FJS/FJHS 1300 Data Sheet
Transcription
FJS/FJHS 1300 Data Sheet
Titan FJS/FJHS 1300 Titan Monitor Nozzle z Adjustable from straight jet to fog pattern z Self inducing foam venturi z Nominal flow 1,300 l/min @ 7 bar The Angus FJS 1300 bronze fog/jet nozzle is a simple and reliable design fitted with a rotating sleeve which allows the water or foam stream to be adjusted manually from straight jet to wide fog pattern. The outer sleeve is fitted with brass handles to allow easy adjustment when wearing gloves or operating under difficult conditions. THROW (m) 30.0 A foam inlet on the side of the nozzle is 25.0 NARROW FOG which can be set controlled by a valve 20.0 for 1%, 3%, 6% induction or closed (no 15.0 induction). 10.0 Water inlet connection 2½” BSP M, (NH thread optional) 3½” BSP F, (NH thread optional) 150 x 150 square flange with “O” ring seal Weights 2½” – 9.5 kg 3½” – 10.5 kg 150 x 150 flange – 11.0 kg Foam pick-up tube 25mm (1”) nominal diameter wire reinforced flexible PVC with chamfered dip tube - length 2m Hydraulic remote control The FJHS 1300 is fitted with a hydraulic cylinder for remote operation (with manual overide) K factor 490 (Flow l/min = K x √Pressure bar) Hydraulic connections ¼” BSP F Design pressure Maximum working pressure 16 bar Factory test pressure 24 bar 5.0 materials Nozzle 0.0 body to EN CC491K, equivalent Bronze 2 3 4 5 6 7 8 9 10 to LG2, Red Brass, ASTM B62 and UNI PRESSURE (bar) 7013-8 CopperZinc Lead FOG JET FULL JET Tin 85%5%5% 5% 60.0 40.0 THROW (m) Seals 30.0 Viton seals rated up to 120°C 20.0 10.0 194 31/2" BSP F. 50.0 Handles: brass STREAM STRAIGHT 2 3 4 5 6 7 PRESSURE (bar) 8 9 10 135 0.0 FLOW RATE (l/min) 1600 1400 1200 1000 800 3 4 5 6 7 PRESSURE (bar) 8 9 10 198 225 25.0 THROW (m) Titan FJS/FJHS 1300 15.0 10.0 5.0 0.0 Titan Monitor Nozzle 50.0 NARROW FOG 20.0 3 4 5 6 7 PRESSURE (bar) 8 9 10 15.0 10.0 5.0 2 3 140 4 5 6 7 PRESSURE (bar) 8 9 8 9 10 STRAIGHT STREAM 40.0 THROW (m) THROW (m) 25.0 30.0 20.0 10.0 0.0 10 2 3 4 5 6 7 PRESSURE (bar) 120 Length and height of nozzle jet Maximum water throw 42m* at an angle to the horizontal of 32°60.0 80 60 * Based on water at nozzle 50.0 inlet pressure of 7.0 bar and flow 1,300 l/min. STRAIGHT STREAM 20 3 40.0 Note: The jet throw depends on a number of variables such as wind direction, type 30.0 and concentration of foam in the water and the condition of the monitor 5 620.0 7 8 water 4 ways and nozzle. THROW (m) 40 Spread of Fog Spray 5 bar 30° fog jet 2.5m 60° fog jet 3.5m 9 1600 9 bar 2.3m 3.0m 1000 3 4 0.0 CROSS REFERENCE IN % BETWEEN JET HEIGHT AND LENGTH 2 3 4 5 6 7 PRESSURE (bar) Reaction Force kg 50 25 0 32 45 60 0 FLOW RATE (l/min) 1600 75 25 1400 50 LENGTH OF JET IN % 140 100% 1200 9 Solvent cleaning Primer coat Epoxy 30μm Intermediate coat Epoxy grey 40μm Finish coat Polyurethane 40μm Red RAL3000 5 6 7 PRESSURE (bar) 8 9 10 10 120 100 80 60 40 20 75 8 Surface preparation Total dry film thickness 110μm 800 10 10.0 (bar) Pressure 75% Optional Paint Finish 71400 bar 2.5m 1200 3.0m FLOW RATE (l/min) 100 HEIGHT OF JET IN % Reaction Force kg 2 60.0 30.0 0.0 NARROW FOG 20.0 3 4 5 6 7 8 9 10 Pressure (bar) For throw and height calculations at different angles refer to the chart above or the Angus Interactive 1000 Electronic Throw Program. 800 Monitors Fog/Jet Nozzles 3 4 5 6 7 8 9 10 The Angus monitor range includes Angus fog/jet nozzles cover the range PRESSURE (bar) bronze models up to 8,500 l/min and 200 to 20,000 l/min with self inducing stainless steel models up to 50,000 l/min. options up to 4,000 l/min. Cannons Angus foam cannons cover the range 800 to 15,000 l/min with a self inducing option and foam spreaders on all models. Most models are available with lever or gearbox control, automatic oscillation or with hydraulic or electric remote control. All are suitable for use where explosive atmospheres may be present. Angus is a company assessed to ISO 9001:2008. Monitors RHEMB 50 GMS 30 REMS 200 Specialist nozzles for dry powder are also available – refer to Angus. Fog/Jet Nozzles Cannons RHEMB 85 LMB 30 REMS 80 Most models are available with hydraulic or electric remote control options suitable for use in explosive rated areas. GMS 45 LMB 40 REMS 300 GMS 60 GMS 200 LMB 85 GMS 80 GMS 300 INTERNATIONAL SALES Angus Fire Ltd Angus House, Haddenham Business Park, Pegasus Way, Haddenham, Aylesbury, HP17 8LB, UK Tel: +44 (0)1844 293600 • Fax: +44 (0)1844 293664 UK SALES Angus Fire Ltd Station Road, Bentham, Lancaster, LA2 7NA, UK Tel: +44 (0)1524 264000 • Fax: +44 (0)1524 264180 Email: [email protected] • Web: www.angusfire.co.uk Angus Fire operates a continuous programme of product development. The right is therefore reserved to modify any specification without prior notice and Angus Fire should be contacted to ensure that the current issues of all technical data sheets are used. © Angus Fire 6454/3 02.14