G E Appliance Cut Sheets

Transcription

GE Appliances
This brochure prepared for:
Southern Management - Encore Dev.
7694 Dorchester Blvd., Jessup,
Jessup, MD 20794
Date Created: 05/30/12
GE Appliances
Model#: GFWH1200DWW
GE® ENERGY STAR® 3.6 DOE Cu. Ft.
Capacity Frontload Washer
Model#: GFDN120EDWW
GE® 7.0 Cu. Ft. Super Capacity Electric Dryer
Approx Dimensions (HxDxW):
39 4/5 in X 32 in X 27 in
39 31/100 in X 32 187/1000 in X 27 in
• Stain Wash Cycle - Tackles the toughest stains, from fresh grass marks to food
spills
• HydroHeater™ internal water heater - Boosts water temperatures and helps
achieve sanitization
• eWash option - Energy-saving option uses a cold water wash on select cycles
without sacrificing performance
• ENERGY STAR® qualified and CEE Tier III rated - Meets or exceeds federal
guidelines for energy efficiency for year-round energy and money savings
• Vibration Control - Adjusts spin patterns for each floor type for a smoother wash
without walking or shaking
• 1100 RPM spin speed - Fast speeds remove more water during the spin cycle
to minimize drying time
• Speed Wash - Provides a quick wash for lightly soiled items that are needed in
a hurry
• DuraDrum™ interior - Provides long-lasting dependability
• HE SensorDry™ - With dual thermistors continually monitors moisture and
temperature to prevent clothing wear and tear due to over-drying and
inconsistent heat
• Speed Dry - Quickly dries items and small loads for families on the go
• eDry option - Energy-saving option reduces dry temperatures on select cycles
• 4 heat selections - Provide the right temperatures for your clothes-drying needs
• Delay start - Set the dryer to begin cycles whenever it’s convenient for you
Palisades of Arundel
GE Appliances
Model#: JSP42SNSS
Model#: JNM1541SMSS
GE® 30" Slide-In Electric Range with Self-Cleaning Oven
GE Spacemaker® Over-the-Range Microwave Oven
36 1/4 in X 27 1/2 in X 31 1/4 in
16 13/32 in X 15 1/4 in X 29 7/8 in
• Self-clean oven - Cleans the oven cavity without the need for scrubbing
• Electronic oven controls - Electronic touch pads are easy to operate
• 6"/9" PowerBoil™ element - Produces rapid, powerful heat
• 4.4 cu. ft. capacity - More room for cooking more dishes at once
• Ribbon heating elements - Consistent heat and glass surface provide fast, even
heating
• Ceramic-glass cooktop - Cleanup is quick and easy
• Frameless glass oven door - Simple, stylish and easy to clean
• 1.5 cu. ft. capacity - 950 watts (IEC-705 test procedure)
• Convenience Controls - Allow cooking and reheating at the touch of a button
• Auto and Time Defrost - Defrosting times and power levels are programmed
automatically or manually for optimal results
• Turntable On/Off - Ideal for oversized, oblong-shaped dishes
GE Appliances
Model#: JV536HSS
GE Profile™ 30" High Performance Range Hood
4 3/4 in X 20 in X 29 7/8 in
• Convertible venting - Offers vented or non-vented installation options
• Vertical and rear exhaust - Exhausts from the top or rear of the hood
GFWH1200D
GE® Energy Star® 3.6 DOE IEC Cu. Ft. Capacity Frontload Washer with Stainless Steel Basket
Dimensions and Installation Information (in inches)
Installation Information: For complete information, see
installation instructions packed with your washer.
Above illustration intended for dimensional reference only.
Refer to photography for actual product appearance.
For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
geappliances.com or call GE Answer Center®
service, 800.626.2000.
Listed by
Underwriters
Laboratories
Specification Created 1/12
360487
GFWH1200D
Special Installation Requirements:
Stacked Dimensions (in inches)
Stacked Installation:
•Brackets for stacking dryer over washer are not included with the washer.
Order part no. GEFLSTACK or part no. WE25X10018.
Alcove or Closet Installation:
•If your dryer is approved for installation in an alcove or closet, it will be
stated on a label on the dryer back.
•The dryer MUST be exhausted to the outside.
•Minimum clearances between dryer cabinet and adjacent walls or other
surfaces are: 0" either side, 3" front and rear
•Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52".
•Closet doors must be louvered or otherwise ventilated and must contain a
minimum of 60 sq. in. of open area equally distributed. If this closet contains
both a washer and a dryer, doors must contain a minimum of 120 sq. in. of
open area equally distributed.
•No other fuel-burning appliance shall be installed in the same closet with
a gas dryer.
Bathroom or Bedroom Installation:
•The dryer MUST be exhausted to the outdoors.
Pedestal Dimensions (in inches)
•The installation must conform with the local codes, or in the absence of
local codes, with the National Fuel Gas Code, ANSI Z223.
This optional 13" pedestal raises
the door opening and height of
the washer or dryer. Feet on 13"
pedestal allow it to adjust to
13-3/8" height.
Minimum Clearance other than Alcove or Closet Installations:
•Minimum clearances to combustible surfaces 0" both sides, 3" rear.
For more information on venting kits and accessories,
please call 1-800-GE-CARES.
SBSD137HWW - white
27
13
service, 800.626.2000.
28-3/4
Above illustrations intended for dimensional reference only.
Listed by
Underwriters
Laboratories
360487
GFWH1200D
Features and Benefits
• Stain Wash Cycle - Tackles the toughest stains, from fresh grass marks to food spills
• HydroHeater™ internal water heater - Boosts water temperatures and helps
achieve sanitization
• eWash option - Energy-saving option uses a cold water wash on select cycles without
sacrificing performance
• ENERGY STAR® qualified and CEE Tier III rated - Meets or exceeds federal guidelines for
energy efficiency for year-round energy and money savings
• Vibration Control - Adusts spin patterns for each floor typed for a smoother wash
without walking or shaking
• 1100 RPM spin speed - Fast speeds remove more water during the spin cycle to
minimize drying time
• Speed Wash - Provides a quick wash for lightly soiled items that are needed in a hurry
• Load-sensing adaptive fill - Washer automatically fills with just the right amount of
water for the load
• Model GFWH1200DWW – White on white
Modified Energy Factor (MEF)
2.20
Water Factor (WF)
4.0
360487
GFDN120ED
GE® 7.0 Cu. Ft. Super Capacity Frontload Electric Dryer
Electric Dryer Rating
240V
5600W, 24A, 60Hz
208V
4400W, 22A, 60Hz
Exhaust Options: 4-way via rear, right, left and bottom.
Circuit Requirements: An individual, properly grounded
branch circuit, protected by a 30-amp circuit breaker or
a time-delay fuse, is required.
Note: Dryer wall outlet must be located within 36”
of service cord entry and accessible when dryer is
mounted in position.
Installation Information: For complete information, see
installation instructions packed with your dryer.
service, 800.626.2000.
Listed by
Underwriters
Laboratories
360490
GFDN120ED
Special Installation Requirements:
Stacked Dimensions (in inches)
Stacked Installation:
•Brackets for stacking dryer over washer are not included with the dryer.
GEFLSTACK or part no. WE25X10018.
Alcove or Closet Installation:
•If your dryer is approved for installation in an alcove or closet, it will be
stated on a label on the dryer back.
•The dryer MUST be exhausted to the outside.
•Minimum clearances between dryer cabinet and adjacent walls or other
surfaces are: 0" either side, 3" front and rear.
•Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52".
•Closet doors must be louvered or otherwise ventilated and must contain a
minimum of 60 sq. in. of open area equally distributed. If this closet contains
both a washer and a dryer, doors must contain a minimum of 120 sq. in. of
open area equally distributed.
•No other fuel-burning appliance shall be installed in the same closet with
a gas dryer.
Bathroom or Bedroom Installation:
•The dryer MUST be exhausted to the outdoors.
Pedestal Dimensions (in inches)
•The installation must conform with the local codes, or in the absence of
local codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223
for gas dryers.
This optional 13" pedestal raises
the door opening and height of
the washer or dryer. Feet on 13"
pedestal allow it to adjust to
13-3/8" height.
Minimum Clearance other than Alcove or Closet Installations:
•Minimum clearances to combustible surfaces 0" both sides, 3" rear.
For more information on venting kits and accessories,
please call 1-800-GE-CARES.
service, 800.626.2000.
SBSD137HWW - white
27
13
28-3/4
Above illustrations intended for dimensional reference only.
Listed by
Underwriters
Laboratories
360490
GFDN120ED
Dryer Exhausting Information – Metal Duct Only
For complete information, see installation instructions packed with your dryer.
Ducting Materials: For best performance, this dryer should be vented with 4” diameter
all rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible
metal (semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may
be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct.
A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid
metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4” diameter can
be maintained throughout the entire length of the transition duct. Please see installation
instruction packed with your dryer for complete instructions when using flexible metal (foil
type) ducting.
Best performance
Maximum length of 4"
dia. rigid metal duct
Exhaust hood type
A
A
4
B
Domestic
dryer models
2-1/2
Exhaust Length Calculation:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the
side or bottom of dryer, add one turn.
2. The maximum length of 4’ rigid (aluminum or galvanized) duct which can be tolerated is
shown in the table.
A turn of 45° or less may be ignored. Two 45° turns within the duct length should be
treated as a 90° elbow.
7.0, 6.0 and 5.8 cu. ft.
capacity models
all electric dryers
Number
of
90°
turns
0
1
2
3
4
A
4"
opening
90 ft.
60 ft.
45 ft.
35 ft.
25 ft.
B
2-1/2"
opening
60 ft.
45 ft.
35 ft.
25 ft.
15 ft.
Above illustration intended for dimensional reference only.
A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed
house floor (crawl space), or into an attic, since the accumulated lint could create a fire
hazard or moisture could cause damage. Never terminate the exhaust into a common duct
or plenum with a kitchen exhaust, since the combination of lint and grease could create a
fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird
nesting, etc. The wall cap must also be located at least 12" above the ground or any other
obstruction with the opening pointed down.
For more information on venting kits and accessories, please call 1-800-GE-CARES.
2-1/2
3-1/2
1-3/4 Gas Pipe Electrical
12
Connection Connection
Listed by
Underwriters
Laboratories
360490
GFDN120ED
• DuraDrum™ - Provides long-lasting durability
• HE SensorDry Plus™ - Has dual sensors to monitor moisture levels
• Speed Dry - Quickly dries items and small loads for families on the go
• eDry option - Energy-saving option reduces dry temperatures on select cycles
• 4 heat selections - Provide the right temperatures for your clothes-drying needs
• Delay start - Set the dryer to begin cycles whenever it’s convenient for you
• Model GFDN120EDWW – White on white
360490
JSP42SN
GE 30" Slide-In Electric Range with Self-Cleaning Oven
®
Recommended
6" Min.
From Walls
30" Min.
Recommended
6" Min.
From Walls
Shave Raised Edge To Clear
Shave Raised Edge To Clear
31-1/8" Wide Control Panel31-1/8" Wide Control Panel
30"Models
Excluding
and JSP39Models JSS28 and JSP39
Min. JSS28Excluding
9/16
9/16
KW Rating
240V
11.6
208V
8.7
30" Min.
Note: Cabinets installed adjacent to slide-in ranges must have an adhesion spec
of at least 194° temperature rating.
Note: To reduce the possibility of scorching the side walls above the countertop
when no load is present on burners, it is recommended that a minimum 6"
spacing from adjacent side wall be allowed for possible extended high-heat
element operation.
Optional Kits For Slide-In
Electric Ranges
(Available At Additional Cost)
Accessory Backguards
(Attaches to the back of range
as a backguard when unit is
installed in 30" free-standing
cutout)
JXS32SS (Stainless) - 4" High
JXS32BB (Black) - 4" High
JXS37BB (Black) - 5-1/4" High
Body Sides
(Slide-in ranges are sold
without sides installed. Can
be installed on either left
or right when unit has one
exposed side [no cabinet
adjacent]. Kit contains
1 body side)
JXS77BB (Black)
35-7/8"–38"
from
floor to
2-1/2
countertop
13" Max.
15" Min.
25
2-1/2 7-1/2
7-1/2
Optional Lower Trim Kits
(If counter height is greater
than 36.5", a lower trim kit
is recommended to extend
the useful height to 38"
maximum)
JXS56BB – Black
2-1/2
30
Accessory
Backguard
2-7/8"
To Front
Surface Of
Countertop
If you are NOT using the
optional Filler or Backguard:
2-1/2
30
24
Rear Filler Strip
WB07T10680 - Black Filler Strip Assembly
31-1/4
30
31-1/4
If you are using the optional
20-5/8" Door
Filler or Backguard:
Clearance
From Front
Surface of
Countertop
25
30
If you are using the optional
Filler or Backguard:
30
A/B*
2-7/8"
To Front
Surface Of
Countertop
36-1/4
36-1/4
20-5/8" Door
Clearance
From Front
Surface of
Countertop
25-3/4**
30
Accessory
Backguard
A/B*
24
23-3/16
ge.com or call GE Answer Center® service,
If you are NOT using the
optional Filler or Backguard:
800.626.2000.
Acceptable
13" Max. Electrical
15" Min.
Outlet
Area
25
35-7/8"–38"
from floor to
countertop
Receptacle Locations: For all 30" Slide-In Ranges locally approved flexible service cord or conduit
must be used because terminals are not accessible after range installation. See shaded area
in drawing for location of electrical outlet box. Recommended outlet locations allow range to be
installed directly against rear wall.
30" Min.
Acceptable
Electrical
23-3/16
Outlet Area
23-3/16
(excluding handle)
*JXS37 is 5-1/4" and JXS32 is 4"
**Total depth from wall to
front of closed oven door
*JXS37 is 5-1/4" and J
including
handle is 27-13/16.
25-3/4**
(excluding handle)
depth from wall
Dimension and installation information are shown in **Total
inches.
front of closed oven d
including handle is 27
23-3/16
30
25
30
All GE ranges are equipped with
Listed by
If the countertop area is not flat, excess tension
may be
applied
to the glass cooktop causing breakage
an Anti-Tip
device.
The installation
Underwriters
and voiding the warranty. Make sure the wallofcovering,
flooring and cabinets around the range
this devicecountertop,
is an important,
can withstand the heat (up to 200°F) generated
by the
Laboratories
required
steprange.
in the installation
of the range.
A. Allow 30" minimum clearance between surface
units and bottom of unprotected wood or metal cabinet,
or allow a 24" minimum when bottom of wood or metal cabinet is protected by no less than 1/4"-thick
If the countertop area is not flat, excess tension may be applied to the glass cooktop causing breakage
flame-retardant millboard covered with no less than No. 28 MSG sheet metal (.015" thick), .015"-thick
and voiding the warranty. Make sure the wall covering, countertop, flooring and cabinets around the range
stainless steel, .025" aluminum or .020" copper.
can withstand the heat (up to 200°F) generated by the range.
B. This appliance has been approved for 0" spacing to adjacent surfaces above the cooktop. However,
Allow 30"
minimum
surface
unitscabinetry
and bottom
a minimum 6" spacing A.
to surfaces
less
than 15"clearance
above the between
cooktop and
adjacent
is of unprotected wood or metal cabinet,
or allow ato24"
minimum
bottom
of wood
or1/4"
metal
cabinet
is protected by no less than 1/4"-thick
recommended to reduce exposure
steam,
greasewhen
splatter
and heat.
Allow
minimum
clearance
flame-retardant millboard covered with no less than No. 28 MSG sheet metal (.015" thick), .015"-thick
at the back wall.
stainless steel, .025" aluminum or .020" copper.
To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space above
B. This
appliance
has been
for 0" spacing
to cooktop,
adjacentthe
surfaces
the cooktop should be avoided.
If cabinet
storage
spaceapproved
is to be provided
above the
risk canabove the cooktop. However,
Specification Revised 6/110
320646
JSP42SN
GE® 30" Slide-In Electric Range with Self-Cleaning Oven
• Self-Clean Oven - Conveniently cleans the oven cavity without need of scrubbing
• Electronic Controls - Provide a smooth easy-to-use, easy-to-clean surface
8
IH
6
4
8
8
6
4
2
LO
9
4
7
8
LO
LO
2
3
6
6
2
2
6
4
3
8
1
8
4
5
2
6
2
9
7
1
IH
• PowerBoil™ Element - Accommodates various-sized pots or pans and 3,000 watts of
power seeds the boiling process
4
5
• Extra-Large Oven Capacity - Enough room to cook an entire meal at once
• Ribbon Heating Elements - Provide powerful heat beneath a smooth glass surface
to ensure even heat and fast warm-up times
• Ceramic Glass Cooktop - A smooth cooktop surface makes cleaning quick and easy
• Two Oven Racks - Feature a durable construction to help accommodate any size or
type of cookware
• Certified Sabbath Mode - Prepared foods can stay warm in accordance with kosher law
• Big Hearth Window - Features an enhanced shape to add an elegant appearance
and make viewing trouble-free
• Frameless Glass Oven Door - Offers an easy-to-clean and stylish design that blends
seamlessly into existing cabinetry
• Model JSP42SNSS - Stainless steel
JSP42SN
320646
JNM1541SMSS
GE Spacemaker® 1.5 Cu. Ft. Over-the-Range Microwave
Oven Microwave Oven
Over-the-Range
Dimensions (in inches)
Note: Requires 120V grounded outlet. Electrical receptacle must be located in
cabinet above Spacemaker microwave oven. No additional wiring, venting or
cabinet rebuilding necessary in many cases. Complete detailed, easy-to-follow
installation instructions and convenient full-size templates are packed with the
Spacemaker microwave oven.
66" MIN.
Mounting
height
from
floor
Important Information: When installing the Spacemaker microwave oven over
a range, allow minimum of 2" from bottom of Spacemaker microwave oven to top
of range backguard to allow for removal of light covers.
Ventilation Options: The Spacemaker microwave ovens are designed for
adaptation to the following three types of ventilation:
• Outside exhaust (vertical – as shown)
• Outside exhaust (horizontal)
• Recirculating (non-vented ductless – see Filter Kit drawing)
Installation Information: This information is not intended to be used for installing
unit described. Before installing, consult installation instructions packed with
product/kit for current dimensional data.
30"
MIN.
width
required
Exhaust outlet
connects to
3-1/4" X 10" duct
13"
MAX.
12"
MIN.
15-1/4
24-1/2
105°
Door open
(without
obstruction)
16
16-13/32
(rear)
29-7/8
Minimum distance from
door hinge side to adjacent
wall should equal 1/2-inch.
800.626.2000.
Listed by
Underwriters
Laboratories
340132
JNM1541SMSS
GE Spacemaker® 1.5 Cu. Ft. Over-the-Range Microwave Oven
Optional Accessories (Available at additional cost)
Hood Exhaust Duct: Outside ventilation requires a HOOD EXHAUST DUCT. Read the
following carefully.
Exhaust Duct: The hood exhaust has been designed to mate with a standard
3-1/4" x 10" rectangular duct. If a round duct is required, a rectangular-to-round transition
adaptor must be used. Do not use less than a 6” diameter duct.
Rear Exhaust: If a rear or horizontal exhaust is to be used, care should be taken to
align exhaust with space between studs, or wall should be prepared at the time it is
constructed by leaving enough space between the wall studs to accommodate exhaust.
Maximum Duct Length: For satisfactory air movement, the total duct length of
3-1/4" x 10" rectangular or 6" diameter round duct should not exceed 120 equivalent feet.
Filler Panel kits
JX41
When replacing a 36"
range hood, this kit fills
in the additional width
to provide a custom
built-in appearance. For
installation between
cabinets only; not for
end-of-cabinet
installation. Each
kit contains two
3"-wide filler panels.
Filter kits JX81C–
Recirculating
Charcoal Filter kit
To be used when
the Spacemaker
microwave oven
cannot be vented
to the outside.
Elbows, Transitions, Wall and Roof Caps, etc., present additional resistance
to airflow and are equivalent to a section of straight duct which is longer than their
actual physical size. When calculating the total duct length, add the equivalent length of
all transitions and adaptors plus the lengths of all straight duct sections. The chart below
shows the approximate feet of equivalent length of some typical ducts.
Duct
A. Rectangular-To-round
Transition Adaptor
Equivalent Feet
5 ft.
B. Wall Cap
40 ft.
C. 90° Elbow
10 ft.
D. 45° Elbow
5 ft.
E. 90° Elbow
25 ft.
F. 45° Elbow
5 ft.
G. Roof Cap
24 ft.
800.626.2000.
Listed by
Underwriters
Laboratories
340132
JNM1541SMSS
GE Spacemaker® 1.5 Cu. Ft. Over-the-Range Microwave Oven
• 1.5 Cu. Ft. Capacity - 950 Watts (IEC-705 test procedure)
• Convenience Cooking Controls - Allows cooking and reheating
at the touch of a button
• Auto and Time Defrost - Automatically defrosts for a specified
amount of time
• Turntable On/Off - Ideal for oversized, oblong-shaped dishes
• Two-speed, 300-CFM Venting System- Quickly removes the
smoke and steam from the cooktop
• Removable Oven Rack - Makes multi-dish cooking possible
• 10 Power Levels - Offer maximum cooking flexibility, from
warming and reheating, to the full speed of microwave cooking
at high power
• Model JNM1541SMSS – Stainless Steel
convenience cooking
Beverage
Popcorn
Reheat
Potato
Time
Cook
1
Defrost
Auto/Time Reminder
Express Cook
4
6
Clear
Off
8
9
Delay
Start
0
Add
30 Sec.
DISPLAY
AM/PM
on/off
Start
Pause
5
7
Power
Level
Timer
3
2
Turn
Table
Surface
Light
Clock
Vent
Fan
SCROLL SPEED
JVM1540SMSS
JVM1540LMCS
JNM1541SMSS
800.626.2000.
Listed by
Underwriters
Laboratories
340132
TM
JV536H – GE Profile™ 30" Performance Range Hood
Dimensions (in inches)
D
12
9
1-1/4
4-3/4
A
5
1-9/16
1-1/2
B
12-9/16
C
Model
JV536
A
B
4-3/4 29-7/8
C
20
D
12
3/8
Exhaust outlet connects to 3-1/4" x 10" duct (vertically or horizontally) and 7" round
(vertically). Includes rectangular damper and 7" round damper adapter.
Round damper accessory, JXDA22 available at additional cost.
Amp Rating
120V
hood_a_b_c_new.eps
1.4
Installation Information: Before installing, consult installation
instructions packed with product for current dimensional data.
Light bulb(s) not included.
220970
JXHC1 Cord Kit – Allows a receptacle in the cabinet over the range to accommodate
either an over-the-range microwave oven or a standard hood.
JV666.eps
R
Listed by
Underwriters
Laboratories
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
TM
JV536H – GE Profile™ 30" Performance Range Hood
• Convertible venting – Hood configuration can be changed to fit the needs of various
installation requirements.
• Vertical and rear exhaust – Provides the option of connecting duct work to either the
rear or the top of the hood.
• Variable 2-speed fan control – Powerful variable speed exhaust system effectively pulls
smoke and vapors out of the kitchen.
• Halogen light – Provides bright light that illuminates the cooking surface below hood.
• Removable grease filter – Durable filters can be removed for easy cleaning
and maintenance.
JV536/566HSS
• Round and rectangular ducting – Hood is designed to fit either standard round
or rectangular duct work.
• Damper included.
• Model JV536HSS – Stainless Steel
• Model JV535HWW – White on white
• Model JV535HCC – Bisque on bisque
• Model JV535HBB – Black on black
220970

G E Appliance Cut Sheets

Transcription

Similar documents

residential venting application

Atlantis Energy Systems Inc.

Giggles and Good Times Pigeon Forge, Tennessee

Coffing EC3 Manual

Give the Gift of Art

Effective 01/10/11 Rev. 1 Kenmore Elite Front

VELTIA HAND DRYER Data Sheet

TECHNICAL DATA SHEET XLERATOR HAND

Mr. Jeffry Sifford 10:00 AM

Regions CD Check Viewer Installation Guide

Installation Instructions Gas Dryer