User Manual CARFIT® Modular System Series CMK

Transcription

User Manual
CARFIT®
Modular System Series CMK
Table of contents
Contents CARFIT® Modular System CMK
Installation Instructions Using the Clamp
Assembly as an Example
1 Mounting support 1
7 Clamping a component
3
4
5
6
7
8
9
10
11
Legal information
These installation instructions are copyright. You are not
permitted to reproduce, translate, process using electronic
means, duplicate, distribute or publish this documentation
or any part of it without the prior express permission of
Carl Zeiss Fixture Systems GmbH. Infringers are liable for
damages. All rights reserved, especially rights arising from
by patents granted or the registration of a utility model.
We reserve the right to make changes to these installation
instructions. Carl Zeiss Fixture Systems GmbH provides no
warranties for these installation instructions, including any
implicit warranty for typical commercial quality or suitability
2
for any particular purpose. Carl Zeiss Fixture Systems GmbH
accepts no liability for any indirect, coincidental, or direct
damage of any kind, or loss of applications arising from
the use of these installation instructions. All product names
are registered trademarks or trademarks of their respective
owners.
Contents CARFIT® Modular System CMK
Kit Configuration
Part no.
Base Plate
240 x 240 x 15 mm
Picture
Kit Configuration
Part no.
13 05 1000
Adapter M4 x 15
13 05 1017
Support Bar 1
13 051001
Adapter M4 x 22,5
13 05 1018
Support Bar 2
13 05 1002
Adapter M4 x 30
13 05 1019
Assembly Clamping Clip
13 05 1003
Adapter M4 – M6
13 05 1020
Cramp Assembly
13 05 1004
Adapter M6 x 15
13 05 1021
Clipping Element
Assembly
13 05 1005
Adapter M6 x 22,5
13 05 1022
Connecting Element
Assembly
13 05 1007
Adapter M6 x 30
13 05 1023
Angle
13 05 1009
Adjustable Column
Assembly
13 05 1024
Column Support flat
13 05 1010
Column for Clip
L = 24
13 05 1026
Column Support with ball
13 05 1011
Column for Clip
L = 40
13 05 1027
Column Support with
cone 90°
13 05 1012
Assembly Column
13 05 1028
Column Support with
V-Block
13 05 1013
Lock Nut
13 05 1029
Column Support with
V-Block small
13 05 1014
Adapter M4
13 05 1034
Column Support with
V-Block
13 05 1015
Adapter M6
13 05 1035
Column Support 90°
13 05 1016
Adapter M6 long
13 05 1036
Picture
3
Installation Instructions Using the Clamp Assembly
as an example
4
1
Mounting support 1
Step 1
Step 4
Bolt adapter M4 x 30 (13 05 1019) onto base plate
(13 05 1000).
Bolt adapter M4 (13 05 1034) onto bracket (13 05 1009).
Step 2
Screw lock nut (13 05 1029) onto adapter M4
(13 05 1034).
Bolt adapter M4 x 15 (13 05 1017) onto adapter
M4 x 30 (13 05 1019).
Step 3
Bolt bracket (13 05 1009) onto adapter M4 x 15
(13 05 1017) using socket head screw (13 09 1010).
Step 5
Step 6
Bolt column support flat 90° (13 05 1016) onto adapter
M4 (13 05 1034) and secure with lock nut (13 05 1029).
5
2
Mounting support 2
Step 1
Step 4
(13 05 1000).
Bolt adapter M4 – M6 (13 05 1020) onto bracket
(13 05 1009).
Step 2
Step 5
Bolt adapter M4 x 30 (13 05 1019) onto adapter
M4 x 30 (13 05 1019).
Bolt column for clip (13 05 1027) onto adapter M4 – M6
(13 05 1020).
Step 3
6
3
Mounting support 3
Step 1
Step 4
Bolt support bar 1 (13 05 1001) onto base plate
Bolt column support flat with v-block (13 05 1015)
onto column (13 05 1028) and secure with lock nut
(13 05 1029).
Step 2
Screw column (13 05 1028) into the threaded hole on
support bar 1 (13 05 1001).
Step 3
Screw lock nut (13 05 1029) onto column (13 05 1028).
7
4
Mounting support 4
Step 1
Step 4
Bolt support bar 2 (13 05 1002) onto base plate
Screw connecting element assembly (13 05 1007) with set
screw (13 09 1012) into adapter M6 x 15 (13 05 1021).
Step 2
Step 5
Screw adapter M6 x 30 (13 05 1023) into the threaded
hole on support bar 2 (13 05 1002).
Screw column for Clip L = 40 (13 05 1027) into connecting
element assembly (13 05 1007).
Step 3
Step 6
Screw adapter M6 x 15 (13 05 1021) onto adapter
M6 x 30 (13 05 1023).
Tilt connecting element assembly (13 05 1007) and column
for clip L = 40 (13 05 1027) through 45° and secure in
place.
8
5
Mounting support 5
Step 1
Step 4
(13 05 1000).
Bolt adapter M4 (13 05 1034) onto bracket (13 05 1009).
Step 2
Screw lock nut (13 05 1029) onto adapter M4
(13 05 1034).
Connect two adapters M4 x 30 (13 05 1019) with one
another and screw onto adapter M4 x 30 (13 05 1019).
Step 3
Step 5
Step 6
Bolt column support flat (13 05 1010) onto adapter M4
(13 05 1034) and secure with lock nut (13 05 1029).
9
6
Mounting support 6
Step 1
Step 5
Bolt adapter M4 – M6 (13 05 1020) onto base plate
(13 05 1000).
Screw adapter M6 x 15 (13 05 1021) onto connecting
element assembly (13 05 1007).
Step 2
Step 6
Bolt adapter M6 x 30 (13 05 1023) onto adapter M4 – M6
(13 05 1020).
Screw column for clip (13 05 1026) onto adapter M6 x 15
(13 05 1021).
Step 3
Step 7
Screw adapter M6 x 30 (13 05 1023) onto adapter
M6 x 30 (13 05 1023).
Tilt connecting element assembly (13 05 1007) through
45° and fix in place.
Step 4
Screw connecting element assembly (13 05 1007) with set
screw M6 x 16 (13 09 112) into adapter M6 x 30
(13 05 1023).
10
7
Clamping a component
Step 1
Insert a component and push against stop (13 05 1006).
Step 2
Push the three clamping clips (13 05 1003) onto column
for clip (13 05 1026, 13 05 1027) and clamp the component tightly.
11
Carl Zeiss
Fixture Systems GmbH
Auf Rodert 6
66636 Tholey
Germany
Telefon: +49 (0) 68 53 50 12-0
Telefax: +49 (0) 68 53 50 12-31
E-Mail: [email protected]
www.zeiss.de/carfit
EN_68_070_001I Printed in Germany 03/2013
Subject to change in design and scope and result of ongoing technical development.
© conception, text and design: Carl Zeiss Fixture Systems GmbH

User Manual CARFIT® Modular System Series CMK

Transcription

Similar documents

Carfit Mats