Century Hughes 500D 60

Transcription

HUGHES 500D
GENERAL INSTALLATION MANUAL
B
1
GLUE 6 PCS.
OF 3x10x10 MM
PLYWOOD AT A.
B
2
ENGINE SIZE:60
NOTICE: USE EPOXY UNLESS STATED.
SAND INSIDE FUSELAGE WITH #180 SANDING
PAPER BEFORE PARTS GLUING IN PLACE.
C
C
C
C
A
A
A
A
A
B
A
B
GLUE 4 PCS. OF
3x10x16 MM PLYWOOD AND DRILL 3 MM HOLES AT B.
3
D
D
GLUE 4 PCS. OF 3x10x16 MM PLYWOOD AT C.
AND DRILL 3 MM HOLES AND INSTALL 3 MM ALUM. POLES
AT C FOR FRONT AND REAR ALIGNMENT.
(LOCATION OF C MUST BE MATCHED WITH B IN STEP 1.)
4
D
D
D
D
FASTEN FRONT AND REAR
PORTION OF FUSELAGE
WITH 6 PCS. OF 3 X 6 MM
ROUND HEAD TAPPING
SCREWS AT D
DRILL 3 MM HOLES AT D.
(LOCATION OF D MUST BE MATCHED WITH A IN STEP 1.)
5
6
GLUE RED LIGHT, ALUM. LIGHT HOLDER
ON TOP OF FUSELAGE
8 MM
GLUE EXHAUST TUBE TO FUSELAGE
8
7
GLUE RED LIGHT, ALUM. LIGHT HOLDER
ON BOTTOM OF FUSELAGE
GLUE CLEAR PLASTIC LEN
P.1
HUGHES 500D
ENGINE SIZE:60
9
10
GLUE RED LIGHT
ON TAIL FIN
GLUE 2.5 MM TAIL SKID
WIRE IN THE TAIL FIN
11
12
GLUE HORIZONTAL STAB.
IN MAIN VERTICAL FIN
GLUE AND FASTEN VERTICAL FIN IN HORIZONTAL
STAB. WITH 2 X 8 MM TAPPING SCREW
13
14
GLUE ROUND HEAD ROD ENDS IN
THE FRONT OF LANDING GEAR
15
GLUE FLAT HEAD ROD ENDS IN
THE REAR OF LANDING GEAR
16
FASTEN PLASTIC LANDING GEAR
WITH 3 X 12 MM SOCKET HEAD
TAPPING SCREWS
FASTEN LANDING GEAR WITH 3 X4 MM SET SCREWS
P.2
HUGHES 500D
ENGINE SIZE:60
17
18
CONNECT SILICONE TUBE FROM ENGINE MUFFLER
TO EXHAUST TUBE
PUT A SMALLER SILICONE TUBE ON THE MUFFLER
AND THEN INSERT SILICONE TUBE. FASTEN SILICONE
TUBE WITH CABLE TIE.
20
19
PRESS AND GLUE 3 MM ALUM.
BLIND NUTS IN PLYWOOD
21
SELECT THE MOUNTING HOLES FOR YOUR
MECHANISM FROM MOUNTING HOLES TEMPLATE.
ENLARGE THE REQUIRED MOUNTING HOLES TO
4.5 MM. GLUE THE BLIND NUT PLYWOOD IN STEP
19 TO THE HOLES UNDER MECHANISM PLATFORM.
22
FASTEN MECHANISM WITH SOCKET
HEAD SCREWS
INSERT TAIL BOOM INTO SPONGE RING
23
FASTEN ALUM. MOUNTING
PLATE WITH 3 X 10 MM
SOCKET HEAD SCREWS,
WASHERS AND
LOCK-NUTS
24
CUT WINDSHIELD AND WINDOWS AS MARKED.
GLUE IN PLACE WITH SILICONE OR "GOOP" *.
* "GOOP" IS A BRAND OF GLUE WHICH IS MANUFACTURED BY
ECLECTIC PRODUCTS, INC.
IT IS AVAILABLE IN MOST HARDWARE STORES.
P.3
HUGHES 500D
ENGINE SIZE:60
MECHANISM MOUNTING HOLES TEMPLATE
HIROBO FREYA
THUNDER TIGER
RA PTOR
CENTURY
PREDATOR
CENTURY
PREDATOR
THUNDER TIGER
RA PTOR
HIROBO FREYA
P.4
HUGHES 500D
ENGINE SIZE:60
MOUNTING HOLES FOR MAIN VERTICAL FIN TEMPLATE
CENTURY
PREDATOR
HIROBO
FREYA
THUNDER TIGER
RA PTOR
P.5
HUGHES 500D
ENGINE SIZE:60
INSTALLATION OF CENTURY PREDATOR MECHANISM
2
1
HOLE FOR STARTING PROBE
INSTALL ALUM. MOUNTING
PLATE AS SHOWN.
3
4
PLACE 2MM THICKNESS
ALUM. WASHER
IN-BETWEEN THE
2 REAR HOLES OF
MECHANISM AND
FUSELAGE.
PLACE 2MM THICKNESS ALUM. WASHER IN-BETWEEN
THE 2 REAR HOLES OF MECHANISM AND FUSELAGE.
5
6
FASTEN ALUM.
MOUNTING PLATE
WITH 3 X 10 MM
SOCKET HEAD
SCREWS, WASHERS
AND LOCK-NUTS
CUT VENTILATING HOLE AS SHOWN
7
SELECT THE APPROPRIATE HOLES FROM MOUNTING
HOLES FOR MAIN VERTICAL FIN TEMPLATE.
DRILL 6 MM HOLES AND GLUE ALUM. INSERTS OF
11 MM LENGTH.
8
MOUNT THE VERTICAL FIN WITH 3 X 35 MM SCREWS,
3 X 10 X 1.5 ALUM. WASHERS AND 3MM LOCK-NUTS.
P.6
HUGHES 500D
ENGINE SIZE:60
INSTALLATION OF HIROBO FREYA MECHANISM
2
1
SHORTEN FUSELAGE
TAIL BOOM BY 20 MM
3
4
SOCKET HEAD SCREWS
AND LOCK-NUTS.
5
FASTEN MECHANISM WITH
SOCKET HEAD SCREWS
6
SOCKET HEAD SCREWS
WASHERS AND
LOCK-NUTS
7
15 MM LENGTH.
8
P.7
HUGHES 500D
ENGINE SIZE:60
INSTALLATION OF THUNDER TIGER RAPTOR MECHANISM
2
1
SHORTEN FUSELAGE
TAIL BOOM BY 4 MM
3
INSTALL ALUM. MOUNTING
PLATE AS SHOWN.
5
4
PLACE 2MM THICKNESS ALUM. WASHER IN-BETWEEN
THE 2 FRONT HOLES OF MECHANISM AND FUSELAGE.
6
SOCKET HEAD SCREWS
WASHERS AND LOCK-NUTS
7
11 MM LENGTH.
8
P.8

Century Hughes 500D 60

Transcription

Similar documents