (IC5100) 9.7. Panel P.C.B. 9.16. Regulator IC (IC2903) 9.9. USB P.C.B. 9.8. Mic P.C.B. 9.11. DVD Mechanism Unit 9.12. DVD Module P.C.B. 9.13. USB Relay P.C.B. 36 9.17. SMPS Module P.C.B. SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 9.2. Main Components and P.C.B. Locations 37 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 9.3. Disassembly of Top Cabinet Step 1 Remove 4 screws. Step 2 Remove 3 screws at the rear panel Step 3 Lift up and remove the top cabinet. Step 2 Insert the gear jig into the tray open/ close hole. Step 3 Turn the gear jig counterclockwise to open the tray. Note : Do not use force to push the tray backwards as it can damage the mechanism unit. 9.4. Disassembly of the DVD Lid (When taking out disc manually) · Follow (Step 1) to (Step 3) of Item 9.3. Step 1 Detach the gear (For drawing out tray) from the mechanism unit. It inserts a screw driver in the gear. (The gear jig) Step 4 Release the tabs and remove the DVD lid. 38 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS Note: You can return the tray by turning the gear jig clockwise. 9.5. Step 6 Detach USB shield wire from the connector (CN8000) on USB P.C.B. Disassembly of Front Panel Step 7 Remove the front panel. · Follow (Step 1) to (Step 3) of Item 9.3. · Follow (Step 1) to (Step 4) of Item 9.4. Step 1 Remove 1 screw from the panel angle. Step 2 Detach FFC cables from the connectors (CN2005, CN2006 & CN2007) on Main P.C.B. Step 3 Release the tab on each side of the front panel. Special Note : Avoid placing the set in a position that might cause damage to the jacks when removing the front panel. 9.6. Disassembly of Volume P.C.B. · Follow (Step 1) to (Step 3) of Item 9.3. · Follow (Step 1) to (Step 4) of Item 9.4. · Follow (Step 1) to (Step 7) of Item 9.5. Step 4 Upset the unit and release 3 hooks at the bottom chassis. Step 1 Remove the volume knob. Step 5 Detach the front panel slightly forward in the direction of arrow. Caution: Do not attempt to exert strong force when detaching the front panel. 39 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 9.8. Disassembly of Mic P.C.B. Step 2 Remove 4 screws from Volume P.C.B.. · Follow (Step 1) to (Step 3) of Item 9.3. Step 3 Remove Volume P.C.B. · Follow (Step 1) to (Step 4) of Item 9.4. · Follow (Step 1) to (Step 7) of Item 9.5. · Follow (Step 1) to (Step 3) of Item 9.6. · Follow (Step 1) to (Step 4) of Item 9.7. Step 1 Remove the mic knob. 9.7. Disassembly of Panel P.C.B. · Follow (Step 1) to (Step 3) of Item 9.3. · Follow (Step 1) to (Step 4) of Item 9.4. Step 2 Remove Mic P.C.B. · Follow (Step 1) to (Step 7) of Item 9.5. · Disassembly of Mecha Holder. Step 1 Remove 2 screws. Step 2 Remove the mecha holder. 9.9. Disassembly of USB P.C.B. · Follow (Step 1) to (Step 3) of Item 9.3. · Follow (Step 1) to (Step 4) of Item 9.4. · Follow (Step 1) to (Step 7) of Item 9.5. · Follow (Step 1) to (Step 4) of Item 9.7. Step 1 Remove USB P.C.B. · Disassembly of Panel P.C.B. Step 3 Release 2 hooks. Step 4 Remove Panel P.C.B. 40 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS Step 1 Remove 2 screws from the DVD mechanism unit. Step 2 Detach FFC cable from the connectors (CN2001) on Main P.C.B. and (CS901) on Tray Loading P.C.B. 9.10. Disassembly of Rear panel · Follow (Step 1) to (Step 3) of Item 9.3. Step 1 Remove 7 screws from the rear panel. Step 3 Lift up the DVD mechanism unit and detach FFC cable from the connector (CN8003) on USB Relay P.C.B.. Step 4 Remove DVD mechanism unit. Step 2 Remove the fan wire clamper to detach the fan unit connector (CN5704) on Main P.C.B. Step 3 Release the tab on each side of the rear panel in the direction of arrows. Step 4 Remove the rear panel. 9.12. Disassembly of DVD Module P.C.B. · Follow (Step 1) to (Step 3) of Item 9.3. · Follow (Step 1) to (Step 4) of Item 9.4. · Follow (Step 1) to (Step 4) of Item 9.11. Step 1 Remove 4 screws from DVD Module P.C.B. 9.11. Disassembly of DVD Mechanism Unit · Follow (Step 1) to (Step 3) of Item 9.3. · Follow (Step 1) to (Step 4) of Item 9.4. 41 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 9.13. Disassembly of USB Relay P.C.B. · Follow (Step 1) to (Step 3) of Item 9.3. · Follow (Step 1) to (Step 4) of Item 9.4. · Follow (Step 1) to (Step 4) of Item 9.11. Step 1 Remove 1 screw. Step 2 Detach FFC cable from the connector (CN8002). Step 3 Lift up and remove USB Relay P.C.B. Step 2 Lift up DVD Module P.C.B. and detach FFC cable from the connector (FP8251). 9.14. Disassembly of Main P.C.B. & Tuner Extent P.C.B. · Follow (Step 1) to (Step 3) of Item 9.3. · Follow (Step 1) to (Step 4) of Item 9.10. Step 3 Turn over DVD Module P.C.B. and detach FFC cable from the connector (FP8531). Step 1 Remove 1 screw from the bracket. Step 4 Remove DVD Module P.C.B. Step 2 Remove the bracket. · Disassembly of Bracket. · Disassembly of Main P.C.B. & Tuner Extent P.C.B. Caution : Do not use strong or excessive force to avoid damage to FFC cables. Step 3 Remove 4 screws on Main P.C.B. 42 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS Step 4 Detach FFC cable from the connectors (CN2 & CN3) on SMPS Module P.C.B., (CN2001,CN2005, CN2006 & CN2007) on Main P.C.B. and (CS901) on Tray Loading P.C.B. Step 2 Remove 2 screws from the digital amp IC (IC5100). Step 3 Remove the digital amp IC (IC5100) from the heatsink unit. Step 5 Remove Main P.C.B. & Tuner Extent P.C.B. Caution : Handle the heatsink unit with caution due to its high temperature after prolonged use. Touching it may lead to injuries. 9.15. Replacement of Digital Amp IC (IC5100) · Follow (Step 1) to (Step 3) of Item 9.3. Note : For replacement of IC5200 & IC5300, repeat the (Step 1) to (Step 3). Refer to the diagrams of Main P.C.B. (Item 9.14) for the location of the parts. · Follow (Step 1) to (Step 4) of Item 9.9. · Follow (Step 1) to (Step 5) of Item 9.14. 9.16. Replacement of Regulator IC (IC2903) Step 1 Desolder pins of the digital amp IC (IC5100) on the back side of Main P.C.B. · Follow (Step 1) to (Step 3) of Item 9.3. · Follow (Step 1) to (Step 4) of Item 9.9. · Follow (Step 1) to (Step 5) of Item 9.14. Step 1 Desolder pins of the regulator IC (IC2903) on the back side of Main P.C.B. 43 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS Step 2 Remove 1 screw from the regulator IC (IC2903). Step 2 Detach FFC cable from the connectors (CN2 & CN3) on SMPS Module P.C.B. Step 3 Remove the regulator IC (IC2903) from the heatsink extrusion. Step 3 Remove 1 screw from the rear panel. Caution : Handle the heatsink extrusion with caution due to its high prolonged use. Touching it may lead to injuries. Step 4 Release tab of the rear panel in the direction of arrow. Step 5 Remove SMPS Module P.C.B. Note : Refer to the diagrams of Main P.C.B. (Item 9.14.) for the location of the part. 9.17. Disassembly of SMPS Module P.C.B. · Follow (Step 1) to (Step 3) of Item 9.3. Caution Note: The SMPS Module P.C.B. is advisable to be replaced as a unit. Do not attempt to replace any individual components on board. Step 1 Remove 4 screws from SMPS Module P.C.B. 44 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 10 Assembly and Disassembly of DVD Mechanism Unit 10.1. Disassembly Procedure Step 4 Remove the traverse unit. 10.1.1. Disassembly of Traverse Unit (with Middle Chassis) Step 1 Slide the lever (A) in the arrow direction (to the opposite side) till it stops. Step 2 Slide the lever (A) further by bending the tab at the right side of the lever A in the right direction. (The right groove opens and the boss becomes seen.) Step 3 Open the lever (B) to left. (The 2 grooves at the left side open.). 10.1.2. Disassembly of Tray Step 1 Slide the clamp plate while pressing the stopper in the arrow direction, and remove the clamp plate. 45 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS l(Assembly of the tray unit) Step 2 Raise the mecha chassis vertically. Step 1 Insert a part of the tray into the unit sliding over the groove on the mecha chassis. Step 3 Slide the lever in the arrow direction till it stops and pull the tray out. Step 2 Insert the tray to the point before the tab of the mecha chassis. Step 4 Spread the tabs at the both sides and pull the tray out. (The tray slides a little forword and stops.). Step 3 Hook the drive arm concave phase over the tray and the tray slider. Step 4 Press in the tray. Step 5 Make sure that the tray and the drive arm move smoothly. Step 5 Remove the drive arm concave phase from the tray slider and tray. 46 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS Step 4 Remove the belt. Step 5 Unlock the tab and remove the pulley gear. 10.1.3. Disassembly of Loading Section Step 6 Remove the relay gear. Step 1 Spread the tabs at the both sides and push out the drive arm. Step 7 Turn the change lever in the arrow direction till it stops. Step 8 Hook the change lever spring on the change lever project part temporarily. Step 2 Hook the lock lever spring on the lock lever projection part temporarly. Step 3 Unlock the tab and remove the lock lever. 47 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS Step 9 Pull the lever (B) at the bottom side in the direction of arrow and remove the change lever. 10.1.5. Disassembly of Traverse Unit Step 1 Spread the tabs to push in the pin in the direction of arrows. Step 10 Remove the drive rack, the sub rack and the drive gear in the direction of arrow. Step 2 Remove 4 fixed pins. 10.1.4. Disassembly of Tray Loading P.C.B. Step 1 Remove 3 screws Step 2 Remove Tray Loading P.C.B. 48 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS Step 3 Remove the middle chassis. Step 4 Remove the traverse unit. 49 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 11 Service Position 11.3. Checking & Repairing Main P.C.B. 11.1. Checking & Repairing Panel P.C.B. Step 1 Remove the top cabinet. Step 2 Remove the DVD lid. Step 1 Remove the top cabinet. Step 3 Disassemble the front panel. Step 2 Remove the DVD lid. Step 4 Disassemble Panel P.C.B. Step 3 Disassemble the front panel. Step 5 Disassemble Volume P.C.B. Step 4 Disassemble Panel P.C.B. Step 6 Disassemble Mic P.C.B. Step 5 Disassemble Volume P.C.B. Step 7 Disassemble USB P.C.B. Step 6 Disassemble Mic P.C.B. Step 8 Disassemble the DVD mechanism unit. Step 7 Disassemble USB P.C.B. Step 9 Disassemble USB Relay P.C.B. Step 10 Disassemble the rear panel. Step 8 Connect FFC cable at the connectors (CN2005, CN2006 & CN2007) on Main P.C.B. and (CN8000) on USB P.C.B. Step 11 Disassemble Main P.C.B. & Tuner Extent P.C.B. Step 12 Disassemble SMPS Module P.C.B. Step 9 Turn over Panel P.C.B. horizontally and place it according to the diagram shown below. Step 13 Position Panel P.C.B., Volume P.C.B., Mic P.C.B., USB P.C.B., DVD mechanism unit, USB Relay P.C.B., SMPS Module P.C.B., Main P.C.B. & Tuner Extent P.C.B. according to diagram shown below. 11.2. Checking & Repairing Mic P.C.B. · Follow (Step 1) to (Step 8) of Item 11.1. Step 14 Connect FFC cable at the connectors (CN2001, CN2005, CN2006, CN2007 & CN5704) on Main P.C.B., (CS901) on Tray Loading P.C.B., (CN2 & CN3) on SMPS Module P.C.B., (CN8000) on USB P.C.B. and (CN8003) on USB Relay P.C.B. Step 1 Turn over Mic P.C.B. horizontally and place it according to the diagram shown below. 50 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 11.5. Checking & Repairing DVD Module P.C.B. · Follow (Step 1) to (Step 14) of Item 11.3. Step 1 Turn over the DVD mechanism unit according to the diagram shown below. Step 15 Turn over the Main P.C.B. vertically and place it according to the diagram. 11.4. Checking & Repairing SMPS Module P.C.B. · Follow (Step 1) to (Step 14) of Item 11.3. Step 1 Turn over the SMPS Module P.C.B. according to the diagram shown below. 51 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 12 Measurements and Adjustments 12.1. Service Tools and Equipment Application Tilt adjustment Name Number DVDT-S20 [SPG] DVD test disc TORX screw driver (T6) Others Confirmation Available on sales route. (T6) or RFKZ0185 [SPG] RFKXPG641 [SPG] PVCD-K06 or any other commercially available disc PVCD-K06 or any other commercially available disc RFKZD03R005 [SPG] Grease CD test disc VCD test disc Recovery disc 12.2. Important points in adjustment 12.2.1. Important points in optical adjustment · Before starting optical adjustment, be sure to take anti-static measures. · Optical pickup tilt adjustment is needed after replacement of the following components. 1. Optical pickup unit 2. Spindle motor unit 3. Optical pickup peripheral parts Notes Adjustment is generally unnecessary after replacing other parts of the traverse unit. However, make adjustment if there is a noticeable degradation in picture quality. Optical adjustments cannot be made inside the optical pickup. Adjustment is generally unnecessary after replacing the traverse unit. 12.2.2. Important points in electrical adjustment · Follow the adjustment procedures described in this manual. 12.3. Storing and handling of test discs · Surface precision is vital for DVD test discs. Be sure to store and handle them carefully. 1. Do not place discs directly onto the workbench, etc., after use. 2. Handle discs carefully in order to maintain their flatness. Place them into their case after use and store them vertically. Store discs in a cool place where they are not exposed to direct sunlight or air from air conditioners. 3. Accurate adjustment will not be possible if the disc is warped when placed on a surface made of glass, etc. If this happens, use a new test disc to make optical adjustments. 4. If adjustment is done using a warped disc, the adjustment will be incorrect and some discs will not be playable. 52 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 12.4. Optical adjustment 12.4.1. Optical pickup tilt adjustment Measurement point Adjustment point Tangential adjustment screw Tilt adjustment screw Measuring equipment None (Main unit display for servicing is used.) Mode Disc T01 (inner periphery) play DVDT-S20 [SPG] T30 (center periphery) T43 (outer periphery) play Adjustment value Adjust to the minimum jitter value. 12.4.1.1. Adjustment procedure 1. While pressing STOP button on the main unit, press "5" on the remote control unit. 2. Confirm that "J_xxx/yyy_zz" (display1/display2) is shown on the front display. For your information: "yyy" and "zz" shown to the right have nothing to do with the jitter value. "yyy" is the error counter, while "zz" is the focus drive value. Note: Jitter value appears on the front display. 3. Play test disc T30 (center periphery). 4. Adjust tangential adjustment screw so that the jitter value is minimized. 5. Play test disc T30 (center periphery). 6. Adjust tilt adjustment screw 1 so that the jitter value is minimized. 7. Play test disc T30 (center periphery). 12.4.1.3. Check after adjustment 8. Adjust tilt adjustment screw 2 so that the jitter value is minimized. Play test disc or any other disc to make sure there is no picture degradation in the inner, middle and outer peripheries, and no audio skipping. After adjustment is finished, lock each adjustment screw in position using screw lock. 9. Repeat adjusting tilt adjustment screws 1 and 2 alternately until the jitter value is minimized. 12.4.1.2. Important points 12.4.1.4. Procedure for screw lock 1. Make tangential adjustment first, and then make tilt adjustment. 1. After adjustment, remove top cover, tray, clamper base and traverse unit in this sequence. 2. Repeat adjusting two or three times to find the optimum point. 2. Lay the traverse unit upside down, and fix adjustment screw with screw lock. 3. Finish the procedure with tilt adjustment. 3. After fixing, reassemble traverse unit, clamper base, tray and top cover. Jitter value depends on the model: 1. If the jitter value changes like B, the optimum point is easy to find. 2. If the jitter value changes like A, set the optimum point near the middle. 53 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 13 Abbreviations INITIAL/LOGO A A0~UP ACLK AD0~UP ADATA ALE AMUTE AREQ ARF ASI ASO ASYNC B BCK BCKIN BDO BLKCK BOTTOM BYP BYTCK C CAV CBDO CD CDSCK CDSRDATA CDRF CDV CHNDATA CKSL CLV COFTR CPA CPCS CPDT CPUADR CPUADT CPUIRQ CPRD CPWR CS CSYNCIN CSYNCOUT D DACCK DEEMP DEMPH DIG0~UP DIN DMSRCK DMUTE DO DOUT0~UP DRF DRPOUT DREQ DRESP DSC DSLF DVD INITIAL/LOGO E EC ECR ABBREVIATIONS ADDRESS AUDIO CLOCK ADDRESS BUS AUDIO PES PACKET DATA ADDRESS LATCH ENABLE AUDIO MUTE AUDIO PES PACKET REQUEST AUDIO RF SERVO AMP INVERTED INPUT SERVO AMP OUTPUT AUDIO WORD DISTINCTION SYNC BIT CLOCK (PCM) BIT CLOCK INPUT BLACK DROP OUT SUB CODE BLOCK CLOCK CAP. FOR BOTTOM HOLD BYPATH BYTE CLOCK CONSTANT ANGULAR VELOCITY CAP. BLACK DROP OUT COMPACT DISC CD SERIAL DATA CLOCK CD SERIAL DATA CD RF (EFM) SIGNAL COMPACT DISC-VIDEO CHANNEL DATA SYSTEM CLOCK SELECT CONSTANT LINEAR VELOCITY CAP. OFF TRACK CPU ADDRESS CPU CHIP SELECT CPU DATA CPU ADDRESS LATCH CPU ADDRESS DATA BUS CPU INTERRUPT REQUEST CPU READ ENABLE CPU WRITE ENABLE CHIP SELECT COMPOSITE SYNC IN COMPOSITE SYNC OUT D/A CONVERTER CLOCK DEEMPHASIS BIT ON/OFF DEEMPHASIS SWITCHING FL DIGIT OUTPUT DATA INPUT DM SERIAL DATA READ CLOCK DIGITAL MUTE CONTROL DROP OUT DATA OUTPUT DATA SLICE RF (BIAS) DROP OUT SIGNAL DATA REQUEST DATA RESPONSE DIGITAL SERVO CONTROLLER DATA SLICE LOOP FILTER DIGITAL VIDEO DISC F G H I L M O P 54 ENCSEL ETMCLK ETSCLK FBAL FCLK FE FFI FEO FG FSC FSCK GND HA0~UP HD0~UP HINT HRXW IECOUT IPFRAG IREF ISEL LDON LPC LRCK MA0~UP MCK MCKI MCLK MDATA MDQ0~UP MDQM MLD MPEG ODC OFTR OSCI OSCO OSD P1~UP PCD PCK PDVD PEAK PLLCLK PLLOK PWMCTL PWMDA PWMOA, B ABBREVIATIONS ERROR TORQUE CONTROL ERROR TORQUE CONTROL REFERENCE ENCODER SELECT EXTERNAL M CLOCK (81MHz/40.5MHz) EXTERNAL S CLOCK (54MHz) FOCUS BALANCE FRAME CLOCK FOCUS ERROR FOCUS ERROR AMP INVERTED INPUT FOCUS ERROR AMP OUTPUT FREQUENCY GENERATOR FREQUENCY SUB CARRIER FS (384 OVER SAMPLING) CLOCK COMMON GROUNDING (EARTH) HOST ADDRESS HOST DATA HOST INTERRUPT HOST READ/WRITE IEC958 FORMAT DATA OUTPUT INTERPOLATION FLAG I (CURRENT) REFERENCE INTERFACE MODE SELECT LASER DIODE CONTROL LASER POWER CONTROL L CH/R CH DISTINCTION CLOCK MEMORY ADDRESS MEMORY CLOCK MEMORY CLOCK INPUT MEMORY SERIAL COMMAND CLOCK MEMORY SERIAL COMMAND DATA MEMORY DATA INPUT/OUTPUT MEMORY DATA I/O MASK MEMORY SERIAL COMMAND LOAD MOVING PICTURE EXPERTS GROUP OPTICAL DISC CONTROLLER OFF TRACKING OSCILLATOR INPUT OSCILLATOR OUTPUT ON SCREEN DISPLAY PORT CD TRACKING PHASE DIFFERENCE PLL CLOCK DVD TRACKING PHASE DIFFERENCE CAP. FOR PEAK HOLD CHANNEL PLL CLOCK PLL LOCK PWM OUTPUT CONTROL PULSE WAVE MOTOR DRIVE A PULSE WAVE MOTOR OUT A, B SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS INITIAL/LOGO R RE RFENV RFO RS RSEL RST RSV S SBI0, 1 SBO0 SBT0, 1 SCK SCKR SCL SCLK SDA SEG0~UP SELCLK SEN SIN1, 2 SOUT1, 2 SPDI SPDO SPEN SPRCLK SPWCLK SQCK SQCX SRDATA SRMADR SRMDT0~7 SS STAT STCLK STD0~UP STENABLE STSEL STVALID SUBC SBCK SUBQ SYSCLK T TE TIBAL TID TIN TIP TIS TPSN TPSO TPSP TRCRS TRON TRSON ABBREVIATIONS READ ENABLE RF ENVELOPE RF PHASE DIFFERENCE OUTPUT (CD-ROM) REGISTER SELECT RF POLARITY SELECT RESET RESERVE SERIAL DATA INPUT SERIAL DATA OUTPUT SERIAL CLOCK SERIAL DATA CLOCK AUDIO SERIAL CLOCK RECEIVER SERIAL CLOCK SERIAL CLOCK SERIAL DATA FL SEGMENT OUTPUT SELECT CLOCK SERIAL PORT ENABLE SERIAL DATA IN SERIAL DATA OUT SERIAL PORT DATA INPUT SERIAL PORT DATA OUTPUT SERIAL PORT R/W ENABLE SERIAL PORT READ CLOCK SERIAL PORT WRITE CLOCK SUB CODE Q CLOCK SUB CODE Q DATA READ CLOCK SERIAL DATA SRAM ADDRESS BUS SRAM DATA BUS 0~7 START/STOP STATUS STREAM DATA CLOCK STREAM DATA STREAM DATA INPUT ENABLE STREAM DATA POLARITY SELECT STREAM DATA VALIDITY SUB CODE SERIAL SUB CODE CLOCK SUB CODE Q DATA SYSTEM CLOCK TRACKING ERROR BALANCE CONTROL BALANCE OUTPUT 1 BALANCE INPUT BALANCE INPUT BALANCE OUTPUT 2 OP AMP INPUT OP AMP OUTPUT OP AMP INVERTED INPUT TRACK CROSS SIGNAL TRACKING ON TRAVERSE SERVO ON INITIAL/LOGO V VBLANK VCC VCDCONT W X 55 VDD VFB VREF VSS WAIT WDCK WEH WSR X XALE XAREQ XCDROM XCS XCSYNC XDS XHSYNCO XHINT XI XINT XMW XO XRE XSRMCE XSRMOE XSRMWE XVCS XVDS XVSYNCO ABBREVIATIONS V BLANKING COLLECTOR POWER SUPPLY VOLTAGE VIDEO CD CONTROL (TRACKING BALANCE) DRAIN POWER SUPPLY VOLTAGE VIDEO FEED BACK VOLTAGE REFERENCE SOURCE POWER SUPPLY VOLTAGE BUS CYCLE WAIT WORD CLOCK WRITE ENABLE HIGH WORD SELECT RECEIVER X´ TAL X ADDRESS LATCH ENABLE X AUDIO DATA REQUEST X CD ROM CHIP SELECT X CHIP SELECT X COMPOSITE SYNC X DATA STROBE X HORIZONTAL SYNC OUTPUT XH INTERRUPT REQUEST X´ TAL OSCILLATOR INPUT X INTERRUPT X MEMORY WRITE ENABLE X´ TAL OSCILLATOR OUTPUT X READ ENABLE X SRAM CHIP ENABLE X SRAM OUTPUT ENABLE X SRAM WRITE ENABLE X V-DEC CHIP SELECT X V-DEC CONTROL BUS STROBE X VERTICAL SYNC OUTPUT SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 14 Voltage and Waveform Chart 14.1. DVD Module P.C.B. Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY 1 1.2 2 1.4 3 1.5 4 0 5 0 6 3.4 7 1.8 8 1.3 9 1.4 21 0.6 22 0.4 23 2.3 24 0.5 25 1.4 26 2.6 27 2 28 0.8 29 1.8 41 1.8 42 0 43 0 44 1.3 45 0 46 3.4 47 3.4 48 3.4 49 3.4 61 0.1 62 0 63 0 64 0.8 65 0.1 66 1.9 67 1.6 68 0 69 3.2 81 0 82 0 83 1.2 84 3.2 85 0.8 86 2.3 87 0 88 1.8 89 0 101 0 102 0 103 0.4 104 0.1 105 0.2 106 1.9 107 3.3 108 0 109 2.2 121 1.8 122 2.0 123 2 124 1.7 125 0 126 1.7 127 1.7 128 3.4 129 0.9 141 3.4 142 3.4 143 0 144 0 145 0 146 0 147 3.4 148 1.5 149 1.7 161 2.9 162 3.2 163 2.9 164 3.1 165 0 166 3.4 167 3.2 168 3.1 169 3 181 3.3 182 0 183 1.6 184 3.4 185 1.6 186 0 187 1.3 188 3.3 189 3.3 201 3.4 202 0.1 203 2.2 204 0.1 205 0 206 3.4 207 0.3 208 1.6 209 1.6 1 3.3 2 3.1 3 3.4 4 3.2 5 3.1 6 0 7 3.1 8 3.3 9 3.4 21 1.6 22 0 23 0.1 24 0.4 25 0.4 26 1.6 27 3.4 28 0 29 1.6 41 0 42 3.1 43 3.4 44 3.2 45 3.1 46 0 47 3 48 3.2 49 3.4 1 3.4 2 - 3 0.1 4 - 5 4.4 6 - 7 - 8 4.7 1 2.5 2 2.5 3 0 4 1.3 5 0.8 1 1.7 2 1.7 3 1.7 4 2.2 5 2.2 6 1.8 7 0 8 5.1 9 3.3 21 8.9 22 8.8 23 1.7 24 1.7 25 1.7 26 1.7 27 3.3 28 5.1 29 0 1 0 2 3.3 3 2.9 4 3.3 5 1.6 6 0.9 7 1.7 8 1.7 9 5.2 22 23 2.5 5.2 IC8601 2 3 3.3 0 24 0 25 2.6 26 2.5 27 2.6 1 3.3 2 3.3 28 5.1 IC8606 3 0 4 0 IC8001 10 11 1.2 1.3 IC8001 30 31 0.7 3.4 IC8001 50 51 1.7 0 IC8001 70 71 3.2 0 IC8001 90 91 0.5 1.8 IC8001 110 111 1.7 2.6 IC8001 130 131 0.9 0.4 IC8001 150 151 1.7 0.9 IC8001 170 171 3 3.1 IC8001 190 191 3.2 3.1 IC8001 210 211 0 1.2 IC8051 10 11 3 3 IC8051 30 31 1.8 1.7 IC8051 50 51 2.9 2.9 IC8111 12 0 13 1.1 14 1 15 0 16 3.4 17 1.3 18 1.1 19 1.9 20 0.7 32 0 33 3.4 34 0.7 35 1.1 36 1.5 37 1.6 38 1.8 39 1.4 40 2 52 3.4 53 2.8 54 2.8 55 3 56 3.4 57 3.2 58 3.2 59 0 60 3.2 72 3.2 73 3.2 74 0 75 0.1 76 0 77 0 78 0 79 0 80 0 92 3.3 93 2.2 94 2.2 95 1.8 96 1.8 97 1.7 98 1.7 99 1.7 100 1.7 112 2.6 113 2.6 114 2.6 115 2.7 116 2.7 117 2.4 118 2.5 119 2.5 120 2.5 132 3.3 133 2.4 134 1 135 1 136 2.4 137 0 138 0.4 139 0.9 140 0 152 1.7 153 0 154 3.4 155 1.5 156 1.6 157 0 158 1.3 159 3 160 3.1 172 3 173 0 174 3.4 175 3.2 176 3 177 3.1 178 2.9 179 2.9 180 2.9 192 0.1 193 2.1 194 0 195 0 196 3 197 1.5 198 0 199 0 200 1.6 212 1.8 213 2.7 214 2.5 215 1.4 216 1 12 0 13 2.9 14 3.4 15 2.9 16 3.3 17 3.3 18 3.3 19 3.2 20 2.2 32 1.7 33 0.1 34 0.1 35 0.1 36 0 37 3.4 38 1.5 39 2.9 40 0 52 0 53 3 54 0 12 2.8 13 2.6 14 2.6 15 4.1 16 4.3 17 4.8 18 3.7 19 0 20 3.3 12 0.1 13 0.1 14 0 15 2.5 16 2.5 17 5.2 18 0 19 2.5 20 2.5 1 0 2 0 3 0 4 0 5 3.2 6 3.3 7 0 8 3.3 12 3.3 13 3.3 14 3.3 15 1.6 16 1.6 17 0.6 18 1.2 19 1.5 20 1.7 32 1.6 33 1.0 34 1.6 35 2.3 36 1.4 37 3.3 38 1.7 39 1.1 40 1.4 IC8151 21 2.5 1 1.2 4 0 IC8251 10 11 0 2.4 IC8251 30 0 IC8421 10 11 0 0.9 IC8421 IC8611 1 1.1 2 1.0 3 1.8 4 1.0 5 1.7 6 2.3 7 1.3 8 1.8 9 1.2 21 1.8 22 1.8 23 2 24 1.9 25 0 26 2 27 0 28 2.5 29 1.7 41 1.6 42 1.7 43 1.7 44 2 45 1.9 46 0 47 3.3 48 0.8 5 IC8651 10 11 0.1 3.3 IC8651 30 31 1.1 0.8 IC8651 56 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY Ref No. MODE CD PLAY IC8691 3 0 1 3 2 3 1 0.1 3 5.1 B 0.4 E 1.5 E 0.1 2 5.1 Q8321 C 0 Q8551 C 4.6 4 5 4.6 5.1 IC9005 4 5 3.3 2.2 B 0.1 E 0.1 1 0.1 2 0.1 3 1.4 QR8111 4 5 0.1 0.1 E 1.1 6 3.3 Q8325 C 0 Q8552 C 4.6 6 4.4 1 2.7 2 2.7 7 0.1 8 3.4 IC8695 3 0 B 0.9 E 1.1 B 4.6 E 1.9 QR8420 C 0.1 E 0 4 4.2 Q8331 C 0 Q8561 C 3.5 B 4.0 5 5.1 1 1.6 B 0.4 E 1.6 B 1.3 E 3.5 QR8571 C 3.3 E 3.4 2 0.1 Q8335 C 0 Q8562 C 4.1 IC9003 3 4 1.6 1.7 5 3.3 6 1.6 B 0.9 E 1.5 Q8341 C 0 B 0.9 B 4.1 B 0.1 SA-PT150GC/GS/GCS/GCT/GCP DVD MODULE P.C.B. 57 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 14.2. Main P.C.B. Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY IC2004 1 - 2 5.2 5.2 3 0 0 4 0 0 5 0 0 6 0 0 7 0 0 8 - 1 0 0 2 2.2 5 3 4 5.1 4 3.6 5.2 5 0 0 6 2.8 5 7 0 0 8 0 0 9 0 0 21 5.2 5.2 22 0 0 23 0 0 24 0 0 25 0 0 26 0 0 27 0 0 28 4.4 4.5 29 4.1 4.1 41 0 0 42 0 0 43 0 0 44 0 0 45 0 0 46 0 0 47 0 0 48 0 0 49 0 0 61 0 0 62 5.1 5.1 63 0 0 64 0 0 65 5.1 5.1 66 0 0 67 5.1 5.1 68 5.1 5 69 0 5 81 0 0 82 0 0 83 5.1 5.1 84 0 0 85 4.1 0 86 2.5 2.3 87 1.9 2 88 5.2 5.2 89 2.6 2.6 1 0 0 2 0 0 3 0 0 4 0 0 5 0 0 6 0 0 7 0 0 8 0 0 9 0 0 21 0 0 22 0 0 23 0 0 24 0 0 25 0 0 26 0 0 27 0 0 28 0 0 29 0 0 41 0 42 0 0 43 0 0 44 0 0 45 0 0 46 0 0 47 0 0 48 0 0 49 0 0 61 0 0 62 -0.1 -0.1 63 0 0 64 0 0 65 4.8 4.8 66 0 0 67 5.6 5.6 68 0 0.1 69 0 0 81 0 0 82 0 0 83 0 0 84 0 0 85 -6.2 -6.4 86 6.3 6.5 87 0 0 88 0 0 89 0 0 1 4.9 4.9 2 0 0 3 2.1 2.1 4 4.8 4.8 5 1.6 1.5 7 1.6 1.5 8 2.1 2.1 9 0 0 21 0 0 22 1.3 1.3 25 1.3 1.3 27 0 0 28 1.4 1.4 29 1.6 1.6 1 1.6 1.6 2 0 0 23 24 1.3 0 1.3 0 IC2903 3 4 1.7 1.7 1.7 1.7 6 0 0 IC2801 26 1.3 1.3 5 3.4 3.4 6 1.7 1.7 1 25.9 26.0 2 12.7 12.8 3 0 0 4 12.6 12.7 5 4.7 4.7 6 0 0 7 0 0 8 0 0 9 0 3.0 1 25.9 26.0 2 12.7 12.7 3 0 0 4 12.7 12.7 5 4.7 4.7 6 0 0 7 0 0 8 0 0 9 3.0 3.0 1 25.9 25.6 2 12.7 12.7 3 0 0 4 13.0 12.7 5 4.7 4.6 6 0 0 7 0 0 8 0 0 9 0 3.0 1 - 2 2.6 2.6 3 2.6 2.6 6 0.6 0.6 7 0.6 0.6 8 0 0 9 2.6 2.6 1 0 0 2 0 0 Q2003 C 2.2 0.1 Q2905 C 5.2 5.2 Q2974 C -25.4 -25.3 Q5741 C 4.9 4.9 Q7100 C 0 0 3 0 0 6 0 0 Q2004 C 0 0 Q2906 C -23.3 -23.3 Q3003 C 1.6 1.6 Q5742 C 0.1 0.1 Q7101 C 0 0 7 6.7 6.7 8 7 7 E 0 0 E 0 0 E -21.8 -21.7 E 0 0 E 0 0 4 5 2.6 2.6 2.6 2.6 IC7101 4 5 -7 0 -7 0 B 0 0 E 0 0 B 0 0 E -7.5 -7.5 B -22.4 -22.3 E 1.6 1.6 B 0 0 E 0 0 B 0 0 E 0 0 B 4.5 0 E 1.1 0 B -7.0 -7.0 E -6.3 -6.9 B 0 0 E 0 0 B 0.7 0.7 1 0 0 B 5 5 E 0 0 IC2018 10 11 0 0 0 0 IC2018 30 31 2.7 0 2.8 0 IC2018 50 51 0 0 0 0 IC2018 70 71 5.2 5.1 5.2 5.1 IC2018 90 91 0.4 5.2 0.4 5.2 IC2102 10 11 0 0 0 0 IC2102 30 31 0 0 0 0 IC2102 50 51 1.3 0 1.4 0 IC2102 70 71 0 0 0 0 IC2102 90 91 0 0 0 0 IC2801 10 11 0 0 1.5 0 30 0 0 13 2.4 2.5 14 0 0 15 2.5 2.5 16 5.1 5.1 17 5.1 5.1 18 5.1 5.1 19 3.2 3.2 20 0 0 32 0 0 33 0 0 34 0 0 35 5.2 5.2 36 5.2 5.2 37 5.1 5.1 38 5.2 5.2 39 0 0 40 5.1 5 52 0 0 53 0 0 54 0 0 55 0 0 56 0 0 57 0 0 58 0 0 59 0 0 60 0 0 72 0 0 73 0 0 74 0 0 75 0 0 76 0 0 77 0 0 78 0 0 79 0 4.6 80 5.1 5 92 1.7 1.7 93 3.1 3.1 94 4.8 4.8 95 2.1 2.1 96 0 0 97 5.2 5.2 98 5.2 5.2 99 5.1 5.1 100 5.1 5.1 12 0 0 13 0 0 14 0 0 15 0 0 16 0 0 17 0 0 18 0 0 19 0 0 20 0 0 32 0.1 0.1 33 0 0 34 0 0 35 0 0 36 0 0 37 0 0 38 0 0 39 0 0 40 0.1 0.1 52 0 0 53 0 0 54 0.1 0.1 55 0 0 56 0 0 57 0 0 58 0 0 59 0 0 60 0 0 72 0 0 73 0 0 74 0 0 75 0 0 76 0 0 77 0 0 78 0 0 79 0 0 80 0 0 92 0 0 93 0 0 94 0 0 95 0 0 96 0 0 97 0 0 98 0 0 99 0 0 100 0 0 12 2.1 2.1 13 4.8 4.8 14 2.1 2.1 17 2.2 2.2 18 0 0 19 2.2 2.2 20 2.2 2.2 1 0 0 2 2.5 2.5 15 16 4.9 2.2 4.9 2.2 IC2802 3 4 4.9 2.5 4.9 2.5 5 0 0 6 2.5 2.5 13 2.6 2.6 14 0.9 0.9 15 5.2 5.2 31 2.2 2.2 IC5100 10 11 12.7 0 12.8 0 IC5200 10 11 12.7 0 12.8 0 IC5300 10 11 12.7 0 12.7 0 IC7100 10 11 2.6 2.6 2.6 2.6 Q2006 C 0 0 Q2907 C -21.0 -21.0 Q3008 C 0 0 Q5744 2 4.6 4.6 Q7102 C 0 0 12 4.2 5.1 12 12.7 12.8 12 12.7 12.7 12 12.8 12.8 12 2.6 2.6 B 0.5 0 E 0 0 B -6.8 -6.4 E 12.9 12.9 B 0.6 0.6 E 0 0 3 0.1 0.1 1 5.6 5.6 Q2030 C B 0 4.7 0 4.6 Q2910 C B 21.2 13.5 21.2 13.5 Q3009 C B 0.2 0.2 0.1 0 Q5745 2 3 4.4 0 4.4 0 16 - E 0 0 E 3.2 3.2 E 8.9 8.9 4 0.4 0.4 Q2801 C 4.8 4.6 Q2914 C 3.5 3.2 Q5740 C 17.1 17.1 E 0 0 B 0 2 B 3.7 3.8 B 9.5 9.5 Q5746 C 0.1 0.1 B 4.8 4.8 B 0 0 SA-PT150GC/GS/GCS/GCT/GCP MAIN P.C.B. 58 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 14.3. Panel P.C.B. Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY Ref No. MODE CD PLAY STANDBY 1 0 0 2 0 0 3 0 0 4 0 0 5 2.9 2.9 6 2.2 2.1 7 1.8 1.9 8 4 4 9 2.3 2.2 21 -24.4 -24.3 22 -24.4 -24.3 23 -24.3 -24.3 24 -17.2 -17.2 25 -14.8 -14.9 26 -24.4 -24.3 27 -24.4 -24.3 28 -24.4 -24.3 29 14.8 -17.2 41 -22.2 -22.2 42 -22.2 -22.2 43 5 5 44 0 0 IC6901 10 11 2.2 2.2 2.2 2.2 IC6901 30 31 -24.8 -15 -24.8 -15 IC6901 12 0 0 13 5 5 14 -24.4 -24.4 15 -22 -24.4 16 -24.4 -22 17 -24.4 -24.4 18 -19.6 -14.9 19 -19.8 -19.6 20 -15 -12.5 32 -22 -15 33 -22.3 -22.2 34 -22.2 -22.2 35 -22.2 -22.2 36 -22.2 -22.2 37 -22.2 -22.2 38 -22.2 -22.2 39 -22.2 -22.2 40 -22.2 -22.2 SA-PT150GC/GS/GCS/GCT/GCP PANEL P.C.B. 14.4. Tray Loading & SMPS Module P.C.B. Ref No. MODE CD PLAY STANDBY 1 5.1 5.1 2 7.5 7.6 3 0.6 0.6 4 7.5 7.6 IC904 5 0 0 6 7.5 7.6 7 0.6 0.6 8 2.8 2.8 9 5.1 5.1 SA-PT150GC/GS/GCS/GCT/GCP TRAY LOADING P.C.B. Ref No. MODE CD PLAY STANDBY 1 18.5 18.5 CN2 2 3 18.5 0 18.5 0 4 0 0 1 6 6 2 3.5 3.5 3 0 0 4 10.5 10.5 5 0 0 CN3 6 0 0 7 5 5 8 -12.3 -12.2 9 -16.1 -16.0 10 5.2 5.2 11 24.7 -24.7 SA-PT150GC/GS/GCS/GCT/GCP SMPS MODULE P.C.B. Ref No. MODE CD PLAY STANDBY 1 0 0 2 0 0 3 0 0 IC2204 4 5 -7 0 -7 0 6 0 0 7 6.7 6.7 8 7 7 SA-PT150GC/GS/GCS/GCT/GCP MIC P.C.B. 59 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 14.5. Waveform Chart 14.5.1. Waveform 1 WF No. IC2018-13 (PLAY) WF No. IC2018-15 (PLAY) WF No. IC2102-79,80,81,82 83,84 (PLAY) WF No. IC2102-95,99 (PLAY) 200Vp-p(5msec/div) 3.4Vp-p(50nsec/div) 1.4Vp-p(200usec/div) 2Vp-p(200usec/div) WF No. IC2102-96 (PLAY) WF No. IC2102-100 (PLAY) WF No. IC2801-4 (PLAY) WF No. IC2801-6 (PLAY) 0.3Vp-p(200sec/div) 0.7Vp-p(200usec/div) 0.7Vp-p(20usec/div) 1.2Vp-p(20usec/div) WF No. IC2801-8,11 (PLAY) WF No. IC2801-13,15 (PLAY) WF No. IC2801-18,21 (PLAY) WF No. IC2801-24 (PLAY) 1.3Vp-p(100nsec/div) 3.4Vp-p(2usec/div) 0.25Vp-p(20usec/div) 3.4Vp-p(20usec/div) WF No. IC2801-30 (PLAY) WF No. IC5100- 2,12(PLAY) WF No. IC5100-6,8 (PLAY) WF No. IC5200- 2,12(PLAY) 3.4Vp-p(20usec/div) 0.6Vp-p(200usec/div) 2.1Vp-p(200usec/div) 0.6Vp-p(200usec/div) WF No. IC5200-6,8 (PLAY) WF No. IC5300- 2,12(PLAY) WF No. IC5300-6,8 (PLAY) WF No. IC6901-5 (PLAY) 2.1Vp-p(200usec/div) 0.6Vp-p(200usec/div) 2.1Vp-p(200usec/div) 2.1Vp-p(5usec/div) WF No. IC8001-64,67 (PLAY) WF No. IC8001-95,96 (PLAY) WF No. IC8001-122,126 (PLAY) WF No. IC8001-146 (PLAY) 0.4Vp-p(200usec/div) 3.4Vp-p(200usec/div) 4Vp-p(200usec/div) 6.4Vp-p(2usec/div) 60 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 14.5.2. Waveform 2 WF No. IC8251-12,15,17 (PLAY) WF No. IC8251-14 (PLAY) WF No. IC8421-16,19,20,21 22,26,27 (PLAY) WF No. IC8421-15 (PLAY) 3.4Vp-p(200usec/div) 0.1Vp-p(200usec/div) 3.4Vp-p(200usec/div) 2Vp-p(200usec/div) 61 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 15 Illustration of IC's, Transistors and Diodes C0ABBB000230 (8p) C0CBCBD00018 (8p) C0DBZYE00002 (8p) C0EBA0000029 (4p) C0FBBK000050 (28p) C0JBAB000908 (6p) No.1 C1AB00001731 (6p) C1BB00001061 (16p) C3ABPG000145 (54p) C9ZB00000461 (32p) C0HBB0000057 (44p) C1AB00002463 (100p) C2CBYY000438 (100p) MN2DS0018MP (216p) No.1 RFKWMHC0B320 (GC/GCP/GS) RFKWMHC0D320 (GCS/GCT) 48 25 1 24 C0GBG0000048 C0GAY0000013 AN17831A C0DBEHG00006 28 22 30 3 21 1 4 12 29 8 B1ACKD000005 B 35 72 E 46 C B0EAKM000117 E B1ABCF000176 B1ABGC000005 B1ADCE000012 B1ADCF000001 B1ADGB000008 B1GBCFJJ0051 B1GDCFJJ0047 UNR511V00L UNR521100L 2SD1819A0L 2SB1218ARL B3AAA0000803 MA2J11100L MAZ82200ML Ca Cathode A A Anode Cathode Anode Anode Cathode Ca A E 3 C B XP0621400L 4 3 2 B MA2J72800L Ca Cathode Anode 2 12 C 1 1 45 9 14 AN30071A-NM B1BACG000023 B1BCCG000002 5 1 1 15 7 C0EBE0000456 C0JBAA000502 B0ACCK000005 B0BC3R400001 B0BC7R500001 B0JCAE000001 B0JCPD000025 Ca A B0ADCJ000020 Anode Cathode 62 Cathode Ca Ca Anode A A 6 1 B0BC5R000009 B0BC013A0007 Cathode Anode 5 Cathode Ca Anode A SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 16 Wiring Connection Diagram PbF 10 10 JK2002 1 VIDEO OUT D 1 CN2002 3 Z6900 1 CP2010 1 2 3 B PANEL P.C.B. (SOLDER SIDE) TUNER EXTENT P.C.B. (SOLDER SIDE) CN2010 2 10 4 COMPONENT VIDEO OUT 6 PbF 2 1 5 7 AUX 1 CN6001 12 13 SENSOR TO TUNER PACK UNIT 9 8 1 4 H6004 VR6800 E MIC VOLUME VOLUME P.C.B. (SOLDER SIDE) JK6802 VR6081 PbF 1 7 H2004 1 2 3 VOLUME 4 48 50 47 49 1 8 2 3 1 F CN2001 7 4 5 MIC MIC P.C.B. 3 2 (SOLDER SIDE) JK5000 CN2007 1 H6903 1 2 12 SURROUND SPEAKER L CN8002 5 CN8000 7 PbF 5 1 PbF 6 11 SURROUND SPEAKER R 13 12 CN8001 5 C 10 FRONT SPEAKER L 4 1 4 3 2 1 CN8003 H MAIN P.C.B. (SOLDER SIDE) 4 2 5 3 1 USB P.C.B. (SOLDER SIDE) PbF 9 FRONT SPEAKER R TO USB G USB RELAY P.C.B. (SOLDER SIDE) 3 8 CENTER SPEAKER 2 CN5704 1 CN2006 7 SUBWOOFER 1 7 3 TO OPTICAL PICKUP 1 TO SPINDLE MOTOR ASS’Y H2002 1 11 1 5 10 15 20 26 CN2005 4 H2001 1 1 1 4 FP8531 6 FP8251 5 1 FP9001 PbF FP8101 1 TO FAN UNIT A A DVD MODULE P.C.B. (SIDEA) DVD MODULE P.C.B. (SIDE:B) CN2 50 1 REF NO 316 4 + CN3 SMPS MODULE P.C.B. AC - CS901 7 1 CN1 M I PbF TRAY LOADING P.C.B. (SOLDER SIDE) 1 11 110V-240V 50/60HZ PbF PbF PbF SA-PT150GC/GS/GCS/GCT/GCP WIRING CONNECTION 63 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 64 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 17 Block Diagram 17.1. System Control FL6901 IC2018 C2CBYY000438 M+9V 2 G1 P1 P17 P1 P17 1 TRAY CLOSE H2004 4 TRAY OPEN 1 MIC EN FLD OUT H2004 CS901 9 3 CONTROL H2004 CS901 1 7 H2004 CS901 VREF 8 VCC CN6001 CN2007 8 FROM AMP & POWER 6 21 -VP 30 CS901 TRAY LOADING MOTOR DRIVE DRIVE G1 H2004 2 7 G10 CS901 S902 OPEN 3 CN6001 CN2007 FL2 DISPLAY DRIVER S901 PLAY TRAY LOADING MOTOR FL1 IC6901 C0HBB0000057 VREF IC904 C0GAY0000013 G10 FL DISPLAY SYSTEM CONTROL Q2030 4 VREF CONTROL 2 TRY CCW 3 TRY CW CN2007 CN6001 87 FLD CLK 85 FLD STB 86 7 D IN 11 CN2007 CN6001 8 CLK 10 CN2007 CN6001 9 STB 12 OSC 100 BRAKE H 5 VREF 98 RMT 18 VREF Z6900 (REMOTE SENSOR) VREF CN2007 CN6001 VREF 4 STANDBY LED D6900 Q2004 15 X IN 13 X OUT 30 DVD CMD 28 DVD CLK 29 DVD STAT 42 DVD MUTE 36 TUN CLK -VP LED DRIVE STBLED CN2007 CN6001 2 X2001 10MHz FP8101 CN2001 DVD CMD 2 TO/FROM DVD (VIDEO/ AUDIO) FP8101 CN2001 DVD CLK 3 FP8101 CN2001 MUTE F SW 68 DVD STAT 1 FP8101 CN2001 TUNER PACK Q2006 ZFLAG 23 MUTE FRONT MUTE F SW MUTE FRONT 69 STYB STYB 71 CN2002 TUN CLK 2 CN2002 TUN DI 3 CN2002 TUN SD 4 CN2002 TUN ST 6 38 TUN DI 35 TUN SD 37 TUN DO RESET 12 PCONT PCONT 40 DC DET2 88 DC DET2 DC DET1 70 DC DET1 ASP CLK 83 ASP CLK ASP DAT 84 ASP DAT TO/FROM AUDIO RESET SYS6V TO/FROM AMP & POWER SYNC SYNC 19 Q2003 VREF VCC CTRL VCC CTRL 65 SCART MUTE SCART MUTE 79 VR6800 (VOLUME) JOG A (VOL UP) RGB TO DVD VIDEO 81 RGB YC H CN2005 76 H6004 1 CN2005 JOG B 77 (VOL DOWN) H6004 2 82 YC H MUTE C S 67 WIDE 1 80 WIDE 1 VIDEO MUTE 46 VMUTE MUTE C TO AUDIO POWER S6800 VREF IC2004 EEPROM (Not Supplied) KEY1 DI 5 CN2007 CN6001 97 5 23 EDA DO 6 SK 4 24 ECK CS 3 25 ECS VREF KEY2 91 CN2005 OPEN/CLOSE FORWARD REVERSE STOP PLAY SELECTOR S6801 S6802 S6803 S6804 S6805 S6806 H6004 3 SA-PT150GC/GCP/GCS/GCT/GS SYSTEM CONTROL BLOCK DIAGRAM 65 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 17.2. DVD (Servo) : CD HEAD SIGNAL LINE : DVD RF SIGNAL LINE : TRACKING ERROR SIGNAL LINE : DVD HEAD SIGNAL LINE : MOTOR DRIVE SIGNAL LINE : FOCUS ERROR SIGNAL LINE IC8001 MN2DS0018MP IC8251 C0GBG0000048 DV5.0 LSI OPTICAL PICK UP UNIT FP8531 TA(DVD) 21 FP8531 TB(DVD) 20 FP8531 TC(DVD) 18 FP8531 TD(DVD) 19 MOTOR DRIVE 120 VIN1 P4 49 119 VIN2 P3 48 117 VIN3 118 VIN4 TRVFT MUTE SP MUTE PHOTO DETECTOR B1 A1 A2 HEAD A4 A3 AMP B3 SUB1 113 4 B2 B4 27 CH3 MUTE 20 CH4 MUTE 24 FP8531 CH1,2 MUTE 9 LDIN BIAS2 SUB2 114 5 VIN6 DRV0 FP8531 FE1(DVD/CD) 115 16 FP8531 FE2(DVD/CD) 17 67 26 + + 25 FP8531 CH4 - VIN5 116 VIN8 112 VIN9 BIAS1 VHALF 110 1 127 3 PWM0 15 - FP8251 4 LEVEL SHIFT TRIN M TRAVERS MOTOR M SPINDLE MOTOR CH4 VIN7 VO4+ - + + VO4- 16 - FP8251 3 VIN2 - PWM1 126 2 + VCC2-Vf 2 - + + - VIN1 CH3 111 FP8531 RFN 95 13 VIN10 RFINN DRV1 66 23 FP8531 RFP LD+(DVD) 9 + RFINP + FP8531 PIN(DVD) 12 104 LPCO1 103 LPC1 LD+(CD) 11 106 LPCO2 OPIN- LD DRIVE AD1 122 6 - OPOUT PIN(CD) 105 3 HFMON 61 1 5 4 CH1 P14 14 FP8531 - FP8251 LPC2 ACTUATOR TRACKING COIL 18 + OPIN+ FP8531 2 VCC2-Vf 2 Q8561,Q8562 FP8531 VO3- - LD DRIVE - FP8251 CH3 Q8551,Q8552 FP8531 LASER DIODE (CD) 96 14 17 LEVEL SHIFT VIN3 LASER DIODE (DVD) VO3+ + VO1+ LEVEL SHIFT T+ 26 CH1 FP8531 T- 13 23 FOCUS COIL + VO1- - CH2 FP8531 F+ 12 25 FP8531 + VO2+ LEVEL SHIFT F- 24 CH2 QR8571 FP8531 22 HFM SUPPLY CONTROL SWITCH 11 + VO2- - D+3.3V VCC1 2 SA-PT150GC/GCP/GCS/GCT/GS DVD (SERVO) BLOCK DIAGRAM 66 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 17.3. DVD (Audio) : DVD RF SIGNAL LINE : DVD AUDIO SIGNAL LINE : MAIN SIGNAL LINE : USB SIGNAL LINE IC8421 C0FBBK000050 IC8001 MN2DS0018MP AUDIO DAC DV5.0 LSI OPTICAL PIC-UP UNIT FP8531 RFN 13 FP8531 RFP 14 FP8531 TA(DVD) 21 FP8531 TB(DVD) 20 FP8531 TC(DVD) 18 FP8531 TD(DVD) 19 95 96 97 98 RFINN RFINP VN1RF SRCK 149 7 LRCK 150 8 DRV3 64 11 DRV4 63 12 DRV5 62 13 ADOUT 151 6 BCK DATA2 DATA3 SERIAL INPUT I/F DATA4 VN3RF 100 VN4RF 4X/8X OVERSAMPLING DIGITAL FILTER WITH FUNCTION CONTROLLER 2 STB DAC 215 P11 58 3 P10 57 4 OUTPUT AMP AND LOW-PASS FILTER V OUT1 DAC OUTPUT AMP AND LOW-PASS FILTER V OUT2 DAC OUTPUT AMP AND LOW-PASS FILTER V OUT3 DAC OUTPUT AMP AND LOW-PASS FILTER V OUT4 DAC OUTPUT AMP AND LOW-PASS FILTER V OUT5 DAC OUTPUT AMP AND LOW-PASS FILTER V OUT6 DAC OUTPUT AMP AND LOW-PASS FILTER V OUT7 DAC OUTPUT AMP AND LOW-PASS FILTER V OUT8 DVD MIX L 27 FP8101 CN2001 39 DVD MIX R 26 FP8101 CN2001 37 DVD FL 22 FP8101 CN2001 35 DATA1 VN2RF 99 DAC LRCK ENHANCED MULTI-LEVEL DELTA-SIGMA MODULATOR MD FP8101 CN2001 33 TO AUDIO MS MC DVD FR 21 FUNCTION CONTROL I/F DVD SL 20 FP8101 CN2001 31 DVD SR 19 FP8101 CN2001 29 DVD CNT 16 FP8101 CN2001 27 SUBW 15 FP8101 CN2001 25 SYSTEM CLOCK 5 DACCK 148 SCK SYSTEM CLOCK MANAGER ZERO2 ZERO DETECT ZFLAG 28 FP8101 CN2001 23 TO SYSTEM CONTROL IC9003 C0JBAB000908 INVERTER GATE 1 X9004 IC8651 RFKWMHC0B320...GC/GCP/GS RFKWMHC0D320...GCS/GCT QR8420 6 3 4 FG 50 P5 71 A MUTE MUTING 32M FLASH MEMORY DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DATA ADDRESS 29 31 33 35 38 40 42 44 30 32 34 36 39 41 43 45 215 1 3 7 9 11 13 17 216 2 4 8 10 12 14 18 EDT0 EDT1 EDT2 EDT3 EDT4 EDT5 EDT6 EDT7 EDT8 EDT9 EDT10 EDT11 EDT12 EDT13 EDT14 EDT15 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 25 24 23 22 21 20 19 18 8 7 6 5 4 3 2 1 48 17 16 9 10 212 42 41 40 39 38 37 36 29 28 27 26 25 24 23 22 21 35 34 30 45 EXADT0 EXADT1 EXADT2 EXADT3 EXADT4 EXADT5 EXADT6 EXADT7 EXADT8 EXADT9 EXADT10 EXADT11 EXADT12 EXADT13 EXADT14 EXADT15 EXADR16 EXADR17 EXADR18 EXADR19 EXADR20 XWE XCE XOE XRST 11 26 28 12 31 213 214 70 NEXWE NEXCE NEXOE NRST IC9005 C0DBZYE00002 D+5V DATA P13 60 DRV2 65 FP8101 CPU CLOCK AND GATE TO/FROM DVD INTERFACE 1 2 FP8101 CPU STATUS 1 CN2001 FP8101 2 CPU CMD AND GATE 4 1 2 EN 5 OC OUT 8 OUT 7 OUT 6 FP9001 CN8003 CN8002 CN8000 CN8001 1 5 5 5 1 D- FP9001 CN8003 CN8002 CN8000 CN8001 2 4 4 4 2 D+ FP9001 CN8003 CN8002 CN8000 CN8001 3 3 3 3 3 VBUS OUT 64M SDRAM 55 P8 IC8695 C0JBAA000502 CN2001 IN IN 4 IC8051 C3ABPG000145 ADDRESS MEMORY ADDRESS 4 USB OVER 2 3 ROUT 146 IC8691 C0JBAA000502 3 USB VBUS LOUT 144 MEMORY DATA CN2001 USB RECEPTACLE REGULATOR MDQ0 MDQ1 MDQ2 MDQ3 MDQ4 MDQ5 MDQ6 MDQ7 MDQ8 MDQ9 MDQ10 MDQ11 MDQ12 MDQ13 MDQ14 MDQ15 160 162 164 168 170 172 176 178 177 175 171 169 167 163 161 159 2 4 5 7 8 10 11 13 42 44 45 47 48 50 51 53 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 MEMORY DATA MA0 MA1 MA2 MA3 MA4 MA5 MA6 MA7 MA8 MA9 MA10 MA11 (DQM3) 201 203 207 209 208 206 202 200 198 194 199 192 23 24 25 26 29 30 31 32 33 34 22 35 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 MEMORY ADDRESS 190 189 188 181 185 19 18 17 16 38 NCS NRAS NCAS NWE CLK NCSM NRAS NCAS NWE MCK 54 P7 53 P6 SA-PT150GC/GCP/GCS/GCT/GS DVD (AUDIO) BLOCK DIAGRAM 67 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 17.4. DVD (Video) : DVD VIDEO SIGNAL LINE : MAIN SIGNAL LINE IC2801 C9ZB00000461 IC8001 MN2DS0018MP VIDEO BUFFER DV5.0 LSI IC2802 C1AB00001731 DAC1 OUT 131 Q8331 BUFFER Y/PY/G FP8101 CN2001 11 49 10 DAC2 OUT 130 Q8335 BUFFER CB/PB/B FP8101 CN2001 13 47 BIAS H CLAMP L VIDEO BUFFER CY IN 6dB 12 MHz LPF 75 CY SAG SEL CB IN CY OUT BIAS 12 MHz LPF 6dB 75 CB OUT CB SAG DAC3 OUT 129 Q8341 BUFFER CR/PR/R FP8101 CN2001 15 45 CR IN BIAS 12 MHz LPF 6dB 75 CR OUT CR SAG 7 DAC4 OUT 138 Q8321 BUFFER Y FP8101 CN2001 8 43 Q2801 MUTING MUTING 5 14 DAC5 OUT 139 OSCI Q8325 BUFFER C 155 X8621 OSCO FP8101 CN2001 41 IC8601 C0EBA0000029 IC8606 C0EBE0000456 RESET RESET 156 OUT 1 1 4 23 6 4 IN1 IN2 OUT 2 JK2001 Y(RED) 1 SW 21 JK2001 PB(GREEN) 20 18 JK2001 PR(BLUE) 17 SEL Y IN CLAMP 6 MHz LPF 6dB 75 Y OUT Y SAG 6 24 CV IN 26 H CLAMP 6dB 6 MHz LPF + MUTE 1 75 V OUT L V SAG MUTE 2 C IN 27 BIAS 6dB 6 MHz LPF 75 C OUT 30 JK2001 VIDEO OUT 29 32 OUT 1 NRST 70 IC8611 16M EEPROM ( Not Supplied) P1 46 P2 47 SDA SCL 5 SDA 6 SCL RGB FROM SYSTEM CONTROL VIDEO MUTE SA-PT150GC/GCP/GCS/GCT/GS DVD VIDEO BLOCK DIAGRAM 68 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 17.5. Audio :FM SIGNAL LINE :MAIN SIGNAL LINE :AUX, MIC SIGNAL LINE IC2102 C1AB00002463 AUDIO SIGNAL PROCESSOR JK1001 21PIN JACK LINEOUT L 3 LINEOUT R 1 TV LCH 6 TV RCH 2 100 99 92 91 RECOUTL AMP RECOUTR INL3 INR3 TONE 88 TUNER PACK 87 CN2010 CP2010 CN2002 TUN L-CH 5 CN2010 CP2010 CN2002 TUN R-CH 7 JK2002 AUX L AUX L-CH AUX R-CH JK2002 AUX R FP8101 CN2001 MIX L MIX R DVD FL 35 FP8101 CN2001 DVD FR 33 FP8101 CN2001 FROM DVD (AUDIO/ VIDEO) DVD SL 31 FP8101 CN2001 90 89 95 37 FP8101 CN2001 93 96 39 FP8101 CN2001 94 DVD SR 29 84 83 81 80 DVD CNT FP8101 CN2001 82 27 INL5 FLSEL OUT INR5 FRSEL OUT 13 14 22 21 FLVOL IN FLVOL OUT FRVOL IN FRVOL OUT INL2 79 25 40 26 27 17 FRONT L 18 FRONT R AMP INR1 FL IN FR IN SL IN SLSEL OUT AMP SR IN SRSEL OUT 35 34 36 37 SLVOL IN SRVOL IN SLVOL OUT AMP SRVOL OUT SLF IN SL OUT SRF IN SR OUT 30 SURROUND L 41 SURROUND R TO AMP & POWER C IN CSEL OUT 23 24 CVOL IN CVOL OUT CF IN C OUT 28 CENTER SUB IN SUBSEL OUT 53 H BASS 52 SUBVOL IN AGC SUBOUT AMP 46 64 MCU I/F DATA 65 ASP DAT 31 39 FR OUT INL1 AMP ASP CLK 32 FL OUT INR4 CLOCK FROM SYSTEM CONTROL 19 AMP INL4 AMP FP8101 CN2001 16 20 INR2 AMP DVD SUBW 15 48 ASS OP IN 1 47 97 MIC IN AMP AMP OP OUT 1 OP IN 2 46 OP OUT 2 AMP 45 44 SUBWOOFER Q3009 MUTING Q3003 FROM SYSTEM CONTROL IC7100 C1BB00001061 BUFFER MUTE C Q3008 MUTING DIGITAL DELAY WITH ECHO VOLUME 20KBIT SRAM 7 IC2204 C0ABBB000230 IC7101 C0ABBB000230 6 MIC AMP MIC AMP VR6081 1 XM AOUT L 1 _ + LPF2OUT 2 9 LPF2 MAIN CONTROL D/A 3 LPF1IN A/D LPF1 ASP MICIN 2 H6903 CN2006 1 1 _ + 2 7 3 + _ JK6802 5 2 MIC 6 3 XM AOUT R MIC SW 4 Q7100 ECHO MUTE 5 MUTING OSC Q7102 ECHO LV1 FROM/TO SYSTEM CONTROL AUTO RESET SWITCH Q7101 ECHO LV2 MIC SW SWITCH CN2006 H6903 7 SA-PT150GC/GCP/GCS/GCT/GS AUDIO BLOCK DIAGRAM 69 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 17.6. Amp & Power :MAIN SIGNAL LINE IC5100 AN17831A SPEAKERS POWER FRONT L + FRONT L 8 CH2 INPUT CH2 + OUTPUT _ _ FR0NT +L FRONT +LOUT 12 FRONT -LOUT JK5000 + 4 JK5000 +26V 1 VCC _ + CH2 OUTPUT FRONT R FRONT -L FRONT +ROUT JK5000 FRNOT -ROUT JK5000 6 CH1 INPUT _ _ _ + MUTE +1.2V REGULATOR SURROUND +LOUT JK5000 SURROUND -LOUT JK5000 +1.2V 2 QR8111 POWER CONTROL - 12 SURROUND R SURROUND +ROUT JK5000 STANDBY CIRCUIT SURROUND -ROUT D+5V + 5 JK5000 - A+5V SW5V IC5200 AN17831A CENTER POWER M+9V CENTER+ JK5000 + 2 + 8 VCC + 11 SURROUND L OUT 4 REF 5 4 + MUTE STANDBY FROM AUDIO IC8151 C0DBEHG00006 2 FRONT -R 8 5 SURROUND L CH1 OUTPUT VIN CONT FRONT +R 6 9 1 V0 - 9 FRONT R +3.3V + 3 7 GND CH1 + OUTPUT +3.3V DC-DC CONVERTER 10 + + IC8111 C0CBCBD00018 - 10 CH2 INPUT CH2 + OUTPUT _ _ CENTERSURROUND +L JK5000 +9.1V - 8 12 D2918 +26V 1 VCC _ + CH2 OUTPUT SUBWOOFER+ JK5000 SUBWOOFER- JK5000 6 CH1 INPUT _ _ Q2905 - 7 SURROUND R DC DETECT DC DET1 + 1 7 GND CH1 + OUTPUT Q2910 SURROUND -L 10 + + TO SYSTEM CONTROL SUBWOOFER POWER SUPPLY DC DETECT SURROUND +R 2 IC2903 AN30071A-NM Q2914, D2944 _ + FROM SYSTEM CONTROL 9 MUTE F SW MUTE CH1 OUTPUT SURROUND -R DVD 2.7V REGULATOR DVD 2.7V 4 + REF Q2974, D2974 -VP REGULATOR -VP + CH2 INPUT CH2 + OUTPUT _ _ 1 VCC _ + FROM AUDIO D2007 12 1 SYS6V VREF+ CH2 OUTPUT CH1 INPUT CH1 + OUTPUT _ _ SUBWOOFER + 2 FAN Q5741 _ + 9 MUTE + MUTE REF STANDBY STYB 5 STANDBY CIRCUIT CH1 OUTPUT 2 SYNC SYNC FROM/TO SYSTEM CONTROL DC DET2 MUTE FRONT 7 PCONT TO SYSTEM CONTROL + FROM SYSTEM CONTROL 10 VCC CTRL PCONT + 6 TO SMPS MODULE P.C.B. CENTER 10 7 GND SUBWOOFER 11 -VP (-21V) SYS6V CENTER + VCC CTRL +26V 4 +9.1V -7V REGULATOR -7V POWER 8 VCC 2 Q2906,Q2907 STANDBY CIRCUIT IC5300 AN17831A CENTER 3 LX(OUT) MUTE STANDBY 5 H2002 DC-DC CONVERTER SUBWOOFER 4 FAN LOCK DETECT Q5740, Q5742, Q5744 FAN MOTOR DRIVE FAN LOCK CN6001 CN2007 8 CN5704 FAN DC OUT CN5704 FAN GND CN5704 1 FL1 (FL+) 8 CN6001 CN2007 3 6 6 FL2 (FL-) 8 FL1 (FL+) 9 FL2 (FL-) H2001 M 2 +26V Q5745 FAN DC SUPPLY 1 +26V (VCC) 2 +26V (VCC) Q5746 INVERTER SA-PT150GC/GCP/GCS/GCT/GS AMP & POWER BLOCK DIAGRAM 70 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 18 Schematic Diagram Notes : DVD Video signal line : CD Head signal line · This schematic diagram may be modified at any time with the development of new technology. : DVD Head signal line Notes: S901: S902: S6800: S6801: S6802: S6803: S6804: S6805: S6806: VR6081: VR6800: Play switch. Open switch. AC IN). Power switch ( Open / Open / close switch ( Close). / / Forward switch ( TUNING ). / / Reverse switch ( TUNING ). / -TUNE MODE / — Stop switch ( FM MODE). / Memory). Play switch ( Selector switch. Mic Volume. Volume jog. : Main signal line : Tracking Error signal line : Focus Error signal line : FM signal line : AUX/MIC signal line · Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (highimpedance) with the chassis taken as standard. Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester. · Important safety notice: mark Components identified by characteristics important for safety. have special Furthermore, special parts which have purposes of fireretardant (resistors), high-quality sound (capacitors), lownoise (resistors), etc. are used. When replacing any of components, be sure to use only manufacturer´s specified parts shown in the parts list. · Resistor Unit of resistance is OHM [Ω] (K=1,000, M=1,000,000). · Capacitor Unit of capacitance is µF, unless otherwise noted. F=Farad, pF=Pico-Farad · Coil Unit of inductance is H, unless otherwise noted. · Voltage and signal line : +B signal line : -B signal line : USB signal line : DVD RF signal line : Motor Drive signal line : DVD Audio signal line 71 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 72 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 19 Schematic Diagram 19.1. DVD Module Circuit MDQ_3 MDQ_12 MDQ_2 MDQ_13 MDQ_5 MDQ_10 MDQ_4 MDQ_11 8 6 4 2 RX8012 D1H88204A024 0.1 RX8013 D1H88204A024 DQM1 DQM0 CLK NWE 22 NRAS NCAS R8012 NCSM 22 7 5 3 1 C8015 LB9001 J0JCC0000119 7 5 3 1 8 6 4 2 0.1 C9005 7P 7 5 3 1 8 6 4 2 C8014 R9009 1K RX8019 D1H422020001 MDQ_7 MDQ_8 RX8014 D1H88204A024 MDQ_6 MDQ_9 4 1 7 5 3 1 0.1 3 R8011 22 13 14 A75 8 6 4 2 C8013 4 4 2 0.1 2 2A 3 1 C8003 GND 2Y R8013 RX8018 D1H422020001 VC 4 2 0.1 5 R9008 1M 3 1 C8012 1 4 2 RX8015 D1H88204A024 1A 3 1 0.1 1Y 7 5 3 1 RX8017 D1H88204A024 D+ DVBUS_OUT 6 7 5 3 1 8 6 4 2 8 6 4 2 C8016 VBUS 3 2 7 5 3 1 8 6 4 2 12 : USB SIGNAL LINE 0.1 5 5 4 3 2 1 X9004 H1A4805B0027 USB RELAY CIRCUIT (CN8003) IN SCHEMATIC DIAGRAM - 10 DGND DGND D+ D- MA_1 MA_6 MA_0 MA_7 C9004 7P RX8020 D1H422020001 TRV_INNER_SW : TRACKING ERROR SIGNAL LINE BA1 BA0 : DVD VIDEO SIGNAL LINE MA_9 : MOTOR DRIVE SIGNAL LINE MA_11 : DVD HEAD SIGNAL LINE MA_10 MA_8 : FOCUS ERROR SIGNAL LINE INVERTER GATE FP9001 11 : DVD AUDIO SIGNAL LINE IC9003 C0JBAB000908 1 10 : DVD RF SIGNAL LINE C9007 0.1 TO G 9 : CD HEAD SIGNAL LINE RX8016 D1H88204A024 : +B SIGNAL LINE 8 MDQ_0 MDQ_15 SCHEMATIC DIAGRAM - 1 DVD MODULE CIRCUIT B 7 MDQ_1 MDQ_14 6 RX8011 D1H88204A024 5 MA_4 MA_2 MA_5 4 MA_3 3 CKE A 2 C8004 1 TO DVD MODULE SECTION (2/4) LB8001 J0JHC0000045 A76 A77 EXADR_0 EXDT8 EXDT0 73 C8306 0.1 A81 155 C8026 154 153 R8401 151 150 149 148 147 146 145 A82 0.1 C8401 15P 100 RX8401 1 D1H410120001 3 LB8401 2 4 DMIXOUT LRCK 3R3_L8420 A84 A85 A86 A87 144 143 C8305 C8304 142 141 0.1 0.1 A80 C8302 6.3V33 A88 140 A89 139 A90 138 136 135 134 133 A91 C8301 6.3V220 C8313 1 R8313 15K C8312 1 R8314 15K A92 A93 C8303 132 0.1 A94 A95 131 A96 130 129 C8202 128 C8203 0.1 A97 0.1 127 126 122 R8541 121 VIN1 VIN2 VIN4 VIN3 VIN8 VIN7 VIN6 VIN5 120 119 118 117 116 115 114 113 C8225 1000P 124 15K R8221 8.2K C8541 4700P C8221 1000P FODRV C8222 1000P R8225 8.2K 125 TRDRV C8226 820P D8211 MA2J11100L C8211 1200P 112 R8211 10K A64 A62 A63 VREFH 110 VHALF 111 109 A83 SRCK ADAC-CLK J0JBC0000042 C8429 0.1 A61 A58 A57 0.1 156 123 A56 C8005 157 AD2 AD1 AD0 VIN1 VIN2 VIN4 VIN3 VIN8 VIN7 VIN6 VIN5 VIN9 VIN10 VHALF VREFH A55 A54 A53 A52 A51 A50 A49 158 137 [108]AVSSB A48 A1 TO DVD MODULE SECTION (3/4) 159 AVSSF COMP2 IREF1 VREF COMP1 AVDDF DAC1OUT DAC2OUT DAC3OUT AVDDH PWM0 PWM1 AVSSH AD4 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100101102103104 105106107108 H 160 A60 MDQ3 MDQ12 VDD33 VSS DQM1 DQM0 MDQ7 MDQ8 MDQ6 MDQ9 VDD33 VSS MDQ5 MDQ10 MDQ4 MDQ11 MCK VSS NWE DQM2 NCSM NRAS NCAS VDD12 VSS MCKI VDD33 MA8 BA1 VDD33 VSS MA9 BA0 DQM3 EXADT0 VDD12 VSS MA3 MA4 MA2 MA5 VDD33 VSS MA1 MA6 MA0 MA7 MA10 152 [107]AVDDB [55]P8 [56]P9 P10 P11 CPU-CMD CPU-STAT IECOUT ADOUT LRCK SRCK DACCK AVDDI ROUT AVSSI LOUT AVSSG AVDDG AVDDE AVSSE DAC5OUT DAC4OUT 161 A59 C8022 0.1 162 LPC1 LPCO1 LPC2 LPCO2 SP_MUTE A47 A15 1 EXADR_15 A46 48 A16 R8002 10K EXADR_14 A45 A14 2 EXADR_20 ANAMONI1 ANAMONI2 RFINN RFINP VIN1RF VIN2RF VIN4RF VIN3RF VREFH5 VREFL5 47 XBYTE EXADR_16 EXADR_13 0.1 A44 A13 3 C8007 A43 46 VSS G EXADR_12 A42 A12 4 A41 A11 5 DQ15/ 45 A-1 A40 44 DQ7 VREFL7 AVSSC CCAPA CDATA AVDDC EXDT7 EXDT15 EXADR_11 EXADR_3 EXADR_2 EXADR_1 A39 A10 6 A38 43 DQ14 EXADR_9 EXADR_10 A37 A9 7 A36 42 DQ6 EXADR_18 EXADR_17 EXADR_7 EXADR_6 EXADR_5 EXADR_4 A35 A8 8 EXADR_8 0.1 A34 41 DQ13 C8021 A28 A19 9 XWE A27 EXDT14 40 DQ5 EXADR_20 A26 0.1 EXDT6 C8652 EXDT13 A20 10 DV5.0 LSI SDATA EXTRG0 EXTRG1 TRCCLK TRCDATA0 TRCDATA1 TRCDATA2 TRCDATA3 TRCST VSS VDD12 AVDDD PLFIL1 VREFH7 AVSSD EXDT5 39 DQ12 XWE IC8001 MN2DS0018MP EXADT11 EXADT10 EXADT9 EXADT8 EXADR19 NEXWE VSS VDD33 EXADR18 EXADR17 EXADT7 EXADT6 38 EXADT5 39 EXADT4 40 EXADT3 41 EXADT2 42 EXADT1 43 VSS 44 VDD12 45 P0 46 P1 47 P2 48 P3 49 P4 50 P5 51 VSS 52 VDD33 53 P6 54 P7 26 27 28 29 30 31 32 33 34 35 36 37 A25 F XWE 11 EXADR_11 EXADR_10 EXADR_9 EXADR_8 A24 EXDT12 38 DQ4 XRESET R9080 10K A23 37 VDD XRESET 12 EXDT4 EXADR_12 NC 13 A22 36 DQ11 R9040 10K A21 WP/ 14 ACC EXADR_16 EXADR_15 EXADR_14 EXADR_13 A20 35 DQ3 0.1 A19 RDY/ XBSY 15 C8006 A18 34 DQ10 EXDT7 EXDT15 EXADR_18 A17 A18 16 0.1 A16 33 DQ2 A17 17 C8020 EXADR_17 A15 32 DQ9 EXADR_7 A14 A7 18 A13 31 DQ1 EXDT5 EXDT13 EXDT6 EXDT14 EXADR_6 A12 A6 19 EXADR_5 MDQ1 MDQ14 MDQ0 MDQ15 VDD12 VSS OSCO OSCI VDD33 VSS [163]MDQ13 [164]MDQ2 [216]EXDT8 A11 EXDT11 30 DQ8 EXDT12 A9 EXDT3 A5 20 EXDT4 A8 EXDT10 29 DQ0 EXDT3 EXDT11 EXADR_4 A79 [215]EXDT0 A10 EXDT9 EXDT2 C8651 E A4 21 0.1 A7 0.1 EXDT1 28 XOE EXDT1 EXDT9 EXDT2 EXDT10 VSS VDD33 EXDT3 EXDT11 9 EXDT4 10 EXDT12 11 EXDT5 12 EXDT13 13 EXDT6 14 EXDT14 15 VSS 16 VDD33 17 EXDT7 18 EXDT15 19 VSS 20 VDD12 21 EXADR16 22 EXADT15 23 EXADT14 24 EXADT13 25 EXADT12 A6 EXDT8 A3 22 C8018 EXADR_3 A5 EXDT0 27 VSS EXADR_2 1 2 3 4 5 6 7 8 A4 D A2 23 EXADR_1 A3 26 XCE A1 24 A2 25 A0 A78 216215214213212211 210209208207206205204203202201200199198197 196195194193192191190189188187186185184183182181180179178177176175174173172171170169168167166165164163 EXDT1 EXDT9 EXDT2 EXDT10 P12 P13 P14 DRV5 DRV4 DRV3 DRV2 DRV1 DRV0 VSS VDD33 NRST FG SCLOCK 32M FLASH MEMORY NEXOE NEXCE IC8651 RFKWMHC0B320...GC/GCP/GS RFKWMHC0D320...GCS/GCT C8001 4V330 R9042 10K C C8011 6.3V100 LB8011 J0JHC0000045 1/4 2/4 3/4 4/4 SA-PT150GC/GCP/GCS/GCT/GS DVD MODULE CIRCUIT SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 15 16 17 18 19 20 21 22 23 24 25 26 27 28 SCHEMATIC DIAGRAM - 2 DVD MODULE CIRCUIT : DVD AUDIO SIGNAL LINE : +B SIGNAL LINE : DVD VIDEO SIGNAL LINE : USB SIGNAL LINE : MAIN SIGNAL LINE FP8101 TO DVD MODULE SECTION (1/4) IC8421 C0FBBK000050 C8402 0 EN 2 3 4 R9043 IN 1 C9006 0.1 R8421 15P 1 ZERO1 ZERO2 28 2 MS VOUT1 27 3 MC VOUT2 26 VCOM 25 4 MD AGND2 24 5 SCK 6 DATA1 VCC2 23 7 BCK VOUT3 22 8 LRCK VOUT4 21 VDD VOUT5 20 9 10 DGND VOUT6 19 11 DATA2 AGND1 18 VCC1 17 12 DATA3 13 DATA4 VOUT7 16 14 MSEL VOUT8 15 0 RX8403 D1H410120001 4 2 3 1 AOUT0 AOUT1 C8426 0.1 AOUT2_1 C8422 0.1 Y LB8301 J0JBC0000042 C LB8302 J0JBC0000042 R8420 2.2K MUTING D- R8325 200 Q8325 2SB1218ARL R8324 1K Q8321 2SB1218ARL BUFFER LB8430 J0JHC0000045 R8334 1K 2 3 5 21 20 19 18 17 16 15 14 13 12 11 10 9 D E F A+5V LB8690 J0JBC0000044 C8152 1 AND GATE DGND CPU-CLK 1 VCC 5 3 GND G 4 IC8695 C0JBAA000502 C8341 0.1 AND GATE CPU-STAT TO DVD MODULE SECTION (4/4) 1 VCC 5 2 3 GND A73 A72 A71 A70 A69 BUFFER AUDIODIGTAL D+5V D+5V DGND D+5V DGND A+5V AGND A+5V AGND 2R7V DGND 2R7V 8 DGND 7 M+9V 6 MGND 5 M+9V 4 MGND 3 DOP_CPU-CLK 2 DOP_CPU-CMD 1 DOP_CPU-STAT IC8691 C0JBAA000502 33 Q8341 2SB1218ARL ERJ2GEJ101X ERJ2GEJ101X ERJ2GEJ101X LB8691 LB8693 LB8692 C TO MAIN CIRCUIT (CN2001) IN SCHEMATIC DIAGRAM - 6 R8154 1K C R8341 200 A66 A65 A97 ERJ2GE0R00X BUFFER R8342 A96 ERJ2GE0R00X LB8491 C C8320 0.1 Q8335 2SB1218ARL R8343 1K A95 ERJ2GE0R00X LB8424 2 33 R8312 1K A94 LB8423 C8335 0.1 A68 C8311 0.1 C8151 4.7 Y_PY_G 2.4K 4 BUFFER R8336 A93 C8330 6.3V47 Y R8311 G1C100K00019 R8335 200 A92 L8301 C8331 0.1 Q8331 2SB1218ARL R8337 1K 3R3_L8301 ERJ2GE0R00X ERJ2GE0R00X 33 A89 A91 LB8429 LB8431 AGND 2R7V CR_PR_R L8302 G1C100K00019 ERJ2GE0R00X +1.2V REGULATOR VCC GND OUT ADJ 1 R8153 620 CB_PB_B R8332 0 A80 R8331 200 R8333 0 A87 A90 CTL L8330 R8424 LB8428 B IC8151 C0DBEHG00006 C8340 0.1 G1C100K00019 A86 A88 33 C8321 0.1 C8430 6.3V47 A85 3R3_L8302 R8321 200 R8322 0 24 R9033 A84 R9032 24 A83 ERJ2GE0R00X CPU-CMD BUFFER R8323 ERJ2GE0R00X LB8427 FL8104 F1J1E1040022 33 R8327 R8326 0 R9045 0 R9035 15K R9044 0 D+ ERJ2GE0R00X LB8426 C8325 0.1 A5V_L8330 X8621 H0J270500085 R9034 15K R8328 1K R8621 1M A82 LB8425 FL8101 F1H0J1050018 A81 C8621 12P ERJ2GE0R00X FL8102 F1H0J1050018 QR8420 UNR521100L AMUTE ERJ2GE0R00X LB8422 FL8103 F1H0J1050018 D+5V AMUTE C8622 12P LB8421 0 C8427 0.1 A77 R8622 680 J0JBC0000042 C8424 0.1 VCC_LB8001 A76 J0JBC0000042 LB8305 C8423 6.3V33 R9036 10K R9037 10K C9008 1 A78 A79 C8428 0.1 USB_OVER USB_VBUS LB8304 CR_PR_R VGND Y/PY/G VGND CB/PB/B VGND CR/PR/R VGND Y VGND C ADAC5V MIX-L ADAC5V 37 MIX-R 36 ADGND 35 FL 34 ADGND 33 FR 32 ADGND 31 SL 30 ADGND 29 SR 28 ADGND 27 CNT 26 ADGND 25 SW 24 A-REF 23 ZFLAG&AMUTE 22 D+5V 50 49 48 47 46 45 44 43 42 41 40 39 38 0.1 FLG OUT GND REGULATOR SBT3 SBO3 ADAC-CLK DMIXOUT SRCK LRCK CB_PB_B AUDIO DAC IC STBDAC 5 IN IC9005 C0DBZYE00002 6 OUT 7 OUT 8 J0JBC0000042 C8691 VBUS_OUT 0.1 LB8303 74 A74 C9018 K8421 C8421 6.3V100 Y_PY_G A67 A75 A C8695 0.1 4 1/4 2/4 3/4 4/4 SA-PT150GC/GCP/GCS/GCT/GS DVD MODULE CIRCUIT H SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS SCHEMATIC DIAGRAM - 3 L 3 A2 SCL 6 4 GND SDA 5 4 2 3 1 R8611 100 0.015 WP 7 C8602 VCC 8 A1 OUT 1 NC CD OUT VDD VSS N LPC2 MA_6 MA_7 R8232 7.5K MA_8 MA_9 MA_11 C8232 0.1 CKE SP_DRV 1 A63 A62 A61 VDD33 VDD 27 A3 26 30 A5 A2 25 MDQ_8 C8056 2200P 1 MDQ_9 RESET MDQ_10 MDQ_11 MDQ_12 C8057 1 O MDQ_13 MDQ_14 A1 24 A0 23 33 A8 A10/AP 22 34 A9 BA1 21 BA1 BA0 20 BA0 35 A11 39 UDQM P NRAS NCAS NWE /WE 16 LDQM 15 42 DQ8 DQ7 13 DQM0 C8054 220P MDQ_7 VSSQ 12 44 DQ9 DQ6 11 45 DQ10 DQ5 10 46 VSSQ VDDQ 9 47 DQ11 DQ4 8 48 DQ12 DQ3 7 MDQ_6 MDQ_5 C8053 0.1 MDQ_4 MDQ_3 VSSQ 6 50 DQ13 DQ2 5 51 DQ14 DQ1 4 53 DQ15 DQ0 2 54 VSS VDD 1 C8051 NCSM /CAS 17 VDD 14 49 VDDQ MA_10 /CS 19 41 VSS 43 VDDQ MA_0 /RAS 18 52 VSSQ VDDQ 3 MDQ_15 MA_2 MA_1 32 A7 38 CLK C8606 0.1 MA_3 31 A6 40 NC 2 1 29 A4 37 CKE CLK TO DVD MODULE SECTION (4/4) 64M SDRAM 36 NC TRV_DRV 3 A64 A60 C8528 0.1 C8504 1 1 1 0.1 0.1 0.1 0.1 0.1 0.1 C8512 C8511 C8513 C8514 C8516 C8515 C8521 C8522 MA_5 IC8606 C0EBE0000456 XRESET C8529 5600P 0.018 0.1 C8525 C8526 C8503 R8230 2.2K DQM1 5 IC8051 C3ABPG000145 28 VSS MA_4 RESET 4 A59 A58 A57 A56 A55 A54 A53 0.1 C8524 A104 2 4 LPC1 1 3 IC8601 C0EBA0000029 M A52 A51 A50 A49 A48 A47 A46 A45 A44 A43 A42 A41 A40 A39 A38 A37 A36 A34 A35 0.1 0.033 0.1 C8502 C8527 C8523 A103 R8233 2.2K 4 GND A101 A105 C8231 0.1 VDD 2 A99 A100 RX8032 D1H447220001 0.1 3 NC C8201 6.3V100 A102 R8231 22K C8601 C8501 6.3V100 C8505 0.1 C8055 100K A0 2 RX8611 C8611 0.1 D1H447220001 R8601 1 C8008 IC8611 16M EEPROM IC (NOT SUPPLIED) 0.1 2 1 4 3 RX8402 D1H410120001 C8002 0.1 VIN2 VIN4 VIN3 AOUT1 AOUT0 3R3_L8201 RX8031 D1H447220001 4 3 2 1 VIN1 4 2 A98 L8501 G1C100K00019 RFINN RFINP 3 1 AOUT2_1 K A28 R8041 AMUTE USB_OVER RX8001 D1H410320002 L8201 G1C100K00019 3R3_L8501 R8042 10K RX8691 D1H410320002 2 1 4 3 HFMON STBDAC SBO3 SBT3 DVD_CD USB_VBUS CPU-CLK TO DVD MODULE SECTION (1/4) J A27 A26 33 A24 A23 A22 A21 A20 A19 A18 A17 A16 A15 A14 A13 A12 A9 A8 A10 A25 : DVD AUDIO SIGNAL LINE : DVD RF SIGNAL LINE A7 A6 A5 A2 A1 : MOTOR DRIVE SIGNAL LINE A11 : +B SIGNAL LINE A4 DVD MODULE CIRCUIT A3 I MDQ_2 MDQ_1 C8052 0.1 1/4 2/4 3/4 4/4 MDQ_0 SA-PT150GC/GCP/GCS/GCT/GS DVD MODULE CIRCUIT 1 A106 1 2 3 4 5 6 7 8 75 9 10 11 12 13 14 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS SCHEMATIC DIAGRAM - 4 3 GND GND 6 4 CN RX8111 D1H422320002 2 4 0.1 GND 7 1 3 6 5 4 1 2 3 CONT 5 QR8111 XP0621400L POWER CONTROL L8550 G1C100KA0055 A98 2 GND C8111 D+3R3V C8113 470P TO DVD MODULE SECTION (2/4) VIN 8 1 VO C8112 1 A74 A67 IC8111 C0CBCBD00018 +3.3V DC-DC CONVERTER A73 : FOCUS ERROR SIGNAL LINE A72 : TRACKING ERROR SIGNAL LINE A71 : DVD HEAD SIGNAL LINE A70 : DVD RF SIGNAL LINE A69 : MOTOR DRIVE SIGNAL LINE A68 : +B SIGNAL LINE A66 A65 DVD MODULE CIRCUIT I : CD HEAD SIGNAL LINE J A99 A100 R8265 0 PIN_26 DGND D+5V LD DRIVE R8552 1K Q8562 B1ADGB000008 56 51 R8556 R8557 VIN1 VIN2 R8558 47K M+9V TRVFTMUTE MGND 6 5 R8263 82K R8261 82K QR8571 UNR511V00L D8571 MA2J72800L HFMON Q8552 B1ADGB000008 VIN1 VIN2 VIN4 VIN3 VIN8 VIN7 RFINP RFINN LD DRIVE LPC1 LB8561 VREFH K8001...GCS/GCT 0 LB8531 LB8530 VIN6 VIN5 K8006...GCS/GCT 0 LPC2 DVD_CD C8532 220P 22 21 20 19 18 17 16 15 14 13 12 11 10 9 1 3 5 7 2 4 2 4 J0JBC0000042 R8531 1.5K J0JBC0000042 0.1 C8533 8 7 6 5 4 3 2 1 J0JHC0000045 RX8533 3 R8532 D1H456020001 1 2.2K C8530 R8533 0 L TO SPINDLE / TRAVERSE MOTOR FP8531 26 25 24 23 2 RX8532 4 D1H85604A024 6 8 RX8534 1 D1H456020001 3 C8531 100P RX8531 1 D1H456020001 3 0 FP8251 SPMSPM+ TRVMTRVM+ DGND TRV_INNER_SW C8572 0.1 0 0 0 0 J0JBC0000042 LB8551 A105 4 3 2 1 C8263 220P LB8257 LB8259 LB8260 LB8258 LB8571 Q8552 LD DRIVE C8258 0.1 OPINOPIN+ SUPPLY CONTROL SWITCH Q8551 2SD1819A0L C8257 16V47 R8251 6.8 TRV_INNER_SW R8554 68 K C8254 0.1 SPMUTE 0.1 C8553 6.3V47 R8555 2.2 MGND LDCNT 28 MUTE3 27 TRIN 26 BIAS2 25 OPIN+ LDIN 24 OPINVIN3 23 OPOUT GND 22 [PRE] PREVCC FIN 30 FIN VCC VCC [CH1,2] [CH3,4] 21 MUTE12 MUTE4 20 GND GND [CH1,2] [CH3,4] 19 VO3- 18 VO2VO3+ 17 VO2+ VO4- 16 VO1VO4+ 15 VO1+ BIAS1 R8559 15K R8551 0 A104 C8253 0.1 LD DRIVE 16V10 1K C8554 C8552 R8553 1 R8562 1K C8252 0.1 TRVFTMUTE Q8561 2SD1819A0L C8551 R8561 0 C8251 6.3V220 1 2 3 4 5 6 7 29 8 9 10 11 12 13 14 C8262 0.1 C8571 10 R8264 PIN_23 0 R8564 22 A103 C8261 0.1 PIN_27 SP_DRV TRV_DRV K8251 MOTOR DRIVE C8255 16V22 C8561 R8568 47K 15K 15K C8550 6.3V33 56 51 R8566 R8567 0.1 C8563 6.3V47 R8565 2.2 FODRV TRDRV SP_MUTE 1K C8564 C8562 R8563 1 TO DVD MODULE SECTION (3/4) 16V10 A5V_L8550 IC8251 C0GBG0000048 R8262 A102 C8256 0.1 A101 4 2 0.1 T+ F+ FTHFM TA(DVD) TB(DVD) TD(DVD) TC(DVD) FE2(DVD/CD) FE1(DVD/CD) GND RF VREF2(RF-) PIN(DVD) LDCD LDGND LDDVD GND(OEIC) VREF1 VCC SUB2 SUB1 PIN(CD) SUBSEL M TO OPTICAL PICKUP UNIT CIRCUIT IN SCHEMATIC DIAGRAM - 11 N GND(VRCD) O 1/4 2/4 3/4 4/4 SA-PT150GC/GCP/GCS/GCT/GS DVD MODULE CIRCUIT A106 15 16 17 18 19 20 21 22 76 23 24 25 26 27 28 P SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 19.2. Main Circuit 1 3 4 5 6 7 8 9 10 11 12 13 SCHEMATIC DIAGRAM - 5 :-B SIGNAL LINE C MAIN CIRCUIT :+B SIGNAL LINE :AUX / MIC SIGNAL LINE :MAIN SIGNAL LINE R7107 OP1OUT C7112 0.1 REF 13 C7110 16V47 OP2IN 12 6 CC1 OP2OUT 11 7 CC2 LPF2IN 10 C7109 0.068 R7101 15K C7102 6800P C7104 0.068 R7114 R7113 5.6K 10K 4 R7105 15K R7104 15K C7108 1500P 8 GND LPF2OUT 9 R7103 15K C7120 0.015 0 C7118 0.1 R7112 2.7K 5 V- Q7101 B1GBCFJJ0051 R7109 C7113 50V1 4.7K SWITCH 1 Q7102 B1GBCFJJ0051 SWITCH MIC_AGND C2724 1800P C2624 6800P C2524 6800P FROUT C2183 1 R2185 2200P C2424 2200P 10K FLOUT C2283 SR_OUT C2312 SL_OUT C2412 1 R2285 10K FL_IN 1 R2312 10K 1 R2412 10K SR_IN SL_IN CENTER C2506 1 R2510 15K C3005 1 R2617 22K C3006 50V10 10K 0 C_IN SW_IN R2194 W4026 0 27K C2619 50V10 R2294 W4007 0 27K W4042 0 FR_IN W4043 R2512 56K SUBW R2626 100K 1.8K TO MAIN SECTION (2/4) R2439 56K SR_OUT R2339 56K R2303 R2301 R7120 15K CLOCK 14 LPF1OUT R7106 120K C7107 6800P C7115 220P 31 6 3 C2617 0.15 SUBW 1.2K 68K 10K 32 10K 1 7 3 C7106 0.22 C7111 16V47 VCC 15 5 OP1IN C7105 0.22 C2611 0.012 R2402 C2301 C2303 C2302 0.047 0.033 R2501 6.8K MUTING 8 2 C2324 R2302 1 SLVOLIN 34 SLNFIN 33 CFIN COUT CVOLOUT CNFIN CVOLIN C2501 1 ASP_GND C3 R3006 1K 0.047 C2503 0.047 ASP_GND R3007 27K C2502 R3009 D3001 1K B0ACCK000005 SW+ C+ Q3009 B1ABCF000176 FR+ FL+ MUTING SWC- AGND FR- R3008 10K FL- Q3008 B1ABGC000005 MUTING W7002 0 R3015 56K BUFFER C3009 50V10 R3003 8.2K SL+ Q3003 B1GDCFJJ0047 R3014 56K MUTE_C SR+ C3007 50V10 R3005 22K R2503 6.8K CENTER 1 C2219 0.047 C2221 FROUT C2220 0.039 R2215 10K C2121 0.047 R2115 10K 0.039 C2120 R2502 10K R7100 15K Q7100 B1GBCFJJ0051 C7116 0.1 AGC2 HBASS9 SUBVOLIN SUBSELOUT HBASS8 HBASS7 HBASS6 HBASS4 HBASS3 HBASS2 HBASS1 HBASS5 CSELOUT FRSELOUT FRVOLIN FRVOLOUT FRFIN FROUT FLOUT FLFIN FLVOLOUT FLVOLIN FLSELOUT 1 C2119 4.7K 4700P 0.047 0.22 C2218 R2610 56K 56K C2401 V+ 1 4 R2608 56K R2611 R2627 C2612 3300P 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 0.015 C7114 47P C2607 50V22 R7116 39K R2620 C2606 16V10 C2601 0.022 R2601 47K DGND CLOCK DATA DVDD SF LSIN LCIN RCIN LIN RSIN TBR2 TBR1 TMR2 TTR 0.022 SRVOLIN 37 SRSELOUT 36 SLSELOUT 35 [32]SLVOLOUT [31]SLFIN R2218 C2215 C2216 4.7K R2214 C2217 0.047 TMR1 TBL2 0.22 TML1 8 R2113 C2115 C2116 4.7K R2114 C2117 4700P SRNFIN 38 7 5 6 R2612 C2610 0.47 AGND 42 R2403 10K SROUT 41 C2403 C2402 SRFIN 40 R2401 1.8K 0.047 0.033 SRVOLOUT 39 [99]RECOUTR [100]RECOUTL TBL1 TTL 4 TML2 CLPF 3 0.015 AGND 2 0.022 C2195 1 C2295 1 12K 470P C2112 R2112 1 49 OPOUT2 44 AGND 43 AUDIO SIGNAL PROCESSOR C7103 1500P W2202...GC/GS -7V R2607 C2605 10K 0.047 C2608 48 16V10 C2609 0.22 OPIN1 47 SLOUT [MIX RCH] [MIX LCH] R2609 1.5K SL_OUT 95 INR1 96 INL1 50 2 LPF1IN R7102 15K MIC AMP OPIN2 45 IC2102 C1AB00002463 FLOUT +9.1V DGND AGND_D R2621 39K 12K W4047 0 C2408 0.022 0.082 C2309 C2304 16V10 12K C2307 16V10 10V1 10V1 R2304 C2306 LF RF RIN EXTOUTR AGND [TUNER RCH] [TUNER LCH] 99 W4096 0 12K 470P C2212 R2212 3.3K 1000P C2165 R2165 1000P C2265 3.3K R2265 6.8K 100P C2272 R2291 6.8K 100P DVD-FL R2191 93 INR2 94 INL2 100 DVD-FR C2172 [TV RCH] [TV LCH] [AUX LCH] 97 MICIN 98 AGND C6921 220P R6921 2.2K C6920 R6920 1 100 [AUX RCH] 91 INR3 92 INL3 C2214 TUN-LCH MIXR 89 INR4 90 INL4 C2118 10K 4.7K 10K ASP_MICIN_1 IC7101 C0ABBB000230 OPOUT1 46 88 INL5 ASP_MICIN G 10K C7101 50V1 C7119 50V2.2 1 MIC_ECHO_OUT [50]AGC1 [49]SUBC [48]SUBOUT 87 INR5 MIXL F C2406 0 +7V TUN-RCH E [81]SLIN [82]CIN 85 AVEE 86 AVCC D2001 AUX_RCH R2164 AUX_LCH R2264 +7V AGND D2002 SRIN 83 FRIN 84 FLIN -7V EXTOUTL 16V47 C2020 0.01 C2019 82 SUBIN 81 R2960 6.8 R2606 ASP_MICIN 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 DVD-CNT D2001 - D2002 B0EAKM000117 12K W4049 C2615 2200P C2507 470P R2619 20K R2511 12K 16V47 W4028 0 W4034 0 C2114 DVD-SL C2017 0.01 C2018 C2423 100P C2323 100P R2336 12K R2436 12K DVD-SR R2404 DVD-SUBW 0.022 3300P 3300P C2405 C2404 16V10 C2407 16V10 R2952 8.2 C C2024 220P 1.8K C2305 W4048 0 TUN+9V C2023 220P DIGITAL DELAY WITH ECHO VOLUME NC 16 1 NC W4050 0 AGND C2308 AGND C2410 16V100 R2405 R2407 R2406 5.6K 1.8K R2307 5.6K ASP_CK SW+5V ASP_DA R2411 0 68 IC7100 C1BB00001061 ECHO_MUTE ECHO_LV2 ECHO_LV1 SW+5V R7110 1.5K B D 14 D7100 B0BC5R000009 A 2 W7000 0 SRW7001 0 SL- JK5000 1 SW+_OUT 2 3 C+_OUT FR+_OUT 4 FL+_OUT 5 SR+_OUT 6 SL+_OUT 7 SW-_OUT C-_OUT 8 9 FR-_OUT 10 FL-_OUT 11 SR-_OUT SL-_OUT 12 TO SPEAKERS AGND -7V TO MAIN SECTION (3/4) C5 H 77 1/4 2/4 3/4 4/4 SA-PT150GC/GCP/GCS/GCT/GS MAIN CIRCUIT SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 15 16 17 18 19 20 21 22 23 24 25 26 27 28 SCHEMATIC DIAGRAM - 6 C MAIN CIRCUIT R2427 :MAIN SIGNAL LINE 0 R2096 W4090 0 AGND_D 0.018 VREF TU_SD 10K 10K R2930 10K 0 R2932 R2931 MIC_SW VCC_CTRL MUTE_C MUTE_SURR C2007 0.1 220 TU_CLK R2161 47K ECHO_LVL1 NC NC ECHO_LVL2 NC NC NC NC NC NC NC VSS VCC DVD_CMD DVD_STAT DVD_CLK NC NC ECS ECK EDA NC MIC_EN NC SYNC RMT R2998 22K 78 DGND 2 STBLED 1 VREF 1 JOG_A 220 R2030 NC 7 GND 6 DO 5 DI NC 1 VCC 2 C W4067 0 KEY2 2 JOG_B 3 KEY2 4 DGND ASP_MICIN_1 -7V MIC_SW E TO VOLUME CIRCUIT (H6004) IN SCHEMATIC DIAGRAM - 9 CN2006 2 ASP_MICIN +7V 3 MIC_AGND 4 NC 5 6 -7V NC 7 MIC_SW 1 +7V MIC_AGND CN2005 D F TO MIC CIRCUIT (H6903) IN SCHEMATIC DIAGRAM - 10 R2032 47K R2017 27K R2019 27K E R2942 2.2K 220 R2029 10K 220 47K 10K R2024 R2043 Q2030 B1GBCFJJ0051 VREF CONTROL BRAKE_H 1 TRAY_OPEN 2 TRAY_CLOSE EEPROM (NOT SUPPLIED) W4063 LED DRIVE TRAY_CCW W4045 0 MGND Q2004 B1ADCE000012 D2929 B0ACCK000005 M+9V TRAY_CW STBLED F H2004 TRAY_OPEN 3 TRAY_CCW 4 VREF 5 GND (MGND) 6 C+7.5V D2935 D2936 TRAY_CW B0EAKM000117 B0EAKM000117 7 I TO TRAY LOADING CIRCUIT (CS901) IN SCHEMATIC DIAGRAM - 10 R2950 1K 0 R2944 CS 3 4.7K SYNC ECS G ECK SK 4 EDA W4066 0 W4069 0 MICROP-GND SYS6V C2162 680P R2261 47K R2999 22K R2928 220 220 R2927 R2929 10K O/P VCC CTRL MIC_SW MUTE_C_S TU_DI TUNER CLK 2 PORT_SEL 1 R2901 220 R2052 1K 1K 1K R5312 MUTE_F_SW MUTE_FRONT DC_DET1 NC STYB NC NC NC JOG_A JOG_B C2004 0.01 C2003 50V22 TO MAIN SECTION (4/4) TUN-LCH D2008 B0ACCK000005 RMT 3 31 C2013 0.022 C2161 TUN-RCH TU_ST R2160 56K KEY1 4 32 R2087 22K TUNER LCH 5 TUNER SD 4 TUNER DI 3 0.018 C2006 50V3.3 RESET 5 33 VREF 8 C4 TUNER DO/ST 6 TUN+9V C2261 TU_SD IC2004 C2262 680P TUNER RCH 7 16V100 R2260 56K TU_CLK X2001 H2B100500004 D2005 B0ACCK000005 Q2003 B1GBCFJJ0051 1 AGND C2169 0.01 B TO TUNER EXTENT CIRCUIT (CP2010) IN SCHEMATIC DIAGRAM - 9 TUNERGND 10 T+9V 9 NC 8 TU_ST 220 R2086 22K C2012 330P D2007 B0ACCK000005 CHASSIS C2022 220 R2040 DGND DGND R2428 0 C2026 220 R2042 D TO PANEL CIRCUIT (CN6001) IN SCHEMATIC DIAGRAM - 9 -VP (FL-) FL2 TRAY_CLOSE C2011 330P 0 R2044 DGND TU_DI 1 R2085 4.7K 0 10K C2010 330P R2430 PCONT C2009 0.1 R2429 220 R2041 W4057 0 W4100 0 VGND 50 R2047 3 2 6 FLD_CLK FLGND (FL+) FL1 MUTE_DVD R2031 RMT 220 100K W4053 0 VIDEO_MUTE 220 R2039 DVD_STA DVD_CMD R2001 0 JOG_B 220 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 DVD_CK 4.7K 7 ECS R2095 0 W4068 B R2943 2.7K TRAY_OPEN 7 JOG_A R2048 220 TRAY_CW 6 W4085 0 R2049 R2023 TRAY_CCW 5 PY PY/Y/G 49 CN2002 R5112 R5212 220 R2046 220 220 R2062 R2060 220 R2064 4 VGND VGND 48 C3 W4080 STYB JOG_B JOG_A 47K 47K 10K R2053 3 0.1 33K...GC/GS 22K...GCS/GST 120K...GCP CB CB/PB/B 47 C2001 2 8 NC 34 ECK VGND 46 0 0.1 1 W4071 0 220 C2000 CR CR/PR/R 45 99 100 TUN_CLK 36 10K R2022 R2089 TRAY_CLOSE Y Y 43 VGND 44 97 0 220 W4070 MIXL W4012 W4089 0 0 220 TUN_ST 37 R2045 W4086 0 TUN_SD 35 EDA MIXR C C2833 16V10 96 AVSS R2015 DVD-FL DVD_A+5V VGND 42 95 DES1 TUN_DI 38 [33]NC [32]NC [31]NC 220 1K 1 R2082 R2092 R2080 10K...GC/GS 3.3K...GCS/GST 22K...GCP [97]KEY1 [98]VREF [99]AVCC [100]BRAKE_H 93 DES3 94 DES2 10K R2090 BRAKE_H NC 39 R2098 220 C2111 10K NC 47 92 MD1 98 DVD-FR R2111 12K 10K R2081 R2088 NC 48 R2016 R2211 12K R2079 FLD_OUT (FL-) FL2 KEY1 W4059 JOG_A NC 49 PCONT 40 SYNC 1 4.7K 11 W4056 10 0 9 NC 50 EPM 41 SYSTEM CONTROL VCC NMI C2211 220 W4058 0 -VP JOG_B DVD_MUTE 42 IC2018 C2CBYY000438 90 MD2 91 KEY2 FLD_STB STBLED NC 43 89 MD3 SW+5V 12 VREF NC 44 XIN 1 88 DC_DET2 XOUT VSS C2101 R2101 12K 87 FLD_OUT 820 KEY1 DVD-SL R2201 12K 220 FLGND (FL+) FL1 RMT NC 45 NC RESET 1 ADAC5V 40 C 41 TO MAIN SECTION (1/4) ECHO_LV2 VMUTE 46 [81]RGB [82]YC_H [83]ASP_CLK [84]ASP_DAT 86 FLD_STB NC C2201 R2300 22K R2073 [51]ECHO_MUTE W4064 0 MIXL 39 ECHO_MUTE ECHO_LV1 85 FLD_CLK C2008 6.3V100 ADAC5V 38 10V1 DVD-SR 220 R2010 220 ADACGND 36 MIXR 37 C2300 DVD-CNT R2400 22K 10V1 R2078 220 0 R2072 84 CNVSS FR 33 ADACGND 34 FL 35 C2400 3.3K...GC/GS 4.7K...GCS/GST R2077 6.8K...GCP R2075 R2070 W4062 83 BYTE ADACGND 32 10V1 R2093 DVD-SUBW R2500 22K 220 82 R2084 47K SR 29 ADACGND 30 SL 31 C2500 R2071 FLD_OUT DC_DET2 81 NC ADACGND 26 CENTER 27 ADACGND 28 R2069 KEY2 R2600 1K 10V1 ASP_DA 220 220 W4065 0 SUBW 25 C2600 220 R2068 NC I/P VCC CTRL VREF 24 R2067 DGND D+5V 22 ZFLAG 23 A FLD_CLK 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 ASP_CK FLD_STB Q2006 B1GBCFJJ0051 INVERTER 10K 2.2K FLD_CLK MUTE_DVD D+5V 19 D+5V 20 AUDIODIGITAL 21 TO DVD MODULE CIRCUIT (FP8101) IN SCHEMATIC DIAGRAM - 2 FLD_OUT CN2007 13 FLD_STB W4060 0 R2006 1.8K R2002 TRAY_OPEN DVD_D+5V 10K R2097 470K D+5V 17 DGND 18 R2094 R2066 RGB DGND 16 10K NC L2009 G0C220JA0055 10K R2076 TRAY_CW A+5V 13 AGND 14 A+5V 15 R2012 WIDE1 AGND 12 DVD+2.7V AGND C2021 10V220 2.7V 11 10K SCART_MUTE DGND 10 R2091 TRAY_CCW AGND & DGND TRAY_CLOSE 9 W4055 0 SW+5V M+9V 220 2.7V 8 220 7 R2004 M+9V DGND R2003 6 220 5 MGND R2065 M+9V MGND DVD_CK R2000 220 4 R2063 3 MGND W4061 0 DSPCLK DVD_CMD 2 R2007 1 R2074 10K STATUS CMD DVD_STA R2061 10K E2901 DC_DET1 MUTE_FRONT_SW 1 VREF CN2001 :AUX / MIC SIGNAL LINE :DVD VIDEO SIGNAL LINE :FM SIGNAL LINE 220 2 :+B SIGNAL LINE R2005 CHASSIS 3 A :-B SIGNAL LINE 1/4 2/4 3/4 4/4 SA-PT150GC/GCP/GCS/GCT/GS MAIN CIRCUIT H SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS SCHEMATIC DIAGRAM - 7 :-B SIGNAL LINE C MAIN CIRCUIT :+B SIGNAL LINE :MAIN SIGNAL LINE :DVD VIDEO SIGNAL LINE :AUX / MIC SIGNAL LINE :FM SIGNAL LINE C Y C2810 0.01 C2812 0.1 W4018 0 4 SEL GND2 MUTE1 CIN S2 S1 VSAG VOUT SDCOUT COUT 20 5 CVIN YIN GND2 19 6 YOUT BIAS CYOUT 18 9 YSAG SEL CYSAG 17 10 8 7 21 22 23 24 25 26 DVD_A+5V C2807 0.01 3 2 1 27 28 29 30 31 32 VCC1 C2809 10V220 L2801 G0C220JA0055 W4016 0 GND GND2 MUTE2 CYIN 13 CRIN GND2 14 CROUT 11 CBOUT 15 CRSAG VCC2 12 CBIN 16 W4014 0 C2811 0.1 R2804 1K D2810 B0JCAE000001 W4006 W4013 W4011 0 0 0 C2817 1 C2818 1 Q2801 R2803 1K K TO MAIN SECTION (1/4) C2808 10V220 CBSAG J PY Q2801 B1GBCFJJ0051 MUTING CB CR VIDEO_MUTE RGB C5 I IC2801 C9ZB00000461 6 5 4 IN1 GND IN2 SW OUT VCC IC2802 C1AB00001731 L C2802 6.3V1000 C2800 1 C2806 6.3V330 C2805 6.3V330 C2804 1 VIDEO BUFFER VIDEO BUFFER 2 TO MAIN SECTION (4/4) 3 AUX 3 2 1 COMPONENT VIDEO OUT 2 3 INVERTER W4091 0 W4084 0 W4005 0 R5762 150K Q5746 B1GBCFJJ0051 C5791 16V100 0.1 C5799 C5798 50V100 R5758 3.3M R5755 10K C5796 50V2.2 R5759 100K 10K B0ACCK000005 +13V GND K4030...GC/GS 0 C1 K4031...GCS/GCT 0 K4032...GCP 0 VIDEO OUT C5795 0.1 Q5744 B1ABCF000176 R5763 2.7K R5764 3.9K B0ACCK000005 D5744 C5797 50V1 FLGND FAN MOTOR DRIVE +26V R5736 2.2K C5790 1000P Q5742 B1ABCF000176 D5743 FAN DC SUPPLY C2853 1/4 2/4 3/4 4/4 SA-PT150GC/GCP/GCS/GCT/GS MAIN CIRCUIT 100P SPEAKER CHASSIS GND 1 W4002 0 W4003 0 C5792 6.3V220 R5754 56K Q5745 B1ACKD000005 R5761 2.2M VIDEO GND JK2002 4 FAN MOTOR DRIVE FAN MOTOR DRIVE R5766 10K C2827 100P [Y] 5 [PR] 6 [PB] [R-CH] [L-CH] P 7 R5756 10K R5760 +26_VCC PCONT 8 C5794 16V33 W2201...GC/GS 0 O 9 D5700 B0ACCK000005 R5765 10K W4017 0 C2825 100P GND 2 R5757 10K DC_DET2 C2823 100P C2826 100P FANDCOUT(+) 1 FANLOCK 3 L2804 J0JBC0000015 C2164 220P TO FAN W4001 0 FAN LOCK DETECT CN5704 L2805 J0JBC0000015 L2803 J0JBC0000015 L2802 J0JBC0000015 C2264 220P R2816 75 R2813 75 R2812 75 R2809 75 DC_DET2 N Q5741 B1ABCF000176 W4004 0 C2 Q5740 B1BACG000023 D5745 B0BC013A0007 VOUT VOUT YOUT CBOUT CROUT YOUT CROUT CBOUT AGND AUX_RCH AUX_LCH M DGND VGND C2841 6.3V1000 1 4 5 6 7 HEATSINK GND 8 79 9 10 11 12 13 14 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS SCHEMATIC DIAGRAM - 8 I :-B SIGNAL LINE C MAIN CIRCUIT :+B SIGNAL LINE IN_R GND IN_L MUTE OUT-_L GND_L OUT+_L 5 6 7 8 9 10 11 12 C5124 0.1 FR_IN R5101 C5104 220P 12K H2002 +9.1V D2900 B0BC7R500001 R2900 SYS6V 1 PCONT 6 5 4 GND GND +9.1V 3 2 GND 1 GND 4 TO SMPS (CN2) TO SMPS (CN3) SYNC SYS6V W4023 0 R5108 27K R5104 27K IN_R GND IN_L MUTE OUT-_L GND_L OUT+_L R5205 C5202 22 0.1 STBY R5209 C5206 0.1 22 W4038 W4037 0 0 R5208 27K IN_L MUTE OUT-_L GND_L OUT+_L 7 8 9 10 11 12 SW+_OUT C5324 0.1 SW+ R5305 C5302 22 0.1 GND 6 SW-_OUT SW- C+_OUT C5305 470P C- O OUT_GND GND 3 MUTE_FRONT_SW +26V/18V(VCC) 2 +26V/18V(VCC) 1 D2000 B0JCPD000025 1/4 2/4 3/4 4/4 SA-PT150GC/GCP/GCS/GCT/GS MAIN CIRCUIT VCC C1 15 16 17 18 19 20 N C+ C-_OUT STBY C5308 16V22 7 5 IN_GND H2001 C5503 35V1000 PCONT 4 C5313 50V10 D5302 B0ACCK000005 10 VCC_CTRL 9 (FL-) FL2 8 (FL+) FL1 3 C5304 470P MICROP-GND SL- M 2 R5302 22K R5313 47K C5505 470P W4054 0 W4024 0 C_IN L SL+ R5309 C5306 22 0.1 -21V 11 -VP (-21V) L2800 (FL+) FL1 G0C220JA0055 OUT-_R R5204 27K R2911 47 SL-_OUT 1 R5301 33K SW_IN STYB -21V VCC_CTRL (FL-) FL2 22K IN_R POWER SR- SL+_OUT C5205 470P STBY IC5300 AN17831A SR+ R5308 27K R2974 4.7 22K OUT-_R MUTE_SURR SR+_OUT SR-_OUT R5304 5.6K DC DETECT C5224 0.1 R5202 FLGND D2905 B0BC7R500001 R2975 4.7K C2985 0.01 -VP REGULATOR D2974 MAZ82200ML C2986 50V100 Q2974 B1ACKD000005 -VP R2976 150 12 IN_GND FLGND Q2905 B1GBCFJJ0051 11 W4039 0 SL_IN C5301 50V10 VOUT 10 GND_R SS R2921 27K 9 R5211 10K VCC L2902 G0A101G00022 8 C5208 16V22 LX(OUT) R2925 1K 7 R5201 +9.1V GND 1 6 C5204 470P MGND CHASSIS_GND NC 2 C2952 0.1 AMPO 3 L2909 G0A200D00002 C2967 6.3V1000 DC_DET1 4 5 W4040 0 SR_IN C2901 16V470 DGND B0BC3R400001 D2944 C2925 6.3V220 22 5 C2969 0.1 R2973 220 R2972 6 D2904 C2921 B0JCPD000025 16V470 C2924 0.1 R2919 270K 7 C2970 0.1 DVD 2.7V REGULATOR C2919 10P R2971 R2926 1.5 1.5 R2920 4.7K DVD2.7V C2984 0.1 700mA C2983 16V100 DVD+2.7V Q2914 B1BACG000023 C2920 8200P AGND_D C2922 16V470 500mA AMPN DVD_D+5V DC-DC CONVERTER L2910 G0A220GA0026 4 OUT+_R E2900 IC2903 AN30071A-NM L2911 G0A200D00002 500mA 3 -21V 2.7K VGND DVD_A+5V 2 R5311 10K -7V REGULATOR K 1 C5201 50V10 R2914 FL- FL+_OUT VCC Q2906 B1BCCG000002 18K FL-_OUT GND_R POWER R2912 47 R5534 FL+ R5111 10K IC5200 AN17831A R2913 47 12K OUT+_R MUTE_FRONT_SW C5108 16V22 ASP_GND W4022 0 IN_GND R2977 0 1 2 3 C2964 1 C2914 10V33 -7V R2915 2.7K W4094 0 1 C2910 0.01 60mA C2961 1 W4093 0 W4095 0 -7V REGULATOR W4083 0 R2940 39K -7V Q2907 B1ADCF000001 0.01 DC DETECT C2913 16V100 Q2910 B1ABCF000176 C2903 W4081 0 TO MAIN SECTION (3/4) W4025 0 R2908 R2907 3.9K 220 R2924 68K W4082 0 +9.1V R5102 J FR+_OUT 22K VCC TUNER +9V 60mA R5533 W4021 0 FL_IN 2 FR- FL+_OUT 220P 3 +9.1V FR+_OUT FR-_OUT C5105 MGND FR+ R5105 C5102 0.1 22 STBY 4 1 DC_DET1 SYNC 3 R5109 C5106 0.1 22 D2918 B0ADCJ000020 2 W4020 0 15mA +9.1V 1 C5101 50V10 SW+5V ASP_GND 300mA C2975 16V100 M+9V OUT-_R POWER C2 GND_R IC5100 AN17831A OUT+_R TO MAIN SECTION (2/4) VCC C4 :MAIN SIGNAL LINE 21 22 80 23 24 25 26 27 28 P SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 19.3. Tuner Extent, Panel & Volume Circuit 1 3 5 6 7 8 9 10 11 12 13 14 SCHEMATIC DIAGRAM - 9 D PANEL CIRCUIT :FM SIGNAL LINE CP2010 FL6901 A2BD00000170 NX(G10) P2 P3 NX(G9) P4 P5 NX(G8) P6 P7 NX(G7) P8 P9 NX(G6) NX(G6) P10 P11 NX(G5) P12 NX(G4) P13 NX(G4) P14 G3 P15 P16 P17 G2 G10 NX(G1) G9 G8 NX(G1) G7 G6 G5 G1 G4 NP F2 F2 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 G4 G1 G5 G6 G7 G6 G8 G3 G2 G9 G10 G4 G5 G2 G6 P17 G7 G8 P16 G3 G4 G5 G6 G7 G8 G9 IC6901 C0HBB0000057 6 P11 P13 P12 P14 P8 24 P15 10 P16 P7 25 P17 9 STB P18 P6 26 P9 23 P6 D P7 P8 P9 P10 P11 P12 P13 P14 P16 P15 P17 C6909 0.01 C6910 6.3V100 C6911 0.01 C6913 50V3.3 P5 P5 27 12 13 14 15 16 17 18 19 20 21 22 SW+5V P4 P4 28 8 CLK 11 P3 P3 29 DISPLAY DRIVER 7 DIN 30 W6504 0 5 OSC 68 P2 P2 31 -VP W6502 0 P1 P1 32 3 68 G1 G1 33 2 R6914 82K C6916 100P SELECTOR G10 VCC GND 44 43 42 41 40 39 38 37 36 35 34 1 R6918 22K R6916 G9 P15 G10 G3 C C6906 100P R6919 C6917 100P R6805 2.2K PLAY S6805 STOP S6804 R6804 1.8K S6806 R6803 1.2K REVERSE S6803 FORWARD R6802 1K P14 P13 P12 P11 P10 P9 P8 P7 P6 P5 P4 P3 P1 F2 SW+5V 1 B F1 VCC 2 C6805 100P C6806 100P 10 4 FLD_CLK1 FLD_STB1 R6801 1K S6801 9 R6917 1K JOG_B 2 KEY2 3 DGND 4 8 GND 3 JOG_B S6802 JOG_A 1 7 FLGND FLD_OUT1 OPEN/CLOSE C TO MAIN CIRCUIT (CN2005) IN SCHEMATIC DIAGRAM - 6 H6004 6 R6936 10 L6903 J0JBC0000041 W6101...GC/GCS 0 JOG_A 5 D6910 B0BC3R400001 -VP VR6800 EVEKE2F2524M VOLUME JOG D 4 R6940 0 C6905 50V22 E VOLUME CIRCUIT DGND 3 FL2 W6545 0 PORT_SEL 1 2 R6939 0 FL1 2 TUNER CLK 1 PORT_SEL 1 P2 3 TUNER DI TUNER DI 3 P1 5 TUNER LCH 4 TUNER SD TUNER LCH 5 TUNER SD 4 NX(G10) 6 TUNER DO/ST TUNER DO/ST 6 FL DISPLAY NP C TO MAIN CIRCUIT (CN2002) IN SCHEMATIC DIAGRAM - 6 F1 7 TUNER RCH W6102...GC/GS 0 8 RDS DETECT TUNER RCH 7 C6903 50V22 RDS DETECT 8 TUNER CLK 2 C :-B SIGNAL LINE :+B SIGNAL LINE 10 TUNERGND 9 T+9V TUNERGND 10 T+9V 9 TO TUNER PACK (J3CBBB000001) A :+B SIGNAL LINE B TUNER EXTENT CIRCUIT CN2010 B 4 F1 A 2 -VP E E SW+5V 13 FLD_STB1 FLD_STB 12 FLD_OUT 11 F FLD_CLK1 W6509 0 Z6900 B3RAB0000025 FLGND REMOTE CONTROL SENSOR (FL+) FL1 8 -VP 7 (FL-) FL2 6 KEY1 5 RMT 4 DGND 3 STBLED 2 VREF 1 C6918 10V47 S6800 KEY1 RMT W6513 0 3 2 1 F POWER STBLED R6905 VREF 1.5K W6511 0 R6934 C6904 1000P C TO MAIN CIRCUIT (CN2007) IN SCHEMATIC DIAGRAM - 6 FLD_OUT1 FLD_CLK 10 FLGND 9 D6900 B3AAA0000803 W6512 0 CN6001 47 G G SA-PT150GC/GCP/GCS/GCT/GS TUNER EXTENT / PANEL / VOLUME CIRCUIT H 1 2 3 4 5 6 7 8 81 9 10 11 12 13 14 H SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 19.4. Mic, USB Relay, USB, Tray Loading & Optical Pickup Unit Circuit 1 3 4 5 6 7 8 9 10 11 12 13 14 SCHEMATIC DIAGRAM - 10 F MIC CIRCUIT 3 6 4 5 V- A W6514 0 C6706 0.1 C6701 R6701 1 0 VR6081 EVUE27FK3B53 MIC VOLUME 1 ASP_MICIN 2 3 +7V MIC_AGND 4 NC 5 -7V 6 NC 7 MIC_SW C TO MAIN CIRCUIT (CN2006) IN SCHEMATIC DIAGRAM - 6 CN8003 5 TO DVD MODULE CIRCUIT (FP9001) IN SCHEMATIC DIAGRAM - 1 H6903 0 1 K8005 J0JHC0000096 DGND 1 1 DGND DGND 2 2 DGND D+ 3 3 D+ D- 4 4 D- VBUS 5 5 VBUS CN8002 H TO USB CIRCUIT (CN8000) IN SCHEMATIC DIAGRAM - 10 K8004 J0JHC0000096 B JK6802 W6517 0 7 2 1 R6703 680 0.1 8 15K V+ R6706 R6705 1K C6707 47P W6516 0 C6709 C6711 R6710 10K MIC AMP 1 :USB SIGNAL LINE 0 IC2204 C0ABBB000230 W6550 0 10K R6707 C6708 R6708 47P 18K B G USB RELAY CIRCUIT :MIC SIGNAL LINE :+B SIGNAL LINE R6702 R6709 A :-B SIGNAL LINE C6703 C6702 47P 1000P A 2 5 3 2 4 1 C C 3 L6081 0 C6093 0.047 R6081 0 L6082 J0JBC0000030 MIC 2 1 L6083 J0JBC0000019 6 7 D D E E H USB CIRCUIT F CN8000 2 D3 D+ NC OUT2 VCC TRAY CW 1 VBUS GND CN8001 L8002 ERJ6GEY0R00V VS D+ 3 D- 4 VBUS 5 IC904 C0GAY0000013 OUT1 DGND 2 TRY OPEN DGND 1 TO USB RELAY CIRCUIT (CN8002) IN SCHEMATIC DIAGRAM - 10 VREF G I TRAY LOADING CIRCUIT :USB SIGNAL LINE 9 8 7 6 5 4 3 2 1 TRAY LOADING MOTOR DRIVE CS901 TO USB 4 DGND K8003 0 D+ S901 PLAY K8002 0 G L8003 ERJ6GEY0R00V VA8002 EZJZ1V171AA C984 25V10 VA8001 EZJZ1V171AA D- :+B SIGNAL LINE TRAY CW M+9V GND1 VREF+ TRAY CCW TRY CLOSE TRY OPEN 7 6 5 4 3 2 1 F C TO MAIN CIRCUIT (H2004) IN SCHEMATIC DIAGRAM - 6 S902 OPEN LOADING MOTOR (REF NO.316) G M SA-PT150GC/GCP/GCS/GCT/GS MIC / USB RELAY / USB / TRAY LOADING CIRCUIT H 1 2 3 4 5 6 7 8 82 9 10 11 12 13 14 H SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 1 A 2 3 4 5 6 7 8 9 10 11 12 13 14 SCHEMATIC DIAGRAM - 11 A OPTICAL PICKUP UNIT CIRCUIT (FOR REFERENCE ONLY) B TO HFM C TO LDU L4 GND VCC GND GND OUT GND GND TB TA TC TD FE1 FE2 1m RF GND VREF VCC SUB2 SUB1 SW LD(CD) LD(DVD) LDGND TO ACT L3 C8 R2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 R4 C2 C1 C3 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 T+ F+ FTHFM TA TB TD TC FE2 FE1 GND(Im) RF VREF2(RF-) PIN(DVD) LD(CD) LD GND LD(DVD) GND(OEIC) VREF1 VCC SUB2 SUB1 PIN(CD) SW GND(Im) B A TO DVD MODULE CIRCUIT (FP8531) IN SCHEMATIC DIAGRAM - 4 C R1 VR1 R3 D D R5 R6 R7 C5 VR2 C6 L2 C7 L1 C4 E E F F G G SA-PT150GC/GCP/GCS/GCT/GS OPTICAL PICKUP UNIT CIRCUIT H 1 2 3 4 5 6 7 8 83 9 10 11 12 13 14 H SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 84 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 20 Printed Circuit Board 20.1. DVD Module P.C.B. DVD MODULE P.C.B (REPX0562A...GC/GS/GCP) (REPX0562B...GCS/GCT) C8256 R8263 C8262 15 5 R8154 5 4 3 2 R9034 LB8001 45 50 C8691 5 60 LB9001 R9008 R9009 C9005 C9004 R8601 R8611 1 55 50 45 35 C8021 40 30 IC8001 25 20 144 15 10 5 5 3 6 C8022 65 4 C8007 70 2 IC9003 R9040 R9080 C8232 R8233 R8230 C8527 C8524 C8512 C8525 R8042 75 RX8691 3 4 C9007 C8606 K8001 C8532 R8532 LB8531 C8571 C8529 C8601 LB8561 LB8551 80 162 8 1 168 163 173 178 C8014 C8015 IC9005 LB8691 LB8693 4 RX8013 C9006 183 188 193 198 203 R8011 C8016 216 C8004 RX8017 RX8016 RX8018 RX8015 RX8014 RX8011 208 C8012 C8013 C8003 R9042 RX8012 RX8019 C8422 28 R8420 25 C8427 RX8032 15 20 C8428 B QR8420 85 X9004 C8020 C8006 R8341 C8541 C8304 C8429 LB8430 IC8695 1 C8421 E R8041 90 154 LB8692 C 95 RX8001 149 1 C8011 100 RX8402 54 54 C8057 C8526 R8561 R8551 D8211 Q8335 R8332 Q8341 4 C8502 C8002 FL8104 40 5 3 2 1 FL8101 5 C8423 35 C8056 28 LB8401 C8695 FL8102 105 C8602 RX8031 C8008 GCS/GCT 1 RX8611 139 RX8403 3 2 1 FL8103 10 LB8011 C IC8691 4 C8503 C8504 1 R9036 R9037 129 RX8401 15 LB8425 C8001 IC8151 C8521 124 C8401 3 5 R8232 119 R8325 20 C8231 R8231 E 134 30 LB8690 1 R9035 IC8051 LB8302 C8302 X8621 C8151 C8430 1 IC8606 C8018 10 4 C8005 15 R8326 25 1 3 109 R8401 20 C8055 27 C8052 C8051 C R8424 RX8111 LB8423 C8651 C8053 C8054 R8321 R8327 2 114 R8322 C8325 IC8601 2 108 R8221 Q8325 E 35 LB8427 RX8020 R8013 C8652 C8221 C LB8422 LB8491 C8026 48 E B 40 6 5 4 C8152 45 1 2 3 B C8321 B RX8533 4 QR8571 R8225 Q8321 C8222 45 QR8111 R8153 40 R9033 35 R9032 30 C8622 R8622 R8621 C8621 RX8531 R8531 C8211 C8225 R8342 R8324 LB8301 R8323 R8328 LB8421 C8306 25 K8421 C8111 C8311 D 8 RX8532 C R8552 C9018 5 C8226 C E FP8101 50 L8302 E B R8541 C8320 IC8111 R8312 C8303 B C8312 R8311 C8203 C8202 IC8651 C8112 1 C E R8331 R8336 R8333 4 C8301 C E R8314 L8201 C8513 C R8211 C8341 C8340 B B R8335 L8301 C8514 Q8331 C8113 LB8303 C8515 B R8337 C8335 R8343 LB8305 C8330 C8516 E LB8571 K8251 C8563 C8562 C8201 LB8428 1 5 LB8426 10 R8334 C8331 LB8431 15 Q8551 R8533 C8531 C8522 C8501 LB8429 20 L8330 LB8424 24 L8550 L8501 5 R8562 Q8561 LB8304 R8002 4 C9008 14 LB8257 E C R9043 IC8611 (NOT SUPPLIED) C8553 C8552 C8611 8 C8561 C8550 C8551 1 8 C8313 C8564 R8564 R8565 29 C8261 R8262 R8264 R8567 R8566 R8563 7 R8313 R8559 B R8568 GCS/GCT E C R8557 R8265 K8006 R8553 1 Q8562 E B R8558 R8556 F R8555 C8554 C C8572 RX8534 C8252 R8554 C8251 C8533 IC8251 C8523 C8257 21 C8505 30 C8253 22 C8254 Q8552 LB8530 C8530 28 R8261 LB8259 26 C8511 20 LB8260 15 R8012 C8258 10 LB8258 5 C8255 1 D8571 FP8531 (TO OPTICAL PICKUP UNIT) C8528 G C8305 A R8251 H B R9044 IC8421 C8424 1 5 10 R9045 FP9001 C8426 1 2 3 4 (TO SPINDLE / TRAVERSE MOTOR) 6 5 5 4 3 2 1 C8402 R8421 C8263 FP8251 14 PbF 0518A PbF 0518A A (SIDE A) 1 SA-PT150GC/GS/GCS/GCT/GCP DVD MODULE P.C.B. (SIDE B) 2 3 4 5 6 7 85 8 9 10 11 12 13 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 20.2. Main P.C.B. MAIN P.C.B. (REPX0581D...GCS/GCT, REPX0581E...GC/GS, REPX0581F...GCP) 1 F W4016 C2812 C2161 C2026 W2081 W2082 W2040 C2022 C2808 W2039 W4100 3 R2160 R2161 W2041 L2803 5 W2038 C2823 C2825 W2037 L2805 R2809 R2816 6 W2281 4 32 C2802 C2800 C2169 C2162 W2267 17 R2812 C2804 C2806 L2802 7 6 5 4 3 2 1 IC2801 4 6 W2033 C2805 2 1 W2268 8 C2262 R2261 R2260 C2261 R2803 16 CN2002 10 9 C2810 C2807 W2032 W2035 1 IC2802 C2827 COMPONENT VIDEO OUT 3 L2801 W2036 VIDEO OUT C2841 3 C2826 L2804 R2813 JK2002 1 R2804 C2818 W4017 W4018 D2810 G C2817 C2811 C B E W2258 C2809 W2282 Q2801 W2043 C W2042 H C2264 AUX C2164 2 W2283 W2017 W2019 W4012 W4011 W4013 W2018 W2020 W4090 W4089 W2021 W4085 W4084 W2022 W2023 W4086 W2024 W2025 W2026 W4099 E W4004 2 3 H2001 (TO SMPS CN2) W7011 R2975 B C2008 W4055 W4056 C2000 W4060 R2012 R2089 R2094 W7014 W2277 R2072 R2075 R2077 R2093 R2074 W2177 R2069 R2073 CN2006 6 5 4 3 W2170 C2901 R2002 R2071 L2800 7 R2974 C R2076 W4061 R2091 R2088 R2097 R2081 R2080 D2008 W2186 C2985 W2184 W2181 R2066 W2182 W4062 R2068 R2070 W2179 R2090 W2176 R2079 C2004 C2007 C2003 D2007 W2194 C2013 W2192 D2005 R2052 R2053 W2187 R2063 R2999 W2149 4 R2067 Q2974 W2171 2 1 R2911 H2002 (TO SMPS CN3) 1 2 3 4 5 6 7 8 9 10 11 W4054 R2900 D2900 W7016 85 81 R2998 W2185 W2172 C5505 1 W4066 R2042 W4069 R2901 R2930 R2927 R2061 W2180 R5212 E W2130 C5503 90 75 R2976 W2286 W4058 R2096 R2004 R2082 CN2007 W2183 W2279 W2167 K2901 K2913 C2919 R2919 6 W4059 R2003 R2001 D2974 W7017 IC2903 R2925 R2921 R5112 7 W4068 1 2 3 4 5 6 7 8 9 10 11 12 13 100 R2078 R2000 R2092 C2986 W7012 W2284 R2065 W2175 X2001 W4057 R2005 5 95 R2064 L2902 1 W4067 W2197 1 70 R2060 80 R2062 D2904 W2136 W2133 W2091 K2903 C2922 D2000 W2134 C2021 C7105 C7106 C2970 C7118 R2912 W4080 W2276 R2046 W2152 R2913 W2092 K2902 L2911 D7100 C7112 Q7102 10 IC2018 Q2004 R2944 W2129 W2195 R2024 15 C B E R2950 R2029 64 R5312 W2150 W2189 W2191 55 R2929 W7013 D2929 W4064 W4065 R2010 51 R2931 K2910 C2006 C R2095 W2193 R2022 45 R2928 W2148 C7104 R7102 K2912 50 R2932 E B R2031 W2196 W2143 W2162 L2909 W4038 W4071 R2048 R2049 K2915 W2147 C2009 R2023 R2017 R2007 W2131 W4070 W2198 R2032 R2030 W2138 R2019 C2001 30 31 R2016 W2173 35 25 R2015 R2098 40 20 W2174 3 2 1 R2047 W7010 Q2003 R2084 R2039 R2041 W2140 HEATSINK 8 R2040 R2043 R2045 R2044 W2144 2 C2921 5 W7015 L2009 W4098 K2905 W2166 W4053 L2910 W4082 D2905 R2926 C2969 R2914 R2087 C2920 C2910 C C2952 W7002 W2285 E R7103 R7105 R7116 C7114 W2161 1 W2278 R2920 R7112 C7115 4 C2012 W2146 W7000 W2128 1 W2160 R2006 C7108 C7107 R7107 E B B E R7110 Q7101 5 B E C7113 C R2086 W2178 W2164 W2163 R2971 D2944 C2925 K2918 W2300 R2924 R2907 C7111 C7110 R7101 R7120 C7120 C7103 R7114 Q7100 C7102 C7119 C Q2006 C2983 R7109 W2159 C2010 W2153 W2302 W2301 W2145 K2914 W2168 W2108 W2169 W2127 W2120 W2110 W4048 W4095 W4081 C W4037 W4040 W2093 W2054 W2056 E B 8 8 W4039 R5202 R5211 12 IC7100 1 IC7101 C7116 W2086 IC5200 R5204 R7100 B 9 4 C2011 W2190 R2085 C2984 C7109 W2202 R7104 16 C7101 Q2906 W2046 C5224 (GC/GS) R7106 W2099 C2903 R2972 (NOT SUPPLIED) W4063 R2427 W2158 C C2967 E B C Q2905 R2940 W2083 1 W2104 W2118 W2124 W2123 W2125 W7018 W2112 C2309 C2601 R2601 W2113 C2410 D2001 R2606 W2096 C2961 R2915 W4094 W4093 C5205 C5204 R5208 R2952 C2913 R7113 W7001 R3014 R2973 D2918 A Q2907 C2964 R3003 D2002 C2914 C2617 C R3006 C3007 R3005 K2907 E C2924 R2908 Q2910 E B W2098 Q3003 R2617 R3007 R3015 C3006 R3009 D3001 B E Q3009 C3009 R3008 W2100 Q3008 W2097 C W2084 R5201 R5534 W2051 C C B E C5208 W4022 W4021 C E B C B R2960 R2411 R2612 C2605 R2301 C2401 R2402 C2402 C2403 R2403 C2619 C2303 C2611 W4042 Q2914 C2975 IC2004 1 W2154 C R2608 R2609 R2611 R2627 R2610 C2302 R2302 E B W4047 C2406 R2307 W4050 C2308 C2608 R2401 C2612 W4025 W4023 R5111 R5102 W2122 W2116 W2121 W4083 W2126 W2115 W2106 R2407 W2280 R2339 R2439 W2060 L5204 C2503 R2502 R2503 C2502 W2061 R2412 C2412 W2059 W4043 R2512 31 35 R2977 R2607 C2607 C2610 C2609 40 C5201 W2048 C5108 R5101 W4045 W2079 R2111 W2074 C2172 C2272 C2165 C2115 W2057 C2119 R2215 C2221 C2220 C2219 C2501 C2283 R2501 C2183 L5201 C5308 C5313 C5101 W2053 R5760 R5533 R2620 2 W2157 CN2001 CA E2901 3 C2833 47 43 39 35 31 27 23 19 15 11 7 3 49 45 41 37 33 29 25 21 17 13 9 5 1 R2406 W4049 R2621 45 W2058 C2405 C2305 R2430 R2428 48 44 40 36 32 28 24 20 16 12 8 4 50 46 42 38 34 30 26 22 18 14 10 6 2 W2094 D5743 B E Q5744 R5311 W2052 C C5104 C5105 W4020 W2004 D5744 R5759 Q5742 51 W2044 IC5100 R5104 R5108 R5313 C C2606 50 C2506 C2624 12 C5124 D5302 C5795 W4003 R5764 R5758 R5762 C5304 R5304 E B R5308 C5305 W2111 C2312 C3005 C2301 R2510 R2312 R2626 C2524 C2724 L5301 C5301 C5324 1 C2023 C2201 R2429 W2105 C2300 C2400 R2303 W2047 12 R2201 W2107 W2109 R2185 W2045 IC5300 7 C2211 R2101 C2101 IC2102 L5202 W2002 5 6 55 W2000 W2001 W2005 CW4002 Q5741 2 E R5761 1 B E A C Q5745 3 4 60 R2194 R2294 R5302 C2853 R5755 B R5301 C5792 1 E W4001 C5790 W2006 3 C R5766 W2003 2 (GC/GS) R5754 B R5765 Q5740 1 R5763 D5745 R5736 C5791 B C C5799 (TO FAN) 2 C5797 Q5746 E CN5704 8 1 2 65 W4026 C5798 W2072 H2004 R2619 C2615 C2423 C6921 W4034 95 C2295 C2195 100 R2113 C2117 C2118 1 C2116 5 C2324 C2424 R2285 L5302 W2007 C2017 R6921 R5305 3 7 1 L5104 L5303 C R2405 C2323 R2436 R2300 R2500 C2500 R2600 C2600 R2400 C2507 R2511 R2336 R2404 C2304 C2404 R2165 R2304 80 C2265 81 C2408 C2407 85 75 C2306 R2265 90 70 C2024 C2307 W4024 9 L5203 C5106 L5304 C5306 4 SUBWOOFER B C5202 C5102 R5309 W2076 E B R2943 R2942 10 C2114 C2216 R2114 R2218 15 C2214 R2214 C2120 20 C2215 C2121 25 C2217 R2115 C2218 30 L5102 10 D5700 CENTER SPEAKER L5103 L5101 C5796 FRONT SPEAKER R 5 C5302 FRONT SPEAKER L R5109 R5105 11 W2201 C 6 Q2030 W2064 W4028 C2019 W2049 C5206 SURROUND SPEAKER R JK5000 R5757 R5756 C5794 SURROUND SPEAKER L R5205 W2275 W4096 R2264 C2212 R2212 R2112 C2112 K4032 (GCP) W4007 R2211 C2020 R2164 R5209 12 C2018 K4030 (GC/GS) C6920 R6920 W2077 D W4091 W2015 W4006 W2010 W4005 W2075 W2200 C2111 W2014 K4031 (GCS/GCT) D2935 D2936 R2191 R2291 W2063 W2080 W2062 W2073 W2070 W2065 W2071 W2069 W2067 W2068 W2066 W2009 W2029 W2013 W2012 W2030 W2008 W2027 W2011 W2028 W2117 W2078 W4014 W2137 W2139 W2135 E2900 3 CN2005 4 3 2 1 2 1 PbF 0534A 3 4 5 6 7 86 8 SA-PT150GC/GS/GCS/GCT/GCP MAIN P.C.B. 9 10 11 12 13 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 20.3. Panel, Volume & Tuner Extent P.C.B. PANEL P.C.B. (REPX0581D...GCS/GCT) (REPX0581E...GC/GS) (REPX0581F...GCP) 1 2 5 7 8 10 11 13 14 16 20 17 W6509 W6504 W6101 Z6900 W6008 R6905 W6511 W6103 W6512 C6904 R6934 R6939 L6903 28 29 30 31 C6917 R6916 R6919 C6916 11 12 C6918 W6104 32 R6914 C6906 22 1 33 35 36 38 39 40 41 42 44 45 FL6901 W6002 W6001 W6004 W6003 W6006 IC6901 23 C6909 44 W6102 W6005 R6940 D6910 (GC/GS) W6100 F 3 C6913 C6903 D6900 C6905 C6911 W6010 R6918 S6800 (POWER) 2 27 25 23 W6012 W6011 1 21 W6502 W6513 R6917 C6910 G R6936 D W6545 H 34 33 PbF 0534A CN6001 2 4 6 5 3 1 12 10 8 7 9 13 11 SENSOR E E D B VOLUME P.C.B. (REPX0581D...GCS/GCT) (REPX0581E...GC/GS) (REPX0581F...GCP) TUNER EXTENT P.C.B. (REPX0581D...GCS/GCT) (REPX0581E...GC/GS) (REPX0581F...GCP) H6004 S6802 C (FORWARD) S6803 1 S6801 (REVERSE) 2 3 10 9 7 6 5 4 3 2 1 3 2 1 (OPEN/CLOSE) C6805 VR6800 C6806 CN2010 R6802 R6801 8 CP2010 4 (TO TUNER PACK) R6803 R6804 3 2 S6806 1 S6805 (PLAY) (SELECTOR) R6805 10 9 PbF 0534A S6804 8 7 6 5 4 (STOP) B PbF 0534A VOLUME A SA-PT150GC/GS/GCS/GCT/GCP PANEL/VOLUME/TUNER EXTENT P.C.B. 1 2 3 4 5 6 7 87 8 9 10 11 12 13 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 20.4. Mic, USB, USB Relay & Tray Loading P.C.B. H G USB P.C.B. (REPX0581D...GCS/GCT) (REPX0581E...GC/GS) (REPX0581F...GCP) 1 2 L6082 W6516 W6550 7 6 3 VA8001 4 R6701 R6708 C6701 R6707 C6707 C6711 IC2204 C6703 R6705 1 4 4 5 3 CN8001 (TO USB) 2 1 5 MIC L6081 4 1 7 6 H6903 PbF 0534A 3 L6083 8 W6514 3 C6706 5 CN8000 VA8002 R6081 R6706 R6702 C6702 F 2 C6708 C6709 R6703 1 JK6802 W6517 VR6081 L8003 MIC VOLUME L8002 MIC P.C.B. (REPX0581D...GCS/GCT) (REPX0581E...GC/GS) (REPX0581F...GCP) K8002 F K8003 H 2 C6093 5 4 3 2 1 R6709 R6710 PbF 0534A E G CN8002 K8004 C I USB RELAY P.C.B. (REPX0581D...GCS/GCT) (REPX0581E...GC/GS) (REPX0581F...GCP) TRAY LOADING P.C.B. (REP4238A) REF NO.316 S902 PbF 0534A + (OPEN SW) 5 4 M IC904 - 1 2 3 4 S901 3 (PLAY SW) 2 C984 D K8005 1 4 5 K8001 7 5 6 6 5 7 8 9 4 3 2 1 PbF 2462A-1 2 3 CS901 1 CN8003 B A SA-PT150GC/GS/GCS/GCT/GCP MIC/USB RELAY/USB/TRAY LOADING P.C.B. 1 2 3 4 5 6 7 88 8 9 10 11 12 13 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 21 Basic Troubleshooting Guide 21.1. Basic Troubleshooting Guide for Traverse Unit (DVD Module P.C.B) Problems 1) Distorted picture or abnormal sound is head during the initialization 2) No TOC / Long TOC 3) Disc not spinning 4) Traverse not moving 5) Traverse and spindle abnormal movement 6) Cannot read the disc but spindle motor is spinning - Cannot read CD/DVD 7) Block Noise during play 8) Jitter out of specification 9) Cannot read data from USB Checking Points a) Check SDRAM address, data bus, CLK and other control signals waveform b) Check video signals Checking Components IC8051 c) Check audio DAC circuitry LB8301, R8321, R8322, LB8302, R8325, R8326 IC8421 * Compare the above with OK condition DVD module P.C.B. *Check for solder short and/or component missing/damaged a) Check motor driver circuitry (+5V) b) Check laser drive circuitry (Voltages & current) c) Check LSI IC connection to motor drive circuitry *Compare the above with OK condition DVD Module P.C.B. IC8251 Pin 8, 21 a) Check connection from DVD Module to Traverse unit b) Check motor driver circuitry on the voltages and control signals *Compare the above with OK condition DVD Module P.C.B a) Check laser drive circuitry (voltages and current) - Check CD Laser Drive - Check DVD Laser Drive * Check voltages and LD current and compare with OK condition DVD Module P.C.B. FP8251 a) Check SDRAM address and data bus signal a) Check LD current b) Check OPU (Change to other unit and confirmed operating condition) IC8051 Q8551, Q8552, Q8561, Q8562 IC8001 Pin 66, 67 * Check for solder short and/or component missing/damaged IC8251 *Check for solder short and/or component damaged Q8551, Q8552, LB8531 (For DVD Laser Drive current) Q8561, Q8562, LB8561 (For CD Laser Drive current) OPU Unit (Traverse unit), FPC connection a) Check USB connector & FFC FP9001 b) Check LSI O/P IC8001 Pin 144, 146 c) Check IC supply (+5V) IC9005 Pin 2, 3 89 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 21.2. Basic Troubleshooting Guide for SMPS/MAIN/PANEL Problems 1) No power supply to unit Checking Points a) Check AC cord connection (open/short) Checking Components b) Check fuse F1 on SMPS Module P.C.B. F1 c) Check supply voltage to Main P.C.B. from SMPS Module P.C.B. (+5V/+7V/2.7V) H2002 Pin 1, 4, 8, 9, 11 d) Check cable connection between SMPS Module & Main P.C.B. e) Check DC voltage (+9.1V) 2) No FL Display 3) No audio output IC2903, L2909 Pin 2, 3 a) Check supply voltage (Refer to Item 1) checking points b) Check SYS6V to IC2018 IC2018 Pin 16 c) Check oscillator circuit X2001, IC2018 Pin13, 16 d) Check soldering condition IC2018, IC6901, FL6901 a) Check speaker connection * Solderability condition JK5000 b) Check amplifier IC circuit (audio output) IC5100, IC5200, IC5300 Pin 4, 10 b) Check supply to amplifier IC IC5100, IC5200, IC5300 Pin 1 90 { { { TO PANEL BLOCK TO TUNER TO FAN TO ASP TO DV5 L +26V FL1/FL2 +9.1V -VP -7V SW+5V +7V DCDET1 Regulator Regulator + - DCDET1 IC2903 DC-DC CONVERTER POWER SUPPLY BLOCK DVD 2.7V Regulator D+5 A+5 AUX (DVD_MUTE/ DVD_STA/ DVD_CMD/ DVD_CK) (TU_DI/TU_ST/TU_CLK/TU_SD) TUNER DV5 DL2SU LOADING (TRAY_OPEN/ TRAY_CLOSE/ TRAY_CCW/ TRAY_CW) C - + SMPS BLOCK IC2102 ASP IC SW+5V 2 {A RGB {B WIDE ASP_MICIN ASP_DA/ASP_CLK IC2018 MICRO-P IC IC2004 EEPROM C SYS6V PCONT DCDET1 VCC_CTRL 1 FLD_STB1 (PY/Y) IC2801 VIDEO IC B -VP A Muting IC1102 Switch DCDET1 ECHO_LV2 PCONT ECHO_LV1 ECHO_MUTE IC1101 SCART IC +26V +26V IC7100 ECHO IC FAN CIRCUIT BLOCK +7V +7V/-7V (VOUT /R_OUT /G_OUT /B_OUT) IC7100 FL1/FL2 (SCART TERMINAL) JK1001 (AUX/CB /CR/Y /COMPOSITE) JK2001 D I S P L A Y FL6901 F L JK6802 MIC To Speaker Units JK5000 AUDIO L/R IC2204 MIC AMP IC5300 (C+/C- & SW+/SW-) IC5200 (SL+/LSR+/R-) AMP Section IC5100 (FL+/FR+/-) IC (C/Y/CR/CB/PY) MUTE_FR_SW MUTE_SURR STYB (SCART_MUTE) (VIDEO_MUTE) (WIDE_OUT) IC2802 IC Switch } IC6901 FL Driver IC PANEL BLOCK FLD_OUT1 { (C/Y/CR/CB/PY) } 91 FLD_CLK1 A+5V } SC-PT150 SIMPLIFIED BLOCK SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 22 Overall Block Diagram for PT150 22.1. SC-PT150 Simplified Block SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 23 Terminal Function of ICs 23.1. IC2018 (C2CBYY000438): System Control IC Pin Terminal Name No. 1 TRAY_CLOSE 2 TRAY_CCW 3 TRAY_CW 4 TRAY_OPEN 5 NC 6 I/P VCC_CTRL 7 NC 8 BYTE 9 CNVSS 10 NC 11 NC 12 RESET 13 XOUT 14 VSS 15 XIN 16 VCC 17 NMI 18 19 20 21 RMT SYNC NC MIC_EN 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 NC EDA ECK ECS NC NC DVD_CLK DVD_STAT DVD_CMD NC NC NC NC TUN_SD TUN_CLK TUN_DO TUN_DI NC PCONT EPM I/O Function I LOADING MECHA CLOSE SW (L: SW ON) O Terminal for tray control 1 O Terminal for tray control 2 I LOADING MECHA OPEN SW (L: SW ON) - MIC Insertion Detect (if MIC_EN = 1) I Input Power Supply Control I I I I I I/O O O I I O I 0 I O O I 42 DVD_MUTE I 43 44 45 46 47 48 49 50 51 52 53 54 O O O O - NC NC NC VMUTE NC NC NC NC ECHO_MUTE ECHO_LVL1 ECHO_LVL2 NC Pin No. 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 No Connection VSS (GND) VSS (GND) No Connection RDS Enable (H = Enable, L = Disable) SYSTEM RESET INPUT MAIN CLOCK OUTPUT (10.0MHZ) GND (0V) MAIN CLOCK INPUT (10 MHZ) POWER SUPPLY (5V) CONNECT TO VCC EXTERNAL INTERRUPT I/P REMOCON INPUT AC FAILURE DETECT INPUT No Connection Microphone Enable (L=Disable, H=Enable) No Connection DATA signal for the EEPROM CLOCK signal for the EEPROM LAT signal for the EEPROM No Connection No Connection CLK signal for the DVD Module STATUS signal from the DVD Module CMD signal for the DVD Module No Connection No Connection No Connection No Connection Tuner Station Detect I2C Clock for Tuner Stereo Detect I2C Data for Tuner No Connection Control Signal for Power Relay CONNECTED TO GROUND VIA RESISTOR Signal from DVD module control mute circuit No Connection No Connection No Connection Video Mute Control No Connection No Connection No Connection No Connection ECHO MUTING CONTROL ECHO LEVEL CONTROL 1 ECHO LEVEL CONTROL 2 No Connection 92 Terminal Name NC NC NC NC NC NC NC VCC NC VSS O/P VCC_ CTRL MIC_SW MUTE_C_S MUTE_F_SW MUTE_FRONT DC_DET1 STYB NC NC NC NC JOG_A JOG_B NC SCART_MUTE WIDE1 RGB YC_H ASP_CLK ASP_DAT FLD_CLK FLD_STB FLD_OUT DC_DET2 MD3 MD2 KEY 2 MD1 DES3 DES2 DES1 AVSS KEY1 VREF AVCC BRAKE_H I/O Function O No Connection No Connection No Connection No Connection No Connection No Connection No Connection POWER SUPPLY 5.0V No Connection GND (0V) Ouput VCC Supply Control O O O O I O I I O O I O O O O O O I I I I I I I I I O PULL UP RESISTOR TO SUPPLY Center and Surround L & R Mute Front L & R Mute and SubWoofer Mute Front Mute DC Detection circuit 1 Standby Mode No Connection No Connection No Connection No Connection Signal A from Volume JOG Signal B from Volume JOG No Connection Line out for SCART terminal Control Signal for the WIDE function Mute signal 1 for Video output Control signal for the video signal Mix Clock Signal for 6 Channel ASP IC Data Signal for ASPC IC Clock Signal for the FL Driver FL Strobe FL Data Out DC Detection circuit 2 Model Code 3 Model Code 2 Key 2 line input Model Code 1 DVD Region Setting Model Selector REGION Setting for Tuner Analog Power Supply Input Key 1 Line input Reference Voltage Input Analog Power Supply Input Terminal for tray control 3 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 24 Exploded Views 93 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 94 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 24.1. Cabinet Parts Location 95 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 96 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 24.2. Packaging 97 SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 25 Replacement Parts List Notes: · Important safety notice: Components identified by mark have special characteristics important for safety purpose. Furthermore, special parts which have purposes of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc. are used. When replacing any of components, be sure to use only manufacture’s specified parts shown in the parts list. · Warning: This product uses a laser diode. Refer to caution statements. · Capacity values are in microfarads (µF) unless specified otherwise, P=Pico-farads (pF), F=Farads (F). · Resistance values are in ohms, unless specified otherwise, 1K=1,000 (OHM), 1M=1,000K (OHM). · The parenthesized indications in the Remarks columns specify the model names and areas. (Refer to the cover page) · The marking (RTL) indicates the retention time is limited for this item. After the discontinuation of this assembly in production, it will no longer be available. · Parts mentioned [M] are supplied from PAVCSG. · Parts mentioned [SPG] are supplied from PAVC. · Reference for O/I book languages are as follows: Ar: Cf: Cz: Da: Pe: Arablic Canadian French Czech Danish Persian Du: En: Fr: Ge: Ur: Dutch English French German Ukrainian It: Ko: Po: Ru: Pr: · 98 Italian Korean Polish Russian Portuguese Sp: Sw: Co: Cn Spanish Swedish Traditional Chinese Simplified Chinese SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS 25.1. Component Parts List Ref. No. Part No. Part Name & Description Ref. No. 330 331 332 333 340 341 342 343 Remarks CABINET AND CHASSIS 1 2 3 4 5 7 J3CBBB000001 L6FAJCCH0007 REEX0613 REEX0679 REEX0736 REXX0384-J TUNER PACK SMALL DC FAN MOTOR 50P FFC (MECHA) 5P FFC (MECHA) 13P FFC WIRE (FL) 7P FLAT WIRE (DVD) 8 9 10 12 13 14 15 REXX0519 REXX0520 REXX0521 REXX0589 RGKX0325A-S1 RGLX0128-Q RFKGAPT150EE 4P FLAT WIRE(VOLUME) 11P FLAT WIRE (MAIN) 4P FLAT WIRE (MAIN) 5P USB WIRE DVD LID LIGHTING CHIP FRONT PANEL ASS’Y 15 16 16 RFKGAPT150GP RGRX0058F-J RGRX0058F-K FRONT PANEL ASS’Y REAR PANEL REAR PANEL 16 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 39 40 41 42 RGRX0058F-M RGRX0058F-N RGUX0665-S RGUX0666-S RGUX0676-S RGWX0076-S RHD26046 RHD30007-1SJ RHD30092-1 RHD30111-3 RHD30119-S RHDV30006 RKA0059-K RKMX0107-1S3 RMAX0086-2 RMAX0101 RMAX0108-1 RMKX0117-4 RMNX0109 RMNX0149 RMYX0191A RMZX0029 RXXX0090 XTB3+8JFJ N0AZ6GE00006 RGWX0352A-K REXX0531 REAR PANEL REAR PANEL POWER BUTTON FUNCTION BUTTON OPEN CLOSE BUTTON VOLUME KNOB SCREW SCREW SCREW SCREW SCREW SCREW LEG RUBBER TOP CABINET PANEL ANGLE BRACKET MECHA HOLDER BOTTOM CHASSIS PCB SPACER FL HOLDER HEATSINK EXTRUSION MAIN PCB INSOLATOR HEATSINK UNIT SCREW SMPS MODULE MIC KNOB 7P FLAT WIRE (MIC) [M] [M] [M] [M] [M] [M]GC/G CS/GS [M] [M] [M] [M] [M] [M] [M]GC/G CS/GCT/ GS [M]GCP [M]GCS [M]GC/G S [M]GCT [M]GCP [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] RMK0591A RHM0003-J RDG0547 RDG0548-1 RDG0549 RDV0070 REM0133 RGQ0395-K1 RME0350 RME0351A RME0353 RML0627-2 RML0628 RML0629 RML0631 RMM0247-3 RMM0248 RMR1446-X RMR1447-X RMR1468-K MECHA CHASSIS MAGNET PULLEY GEAR RELAY GEAR DRIVE GEAR BELT MOTOR UNIT TRAY CHANGE LEVER SPRING LOCK LEVER SPRING TRAY SLIDER SPRING DRIVE ARM CHANGE LEVER LOCK LEVER TRAY SLIDER DRIVE RACK SUB RACK CLAMPER MAGNET HOLDER CLAMP PLATE XTN26+6GFJ XTV2+6GFJ XWG6FFJ RMC0387 RAE2023Z-S RMG0598A-K RMR1596-X2 RMS0789 Part Name & Description SCREW PCB SCREW WASHER SUPPORT SPRING TRAVERSE UNIT FLOATING RUBBER MIDDLE CHASSIS FIXED PIN Remarks [M] [M] [M] [M] [M] [M] [M] [M] PRINTED CIRCUIT BOARDS REPX0562A REPX0562B REPX0581D REPX0581E REPX0581F REP4238A DVD MODULE P.C.B. [M] (RTL)GC /GCP/GS DVD MODULE P.C.B. [M] (RTL)GC S/GCT MAIN/TUNER [M] EXTENT/PANEL/VOLUME/MIC/USB/U (RTL)GC SB RELAY P.C.B. S/GCT MAIN/TUNER [M] EXTENT/PANEL/VOLUME/MIC/USB/U (RTL)GC SB RELAY P.C.B. /GS MAIN/TUNER [M] EXTENT/PANEL/VOLUME/MIC/USB/U (RTL)GC SB RELAY P.C.B. P TRAY LOADING P.C.B. [M] (RTL) INTEGRATED CIRCUITS TRAVERSE DECK 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 Part No. [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] IC904 IC2018 IC2102 IC2204 IC2801 IC2802 IC2903 IC5100 IC5200 IC5300 IC6901 IC7100 C0GAY0000013 C2CBYY000438 C1AB00002463 C0ABBB000230 C9ZB00000461 C1AB00001731 AN30071A-NM AN17831A AN17831A AN17831A C0HBB0000057 C1BB00001061 IC7101 IC8001 IC8051 IC8111 IC8151 IC8251 IC8421 IC8601 IC8606 IC8651 C0ABBB000230 MN2DS0018MP C3ABPG000145 C0CBCBD00018 C0DBEHG00006 C0GBG0000048 C0FBBK000050 C0EBA0000029 C0EBE0000456 RFKWMHC0B320 IC TRAY LOADING MOTOR DRIVE IC SYSTEM CONTROL IC AUDIO SIGNAL PROCESSOR IC MIC AMP IC VIDEO BUFFER IC VIDEO BUFFER IC DC-DC CONVERTER IC POWER IC POWER IC POWER IC DISPLAY DRIVER IC DIGITAL DELAY WITH ECHO VOLUME IC MIC AMP IC DV5.0 LSI IC 64M SDRAM IC +3.3V DC-DC CONVERTER IC +1.2V REGULATOR IC MOTOR DRIVE IC AUDIO DAC IC RESET IC RESET IC 32M FLASH MEMORY IC8651 RFKWMHC0D320 IC 32M FLASH MEMORY IC8691 IC8695 IC9003 IC9005 C0JBAA000502 C0JBAA000502 C0JBAB000908 C0DBZYE00002 IC IC IC IC AND GATE AND GATE INVERTER GATE REGULATOR [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [SPG]GC /GCP/GS [SPG]GC S/GCT [M] [M] [M] [M] TRANSISTORS Q2003 Q2004 Q2006 Q2030 Q2801 Q2905 Q2906 Q2907 Q2910 Q2914 Q2974 Q3003 99 B1GBCFJJ0051 B1ADCE000012 B1GBCFJJ0051 B1GBCFJJ0051 B1GBCFJJ0051 B1GBCFJJ0051 B1BCCG000002 B1ADCF000001 B1ABCF000176 B1BACG000023 B1ACKD000005 B1GDCFJJ0047 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS Ref. No. Q3008 Q3009 Q5740 Q5741 Q5742 Q5744 Q5745 Q5746 Q7100 Q7101 Q7102 Q8321 Q8325 Q8331 Q8335 Q8341 Q8551 Q8552 Q8561 Q8562 Part No. Part Name & Description Remarks B1ABGC000005 B1ABCF000176 B1BACG000023 B1ABCF000176 B1ABCF000176 B1ABCF000176 B1ACKD000005 B1GBCFJJ0051 B1GBCFJJ0051 B1GBCFJJ0051 B1GBCFJJ0051 2SB1218ARL 2SB1218ARL 2SB1218ARL 2SB1218ARL 2SB1218ARL 2SD1819A0L B1ADGB000008 2SD1819A0L B1ADGB000008 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] QR8111 QR8420 QR8571 XP0621400L UNR521100L UNR511V00L CHIP TRANSISTOR CHIP TRANSISTOR CHIP TRANSISTOR [M] [M] [M] Ref. No. S6806 Part No. EVQ21405R Part Name & Description SW SELECTOR Remarks [M] CONNECTORS CN2001 CN2002 CN2005 CN2006 CN2007 CN2010 CN5704 CN6001 CN8000 CN8001 CN8002 CN8003 K1MY50AA0029 K1KA10AA0031 K1KA04AA0193 K1KA07AA0193 K1MN13AA0003 K1KA10AA0031 K1KA03AA0301 K1MN13BA0004 K1KA05BA0061 K1FY104B0011 K1KA05BA0061 K1MY05BA0130 50P CONNECTOR 10P CONNECTOR 4P CONNECTOR 7P CONNECTOR 13P CONNECTOR 10P CONNECTOR 3P CONNECTOR 13P CONNECTOR 5P CONNECTOR 4P CONNECTOR 5P CONNECTOR 5P CONNECTOR [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] CP2010 K1KB10B00042 10P CONNECTOR [M] CS901 K1KA07BA0061 7P CONNECTOR [M] FP8101 FP8251 FP8531 FP9001 K1MN50BA0173 K1MN06BA0148 K1MY26BA0025 K1MN05BA0148 50P CONNECTOR 6P CONNECTOR 26P CONNECTOR 5P CONNECTOR [M] [M] [M] [M] DIODES COILS & TRANSFORMERS D2000 D2001 D2002 D2005 D2007 D2008 D2810 D2900 D2904 D2905 D2918 D2929 D2935 D2936 D2944 D2974 D3001 D5302 D5700 D5743 D5744 D5745 D6900 D6910 D7100 D8211 D8571 B0JCPD000025 B0EAKM000117 B0EAKM000117 B0ACCK000005 B0ACCK000005 B0ACCK000005 B0JCAE000001 B0BC7R500001 B0JCPD000025 B0BC7R500001 B0ADCJ000020 B0ACCK000005 B0EAKM000117 B0EAKM000117 B0BC3R400001 MAZ82200ML B0ACCK000005 B0ACCK000005 B0ACCK000005 B0ACCK000005 B0ACCK000005 B0BC013A0007 B3AAA0000803 B0BC3R400001 B0BC5R000009 MA2J11100L MA2J72800L DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] L2009 L2800 L2801 L2802 L2803 L2804 L2805 L2902 L2909 L2910 L2911 L6081 L6082 L6083 L6903 L8002 L8003 L8201 L8301 L8302 L8330 L8501 L8550 EVUE27FK3B53 EVEKE2F2524M VR MIC LEVEL VR VOLUME JOG [M] [M] VA8001 VA8002 EZJZ1V171AA EZJZ1V171AA CHIP VARISTOR CHIP VARISTOR [M] [M] LB8001 LB8011 LB8257 LB8258 LB8259 LB8260 LB8301 LB8302 LB8303 LB8304 LB8305 LB8401 LB8421 LB8422 LB8423 LB8424 LB8425 LB8426 LB8427 SWITCHES S901 S902 S6800 S6801 S6802 S6803 S6804 S6805 RSH1A044-1A RSH1A044-1A EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R EVQ21405R SW SW SW SW SW SW SW SW PLAY OPEN POWER OPEN/CLOSE FORWARD REVERSE STOP PLAY COIL COIL COIL CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR COIL COIL INDUCTOR COIL CHIP JUMPER CHIP BEEZ CHIP INDUCTOR CHIP INDUCTOR CHIP RESISTOR CHIP RESISTOR CHIP COIL CHIP COIL CHIP COIL CHIP COIL CHIP COIL CHIP INDUCTOR [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] CHIP INDUCTORS VARIABLE RESISTORS VR6081 VR6800 G0C220JA0055 G0C220JA0055 G0C220JA0055 J0JBC0000015 J0JBC0000015 J0JBC0000015 J0JBC0000015 G0A101G00022 G0A200D00002 G0A220GA0026 G0A200D00002 ERJ3GEY0R00V J0JBC0000030 J0JBC0000019 J0JBC0000041 ERJ6GEY0R00V ERJ6GEY0R00V G1C100K00019 G1C100K00019 G1C100K00019 G1C100K00019 G1C100K00019 G1C100KA0055 [M] [M] [M] [M] [M] [M] [M] [M] 100 J0JHC0000045 J0JHC0000045 ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V J0JBC0000042 J0JBC0000042 J0JBC0000042 J0JBC0000042 J0JBC0000042 J0JBC0000042 ERJ2GE0R00X ERJ2GE0R00X ERJ2GE0R00X ERJ2GE0R00X ERJ2GE0R00X ERJ2GE0R00X ERJ2GE0R00X CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP INDUCTOR INDUCTOR RESISTOR RESISTOR RESISTOR RESISTOR BEAD BEAD BEAD BEAD BEAD BEAD RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS Ref. No. LB8428 LB8429 LB8430 LB8431 LB8491 LB8530 LB8531 LB8551 LB8561 LB8571 LB8690 LB8691 LB8692 LB8693 LB9001 Part No. ERJ2GE0R00X ERJ2GE0R00X J0JHC0000045 ERJ2GE0R00X ERJ2GE0R00X J0JHC0000045 ERJ2GE0R00X J0JBC0000042 J0JBC0000042 J0JBC0000042 J0JBC0000044 ERJ2GEJ101X ERJ2GEJ101X ERJ2GEJ101X J0JCC0000119 Part Name & Description CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP HIGH CHIP CHIP CHIP CHIP RESISTOR RESISTOR INDUCTOR RESISTOR RESISTOR INDUCTOR RESISTOR BEAD BEAD BEAD LOSS INDUCTOR RESISTOR RESISTOR RESISTOR INDUCTOR Remarks [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] COMPONENT COMBINATION Z6900 B3RAB0000025 REMOTE SENSOR Ref. No. A2 Part No. K2CQ2CA00002 AC CORD A2 K2CQ2CA00007 AC CORD A2 K2CT3CA00004 AC CORD A3 RQTX0028-2B O/I BOOK (EN) A3 RQTX0031-G OI BOOK (AR/PE) A3 RQTX0032-K OI BOOK (CN) A3 A4 A5 A6 A7 RQTX0033-M RSA0007-M K2KA2BA00001 K2DA42E00001 RQCA0968 O/I BOOK (SP) ANTENNA WIRE VIDEO CABLE AC PLUG ADAPTOR SPEAKER LABEL [M] H2B100500004 H0J270500085 H1A4805B0027 CERAMIC RESONATOR CRYSTAL OSCILLATOR CRYSTAL OSCILLATOR R2000 R2001 R2002 R2003 R2004 R2005 R2006 R2007 R2010 R2012 R2015 R2016 R2017 R2019 R2022 R2023 R2024 R2029 R2030 R2031 R2032 R2039 R2040 R2041 R2042 R2043 R2044 R2045 R2046 R2047 R2048 R2049 R2052 R2053 R2060 R2061 R2062 R2063 R2064 R2065 R2066 R2067 R2068 R2069 R2070 R2071 R2072 R2073 R2074 R2075 R2076 R2077 [M] [M] [M] DISPLAY TUBE FL6901 FL8101 FL8102 FL8103 FL8104 A2BD00000170 F1H0J1050018 F1H0J1050018 F1H0J1050018 F1J1E1040022 FL DISPLAY INDUCTOR INDUCTOR INDUCTOR INDUCTOR [M] [M] [M] [M] [M] FUSE F1 K5D502BNA005 FUSE [M] HOLDERS H2001 H2002 H2004 H6004 H6903 K1YF04000001 K1YZ11000002 K1YZ07000001 K1YZ04000002 K1YZ07000001 4P CABLE HOLDER 11P CABLE HOLDER 7P WIRE HOLDER 4P CABLE HOLDER 7P WIRE HOLDER [M] [M] [M] [M] [M] JACKS JK2002 JK5000 JK6802 K2HA306B0070 K4AC12B00003 K2HB102J0038 JACK COMPONENT VIDEO OUT JK SPEAKER JACK MIC [M] [M] [M] EARTH TERMINALS E2900 E2901 K4CZ01000027 K4CZ01000027 TERMINAL TERMINAL [M] [M] PACKING MATERIALS P1 P1 P1 P1 P1 P2 P3 P4 RPGX1727 RPGX1728 RPGX1729 RPGX1730 RPGX1731 RPNX0369-1 RPFX0058-1J RPNX0446 PACKING CASE PACKING CASE PACKING CASE PACKING CASE PACKING CASE POLYFOAM MIRAMAT POLYFOAM [M]GC [M]GS [M]GCS [M]GCT [M]GCP [M] [M] [M]GC/G CS/GS ACCESSORIES A1 A1-1 N2QAYB000092 RKK-HTR0051K REMOTE CONTROL R/C BATTERY COVER Remarks [M] GCT [M] GC/GCS/ GCP [M] GS [M]GC/G CS/GCT/ GS [M]GC/G S [M]GCS/ GCT [M]GCP [M] [M] [M]GCP [M]GCP/ GCT RESISTORS OSCILLATORS X2001 X8621 X9004 Part Name & Description [M] [M] 101 ERJ3GEYJ221V ERJ3GEYJ104V ERJ3GEYJ103V ERJ3GEYJ221V ERJ3GEYJ221V ERJ3GEYJ221V ERJ3GEYJ182V ERJ3GEYJ103V ERJ3GEYJ221V ERJ3GEYJ103V ERJ3GEYJ102V ERJ3GEYJ221V ERJ3GEYJ273V ERJ3GEYJ273V ERJ3GEYJ221V ERJ3GEYJ221V ERJ3GEYJ221V ERJ3GEYJ221V ERJ3GEYJ221V ERJ3GEYJ221V ERJ3GEYJ473V ERJ3GEYJ103V ERJ3GEYJ221V ERJ3GEYJ103V ERJ3GEYJ221V ERJ3GEYJ473V ERJ3GEYJ221V ERJ3GEYJ103V ERJ3GEYJ221V ERJ3GEYJ221V ERJ3GEYJ221V ERJ3GEYJ221V ERJ3GEYJ221V ERJ3GEYJ103V ERJ3GEYJ221V ERJ3GEYJ473V ERJ3GEYJ221V ERJ3GEYJ473V ERJ3GEYJ221V ERJ3GEYJ221V ERJ3GEYJ222V ERJ3GEYJ221V ERJ3GEYJ221V ERJ3GEYJ221V ERJ3GEYJ221V ERJ3GEYJ221V ERJ3GEYJ221V ERJ3GEYJ221V ERJ3GEYJ103V ERJ3GEYJ221V ERJ3GEYJ103V ERJ3GEYJ821V 220 1/16W 100K 1/16W 10K 1/16W 220 1/16W 220 1/16W 220 1/16W 1.8K 1/16W 10K 1/16W 220 1/16W 10K 1/16W 1K 1/16W 220 1/16W 27K 1/16W 27K 1/16W 220 1/16W 220 1/16W 220 1/16W 220 1/16W 220 1/16W 220 1/16W 47K 1/16W 10K 1/16W 220 1/16W 10K 1/16W 220 1/16W 47K 1/16W 220 1/16W 10K 1/16W 220 1/16W 220 1/16W 220 1/16W 220 1/16W 220 1/16W 10K 1/16W 220 1/16W 47K 1/16W 220 1/16W 47K 1/16W 220 1/16W 220 1/16W 2.2K 1/16W 220 1/16W 220 1/16W 220 1/16W 220 1/16W 220 1/16W 220 1/16W 220 1/16W 10K 1/16W 220 1/16W 10K 1/16W 820 1/16W [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS Ref. No. R2078 R2079 R2080 Part No. Part Name & Description ERJ3GEYJ472V ERJ3GEYJ103V ERJ3GEYJ103V 4.7K 1/16W 10K 1/16W 10K 1/16W R2080 ERJ3GEYJ332V 3.3K 1/16W R2080 R2081 R2082 R2084 R2085 R2086 R2087 R2088 R2089 ERJ3GEYJ223V ERJ3GEYJ103V ERJ3GEY0R00V ERJ3GEYJ473V ERJ3GEYJ472V ERJ3GEYJ223V ERJ3GEYJ223V ERJ3GEYJ103V ERJ3GEYJ223V 22K 1/16W 10K 1/16W 0 1/16W 47K 1/16W 4.7K 1/16W 22K 1/16W 22K 1/16W 10K 1/16W 22K 1/16W R2089 ERJ3GEYJ333V 33K 1/16W R2089 R2090 R2091 R2092 R2093 ERJ3GEYJ124V ERJ3GEYJ221V ERJ3GEYJ103V ERJ3GEYJ221V ERJ3GEYJ332V 120K 1/16W 220 1/16W 10K 1/16W 220 1/16W 3.3K 1/16W R2093 ERJ3GEYJ472V 4.7K 1/16W R2093 R2094 R2095 R2096 R2097 R2098 R2101 R2111 R2112 R2113 R2114 R2115 R2160 R2161 R2164 R2165 R2185 R2191 R2194 R2201 R2211 R2212 R2214 R2215 R2218 R2260 R2261 R2264 R2265 R2285 R2291 R2294 R2300 R2301 R2302 R2303 R2304 R2307 R2312 R2336 R2339 R2400 R2401 R2402 R2403 R2404 R2405 R2406 ERJ3GEYJ682V ERJ3GEYJ103V ERJ3GEYJ472V ERJ3GEYJ103V ERJ3GEYJ474V ERJ3GEYJ221V ERJ3GEYJ123V ERJ3GEYJ123V ERJ3GEYJ123V ERJ3GEYJ472V ERJ3GEYJ472V ERJ3GEYJ103V ERJ3GEYJ563V ERJ3GEYJ473V ERJ3GEYJ103V ERJ3GEYJ332V ERJ3GEYJ103V ERJ3GEYJ682V ERJ3GEYJ273V ERJ3GEYJ123V ERJ3GEYJ123V ERJ3GEYJ123V ERJ3GEYJ472V ERJ3GEYJ103V ERJ3GEYJ472V ERJ3GEYJ563V ERJ3GEYJ473V ERJ3GEYJ103V ERJ3GEYJ332V ERJ3GEYJ103V ERJ3GEYJ682V ERJ3GEYJ273V ERJ3GEYJ223V ERJ3GEYJ182V ERJ3GEYJ103V ERJ3GEYJ103V ERJ3GEYJ123V ERJ3GEYJ182V ERJ3GEYJ103V ERJ3GEYJ123V ERJ3GEYJ563V ERJ3GEYJ223V ERJ3GEYJ182V ERJ3GEYJ103V ERJ3GEYJ103V ERJ3GEYJ123V ERJ3GEYJ562V ERJ3GEYJ562V 6.8K 1/16W 10K 1/16W 4.7K 1/16W 10K 1/16W 470K 1/16W 220 1/16W 12K 1/16W 12K 1/16W 12K 1/16W 4.7K 1/16W 4.7K 1/16W 10K 1/16W 56K 1/16W 47K 1/16W 10K 1/16W 3.3K 1/16W 10K 1/16W 6.8K 1/16W 27K 1/16W 12K 1/16W 12K 1/16W 12K 1/16W 4.7K 1/16W 10K 1/16W 4.7K 1/16W 56K 1/16W 47K 1/16W 10K 1/16W 3.3K 1/16W 10K 1/16W 6.8K 1/16W 27K 1/16W 22K 1/16W 1.8K 1/16W 10K 1/16W 10K 1/16W 12K 1/16W 1.8K 1/16W 10K 1/16W 12K 1/16W 56K 1/16W 22K 1/16W 1.8K 1/16W 10K 1/16W 10K 1/16W 12K 1/16W 5.6K 1/16W 5.6K 1/16W Remarks Ref. No. R2407 R2411 R2412 R2427 R2428 R2429 R2430 R2436 R2439 R2500 R2501 R2502 R2503 R2510 R2511 R2512 R2600 R2601 R2606 R2607 R2608 R2609 R2610 R2611 R2612 R2617 R2619 R2620 R2621 R2626 R2627 R2803 R2804 R2809 R2812 R2813 R2816 R2900 R2901 R2907 R2908 R2911 R2912 R2913 R2914 R2915 R2919 R2920 R2921 R2924 R2925 R2926 R2927 R2928 R2929 R2930 R2931 R2932 R2940 R2942 R2943 R2944 R2950 R2952 R2960 R2971 R2972 R2973 R2974 R2975 R2976 R2977 R2998 [M] [M] [M]GC/G S [M]GCS/ GCT [M]GCP [M] [M] [M] [M] [M] [M] [M] [M]GCS/ GCT [M]GC/G S [M]GCP [M] [M] [M] [M]GC/G S [M]GCS/ GCT [M]GCP [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] 102 Part No. ERJ3GEYJ182V ERJ3GEY0R00V ERJ3GEYJ103V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEYJ123V ERJ3GEYJ563V ERJ3GEYJ223V ERJ3GEYJ682V ERJ3GEYJ103V ERJ3GEYJ682V ERJ3GEYJ153V ERJ3GEYJ123V ERJ3GEYJ563V ERJ3GEYJ102V ERJ3GEYJ473V ERJ3GEYJ103V ERJ3GEYJ103V ERJ3GEYJ563V ERJ3GEYJ152V ERJ3GEYJ563V ERJ3GEYJ122V ERJ3GEYJ563V ERJ3GEYJ223V ERJ3GEYJ203V ERJ3GEYJ123V ERJ3GEYJ393V ERJ3GEYJ104V ERJ3GEYJ683V ERJ3GEYJ102V ERJ3GEYJ102V ERJ3GEYF750V ERJ3GEYF750V ERJ3GEYF750V ERJ3GEYF750V ERJ3GEYJ1R0V ERJ3GEYJ103V ERJ3GEYJ392V ERJ3GEYJ221V ERG2SJ470E ERG2SJ470E ERG2SJ470E ERJ3GEYJ272V ERJ3GEYJ272V ERJ3GEYJ274V ERJ3GEYF472V ERJ3GEYF273V ERJ3GEYJ683V ERJ3GEYF102V ERX2SJ1R5E ERJ3GEYJ221V ERJ3GEYJ221V ERJ3GEYJ221V ERJ3GEYJ103V ERJ3GEYJ103V ERJ3GEYJ103V ERJ3GEYJ393V ERJ3GEYJ222V ERJ3GEYJ272V ERJ3GEYJ472V ERJ3GEYJ102V ERJ3GEYJ8R2V ERJ6GEYJ6R8V ERX2SJ1R5E ERJ3GEYJ220V ERJ3GEYJ221V ERD2FCVJ4R7T ERJ3GEYJ472V ERJ3GEYJ151V ERJ3GEY0R00V ERJ3GEYJ223V Part Name & Description 1.8K 1/16W 0 1/16W 10K 1/16W 0 1/16W 0 1/16W 0 1/16W 0 1/16W 12K 1/16W 56K 1/16W 22K 1/16W 6.8K 1/16W 10K 1/16W 6.8K 1/16W 15K 1/16W 12K 1/16W 56K 1/16W 1K 1/16W 47K 1/16W 10K 1/16W 10K 1/16W 56K 1/16W 1.5K 1/16W 56K 1/16W 1.2K 1/16W 56K 1/16W 22K 1/16W 20K 1/16W 12K 1/16W 39K 1/16W 100K 1/16W 68K 1/16W 1K 1/16W 1K 1/16W 75 1/16W 75 1/16W 75 1/16W 75 1/16W 1 1/16W 10K 1/16W 3.9K 1/16W 220 1/16W 47 1/32W 47 1/32W 47 1/32W 2.7K 1/16W 2.7K 1/16W 270K 1/16W 4.7K 1/16W 27K 1/16W 68K 1/16W 1K 1/16W 1.5 1/32W 220 1/16W 220 1/16W 220 1/16W 10K 1/16W 10K 1/16W 10K 1/16W 39K 1/16W 2.2K 1/16W 2.7K 1/16W 4.7K 1/16W 1K 1/16W 8.2 1/16W 6.8 1/10W 1.5 1/32W 22 1/16W 220 1/16W 4.7 1/4W 4.7K 1/16W 150 1/16W 0 1/16W 22K 1/16W Remarks [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS Ref. No. R2999 R3003 R3005 R3006 R3007 R3008 R3009 R3014 R3015 R5101 R5102 R5104 R5105 R5108 R5109 R5111 R5112 R5201 R5202 R5204 R5205 R5208 R5209 R5211 R5212 R5301 R5302 R5304 R5305 R5308 R5309 R5311 R5312 R5313 R5533 R5534 R5736 R5754 R5755 R5756 R5757 R5758 R5759 R5760 R5761 R5762 R5763 R5764 R5765 R5766 R6081 R6701 R6702 R6703 R6705 R6706 R6707 R6708 R6709 R6710 R6801 R6802 R6803 R6804 R6805 R6905 R6914 R6916 R6917 R6918 R6919 R6920 R6921 Part No. ERJ3GEYJ223V ERJ3GEYJ822V ERJ3GEYJ223V ERJ3GEYJ102V ERJ3GEYJ273V ERJ3GEYJ103V ERJ3GEYJ102V ERJ3GEYJ563V ERJ3GEYJ563V ERJ3GEYJ123V ERJ3GEYJ123V ERJ3GEYJ273V ERG2SJ220E ERJ3GEYJ273V ERG2SJ220E ERJ3GEYJ103V ERJ3GEYJ102V ERJ3GEYJ223V ERJ3GEYJ223V ERJ3GEYJ273V ERG2SJ220E ERJ3GEYJ273V ERG2SJ220E ERJ3GEYJ103V ERJ3GEYJ102V ERJ3GEYJ333V ERJ3GEYJ223V ERJ3GEYJ562V ERG2SJ220E ERJ3GEYJ273V ERG2SJ220E ERJ3GEYJ103V ERJ3GEYJ102V ERJ3GEYJ473V ERJ3GEYJ223V ERJ3GEYJ183V ERJ3GEYJ222V ERJ3GEYJ563V ERJ3GEYJ103V ERJ3GEYJ103V ERJ3GEYJ103V ERJ3GEYJ335V ERJ3GEYJ104V ERJ3GEYJ103V ERJ3GEYJ225V ERJ3GEYJ154V ERJ3GEYJ272V ERJ3GEYJ392V ERJ3GEYJ103V ERJ3GEYJ103V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEYJ153V ERJ3GEYJ681V ERJ3GEYJ102V ERJ3GEY0R00V ERJ3GEYJ103V ERJ3GEYJ183V ERJ3GEY0R00V ERJ3GEYJ103V ERJ3GEYJ102V ERJ3GEYJ102V ERJ3GEYJ122V ERJ3GEYJ182V ERJ3GEYJ222V ERJ3GEYJ152V ERJ3GEYJ823V ERJ3GEYJ680V ERJ3GEYJ102V ERJ3GEYJ223V ERJ3GEYJ680V ERJ3GEYJ101V ERJ3GEYJ222V Part Name & Description 22K 1/16W 8.2K 1/16W 22K 1/16W 1K 1/16W 27K 1/16W 10K 1/16W 1K 1/16W 56K 1/16W 56K 1/16W 12K 1/16W 12K 1/16W 27K 1/16W 22 1/32W 27K 1/16W 22 1/32W 10K 1/16W 1K 1/16W 22K 1/16W 22K 1/16W 27K 1/16W 22 1/32W 27K 1/16W 22 1/32W 10K 1/16W 1K 1/16W 33K 1/16W 22K 1/16W 5.6K 1/16W 22 1/32W 27K 1/16W 22 1/32W 10K 1/16W 1K 1/16W 47K 1/16W 22K 1/16W 18K 1/16W 2.2K 1/16W 56K 1/16W 10K 1/16W 10K 1/16W 10K 1/16W 3.3M 1/16W 100K 1/16W 10K 1/16W 2.2M 1/16W 150K 1/16W 2.7K 1/16W 3.9K 1/16W 10K 1/16W 10K 1/16W 0 1/16W 0 1/16W 15K 1/16W 680 1/16W 1K 1/16W 0 1/16W 10K 1/16W 18K 1/16W 0 1/16W 10K 1/16W 1K 1/16W 1K 1/16W 1.2K 1/16W 1.8K 1/16W 2.2K 1/16W 1.5K 1/16W 82K 1/16W 68 1/16W 1K 1/16W 22K 1/16W 68 1/16W 100 1/16W 2.2K 1/16W Remarks Ref. No. R6934 R6936 R6939 R6940 R7100 R7101 R7102 R7103 R7104 R7105 R7106 R7107 R7109 R7110 R7112 R7113 R7114 R7116 R7120 R8002 R8011 R8012 R8013 R8041 R8042 R8153 R8154 R8211 R8221 R8225 R8230 R8231 R8232 R8233 R8251 R8261 R8262 R8263 R8264 R8265 R8311 R8312 R8313 R8314 R8321 R8322 R8323 R8324 R8325 R8326 R8327 R8328 R8331 R8332 R8333 R8334 R8335 R8336 R8337 R8341 R8342 R8343 R8401 R8420 R8421 R8424 R8531 R8532 R8533 R8541 R8551 R8552 R8553 [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] 103 Part No. ERJ3GEYJ470V ERJ3GEYJ100V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEYJ153V ERJ3GEYJ153V ERJ3GEYJ153V ERJ3GEYJ153V ERJ3GEYJ153V ERJ3GEYJ153V ERJ3GEYJ124V ERJ3GEYJ680V ERJ3GEYJ472V ERJ3GEYJ152V ERJ3GEYJ272V ERJ3GEYJ103V ERJ3GEYJ562V ERJ3GEYJ393V ERJ3GEYJ153V ERJ2GEJ103X ERJ2GEJ220X ERJ2GEJ220X ERJ2GEJ220X ERJ2GEJ330X ERJ2GEJ103X ERJ2RHD621X ERJ2RHD102X ERJ2GEJ103X ERJ2GEJ822X ERJ2GEJ822X ERJ2GEJ222X ERJ2GEJ223X ERJ2GEJ752X ERJ2GEJ222X ERJ6GEYJ6R8V ERJ2GEJ823X ERJ2GEJ153X ERJ2GEJ823X ERJ2GEJ153X ERJ2GE0R00X ERJ2RHD242X ERJ2RHD102X ERJ2RHD153X ERJ2RHD153X ERJ3RBD201V ERJ3GEY0R00V ERJ2GEJ330X ERJ2RHD102X ERJ3RBD201V ERJ3GEY0R00V ERJ2GEJ330X ERJ2RHD102X ERJ3RBD201V ERJ3GEY0R00V ERJ2GEJ330X ERJ2RHD102X ERJ3RBD201V ERJ2GEJ330X ERJ2RHD102X ERJ3RBD201V ERJ2GEJ330X ERJ2RHD102X ERJ2GEJ101X ERJ2GEJ222X ERJ2GE0R00X ERJ2GE0R00X ERJ2GEJ152X ERJ2GEJ222X ERJ2GE0R00X ERJ2GEJ153X ERJ2GE0R00X ERJ2GEJ102X ERJ2GEJ102X Part Name & Description 47 1/16W 10 1/16W 0 1/16W 0 1/16W 15K 1/16W 15K 1/16W 15K 1/16W 15K 1/16W 15K 1/16W 15K 1/16W 120K 1/16W 68 1/16W 4.7K 1/16W 1.5K 1/16W 2.7K 1/16W 10K 1/16W 5.6K 1/16W 39K 1/16W 15K 1/16W 10K 1/32W 22 1/32W 22 1/32W 22 1/32W 33 1/32W 10K 1/32W 620 1/32W 1K 1/32W 10K 1/32W 8.2K 1/32W 8.2K 1/32W 2.2K 1/32W 22K 1/32W 7.5K 1/32W 2.2K 1/32W 6.8 1/10W 82K 1/32W 15K 1/32W 82K 1/32W 15K 1/32W 0 1/32W 2.4K 1/32W 1K 1/32W 15K 1/32W 15K 1/32W 200 1/16W 0 1/16W 33 1/32W 1K 1/32W 200 1/16W 0 1/16W 33 1/32W 1K 1/32W 200 1/16W 0 1/16W 33 1/32W 1K 1/32W 200 1/16W 33 1/32W 1K 1/32W 200 1/16W 33 1/32W 1K 1/32W 100 1/32W 2.2K 1/32W 0 1/32W 0 1/32W 1.5K 1/32W 2.2K 1/32W 0 1/32W 15K 1/32W 0 1/32W 1K 1/32W 1K 1/32W Remarks [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS Ref. No. R8554 R8555 R8556 R8557 R8558 R8559 R8561 R8562 R8563 R8564 R8565 R8566 R8567 R8568 R8601 R8611 R8621 R8622 R9008 R9009 R9032 R9033 R9034 R9035 R9036 R9037 R9040 R9042 R9043 R9044 R9045 R9080 Part No. Part Name & Description ERJ2GEJ680X ERJ2GEJ2R2X ERJ3GEYJ560V ERJ3GEYJ510V ERJ2GEJ473X ERJ2GEJ153X ERJ2GE0R00X ERJ2GEJ102X ERJ2GEJ102X ERJ2GEJ220X ERJ2GEJ2R2X ERJ3GEYJ560V ERJ3GEYJ510V ERJ2GEJ473X ERJ2GEJ104X ERJ2GEJ101X ERJ2GEJ105X ERJ2RHD681X ERJ2GEJ105X ERJ2RHD102X ERJ2RKD240X ERJ2RKD240X ERJ2GEJ153X ERJ2GEJ153X ERJ2GEJ103X ERJ2GEJ103X ERJ2GEJ103X ERJ2GEJ103X ERJ2GE0R00X ERJ2GE0R00X ERJ2GE0R00X ERJ2GEJ103X 68 1/32W 2.2 1/32W 56 1/16W 51 1/16W 47K 1/32W 15K 1/32W 0 1/32W 1K 1/32W 1K 1/32W 22 1/32W 2.2 1/32W 56 1/16W 51 1/16W 47K 1/32W 100K 1/32W 100 1/32W 1M 1/32W 680 1/32W 1M 1/32W 1K 1/32W 24 1/32W 24 1/32W 15K 1/32W 15K 1/32W 10K 1/32W 10K 1/32W 10K 1/32W 10K 1/32W 0 1/32W 0 1/32W 0 1/32W 10K 1/32W [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] RX8001 RX8011 RX8012 RX8013 RX8014 RX8015 RX8016 RX8017 RX8018 RX8019 RX8020 RX8031 RX8032 RX8111 RX8401 RX8402 RX8403 RX8531 RX8532 RX8533 RX8534 RX8611 RX8691 D1H410320002 D1H88204A024 D1H88204A024 D1H88204A024 D1H88204A024 D1H88204A024 D1H88204A024 D1H88204A024 D1H422020001 D1H422020001 D1H422020001 D1H447220001 D1H447220001 D1H422320002 D1H410120001 D1H410120001 D1H410120001 D1H456020001 D1H85604A024 D1H456020001 D1H456020001 D1H447220001 D1H410320002 CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] K4030 ERJ3GEY0R00V CHIP JUMPER K4031 ERJ3GEY0R00V CHIP JUMPER K4032 K8001 ERJ3GEY0R00V ERJ2GE0R00X CHIP JUMPER CHIP JUMPER K8002 K8003 K8004 K8005 K8006 ERJ3GEY0R00V ERJ3GEY0R00V J0JHC0000034 J0JHC0000034 ERJ2GE0R00X CHIP CHIP CHIP CHIP CHIP K8251 K8421 ERJ3GEY0R00V ERJ3GEY0R00V CHIP JUMPER CHIP JUMPER RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR JUMPER JUMPER FERRITE BEAD FERRITE BEAD JUMPER Remarks [M]GC/G S [M]GCS/ GCT [M]GCP [M]GCS/ GCT [M] [M] [M] [M] [M]GCS/ GCT [M] [M] 104 Ref. No. W2201 Part No. Part Name & Description ERJ6GEY0R00V CHIP RESISTOR W2202 ERJ3GEY0R00V CHIP JUMPER W4001 W4002 W4003 W4004 W4005 W4006 W4007 W4011 W4012 W4013 W4014 W4016 W4017 W4018 W4020 W4021 W4022 W4023 W4024 W4025 W4026 W4028 W4034 W4037 W4038 W4039 W4040 W4042 W4043 W4045 W4047 W4048 W4049 W4050 W4053 W4054 W4055 W4056 W4057 W4058 W4059 W4060 W4061 W4062 W4063 W4064 W4065 W4066 W4067 W4068 W4069 W4070 W4071 W4080 W4081 W4082 W4083 W4084 W4085 W4086 W4089 W4090 W4091 W4093 W4094 W4095 W4096 W4100 W6101 ERJ6GEY0R00V ERJ6GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ6GEY0R00V ERJ3GEY0R00V ERJ6GEY0R00V ERJ3GEY0R00V ERJ6GEY0R00V ERJ6GEY0R00V ERJ3GEY0R00V ERJ6GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ6GEY0R00V ERJ6GEY0R00V ERJ6GEY0R00V ERJ3GEY0R00V ERJ6GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ6GEY0R00V ERJ6GEY0R00V ERJ3GEY0R00V ERJ6GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ6GEY0R00V ERJ6GEY0R00V ERJ6GEY0R00V ERJ3GEY0R00V ERJ6GEY0R00V ERJ6GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ6GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ6GEY0R00V ERJ6GEY0R00V ERJ6GEY0R00V ERJ6GEY0R00V ERJ3GEY0R00V ERJ6GEY0R00V ERJ6GEY0R00V ERJ6GEY0R00V ERJ6GEY0R00V ERJ6GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ6GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ6GEY0R00V ERJ3GEY0R00V ERJ6GEY0R00V ERJ6GEY0R00V ERJ6GEY0R00V CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP RESISTOR RESISTOR JUMPER JUMPER JUMPER RESISTOR JUMPER RESISTOR JUMPER RESISTOR RESISTOR JUMPER RESISTOR JUMPER JUMPER RESISTOR RESISTOR RESISTOR JUMPER RESISTOR JUMPER JUMPER RESISTOR RESISTOR JUMPER RESISTOR JUMPER JUMPER JUMPER RESISTOR RESISTOR RESISTOR JUMPER RESISTOR RESISTOR JUMPER JUMPER JUMPER JUMPER JUMPER RESISTOR JUMPER JUMPER JUMPER RESISTOR RESISTOR RESISTOR RESISTOR JUMPER RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR JUMPER JUMPER JUMPER JUMPER JUMPER RESISTOR JUMPER JUMPER JUMPER JUMPER RESISTOR JUMPER RESISTOR RESISTOR RESISTOR Remarks [M]GC/G S [M]GC/G S [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]GC/G S SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS Ref. No. W6102 Part No. Part Name & Description ERJ3GEY0R00V CHIP JUMPER W6502 W6504 W6509 W6511 W6512 W6513 W6514 W6516 W6517 W6545 W6550 W7000 W7001 W7002 ERJ6GEY0R00V ERJ6GEY0R00V ERJ3GEY0R00V ERJ6GEY0R00V ERJ6GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ6GEY0R00V ERJ3GEY0R00V ERJ6GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP RESISTOR RESISTOR JUMPER RESISTOR RESISTOR JUMPER JUMPER RESISTOR JUMPER RESISTOR JUMPER JUMPER JUMPER JUMPER Remarks Ref. No. C2264 C2265 C2272 C2283 C2295 C2300 C2301 C2302 C2303 C2304 C2305 C2306 C2307 C2308 C2309 C2312 C2323 C2324 C2400 C2401 C2402 C2403 C2404 C2405 C2406 C2407 C2408 C2410 C2412 C2423 C2424 C2500 C2501 C2502 C2503 C2506 C2507 C2524 C2600 C2601 C2605 C2606 C2607 C2608 C2609 C2610 C2611 C2612 C2615 C2617 C2619 C2624 C2724 C2800 C2802 C2804 C2805 C2806 C2807 C2808 C2809 C2810 C2811 C2812 C2817 C2818 C2823 C2825 C2826 C2827 C2833 C2841 C2853 [M]GC/G S [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] CAPACITORS C984 C2000 C2001 C2003 C2004 C2006 C2007 C2008 C2009 C2010 C2011 C2012 C2013 C2017 C2018 C2019 C2020 C2021 C2022 C2023 C2024 C2026 C2101 C2111 C2112 C2114 C2115 C2116 C2117 C2118 C2119 C2120 C2121 C2161 C2162 C2164 C2165 C2169 C2172 C2183 C2195 C2201 C2211 C2212 C2214 C2215 C2216 C2217 C2218 C2219 C2220 C2221 C2261 C2262 ECA1EAK100XE ECJ1VB1H104K ECJ1VB1H104K ECA1HM220B ECJ1VB1H103K ECA1HM3R3B ECJ1VB1C104K ECA0JM101B ECJ1VB1H104K ECJ1VB1H331K ECJ1VB1H331K ECJ1VB1H331K ECJ1VB1H223K ECJ1VB1H103K ECA1CM470B ECA1CM470B ECJ1VB1H103K ECA1AM221B ECA1CM101B ECJ1VB1H221K ECJ1VB1H221K ECJ1VB1A105K ECJ1VB1C105K ECJ1VB1C105K ECJ1VB1H471K ECJ1VB1H223K ECJ1VB1H153K ECJ1VB1H472K ECJ1VB1H473K ECJ1VB1C224K ECJ1VB1C105K ECJ1VB1C393K ECJ1VB1H473K ECJ1VB1C183K ECJ1VB1H681K ECJ1VB1H221K ECJ1VB1H102K ECJ1VB1H103K ECJ1VC1H101J ECJ1VB1A105K ECJ1VB1A105K ECJ1VB1C105K ECJ1VB1C105K ECJ1VB1H471K ECJ1VB1H223K ECJ1VB1H153K ECJ1VB1H472K ECJ1VB1H473K ECJ1VB1C224K ECJ1VB1C105K ECJ1VB1C393K ECJ1VB1H473K ECJ1VB1C183K ECJ1VB1H681K 10 25V 0.1 50V 0.1 50V 22 50V 0.01 50V 3.3 50V 0.1 16V 100 6.3V 0.1 50V 330P 50V 330P 50V 330P 50V 0.022 50V 0.01 50V 47 16V 47 16V 0.01 50V 220 10V 100 16V 220P 50V 220P 50V 1 10V 1 16V 1 16V 470P 50V 0.022 50V 0.015 50V 4700P 50V 0.047 50V 0.22 16V 1 16V 0.039 16V 0.047 50V 0.018 16V 680P 50V 220P 50V 1000P 50V 0.01 50V 100P 50V 1 10V 1 10V 1 16V 1 16V 470P 50V 0.022 50V 0.015 50V 4700P 50V 0.047 50V 0.22 16V 1 16V 0.039 16V 0.047 50V 0.018 16V 680P 50V [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] 105 Part No. ECJ1VB1H221K ECJ1VB1H102K ECJ1VC1H101J ECJ1VB1A105K ECJ1VB1A105K ECJ1VB1A105K ECJ1VB1A105K ECJ1VB1C333K ECJ1VB1H473K ECA1CM100B ECJ1VB1H332K ECJ1VB1A105K ECA1CM100B ECJ1VB1H223K ECJ1VB1C823K ECJ1VB1A105K ECJ1VC1H101J ECJ1VB1H222K ECJ1VB1A105K ECJ1VB1A105K ECJ1VB1C333K ECJ1VB1H473K ECA1CM100B ECJ1VB1H332K ECJ1VB1A105K ECA1CM100B ECJ1VB1H223K ECA1CM101B ECJ1VB1A105K ECJ1VC1H101J ECJ1VB1H222K ECJ1VB1A105K ECJ1VB1C105K ECJ1VB1H473K ECJ1VB1H473K ECJ1VB1A105K ECJ1VB1H471K ECJ1VB1H682K ECJ1VB1A105K ECJ1VB1H223K ECJ1VB1H473K ECA1CM100B ECA1HM220B ECA1CM100B ECJ1VB1C224K ECJ1VB1A474K ECJ1VB1H123K ECJ1VB1H332K ECJ1VB1H222K ECJ1VB1A154K ECA1HM100B ECJ1VB1H682K ECJ1VB1H182K ECJ1VB1C105K ECA0JM102B ECJ1VB1C105K ECA0JM331B ECA0JM331B ECJ1VB1H103K ECA1AM221B ECA1AM221B ECJ1VB1H103K ECJ1VB1H104K ECJ1VB1H104K ECJ1VB1C105K ECJ1VB1C105K ECJ1VC1H101J ECJ1VC1H101J ECJ1VC1H101J ECJ1VC1H101J ECA1CM100B ECA0JM102B ECJ1VC1H101J Part Name & Description 220P 50V 1000P 50V 100P 50V 1 10V 1 10V 1 10V 1 10V 0.033 16V 0.047 50V 10 16V 3300P 50V 1 10V 10 16V 0.022 50V 0.082 16V 1 10V 100P 50V 2200P 50V 1 10V 1 10V 0.033 16V 0.047 50V 10 16V 3300P 50V 1 10V 10 16V 0.022 50V 100 16V 1 10V 100P 50V 2200P 50V 1 10V 1 16V 0.047 50V 0.047 50V 1 10V 470P 50V 6800P 50V 1 10V 0.022 50V 0.047 50V 10 16V 22 50V 10 16V 0.22 16V 0.47 10V 0.012 50V 3300P 50V 2200P 50V 0.15 10V 10 50V 6800P 50V 1800P 50V 1 16V 1000 6.3V 1 16V 330 6.3V 330 6.3V 0.01 50V 220 10V 220 10V 0.01 50V 0.1 50V 0.1 50V 1 16V 1 16V 100P 50V 100P 50V 100P 50V 100P 50V 10 16V 1000 6.3V 100P 50V Remarks [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS Ref. No. C2901 C2903 C2910 C2913 C2914 C2919 C2920 C2921 C2922 C2924 C2925 C2952 C2961 C2964 C2967 C2969 C2970 C2975 C2983 C2984 C2985 C2986 C3005 C3006 C3007 C3009 C5101 C5102 C5104 C5105 C5106 C5108 C5124 C5201 C5202 C5204 C5205 C5206 C5208 C5224 C5301 C5302 C5304 C5305 C5306 C5308 C5313 C5324 C5503 C5505 C5790 C5791 C5792 C5794 C5795 C5796 C5797 C5798 C5799 C6093 C6701 C6702 C6703 C6706 C6707 C6708 C6709 C6711 C6805 C6806 C6903 C6904 C6905 Part No. ECA1CM471B ECJ1VB1H103K ECJ1VB1H103K ECA1CM101B ECA1AM330B ECJ1VC1H100D ECJ1VB1H822K ECA1CM471B EEUFC1C471B ECJ1VB1H104K ECA0JM221B ECJ1VB1H104K ECJ1VB1A105K ECJ1VB1A105K ECA0JM102B ECJ1VB1H104K ECJ1VB1H104K ECA1CM101B ECA1CM101B ECJ1VB1H104K ECJ1VB1H103K ECA1HM101B ECJ1VB1A105K ECA1HM100B ECA1HM100B ECA1HM100B ECA1HM100B ECJ1VB1C104K ECJ1VB1H221K ECJ1VB1H221K ECJ1VB1C104K ECA1CM220B ECJ1VB1H104K ECA1HM100B ECJ1VB1C104K ECJ1VB1H471K ECJ1VB1H471K ECJ1VB1C104K ECA1CM220B ECJ1VB1H104K ECA1HM100B ECJ1VB1C104K ECJ1VB1H471K ECJ1VB1H471K ECJ1VB1C104K ECA1CM220B ECA1HM100B ECJ1VB1H104K ECA1VM102B ECJ1VB1H471K ECJ1VB1H102K ECA1CM101B ECA0JM221B ECA1CM330B ECJ1VB1H104K ECA1HM2R2B ECEA1HKA010B ECA1HM101B ECJ1VB1H104K ECJ1VB1H473K ECJ1VB1C105K ECJ1VB1H102K ECJ1VC1H470J ECJ1VB1H104K ECJ1VC1H470J ECJ1VC1H470J ECJ1VB1H104K ECJ1VB1C105K ECJ1VC1H101K ECJ1VC1H101K ECA1HM220B ECJ1VB1H102K ECA1HM220B Part Name & Description 470 16V 0.01 50V 0.01 50V 100 16V 33 10V 10P 50V 8200P 50V 470 16V 470 16V 0.1 50V 220 6.3V 0.1 50V 1 10V 1 10V 1000 6.3V 0.1 50V 0.1 50V 100 16V 100 16V 0.1 50V 0.01 50V 100 50V 1 10V 10 50V 10 50V 10 50V 10 50V 0.1 16V 220P 50V 220P 50V 0.1 16V 22 16V 0.1 50V 10 50V 0.1 16V 470P 50V 470P 50V 0.1 16V 22 16V 0.1 50V 10 50V 0.1 16V 470P 50V 470P 50V 0.1 16V 22 16V 10 50V 0.1 50V 1000 35V 470P 50V 1000P 50V 100 16V 220 6.3V 33 16V 0.1 50V 2.2 50V 1 50V 100 50V 0.1 50V 0.047 50V 1 16V 1000P 50V 47P 50V 0.1 50V 47P 50V 47P 50V 0.1 50V 1 16V 100P 50V 100P 50V 22 50V 1000P 50V 22 50V Remarks Ref. No. C6906 C6909 C6910 C6911 C6913 C6916 C6917 C6918 C6920 C6921 C7101 C7102 C7103 C7104 C7105 C7106 C7107 C7108 C7109 C7110 C7111 C7112 C7113 C7114 C7115 C7116 C7118 C7119 C7120 C8001 C8002 C8003 C8004 C8005 C8006 C8007 C8008 C8011 C8012 C8013 C8014 C8015 C8016 C8018 C8020 C8021 C8022 C8026 C8051 C8052 C8053 C8054 C8055 C8056 C8057 C8111 C8112 C8113 C8151 C8152 C8201 C8202 C8203 C8211 C8221 C8222 C8225 C8226 C8231 C8232 C8251 C8252 C8253 [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] 106 Part No. ECJ1VC1H101K ECJ1VB1H103K ECA0JM101B ECJ1VB1H103K ECA1HM3R3B ECJ1VC1H101K ECJ1VC1H101K ECA1AM470B ECJ1VB1C105K ECJ1VB1H221K ECEA1HKA010B ECJ1VB1H682K ECJ1VB1H152K ECJ1VB1C683K ECJ1VB1C224K ECJ1VB1C224K ECJ1VB1H682K ECJ1VB1H152K ECJ1VB1C683K ECA1CM470B ECA1CM470B ECJ1VB1H104K ECEA1HKA010B ECJ1VC1H470J ECJ1VB1H221K ECJ1VB1H104K ECJ1VB1H104K ECA1HM2R2B ECJ1VB1H153K EEE0GA331WP ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EF1C104Z F2G0J101A066 ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EF1C104Z ECJ1VB0J105K ECJ0EB1A104K ECJ0EF1C104Z ECJ0EC1H221J ECJ1VB0J105K ECJ0EB1E222K ECJ1VB0J105K ECJ0EB1A104K ECJ1VB0J105K ECJ0EB1E471K ECJ1VB0J475K ECJ1VB1C105K F2G0J101A066 ECJ0EB1A104K ECJ0EB1A104K ECJ0EB1E122K ECJ0EB1E102K ECJ0EB1E102K ECJ0EB1E102K ECJ0EB1E821K ECJ0EB1A104K ECJ0EB1A104K F2G0J221A065 ECJ0EF1C104Z ECJ0EF1C104Z Part Name & Description 100P 50V 0.01 50V 100 6.3V 0.01 50V 3.3 50V 100P 50V 100P 50V 47 10V 1 16V 220P 50V 1 50V 6800P 50V 1500P 50V 0.068 16V 0.22 16V 0.22 16V 6800P 50V 1500P 50V 0.068 16V 47 16V 47 16V 0.1 50V 1 50V 47P 50V 220P 50V 0.1 50V 0.1 50V 2.2 50V 0.015 50V 330 4V 0.1 16V 0.1 16V 0.1 16V 0.1 16V 0.1 16V 0.1 16V 0.1 16V 100 6.3V 0.1 16V 0.1 16V 0.1 16V 0.1 16V 0.1 16V 0.1 16V 0.1 16V 0.1 16V 0.1 16V 0.1 16V 1 6.3V 0.1 10V 0.1 16V 220P 50V 1 6.3V 2200P 25V 1 6.3V 0.1 10V 1 6.3V 470P 25V 4.7 6.3V 1 16V 100 6.3V 0.1 10V 0.1 10V 1200P 25V 1000P 25V 1000P 25V 1000P 25V 820P 25V 0.1 10V 0.1 10V 220 6.3V 0.1 16V 0.1 16V Remarks [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] SA-PT150GC / SA-PT150GCP / SA-PT150GCS / SA-PT150GCT / SA-PT150GS Ref. No. C8254 C8255 C8256 C8257 C8258 C8261 C8262 C8263 C8301 C8302 C8303 C8304 C8305 C8306 C8311 C8312 C8313 C8320 C8321 C8325 C8330 C8331 C8335 C8340 C8341 C8401 C8402 C8421 C8422 C8423 C8424 C8426 C8427 C8428 C8429 C8430 C8501 C8502 C8503 C8504 C8505 C8511 C8512 C8513 C8514 C8515 C8516 C8521 C8522 C8523 C8524 C8525 C8526 C8527 C8528 C8529 C8530 C8531 C8532 C8533 C8541 C8550 C8551 C8552 C8553 C8554 C8561 C8562 C8563 C8564 C8571 C8572 C8601 Part No. ECJ0EF1C104Z F2G1C220A037 ECJ0EF1C104Z F2G1C470A076 ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EF1C104Z ECJ1VB1H221K F2G0J221A031 F2G0J330A031 ECJ0EB1A104K ECJ0EB1A104K ECJ0EB1A104K ECJ0EB1A104K ECJ0EB1A104K ECJ1VB0J105K ECJ1VB0J105K ECJ0EF1C104Z ECJ0EB1A104K ECJ0EB1A104K F2G0J470A031 ECJ0EB1A104K ECJ0EB1A104K ECJ0EF1C104Z ECJ0EB1A104K ECJ0EC1H150J ECJ0EC1H150J F2G0J101A083 ECJ0EF1C104Z F2G0J330A083 ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EF1C104Z F2G0J470A031 F2G0J101A031 ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EF1C104Z ECJ1VB0J105K ECJ1VB0J105K ECJ0EB1A104K ECJ0EB1A104K ECJ0EB1A104K ECJ0EB1A104K ECJ0EB1A104K ECJ0EB1A104K ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EB1C562K ECJ0EB1C183K ECJ0EB1A333K ECJ1VB0J105K ECJ1VB0J105K ECJ0EF1C104Z ECJ0EC1H101J ECJ0EC1H221J ECJ0EF1C104Z ECJ0EB1E472K F2G0J330A031 ECJ0EF1C104Z F2G1C100A072 F2G0J470A031 ECJ1VB0J105K ECJ0EF1C104Z F2G1C100A072 F2G0J470A031 ECJ1VB0J105K ECJ3YB1A106M ECJ0EF1C104Z ECJ0EF1C104Z Part Name & Description 0.1 16V 22 16V 0.1 16V 47 16V 0.1 16V 0.1 16V 0.1 16V 220P 50V 220 6.3V 33 6.3V 0.1 10V 0.1 10V 0.1 10V 0.1 10V 0.1 10V 1 6.3V 1 6.3V 0.1 16V 0.1 10V 0.1 10V 47 6.3V 0.1 10V 0.1 10V 0.1 16V 0.1 10V 15P 50V 15P 50V 100 6.3V 0.1 16V 33 6.3V 0.1 16V 0.1 16V 0.1 16V 0.1 16V 0.1 16V 47 6.3V 100 6.3V 0.1 16V 0.1 16V 0.1 16V 0.1 16V 1 6.3V 1 6.3V 0.1 10V 0.1 10V 0.1 10V 0.1 10V 0.1 10V 0.1 10V 0.1 16V 0.1 16V 5600P 16V 0.018 16V 0.033 10V 1 6.3V 1 6.3V 0.1 16V 100P 50V 220P 50V 0.1 16V 4700P 25V 33 6.3V 0.1 16V 10 16V 47 6.3V 1 6.3V 0.1 16V 10 16V 47 6.3V 1 6.3V 10 10V 0.1 16V 0.1 16V Remarks [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] 107 Ref. No. C8602 C8606 C8611 C8621 C8622 C8651 C8652 C8691 C8695 C9004 C9005 C9006 C9007 C9008 Part No. Part Name & Description ECJ0EB1C153K ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EC1H120J ECJ0EC1H120J ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EF1C104Z ECJ0EC1H070D ECJ0EC1H070D ECJ0EB1A104K ECJ0EF1C104Z ECJ1VB0J105K 0.015 16V 0.1 16V 0.1 16V 12P 50V 12P 50V 0.1 16V 0.1 16V 0.1 16V 0.1 16V 7P 50V 7P 50V 0.1 10V 0.1 16V 1 6.3V C9008 ECJ1VB1C105K 1 16V C9018 ECJ0EB1A104K 0.1 10V Remarks [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M] [M]GCS/ GCT [M]GC/G SGCP [M] MMH0705
Similar documents
table of contents - Support | Panasonic
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30 degrees C (662±86°F). Recommended Lead Free Solder (Service Parts Route.) • Th...
More informationModel No. SA-MAX500LMK
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30 degrees C (662±86qF). Recommended Lead Free Solder (Service Parts Route.) • Th...
More informationModel No. SA-AKX32LM-K
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30 degrees C (662±86!F). Recommended Lead Free Solder (Service Parts Route.) • Th...
More informationAKAI PDP4206EM Service Manual
outlet and repeat the AC voltage measurements for each exposed metallic part. The measured voltage must not exceed 0.3V
More informationSA-AK640E SA-AK640EB SA-AK640EG
Some semiconductor (solid state) devices can be damaged easily by electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integ...
More information