SERVICE MANUAL

Transcription

SERVICE MANUAL

DSC-W150/W170
SERVICE MANUAL
LEVEL
Ver. 1.2 2009.06
Revision History
Internal memory
ON BOARD
Revised-1
Replacement of the previously issued
SERVICE MANUAL 9-852-296-32
with this manual.
Photo: DSC-W150/Silver
2
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Argentine Model
Brazilian Model
Thai Model
Japanese Model
Tourist Model
Link
SPECIFICATIONS
DISASSEMBLY
SCHEMATIC DIAGRAMS
MODEL INFORMATION TABLE
BLOCK DIAGRAMS
PRINTED WIRING BOARDS
SERVICE NOTE
FRAME SCHEMATIC DIAGRAM
REPAIR PARTS LIST
• Precaution on Replacing the SY-194 Board
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
DIGITAL STILL CAMERA
DSC-W150/W170_L2
9-852-296-33
Sony EMCS Co.
2009F0500-1
© 2009.6
Published by Kohda TEC
SPECIFICATIONS
Camera
[System]
Image device:
DSC-W170:
7.70 mm (1/2.3 type) color CCD,
Primary color filter
DSC-W150:
7.18 mm (1/2.5 type) color CCD,
Primary color filter
Total pixel number of camera:
DSC-W170:
Approx. 10.3 Megapixels
DSC-W150:
Effective pixel number of camera:
DSC-W170:
DSC-W150:
Lens:
DSC-W170:
Carl Zeiss Vario-Tessar 5× zoom lens
f = 5 - 25 mm (28 - 140 mm (35 mm film
equivalent)) F3.3(W) - 5.2(T)
DSC-W150:
Carl Zeiss Vario-Tessar 5× zoom lens
f = 5 - 25 mm (30 - 150 mm (35 mm film
equivalent)) F3.3(W) - 5.2(T)
Exposure control: Automatic exposure, Scene
Selection (10 modes)
White balance: Automatic, Daylight, Cloudy,
Fluorescent 1,2,3, Incandescent, Flash
Underwater White Balance: Auto, Underwater
1,2, Flash
File format (DCF compliant):
Still images: Exif Ver. 2.21 JPEG compliant,
DPOF compatible
Movies: MPEG1 compliant (Monaural)
Recording media: Internal Memory (approx.
15 MB), “Memory Stick Duo”
Flash:Flash range (ISO sensitivity
(Recommended exposure Index) set to Auto):
Approx. 0.2 to 4.2 m (7 7/8 inches to 13 feet
9 3/8 inches) (W)/approx. 0.5 to 2.7 m (1 foot
7 3/4 inches to 8 feet 10 3/8 inches) (T)
[Input and Output connectors]
Multi connector: Video output
Audio output (Monaural)
USB communication
USB communication: Hi-Speed USB (USB 2.0
compliant)
[LCD screen]
LCD panel: 6.7 cm (2.7 type) TFT drive
Total number of dots: 230 400 (960 × 240) dots
[Power, general]
Power: Rechargeable battery pack
NP-BG1, 3.6 V
NP-FG1 (not supplied), 3.6 V
AC-LS5K AC Adaptor (not supplied), 4.2 V
Power consumption (during shooting, LCD screen
on): 1.0 W
Operating temperature: 0 to 40°C (32 to 104°F)
Storage temperature: –20 to +60°C (–4 to +140°F)
Dimensions: 93.7 × 58.0 × 24.0 mm (3 3/4 ×
2 3/8 × 31/32 inches) (W/H/D, excluding
protrusions)
Mass: Approx. 175 g (6.2 oz) (including NP-BG1
battery pack, strap, etc.)
Microphone: Monaural
Speaker: Monaural
Exif Print: Compatible
PRINT Image Matching III: Compatible
PictBridge: Compatible
DSC-W150/W170_L2
—2—
BC-CSGB/BC-CSGC battery
charger
Power requirements: AC 100 V to 240 V, 50/60 Hz,
2.6 W (BC-CSGB)/2 W (BC-CSGC)
Output voltage: DC 4.2 V, 0.25 A
Operating temperature: 0 to 40°C (32 to 104°F)
Storage temperature: –20 to +60°C (–4 to +140°F)
Dimensions: Approx. 62 × 24 × 91 mm (2 1/2 ×
31/32 × 3 5/8 inches) (W/H/D)
Mass: Approx. 75 g (2.7 oz)
Rechargeable battery pack NPBG1
Used battery: Lithium-ion battery
Maximum voltage: DC 4.2 V
Nominal voltage: DC 3.6 V
Capacity: 3.4 Wh (960 mAh)
Design and specifications are subject to change
without notice.
Ver. 1.1 2008.05
The changed portions from
Ver. 1.0 are shown in blue.
Model information table
Model
Destination
CD board
DSC-W150
DSC-W170
US, CND, AEP, UK,
E, AUS, HK, CH,
KR, AR, BR, TH, JE
CD-732
US, CND, AEP, UK,
E, AUS, HK, CH,
KR, AR, BR, TH, J
CD-733
• Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
EE : East European model
HK : Hong Kong model
J
: Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
TH : Thai model
DSC-W150/W170_L2
—3—
ENGLISH
JAPANESE
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1.
2.
3.
4.
5.
6.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
Check the B+ voltage to see it is at the values specified.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
DSC-W150/W170_L2
—4—
ENGLISH
JAPANESE
注意
電池の交換は，正しく行わないと破裂する恐れがあり
ます。電池を交換する場合には必ず同じ型名の電池
又は同等品と交換してください。
サービス，点検時には次のことにご注意下さい。
6. フレキシブルプリント基板の取扱いについて
1. 注意事項をお守りください。
サービスのとき特に注意を要する個所については，
キャビネット，シャーシ，部品などにラベルや捺印で
• コテ先温度を270℃前後にして行なって下さい。
• 同一パターンに何度もコテ先を当てないで下さい。
注意事項を表示しています。これらの注意書き及び取
扱説明書等の注意事項を必ずお守り下さい。
（3回以内）
• パターンに力が加わらないよう注意して下さい。
2. 指定部品のご使用を
セットの部品は難燃性や耐電圧など安全上の特性を
7. 無鉛半田について
無鉛半田を使用している基板には，無鉛（Lead Free）を意
持ったものとなっています。従って交換部品は，使用
されていたものと同じ特性の部品を使用して下さい。
味するレッドフリーマークがプリントされています。
（注意：基板サイズによっては，無鉛半田を使用して
特に回路図，部品表に0印で指定されている安全上重要
な部品は必ず指定のものをご使用下さい。
いてもレッドフリーマークがプリントされて
いないものがあります）
3. 部品の取付けや配線の引きまわしはもとどおりに
安全上，チューブやテープなどの絶縁材料を使用した
：レッドフリーマーク
無鉛半田には，以下の特性があります。
り，プリント基板から浮かして取付けた部品がありま
す。また内部配線は引きまわしやクランパによって発
• 融点が従来の半田よりも約40℃高い。
従来の半田こてをそのまま使用することは可能です
熱部品や高圧部品に接近しないよう配慮されています
ので，これらは必ずもとどおりにして下さい。
が，少し長めにこてを当てる必要があります。
温度調節機能のついた半田こてを使用する場合，約
4. サービス後は安全点検を
サービスのために取外したネジ，部品，配線がもとど
350℃に設定して下さい。
注意：半田こてを長く当てすぎると，基板のパター
おりになっているか，またサービスした個所の周辺を
劣化させてしまったところがないかなどを点検し，安
ン（銅箔）がはがれてしまうことがあります
ので，注意して下さい。
• 粘性が強い
従来の半田よりも粘性が強いため，IC端子などが半田
全性が確保されていることを確認して下さい。
5. チップ部品交換時の注意
• 取外した部品は再使用しないで下さい。
• タンタルコンデンサのマイナス側は熱に弱いため交
ブリッジしないように注意して下さい。
• 従来の半田と混ぜて使用可能
無鉛半田には無鉛半田を追加するのが最適ですが，
従来の半田を追加しても構いません。
換時は注意して下さい。
DSC-W150/W170_L2
—5—
1. SERVICE NOTE
ENGLISH
JAPANESE
1-1. PRECAUTION ON REPLACING THE SY-194 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Refer to Service Manual ADJ, and perform “DESTINATION DATA WRITE”.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Refer to Service Manual ADJ, and perform “USB SERIAL No. INPUT”.
1-2. SELF-DIAGNOSIS FUNCTION
1-2-1. Self-diagnosis Function
1-2-2. Self-diagnosis Display
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the LCD screen what to
do.
Details of the self-diagnosis functions are provided in the Instruction
manual.
When problems occur while the unit is operating, the LCD screen
shows a 4-digit display consisting of an alphabet and numbers, which
blinks at 3.2 Hz. This 5-character display indicates the “repaired
by:”, “block” in which the problem occurred, and “detailed code”
of the problem.
LCD screen
Blinks at 3.2 Hz
C
Repaired by:
32
Block
00
Detailed Code
Refer to “1-2-3. Self-diagnosis Code Table”.
C : Corrected by customer Indicates the appropriate
E : Corrected by service
step to be taken.
engineer
E.g.
13 ....Format the “Memory Stick Duo”.
32 ....Turn on power again.
DSC-W150/W170_L2
1-1
ENGLISH
JAPANESE
1-2-3. Self-diagnosis Code Table
Repaired by:
Self-diagnosis Code
Block
Function
Detailed
Code
C
1
3
0
1
C
3
2
0
1
E
6
1
0
0
E
6
1
1
0
E
6
2
0
2
E
6
2
1
0
E
6
2
1
1
E
6
2
1
2
E
6
2
2
0
E
E
9
9
1
2
0
0
1
0
Symptom/State
Correction
The internal memory has experienced a
format error.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
“Memory Stick Duo” type error
The camera cannot read or write data
on the “Memory Stick Duo”.
Trouble with hardware
Format the internal memory.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Insert a supported “Memory Stick Duo”.
Turn the power off and on again, or taking out and inserting the
“Memory Stick Duo” several times.
Turn the power off and on again.
Retry turn the power on by the power switch. If it does not
recover, check the focus reset sensor of lens block (pin rj of
Difficult to adjust focus
(Cannot initialize focus)
CN401 on the SY-194 board). If it is OK, check the focus motor
drive IC (IC401 on the SY-194 board).
Retry turn the power on by the power switch. Check the zoom
reset sensor of lens block (pin t; of CN401 on the SY-194
Zoom operations fault
board) when zooming is performed when the zoom button is
(Cannot initialize zoom lens.)
operated. If it is OK, check the zoom motor drive IC (IC401 on
the SY-194 board).
Check or replacement of the IC for steadyshot (IC503 on the SYAbnormality of IC for steadyshot.
194 board).
Check or replacement of the IC for steadyshot (IC503 on the SYLens initializing failure.
194 board).
Check the HALL element (PITCH) of optical image stabilizer
(pin qj, ql of CN401 on the SY-194 board). If it is OK, check
Lens overheating (PITCH).
PITCH angular velocity sensor (SE502 on the SY-194 board)
peripheral circuits.
Check the HALL element (YAW) of optical image stabilizer (pin
q;, qs of CN401 on the SY-194 board). If it is OK, check YAW
Lens overheating (YAW).
angular velocity sensor (SE501 on the SY-194 board) peripheral
circuits.
Check the OIS temp sensor of optical image stabilizer (pin qg of
Abnormality of thermistor.
CN401 on the SY-194 board).
Abnormality when flash is being charged. Checking of flash unit or replacement of flash unit. (Note)
Non-standard battery is used.
Use the compatible battery only.
Note: After repair, be sure to perform “1-3. PROCESS AFTER FIXING FLASH ERROR”.
DSC-W150/W170_L2
1-2
ENGLISH
JAPANESE
1-3. PROCESS AFTER FIXING FLASH ERROR
When “FLASH error” (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash
is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the HOME screen.
Method for Initializing the Flash Error Code
Initialize
Initializes the setting to the default setting. Even if you execute this function, the images
stored in the internal memory are retained.
1 Select [Initialize] with v/V on the control button, then press z.
The message “Reset to default settings” appears.
2 Select [OK] with v, then press z.
The settings are reset to the default setting.
To cancel initializing
Select [Cancel] in step 2, then press z.
• Be sure not to power off the camera while initializing.
1-4. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the internal memory.)
Note 1: When replacing the SY-194 board, erase the data in internal memory of the board before replacement.
Note 2: When replacing the SY-194 board, execute formatting and initialize the internal memory after replacement.
Method for Copying the Data in Internal Memory
Copy
Copies all images in the internal memory to a “Memory Stick Duo”.
1 Insert a “Memory Stick Duo” having sufficient free capacity.
2 Select [Copy] with v/V on the control button, then press z.
The message “All data on internal memory will be copied” appears.
Copying starts.
To cancel copying
• Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little
remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.
• You cannot select images to copy.
• The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the “Memory Stick Duo” after copying, then format the internal memory
([Format] in [Internal Memory Tool]).
• A new folder is created on the “Memory Stick Duo” and all the data will be copied to it. You cannot
choose a specific folder and copy images to it.
• The
(Print order) marks on the images are not copied.
Method for Formatting the Internal Memory
This item does not appear when a “Memory Stick Duo” is inserted in the camera.
Format
Formats the internal memory.
• Note that formatting permanently erases all data in the internal memory, including even protected images.
1 Select [Format] with v/V on the control button, then press z.
The message “All data on internal memory will be erased” appears.
Formatting starts.
To cancel formatting
DSC-W150/W170_L2
1-3
ENGLISH
JAPANESE
1-5. HOW TO WRITE DATA TO INTERNAL MEMORY
Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera.
This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement.
To change the setting, use the write enable tool “WriteEnableTool.exe”.
Data writing method
1)
2)
3)
Connect the PC to the camera (USB mode: Mass Storage), and switch the driver to the “Sony Seus USB Driver”.
Start the Write Enable Tool and the SeusEX.
Click the [Activate Write Enable Mode] button of the Write Enable Tool.
4)
Upon completion of the setting change, the following message will be displayed.
5)
6)
7)
Return the driver to the original one, and connect the PC to the camera (USB mode: Mass Storage).
Write the data read out into the PC to the internal memory of the camera.
Disconnect the PC from the camera, and turn off the camera.
Note: By turning off the camera, the write enable setting is reset.
DSC-W150/W170_L2
1-4
1. SERVICE NOTE
ENGLISH
JAPANESE
1-1. SY-194基板交換時の注意
仕向けデータ
補修用基板と交換する時，補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。
ADJ編を参照して，「DESTINATION DATA WRITE」を行ってください。
USBシリアルNo.
セットは，1台毎に異なる固有のID（USB Serial No.）を書き込んだ後，出荷されています。
新品の補修用基板には，このIDが書き込まれていないので，基板交換後にIDを入力する必要があります。
ADJ編を参照して，「USB SERIAL No. INPUT」を行ってください。
1-2. 自己診断機能
1-2-2. 自己診断表示
本機の動作に不具合が生じたとき，LCD画面にアルファベッ
1-2-1. 自己診断機能について
本機の動作に不具合が生じたとき，自己診断機能が働き，
L C D 画面に，どう処置したらよいか判断できる表示を行い
トと4桁の数字が表示され，3.2Hzで点滅します。この5文字
の表示によって対応者分類および不具合の生じたブロックの
ます。自己診断機能については取扱説明書にも掲載されて
います。
分類，不具合の詳細コードを示します。
LCD画面
C : 3 2 : 00
3.2Hz点滅
C
対応者分類
C ：お客さま自身で対応
E ：サービスエンジニア
で対応
32
ブロック分類
00
詳細コード
「1 -2 -3 . 自己診断コード表」
対応方法の違いにより分類
例 13 ･･･“メモリースティックを参照
デュオ”をフォーマッ
トする
32 ･･･電源を入れ直す
DSC-W150/W170_L2
1-5
ENGLISH
JAPANESE
1-2-3. 自己診断コード表
自己診断コード
対ブロック
応
機能
者
詳細
コード
C
0
1
3
1
症状／状態
対応／方法
内蔵メモリにフォーマットエラーが内蔵メモリをフォーマットする。
あった。
フォーマットしていない“メモリー “メモリースティックデュオ”をフォーマットする。
スティックデュオ”を入れた。
“メモリースティックデュオ”が
壊れている。
新しい“メモリースティックデュオ”に交換する。
“メモリースティックデュオ”の
タイプエラーを検出した。
規格内の“メモリースティックデュオ”を挿入する。
“メモリースティックデュオ”が
読み／書きできない。
電源の入れ直し，または“メモリースティックデュオ”
の挿し／外しを数回試す。
C
3
2
0
1
ハードウェアトラブルを検出した。電源を入れ直す。
E
6
1
0
0
フォーカスが合いにくい。
操作スイッチの電源を入れ直す。
（フォーカスの初期化ができない）復帰しない場合はレンズブロックのフォーカスリセットセ
ンサ（SY-194基板CN401 rjピン）を点検する。異常なけ
ればフォーカスモータ駆動IC（SY-194基板IC401）を点検
する。
E
6
1
1
0
ズーム動作の異常。
操作スイッチの電源を入れ直す。
（ズームレンズの初期化ができな
い）
ズームボタンを操作したときにズーム動作をすればレンズ
ブロックのズームリセットセンサ（SY-194基板CN401 t;
ピン）を点検する。異常なければズームモータ駆動IC
（SY-194基板IC401）を点検する。
E
6
2
0
2
手振れ補正用ICの異常。
手振れ補正用IC（SY-194基板IC503）を点検または交換す
る。
E
6
2
1
0
手振れ補正用ICの異常。
（レンズ初期化異常）
手振れ補正用IC（SY-194基板IC503）を点検または交換す
る。
E
6
2
1
1
レンズオーバーヒート（PITCH）
光学手振れ補正ブロックのホール素子（PITCH）（SY-194
基板CN401 qj，qlピン）を点検する。異常なければ
PITCH角速度センサ（SY-194基板SE502）周辺の回路を点
検する。
E
6
2
1
2
レンズオーバーヒート（YAW）
光学手振れ補正ブロックのホール素子（YAW）（SY-194
基板CN401 q;，qsピン）を点検する。異常なければYAW
角速度センサ（SY-194基板SE501）周辺の回路を点検す
る。
E
6
2
2
0
サーミスタの異常。
光学手振れ補正ブロックの温度センサ（SY-194基板CN401
qgピン）を点検する。
E
9
1
0
1
フラッシュの充電異常。
フラッシュユニットを点検または交換する。（Note）
E
9
2
0
0
規定外の充電池が使用された。
規定の充電池を使用する。
Note：交換後は，必ず「1-3. フラッシュエラー発生時の対処法」を行って下さい。
DSC-W150/W170_L2
1-6
ENGLISH
JAPANESE
1-3. フラッシュエラー発生時の対処法
本機はフラッシュエラー（自己診断コードE：91：01）が発生した場合，高電圧による異常を防止するために自動的にフラッシュ
充電および発光禁止の設定になります。
フラッシュエラー発生後はエラーの解除を行う必要があります。エラーの解除はホーム画面から初期化操作を実行することによ
り行います。
設定リセット
お買い上げ時の設定に戻します。
［設定リセット］を実行しても、内蔵メモリーに記録されている画像は削除されません。
1 コントロールボタンの v/ V で［設定リセット］を選び、中央の z を押す。
「全ての設定内容をリセットします」というメッセージが表示される。
2 v で［実行］を選び、中央の z を押す。
設定リセットが実行される。
設定リセットを中止するには
手順 2 で、
［キャンセル］を選び、中央の z を押す。
•
設定リセット中は電源が切れないようにご注意ください。
1-4. 内蔵メモリのデータコピーおよび消去方法
内蔵メモリのデータコピーまたは消去はホーム画面の操作から実行可能です。（消去する場合は内蔵メモリの初期化を行いま
す。）
Note1： SY-194基板交換の際は，基板交換前に内蔵メモリのデータを消去して下さい。
Note2： SY-194基板交換の際は，基板交換後に内蔵メモリのフォーマットおよび初期化を実行して下さい。
内蔵メモリのコピー方法
コピー
内蔵メモリーに記録した画像を、
“メモリースティックデュオ”に一括コピーします。
1 充分な空き容量のある“メモリースティックデュオ”を本体に入れる。
2 コントロールボタンの v/ V で［コピー］を選び、中央の z を押す。
「内蔵メモリーのデータがすべてコピーされます」というメッセージが表示される。
3 v で［実行］を選び、中央の z を押す。
コピーが実行される。
コピーを中止するには
手順 3 で、
［キャンセル］を選び、中央の z を押す。
•
充分に充電したバッテリーをご使用ください。残量の少ないバッテリーを使用して画像ファイ
ルをコピーすると、バッテリー切れのためデータを転送できなかったり、データを破損するお
それがあります。
•
画像ごとのコピーはできません。
•
データをコピーしても、内蔵メモリー内のデータは削除されません。内蔵メモリーの内容を消
去するには、コピー後に“メモリースティックデュオ”を本体から取りはずし、
［内蔵メモリー
ツール］の［フォーマット］を行ってください。
•
データをコピーすると“メモリースティックデュオ”内に新しいフォルダが作成されます。コ
ピー先のフォルダを指定することはできません。
•
データのコピーを行っても、
（プリント予約）マークの設定はコピーされません。
内蔵メモリのフォーマット方法
“メモリースティックデュオ”
が本機に入っている場合は表示されません。
フォーマット
内蔵メモリーの管理領域をフォーマット
（初期化）します。
•
フォーマットすると、プロテクトしてある画像も含めて、すべてのデータが消去され、元に戻せ
ません。
1 コントロールボタンの v/ V で［フォーマット］
を選び、中央の z を押す。
「内蔵メモリーのデータがすべて消去されます」というメッセージが表示される。
2 vで［実行］を選び、中央の z を押す。
フォーマットが実行される。
フォーマットを中止するには
手順 2 で、
［キャンセル］
を選び、中央の z を押す。
DSC-W150/W170_L2
1-7
ENGLISH
1-5. 内蔵メモリへデータを書き戻す方法
通常は，PCからカメラの内蔵メモリへデータを書き込むことはできない設定になっています。
基板交換後などに，内蔵メモリへデータを書き戻す場合には，この設定を一時的に変更する必要があります。
設定の変更には，書き込み許可ツール（WriteEnableTool.exe）を使用します。
書き戻し方法
1) カメラとPCをマスストレージ接続し，ドライバを“Sony Seus USB Driver”に切り替える。
2) 書き込み許可ツールとSeusEXを起動する。
3) 書き込み許可ツールの[Activate Write Enable Mode]ボタンをクリックする。
4)
設定の変更が終了すると，次のメッセージが表示されます。
5)
6)
7)
ドライバを元に戻して、カメラとPCをマスストレージ接続する。
PCに読み出しておいたデータをカメラの内蔵メモリに書き込む。
カメラとPCの接続を解除し，カメラの電源をOFFにする。
注意：カメラの電源をOFFにすることにより，書き込み許可の設定が解除されます。
DSC-W150/W170_L2
1-8E
JAPANESE
2. DISASSEMBLY
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
DISCHARGING OF THE CHARGING CAPACITOR (C901)
The charging capacitor (C901) is charged up to the maximum
300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points
with the short jig about 10 seconds.
R:1 kΩ/1 W
(Part code: 1-215-869-11)
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 kΩ /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
1 kΩ/1 W
C901
Wrap insulating tape.
DSC-W150/W170_L2
2-1
2-1. IDENTIFYING PARTS
Cabinet (Rear)
Cabinet (Upper)
⋅ AF-113 Board
⋅ ST-180 Board
BT Holder
⋅ FP-866 Flexible Board
⋅ MC-191 Flexible Board
⋅ SY-194 Board
LCD
Main Frame
⋅ SW-529 Board
⋅ SW-533 Flexible Board
Cabinet (Front)
Lens Block
⋅ CCD Block (CD-732/733 Flexible Board)
- DISASSEMBLY FLOW 2-2-1. CABINET SECTION
⋅ Cabinet (Rear)
⋅ Cabinet (Front)
2-2-2. MAIN FRAME SECTION
⋅ LCD
⋅ Lens Block
2-2-3. BT HOLDER SECTION
⋅ Cabinet (Upper)
⋅ SY-194 Board
DSC-W150/W170_L2
2-2
HELP
2-2. DISASSEMBLY
EXPLODED VIEW
HARDWARE LIST
2-2-1. CABINET SECTION
Follow the disassembly in the numerical order given.
1 Cabinet (Rear) (1-1 to 1-4)
2 Cabinet (Front) (2-1 to 2-6)
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points
with the short jig about 10 seconds.
R:1 kΩ/1 W
(Part code: 1-215-869-11)
C901
1 Cabinet (Rear)
1-2 (#20)
HELP 1
2-1
2-6 (#20)
1-4
(Boss)
1-3 (#20)
1-1 (#20)
2 Cabinet (Front)
2-3 (#20)
2-4 (#3)
2-2
Main Frame Section
(See page 2-4)
2-5 (#20)
DSC-W150/W170_L2
2-3
EXPLODED VIEW
HARDWARE LIST
1 LCD (1-1 to 1-13)
2 Lens Block (2-1 to 2-11)
1 LCD
1-8 (Solder)
1-7
1-11
HELP 2
1-5
1-3 (Claw)
1-4
1-10 (Claw)
1-6
1-9 (Claw)
1-13 (Claw)
1-12 (Claw)
1-2
1-1
(#20)
2-4
2-2
HELP 3
2-10
2-9
BT Holder Section
(See page 2-5)
2-1 (#20)
2-11
2-3
2-7 (Boss)
HELP 3
2-6
2-5 (Claw)
HELP 3
2-8
HELP 3
DSC-W150/W170_L2
2-4
2Lens Block
EXPLODED VIEW
HARDWARE LIST
1 Cabinet (Upper) (1-1 to 1-5)
2 SY-194 Board (2-1 to 2-5)
2SY-194 Board
1 Cabinet (Upper)
HELP 4
1-1
1-5
HELP 5
2-1
2-5
(#3)
(Solder)
2-2 (Claw)
1-4 (Claw)
HELP 6
1-3 (Claw)
1-2
(#20)
HELP 7
2-3 (Claw)
DSC-W150/W170_L2
2-5
2-4
2-3. BARRIER ASSY REPLACING METHOD
Removal
1 Turn on the power switch and extend the lens up to the TELE end.
2 Detach the battery.
3 Insert the edge of nippers from the inner diameter into A or B of the Ornamental Ring (A) to make a cut in till the outside.
4 Pinch either of the parted surfaces and wind it up to peel the flat surface on the objective side.
Note: Applying a load to the lens barrel could affect the lens zoom-in operation. Do not apply a load to the lens barrel.
A
B
5 Utilizing a concave portion of the Barrier Assy, insert the edge of nippers into the side surface to make a cut in and wind it up
to peel about 2/3 (about 10mm; approximately second convex).
Note: Mask the second lens barrel to prevent damage.
Convex
Concave
10mm
Second lens barrel
6 Wind a rubber around the remaining part of the Ornamental Ring (A) and apply torque to peel the part that remains inside and
at the hem.
Ornamental Ring (A)
Rubber
7 Disengage three claws, and remove the Barrier Assy.
Claws
Barrier Assy
DSC-W150/W170_L2
2-6
Installation
1 With three claws fitted in position, install the Barrier Assy.
Claws
Barrier Assy
2 Remove adhesive agent remaining on the side surface of the group-1 frame.
3 Apply adhesive agent to two places of the first convex on the side surface in 3-4 o'clock and 9-10 o'clock directions.
Adhesive agent: Super X (white) or equivalents
Amount of application: 2-3 cubic millimeters per place
Adhesive agent
Convex
4 Install new Ornamental Ring (A)
Note: When the Ornamental Ring (A) passed the second convex, if extra adhesive agent remains on the end surface of the ring,
wipe it off and push in the ring until it is stopped.
5 Wait for the adhesive agent to harden.
Hardening time: About 20 minutes
Ornamental Ring (A)
Adhesive agent
DSC-W150/W170_L2
2-7
2-4. ZOOM MOTOR REPLACING METHOD
2-4-1. Zoom Gear Block Replacing Method
Removal
1 Remove one screw.
2 Break solders.
3 Remove the Zoom Gear Block.
4 Remove the Naruto Gear.
4 Naruto Gear
2 Solders
1 Screw
3 Zoom Gear Block
Installation
1 Confirm the lens barrel is stored.
2 Confirm the direction of the Naruto Gear and install it.
1
Adjust convex part to the CCD side.
2 Naruto Gear
3 Install the Zoom Gear Block after matching the position of boss.
4 Solder the flexible board of Zoom Gear Block.
5 Tighten one screw.
* Tightening torque = 0.098 ± 0.01N • m (1.0 ± 0.1kgf • cm)
4 Solders
5 Screw
Boss
3 Zoom Gear Block
DSC-W150/W170_L2
2-8
2-4-2. Final Inspection (No Fault In Actual Motion/Actual Screen)
1 Zoom motion (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.
2 Zoom image
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.
3 Barrier (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
The barrier must be opened and closed fully, free from a sticking in the midway.
No abnormal sound must be heard during the operation.
4 Appearance condition
Scratches or stains must not be noticeable, except that the customer permits them.
5 Foreign matters on the lens
The lens condition must not be worse than that when the camera was received from the customer.
Upward
Lens at WIDE end
Upper oblique 45˚
Full stroke check
Horizontal
Lower oblique 45˚
Lens at TELE end
Downward
DSC-W150/W170_L2
2-9E
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
HELP 1: Window Adhesive Sheet Kit
HELP 2: LCD Radiation Sheet
Window Adhesive Sheet Kit must use only the
part of LCD window edge.
Please discard other parts.
Discard parts
Paste part
LCD Radiation Sheet
Window Adhesive Sheet Kit
HELP 3: Harness (HN-061/062/063/064)/Tape (N2/LS)
Harness (HN-061) (Yellow)
Harness (HN-064) (Blue) Harness (HN-063) (Pink)
Tape (N2)
Claw
AF Retainer
Harness (HN-062) (Gray)
Tape (LS)
DSC-W150/W170_L2
HELP
HELP 4: Harness (HN-063/064)/Capacitor Sheet
Harness (HN-064) (Blue)
Harness (HN-063) (Pink)
When connecting the harness to the strobe
capacitor terminals, wind the naked leads of
the harness around the terminals by more
than 1.5 turns, and then solder them.
Capacitor
Harness
Capacitor Sheet
Rib
Rib
DSC-W150/W170_L2
HELP
HELP 5: Sheets and Harness of ST-180 Board
HELP 6: BT Terminal Harness
BT Holder
- Top View -
BT902
(White)
BT903
(Black)
BT901
(Red)
SP Insulating Sheet
Harness (HN-062) (Gray)
Harness (HN-061) (Yellow)
ST-180 Board
Mic Harness (Orange)
Mic Harness (White)
- Bottom View ST-180 Board
Speaker Harness (Red)
Speaker Harness (Black)
Harness (HN-064)
(Blue)
SY-194 Board
Harness (HN-063)
(Pink)
BT Terminal Harness
BT900
ST Insulating Sheet
Mountain Fold
Valley Fold
BT Holder Mold
Valley Fold
SP Insulating Sheet
DSC-W150/W170_L2
HELP
HELP 7: Installation Method of Battery Terminal Board
1 Insert the battery terminal board into a slit in the BT holder to install.
* The battery terminal board is attached with the notch for installation.
BT holder
Notch
Battery terminal board
Battery terminal
board
2 Fold the notch 3 or 4 times repeatedly to break.
Notch
Battery terminal board
Notch
DSC-W150/W170_L2
HELP
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/2)
POWER BLOCK DIAGRAM (1/2)
OVERALL BLOCK DIAGRAM (2/2)
POWER BLOCK DIAGRAM (2/2)
DSC-W150/W170_L2
3. BLOCK DIAGRAMS
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
PWR_SAVE
PITCH
MOTOR
M
HALL
ELEMENT
28 - 35
36 - 38
2.7INCH
COLOR
LCD
XCS
XRESET
SI, SCLK
FP-866
ST-180
FLEXIBLE
BOARD (1/2) BOARD (1/2)
B6
E6
MIC_SIG
12
20
27, 26
CN701
(1/2)
E4
E5 AUDIO AMP
(7/10)
A5, A2
IC_203_AUOUT
SP±
CN002
(1/2)
MIC_SIG
MIC901
MICROPHONE
BLOCK
SP±
SP901
SPEAKER
Z_BOXPI-1_SENS_COL, Z_BOXPI-2_SENS_COL
32, 29
Z_BOXPI-1_GND, Z_BOXPI-2_GND
31, 34
50
THERM
ZM_DC_FG_1A,
ZM_DC_FG_1B
XZM_FG_LED
TZ_HALL_TEMP
15
YAW±
YAW_HALL_BIAS±,
YAW_HALL_±
PITCH±
PITCH_HALL_BIAS±,
PITCH_HALL±
A_OUT_L
38
Y18, Y17
W18, AB26, W17
T8
VIDEO_AMP_ON
IC602
4
3 VIDEO AMP 5
(7/10)
16
HD_Y
HD_Pb
HD_Pr
V_OUT
36
HD Y
HD Pb
HD Pr
34
7
9
20
24
4
2
USB_DP, USB_DM
2
Y10
M8
OVERALL (2/2)
(PAGE 3-2)
AD26
15, 17
Y1, AA1
AB23, AA23, AC25
IC_203_YOUT
AB13
IC_203_PBOUT
AF12
IC_203_PROUT
AC12
V_LINE_OUT
MSX_BS,
MSX_D0 - MSX_D3,
MSX_CLK
USB_VBUS
XMS_IN
USB_DP, USB_DM
USB_VBUS
13
6
CN703
MS_BS,
MS_D0 - MS_D3,
MS_CLK
6
2 - 5, 7, 8
ZM_SENS_1ST
AU_LINE_OUT
H11
A13 - A15,
B13 - B15
Z_PI_SENS_OUT
MC-191 FLEXIBLE
BOARD (1/2)
CN704
(1/2)
R8, AE25
MSHUT_DIR,
MSHUT_EN
FC_SENS
XFC_RST_LED
MEMORY
STICK
DUO
L8
AF3
SE501
J5
SWAOUT
13
21
YAW
SENSOR
1
PITCH
SENSOR
H10
U8
W13
IC506
CLK, DATA
24, 25
HALL
ELEMENT
ZM_DIR_A,
ZM_EN_A,
ZM_BRK_B
F_PI_SENS_OUT
47
FPI_GND
46
D5, D6
M
SHUTTER
MOTOR
DRIVER
D3, F1
SHUTTER_±
D5, A6, B6, C5
SHUTTER(±)
ZOOM
MOTOR
DRIVER
FC_DIR_A,
FC_DIR_B,
FC_EN_A
A2, C4, B2
ZOOM_A, ZOOM_A-
FOCUS
MOTOR
DRIVER
IRIS_M_DIR_2B,
IRIS_M_BRK_2B
G1, E4
Z_DC_MOTOR(±)
D2, B1
FOCUS_A, A, B, B
F_MOTOR_A, F_MOTOR_A(-),
F_MOTOR_B, F_MOTOR_B(-)
B7, C6, D6, E6
LV
SUB
SUB_CONT
IRIS MOTOR
DRIVER
B4, B5
26, 27
ND_±
IC503
OPTICAL
G5
IMAGE
STABILIZATION
DRIVE
C9
(3/10)
A7
A4, B4, B5
YAW
MOTOR
XLENS_DRIVER_PS
CN401
ND(±)
G6, J8, J9, J7 B10, D10
OIS TEMP
SENSOR
XCS_AUDIO
IC_203_AUIN
D1
IC401
VST1, VST2
VHLD1, VHLD2
J3, J2, H2, J4 B1, D1
OPTICAL IMAGE
STABILIZER
IC_203_2_SO,
XIC_203_2_SCK
IC603
AE8
LENS DRIVE D4
(2/10)
7, 8, 1, 2
ZOOM
FG
V8
AF8
Q302
10 - 13
ZOOM
RESET
SENSOR
AE23
AF22
Y11, W11
LH1
RG
SHUTTER
MOTOR
FOCUS
RESET
SENSOR
E10
D11
W170
3-6
M
CA_HD
CA_FD
H1 - H3
FOCUS
MOTOR
ZOOM
MOTOR
IC_203_2_SO, XIC_203_2_SCK
E11
VSUB_CONT_PRE,
VSUB_CONT_POST
16 - 19
M
XCS_FE, XIC_203_3_SCK, IC_203_3_SO
Q301
W170
M
CPU,
CAMERA DSP,
AV SIGNAL PROCESS,
LENS CONTROL,
GEAR_ON
Y13 MODE CONTROL
GEN_SYS_CLK
(4/10, 5/10)
Y12
41
42
F11
IRIS
MOTOR
M
1
CLOCK
3
GENERATOR
5
(8/10)
XCS_ PANEL
XDD_SYS_RST
U19
DCK, XHD, XVD
5, 6
G9, F9, J9, F6,
F7, G5, E9, D9,
F5, C4, E5, D10
V1A, V1B, V2,
V3A - V3C, V4,
V5A - V5C, V6S1,
V6S2, VOG
41 - 44
39, 40 20, 19
4
1
30
CCDOUT
2
LCD_CK, LCD_HD, LCD_VD
XDD_SYS_RST
V1, V2, V3A,
V3B, V4, V5A,
V5B, V6 - V10
37 - 40
36 - 38
IC001
10M CCD
IMAGER 35
24
V1A, V1B, V2,
V3A - V3C, V4,
V5A - V5C, V6S1,
V6S2, VOG
IC202
AF18
G9, G6, F9, J9,
F5 - F7, G5, E9,
E5, D9, C4, D10
16 - 20, 24 - 27, 30 - 33
3 - 14
6 - 10, 12 - 18, 3
CD-733 FLEXIBLE BOARD
X201
36MHz: W150
38MHz: W170
IC304
E6, E7 C5, B5
LV
21
SUB
13
SUB_CONT
43
V1, V2, V3A,
V3B, V4, V5A,
V5B, V6 - V10
GEN_TG_CLK
J5
CCD SIGNAL
PROCESS,
TIMING
GENERATOR
(1/10)
C8
G7
VHLD1, VHLD2
IC203
(1/2)
F3, E3
LV
SUB
SUB_CONT
W150
21
D1, D2, H1,
H2, K1, K2
4-6
23, 22 28, 29
VHLD1, VHLD2
L2
L4
22 - 25
30
1
24
VST1, VST2
D0 - D7
J8
H1 - H3
LH1
8
RG
10
VST1, VST2
LH1
RG
17 - 20, 24 - 27, 30 - 33
27 - 29
31, 32 16, 15
26
19
H1 - H3
CN705
LCD_D0 - LCD_D7
40, 39
IC001
8M CCD
IMAGER
CA_AD00 - CA_AD13
D17, B19, E17, A19,
E16, A18, D16, A17
BUFFER
(1/10)
1 16
L7
14
B18, D18, B17
IC309
10
E18, B23
CN301
CCDOUT
LCD901 (1/2)
LCD MODULE
V19, D19, C25
36
K9, L10, K10
CCDOUT
F4, F3
17
B6 - B10, C6,
C7, A8 - A3, B4
AB21, AC21, AB20, AC20, AB19,
AC19, AC18, AE21, AF21, AE20,
AF20, AE19, AF19, AE18
SY-194 BOARD (1/2)
W150
IRIS
(METER)
LENS
10, 12
LENS BLOCK
R7, AF25
3-1. OVERALL BLOCK DIAGRAM (1/2)
A3
A5
A6
SWBOUT
PITCH/YAW
SENSOR
AMP
(3/10)
10
CA_FD
XDD_SYS_RST
SE502
XDD_SYS_RST
IC_203_0_SO, IC_203_0_SI, XIC_203_0_SCK
CLK_IC_503
XCS_IC_503
XIC_203_IC_503_RST
05
DSC-W150/W170_L2
3-1
1
OVERALL (2/2)
(PAGE 3-2)
A : VIDEO SIGNAL
A : AUDIO SIGNAL
A : VIDEO/AUDIO SIGNAL
CN001
(1/2)
MULTI
CONNECTOR
3-2. OVERALL BLOCK DIAGRAM (2/2)
SY-194 BOARD (2/2)
MC-191 FLEXIBLE
BOARD (2/2)
ACV_UNREG
ST_UNREG
10, 9
FUNCTION
KEY
LCD901 (2/2)
LCD MODULE
S010
BACKLIGHT
BL_H
7, 6
MODE
DIAL
BL_L
3
KEY_AD1,
KEY_AD2
MODE_DIAL1,
MODE_DIAL2
BL_L
KEY_AD1,
KEY_AD2
1, 2
2
OVERALL (1/2)
(PAGE 3-1)
XMS_IN
K6
IC203
(2/2)
USB_VBUS
E7
XPWR_OFF
C10
BL_L
E10
XIC_203_RST_REQ
XDD_SYS_RST
D6
C9
XCS_DD
ST-180 BOARD (2/2)
CN002
(2/2)
S102
POWER
BT900
LITHIUM
BATTERY
XAF_LED
14
30
XPWR_ON
VL_3V
C4
C6 - C8
C5
FP-866
FLEXIBLE
BOARD (2/2)
K8
D10
MODE_DIAL1,
MODE_DIAL2
8
X001
32.768kHz
IC_203_0_SO,
IC_203_0_SI,
XIC_203_0_SCK
CN701
(2/2)
CPU,
CAMERA DSP,
AV SIGNAL PROCESS,
LENS CONTROL,
MODE CONTROL
(4/10, 5/10)
G8
XACC_IN
XAV_JACK_IN
IC_203_1_UI, IC_203_1_UO
UART_Rx, UART_Tx
BATT_UNREG
H5
F5
XCS_IC_201,
XIC_203_1_SCK,
IC_203_1_SO,
IC_203_1_SI
XDD_SYS_RST
E4
IC201
BATTERY
DETECTOR
(8/10)
B2
XAF_LED
3
1
OVERALL (1/2)
(PAGE 3-1)
XDD_SYS_RST
IC_203_0_SO, IC_203_0_SI, XIC_203_0_SCK
KEY_AD1, KEY_AD2
MODE_DIAL1,
MODE_DIAL2
S101
(SHUTTER)
13
15
D101
(AE/AF LOCK)
16
D102
FLASH CHARGE/
RECORD
17
D103
(POWER)
+
XE_H
18
XAE_LOCK_SW
XSHUT_SW
XAE_LOCK_LED
XSTRB_LED
XPWR_LED
XAE_LOCK_SW
XSHUT_SW
19
17
XAE_LOCK_LED
16
XSTRB_LED
15
XPWR_LED
14
AB7, AE6 AC8, AF6
29
N19
R19
W9
W8
Y9
T001
D001
3
2
4
1
H8
ST_UNREG
FLASH
UNIT
TRIGGER
TRIGGER_GND
XE_L
Q001
FLASH
DRIVE
15
IC001
1, 2
D701
C901
CHARGING
CAPACITOR
FLASH
CONTROL,
CHARGE
CONTROL
(1/2)
7
10
9
6
STRB_CHG
8
XSTRB_FULL
12
STRB_CHG_CONT
11
4
9
STRB_ON
STRB_CHG
XSTRB_FULL
STB_CHG_CNT
24
20
21
STRB_ON1
23
05
DSC-W150/W170_L2
3-2
17, 21
21 - 26
CHARGE_V
33
XACC_IN
UART Rx,
UART Tx
26
BATTERY
TERMINAL
A23
D004
XAF_LED
19
D002
XACV_IN
AF-113 BOARD
D201
SELF-TIMER/
SMILE SHUTTER/
AF ILLUMINATOR
XACV_DET
7
W12
AB18
18
2
G9
ACV_UNREG
15, 9
D7
D9
19, 12
XPWR_ON
XDIRECT_PB
D26, G19
S001 - S009,
S011
6
4, 5
5
XPWR_ON
XDIRECT_PB
W20, H18, B24, G18
CN702
XDIRECT_PB
20
XPOWER_ON
D001
BATT_UNREG
K7
CN001
S012
XACV_DET
Q001,
Q002
H17, A24, G17
SW-533
FLEXIBLE
BOARD
SW-529 BOARD
IC001
DC/DC
CONVERTER
(9/10)
B1, B5, C5, D5
MS_VCC
EVER
CAM_13V
CAM_3.5V
CAM_-7.5V
USB_3.2V
M_5V
D_3.1V
A_3.1V
DDR_1.8V
D_1.85V
D_1.5V
D_1.25V
BL_H
11
27 - 32
XPOWER_ON
XPWR_ON
23, 25
CN704(2/2)
V2
H9
H15
Y16
XACCESS_LED
D702
(ACCESS)
BATT_SIG
BT901
+
BT902
S
BT903
–
CN001
(2/2)
MULTI
CONNECTOR
3-3. POWER BLOCK DIAGRAM (1/2)
ACV_UNREG
SY-194 BOARD (1/2)
F001
CN704
27 - 32
23, 25
MC-191
FLEXIBLE
BOARD
F002
ACV_UNREG
IC001
DC/DC CONVERTER (9/10)
Q001, Q002
19
CN001
MULTI
CONNECTOR
XACV_DET
20
XACV_DET
G6 UNREG
D001
D002
CHARGE_V
21 - 26
17, 21
G3 MS_PWR_ON
BATT_UNREG
MS_VCC
MS_PWR_OUT F3
MS_PWR_IN F4
9
CN703
MEMORY
STICK
DUO
DDC5_PSW H1
L001
7
XPOWER_ON
11
DDC5_LX_1 J3
DDC5_LX_2 K3
XPOWER_ON
ST_UNREG
D006
XACV_IN
BATTERY
TERMINAL
G8 DDC12_PWR_IN1
G7 DDC12_PWR_IN2
IC201
BT901
BATTERY
DETECTOR
(8/10)
BATT_UNREG
+
BT902
S
BATT_SIG
P144_SOA0
P143_SIA0
P142_XSCKA0
P120_INTP0
E4 TXRX
BT903
–
D_3.1V
A
D
D5
C5
B5
B1
IC_203_1_SI
IC_203_1_SO
XIC_203_1_SCK
XCS_IC_201
DDC5_VO_1
DDC5_VO_2
LDO3P1U_IN
LDO3P1U_OUT
J2
K2
H4
J5
DDC12_PWR_OUT_1
DDC12_PWR_OUT_2
DDC12_LX_1
DDC12_LX_2
J8
K8
J9
K9
M_5V
B+ SWITCH
Q003
USB_3.2V
L002
CAM_13V
D007
POWER (2/2)
(PAGE 3-4)
DDC12_VFB H8
CAM_3.5V
LDO3P4_OUT H3
D008
H10 DDCM7P5_PWR
DDCM7P5_LX J10
DDCM7P5_VFB F8
C2 DDC2P9_PWR_1
B1 DDC2P9_PWR_2
DDC2P9_VO_1 F1
DDC2P9_VO_2 F2
DDC2P9_VFB G1
B2 XRESET
CAM_-7.5V
L006
D_3.1V
E
L008
XDD_SYS_RST
POWER (2/2)
(PAGE 3-4)
B3 DDC1P2_PWR
DDC1P2_LX A4
DDC1P2_VFB B2
B8 DDC1P8_PWR
DDC1P8_LX A8
DDC1P8_VFB B6
DDC1P8_PSW_IN B7
D_1.25V
L009
D_1.85V
D_1.5V
LDO1P5_OUT A6
DDR_1.8V
LDO1P8_OUT A7
EVER
LDO3P1E_OUT F5
B
POWER (2/2)
(PAGE 3-4)
MS_PWR_ON
IC_203_0_SI
IC_203_0_SO
XIC_203_0_SCK
XCS_DD
XIC_203_RST_REQ
XPWR_OFF
BATT_SENS
R008
MS_PWR_ON
R005
D004
RTCBAT H5
C7
C6
C8
C5
D6
C10
F6
R006
SO
SI
SCK
XCE
XRESET_REQ
XPWR_OFF
UNREG_MON
L004
VL_3V
F003
DDCBL_LX F10
D009
BL_H
DDCBL_VO F9
BL_L
DDCBL_VL E10
C
XPWR_ON
DIRECT_PB
D7 XPWR_ON1
D9 XPWR_ON3
POWER (2/2)
(PAGE 3-4)
A_3.1V
D_3.1V
XSYS_RESET C9
D_3.1V
XDD_SYS_RST
05
DSC-W150/W170_L2
3-3
XDD_SYS_RST
Q004
1.85V
DISCHARGE
POWER (2/2)
(PAGE 3-4)
3-4. POWER BLOCK DIAGRAM (2/2)
LCD901
LCD MODULE
SY-194 BOARD (2/2)
IC507
FB701
D_3.1V
L701
XRESET
XDD_SYS_RST
2.8V REG
(3/10)
PITCH/YAW
SENSOR AMP
(3/10)
Vout B1
B2 Vin
Vcont
A2
CN702
BL_H
10
BL_L
8
BL_H
BL_L
PITCH
SENSOR
D_1.85V
DIRECT_PB
IC503
XDD_SYS_RST
XIC_203_IC_503_RST
POWER (1/2)
(PAGE 3-3)
D_1.25V
CAM_13V
CAM_3.5V
CAM_-7.5V
SW-529 BOARD
BL_H
BL_L
BL_H
BL_L
1
3
XDIRECT_PB
6
BACKLIGHT
CN001
S012
5
YAW
SENSOR
C
POWER (1/2)
(PAGE 3-3)
CN701
XPWR_ON
A7 RESET_N
A6 XDL
D_3.1V
XDD_SYS_RST
FP-866
FLEXIBLE
BOARD
18
ST-180 BOARD
CN002
S102
POWER
14
D101
(AE/AF LOCK)
24, 25
D_1.5V
SW-533
FLEXIBLE
BOARD
SE501
OPTICAL
IMAGE
STABILIZATION
DRIVE
(3/10)
D_3.1V
M_5V
A
42
IC506
SE502
ST_UNREG
EVER
2.7INCH
COLOR
LCD
7, 8
A_3.1V
D_1.85V
CN705
VDDL(I)
22
VDDIO
21
VDD
20
AF-113 BOARD
D102
FLASH CHARGE/
RECORD
A_3.1V
D_3.1V
D_1.85V
D_3.1V
D_1.85V
D_3.1V
BL_H
BL_L
M_5V
A_3.1V
M_5V
A_3.1V
D201
SELF-TIMER/
SMILE SHUTTER/
AF ILLUMINATOR
D103
(POWER)
D_3.1V
T001
M_5V
IC603
POWER (1/2)
(PAGE 3-3)
AU_AVCC
4 VDD VOUT 1
ST_UNREG
ST_5V
M_5V
AUDIO AMP
(7/10)
1-3
Q701, Q702
ST_UNREG
29 - 31
E
22
10
D001
L001
FLASH
UNIT
STRB_UNREG_ON
3 CE
R601
H10 GPE_09
AB18 XRESET
IC601
2.8V REG
(7/10)
VIDEO AMP
(7/10)
D601
A_3.1V
D_1.85V
DDR_1.8V
IC001
FLASH CONTROL,
CHARGE CONTROL
(1/2)
IC602
R707
VL_3V
D702
(ACCESS)
R253
VL_3V
2
BT900
LITHIUM
BATTERY
VL_3V
30
W170
L241
VL_3V
D_3.1V
R254
D_1.25V
DDR_1.8V
D_1.85V
R205
D_1.85V
IC203
FB282
CPU,
CAMERA DSP,
AV SIGNAL PROCESS,
LENS CONTROL,
MODE CONTROL
(4/10 - 6/10)
FB283
IC202
CLOCK
GENERATOR
(8/10)
CAM_13V
L303
CAM_-7.5V
L302
FB302
XDD_SYS_RST
SIO0_RXD
SIO0_TXD
SID0_SCK
SIO0_SCS
XRESET_REQ
GPE_00
GPE_15
ADC0_IN6
D
POWER (1/2)
(PAGE 3-3)
IC_203_1_SI
IC_203_1_SO
XIC_203_1_SCK
XCS_IC_201
10M
CCD IMAGER
15
W150
IC309
BUFFER
(1/10)
CD-732 FLEXIBLE
BOARD
Q305
3.5V
DISCHARGE
D_1.85V
IC001
FB303
FB310
D_3.1V
2.3V REG
(1/10)
K8 GPE_05
G18
B24
H18
W20
IC001
8M
CCD IMAGER
IC304
IC306
XACV_IN
CAM_-7.5V
Q303
-7.5V
DISCHARGE
SIO1_RXD
SIO1_TXD
SIO1_SCK
GPS_04
XDD_SYS_RST
GPS_13 W7
GPE_03 J8
STRB_UNREG_ON
D_3.1V
M_5V
A_3.1V
XZM_RST_LED
05
DSC-W150/W170_L2
3-4E
CCD SIGNAL
PROCESS,
TIMING GENERATOR
(1/10)
1
CE
4 VDD VOUT 3
LENS BLOCK
Q401
SENSOR SWITCH
XZM_RST_LED
B
POWER (1/2)
(PAGE 3-3)
A24
H17
G17
A23
W12
G8
T7
AE7
CAM_13V
FB309
CAM_3.5V
EVER
IC_203_0_SI
IC_203_0_SO
XIC_203_0_SCK
XCS_DD
XIC_203_RST_REQ
XPWR_OFF
MS_PWR_ON
BATT_SENS
CD-733 FLEXIBLE
BOARD
CN301
40, 41
USB_3.2V
R402
R411
Z_BOXPI-1_SENS_Vcc
Z_BOXPI-2_SENS_Vcc
49
ZOOM
RESET
SENSOR
30
33
ZOOM
FG
48
FOCUS
RESET
SENSOR
R412
R401
E11 RSTB
CN401
Z_PI_SENS_Vcc
F_PI_SENS_Vcc
IC401
LENS DRIVE
(2/10)
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM
LENS BLOCK
W150
1
FP-866 FLEXIBLE BOARD
31
1
45
IC001
(Not supplied)
1
31
SW-529 BOARD
W170
BT900
LITHIUM BATTERY
BT902
+
S
2
Black
Red
SP901
SPEAKER
BT903
10
1
1
10
CN001
BT901
−
HARNESS (HN-069) (Black)
1
HARNESS (HN-067) (Red)
30
CN002
HARNESS (HN-068) (White)
31
1
SW-533 FLEXIBLE BOARD
1
BATTERY
TERMINAL
10
ST-180 BOARD (SIDE B)
45
IC001
(Not supplied)
FLASH UNIT
MIC901
MICROPHONE
BLOCK
LCD901
LCD MODULE
1
2
1
2
BACKLIGHT
1
CN301
C901
CHARGING CAPACITOR
2.7INCH
COLOR
LCD
10
30
ST-180 BOARD (SIDE A)
CN702
CN701
White
Orange
31
1
44
45
10
45
44
HARNESS (HN-064) (Blue)
CN705
CN401
51
50
2
1
IC203
(Not supplied)
12
11
LEVEL3
SY-194 BOARD
(SIDE B)
2
1
CN704
38
39
LEVEL3
SY-194 BOARD
(SIDE A)
LOCK
05
CN703
MEMORY STICK
CONNECTOR
HARNESS (HN-062) (Gray)
AF-113 BOARD
HARNESS (HN-061) (Yellow)
1
2
HARNESS (HN-063) (Pink)
CN001
MULTI CONNECTOR
1
26
28 25
2
39
1 27
MC-191 FLEXIBLE BOARD
DSC-W150/W170_L2
4-1
FRAME
4-2. SCHEMATIC DIAGRAMS
Link
CD-732 FLEXIBLE BOARD: W150
(CCD IMAGER)
SW-529 BOARD
(CONTROL SWITCH)
(CCD IMAGER)
(MULTI CONNECTOR)
ST-180 BOARD (1/2) (FLASH DRIVE)
(SY-ST CONNECTION)
ST-180 BOARD (2/2) (CONTROL SWITCH)
(SY-SW CONNECTION)
AF-113 BOARD (AF ILLUMINATOR)
COMMON NOTE FOR SCHEMATIC DIAGRAMS
DSC-W150/W170_L2
ENGLISH
JAPANESE
(ENGLISH)
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
(For schematic diagrams)
• All capacitors are in µF unless otherwise noted. pF : µ
µF. 50 V or less are not indicated except for electrolytics
and tantalums.
• Chip resistors are 1/10 W unless otherwise noted.
kΩ=1000 Ω, MΩ=1000 kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520
1. Connection
Pattern box
Color bar chart
For PTB-450:
J-6020-250-A
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
For PTB-1450:
J-6082-559-A
L = 24 cm (PTB-450)
L = 11 cm (PTB-1450)
Pattern box
Front of the lens
L
Kinds of capacitor
External dimensions (mm)
Case size
• Constants of resistors, capacitors, ICs and etc with XX
indicate that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with ★ differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic
curve B, unless otherwise noted.
• Signal name
XEDIT → EDIT
PB/XREC → PB/REC
• 2: non flammable resistor
• 5: fusible resistor
• C: panel designation
• A: B+ Line
• B: B– Line
• J : IN/OUT direction of (+,–) B LINE.
• C: adjustment for repair.
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the
measurement points and ground when camera shoots
color bar chart of pattern box. They are reference values
and reference waveforms.
(VOM of DC 10 MΩ input impedance is used)
• Voltage values change depending upon input
impedance of VOM used.)
Camera
A B
Red
Blue
White
Magenta
H
Cyan
Green
Yellow
2. Adjust the distance so that the output waveform of
Fig. a and the Fig. b can be obtain.
A=B
B A
Fig. a (Video output terminal output waveform)
Electronic beam
scanning frame
CRT picture frame
Fig.b (Picture on monitor TV)
Precautions for Replacement of Imager
• If the imager has been replaced, carry out all the adjustments
for the camera section.
• As the imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
When indicating parts by reference number, please
include the board name.
The components identified by mark 0 or dotted line with
mark 0 are critical for safety.
Les composants identifiés par une marque 0 sont
critiques pour la sécurité.
Ne les remplacer que par une pièce portant le numéro
spécifie.
DSC-W150/W170_L2
4-2
ENGLISH
JAPANESE
(JAPANESE)
回路図共通ノート
（他に必要なノートは各ブロックに記載してあります）
【回路図ノート】
1. 接続図
・ケミコン，タンタルを除くコンデンサで，耐圧50V以下のもの
はその耐圧を省略。単位はすべてμF（pはpF）。
・チップ抵抗で指示のないものは，1／10W以下。
kΩ＝1000Ω，MΩ＝1000kΩ
・チップ部品交換時の注意
取り外した部品は再使用せず，未使用の部品をご使用くださ
い。
タンタルコンデンサのマイナス側は熱に弱いため注意してくだ
さい。
・チップ部品には下記のように表示したものがあります。
例
C 541
L 452
22U
10UH
TA
A
2520
↑ ↑
↑
種類ケースサイズ
外形寸法（mm）
・抵抗，コンデンサ，ICなど定数にXXがあるものは，使用して
いない事を示しています。このため，使用していない回路が記
載されている事があります。
・★印のある部品は，機種などにより異なりますので機能別マウ
ント一覧表を参照してください。
・可変抵抗と半固定抵抗で，B特性の表示を省略。
・信号名表記について，下記のような場合があります。
XEDIT → EDIT PB/XREC → PB/REC
・2は不燃性抵抗。
・1はヒューズ抵抗。
・Cはパネル表示名称。
・AはB＋ライン。
・BはB−ライン。
・JはBライン（＋，−）の入出力方向を示す。
・Cは調整名称。
パターンボックス
カラーバーチャート
For PTB-450:
J-6020-250-A
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
For PTB-1450:
J-6082-559-A
L = 24 cm (PTB-450)
L = 11 cm (PTB-1450)
パターンボックス
レンズ前面
L
カメラ
2. 図a及び図bの波形が得られるように画枠調整して下さい。
H
シ
黄ア
ン
A B
マ
ゼ
白ン
ダ赤
緑
A=B
青
B A
図a（映像入出力端子出力波形）
【電圧・波形測定条件ノート】
・電圧値及び信号波形はパターンボックスのカラーバーチャート
を被写体としたときの測定点対アース間の参考値。
（デジタルマルチメータ；入力インピーダンス DC10MΩ使
用）
・使用テスタの入力インピーダンスにより電圧値が多少異なりま
す。
電子ビーム走査線
ブラウン管の画像枠
イメージャ交換時の注意
図b（テレビモニタの映像）
・イメージャを交換した場合は，カメラ部の全調整を
行ってください。
・イメージャは構造上，静電気により破壊される恐れが
あるため，MOS ICと同様に注意して取り扱ってくだ
さい。
また，受光部にはゴミの付着，および強い光がはいる
ことのないように注意してください。
0印の部品，または0印付きの点線で囲まれた部品は，
安全性を維持するために重要な部品です。
従って交換時は，必ず指定の部品を使用して下さい。
お願い
図面番号で部品を指定するときは基板名又はブロック
を併せて指定して下さい。
DSC-W150/W170_L2
4-3
VST2
Note: IC001 (CCD imager) and CD-732 flexible complete board are
not supplied,but there are included in CCD block assy(S).
CN301
Page 4-6
of Level 3
C
D
E
F
CD_GND
SUB_CONT
LND042
CD_GND
LND041
CAM_13V
LND040
CAM_13V
LND039
CD_GND
LND038
CD_GND
LND037
CD_GND
LND036
CCDOUT
LND035
CD_GND
LND034
CD_GND
LND033
V8
LND032
V6
LND031
V10
LND030
V9
LND029
VST2
V1
V2
V5A
V4
V3B
V3A
V2
V1
VL
SUB
V7
LV
IC001
ICX636EQP-H
8M CCD IMAGER
V8
V9
H3
H2
V10
H1
VST2
LH1
VST1
DGND
SUB_CONT
VHLD2
VHLD1
LV
B
17 18 19 20 21 22 23 24
C
C009
0.22u
16V
C010
0.1u
16V
V8
V6
V10
V9
VST2
LND028
VST1
LND027
V5B
LND026
V5A
LND025
V4
LND024
V7
LND023
VHLD1
LND022
VHLD2
LND021
LV
LND020
V3B
LND019
V3A
LND018
V1
LND017
V2
LND016
NC
LND015
CAM_-7.5V
LND014
CD_GND
LND013
SUB
LND012
CD_GND
LND011
CD_GND
LND010
RG
LND009
CD_GND
LND008
LH1
LND007
CD_GND
LND006
H2
LND005
H1
LND004
H3
LND003
CD_GND
LND002
CD_GND
LND001
VHLD1
CSUB
LND044
LND043
VHLD2
V6
VOUT
CD_GND
1
V5B
Note: Voltages of IC001 can not be measured,
because this is mounted by the side of the lens.
45P
LND045
VST1
2
25 26 27 28 29 30 31 32
SY-194
(1/10)
3
SUB_CONT
V10
4
CSUB
V9
5
GND
V8
6
VSS
V7
7
AGND
V6
8
9
V5B
A
C005
0.1u
10V
B
16 15 14 13 12 11 10
A
B
8
7
V3A
6
RG
5
V4
4
V3B
3
VDD
2
V5A
1
VST1
V5B
D
V5A
V4
V7
VHLD1
VHLD2
LV
V3B
V3A
V1
V2
E
SUB
RG
LH1
H2
H1
H3
CD-732 FLEXIBLE BOARD : W150
CCD IMAGER
CD_GND
F
1P
05
DSC-W150/W170_L2
4-4
CD-732
8
V1B
V3A
V1A
7
V2
6
V3B
5
V3C
4
V4
3
V5A
2
V5B
1
LND040
CAM_13V
LND039
CD_GND
LND038
CD_GND
LND037
CD_GND
LND036
CCDOUT
LND035
F
05
V3A
V2
V1B
V1A
28
29
30
31
32
33
5
V3B
27
2
1
VHLD2
VHLD1
H2
H1
RG
26
4
NC
H3
NC(VDD2)
NC
3
V3C
VHLD1
VDD
40
V4
VHLD2
VOUT
39
SUB
38
V5A
IC001
ICX665SQP-13
10M CCD IMAGER
B
C
34
35
CD_GND
LND033
V6S2
LND032
V6S1
LND031
VOG
LND030
V5C
V6S2
V6S1
VOG
C005
0.1u
16V
C006
0.22u
16V
C008
0.1u
10V
V5C
VST2
LND029
E
VL
VST2
VST1
VOG
CD_GND
LND034
D
VOG
V6S2
LV
37
CAM_13V
LV
V6S1
36
CD_GND
LND041
VGND
V5C
LH1
LND042
6
NC
SUB_CONT
7
NC(GND)
LND043
24
CD_GND
25
CD_GND
LND044
8
AGND
C
LND045
23
45P
9
NC
22
Page 4-6
of Level 3
10
NC
17
21
CN301
11
SUB_CONT
VST1
12
CSUB
VST2
SY-194
(1/10)
13
HGND
V6S2
14
AGND
Note: Voltages of IC001 can not be measured,
because this is mounted by the side of the lens.
18
B
V6S1
19
Note: IC001 (CCD imager) and CD-733 flexible complete board are
not supplied,but there are included in CCD block assy(S).
20
V5C
15
V5B
A
16
A
VST2
LND028
VST1
LND027
V5B
LND026
V5A
LND025
V4
LND024
V3C
LND023
VHLD1
LND022
VHLD2
LND021
LV
LND020
V3B
LND019
V3A
LND018
V1A
LND017
V2
LND016
V1B
LND015
CAM_-7.5V
LND014
CD_GND
LND013
SUB
LND012
CD_GND
LND011
CD_GND
LND010
RG
LND009
CD_GND
LND008
LH1
LND007
CD_GND
LND006
H3
LND005
H2
LND004
H1
LND003
CD_GND
LND002
CD_GND
LND001
CD_GND
VST1
D
V5B
V5A
V4
V3C
VHLD1
VHLD2
LV
V3B
V3A
V1A
V2
V1B
E
RG
LH1
H3
H2
CD-733 FLEXIBLE BOARD : W170
H1
F
CCD IMAGER
1P
DSC-W150/W170_L2
4-5
CD-733
Schematic diagrams of the SY-194 board are not shown.
Pages from 4-6 to 4-15 are not shown.
DSC-W150/W170_L2
• Refer to page 4-2 (English), 4-3 (Japanese) for mark 0.
1
2
3
4
5
6
8
7
AF-113
LND201, LND202
Through the
Harness
(HN-61, HN-62)
LND033
XAF_LED
A
D_3.1V
31P
6
REG_GND
7
STRB_CHG
8
STRB_ON
9
10
STRB_CHG_CONT
11
XSTRB_FULL
12
C901
315V
87uF
CHARGING
CAPACITOR
3.8
17 16 15 14 13
XSHUT_SW
15
XSHUT_SW
XAE_LOCK_LED
16
XAE_LOCK_LED
XSTRB_LED
17
XSTRB_LED
XPWR_LED
18
XPWR_LED
REG_GND
19
3.8
REG_GND
22
REG_GND
23
5
0
R006 XX
C003
XX
D_3.1V
24
D_3.1V
25
D_3.1V
SP-
26
SP-
SP+
27
REG_GND
28
XAF_LED
29
VL_3V
30
SW
VCC
F_ON
C001
1u B
CL001
VL_3V
6
7
5
SP+
REG_GND1
IC001
TPS65552RGTR
FLASH CONTROL,
CHARGE CONTROL
0
CHG
XFULL
B
FLASH
UNIT
TRIGGER_GND
XE_L
LND036
LND039
C005
0
TRIGGER_GND
250V
0.033u
3.1
C
Q001
CY25BAJ-8F
FLASH
DRIVE
8
5
1
6
2
7
3
8
4
0
C004
XX
FP-866
FLEXIBLE
LND031
TRIGGER
-
CL002
31
R003
1M
LND037
N.C
MIC_GND
PGND
G_IGBT
21
PGND
SW
N.C
REG_GND(MIC_GND)
2
MIC_SIG
3
20
1
REG_GND1
MIC_SIG
LND035
XE_H
LND032
N.C
XPWR_ON
N.C
XAE_LOCK_SW
14
VBATT
13
XPWR_ON
N.C
XAE_LOCK_SW
NC
D
T001
HGND
ST_5V
+
4
1
I_PEAK
C
REG_GND
LND038
CRF02(TE85R)
4
B
5
D001
C006
220p
50V B
D003
RB520S-40TE61
REG_GND
C002
22u C
6.3V
(Pink)
4
3
HARNESS (HN-063)
NC
2
R005
4700
(Blue)
3
HARNESS (HN-064)
2
ST_UNREG
A
Page 4-17
of Level 2
LND034
L001
2.2uH
10 11 12
1
ST_UNREG
9
ST_UNREG
C008
4.7u
B
6.3V
CN002
R001
1M
270
0
R002
47
D
LND041-LND071
Page 4-19
of Level 2
Note: C901, harness (HN-063) and harness (HN-064)
are not included in ST-180 complete board.
E
E
ST-180 BOARD (1/2)
FLASH DRIVE
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
F
F
05
DSC-W150/W170_L2
4-16
ST-180 (1/2)
1
2
3
4
1
4
3
2
Note: LCD901 is not included in
SW-529 complete board.
LCD901(2/2)
LCD MODULE
A
LND001
BL_H
A
BL_L
XSTRB_LED
BACKLIGHT
D102
LNJ426W830S0
XPWR_LED
S003
(POWER)
(ZOOM)
W
1
T
3
4
LND107
S008
2
1
2
D_3.1V
3
4
BT900
VL_3V
LITHIUM
BATTERY
2
1
S001
MENU
S102
POWER
1
2
4
N
3
4
2
2
3
3
1
MIC_GND
MIC_SIG
MIC_SIG
C
MIC901
MICROPHONE
BLOCK
C
S004
S007
b
z
2
4
3
LND011-LND020
Page 4-19
of Level 2
3
4
3
4
3
15
SP901
SPEAKER
1
LND104
3
16
2
1
S005
1
V
3
2
(SELF-TIMER)
4
2
S002
HOME
D
D
D
17
18
ST-180 BOARD (2/2)
B
LND003
D001
XX
STATIC_GND
C
S010
Note: BT900 (lithium battery), MIC901 and
SP901 are not included in ST-180 complete board.
CN001
1
4
SP+
BL_H
B
1
LND103
SP+
NC
1
S009
2
4
SP-
BL_L
2
(FLASH)
(MACRO)
2
1
LND101
SP-
NC
3
1
1
3
5
7
LND102
MIC_GND
XDIRECT_PB
4
2
3
(2nd)
SHIFT_ON
4
XSHUT_SW
C
MODE_DIAL2
5
(DISP)
1
(1st)
MODE_DIAL1
6
S012
v
3
S101
(SHUTTER)
XAE_LOCK_SW
REG_GND
7
SW-533
FLEXIBLE
RB002
2200
2
4
6
8
4
KEY_AD2
8
11
4
3
(SLIDESHOW)
S006
XPWR_ON
9
VDR001 XX
2
B
2
B
REG_GND1
1
REG_GND1
1
S011
LND106
B
KEY_AD1
(FLASH CHARGE/RECORD)
D103
CL-196SYG-CD-T
VL_3V
A
10
LND002
RB001
2200
1
3
5
7
A
(AE/AF LOCK)
12
D101
CL-196SYG-CD-T
2
4
6
8
XAE_LOCK_LED
(MODE DIAL)
AUTO
3
EASY
4
EASY
5
HIGH SENS
6
SOFTSNAP
7
SMILE
8
LANDSCAP
9
TWILIGHT PORTRATI
10
TWILIGHT PORTRATI
11
SCENE SELECTION
12
MOVIE
13
PROGRAM AUTO
14
1
3
5
7
RB004
2200
2
4
6
8
RB003
2200
2
4
6
8
1
3
5
7
D
Note: S010 (Mode dial) is not supplied,
but this is included in SW-529 complete board.
CONTROL SWITCH
05
1
2
3
4
E
A
ST-180
(1/2)
A
LND033, LND034
LND201
XAF_LED
Through the
Harness
(HN-061, HN-062)
LND202
D_3.1V
Page 4-16
of Level 2
E
4
3
2
5
1
6
CL-360S-TD4-X-TL
D201
SELF-TIMER/
SMILE SHUTTER/
AF ILLUMINATOR
F
SW-529 BOARD
CONTROL SWITCH
F
XX MARK:NO MOUNT
B
B
AF-113 BOARD
05
AF ILLUMINATOR
05
DSC-W150/W170_L2
4-17
ST-180 (2/2), AF-113, SW-529
2
1
3
4
5
6
8
7
39P
LND001
REG_GND
LND003
A_GND
V_LINE_OUT
LND005
ACV_UNREG
LND009
ACV_UNREG
LND010
ACV_UNREG
LND011
ACV_UNREG
LND012
ACV_UNREG
LND013
ACV_UNREG
LND014
BATT_UNREG
LND015
BATT_UNREG
LND016
BATT_UNREG
LND017
BATT_UNREG
LND018
BATT_UNREG
LND019
BATT_UNREG
LND020
XACV_DET
LND021
UART_Rx
LND022
USB_GND
LND023
USB_DM
LND024
HD Pr
ACV_GND
1
HD Pb
ACV_GND
3
USB_VBUS
ACV_GND
USB_GND
XPOWER_ON
USB_DP
UART Tx
9
A_OUT_L
UART Rx
A_GND
CHARGE_V
V_OUT
XACV_DET
25 23 21 19 17 15
LND027
USB_VBUS
LND028
UART_Tx
XPOWER_ON
LND030
REG_GND
LND031
HD_Pr
LND032
REG_GND
2
1
LF001
4
3
HD_Pb
LND034
REG_GND
LND035
ACV_GND
LND036
ACV_GND
LND037
ACV_GND
LND038
ACV_GND
LND039
ACV_GND
5
C
7
R004 1k
USB_GND
LND033
D
CN001
(MULTI CONNECTOR)
to AV/USB multi cable
USB_DP
LND026
LND029
Note: CN001 (multi connector) is not supplied, but this is included
in MC-191 flexible complete board.
N.C.
LND025
C
B
27
Page 4-15
of Level 3
LND008
USB_DM
USB_GND
V_GND
CHARGE_V
HD Y
ACV_UNREG
XACC_IN
ACV_UNREG
28
CN704
XACC_IN
2
SY-194
(10/10)
HD_Y
LND007
4
B
V_GND
LND006
6
LND004
A
AU_LINE_OUT
8
LND002
26 24 22 20 18 16 14 12 10
A
D
1P
LND044
STATIC_GND
E
E
F
MULTI CONNECTOR
F
05
DSC-W150/W170_L2
4-18
MC-191
1
2
3
4
1P
31P
A
SY-194
(10/10)
B
CN701
Page 4-15
of Level 3
C
LND031
ST_UNREG
ST_UNREG
LND041
LND030
ST_UNREG
ST_UNREG
LND042
LND029
ST_UNREG
ST_UNREG
LND043
LND028
NC
NC
LND044
LND027
REG_GND
REG_GND
LND045
LND026
REG_GND
REG_GND
LND046
LND025
REG_GND
REG_GND
LND047
LND024
STRB_CHG
STRB_CHG
LND048
LND023
STRB_ON
STRB_ON
LND049
LND022
ST_5V
ST_5V
LND050
LND021
STRB_CHG_CONT
STRB_CHG_CONT LND051
LND020
XSTRB_FULL
XSTRB_FULL
LND052
LND019
XAE_LOCK_SW
XAE_LOCK_SW
LND053
LND018
XPWR_ON
XPWR_ON
LND054
LND017
XSHUT_SW
XSHUT_SW
LND055
LND016
XAE_LOCK_LED
XAE_LOCK_LED
LND056
LND015
XSTRB_LED
XSTRB_LED
LND057
LND014
XPWR_LED
XPWR_LED
LND058
LND013
REG_GND
REG_GND
LND059
LND012
MIC_SIG
MIC_SIG
LND060
LND011
REG_GND(MIC_GND)
REG_GND(MIC_GND)
LND061
LND010
REG_GND
REG_GND
LND062
LND009
REG_GND
REG_GND
LND063
LND008
D_3.1V
D_3.1V
LND064
LND007
D_3.1V
D_3.1V
LND065
LND006
SP-
SP-
LND066
LND005
SP+
SP+
LND067
LND004
REG_GND
REG_GND
LND068
LND003
XAF_LED
XAF_LED
LND069
LND002
VL_3V
VL_3V
LND070
LND001
NC
NC
A
ST-180
(1/2)
B
CN002
Page 4-16
of Level 2
C
LND071
31P
1P
SY-ST CONNECTION
D
D
(PRINTED WIRING BOARD is omitted.)
05
1
2
3
4
1P
A
10P
LND001
KEY_AD1
KEY_AD1
LND020
LND002
KEY_AD2
KEY_AD2
LND019
LND003
REG_GND
REG_GND
LND018
SY-194
(10/10)
LND004
MODE_DIAL1
MODE_DIAL1
LND017
CN702
Page 4-15
of Level 3
LND005
MODE_DIAL2
MODE_DIAL2
LND016
LND006
XDIRECT_PB
XDIRECT_PB
LND015
LND007
NC
NC
LND014
LND008
BL_L
BL_L
LND013
LND009
NC
NC
LND012
LND010
BL_H
BL_H
10P
B
A
SW-529
CN001
Page 4-17
of Level 2
LND011
1P
B
SY-SW CONNECTION
(PRINTED WIRING BOARD is omitted.)
05
DSC-W150/W170_L2
4-19
FP-866, SW-533
4-3. PRINTED WIRING BOARDS
Link
AF-113 BOARD
SW-529 BOARD
ST-180 BOARD
COMMON NOTE FOR PRINTED WIRING BOARDS
DSC-W150/W170_L2
(ENGLISH)
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS
•
•
: Uses unleaded solder.
: Circuit board
: Flexible board
Pattern from the side which enables seeing.
: pattern of the rear side
(The other layers’ patterns are not indicated)
• Through hole is omitted.
• There are a few cases that the part printed on diagram
isn’t mounted in this model.
• C: panel designation
• Chip parts.
Transistor
B
(JAPANESE)
プリント図共通ノート
【プリント図ノート】
・
・
：無鉛半田を使用しています。
：基板
：フレキシブル配線板
見ている面側のパターン。
：裏側のパターン
（他のパターンについては表示されていません）
・スルーホールは省略。
・プリント図には，本機で使用していない部品が記載されている
場合があります。
・Cはパネル表示名称。
DSC-W150/W170_L2
4-20
Diode
6 5 4 4 5 6 5
C
E
4 4
3
5
3
3
1 23
1 2 3 3 2 1 1 2 3 3 2 1
2
1 2
1 2
1
4
3
3
4 6 5 4 4 5 6
2
1 1 2 3 3 2 1
2 2
1 3
2
5 4 3 3 4 5 4
1
1
2
3
2
4
1
1 6 54
CD-732 (2 layers), CD-733 (2 layers)
(W150)
LND001
LND002
LND003
LND004
LND005
LND006
LND007
LND008
LND009
LND010
LND011
LND012
LND013
LND014
LND015
LND016
LND017
LND018
LND019
LND020
LND021
LND022
LND023
LND024
LND025
LND026
LND027
LND028
LND029
LND030
LND031
LND032
LND033
LND034
LND035
LND036
LND037
LND038
LND039
LND040
LND041
LND042
LND043
LND044
LND045
(W170)
1
1
LND001
LND002
LND003
LND004
LND005
LND006
LND007
LND008
LND009
LND010
LND011
LND012
LND013
LND014
LND015
LND016
LND017
LND018
LND019
LND020
LND021
LND022
LND023
LND024
LND025
LND026
LND027
LND028
LND029
LND030
LND031
LND032
LND033
LND034
LND035
LND036
LND037
LND038
LND039
LND040
LND041
LND042
LND043
LND044
LND045
237-DC
< IP>
337-DC
<IP>
45
45
12
15
5
4
1
20
C005
C010
IC001
C005
C008
IC001
29
21
5
C006
C009
13
6
16
25
28
26
36
35
05
05
Note: IC001 (CCD imager) and CD-732 flexible complete board 1-874-980are not supplied, but there are included in CCD block assy(S).
1
40
1-874-981Note: IC001 (CCD imager) and CD-733 flexible complete board
are not supplied, but there are included in CCD block assy(S).
11
DSC-W150/W170_L2
4-21
11
CD-732, CD-733
Printed wiring board of the SY-194 board is not shown.
Page from 4-22 is not shown.
DSC-W150/W170_L2
ST-180 (4 layers), AF-113 (2 layers)
MIC901
MICROPHONE
BLOCK
ST-180 BOARD (SIDE A)
2
D003
R005
13
16
1
1
2
IC001
17
4
C008
C006
12
D103
(POWER)
<WG PE>
311-FA
11-
4
D201
3
D201
SELF-TIMER/
SMILE SHUTTER/
AF ILLUMINATOR
9
8
5
L001
C005
R001
8
CL002
C001
R003
C003
C002
C004
R006
5
D101
(AE/AF LOCK)
AF-113 BOARD
6
4
LND034 LND033
05
1
Q001
D101
LND038
HARNESS (HN-063) (Pink)
1
R002
4
LND037
+
C901
CHARGING
CAPACITOR
S101
S102
LND102
HARNESS (HN-064) (Blue)
(SHUTTER)
1
3
LND101
4
Orange
White
POWER
3
1-874-411-
21
Note: Harness (HN-061) and harness (HN-062) are not included
in AF-113 complete board and ST-180 complete board.
B
Y
LND202
CAUTION
G
LND201
05
1-875-220-
11
21
注意
Note: BT900 (lithium battery), C901, MIC901, SP901, harness (HN-063)
and harness (HN-064) are not included in ST-180 complete board.
BT900
BATTERY,
LITHIUM SECONDARY
ST-180 BOARD (SIDE B)
D102
FLASH CHARGE/
RECORD
D102
LND107
CL001
LND106
LND031 LND032
31
30
1
CN002
2
Red
Black
LND103 LND104
1
2
T001
LND039
4
LND036
3
LND035
05
K
D001
A
1-874-411SP901
SPEAKER
TRIGGER
21
TRIGGER_GND
XE_L
XE_H
FLASH UNIT
DSC-W150/W170_L2
4-23
ST-180, AF-113
SW-529 (2 layers)
SW-529 BOARD (SIDE A)
3
S003
1
S008
4
2
2
4
W
SW-529 BOARD (SIDE B)
1
3
T
(ZOOM)
BL-H
4
16
S001
1
11
CN001
12
2
1
RB003
8
7
1
D001
MENU
3
Note: S010 (Mode dial) is not supplied, but this is
included in SW-529 complete board.
VDR001
7
5
3
2
15
6
7
1
RB004
8
2
3 14 2 13 12 11
10
9
8
1
7
8
RB001
1
2
18
S010
(MODE DIAL)
LND002
10
BL-L
1
LND001
17
TO LCD901
(BACKLIGHT)
HOME
v
(DISP)
4
S002
3
2
4
1
2
4
2
3
S006
7
RB002
b
(MACRO)
1
2
8
1
2
S007
1
2
3
4
LND003
2
4
S004
B
(FLASH)
z
S009
1
3
4
1
3
V
(SELF-TIMER)
1
S005
3
N
2
4
3
1
S012
1
4
2
(SLIDESHOW)
2
S011
3
4
1-875-219-
11
21
05
05
DSC-W150/W170_L2
4-24
1-875-219-
11
21
SW-529
MC-191 (2 layers)
1
Note: CN001 (multi connector) is not supplied,
but this is included in MC-191 flexible complete board.
26
28
CN001
25
39
2
1
27
MC-191
>PI<
LND044
LND038LND039
LND037
LND036
LND035
LND034
LND033
LND032
LND031
LND030
LND029
LND028
LND027
LND026
LND025
LND024
LND023
LND022
LND021
LND020
LND019
LND018
LND017
LND016
LND015
LND014
LND013
LND012
LND011
LND010
LND009
LND008
LND007
LND006
LND005
LND004
LND003
LND002
LND001
R004
LF001
3
4
1
2
1-874-982-
11
05
DSC-W150/W170_L2
4-25E
MC-191
NOTE
5. REPAIR PARTS LIST
NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
EXPLODED VIEWS
Link
A
B
CABINET SECTION
C
MAIN FRAME SECTION
E
D
CABINET (UPPER) SECTION
BT HOLDER SECTION
Link
LENS SECTION
ELECTRICAL PARTS LIST
AF-113 BOARD
E
C
MC-191 FLEXIBLE BOARD D
DSC-W150/W170_L2
C
ACCESSORIES
ST-180 BOARD
E
SW-529 BOARD
B
Ver. 1.1 2008.05
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from
the original one.
• Items marked “*” are not stocked since they are seldom required for routine
service. Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not
supplied.
• Due to standardization, replacements in the parts list may be different from
the parts specified in the diagrams or the components used on the set.
• CAPACITORS:
uF: µF
• COILS
uH: µH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
When indicating parts by reference number,
please include the board name.
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
• Color Indication of Appearance Parts
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
(JAPANESE)
【使用上の注意】
• ここに記載されている部品は, 補修用部品であるため, 回路図及び
セットに付いている部品と異なる場合があります。
• -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合
があります。
• *印の部品は常備在庫しておりません。
• コンデンサの単位でuFはμFを示します。
• 抵抗の単位Ωは省略してあります。
金被：金属被膜抵抗。
サンキン：酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμ
A..., μPA..., μPB..., μPC..., μPD...を示します。
•
Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
EE : East European model
HK : Hong Kong model
J
: Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
TH : Thai model
TW : Taiwan model
DSC-W150/W170_L2
5-1
お願い
図面番号で部品を指定するときは基板名又はブロック
を併せて指定してください。
0印の部品，または0印付の点線で囲まれた部品は，
安全性を維持するために，重要な部品です。
従って交換時は，
必ず指定の部品を使用してください。
• 外装部品色表示
例：
(SILVER):セットの色を表す。
(Silver) : 部品の色を表す。
DISASSEMBLY
5-1. EXPLODED VIEWS
HARDWARE LIST
5-1-1. CABINET SECTION
ns: not supplied
6
#20
ns
3
#20
5
4
#20
(Note)
#20
2
1
#3
Main Frame Section
(See page 5-3)
#20
#20
Note: L C D 窓接着紙K I T を交換する際は，「H E L P 1 :
Window Adhesive Sheet Kit」を参照してくださ
Note: Refer to “HELP 1: Window Adhesive Sheet Kit”
when replace the LCD window adhesive sheet kit.
Ref. No.
Part No.
Description
1
1
1
1
1
X-2189-939-1
X-2189-940-1
X-2189-941-1
X-2189-942-1
X-2189-943-1
CABINET (FRONT) ASSY (W170: SILVER)
CABINET (FRONT) ASSY (W170: BLACK)
CABINET (FRONT) ASSY (W170: RED)
CABINET (FRONT) ASSY (W170: GOLD)
CABINET (FRONT) ASSY (W150: SILVER)
1
1
1
2
3
X-2189-944-1
X-2189-945-1
X-2189-946-1
3-300-527-01
3-300-528-01
CABINET (FRONT) ASSY (W150: BLACK)
CABINET (FRONT) ASSY (W150: RED)
CABINET (FRONT) ASSY (W150: GOLD)
CABINET (R), SIDE
CABINET (L), SIDE
4
X-2189-955-1 CABINET (REAR) ASSY (W170: SILVER)
Ref. No.
DSC-W150/W170_L2
5-2
Part No.
Description
4
4
4
4
X-2189-956-1
X-2189-957-1
X-2189-958-1
X-2189-959-1
CABINET (REAR) ASSY (W170: BLACK)
CABINET (REAR) ASSY (W170: RED)
CABINET (REAR) ASSY (W170: GOLD)
CABINET (REAR) ASSY (W150: SILVER)
4
4
4
5
6
X-2189-960-1
X-2189-961-1
X-2189-962-1
3-300-548-01
3-300-536-01
CABINET (REAR) ASSY (W150: BLACK)
CABINET (REAR) ASSY (W150: RED)
CABINET (REAR) ASSY (W150: GOLD)
SHEET KIT, WINDOW ADHESIVE (Note)
WINDOW, LCD
#3
#20
2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
2-635-591-31 SCREW (M1.4), NEW TRUSTAR P2 (Silver)
DISASSEMBLY
HARDWARE LIST
60
58
57
56
55
LCD901
54
53
#20
52
51
BT Holder Section
(See page 5-5)
59
#20
Lens Section
(See page 5-4)
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
51
* 52
53
* 54
55
3-300-532-01
3-298-230-11
3-300-529-01
3-093-800-01
1-875-540-11
SCREW, TRIPOD
TAPE (N2)
FRAME, MAIN
GASKET (230)
58
59
* 60
LCD901
3-289-762-01
3-083-884-01
3-300-526-01
1-802-585-11
DIAL, MODE
TAPE (LS)
SHEET, LCD RADIATION
LCD MODULE (LS027A3DC01)
56
* 57
A-1528-434-A SW-529 BOARD, COMPLETE
3-289-767-01 SHEET, ZOOM BLIND
#20
DSC-W150/W170_L2
5-3
2-635-591-31 SCREW (M1.4), NEW TRUSTAR P2 (Silver)
HARDWARE LIST
5-1-3. LENS SECTION
ns: not supplied
106
(including IC001 (CCD imager) and
CD-732/733 flexible complete board)
(Note 4)
107
W170
#115
101
ns
105
(Note 2)
#136
(Note 3)
103
(Note 1)
102
104
(Note 1)
(Note 2)
Note 1: Refer to “2-3. Barrier Assy Replacing Method” on
page 2-6 when replace the barrier assy.
Note 3: Tightening torque = 0.098 ± 0.01 N•m (1.0 ± 0.1
kgf•cm)
Note 1: バリア組立を交換する際は，2 - 6 ページの「2 - 3 .
Barrier Assy Replacing Method」を参照してくだ
さい。
Note 3: 締め付けトルク＝0 . 0 9 8 ± 0 . 0 1 N • m （1 . 0 ± 0 . 1
kgf•cm）
Note 4: Be sure to read “Precuations for Replacement of
Imager” on page 4-2.
Note 2: Refer to “2-4. Zoom Motor Replacing Method” on
page 2-8 when replace the zoom gear block.
Note 4: イメージャの交換時は，4-3ページの「イメージャ
交換時の注意」を必ずお読みください。
Note 2: ズームギアブロックを交換する際は，2 - 8 ページ
の「2-4. Zoom Motor Replacing Method」を参照
してください。
Ref. No.
Part No.
Description
101
102
103
104
105
1-788-689-21
3-298-356-01
A-1526-403-A
3-298-355-01
1-480-766-11
OPTICAL UNIT (BE002)
RING (A), ORNAMENTAL (Note 1)
BARRIER ASSY (Note 1)
GEAR, NARUTO (Note 2)
GEAR BLOCK, ZOOM (BE002) (Note 2)
Ref. No.
106
A-1541-675-A CCD BLOCK ASSY (S) (including IC001
(CCD imager) and CD-733 flexible complete board)
(Note 4) (W170)
106
107
#115
#136
DSC-W150/W170_L2
5-4
Part No.
Description
A-1541-676-A CCD BLOCK ASSY (S) (including IC001
(CCD imager) and CD-732 flexible complete board)
(Note 4) (W150)
3-874-855-01 TAPE (CD) (W170)
3-348-998-51 SCREW (M1.4X3.5), TAPPING, PAN (Silver)
3-065-509-11 SCREW (M1.4), TAPPING (Black) (Note 3)
DISASSEMBLY
HARDWARE LIST
ns: not supplied
158
157
#3
ns
BT902
BT903 (Note)
(Note)
Cabinet (Upper) Section
(See page 5-6)
154 155
156
153
159
#20
BT901
(Note)
160
161
ns
162
151
#20
152
Note: Refer to “HELP 7: Installation method of battery terminal
board” when changing the battery terminal board.
Note: バッテリ端子板を交換する際は，「HELP 7: Installation
method of battery terminal board」を参照してください。
• Refer to page 5-1 for mark 0.
Ref. No.
Part No.
Description
Ref. No.
Part No.
151
151
151
151
* 152
X-2189-971-1
X-2189-972-1
X-2189-973-1
X-2189-974-1
3-288-271-01
HOLDER ASSY, BT (SILVER)
HOLDER ASSY, BT (BLACK)
HOLDER ASSY, BT (RED)
HOLDER ASSY, BT (GOLD)
LID, BT (SILVER)
0 157
* 158
159
1-875-250-11 FP-866 FLEXIBLE BOARD
3-298-230-11 TAPE (N2)
3-870-596-01 SHEET, SY RADIATION
* 152
* 152
* 152
153
0 154
3-288-271-11
3-288-271-41
3-288-271-51
3-300-550-01
1-965-766-11
LID, BT (BLACK)
LID, BT (RED)
LID, BT (GOLD)
LID, DC
HARNESS (HN-067) (Red)
160
160
161
162
0 BT901
A-1528-438-A
A-1528-440-A
A-1528-433-A
3-300-534-01
1-780-456-21
SY-194 BOARD, COMPLETE (SERVICE) (W170)
SY-194 BOARD, COMPLETE (SERVICE) (W150)
MC-191 FLEXIBLE BOARD, COMPLETE
PLATE, MULTI FIXED
TERMINAL BOARD, BATTERY (Note)
0 155
0 156
1-965-767-11 HARNESS (HN-068) (White)
1-965-768-11 HARNESS (HN-069) (Black)
0 BT902
0 BT903
#3
#20
1-780-456-21
1-780-456-21
2-660-401-01
2-635-591-31
SCREW (M1.7), NEW TRU-STAR, P2 (Red)
SCREW (M1.4), NEW TRUSTAR P2 (Silver)
DSC-W150/W170_L2
5-5
Description
HARDWARE LIST
5-1-5. CABINET (UPPER) SECTION
ns: not supplied
203
SP901
207
MIC901
204 205
(Note)
ns
206
202
(Note)
208
209
210
201
211
213
214
212
C901
#5
BT900
! : BT900
(LITHIUM RECHARGEABLE BATTERY)
Board on the mount position.
(See page 4-23)
CAUTION
Note: Refer to “HELP 4: Harness (HN-063/064)/Capacitor Sheet”
when replace harness (HN-063/064).
Note: ハーネス（HN-063/064）を交換する際は，「HELP 4: Harness (HN-063/064)/Capacitor Sheet」を参照してください。
注意
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
0 201
0*202
203
204
205
A-1528-432-A
1-480-482-11
X-2189-937-1
1-965-683-11
1-965-682-11
ST-180 BOARD, COMPLETE
FLASH UNIT
RELEASE ASSY
211
212
213
214
0 BT900
A-1528-435-A
3-300-530-01
3-300-643-01
3-300-642-01
1-756-710-12
AF-113 BOARD, COMPLETE
HOLDER, AF
SHEET, SP INSULATING
SHEET, ST INSULATING
LITHIUM RECHARGEABLE BATTERY
1-965-733-11
1-965-732-11
3-300-531-01
3-300-535-01
3-300-533-01
HARNESS (HN-064) (Blue) (Note)
HARNESS (HN-063) (Pink) (Note)
HOLDER, CAPACITOR
SHEET, CAPACITOR
RETAINER, AF
0 C901
MIC901
SP901
#5
1-114-592-11
1-542-721-21
1-826-403-61
3-080-204-01
ELECT
87uF
315V
MICROPHONE BLOCK
LOUDSPEAKER (1.0CM)
SCREW, TAPPING, P2 (Black)
206
207
208
209
210
DSC-W150/W170_L2
5-6
AF-113
CD-732
CD-733
MC-191
ST-180
5-2. ELECTRICAL PARTS LIST
Ref. No.
Part No.
Description
Ref. No.
A-1528-435-A AF-113 BOARD, COMPLETE
**********************
0
6-501-861-01 DIODE CL-360S-TD4-X-TL (SELF-TIMER/
SMILE SHUTTER/AF ILLUMINATOR)
Description
A-1528-432-A ST-180 BOARD, COMPLETE
**********************
(BT900 (lithium battery) is not included in ST-180 complete board.)
< DIODE >
* D201
Part No.
0*
1-480-482-11 FLASH UNIT
< BATTERY >
A-1541-676-A CCD BLOCK ASSY (S) (Note)
(Not supplied) CD-732 FLEXIBLE BOARD, COMPLETE (W150)
*******************************
(IC001 (CCD imager) and CD-732 flexible complete board are not supplied,
but there are included in CCD block assy(S).)
< CAPACITOR >
C005
C009
* C010
1-125-777-11 CERAMIC CHIP
0.1uF
0.22uF
0.1uF
10%
10%
10%
10V
16V
16V
1-756-710-12 LITHIUM RECHARGEABLE BATTERY
< CAPACITOR >
C001
C002
0*C005
C006
* C008
1-112-717-91
1-100-611-91
1-112-832-21
1-164-933-11
1-112-746-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
22uF
0.033uF
220PF
4.7uF
10%
20%
10%
10%
10%
6.3V
6.3V
250V
50V
6.3V
< CONNECTOR >
< IC >
IC001
0 BT900
* CN002
1-817-391-52 CONNECTOR, FPC (ZIF) 31P
(Not supplied) ICX636EQP-H (Note)
(IC001 is supplied including in the CCD block assy(S).)
A-1541-675-A CCD BLOCK ASSY (S) (Note)
(Not supplied) CD-733 FLEXIBLE BOARD, COMPLETE (W170)
*******************************
(IC001 (CCD imager) and CD-733 flexible complete board are not supplied,
but there are included in CCD block assy(S).)
< DIODE >
0 D001
D003
D101
* D102
D103
6-501-096-01
6-500-619-01
6-500-594-01
6-502-311-01
DIODE
DIODE
DIODE
DIODE
CRF02 (TE85R)
RB520S-40TE61
CL-196SYG-CD-T (AE/AF LOCK)
LNJ426W830S0
(FLASH CHARGE/RECORD)
6-500-594-01 DIODE CL-196SYG-CD-T (POWER)
< IC >
< CONNECTOR >
IC001
* C005
C006
C008
0.1uF
0.22uF
0.1uF
10%
10%
10%
6-707-555-01 IC TPS65552RGTR
16V
16V
10V
< COIL >
* L001
1-400-820-11 INDUCTOR
2.2uH
< IC >
< TRANSISTOR >
IC001
(Not supplied) ICX665SQP-13 (Note)
(IC001 is supplied including in the CCD block assy(S).)
0*Q001
6-551-676-01 TRANSISTOR
CY25BAJ-8F-T13-G12
< RESISTOR >
A-1528-433-A MC-191 FLEXIBLE BOARD, COMPLETE
*******************************
(CN001 (multi connector) is not supplied, but this is included in MC-191
flexible complete board.)
R001
R002
0 R003
R005
1-218-989-11
1-218-937-11
1-216-121-11
1-218-863-11
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
1M
47
1M
4.7K
5%
5%
5%
0.5%
1/16W
1/16W
1/10W
1/10W
< CONNECTOR >
CN001
(Not supplied) CONNECTOR, MULTIPLE (SOCKET)
(MULTI CONNECTOR)
(CN001 (multi connector) is supplied including in MC-191 flexible complete
board.)
< LINE FILTER >
LF001
1-457-223-11 COMMON MODE CHOKE COIL
CAUTION
注意
< RESISTOR >
R004
1-218-953-11 RES-CHIP
1K
5%
Note: Be sure to read “Precuations for Replacement of
Imager” on page 4-2.
1/16W
Note: イメージャの交換時は4-3ページの“イメージャ
交換時の注意”を必ずお読みください。
DSC-W150/W170_L2
5-7
ST-180
Ref. No.
Part No.
Description
Ref. No.
< SWITCH >
S101
S102
1-786-819-22 TACTILE SWITCH (SHUTTER)
1-771-844-21 SWITCH, TACTILE (SMD) (POWER)
< TRANSFORMER >
0 T001
1-445-108-21 TRANSFORMER, D.C-D.C CONVERTER
A-1528-434-A SW-529 BOARD, COMPLETE
***********************
(S010 (Mode dial) is not supplied, but this is included in SW-529 complete
board.)
< CONNECTOR >
* CN001
1-820-634-51 CONNECTOR, FPC (LIF (NON-ZIF))
< COMPOSITION CIRCUIT BLOCK >
RB001
RB002
RB003
RB004
1-234-376-11
1-234-376-11
1-234-376-11
1-234-376-11
RES, NETWORK
RES, NETWORK
RES, NETWORK
RES, NETWORK
2.2K (1005X4)
2.2K (1005X4)
2.2K (1005X4)
2.2K (1005X4)
< SWITCH >
*
*
*
*
*
S001
S002
S003
S004
S005
*
*
*
*
S006
S007
S008
S009
S010
* S011
* S012
1-786-914-31
1-786-914-31
1-786-914-31
1-786-914-31
1-786-914-31
SWITCH, TACTILE (MENU)
SWITCH, TACTILE (HOME)
SWITCH, TACTILE (W (ZOOM))
SWITCH, TACTILE (b (MACRO))
SWITCH, TACTILE (V (SELF-TIMER))
1-786-914-31 SWITCH, TACTILE (v (DISP))
1-786-914-31 SWITCH, TACTILE (z)
1-786-914-31 SWITCH, TACTILE (T (ZOOM))
1-786-914-31 SWITCH, TACTILE (B (FLASH))
(Not supplied) SWITCH, ROTARY (MODE DIAL)
(S010 (Mode dial) is supplied including in SW-529 complete board.)
1-786-914-31 SWITCH, TACTILE (SLIDESHOW)
1-786-914-31 SWITCH, TACTILE (N)
Electrical parts list of the SY-194 board is
not shown.
Page 5-9 to 5-12 are not shown.
DSC-W150/W170_L2
5-8
Part No.
Description
SW-529
Ver. 1.2 2009.06
Checking supplied accessories.
Note: This item is supplied with the unit as an accessory, but is
not prepared as a service part.
Cyber-shot Handbook (PDF)
Battery Charger
Battery Charger
BC-CSGB/BC-CSGC
BC-CSGB/BC-CSGC
0 1-480-175-11 (J)
0 1-480-175-31
0 1-480-175-21 (US, CND)
(EXCEPT US, CND, J)
Power Cord
0 1-555-074-91 (AUS)
0 1-783-952-61 (AR)
0 1-792-549-41 (JE)
0 1-824-910-71 (AEP, E)
0 1-832-121-31 (CH)
0 1-827-269-12 (UK, HK)
0 1-833-892-21 (KR)
0 1-835-434-11 (TH)
USB, A/V Cable for
Multi-use Terminal
1-834-813-11
Wrist Strap
2-050-981-01
CD-ROM
“Cyber-shot application software”
“Cyber-shot Handbook”
“Cyber-shot Step-up Guide”
3-294-892-01 (EXCEPT J)
3-294-893-01 (J)
Conversion (2P) Adaptor
Conversion (2P) Adaptor
0 1-569-008-12 (E: NTSC) 0 1-569-007-12 (JE)
(Note)
(Note)
Rechargeable Battery Pack
NP-BG1/Battery Case
0 A-1137-161-A (J)
0 A-1567-198-A (US, CND)
0 A-1641-431-A (EXCEPT US, CND, J)
The CD-ROM supplied contains all of language version of
the Cyber-shot Handbook (PDF) for printing.
・ The printed matter is not supplied. If required, please
order it with the part number below.
・ (Only for destination Japanese model)
日本国内については日本語のみが印刷での部品供給
可能です。
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
3-294-896-01
3-294-896-11
3-294-896-21
3-294-896-31
3-294-896-41
3-294-896-51
3-294-896-61
3-294-896-71
3-294-896-81
3-294-896-91
3-294-897-11
3-294-897-21
3-294-897-31
3-294-897-41
3-294-897-51
3-294-897-61
3-294-897-71
3-294-897-81
3-294-897-91
3-294-898-11
3-294-898-21
3-294-898-31
3-294-898-41
3-294-898-51
3-294-898-61
3-294-898-71
3-294-898-81
(JAPANESE)
(ENGLISH)
(FRENCH)
(ITALIAN)
(SPANISH)
(PORTUGUESE)
(GERMAN)
(DUTCH)
(TRADITIONAL CHINESE)
(SIMPLIFIED CHINESE)
(RUSSIAN)
(ARABIC)
(PERSIAN)
(KOREAN)
(POLISH)
(CZECH)
(HUNGARIAN)
(SLOVAK)
(SWEDISH)
(FINNISH)
(NORWEGIAN)
(DANISH)
(THAI)
(MALAY)
(TURKISH)
(GREEK)
(UKRAINIAN)
Instruction Manual
3-294-899-01 (JAPANESE) (J)
3-294-899-11 (ENGLISH) (CND, AEP, UK, E, HK, AUS, TH, JE)
3-294-899-21 (FRENCH, ITALIAN) (CND, AEP)
3-294-899-31 (SPANISH, PORTUGUESE) (AEP, E, AR, JE)
3-294-899-41 (GERMAN, DUTCH) (AEP)
3-294-899-51 (TRADITIONAL CHINESE, SIMPLIFIED CHINESE)
(E, HK, JE)
3-294-899-61 (RUSSIAN, UKRAINIAN) (AEP)
3-294-899-71 (ARABIC, PERSIAN) (E)
3-294-899-81 (KOREAN) (KR, JE)
3-294-899-91 (POLISH, CZECH) (AEP)
3-294-900-11 (HUNGARIAN, SLOVAK) (AEP)
3-294-900-21 (SWEDISH, FINNISH) (AEP)
3-294-900-31 (NORWEGIAN, DANISH) (AEP)
3-294-900-41 (THAI, MALAY) (E)
3-294-900-51 (TURKISH, GREEK) (AEP)
3-294-900-61 (ENGLISH, SPANISH) (US)
3-294-900-71 (SIMPLIFIED CHINESE) (CH)
3-294-900-81 (THAI) (TH)
DSC-W150/W170_L2
5-13E
DSC-W150/W170
LEVEL
2
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Argentine Model
Brazilian Model
Thai Model
Japanese Model
Tourist Model
SERVICE MANUAL
Ver. 1.2 2009.06
SUPPLEMENT-1
File this supplement with the service manual.
(09-049)
• Change of Repair Parts
• Revision of Accessories
Note: Please refer to Ver. 1.2 of SERVICE MANUAL (9-852-296-33) for the revision of accessories.
5-2. ELECTRICAL PARTS LIST
Page
Former
Ref. No.
Part No.
New
Description
Ref. No.
ST-180 Board
5-7
< DIODE >
D101
Description
< DIODE >
6-500-594-01 DIODE CL-196SYG-CD-T (AE/AF LOCK)
* D101
DSC-W150/W170_L2
9-852-296-81
Part No.
ST-180 Board
Sony EMCS Co.
6-502-336-01 DIODE LNJ326W831S0 (AE/AF LOCK)
2009F0500-1
© 2009.6
Published by Kohda TEC
HARDWARE LIST (1/7)
#1: M1.7 X 2.5
(Black)
2-635-562-11
#2: M1.7 X 4.0
(Black)
2-635-562-31
#3: M1.7 X 2.5
(Red)
2-660-401-01
1.7
2.5
1.7
4.0
#5: M1.7 X 3.5 (Tapping)
(Black)
3-080-204-01
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
1.7
1.7
4.0
#13: M1.7 X 2.5 (Tapping)
(Silver)
3-085-397-01
1.7
1.7
2.5
#16: M1.4 X 2.5
(Silver)
2-586-337-01
2.5
#19: M1.2 X 4.0 (Tapping)
(Red)
3-086-156-21
1.4
1.5
2.5
1.4
1.4
1.5
#18: M1.4 X 2.5
(Silver)
2-635-591-21
1.7 2.2
1.7
5.0
#15: M1.4 X 1.5
(Silver)
3-062-214-01
1.7
#17: M1.7 X 1.5
(Silver)
2-586-389-01
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
4.0
#14: M1.7 X 2.5
(Silver)
2-599-475-11
2.5
3.5
1.6
#10: M1.7 X 4.0
(Silver)
2-599-475-31
1.7
1.7
1.7
5.0
#8: M1.7 X 3.5 (Tapping)
(Silver)
3-078-890-01
1.4
3.5
1.4
2.5
#7: M1.7 X 1.6
(Black)
7-627-552-18
1.7
3.5
1.7
2.5
#6: M1.4 X 1.7
(Silver)
2-598-474-01
#9: M1.7 X 5.0 (Tapping)
(Silver)
3-078-890-21
#4: M1.4 X 2.5 (Tapping)
(Dark Silver)
3-348-998-81
#20: M1.4 X 3.0
(Silver)
2-635-591-31
1.4
1.2
4.0
3.0
HARDWARE LIST (2/7)
#21: M1.4 X 3.0
(Black)
2-662-396-21
#22: M1.7 X 5.0 (Tapping)
(Silver)
3-083-261-01
#23: M1.7 X 4.0 (Tapping)
(Black)
3-080-204-11
1.7
1.4
5.0
3.0
#25: M1.7 X 3.0
(Black)
2-635-562-21
3.0
3.0
#36: M3.0 X 6.0
(Silver)
4-886-821-11
3.0
4.0
6.0
6.0
#38: M3.0 X 20.0 (Tapping)
(Silver)
7-685-651-79
2.0
4.5
#35: M4.0 X 6.0 (Tapping)
(Silver)
3-975-291-02
8.0
#37: M2.0 X 6.0 (Tapping)
(Black)
3-080-206-31
3.0
4.0
#34: M3.0 X 8.0
(Black)
3-077-331-41
6.0
#32: M2.0 X 4.5 (Tapping)
(Silver)
2-102-498-01
1.2
3.5
#33: M3.0 X 6.0
(Silver)
3-077-331-21
4.0
#31: M3.0 X 4.0
(Silver)
2-102-434-01
1.4
1.4
1.4
2.0
#30: M1.2 X 3.5 (Tapping)
(White)
3-086-156-11
2.5
#28: M1.4 X 4.0 (Tapping)
(Silver)
3-348-998-61
1.4
2.0
#29: M1.4 X 2.5
(Black)
2-662-396-01
5.5
#27: M1.4 X 2.0
(Black)
2-662-396-11
1.7
1.7
1.7
4.0
#26: M1.4 X 2.0
(Silver)
2-635-591-11
3.0
#24: B1.7 X 5.5 (Tapping)
(Black)
4-679-805-11
#39: M2.6 X 5.0 (Tapping)
(Black)
7-685-791-09
#40: M2.0 X 4.0 (Tapping)
(Silver)
7-685-851-04
3.0
2.0
6.0
2.6
20.0
5.0
2.0
4.0
HARDWARE LIST (3/7)
#41: M3.0 X 8.0 (Tapping)
(Silver)
3-065-748-01
#42: M2.0 X 4.0 (Tapping)
(Silver)
7-628-253-00
#43: M1.7 X 4.0
(Red)
2-660-401-31
3.0
8.0
2.0
#46: M1.7 X 3.0
(Red)
2-660-401-11
1.7
3.0
#49: M2.0 X 4.0
(Black)
2-630-005-31
2.0
4.0
#48: M1.7 X 2.5
(Silver)
3-973-497-91
1.7
1.4
2.5
3.0
#50: M2.0 X 3.0
(Red)
2-891-494-11
1.7
3.0
#47: M1.4 X 3.0 (Tapping)
(Silver)
2-665-774-01
1.4
2.5
1.7
4.0
4.0
#45: M1.4 X 2.5
(Silver)
2-587-151-01
#44: M1.7 X 3.0 (Tapping)
(Silver)
3-078-890-61
#51: M2.0 X 2.5
(Silver)
3-073-686-01
#52: M2.0 X 4.0 (Tapping)
(Black)
3-080-206-11
2.0
2.0
2.0
4.0
3.0
2.5
#53: M2.0 X 5.0 (Tapping)
(Black)
3-080-206-21
6.0
5.0
#57: M1.7 X 4.0
(Black)
7-627-852-18
#56: M2.0 X 3.5
(Silver)
3-067-187-11
1.75
2.0
2.0
4.0
#58: M2.0 X 6.0 (Tapping)
(Silver)
3-719-408-11
6.0
2.0
3.5
#59: M2.0 X 5.0 (Tapping)
(Silver)
3-080-205-21
2.0
1.7
4.0
#55: M2.0 X 4.0
(Silver)
2-655-582-11
#54: M1.75 X 6.0 (Tapping)
(Black)
3-318-203-11
#60: M2.6 X 5.0
(Black)
3-061-062-11
2.6
2.0
5.0
5.0
HARDWARE LIST (4/7)
#61: M3.0 X 10.0
(Black)
7-682-549-09
#62: M2.0 X 3.0
(Silver)
3-080-202-21
3.0
10.0
2.0
12.5
#66: M1.4 X 1.4
(Silver)
2-635-591-41
1.4
3.5
2.0
4.0
3.5
3.5
#76: M1.7 X 4.0 (Tapping)
(Silver)
2-666-551-11
1.7
4.0
#79: M1.4X 2.0
(Silver)
2-587-151-11
#80: M1.4X 2.0
(Black)
3-279-411-01
1.4
1.4
1.2
2.0
1.7
1.7
#78: M1.4 X 3.5
(Red)
3-208-537-11
1.4
1.4
#75: M1.7 X 3.5 (Tapping)
(Silver)
2-666-551-01
6.0
#77: M1.2 X 5.0 (Tapping)
(Silver)
3-086-156-31
#72: M1.4 X 2.0
(Silver)
4-663-621-41
2.0
#74: M1.7 X 6.0 (Tapping)
(Silver)
2-666-551-31
1.7
4.0
#71: M1.4 X 2.0
(Red)
3-208-537-01
5.0
1.2
5.0
1.4
1.7
1.7
#73: M1.2 X 4.0 (Tapping)
(Black)
3-086-156-61
#68: M1.7 X 4.0
(Silver)
2-655-581-01
1.4
#70: M1.7 X 5.0
(Silver)
2-599-475-41
3.0
5.0
#67: M1.4 X 2.0
(Silver)
3-389-523-16
1.4
#69: M1.7 X 3.0
(Silver)
2-599-475-21
1.7
5.0
3.0
#65: M1.4 X 3.5
(Silver)
2-635-591-01
#64: M1.7 X 5.0 (Tapping)
(Silver)
2-666-551-21
#63: M5.0 X 12.5
(Black)
3-060-811-21
2.0
1.4
2.0
HARDWARE LIST (5/7)
#83: M1.7 X 7.0 (Tapping)
(Black)
3-080-204-41
#82: M1.4 X 1.4
(Silver)
3-272-251-01
#81: M1.7 X 2.5
(Silver)
2-515-756-01
1.4
1.7
2.5
2.5
#90: M1.7 X 3.0
(Silver)
3-271-395-01
#91: M1.7 X 3.0 (Tapping)
(Silver)
2-695-434-11
3.0
#97: M1.4 X 2.5
(Black)
2-662-396-31
1.4
1.4
3.0
2.5
#99: M2.5 X 6.0 (Tapping)
(Silver)
3-776-750-02
3.8
8.0
#96: M1.4 X 2.5
(Silver)
2-587-151-21
8.0
#98: M3.0 X 8.0
(Silver)
3-077-331-01
2.5
3.9
#95: M3.0 X 8.0 (Tapping)
(Black)
7-685-646-79
4.0
3.5
2.0
1.7
1.7
1.7
#92: M2.0 X 3.9
(Black)
3-268-954-01
3.5
#94: M1.7 X 4.0
(Black)
2-515-483-31
1.6
5.9
1.7
2.0
#93: M1.7 X 3.5 (Tapping)
(Silver)
3-254-082-01
1.6
5.3
4.0
5.0
#88: M1.6 X 5.9 (Tapping)
(Silver)
2-689-015-01
1.7
1.7
2.0
3.0
#87: M1.6 X 5.3
(Black)
2-689-328-01
#86: M1.7 X 4.0 (Tapping)
(Silver)
2-695-434-21
#89: M2.0 X 5.5 (Tapping)
(Silver)
2-695-575-01
1.7
7.0
1.4
#85: M1.7 X 2.5
(Black)
2-515-483-11
#84: M2.0 X 3.0
(Silver)
3-072-453-11
#100: M2.0 X 6.0
(Black)
3-080-203-51
2.5
6.0
2.0
6.0
HARDWARE LIST (6/7)
#102: M2.6 X 8.0
(Black)
7-621-284-30
#101: M2.0 X 5.0
(Silver)
7-621-555-39
2.6
2.0
5.0
#105: M2.0 X 4.0
(Red)
2-891-494-31
10.0
#106: M2.0 X 6.0
(Black)
3-713-786-11
#107: M2.0 X 5.0
(Silver)
3-032-750-01
2.0
4.0
6.0
#109: M1.7 X 3.0
(Black)
2-515-483-21
#110: M2.0 X 3.0
(Black)
2-630-005-21
5.0
#117: M1.7 X 4.5 (Tapping)
(Silver)
2-695-429-31
#115: M1.4 X 3.5 (Tapping)
(Silver)
3-348-998-51
1.4
#116: M2.0 X 3.5 (Tapping)
(Silver)
2-695-435-01
2.0
1.4
3.5
#119: M2.6 X 5.0
(Black)
7-627-556-58
1.4
2.0
#112: M1.4 X 5.0
(Black)
2-178-410-11
5.0
3.5
#118: M1.4 X 2.0
(Black)
2-655-580-01
1.7
3.0
4.0
5.5
1.7
1.7
2.0
1.7
#108: M1.7 X 3.0 (Tapping)
(Black)
2-695-430-01
#111: M1.7 X 4.0 (Tapping)
(Black)
2-887-124-01
#114: M2.0 X 5.5 (Tapping)
(Silver)
2-698-464-01
#113: M1.7 X 5.0
(Black)
2-635-562-41
8.0
5.0
3.0
3.0
3.0
2.0
2.0
1.7
#104: M3.0 X 8.0
(Black)
7-682-548-09
2.6
8.0
2.0
4.5
#103: M2.6 X 10.0
(Silver)
7-685-794-09
#120: M2.6 X 6.0
(Silver)
7-621-770-67
2.6
2.6
5.0
6.0
HARDWARE LIST (7/7)
#121: M2.0 X 4.0 (Tapping)
(Silver)
3-080-205-11
#122: M3.0 X 6.0
(Black)
7-682-547-09
#123: M4.0 X 8.0
(Black)
7-682-561-09
3.0
2.0
6.0
4.0
1.4
2.9 4.0
3.0
25.0
#130: M2.0 X 4.5 (Tapping)
(Silver)
3-732-817-11
3.0
12.0
#131: M4.0 X 12.0
(Silver)
3-452-471-01
3.0
4.0
2.6
6.0
#136: M1.4 X 4.0 (Tapping)
(Black)
3-065-509-11
#135: M2.0 X 2.5
(Black)
7-627-553-28
2.6
7.0
#132: M2.6 X 6.0
(Black)
4-673-655-01
12.0
#134: M2.6 X 7.0
(Black)
3-299-572-01
4.0
12.0
2.0
4.5
#133: M3.0 X 6.0
(Black)
3-452-484-01
6.0
#128: M4.0 X 12.0
(Black)
3-452-472-01
6.0
#129: M3.0 X 12.0
(Black)
7-682-550-09
1.7
2.0
#127: M3.0 X 25.0
(Black)
7-682-654-09
3.5
3.0
4.0
8.0
#126: M2.9 X 3.5
(Black)
3-292-616-01
#125: M1.4 X 3.0
(Black)
3-291-847-01
#124: M1.7 X 2.0
(Silver)
2-599-475-01
1.4
2.0
2.5
4.0
Reverse
985229633.pdf
Revision History
Date
1.0
2008.03
Official Release
1.1
2008.05
Revised-1
(A1 DI08-061)
• Addition of Thai Model
S.M. revised: Page 3, Page 5-1, Page 5-13
Yes
1.2
2009.06
Supplement-1
(S1 09-049)
• Change of Repair Parts
• Revision of Accessories
S.M. revised: Page 5-13
Yes
DSC-W150/W170_L2
History
Contents
S.M. Rev.
issued
—
Ver.
—

SERVICE MANUAL

Transcription

Similar documents

5. REPAIR PARTS LIST - [email protected]

SERVICE MANUAL

HDR-TG5/TG5E/TG5V/ TG5VE/TG7VE - EXIT EQUIPMENT

警告安全上のご注意

Silver Accessory ï¼ Sculpture Spring Collection 2015

HDR-SR1/SR1E - Panasonic Parts and Accessories

A-1 - Notebook Manuals

HS80M/HS50M

RX-V459/HTR-5940

SERVICE NOTES Issued by RJA

HDR-HC1/HC1E/HC1K/HC1EK - Philips Parts and Accessories

RX-V457/HTR-5840/DSP

RX-V757/DSP-AX757/DSP-AX757SE RX-V657/HTR-5860

PlantUML Language Reference Guide