cv7278 Softail Fairing Mount Installation Instructions

Softail Fairing Mount
CV7278
CV7278 Fits Softail Fairing Mount 00-10 FXST ONLY
Note: Inner, Outer Fairing and Radio Caddy must be purchased
separately.
ALL FIBERGLASS PARTS MUST BE PREFITTED BEFORE PAINTING.
CYCLE VISIONS IS NOT RESPONSIBLE FOR THE COST OF PAINTING.
Parts Included:
1-Bottom Support
1- Fairing Mount Plate
2- Side Plate (LH & RH)
2- Support Plates (Upper & Lower)
1-Cross over Bracket
1-5/16 Flat Washer
1-5/16-18 x Cap Screw
4-5/16-18 x 1” Chrome Button Head
9-5/16-18 Flange Nuts
1- 3/8-16 x 4 ½ Bolt
10-5/16-18 x 3/4” Button Head
1. Remove seat.
2. Remove gas tank bolts. Disconnect fuel line and slide gas tank back.
3. Remove headlight and any tins.
4. Remove clips and rubber trim. See Fig 1
5. Extend all turn signal and headlight wiring.
6. Install the left and right side plates through the triple trees and placing the top holes in the plate over
the studs on the frame. See Fig 2. it may be necessary to tap left and right side plates into place with a
hammer.
7. Install the top crossover bracket, (see Fig 3) and then install the top and bottom braces, leaving all
bolts loose at this time. See Fig 4
8. Move the gas tank forward and install new 3/8-16 x 4 ½ bolt in the bottom of gas tank
9. Install bottom support to frame. See Fig 6
10. Install inner fairing with radio caddy
11. Check fairing alignment making sure the fairing is level and square to the bike.
12. Tighten all bolts on the fairing.
13. Route all wires through the hole in the fairing mount plate. See Fig 7
14. Install turn signals, if using stock turn signals. If using Cycle Visions Illumabezel, connect
Illumabezel wiring harness to bike harness.
All Harley Davidson parts listed below are required for Fairing Mount kit installation, and must be
purchased separately:
Inner fairing (P/N 58735-98A)
Outer fairing (P/N 58733-98A)
Dual headlamp assembly (P/N 67775-01A)
Speaker grill LH (P/N 77022-98)
Speaker grill RH (P/N 77021-98)
Stud plate (2) (P/N 31733-98))
Radio caddy (P/N 77078-98)
Cover plate (2) (P/N 31735-98)
Acorn nut (4) (P/N 31589-80)
Well nut (5) (P/N 5207)
Washer (4) (P/N 6716
Screw (2) (P/N 2995)
Screw (10) (P/N 3732)
Windshield (P/N 57958-98)
Windshield trim (P/N 58705-98A
Windshield screws (5) (P/N 933
Windshield washers (5) (P/N 6054
Lamp plug (P/N 68705-93A)
DO NOT INSTALL THIS UNIT WITHOUT APPLYING LOCKTITE
TO EVERY SCREW, NUT OR BOLT!
Our Warranty Policy
Cycle Visions’ obligation under “Our Warranty Policy” is limited to one (1) year from date of purchase to repair or replacement of the defective item (s). Chrome, polished,
powder-coated, anodized finishes, or electrical parts are limited to thirty (30) day from date of purchase.
This warranty will be void on all products that show evidence of misapplication, improper installation, abuse, lack of proper maintenance, negligence, or alteration from their
original design.
The consumer will be responsible for removing from the vehicle any defective item (s), transportation costs prepaid and for reinstallation upon return by Cycle Visions. The loss
of use of the product, loss of time, inconvenience, commercial loss or consequential damages is not covered. Cycle Visions reserves the right to change the design of any
product without assuming any obligation to modify any product previously manufactured. Warranty returns of Cycle Visions products are few because of our high quality
products.
Carefully inspect all parts…. If you find that your parts arrived in damaged conditional all original packaging material (box and other materials) must be saved to make a proper
damage claim within seven (7) days. You must be able to present the damaged boxes and materials to the freight carrier to verify your claim. The user shall assume all legal,
personal, injury risk and liability and all other obligations, duties and risks associated therewith.
Cycle Visions 
San Diego, CA (619) 295-7800
www.cyclevisions.com
See our other products on the web!
Made in the USA
Rev 10/10
Fig 1
Fig 3
Fig 2
Fig 4
Fig 5
Fig 7
Fig 6