HiPath 500 HiPath 3000 Gigaset SL1 professional Gigaset S1

Transcription

HiPath 500
HiPath 3000
Gigaset SL1 professional
Gigaset S1 professional
in HiPath Cordless Office
Operating Instructions
Safety notes
Safety notes
Handset
Danger:
• Do not use the handset in potentially explosive atmospheres.
• Do not install the handset in the vicinity of electronic equipment
to avoid mutual interference.
• Do not use the handset in wet rooms! Devices are not splashproof.
• A transmitter signal is emitted by your handset. Please observe
safety procedures for your area.
Note:
• Information for hearing aid users: Radio signals can interfere in
hearing aids.
• Please provide the operating instructions with the handset if
giving it to another user.
Note:
The ringing tone, signal tones and handsfree talking (speakerphone
mode) are played over the loudspeaker. Do not hold the telephone
to your ear when it is ringing or if speakerphone mode is switched
on. Otherwise you may seriously impair your hearing.
Note:
•
CE (customer equipment) does not continue to support emergency dialing after loss of mains power, if battery back up and
power fail swithover to emergency analogue phones is not available.
Batteries
Danger:
• Only use permitted batteries.
• Do not use conventional batteries. Failure to observe this advice
can lead to danger.
• Avoid contact with fire and water.
• Only use the approved C39280-Z4-C373 power supply unit to
operate the charging shell.
Safety notes
All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.
The correct disposal and separate collection of your old appliance will help prevent potential negative consequences for the
environment and human health. It is a precondition for reuse
and recycling of used electrical and electronic equipment.
For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service,
the shop where you purchased the product or your sales representative.
The statements quoted above are only fully valid for equipment
which is installed and sold in the countries of the European Union and is covered by the directive 2002/96/EC. Countries outside the European Union may have other regulations regarding
the disposal of electrical and electronic equipment.
III
Overview of handsets
Gigaset S 1 professional
1
14
2
15
3
4
5
6
7
8
16
9
10
11
12
13
1
Receiver inset
9
Hash key
2
Display
10
Star key
3
Display keys
11
Speed dialling key
4
Control key
12
R key
5
Talk key
13
Microphone
6
On-hook and on/off key
14
Attachment clip
7
Speakerphone key
15
Ringer loudspeaker
8
Message list
16
Battery compartment
cover
How to use the keys: Æ page 10
I
Gigaset SL 1 professional
1
2
U
Ð
INT 1
20.04.03
{
09.45
¨
3
4
5
6
7
8
9
10
11
12
13
14
1
Receiver inset
2
Display
9
Hash key
3
Display keys
10
Star key
4
Control key
11
Speed dial key
5
Talk key
12
R key
6
On-hook and on/off key
13
Microphone
7
Speakerphone key
14
Connection jack for headset and PC interface
(Æ page 30)
How to use the keys: Æ page 10
II
8
Message key
Contents
Contents
Overview of handsets . . . . . . . . . . . . . . . . . . . . . . . . . . I
Gigaset S 1 professional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I
Gigaset SL 1 professional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . II
Operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . 1
Conducting calls – the basic functions . . . . . . . . . . . 1
Activating/deactivating the handset. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
First seize the line, then dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dial first, then seize the line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual number redial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Callback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enquiry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Answering a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Placing a call in a call pickup group . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ending a call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call forwarding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating or deactivating the keypad lock . . . . . . . . . . . . . . . . . . . . . . .
Leaving the radio network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
3
3
3
4
5
6
7
7
7
9
9
Description of the keys. . . . . . . . . . . . . . . . . . . . . . . . 10
Function keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
R-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
11
11
12
Putting the handset into service . . . . . . . . . . . . . . . . 13
Removing the protective cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inserting the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Charging and using the batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating and charging times of the batteries . . . . . . . . . . . . . . . . . . .
Permitted batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fitting the attachment clip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the handset display language . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the system display language. . . . . . . . . . . . . . . . . . . . . . . . . . .
13
13
14
15
15
16
16
17
V
Contents
Setting the handset . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Setting the handset volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the ringer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Advisory tones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the ringer echo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating and deactivating silent alert . . . . . . . . . . . . . . . . . . . . . . . . .
Sound Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recording a melody . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Playing a melody . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Editing an entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating or deactivating the ringer . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating or deactivating the warning tone . . . . . . . . . . . . . . . . . . . . .
Activating/deactivating automatic call answering . . . . . . . . . . . . . . . . .
Setting the date and time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Editing the idle display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resetting the defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC interface (Gigaset SL 1 professional only) . . . . . . . . . . . . . . . . . . . .
18
19
21
22
22
23
23
23
24
25
25
26
26
27
28
30
Conducting calls – enhanced functions . . . . . . . . .31
Speakerphone mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voice dialling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Number redial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System speed dialling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Individual system speed dialling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System telephone directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Handset telephone directory/speed dialling list. . . . . . . . . . . . . . . . . . .
E-mail directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Directed assignment of an MSN (multiple subscriber number) . . . . . .
Making calls using identification codes . . . . . . . . . . . . . . . . . . . . . . . . .
Using the handset as a second line. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deactivating the phone number display . . . . . . . . . . . . . . . . . . . . . . . .
Directed call transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating/deactivating do not disturb . . . . . . . . . . . . . . . . . . . . . . . . . .
Call charge display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call trace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Entrance telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TDS telephone data service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating control relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sending a signal to the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External call forwarding with a multiple subscriber number . . . . . . . . .
Using night service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using dual-tone multifrequency signalling. . . . . . . . . . . . . . . . . . . . . . .
Parking/activating calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VI
31
32
34
36
36
37
38
40
41
42
43
43
44
45
45
46
47
49
49
50
51
52
53
54
Contents
Conducting calls – with multiple users. . . . . . . . . . 55
Call waiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call waiting tone off/on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disabling/enabling automatic call waiting . . . . . . . . . . . . . . . . . . . . . . .
Override. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transferring calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Placing a call on hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Toggling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conducting a conference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the second call function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
55
56
57
57
58
60
60
61
64
Group functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Activating/deactivating group calls . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ringing group on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UCD (Universal Call Distribution) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mulap group (Multiple Line Application) . . . . . . . . . . . . . . . . . . . . . . . .
65
67
68
71
Message functions . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Leaving a message/advisory message . . . . . . . . . . . . . . . . . . . . . . . . .
Sending/calling text messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Answering a message or voice-mail message . . . . . . . . . . . . . . . . . . .
Caller list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
74
75
77
79
Additional functions . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Handset alarm clock function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Handset appointment reminder function. . . . . . . . . . . . . . . . . . . . . . . .
System appointment function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using predictive text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
81
82
85
86
87
Telephone blocking. . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Handset telephone lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Telephone lock code programming . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Locking/unlocking the handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Central telephone lock/locking/unlocking other handsets . . . . . . . . . . .
88
89
90
91
System functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Calling functions via the menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Calling functions via codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Functions and codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
VII
Contents
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the handset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical data and accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EU-guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
96
97
97
98
98
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
VIII
Operating instructions
Step by Step
Operating instructions
These operating instructions describe your handset and
its functions on your communications system.
All functions that can be performed via your handset are
described here. If some of the required functions are
not available on your handset, it may be due to one of
the following:
• The function is not configured for you or your handset - please contact your system administrator.
• Your communications platform does not feature this
function - please contact your Siemens contract
partner to upgrade.
Conducting calls – the basic
functions
You can use your handset to make both internal and external calls.
Internal calls are calls that
• you make within the range of a communication system, e. g. within your company,
• you make between networked communication systems, e. g. to different company locations.
External calls are calls that you conduct with users of
the public telephone network.
1
Conducting calls – the basic functions
Step by Step
Activating/deactivating the handset
a Press the On-hook key until the activation or deactivation is confirmed by a crescendo tone sequence.
Note:
• The handset can only be fully switched off
when removed from the charging shell.
• After switching off a mobile phone, place it in
the charging shell; with PIN "0000" it will
switch on immediately and is ready for operation. If the PIN is not "0000", you must first
enter the PIN. Only then is the mobile phone
ready for operation.
• When a handset that is ready for operation is
placed in the charging shell it goes to idle status and shows the idle display.
If your preferred language for the display texts is not
set, you can set this yourself.
If a mobile phone that is switched off is placed in the
charging shell, it will switch on.
If the PIN is still the same as the factory default (0000),
the phone is ready for operation.
If the PIN is not the same as the factory default, the PIN
must be entered to make the mobile phone ready for
operation.
Displaying the connection quality
The strength of the incoming signal is displayed by the
"receive field strength" icon in on or message status:
|
Ò
Ñ
Ð
No receive field strength
Low receive field strength
50% receive field strength
100% receive field strength
The radio range is different indoors and outdoors
(Æ page 97). Please consult your system administrator
in the event of range problems.
2
Step by Step
First seize the line, then dial
c or u Press the Talk or Speakerphone key.
o
p
Enter the required phone number. The user will be
called.
Typing errors cannot be corrected. If you make a typing
error: press the On-hook key.
The user answers. Conduct the call.
Dial first, then seize the line
o if necessary X
Enter the required phone no. and correct individual characters as necessary using the "Delete" Display key.
if necessary © The following functions are available while you are entering the phone number:
• "Insert Pause" (Insert a dial pause, e.g. between the
prefix and phone number or when checking a mailbox.)
• "Insert TBR" (irrelevant)
• "Copy to Directory" (save the phone number in the
handset’s redial list)
Note:
This dialling preparation function is also available
with number redial and dialling using the handset redial list.
c or u Press the Talk key or Speakerphone key within 30 seconds. The user will be called.
p
The user answers. Conduct the call.
Manual number redial
With Gigaset S1 professional the last five numbers dialled, or with Gigaset SL 1 professional the last ten
numbers, are automatically saved in the redial list.
z Call the redial list.
D or E Press the top or bottom of the control key to select the
required phone number.
c Press the Talk key.
3
Step by Step
Callback
This function enables you to call a user who does not
answer or whose line is busy. The Callback function enables you to contact him as soon as he hangs up or reuses his telephone. Please note that a line is signalled
as busy when it is being called by another user. You can
continue to use your handset without restriction when
a callback has been booked.
You can also send a callback request as a message. This
function can also be called by entering the code
(Æ page 92).
Booking a callback
p
Callbck
The number is dialled. You hear the busy tone or the
user does not answer.
Save the callback request.
a Press the On-hook key to end the process.
You receive a Callback call
You will receive the callback, as soon as the user you
want has hung up or the first time he uses his telephone. The following appears on your handset display
"Callback:...".
The connection is set up.
Note:
Callbacks are repeated until a connection is established or until the callback is deleted. A handset can initiate up to five callbacks and can be
the destination for up to five callback requests.
If these conditions are met, any further callbacks are rejected.
Deleting a callback request
Menu
><
4
Service?
Call the system menu.
[ Select and confirm the menu item.
Step by Step
><
More features?
><
#58=View
callbacks?
Mnu
><
Delete?
Call the additional menu.
Enquiry
You interrupt your call to conduct an enquiry with a user (including external users) and then resume the original call.
R or
p
Enquiry
You are on a call.
Activate enquiry. The current call is placed "on-hold", so
that the first user waits.
o Enter the phone number for the enquiry call.
p
The number is dialled. The user answers. The enquiry
starts.
The enquiry is ended and you return to the call "onhold"
either: The second user hangs up. You are reconnected to the
first user.
or: Option 1
Menu
><
Quit and return?
Option 2
R
Press the R key.
You are reconnected to the first partner. The second
partner hears the busy tone and hangs up; a Gigaset
handset hangs up automatically.
However, you can also
• toggle between the partners (Æ page 60),
• set up a conference (Æ page 61) or
• transfer the waiting partner to the second partner
(Æ page 58).
5
Step by Step
The second user is busy or does not answer
Î Cancel the callback. You are reconnected to the first
partner.
During the enquiry you can
• book a callback (Æ page 4),
• activate call waiting (Æ page 55) or
• override(Æ page 57).
Answering a call
Your handset rings and/or vibrates. The caller information appears on the display. The name and/or telephone
number of the caller can be displayed. The following options are available for answering a call:
k
The handset is in the charging shell: remove the handset from the charging shell (functions only if "Auto Answer" is active Æ page 26).
cor u The handset is not in the charging shell. Press the Talk
key or Speakerphone key.
When you have answered the call you can
• transfer the call (Æ page 58),
• place the call on hold and consult with someone
else in the room (Æ page 60),
• place the call on hold and call a second partner
(Æ page 5) in order to forward or toggle the call
(Æ page 60) or to set up a conference (Æ page 61).
Rejecting a call
If you do not wish to be disturbed, you can reject the
call.
Reject call
6
Confirm the message displayed with one of the two
Display keys. The call is rejected and the caller hears the
busy tone.
Step by Step
Placing a call in a call pickup group
You can use your handset to pick up calls to telephones
within your call pickup group (set by the service engineer). This is also possible when you are conducting a
call.
Prerequisite:
You hear that a telephone in your call pickup group is
ringing.
c Press the Talk key. The message "Call for:" appears on
the display.
Menu
><
Group Pickup?
p
Conduct the call.
Ending a call
a or k Press the On-hook key or place the handset in the
charging shell.
The call charges are displayed, depending on the communication system.
Call forwarding
This function is for when you leave your desk for a while
and want certain calls to be forwarded to your new location. The forwarding destination for internal calls can
be any internal or external phone number. The destination number is usually an external phone number because you can be reached internally anytime by means
of your handset.
Activating call forwarding
Menu
><
Forwarding on?
7
Step by Step
either:
><
1=all calls?
or:
><
2=external
calls only?
><
3=internal
calls only?
or:
continue:
o Enter the destination phone number.
Save
Save the settings.
Note:
The external code must be entered before external phone numbers.
If the service engineer has activated DTMF DID,
you can also forward calls to these external
phone numbers.
Deactivating call forwarding
Prerequisite:
The room monitor function is activated.
Menu
><
8
Divert cancelled?
Step by Step
Activating or deactivating the keypad
lock
This feature protects against accidentally pressing buttons when the handset is in a pocket, for example. The
keypad lock turns off automatically when a call comes
in and turns back on when the call has ended.
# Press the hash key until the activation or deactivation is
confirmed by a crescendo tone sequence.
A key icon on the display indicates that keypad lock is
active.
Leaving the radio network
After leaving the radio network
The base name flashes on the display. The handset repeatedly attempts to synchronise with a base. The intervals between synchronisation attempts increase on
account of the integrated power saving function.
You can switch off your handset to save the battery. The
date and time settings will be lost.
9
Description of the keys
Function keys
The following function keys are available:
Key
Name
Use
a
On-hook and
on/off key
•
•
•
•
c
Talk key
•
•
•
•
u
Speakerphone
key
•
•
•
•
?
*
#
C
R
10
End a call
Cancel functions
Jump back to the previous menu (only
following © )
Activate or deactivate the handset
Answer a call
Dial a phone number
Switch from speakerphone mode to
handset mode
Access telephone system functions
Answer a call
Dial a phone number
Switch from handset to speakerphone
mode
Access telephone system functions
Message list
Access message lists
Star key
Activate/deactivate the ringer
Hash key
Activate/deactivate keypad lock
Speed dialling
list
Access speed dialling list
R key
R key function (Æ page 11)
R-key
The R-key provides access to the following functions depending on how it
is operated:
Operation
Function
Press
Enquiry function:
Make an enquiry (alternative to "Enquiry" Display key)
Press and hold (min. 1 second)
R key function:
• Insert a pause (e. g. between
the prefix and the phone
number, or when checking a
mailbox)
• End connection to a mailbox
(e. g. when performing a callback, setting up a conference
or transferring a call)
Control key
The control key is assigned different functions depending on the operating
situation:
Control
key
In idle status
In lists and
menus
In an input
field
E
Use voice dialling
Next menu level
up
Move the cursor
up one line
D
Open the mobile’s telephone
directory
Next menu level
down
Move the cursor
down one line
G
Open the menu
Select an entry
(OK)
Move the cursor
right
Next menu level
up, cancel
Move the cursor
left
F
11
Display keys
The handset has two Display keys, each with one or two functions. When
the key is allocated two functions, press the right or left side of the key to
select the corresponding function. Display key assignment depends on the
operating status. A function can be represented by text or an icon.
Icon
Name
Use
©
Menu
Call the handset menu
X
Delete
Delete the entry character by character from right to left
z
Number redial
Open a list of the last five phone
numbers called
J
Message list
Open message list
Î
Go Back
Go back to the next highest menu
level, cancel
n
Internal
Stop entering the phone number
after the first digit
[
OK
Confirm the selected menu item
Up/down
Scroll up or down to select menu
items
Record
Record voice pattern
Phonebk
Telephone directory
Call the system telephone directory
Enquiry
Consultation
Make a consultation
Toggle
Toggle
Toggle between two partners
2ndCall
2nd call
Accept call waiting
Callbck
Callback
Conduct a callback with a second
partner
Change
Change
Change the configuration
Save
Save
Save entries
Dial
Dial
Dial the digits entered
Send
Send
Send information message
Menu
System menu
Call the system menu
Additional menu
Call the additional menu
<>
Record
Mnu
12
Putting the handset into service
Removing the protective cover
Remove the protective cover from the display before
putting the handset into service.
Inserting the batteries
Two batteries are supplied with the Gigaset S1 professional while Gigaset
SL 1 professional comes with a single battery pack. The batteries are supplied uncharged. They are charged in the handset.
Note:
• Please observe the safety notes on the back cover.
• Only use approved batteries.
• Always replace both batteries at the same time and only use
two batteries of the same type/ from the same manufacturer!
• Open the battery compartment in a dust-free environment only.
• Your telephone directory entries and all settings remain stored
even if you remove the batteries. The date and time settings
will be reset.
• Only remove the batteries if they are defective. Any unnecessary removal of the batteries reduces their lifespan.
Opening the battery compartment and inserting the batteries
Press down on the ridged surface and slide the cover from the battery
compartment. Insert the approved battery(ies).
13
Closing the battery compartment
Put the cover back in place and slide it onto the battery compartment until
it engages.
Charging and using the batteries
To charge the batteries, insert the handset into the charging shell with the
keypad facing forwards.
Caution:
Only use the relevant approved power supply units for operating
the charging shell in Gigaset S1 professional.
(Order numbers see Æ page 97)
Use the Gigaset Charger SL charging shell with integrated power
supply for Gigaset SL 1 professional
(Order numbers see Æ page 97).
The charging status is indicated by the charge status display. This flashes
during charging:
=
e
V
U
Batteries empty
Batteries 33% charged
Note:
• Initial charging: Charge the batteries for at least 5 hours without a break, regardless of the charging status icon. Without replacing it in the charging shell, use the handset until the "battery low" beep is heard. This action aligns the charge status
display with the operating times of the batteries.
• To attain full operating and charging times: Without replacing it
in the charging shell, use the handset until the "battery low"
beep is heard.
• For future charging: you can place your handset in the charging
shell each time it is used. Charging is electronically controlled
which ensures that the batteries are charged optimally.
14
Operating and charging times of the batteries
The operating times are only achieved after several charging and discharging cycles.
Capacity (mAh)
Stand-by mode
(hours)
700 (“Sanyo Twicell 650”: 650) 170 (7 days)
Talk time
(hours)
Charging
time
(hours)
over 13
approx. 5
Talk time
(hours)
Charging
time
(hours)
Capacity (mAh)
Stand-by mode
(hours)
700
approx. 250 (10 days) approx. 15
approx. 2,5
Permitted batteries
The following batteries are approved for use with the Gigaset S1 professional:
Nickel Metal Hydrid (NiMH)
Sanyo Twicell 700
Sanyo Twicell 650
Panasonic 700 mAh
GP 700 mAh
YDT AAA SUPER 700
VARTA PhonePower AAA 700 mAh
The following battery pack is approved for Gigaset SL 1 professional:
Lithium-Ion (LiIon), 700 mAh
15
Step by Step
Fitting the attachment clip
Press the attachment clip onto the back of the handset
until the tabs on the sides engage in the recesses on
the phone.
Setting the handset display language
If your preferred language for display texts is not set as
the default, then you can set this yourself.
Open the main menu
© or G Open the main menu of the mobile phone.
Open the submenu
either:
DE
H/Set Settings
or:
DE
Einstellungen
Open the submenu
either:
DE
Language
DE
Sprache
or:
16
Step by Step
Select a language
DE
Deutsch
...
[ Select and confirm the language you require.
Note:
For how to return the telephone to the default
settings (Æ page 28).
Setting the system display language
If you wish to change the language of the display texts,
then you must also change the system language on the
handset. A different language can be set for every handset on the system.
Menü
><
Service?
><
More features?
><
*48=
Select language?
><
11=German
...
[ Select and confirm the language you require.
17
Setting the handset
Step by Step
Setting the handset
You can change the standard settings of the handset if
you are not happy with them.
Setting the handset volume
When selecting the menu, the tone sounds at the current setting in speakerphone mode. You can choose between five volume levels in handset mode and three
volume levels in speakerphone mode.
__Handset Volume__
1
2
f
B
Î
g
1 Volume in speakerphone mode
2 Volume in handset
mode
Save
DE
Audio Settings
DE
Handset Volume
F G Fix the setting.
D Move the cursor down one line.
...
Save
Save the settings.
18
Setting the handset
Step by Step
Setting the ringer
Setting the ringer volume and melody
When selecting the menu, the ringer sounds at the current setting. You can choose between three ringer volumes, as well as a crescendo ring (volume increases
gradually) and no ringer. The ten ringer melodies cannot
be stored in the communication system.
With Gigaset SL 1 professional up to 16 additional melodies can be used. Melodies 11 to 26 are polyphone
melodies, which must first be loaded via PC interface or
recorded via the Sound Manager.
1 Ringer volume
1
2
3
2 Ringer melody
___Ext. Calls___
E1
f
Announce
On
Save
Time C.
g
3 Time control activation function for the
ringer volume
Display when ringer is deactivated.
In order to better differentiate between your handset’s
ringing tones, select the following settings:
• Ext. Calls
• Internal Calls
• Appointments
• Alarm
• All
G Open the main menu of the mobile phone.
DE
Audio Settings
[ Select and confirm the required menu item.
DE
Ringer Settings
DE
Ext. Calls
...
F G Set volume.
F G Set melody.
19
Setting the handset
Step by Step
•
•
•
Tones: 1 to 3 (recommended for internal calls)
Melodies: 4 to 10 (recommended for external calls
with Gigaset S1 professional)
Melodies: 4 to 26 (recommended for external calls
with Gigaset SL 1 professional)
Please make sure that you have picked up the call
before holding the phone to your ear. This is to
ensure that the loud ringing tone does not cause
damage to your hearing.
either:
Save the settings.
Save
or: Setting the time control for the ringer
You can select a different ringer volume for a specific
length of time in this menu (e.g. during the night).
Note:
Please take account of the special features of
the handset‘s internal clock.
1
2
3
Time ctrl::
From:
Until:
Î
Time C.
On
00:00
00:00
f
g
1
Time control status
2
Start of the time
frame
3
End of the time
frame
Save
Call the ringer time control menu.
F On G Fix the setting.
...
Save
Save the time control settings.
Save
Save the ringer settings.
a Press and hold the On-hook key to end the process.
20
Setting the handset
Step by Step
Advisory tones
The advisory tones have the following meaning:
Advisory
Meaning
Key tone
Every keystroke is confirmed
Confirmation
tones
•
•
•
Battery tone
1
2
3
Confirmation tone (crescendo
tone sequence) when saving inputs/settings and when placing
the handset in the charging shell
Error beep (decrescendo tone
sequence) to signal incorrect inputs
End-of-menu beep at the menu
end
The battery must be charged
___Advisory Tones___
f On g
Key tone:
On
Con. tone:
On
Battery
Save
Î
1
Key tone status
2
Confirmation tone
status
3
Battery tone status
DE
Audio Settings
DE
Advisory Tones
F G Fix the setting.
...
Save
Save the settings.
21
Setting the handset
Step by Step
Setting the ringer echo
This function enables you to set the tone quality for the
longer melodies (4 to 10). When ringer echo is activated, melodies will be played with an echo.
G Open the main menu of the handset.
DE
Audio Settings
DE
Ringer Echo
Ringer echo is activated.
The activated function is ticked. It can be deactivated by
selecting the option once more.
Activating and deactivating silent alert
In Gigaset SL 1 professional. you can activate the silent
alert feature in addition to ringer settings or else instead
of ringer settings.
You can deactivate the ringer settings once you have activated the silent alert (Æ page 25).
© or G Open the main menu of the handset.
DE
Audio Settings
[ Select the menu item and confirm.
DE
Silent alert
Silent alert is active.
The activated function is ticked and can be deactivated
by selecting it once more.
Note:
If you have called up the Service menu, then silent alert will not be activated for an incoming
call if "Turn ring off" and "Silent alert (on)" have
been set.
22
Setting the handset
Step by Step
Sound Manager
You can use the microphone of Gigaset SL 1 professional to record polyphonic melodies (max. length 4 seconds) or download melodies via a data cable
(Æ page 30). Up to 16 melodies can be saved.
Recording a melody
DE
Audio Settings
DE
Sound Manager
<New Sound>
[ Confirm.
Record Sound?
[ Confirm.
End
Save
Press the display key or wait 4 seconds.
Press the display key.
[ Confirm and enter the name of the melody.
Edit Entry
Save
a
Press and hold down the on-hook key to end the process.
Playing a melody
DE
Audio Settings
DE
Sound Manager
D E Select a melody.
Play
a
23
Setting the handset
Step by Step
Editing an entry
DE
Audio Settings
DE
Sound Manager
D E Select a melody.
© Open the submenu.
Volume
[ Confirm to change the volume.
or
DE
Edit Entry
[ Confirm to change the name.
or
D E View Entry
[ Confirm to display the file name.
or
DE
24
Delete Entry
[ Confirm to delete the entry.
a
Setting the handset
Step by Step
Activating or deactivating the ringer
Deactivating the ringer
* Hold down the key until a confirmation tone is sounded.
The ringer is deactivated.
Activating the ringer
* Hold down the key until a confirmation tone is sounded.
Note:
The ringer cannot be activated with the star key
if it was deactivated via the menu.
Activating or deactivating the warning
tone
When you activate the warning tone, all other tones are
deactivated. An incoming call is signalled by this brief
tone.
If the handset is in a call pickup group, a pickup call is
also signalled by the warning tone.
Activating the warning tone
* Hold down the key for a few seconds. A confirmation
tone is sounded.
Beep on
Press the Display key within three seconds.
The warning tone is activated.
Deactivating the warning tone
* Hold down the key for a few seconds. A confirmation
tone is sounded.
Note:
The warning tone cannot be activated if the ringer was deactivated.
25
Setting the handset
Step by Step
Activating/deactivating automatic call
answering
This function allows you to accept calls by removing the
handset from the charging shell.
DE
H/Set Settings
DE
Auto Answer
Automatic answering is activated.
The activated function is ticked. It can be deactivated by
selecting the option once more.
Setting the date and time
We recommend setting the date and time to ensure the
correct time/date is recorded for all calls. You can
choose between 12-hour display (am, pm) and 24-hour
display.
Note:
Do not switch off the handset after you have
made the settings, otherwise the date and time
will be reset.
Check the date and time and reset from time to time
where applicable.
© Open the menu.
DE
Calendar/Clock
DE
Date/Time
o Enter the date, e. g. 22.09.2002 = 220902.
o Enter the time, e. g. 19:05 = 1905.
26
Setting the handset
Step by Step
F 24 h G Define the display mode (24 h, 12 h).
Save
Save the settings.
Editing the idle display
You can change the base station name that is displayed
in idle status. The handset must be registered at the
corresponding base.
DE
H/Set Settings
DE
Select Base
DE
<Base>
The selected base is activated.
The activated base is ticked. It can be deactivated by selecting another base.
Change
Change settings.
Edit Name: X Delete text.
o and poss. X
Save
Enter the required text and correct individual characters
as necessary using the "Delete" Display key.
Save settings.
aa Press the On-hook key twice to turn the handset off and
back on.
The changed base station name will now be displayed
in idle status.
27
Setting the handset
Resetting the defaults
This function allows you to reset your mobile phone to the defaults, e.g. if
you want to pass it on to someone else or reset it. The following table
shows the handset’s default settings:
Setting
Explanation/notes
Levels
Audio Settings
Ringer volume
5
Default
state
5
Ringer melody
Melody enhancement
10
-
1
on
Vibrating alert (SL 1 only)
Time control for ringer
-
on
off
Warning tone
Handset volume
3
off
1
Volume in speakerphone mode
Name announcement
5
-
3
off
Alarm/Appointment
Appointment name
-
off
deleted
Key tones, audible each time a key is pressed.
on
Battery tone, audible approx. five
minutes before the battery runs out.
Confirmation tone, indicates whether actions were successful or unsuccessful.
on
Auto Answer
28
on
Define whether the Talk key must
be pressed to accept a call when
the handset is removed from the
charging shell.
Select Base Select the base
-
on
4
Screen
Picture
Display in idle status
-
"Best
Base"
off
Character
Set
Available character set
-
Standard
Language
Select different languages:
14
19
English
or
German
Default
state
Resetting the defaults deletes the redial and direct call numbers and
resets the sound settings. The registration (logon) and the handset
PIN are retained.
-
Setting the handset
Step by Step
The handset features are handled as follows when resetting the defaults:
Feature
Action
Sound settings
are reset
Speed dialling list
is retained
System registration
is retained
Telephone directory
is retained
Telephone Services menu depends on the version
Redial list
is deleted
DE
H/Set Settings
DE
Reset Handset
[ Select and confirm the menu item. A security check
question appears.
Yes
Confirm the security check question The handset is returned to the default.
Note:
For information about deleting the telephone
directory see: Æ page 40.
29
Setting the handset
PC interface (Gigaset SL 1 professional only)
The Gigaset SL 1 professional handset can be connected to your computer
via a Siemens data cable. Your computer can then communicate with your
Gigaset SL 1 professional using the “Siemens Data Suite” program (freeware available for download at http://www.my-siemens.com\mysiemens)
and access the following handset parameters and lists:
Displaying parameters
• Software version
• Type
• Vendor code
Read/write access to
• the phonebook
• the e-mail directory
• the network provider list
• the appointments list
• the redial list
Read/write access to other parameters
• ringer settings
• volume settings
• loading screensavers
• loading melodies
• conducting and accepting calls
Data transfer
Large volumes of data are transferred between the handset and the external device for certain functions. In this case, the handset is switched to
data transfer mode and data transfer appears on the display. In this mode,
no inputs are possible via the keyboard and incoming calls are ignored.
The handset is switched to data transfer mode by:
• activating read/write access to the phonebook
• activating read/write access to the e-mail directory
• activating read/write access to the network provider list
• activating read/write access to the appointments list
• activating read/write access to the redial list
• loading screensavers
• loading melodies
The handset automatically switches to idle if a fault occurs in the
course of transferring data.
30
Conducting calls – enhanced functions
Step by Step
Conducting calls – enhanced
functions
Speakerphone mode
Features
Speakerphone mode offers you the following advantages:
• Other persons can listen to and participate in the
call.
• Your hands are free.
• When dialling, you can hear the ring tone, for example, without having to lift the handset to your ear.
Speakerphone mode can be used effectively up to a
background noise level of 50 dB (A).
Activating speakerphone mode
Speakerphone mode can be activated during a call,
when dialling or when answering a call:
u Press the Speakerphone key.
Note:
Speakerphone mode must be switched off before holding the telephone directly to your ear
again. In this way you can avoid causing damage
to your hearing.
Setting the volume
The volume can be set during a call:
u Press the Speakerphone key once more.
F or G Within three seconds: Press the left or right side of the
control key to reduce or increase the volume.
Save
Within three seconds, as necessary: Save the volume
set.
31
Step by Step
Deactivating speakerphone mode
You can deactivate speakerphone mode and switch to
handset mode during the call:
Note:
If you wish to replace the handset in the charging shell during a call, e. g. because the battery
is empty, hold down the Speakerphone key.
Voice dialling
With the voice dialling function, you can dial a number
simply by saying the partner’s name. You do not need
to manually dial a phone number.
For this function, you will need to record a voice pattern,
in other words, your voice saying the name will be
saved in the handset. Up to four users can save a voice
pattern for each entry. The user must be identified, i.e.
as User 2, before recording.
A total of 29 voice patterns can be saved in Gigaset S1
professional and 23 voice patterns in Gigaset SL 1 professional for telephone directory entries. An entry that
has a corresponding voice pattern is marked with a
mouth in the voice telephone directory.
Recording a voice pattern for an existing telephone
directory entry
You should record your voice pattern in a quiet environment. There should be about 25 cm between you and
the handset.
D Open telephone directory.
D E Select the required entry.
Voice
DE
Press the Display key.
User 1
...
Record
[ Press and confirm the Display key.
Say the name when the relevant prompt is displayed.
Repeat the name after being prompted again. The recording will be saved automatically.
32
Step by Step
A message will notify you if your voice pattern is too
similar to that of another user.
Î The message will end.
Return to the beginning of the voice recording and
record your voice pattern again.
Using voice dialling
E Press and hold the control key and then say the name.
Listening to a voice pattern
D Open the voice dialling telephone directory.
Voice
DE
User 1
...
Play
Play the corresponding voice pattern.
Changing or deleting voice patterns
D Open the telephone directory.
Voice
DE
User 1
...
G Open the menu.
either:
DE
Record Name
or:
DE
Delete Name
33
Step by Step
Note:
The phone number and name are retained after
an entry has been deleted. Other users’ voice
patterns also remain.
Changing a user name
Voice
DE
Select the menu item.
User 1
...
Change
Change the settings.
o Enter a new name.
Save
Save the settings.
Number redial
With Gigaset S1 professional the last five numbers dialled, or with Gigaset SL 1 professional the last ten
numbers, are automatically saved in the redial list.
If you tried to call a party from the handset’s telephone
directory, the name of the party is displayed in case of
number redial.
Automatic redial
The phone number is automatically redialled ten times
at 20 second intervals. Speakerphone mode is automatically activated, the Speakerphone key flashes. The
function is deactivated after ten unsuccessful attempts
and when a call is made in the interim.
© Open the menu.
34
Step by Step
DE
Automatic Redial
[ Select and confirm the menu item. Automatic redial is
activated.
either:
p
The user answers and you conduct the call.
or:
Off
If you wish to cancel the function: press the Display key
or any key.
Deleting a phone number from the redial list
DE
© Open the menu.
Delete Entry
[ Select and confirm the menu item. The telephone
number is deleted.
Adding a telephone number to the redial list
DE
© Open the menu.
Copy to Directory
number is deleted.
o Enter the name (max. 16 characters), change the phone
number is necessary and enter the date.
© Open the menu.
Save Entry
[ Save the entry.
35
Step by Step
System speed dialling
A system speed dialling destination is a call number you
dial using a code, e.g. the external phone number (0 28
21) 34 56 78 using code 243. System speed dialling destinations are defined by the system administrator.
Codes from 000 to 999 can be used.
This function can also be called by entering the code
(Æ page 92).
Dialling a speed dialling destination
Menu
><
Service?
><
* 7=Use speed dialing?
o Enter the required code (3 digits, 000 - 999).
Note:
The saved speed dialling destinations and the
associated codes can be obtained from the organisational unit responsible for administering
the communication system.
Individual system speed dialling
You can save up to ten external phone numbers for your
handset as speed dialling destinations. These speed dialling destinations are dialled using a 2-digit code (00 to
09). Please note that you may need to save an external
code in front of the phone number.
(Æ page 92).
Setting up an individual speed dialling destination
Menu
><
36
Service?
Step by Step
><
* 92=Change Speed
Dial?
Abb. dial no:
> Call the first destination.
> Call the next destination.
Mnu
><
Change entry?
o Enter the external phone number (with external code).
The key "#" means that the subsequent digits are sent
as DTMF tones.
Save
Save the settings.
Dialling an individual speed dialling destination
Menu
><
Service?
><
* 7=Use speed dialing?
Abb. dial no:
*o Enter the code for the speed dialling destination.
System telephone directory
If the system administrator has entered a name for at
least one internal user or system speed dialling destination, then you can use the system telephone directory
for dialling purposes.
Calling the system telephone directory
Phonebk
Call the system telephone directory. The first entry appears.
37
Step by Step
Finding an entry
o Enter the first letters of the name you are looking for.
The name search begins.
The search result becomes more precise as each letter
is entered, i.e. the number of names found is reduced.
Only the first letter of a key can be entered.
> < Select the user you want.
Dialling the entry
[ Confirm your selection. The selected number is called.
Quitting the redial list
Î Press the Display key.
Note:
Phone numbers dialled from the "System telephone directory" are not stored in the redial list.
Handset telephone directory/speed
dialling list
A total of up to 200 entries can be saved in the telephone directory, the e-mail directory and the speed dialling list.
Operation of the telephone directory and the speed dialling list is identical. The anniversary function is not
available in the speed dialling list, however, but you can
allocate a number for up to nine new entries. The external code must be entered before external phone numbers, e. g. "0".
Save the entry.
DE
D or C Open the telephone directory or speed dialling list.
New Entry
o Enter a phone no.
D o Jump to the name field and enter the name and, if re-
quired, the anniversary. Predictive text can be used for
this (Æ page 86).
38
Step by Step
either (for telephone
directory):
DE
© Open the menu.
[ Save the entry.
Save
or (for speed dialling list):
F 0 G Define settings.
Save
Save settings.
Finding and dialling an entry
E/D or o You can scroll to the required entry or enter the first letter of the relevant entry.
If necessary, press a key several times in succession to
enter the required letter.
either:
c Press the Talk key. The assigned phone number is dialled.
or:
DE
G Open the menu.
Display Number
[ Select and confirm the menu item. The number is displayed.
Changing an entry
E/D or o You can scroll to the required entry or enter the first let-
ter of the relevant entry. If necessary, press a key several times in succession to enter the required letter.
G Open the menu.
either:
DE
Edit Entry
DE
Copy and Edit
or:
o Enter changes.
39
Step by Step
DE
© Open the menu.
[ Save the entry.
Save Entry
Deleting an entry or telephone directory/speed dialling list
D or C Open the redial list or the net carrier list.
D or E Select the required telephone number.
© Open the menu.
either:
DE
Delete Entry
number is deleted.
or:
DE
Delete List
[ Select and confirm the menu item. A security check
question appears.
Yes
Confirm the security check question. The telephone directory/speed dialling list is deleted.
E-mail directory
You can save e-mail addresses in the e-mail directory.
Entries in the e-mail directory are managed the same
way as telephone directory entries.
Saving a new e-mail address
D Open the telephone directory
DE
<E-MailDirectory>
DE
New Entry
To use the help function:
© Open the menu.
D E [ Select and confirm one of the following menu items:
•
•
•
40
Insert ' . '
Insert '@'
Predictive text, Æ page 86
Step by Step
o Enter address.
DE
© Open the menu.
[ Save the settings.
Save Entry
Changing an e-mail address
DE
<E-MailDirectory>
View
Change
DE
View entry.
Change entry
© Open the menu.
Save Entry
[ Save the settings.
Directed assignment of an MSN (multiple subscriber number)
Multiple subscriber numbers are phone numbers belonging to an ISDN multiple device line. They are used
for the directed addressing of terminals, for example
when a fax machine has a separate number. Before selecting an external connection, you can directly assign a
configured multiple subscriber number. This then appears on the called party’s display.
(Æ page 92).
41
Step by Step
Menu
><
Service?
><
* 41=Temporary
MSN?
MSN no.111
o Enter the required multiple subscriber number.
111:
o Enter the required external phone number. The phone
number is dialled.
Making calls using identification
codes
In the case of calls you make to external partners, you
can enter and charge the call costs on the basis of individuals, customers, accounts and private calls, e.g. by
means of account codes. The account code (ACCT) can
contain up to 11 characters and is included in the data
printout. The ACCT is only transferred after a call has
been completed. The ACCT can be entered before and
during the external call.
(Æ page 92).
Menu
><
Service?
><
* 60=Account code?
Project Code:
o Enter the required account code (optional).
Save
Please dial.
Save the settings.
o Enter an external phone number. The phone number is
dialled.
Note:
If a call is transferred, the costs are still assigned
to the ACCT entered.
42
Step by Step
Using the handset as a second line
You can use your mobile phone for an outgoing call as if
it were another line (temporary phone).
(Æ page 92).
Menu
><
Service?
><
* 508=Temporary
Phone?
Home Extn. no.:
o Enter the internal phone number for the relevant line.
PIN no:
<Name>
o Enter the code (lock code) for the relevant line.
<Name>:...
o Enter the required phone number. The phone number is
If there is no personal code for the relevant line, the system will prompt you to enter the code.
dialled.
The "Temporary phone" function is discontinued again
after the call is complete.
Deactivating the phone number display
Your service engineer can deactivate the display of your
phone number and name on the called party’s display
for external outgoing calls. You can also activate and deactivate the phone number display on your own handset yourself.
Deactivating the phone number display
Menu
><
Suppress call ID?
Call ID suppressed
43
Step by Step
Activating the phone number display
Menu
><
Restore caller ID?
Call ID restored
Directed call transfer
You can transfer calls to other telephones to your handset. This is also possible when you are conducting a call.
(Æ page 92).
Another telephone rings.
Menu
><
Service?
><
* 59=Pickup - directed?
[ Select and confirm the menu item. The called user is
displayed.
Mnu
either:
><
Accept call?
or:
Note:
If several users are called simultaneously, only
the first user called is displayed. However, you
can transfer by entering the phone number of
any of the users called.
><
Select
extension?
continue:
p
44
Conduct the call.
Step by Step
Activating/deactivating do not disturb
You can block calls to your handset on a temporary basis, while still being able to make calls yourself. Internal
callers hear the busy tone, while external callers reach
another telephone defined by the service engineer (intercept position). Authorised internal callers automatically override the do not disturb after five seconds.
Activating do not disturb
Menu
><
Do Not Disturb ON?
Deactivating do not disturb
Menu
><
Do Not Disturb OFF?
Call charge display
After a call has ended, the display shows the connection charges for the current call as standard. If the costs
are to be displayed continuously during an outgoing call,
this function must be requested from the carrier.
Note:
If a call is transferred, the costs are assigned to
the telephone to which the call was transferred
from this point onwards.
You can check and display the call charges for your
phone number as a total for a period that can be set by
the service engineer.
First the call charges for the last charged call are displayed. The total call charges are displayed after five
seconds.
45
Step by Step
(Æ page 92).
Menu
><
Service?
><
* 65=Show call charges?
Call trace
You can apply to your carrier for "call tracing" on malicious calls. An authorised extension is then in a position
to request the identification of the phone number.
This also works for 30 seconds after the malicious caller
has hung up. However, you should not hang up.
(Æ page 92).
p
Menu
You receive a malicious call.
Do not hang up.
><
Service?
><
* 84=Trace call?
[ Select and confirm the menu item. The caller is identified in the attendant console.
46
Step by Step
Entrance telephone
If the service engineer has set up an entrance telephone, you can speak to the door intercom and activate
the door opener from your handset.
If you are authorised to release a door, then a user can
open the door by entering a 5-digit code (e.g. by means
of a DTMF transmitter or installed keypads).
Some of the functions described below can also be
called directly by entering the relevant code
(Æ page 92).
Talking to a visitor by means of the door opener
equipment
Your handset rings.
either:
c Press the Talk key within 30 seconds. You are connected immediately to the door opener.
or:
c If more than 30 seconds have passed: Press the Talk
key.
o Enter the internal phone number for the door opener.
You are connected to the door opener.
Using the handset to open the door opener during
a call
><
Open door?
Using the handset to open the door opener without
holding a conversation
Menu
><
Service?
><
* 61=Open door?
o Enter the internal phone number for the door opener.
The door is opened.
47
Step by Step
Activating the door release
This function only works if it has been configured by the
service engineer.
Menu
><
Service?
><
* 89=Door release
ON?
o Follow the user guidance system from this point on-
wards. Enter the internal phone number of the door
opener, as well as the code and type of door release:
• 1=Enable with call,
• 2=Enable without call,
• 3=Change password.
[ Confirm your entries.
Note:
Standard code 00000. To change the code, confirm option "3=Change Password". Follow the
user guidance system.
Deactivating the door release
Menu
><
Service?
><
* 89=Door release
OFF?
48
Step by Step
TDS telephone data service
You can use your mobile phone to control connected
computers and their programs, e. g. hotel services or
information systems.
(Æ page 92).
Menu
><
Service?
><
* 42=Tel. data
service?
TDS code:
#o Press the "#" key and enter the required code (0... 9).
The connected computer responds. The computer will
guide you through the data entry process. It will process your entries directly.
Activating control relays
The service engineer can set up a maximum of 4 control
relays that enable various equipment (e.g. door opener)
to be activated and deactivated.
It is possible to access a specific control relay. Depending on the configuration, the control relays can be
• activated and deactivated automatically, or
• activated and deactivated automatically on the basis
of a timer.
Prerequisite: The service engineer has set up at least
one switch.
(Æ page 92).
49
Step by Step
Activating a control relay
Menu
><
Service?
><
* 90=Control Relay
On?
o Follow the user guidance system from this point onwards. Enter the required switch code (1... 4).
Deactivating a control relay
Menu
><
Service?
><
#90=Control Relay
Off?
o Follow the user guidance system from this point onwards. Enter the required switch code (1... 4).
Sending a signal to the network
To enable ISDN-type services/ features to be started via
analog lines (e.g. call waiting when a line is busy, threeway conference calls, etc.), you must send a signal to
the network before dialling the service code and/or
phone number.
This function can also be called directly by entering the
code ().
p
Menu
><
Service?
><
* 51=Recall to Network?
50
You have an external connection.
o Enter the service code and/or the phone number.
Step by Step
External call forwarding with a multiple subscriber number
If your communication system is connected to an ISDN
multiple device line, then you can forward all incoming
calls from the public network through your multiple subscriber number (MSN) to an external destination.
There are three types of forwarding:
• Calls are forwarded immediately (1=immediate call
forwarding).
• Calls are forwarded after a certain time (2=unanswered calls).
• Calls are only forwarded when the line is busy
(3=when busy).
Activating call forwarding to a "trunk"
Menu
><
Service?
><
Trunk FWD on?
o [ Enter and confirm your own multiple subscriber
number.
either:
><
1=immediate?
or:
><
2=on no answer?
or:
><
3=on busy?
continue:
o Enter the phone number of the destination (without external code).
Save
Save the settings.
51
Step by Step
Deactivating call forwarding to a "trunk"
Menu
><
Service?
><
Forward by Network
OFF?
o Follow the user guidance system from this point on-
wards (enter a multiple subscriber number or DID and
forwarding type).
[ Confirm your entries.
Using night service
In night service mode, for example during lunch breaks
or after office hours, all external calls are forwarded to a
particular internal telephone (night station) The night
station can be defined by the service engineer (= standard night service) or by you (= temporary night service).
When night service is active, the night station assumes
the function of the intercept station.
Activating night service
Menu
><
Night answer on?
either:
><
*=default?
"Standard night service" is configured.
or:
o Enter an internal phone number.
Save
Save the settings.
"Temporary night service" is configured.
52
Step by Step
Deactivating night service
Menu
><
Night Service - OFF?
Using dual-tone multifrequency
signalling
Your handset operates on the basis of digital information transmission. However, certain applications, e. g.
answering machines, can only be controlled using analog technology. For this you must send signals using the
dual-tone multifrequency signalling (DTMF) process.
Depending on how your system is configured (automatic tone dialling on or off - to be configured by the service
engineer) you must first switch to DTMF dialling. This
means, for example, that you can communicate with a
variety of voice storage systems.
You will find further details in the operating instructions
for the relevant applications.
Automatic tone dialling is not active
During a connection you must first switch to dual-tone
multifrequency signalling.
p
Menu
You are on a call.
><
Service?
><
* 53=Tone dialling?
o
Enter the numbers. All entries are sent as DTMF signals.
Automatic tone dialling is active
o
Enter the numbers. All entries are sent as DTMF signals.
53
Step by Step
Parking/activating calls
You can park up to ten calls (i.e. place them on hold) and
then reactivate them at other telephones in your communication system.
Parking a call
p
Menu
You are on a call you wish to park.
><
Service?
><
* 56=Park a call?
o Enter and note the parking position number (0... 9).
If the parking position number entered is already in use,
you must enter another one.
Picking up a specific parked call
Prerequisite:
One or more calls have been parked. Your handset is in
standby status.
Menu
><
Service?
><
#56=Retrieve call?
o Enter the parking position number you have noted.
Note:
If a parked call is not picked up, it returns to the
station from which it was parked after a certain
time (= recall). The following appears on the display "Recalling: (phone no. or name)" or "Recalling from (phone no. or name)".
54
Conducting calls – with multiple users
Step by Step
Conducting calls – with multiple
users
Call waiting
You need to speak to a user in your communication system urgently, even though his line is busy. You can send
a call waiting signal during his call to let him know you
want to talk to him. The user either answers immediately or you will be automatically connected to him when
he has finished his call.
This function is only available if it has been configured
by the service engineer.
The user is busy. You want to use call waiting.
p
Wait until the message "Camp-on" appears on the display (ringing tone).
You receive a call waiting signal (second call)
You are still available to other callers, even though you
are on the telephone. The call waiting signal informs you
of the second call while you are conducting a call. You
can answer this call without ending the first call.
p
You are on a call and hear a call waiting signal.
If you want to answer the second call, you can either
place the first call on hold (the first caller waits) or end
the first call.
Placing the first call on hold and answering the second call
2ndCall
Answer the second call.
Talk to the second caller. The first caller waits. His call is
on hold. You can now
• toggle between the two callers (Æ page 60) or
• set up a conference (Æ page 61).
55
Step by Step
Ending the second call
either:
Menu
><
Quit and return?
or:
a Press the On-hook key. The following message appears
on the display: "Recalling". Your handset rings.
c Press the Talk key to talk to the first caller again.
Ending the first call.
a Press the On-hook key. The first call is ended. Your
handset rings.
c Press the Talk key and answer the second call.
Call waiting tone off/on
You can suppress the call waiting tone for external calls.
Deactivating the call waiting tone
Menu
><
Waiting tone off?
Activating the call waiting tone
Menu
><
56
Waiting tone on?
Step by Step
Disabling/enabling automatic call
waiting
You can disable/ enable automatic call waiting signalling
for a second call during a telephone conversation.
Disabling the call waiting tone
Menu
><
Service?
><
Call wait. term. off?
Enabling the call waiting tone
Menu
><
Service?
><
Call wait. term. on?
Override
You need to speak to an internal user urgently, even
though his line is busy. The "Override" function allows
you to interrupt the ongoing call to pass on a message.
This function is only available when the code has been
input and if it has been configured by the service engineer.
p
The user is busy.
* 62 Call the function.
Override
o Enter the phone number of the busy user.
<Name>
The override is established. The user name or phone
number, to whom/which the call has been transferred,
is displayed.
57
Step by Step
Override is ended when you hang up the handset.
Note:
During override
• all users hear an override tone and everything that is said,
• all users see the following message on the
display "Override:....:".
Transferring calls
Transferring a call means that you wish to hand over a
call you are conducting on your handset to another user.
Transferring
(without announcing the transfer)
p
Menu
><
Start transfer?
You can use this function to forward a call which you answered to another user.
The current call is placed "on-hold", so that the first user
waits.
o Enter the phone number of the user to whom the call is
to be transferred.
p
The number is dialled.
either:
a Press the On-hook key. The target user’s phone rings.
He picks up the call by lifting the handset.
or:
Menu
><
Transfer?
You receive a recall
• immediately if you have made a mistake,
• 45 seconds after the transfer if the required user
does not answer.
If you do not answer recalls, another telephone defined
by the service engineer is called (intercept station).
58
Step by Step
Transferring
(with announcement of call transfer)
p
Menu
><
Start transfer?
You can use this function to forward a call which you
answered to another user.
The current call is placed "on-hold", so that the first user
waits.
o Enter the phone number of the user to whom the call is
to be transferred.
p
The number is dialled. The user answers. You announce
the call presently on hold.
either:
a Press the On-hook key. The user answers the call.
or:
Menu
><
Transfer?
59
Step by Step
Placing a call on hold
You can interrupt a call temporarily if, for example you
want to talk to someone else in the room. The line is
placed "on hold".
R or
p
Enquiry
You are on a call.
Press the R key or Display key. The current call is placed
"on hold", the user waits.
Resuming the call with the waiting user
either:
Menu
><
Quit and return?
You are reconnected to the partner.
or:
R
Press the R key.
Toggling
The Toggle function allows you to switch between two
users without allowing them to speak to each other directly. The two users can be either external or internal
users. You can also withdraw from the calls and connect
the two users with each other. You can also start a conference.
p
Menu
Callbck
You are on a call.
Press the Display key. The current call is placed "on
hold", the user waits.
o Enter the phone number of the second user.
p
Toggle
The second user answers.
Press the Display key to switch between the two calls.
When you end a call, the two users are connected with
each other (not possible when both users are external).
60
Step by Step
Conducting a conference
You can connect up to 5 internal or external partners
with each other in a telephone conference. You can include up to 4 external users in the conference.
For information purposes, you will hear a warning tone
every 30 seconds during a conference call (can be disabled - ask your service engineer).
Setting up a conference
You decide to set up a conference while talking to a
user.
p
Menu
><
Start conference?
You are on a call and wish to start a conference.
o Enter the phone number of the new user.
p
Menu
><
Conference?
The user is free and answers the phone. You announce
the conference.
You and your two partners are connected in a conference call.
Forming a conference
A conference has not yet been set up. However, you are
already connected to two users and are toggling between them. You now want to form a conference involving all partners.
p
Menu
><
Conference?
You are talking to one user.
You and your two partners are connected in a conference call.
61
Step by Step
Expanding a conference
You can expand an existing conference to include up to
five users.
p
Menu
><
Add party?
[ Select and confirm the menu item. Conference is
placed "on hold", the users wait.
o
p
Menu
><
You are connected with two or more partners in a conference call.
Conference?
Enter the phone number of the new user.
The user is free and answers the phone. You announce
the conference.
[ Select and confirm the menu item. The new user is included in the conference call.
Ending a conference
p
Menu
><
End conference?
[ Select and confirm the menu item. The conference is
ended.
Leaving a conference
a Press the On-hook key. You leave the conference.
When one user leaves the conference, the other two
users remain connected.
Viewing the names of conference parties
As the convener of the conference, you can view the
names of all conference parties.
p
62
Step by Step
Viewing the conference parties list
Mnu
><
View conf parties?
[ Select and confirm the menu item. The first party is displayed.
> View other parties.
Closing the conference party list
Mnu
><
Exit list?
[ Select and confirm the menu item. The conference party list is closed.
Disconnecting a party from the conference
As the convener of the conference, you can disconnect
users from the conference.
p
Menu
><
View conf parties?
> Display the required party.
Mnu
><
Remove party?
Select and confirm the menu item.
[ Select and confirm the menu item. The relevant party is
disconnected from the conference.
Connecting parties
p
Menu
><
Withdraw?
As the conference convener, you can leave the conference and thereby connect the other parties with each
other. If you were previously connected with two or
more parties, the other parties remain in a conference.
Otherwise, the remaining two users conduct a one-toone call.
a Press the On-hook key. You leave the conference; the
remaining parties are connected with each other.
63
Step by Step
Using the second call function
The second call is an incoming call that is signalled on
your handset during a call and that can be queried by
you.
A second call can be answered in the following call
states:
• You are on a single call,
• You are on an enquiry call,
• You are holding a conference,
• You are on a call which you intend to add to a conference,
• You are toggling between two partners.
64
Group functions
Step by Step
Group functions
Activating/deactivating group calls
If this has been configured by the service engineer, you
belong to one or more groups of users who can be
reached by means of a hunt group or group call phone
number.
Calls are signalled on all telephones in the group either
in succession (=hunt group) or simultaneously (=group
call), until a member of the group answers the call.
Every user in the group can also remain available under
his own phone number.
You belong to a hunt group or group call group
Menu
either:
><
Leave hunt group?
><
Join hunt group?
[ Select and confirm the menu item. The group call is deactivated.
or:
[ Select and confirm the menu item. The group call is activated.
continue:
65
Group functions
Step by Step
You are a member of several groups
Activating/deactivating individual groups
Menu
either:
><
Leave hunt group?
><
Join hunt group?
or:
continue:
>
Group 1
Group 2
Mnu
Select the required group and call the additional menu.
either:
><
Leave hunt group?
><
Join hunt group?
or:
continue:
Activating/deactivating all groups
Menu
either:
><
Leave hunt group?
><
Join hunt group?
or:
continue:
Group 1
Group 2
The list of groups is displayed.
# Press the hash key. The group call for all groups is activated.
or:
* Press the star key. The group call for all groups is deactivated.
continue:
66
Group functions
Step by Step
Ringing group on
You can have calls to your handset signalled acoustically
on up to five other telephones. The call is received by
the person who answers the call first.
Adding users to a group
First user
Menu
><
Service?
><
*81=Ringing group
on?
Mnu
Add ext to group?
[ Confirm.
o Enter the required internal phone number.
Save
Save the settings.
Other users:
Mnu
><
Add another ext?
o Enter the required internal phone number.
Save
Save the settings.
Deleting users
Menu
><
Service?
><
*81=Ringing group
on?
Mnu
67
Group functions
Step by Step
><
Display/Clear?
[ Select and confirm the menu item. The first user added
is displayed.
> Scroll to the required user.
Mnu
><
Delete?
[ Select and confirm the menu item. The addition of the
first user is cleared.
UCD (Universal Call Distribution)
This function enables calls to be distributed in a team.
An incoming call is always delivered to the team member who has been idle longest. Team members can also
work in separate rooms, e. g. on the company’s premises and at a teleworking station. The teams (call distribution groups) and team members are set up by the service engineer.
Logging on/off
You must log on and off at the system when you start/
finish work.
Logging on
Menu
><
Service?
><
UCD Menu?
><
*401=Log on?
o Enter your identifier number (assigned by the service
engineer).
Logging off
Menu
68
Group functions
Step by Step
><
Service?
><
UCD Menu?
><
#401=Log off?
Logging on/off temporarily
You can log on or off at the system temporarily, e.g. during break times.
Logging on
Menu
><
Service?
><
UCD Menu?
><
*402=Log on?
Logging off
Menu
><
Service?
><
UCD Menu?
><
#402=Not available?
Wrap-up time
If you need more time than the actual call lasts, you can
request/activate a wrap-up time for the last call. This
can be a fixed length of time or, alternatively, you must
deactivate the wrap-up time yourself (log back on).
69
Group functions
Step by Step
Requesting time
Menu
><
Service?
><
UCD Menu?
><
*403=Work on?
Logging back on
Menu
><
Service?
><
UCD Menu?
><
#403=Work off?
UCD night service
UCD night service is a separate night service for call distribution. It is not affected by the system night service.
All incoming calls are forwarded to a special call distribution destination.
Night destination on
Menu
><
Service?
><
UCD Menu?
><
*404=UCD night on?
70
Group functions
Step by Step
Night destination off
Menu
><
Service?
><
UCD Menu?
><
#404=UCD night off?
Checking the number of waiting calls
You can check the number of waiting calls for the group.
Menu
><
Service?
><
UCD Menu?
><
*405=Calls in
queue?
Mulap group (Multiple Line Application)
If your handset’s line belongs to a Mulap group (Multiple
Line Application), then you can
• answer calls for the group (press the Talk key in
group calls)
• make external telephone calls under the group
phone number (the group phone number is stored
in the called party’s caller list, for example )
• activate and deactivate the group call function for
your handset’s line
• forward the lines of the Mulap group to internal or
external destinations
71
Group functions
Step by Step
Activating/deactivating group calls
Menu
><
Service?
><
More features?
either:
><
#85=Leave hunt
group?
><
*85=Join hunt
group?
or:
continue:
Forwarding a Mulap line
You can immediately forward internal and/or external
calls to your lines to different internal or external telephones (destinations) (external destinations are also
possible if the system is configured accordingly).
If you activate call forwarding for a line, this shall apply
to all line keys of your group for this line.
Forwarding on
Menu
><
Service?
><
More features?
><
*501=Forward Line:
ON?
o Enter a line number.
either:
><
72
1=all calls?
Group functions
Step by Step
or:
><
2=external calls only?
or:
><
3=internal calls only?
o Enter the destination number.
Save
Save the settings.
Forwarding off
Menu
><
Service?
><
More features:
><
#501=Forward Line:
Off?
o Enter a line number.
73
Message functions
Step by Step
Message functions
The message functions enable you to react to voice
mail/ call back services of the communication system or
of other users or to initiate information features yourself.
Leaving a message/advisory message
A number of advisory messages are stored in your communication system that can be automatically sent to the
caller when an internal call is not answered (in the case
of handsets and telephones with display). These advisory messages can be selected and supplemented in
part by you:
0 = Will return at:
1 = On vacation until:
2 = I am out until:
3 = Out all day
4 = Out to lunch
5 = Not available
6 = Home phone:
7 = Contact:
8 = Avail at:
9 = Am in room:
These advisory messages are standard texts and may
have been changed in your communication system.
Activating an advisory message
Menu
><
Advisory msg. on?
either:
><
0 = Will return at:
1 = On vacation until:
[ Select the required advisory message.
If necessary Expand the message as necessary.
Save
Save the settings.
or:
><
74
Enter message text
Message functions
Step by Step
o Enter the required advisory message.
Typing errors cannot be corrected.
Note:
For example, if you want to enter the third character on a key: press the relevant key three times
in succession.
Save
Save the message.
continue:
Deactivating an advisory message
Menu
><
Absence Text OFF?
Sending/calling text messages
Messages can be sent internally to other handsets or
telephones with display. These text messages can be
selected and supplemented in part by you:
0 = Please callback
1 = Someone is waiting
2 = Appointment
3 = Urgent call
4 = Do not disturb
5 = FAX waiting
6 = Dictation please
7 = Please make copies
8 = Please make coffee
9 = Ready to depart
These text messages are standard texts and may have
been changed in your communication system.
75
Message functions
Step by Step
Send a text message
Menu
><
Send Message?
Message to:
o Enter the phone number for the required internal user.
either:
> < Please callback
[ Select the required advisory message.
Someone is waiting
or:
><
Enter message text
o Enter the required text message with the help of predictive text, if needed (Æ page 86).
Typing errors cannot be corrected.
Note:
For example if you want to enter the third character on a key: press the relevant key three times
in succession.
continue:
Send
Opening an incoming text message
J When your handset receives a text message, an advisory tone sounds and an advisory text is displayed. The
"Message List" icon is displayed.
The date and time of incoming text messages are
based on the communication system’s internal clock.
? Press the "message list" key.
Msg. from:
...
><
Text
Mnu
[ Select and confirm the menu item. The text message is
displayed.
76
Message functions
Step by Step
Answering a message or voice-mail
message
An advisory message appears when you have received
a message or voice mail.
You have new messages received J
Viewing a new message
either:
? Press the message key.
or:
Messages received
Menu
><
Display Messages?
> [ Select the required message and confirm your selection.
continue:
Msg. from:
Mnu
><
Text?
><
Time/date sent?
Mnu
[ Select and confirm the menu item. The time of the
message is displayed.
either:
Mnu
><
Call Sender?
[ Select and confirm the menu item. You call back the
sender.
or:
><
Delete?
[ Select and confirm the menu item. The entry is deleted.
continue:
77
Message functions
Step by Step
Check for a new voice-mail message
either:
? Press the message key.
or:
Messages received
Menu
><
Display Messages?
[ Select and display menu item.
o Follow the user guidance system from this point onwards.
Calling an old message
Old messages that have not been deleted cannot be
displayed using the message key ?. To call these messages, proceed as follows:
Messages received
Menu
><
>
Display Messages?
Msg. from:
...
><
Text?
><
<Text>
Time/date sent?
Mnu
Select the required message and call the additional
menu.
[ Select and confirm menu item.
Mnu
[ Select and confirm the menu item. The time of the
message is displayed.
><
at: ...
Mnu
either:
><
78
Call Sender?
[ Select and confirm the menu item. The sender is called
back.
Message functions
Step by Step
or:
><
Delete?
[ Select and confirm the menu item. The entry is deleted.
continue:
Caller list
If you are unable to answer an external and/or internal
call, this call request is stored in a caller list. If you belong to a hunt group or group call group, these call requests are also stored.
Your handset can store up to 10 calls in chronological order. Every call is given a timestamp. The display starts
with the latest call request still not called. When several
calls are received from one caller, the number of calls is
shown.
During a call, you can save the other caller’s phone
number to your caller list.
Note:
If the service engineer has made the appropriate configuration, the phone numbers for all external answered calls are automatically saved.
Selecting a call request
Menu
><
Caller list?
[ Select and confirm the menu item. The first call request
is displayed.
> Select a call request.
79
Message functions
Step by Step
Calling back a caller
Mnu
><
Call?
Call the menu.
[ Select and confirm the menu item. The connection is
set up.
Note:
If a connection is established, the user is automatically deleted from the caller list. Call requests for groups (hunt group/group call) are
also deleted if a member of the group has set up
the connection.
If the "Save number?" option is not displayed, all
external incoming calls are automatically saved.
Adding a caller to the caller list
During a call, you can save the other party’s phone
number in your caller list, e.g. to remind you to call again
later.
Menu
><
Save number?
[ Select and confirm the menu item. The caller’s phone
number is saved.
Deleting a caller from the caller list
Menu
><
Missed Call List?
[ Select and confirm the menu item. The first call request
is displayed.
> Select a call request.
Mnu
><
80
Delete?
Call the menu.
[ Select and confirm the menu item. The call is deleted.
Additional functions
Step by Step
Handset alarm clock function
When the alarm clock is activated, it rings every day at
the set time. The alarm clock is deactivated during automatic number redial.
Note:
Please note the following:
• First set the date and time. This sets the internal clock of the handset.
• Do not switch off the handset after you have
made the settings, otherwise the date and
time will be reset. The alarm clock would otherwise relate to an incorrect time setting.
• Check the date and time and reset from time
to time where applicable.
Activating the alarm clock
The handset is in idle status.
© Open the menu.
DE
Calendar/Clock
DE
Alarm Clock
Save
Save the settings.
¼ The alarm clock is activated.
Deactivating the alarm clock
An appointment reminder call is signalled in the same
way as an incoming call.
o Press any key during an alarm call.
81
Step by Step
Deactivating the alarm clock
© Open the menu.
DE
Calendar/Clock
DE
Alarm Clock
F Off G Fix the setting.
Save
Save setting.
Handset appointment reminder
function
You can arrange your handset to remind you up to five
appointments. The handset must be in idle status at the
time of the appointment reminder. The appointment reminder function is deactivated during automatic
number redial.
Note:
Please note the following:
• First set the date and time. This sets the internal clock of the handset.
• Do not switch off the handset after you have
made the settings, otherwise the date and
time will be reset. The appointment reminder
function would otherwise be based on an incorrect time setting.
• Check the date and time and reset from time
to time where applicable.
82
Step by Step
Activating the appointment reminder function
DE
Calendar/Clock
DE
Set Appoints.
© Open the menu.
D E [ Select and confirm the required appointment.
o Enter the date, e. g. 11 November = 1111.
F G Specify the text.
Save
Save the settings.
¼ The appointment reminder function is activated.
Confirming an appointment reminder call
An appointment reminder call is signalled in the same
way as an incoming call.
o Press any key during the appointment reminder call.
If you do not confirm the appointment reminder call, it
will be stored in a missed dates list.
83
Step by Step
Deactivating the appointment reminder function
DE
Calendar/Clock
DE
Set Appoints.
© Open the menu.
F OFF G Fix the setting.
Save
Save setting.
Displaying an unconfirmed appointment
If you have failed to confirm an appointment reminder
call, a Display key is assigned the "Missed Appoint."
function. This unconfirmed appointment must also be
saved in a missed dates list.
Missed Appoint.
Display an appointment.
[ Open an appointment. The date and time of the unconfirmed appointment are displayed.
Displaying an unconfirmed appointment and unconfirmed anniversaries
Any appointment reminder calls and anniversary calls
you fail to confirm are stored in a missed dates list.
© Open the menu.
DE
Calendar/Clock
DE
Missed Dates
F G [ Select the unconfirmed appointment or an unconfirmed
anniversary. The relevant information is displayed.
84
Step by Step
System appointment function
You can use your handset to enter a single appointment
for the next 24 hours or an appointment that recurs on
a daily basis.
When the appointment is due, your handset rings for
approx. 20 seconds to remind you of your appointment.
The entered appointment appears on the display. This
appointment call is deleted when you confirm it. Alternatively it is deleted automatically after it has been repeated 5 times at one minute intervals.
(Æ page 92).
Entering an appointment
Menu
><
Service?
><
*46=Timed reminder
on?
Remind at (HHMM):
o Enter the required time.
Note the required data format: Appointment at (HHMM); HH = two-digit hour setting mm = minutes, two
digits For example: 0905 for 9.05 (= 9.05 a.m.) or 1430
for 14.30 (= 2.30 p.m).
either:
><
One time only?
[ Select a menu item.
or:
><
Daily?
continue:
Save
Save the settings.
Deleting/ checking entered appointments
Menu
85
Step by Step
><
Service?
><
#46=Timed reminder
off?
Reminder at...
Mnu
either:
><
Delete?
or:
><
End?
Confirming an appointment
The handset rings and the appointment is displayed.
a Press the On-hook key. The appointment is confirmed.
Using predictive text
Predictive text helps you in writing the following texts:
• Names in the telephone directory
• Names in the speed dialling list
• Names in the e-mail directory
Each key between "0" and "9" is allocated multiple letters and characters which are shown in a selection line
directly over the Display keys when a key is pressed.
When you enter letters, the most likely choice will be
highlighted with black. This letter will be placed at the
beginning of the selection line and in the text field.
If this is the required letter, confirm it by pressing the
next key. If this is not the required letter, press the hash
key until the correct letter is highlighted with black in
the display line and appears in the text field.
DE
D or C Select required menu.
New Entry
When entering a name:
© Open menu.
86
Step by Step
DE
Predictive Text
Predictive text is activated.
a Press the On-hook key to return to the text field.
o Enter text.
# Press function key to select a character. Then press the
next letter.
DE
© Open menu.
[ Save settings.
Save
Selecting a base
If your handset is registered at multiple bases, then you
can set a specific base or the base with the best reception as the base to be used. The handset then switches
automatically to this base.
You can change the base name that is displayed on the
handset at any time (Æ page 27).
DE
H/Set Settings
DE
Select Base
DE
Base 1
Best Base
[ Select the required base and confirm. The selected
base is ticked.
87
Telephone blocking
Step by Step
Telephone blocking
Handset telephone lock
You can protect your handset against unauthorised access by entering a 4-digit numerical code to lock it.
The PIN is preset to "0000" (default). The handset does
not prompt for a PIN in this setting. As soon as you have
changed the PIN you will need to enter it when you turn
on the handset.
Enter the value "0000" again to deactivate the PIN.
Attention:
If you have forgotten your PIN, please contact
Siemens Service. The PIN will be reset at your
own expense.
Entering a new PIN
G Open the main menu of the handset.
DE
H/Set Settings
DE
Change HSPIN
o
Enter the old PIN.
o
Enter the new PIN.
o
Repeat the new PIN.
[ Confirm your entry.
Battery charging when PIN lock active
If you turn off the handset when the PIN lock is active
and place it in the charging shell, the handset turns itself
back on and prompts for the PIN.
However, incoming calls will not be answered due to
the lock.
88
Telephone blocking
Step by Step
Telephone lock code programming
You can protect your handset against unauthorised access (thereby safeguarding personal data) by entering a
5-digit code to lock and unlock it.
To change a code, first enter the old code and then key
in the new code twice.
Menu
><
Service?
><
*Change PIN?
o Enter the old PIN (5 digits, default "00000").
o Enter the new PIN, e.g. 11111 (5 digits).
o Repeat the new PIN.
Note:
If you have forgotten your PIN, contact your
service engineer for help. He will be able to reset your PIN to "00000".
It is also possible to open your mobile phone
from a central station, e.g. from the attendant
terminal.
89
Telephone blocking
Step by Step
Locking/unlocking the handset
You can lock your handset to prevent external dialling
and programming, thereby preventing unauthorised
use in your absence, for example.
Prerequisite: You have defined a personal code or use
the default code "00000".
Locking the handset
Menu
><
Changeover on?
o Enter the PIN code (5 digits, default "00000").
Note:
Even though it is locked, you can still use your
handset to answer external calls and make internal calls. When an external connection is established, the following message appears on the
display "Telephone Lock Active".
Your handset can also be locked from a central
station (Æ page 91).
Unlocking the handset
Menu
><
Changeover off?
o
Enter the PIN code (5 digits, default "00000").
90
Telephone blocking
Step by Step
Central telephone lock/locking/unlocking other handsets
If you have the appropriate authorisation, you can lock
and unlock other handsets to prevent unauthorised use.
If the user has locked his handset and has forgotten the
individual password he has set, you can unlock the
phone again using this function.
Menu
><
Service?
><
More features?
><
*943=Telephone
Lock?
o Enter a user’s phone number.
either:
* Lock the handset. The following appears on the display:
"Telephone locked".
or:
# Unlock the handset. The following appears on the display: "Telephone unlocked".
91
System functions
Step by Step
System functions
The system functions can be called up via the menu or
directly by entering codes.
Calling functions via the menu
Menu
either:
><
Suppress call ID?
[ Select and confirm the function.
><
Service?
><
*41=Temporary
MNS?
or:
or:
><
Service?
><
More functions?
><
#58=View callbacks?
continue:
Calling functions via codes
either:
*o Enter code according to table (Æ page 92).
or:
#o Enter code according to table (Æ page 92).
continue:
92
System functions
Functions and codes
Functions
Codes
Automatic call wait.term.on
* 490
Automatic call wait.trm.off
Waiting tone off
Waiting tone on
Call waiting
# 490
* 87
# 87
* 55
Caller list
- Call
- Save phone number
Advisory msg. on
Advisory msg. off
DND on
DND off
# 82
* 82
* 69
# 69
* 97
# 97
UCD:
- Log on
- Log off
- Work on
- Work off
- Available
- Not available
- UCD night on
- UCD night off
- No. of calls
Override (authorised telephone only)
Call trace
* 401
# 401
* 403
# 403
* 402
# 402
* 404
# 404
* 405
* 62
* 84
Messages
- Send
- View sent message
* 68
# 68
93
System functions
Functions
Codes
Conference:
- On
- Off
Call Charge Display
Use speed dialing
Change Speed Dial
Toggle
Tone dialling
Night Service ON
Night Service OFF
*3
#3
* 65
*7
* 92
*2
* 53
* 44
# 44
Park
- Park call
- Retrieve call
Account code
Callback
View callbacks
Suppress phone number
Temporary phone number (MSN)
Restore phone number
Ringing group on
Hunt group on
Hunt group off
Control Relay On
Control Relay Off
Change PIN
Recall to Network (flash)
Changeover on
Changeover off
Tel. data service
94
* 56
# 56
* 60
* 58
# 58
* 86
* 41
# 86
* 81
* 85
# 85
* 90
# 90
* 93
* 51
* 66
# 66
* 42
System functions
Functions
Codes
Timed reminder on
* 46
Timed reminder off
Door release ON
Door release OFF
Door opener
Pickup group
Pickup, directed
Forwarding on
Forwarding off
Trunk FWD on
Trunk FWD off
Telephone Lock
Return to held call
# 46
* 89
# 89
* 61
* 57
* 59
*1
#1
* 64
# 64
* 943
*0
95
Appendix
Appendix
Troubleshooting
Some malfunctions can be resolved without outside intervention. The following table provides a list of such malfunctions.
Error
Possible cause
Remedy
No display.
Handset not switched
on.
Press the On-hook key
until confirmation is received.
Battery is empty.
Charge or replace the
battery.
No reaction to keystroke. Keypad lock activated.
Press the hash key until
confirmation is received.
De-crescendo tone sequence during input.
Repeat key sequence
while watching the display; where applicable,
consult the operating instructions.
An incorrect entry was
made.
The line "Base n" flashes The handset is outside Come closer to the base
(n= 1 - 4).
the base radio range; Ra- radio range, change your
dio signals too weak.
position.
Handset not registered. Register the handset.
No ringer on the handset.
Intervals between synchronisation attempts
are too long.
Switch off the handset
and switch it back on
again.
Ringer is deactivated.
Activate ringer.
Nothing audible during a The "R key" was pressed
call.
– the microphone and
the receiver inset are
muted.
The following appears
immediately after the
Talk key is pressed:
Press the "Delete" Display key to re-activate
the microphone and the
receiver inset.
Communication system Repeat call later.
is being used by other
users.
Connect.
No dial tone available; No
calls can be made.
The following, for exam- Handset is blocked.
ple, appears:
Base 1
Outgoing and incoming
calls and activation/deactivation are not possible.
96
Remove the battery from
the handset and then reinsert it. Procede as
when loading batteries
for first time.
(Æ page 14).
Appendix
Cleaning the handset
To clean the handset and the charging shell, simply wipe them with a damp
or antistatic cloth. Never use a dry cloth.
Do not use abrasive cleaning agents.
Technical data and accessories
Gigaset S1
professional
Gigaset SL 1
professional
Maximum sound
pressure level as
per TBR10, Annex D
118 dB (A)
118 dB (A)
Hours of use with
fully charged battery
Standby: 170 h
Talktime: 13 h
Charging time: 5 h
Standby: 250 h
Talktime: 15 h
Charging time: 2 h
Permissible
ambient conditions
for operation
+5 °C to +45 °C
20 % to 75 % relative
humidity
+5 °C to +45 °C
20 % to 75 % relative
humidity
Weight incl. batteries
approx. 148 g
approx. 140 g
Dimensions
(L x W x H)
approx.
146 x 55 x 27 mm
approx.
114 x 47 x 22 mm
Order number
charging shell EU
incl. plug-in mains unit
S30852-H1502-R141
EU
incl. power supply unit
S30852-H1521-R147
EU
Order number
charging shell
United Kingdom
S30852-H1502-V141
UK
incl. power supply unit
S30852-H1521-V147
UK
Order number
plug-in mains unit
EU
S30852-H1502-R141
EU
Order number
plug-in mains unit
United Kingdom
S30852-H1502-V141
UK
97
Appendix
EU-guidelines
89/336/EC "Electromagnetic Compatibility"
73/23/EC "Electrical apparatus for use within
specific voltage parameters"
Declaration of conformity
Your handset is supplied for use within a specific country, which is displayed on the underside of the device. Country-specific features must be
observed.
The device complies with the basic requirements of the R&TTE Directive
and therefore displays the CE symbol.
Extract from original declaration
"We, Siemens AG, declare, that the above mentioned product is manufactured according to our Full Quality Assurance System certified by CETECOM ICT Services GmbH with the registration number "Q810820M" in
compliance with ANNEX V of the R&TTE-Directive 99/05/EC. The presumption of conformity with the essential requirements regarding Council
Directive 99/05/EC is ensured."
Senior Approvals Manager
The Declaration of Conformity (DoC) has been signed. In case of need, a
copy of the original DoC can be made available via the company hotline.
98
Index
Index
A
Activating ....................................................... 2
Advisory message ..................................... 74
Advisory tones ............................................ 21
Anniversary function ................................. 38
Anonymous calling .................................... 43
Answering a message .............................. 77
Answering calls .......................................... 44
Answering voice mail ................................ 77
Attachment clip ............................................. I
Fitting ....................................................... 16
Auto. Answer .............................................. 26
Automatic call waiting ............................... 57
B
Batteries
Approved batteries ................................ 15
Capacity ................................................... 15
Charging ................................................... 14
Compartment cover .................................. I
Inserting ................................................... 13
Operating time ....................................... 15
Permitted ~ ............................................. 15
Warning tone .......................................... 28
Battery pack ................................................ 15
Battery tone
Function ................................................... 28
Set ............................................................ 21
C
Call answering .............................................. 6
Call answering group ................................... 7
Call charge display ..................................... 45
Call charges ................................................. 45
Call forwarding ............................................. 7
Call forwarding to a fixed destination ....... 7
Call pickup group ......................................... 7
Call trace ...................................................... 46
Call waiting .................................................. 55
Automatic ~ ............................................ 57
Call waiting tone off/on ............................. 56
Callback ......................................................... 4
Callback key ................................................ 10
Caller list ...................................................... 79
Calls
Directed transfer .................................... 44
Making ....................................................... 3
Picking up .................................................. 7
Rejecting .................................................... 6
Capacity ....................................................... 15
Carrier list .................................................... 38
Charge status ............................................. 14
Charging and using the batteries ............ 14
Charging time ............................................. 15
Cleaning ....................................................... 97
Conference .................................................. 61
Connecting parties ................................. 63
Disconnecting ......................................... 63
Ending ...................................................... 62
Expanding ................................................ 62
Leaving ..................................................... 62
Setting up ................................................ 61
Viewing .................................................... 62
Confirmation tone
Function ................................................... 28
Set ............................................................ 21
Connecting parties ..................................... 63
Connection quality ....................................... 2
Control key ...........................................I, II, 11
Control relay ................................................ 49
D
Data cable .................................................... 30
Data transfer ............................................... 30
Date, setting ............................................... 26
Deactivating .................................................. 2
Default state ............................................... 28
Delete .......................................................... 12
Dialling
After line seizure ...................................... 3
Before line seizure ................................... 3
Preparation ................................................ 3
Directed answering of calls ...................... 44
Directed assignment of an MSN ............. 41
Directed transfer of calls .......................... 44
Display ........................................................ I, II
99
Index
Display keys ......................................... I, II, 12
Do not disturb ............................................. 45
Door release
Activating ................................................. 48
Deactivating ............................................ 48
E
E-mail directory .......................................... 40
Enquiry (second line) ................................... 5
Entering codes ........................................... 92
Entrance telephone ................................... 47
External call forwarding ............................ 51
F
Function keys ............................................. 10
Functions and codes ................................. 93
G
Group call
Activating/deactivating .......................... 65
Group functions ......................................... 65
H
Handset
Locking/unlocking the telephone ........ 90
Handset operating times .......................... 15
Handset telephone directory ................... 38
Handset volume ......................................... 18
Hash key ............................................... I, II, 10
Hunt group .................................................. 65
I
Identification code ..................................... 42
Idle display, editing .................................... 27
Individual system speed dialling ............. 36
Inserting the batteries ............................... 13
Interface ...................................................... 30
Interference with electronic equipment
EMC ........................................................... II
K
Key tones
Function ................................................... 28
100
Set ............................................................ 21
Keypad lock ................................................... 9
Keys
Control key .............................................. 11
Display keys ............................................ 12
Function keys .......................................... 10
L
Leaving a message .................................... 74
Leaving the radio network/re-registering . 9
Line seizure ................................................... 3
M
Mailbox function ........................................ 74
Making calls .................................................. 3
Message functions .................................... 74
Message list ........................................ I, II, 10
Messages .............................................. 74, 75
Microphone ................................................ I, II
MSN ....................................................... 41, 51
Mulap group
Activating call forwarding ..................... 72
Deactivating call forwarding ................. 73
Deactivating/ activating group calls ..... 72
Forwarding a line .................................... 72
Multiple subscriber number ............... 41, 51
N
NET key ....................................................... 10
Night service ............................................... 52
Number redial ............................................. 34
Deleting an entry .............................. 35, 40
List ........................................................ 3, 34
Manual ....................................................... 3
Transferring a phone number .............. 35
O
On hold ........................................................ 60
On/Off key ..................................................... II
On/off key ................................................ I, 10
On-hook key ......................................... I, II, 10
Opening/closing battery compartment .. 13
Operating and charging times ................. 15
Override ....................................................... 57
Index
P
Parking ......................................................... 54
Parts of the device ........................................ I
PC interface ................................................ 30
Permitted batteries .................................... 15
Picking up a call ............................................ 7
Placing a call on hold ................................. 60
Playing a melody ........................................ 23
Project code ................................................ 42
Protective cover ......................................... 13
R
R key ...............................................I, II, 10, 11
Radio range ................................................... 2
Range problems ........................................... 2
Recall ...................................................... 54, 58
Receiver inset ............................................ I, II
Recording a melody ................................... 23
Reject call ...................................................... 6
Rejecting a call ............................................. 6
Reset ............................................................ 28
Ringer echo ................................................. 22
Ringer loudspeaker ....................................... I
Ringing ......................................................... 19
Ringing group on ........................................ 67
System speed dialling ............................... 36
System telephone directory ..................... 37
T
Talk key .................................................I, II, 10
Talk time ...................................................... 15
TDS telephone data service ..................... 49
Technical data ............................................. 97
Telephone blocking .................................... 89
Telephone conference .............................. 61
Telephone lock ........................................... 91
Temporary phone ....................................... 43
Time control ................................................ 20
Time, setting ............................................... 26
Toggling ....................................................... 60
Tone dialling ................................................ 53
Tones .....................................................19, 21
Transfer ........................................................ 58
Troubleshooting ......................................... 96
U
UCD night service ...................................... 70
Universal call distribution .......................... 68
V
S
Second call .................................................. 64
Second line ................................................. 43
Second line (enquiry) ................................... 5
Selecting a base ......................................... 87
Sending a signal to the network .............. 50
Setting the language ................................. 26
Handset ................................................... 16
Setting the ringer ....................................... 19
Silent alert ................................................... 22
Sound Manager .......................................... 23
Sound setting functions ............................ 18
Speakerphone key .............................. I, II, 10
Speakerphone mode ................................. 31
Speed dial key .............................................. II
Speed dialling ....................................... 36, 38
Speed dialling key ......................................... I
Standby mode ............................................ 15
Star key ................................................. I, II, 10
Suppress phone number .......................... 43
Voice dialling ............................................... 32
W
Warning tone ........................................25, 61
Wrap-up time .............................................. 69
101
www.siemens.com/hipath
This device has been manufactured in accordance with our certified environmental management system (ISO 14001). This process
minimises energy consumption, the use of primary raw materials and waste production.
© Siemens AG 2003
Information and Communication Networks
Hofmannstr. 51 • D-81359 München
Order no.: A31003-G1531-B800-2-7619
The information in this document contains only general descriptions
and features that may not always apply as described in specific cases or
that may change as a result of the further development of the products.
The required features are only binding if they are expressly agreed
when the contract is signed.
Subject to availability and technical changes.
Printed in Federal Republic of Germany
14.09.2005

HiPath 500 HiPath 3000 Gigaset SL1 professional Gigaset S1

Transcription

Similar documents

July, 1993 - Stumpf Welding Supplies

Setting an Android Device to AutoFill Password Fields in

brightsign xd smart menu board

Published in Western Horseman - July, 2001

Customize Your Profile - Division of Student Affairs

Happy Hour Menu - Toulouse Petit

View our Events Brochure

Tektronix TDS 210 Quick Start

Registering Dect Handset On Siemens Hipath

TALLULA PRIVATE EVENTS | FREQUENTLY ASKED QUESTIONS