SAKUNDIAK - Shortline Ag, Inc.

Transcription

SAKUNDIAK
ASSEMBLY INSTRUCTIONS
OPERATOR'S MANUAL
PARTS LIST
SLMD12 MECHANICAL DRIVE AUGER
MODEL NO.
SLMD12-2200
SLMD12-2400
SLMD12-2600
OPERATORS MANUAL SLMD12 SERIES
TABLE OF CONTENTS
GENERAL
1
2
3
Table Of Contents
Sign Off Sheet
General Safety
SAFETY
4
5
6
7
Machine Inspection
Designated Work Area
Safety Guard Description
Transport And Placement
OPERATIONS
8
9
10
Start Up And Break In
Lubrication And Maintenance
Safety Decals And Location
ASSEMBLY
13
14
16
17
18
19
20
21
22
Set Up Procedure
Tube And Truss Assembly
Winch Assembly
Hitch Assembly
Top Lift Frame Assembly
Frame Assembly
Lift Arm Assembly
Feed Tube Assembly
Hopper Assembly
PARTS
23
24
25
26
28
29
30
31
32
34
36
38
40
41
Main Frame Assembly
A-Frame Assembly
PTO Shaft Assembly
Hopper Assembly
Feed Auger Head and Tube Assembly
Lift Arm Assembly
Top Gear Box Assembly
Bottom Gear Box Assembly
Boot Assembly
Tube Assembly- 2200
Tube Assembly- 2400 & 2600
Truss Assembly
Winch Assembly
Bolt On Winch Plate Assembly
INDEX
42
Parts Index
WARRANTY
43
Warranty and Disclaimer
SAKUNDIAK GRAIN AUGER SIGN OFF SHEET
As a requirement of OSHA, it is necessary for the employer to train the employee in the safe operation and safety
procedures with this auger. We include this sign-off sheet for your convenience and personal record keeping.
DATE
EMPLOYER SIGNATURE
EMPLOYEE SIGNATURE
GENERAL SAFETY
Watch this symbol. It points out important precautions.
It means "ATTENTION - BECOME ALERT!
YOUR SAFETY IS INVOLVED"
Occupational safety is of prime concern to Sakundiak Equipment Ltd. This transport manual was written
with the safety of the operator and others who come in contact with the equipment as our prime concern.
This manual presents some of the day to day work problems encountered by the operator and other
personnel. We wrote this manual to help you understand safe operating procedures for augers. We want
you as a partner in the safe operation of our equipment.
It is your responsibility as an owner, operator, or supervisor, to know what specific requirements, precautions
and work hazards exist and to make these known to all other personnel working with the equipment or in
the area so that they too may take any necessary precautions that may be required.
Failure to read this Transport Auger Manual and it's Safety
Instructions is a misuse of the equipment.
SAFETY ALERT SYMBOLS
BE ALERT
This symbol is used to call your attention to instructions concerning your personal safety. Watch for this
symbol - it points out important safety precautions. It means "ATTENTION - Become Alert! Your Safety Is
Involved!" Read the message that follows and be alert to the possibility of personal injury or death.
MACHINE INSPECTION
•
Check to see that all guards listed in the assembly instructions are in place, secured and functional.
•
Check winch and cable for security and operation. There should be at least 3 complete wraps of cable around
winch drum in full down position. Cable anchor on winch drum must be tight.
•
Are all fasteners tight?
•
Are all chains properly adjusted? (See Maintenance Section)
•
Check oil levels in gear box. (See Maintenance Section)
OPERATOR QUALIFICATIONS
Operation of this transport auger shall be limited to competent and experienced persons. In addition, anyone who
will operate or work around a portable auger must use common sense. In order to be qualified, they must know and
meet all other requirements, such as:
•
Some regulations specify that no one under the age of 16 may operate power machinery. This includes augers
and flight type elevators. It is your responsibility to know what these regulations are in your area or situation.
•
Current OSHA regulations state in part: "At the time of initial assignment and at least annually thereafter, the
employer will instruct every employee in the safe operation and servicing of all equipment with which the
employee is, or will be involved.
•
Unqualified persons are to stay out of the work areas.
•
A person who has not read and understood all the operating and safety instructions is not qualified to operate
the machine.
DESIGNATED WORK AREA
The following diagrams will show the designated work areas. These areas shall be marked off with colored nylon or
plastic rope hung by portable barriers to define the designated work areas.
Under no circumstances should persons not involved in the operation of the equipment be allowed to trespass into
the work area.
It shall be the duty of all operators to see that children and or other persons stay out of the work area. Trespass
into the area by anyone not involved in the actual operation, or trespass into a hazard area by anyone shall result in
an immediate shut down by the operator.
Prior to start up and during operation, it shall be the responsibility of the operators to see that the work area has
secure footing, is clean and free from all debris and tools which may cause accidental tripping and/or falling.
CAUTION!
WALKING SURFACE,
. . IS IT SLIPPERY?
ARE THERE THINGS TO TRIP YOU?
A
-------
----
A
KEEPAWAY!
..
OVERHEADW_I_R-ES-~
A
HAZARD, KEEP OUT!
UNDER AUGER AND
UNDERCARRIAGE AREA .
-----------------------------~
\
i
A
HAZARD, KEEP OUT,
. . AUGER INTAKE AREA.
•...................... . WHEELCH7 ····· .....
_..·········· .. ···· ...
WORKAREA
AUTHORIZED PERSONNEL ONLY.
....... WHEEL CHOCKS. . .....
BOTH REAR
WHEELS.
. ............ . . ..
'
WHEELCHci~
. .
- ·...... .-----· .· /
A
HAZARD, KEEP OUT,
. . AUGER DRIVE AREA.
SUPPORT DISCHARGE END.
SAFETY GUARD DESCRIPTION
PTO DRIVE GUARD
HOPPER FLIGHT GUARD
HOPPER DRIVE GUARD
SWING HEAD GUARD
TRANSPORT AND PLACEMENT
MOVING THE AUGER WITH THE
TOWING VEHICLE TO OR FROM THE
WORK AREA.
MOVING THE AUGER WITH THE
TOWING VEHICLE INTO OR OUT OF
ITS WORKING POSITION.
•
•
•
•
•
•
•
Always transport your auger in the full down
position. The Tube Assembly should be seated in
the A-Frame cradle.
Make sure that the hitch pin is securely attached
and an alternate safety chain is secured to the
auger and towing vehicle.
Ensure Lift Arm Safety Chain is attached to
Hopper.
Once the auger is hitched to the vehicle, ensure
that the jack is swung up into the transport
position.
Be alert of overhead obstructions and electrical
wires. Electrocution can occur without direct
contact. Failure to do so will result in severe
injury or death.
Never allow persons to stand underneath or ride
on the auger when it is being transported .
/). KEEPAWAY!
.aA OVERHEAD WIRES
II
•
•
•
•
•
Always move an auger with a vehicle, never
manually.
Lift slowly, no higher then the hitch bar. Be
sure grain is out of tube and auger is on a level
surface.
Do not place lumber under wheels for increased
height.
Before raising, check for power lines.
When auger is in place, anchor intake end and/or
discharge end and chock wheels.
When in transport or placement, PTO shaft
should be disconnected.
OVERHEAD WIRES
KEEP AWAY!
START UP AND BREAK IN
EMERGENCY SHUT DOWN
Sakundiak Equipment recommends that you do the following before augering grain with your new auger:
•
•
•
•
•
Run that grain auger at approximately l/2 the
normal operating speed (225 rpm with PTO)
without adding grain to the intake for approximately
5 minutes.
Bring auger up to full operation speed (450 rpm
with PTO) and slowly add grain to the hopper.
Continue to add grain slowly until approximately
1000 bushels (28 tonnes) has been loaded through
the grain auger. This will "shine up" the flighting and
the tube.
The operator should be aware of any unusual
vibrations or noises, determine source and shut
down. LOCK OUT POWER SOURCE BEFORE
SERVICING OR ADJUSTING.
OLD AUGER START UP AND BREAK IN
Sakundiak Equipment recommends that you do the
following before augering grain with your used auger:
•
•
•
•
Before positioning the auger, be sure all guards and
shields are in place, securely fastened and fully
operational.
Check oil level in gear boxes, fill if necessary and
lubricate all grease fittings.
Ensure PTO shaft is securely fastened.
Check the lift cable before each use and replace if
frayed or damaged .
CAUTION
•
•
•
•
•
Observe work area restrictions (see work area
diagram)
Keep all safety guards and shields in place.
Make certain everyone is clear before operating or
moving the machine.
Keep hands and feet away from all moving parts .
Lock out power source to adjust, service or clean .
•
•
Should the auger be immediately shut down under
load, lock out the power source and disconnect PTO
shaft. Empty grain from hopper and auger. Starting
the auger under load may result in damage to the
grain auger.
Before restarting, make certain everyone is clear of
the designated work area .
Start grain auger at a reduced speed .
NORMAL SHUT DOWN
•
•
Make sure that the hopper and auger are empty
before stopping the unit.
Lock out power source and remove PTO shaft.
CLEAN UP AND STORAGE
When the operation is completed , it is recommended
that you move the auger to the new work area or to a
storage area.
• Remove barriers, anchors and wheel chocks . Clean
entire work area.
• Remove PTO shaft and move auger slowly out of
work area.
• Lower auger to full down position immediately upon
clearance of any obstruction.
• The auger should be stored in the full down position.
• Do not attempt to pull grain auger out of snow
bank in winter. This will cause damage to the tube
assembly.
• Ensure that there is no snow build up on the auger
tube while in storage to prevent damage to the
auger.
• Store auger with the hopper in the tipped position.
• CAUTION! Maintain a minimum 4" lap on the
tumbler shields. Do not engage power take-off until
all personnel are clear of tractor, tumbler shaft and
auger. Ensure ends are fastened securely to the
auger and tractor.
• When installing PTO, ensure CV end goes to tractor.
AUGER LUBRICATION AND MAINTENANCE
DANGER!
Do not service or lubricate while the auger is running. LOCK OUT THE POWER SOURCE.
GEAR BOX
•
•
•
•
12 inch grain augers, fill with 1/2 quart (1/2 litre) of #90 gear oil.
Do not over fill gear box.
Change oil once a year.
Grease U-Joint once a day.
HEAD END
•
The bearings are pre-lubricated at the factory and have grease fittings for future lubrication.
HOPPER
•
•
•
•
All hopper bearings are pre-lubricated and do not require further lubrication.
Grease U-Joint and bushings once daily.
Grease hopper wheels once every season.
Drive chains should be oiled with #130 gear oil once every season.
HOPPER LIFT
•
Cable rollers should be oiled once a season.
BOOT DRIVE CHAIN
•
The drive chain should be oiled with #130 gear oil once every season.
PTO SHAFT
•
PTO shaft and attachment should be greased once a day with a good quality grease.
A CAUTION
A
WARNING
To Prevent Serious Injury or Death
1. Do not operate this auger before reading and
understanding the operators manual.
-Avoid unsafe operation or
maintenance.
2. Do not operate this auger unless all guards and
safety devices are securely in place.
-Do not operate or work on this
machine without reading and
understanding the operator's
manual.
3. Do not adjust, service, lubricate, clean, unclog or
move this unit until all power has been shut off.
-If manual is lost, contact your
nearest dealer for a new manual.
4. Make certain everyone is clear of the equipment
before moving or operating. Never allow children,
vis itors or untrained personnel in the area.
5. Keep hands, feet and clothing clear of all moving
parts while in operation.
6. Support discharge end or anchor intake end to
prevent upending.
7. Empty auger and lower to transport position before
moving to prevent upending.
8. Lower this unit to transport position when not in use.
9. When raising or lowering auger watch for overhead
powerlines and other obstructions.
10. Disengage belt tension release on motor base before
starting motor.
11. Disconnect power on electric motor driven units
before resetting motor overload, make certa in
electric motors are properly grounded.
12. Always make certain that trained personnel are in
attendance while unit is in operation
A DANGER
Y<11
Upending Hazard
The intake end of the auger must
always have downward weight.
Always test it before releasing it from
the vehicle or holddown.
Lift the intake slowly and keep it no
higher than the tractor tow bar when
attactching or releasing it.
Immediately lower the auger to
transport position before moving .
Failure to do so will cause upending,
which will result in serious injury or death.
A CAUTION
CLOSE VALVE IN THE LIFT
CYLINDER HYDRAULIC LINE
AFTER RAISING AUGER
INTO POSITION
A
DANGER
ELECTROCUTION HAZARD
~
To prevent serious injury or death from
electrocution:
.Stay away from overhead powerlines
when transporting or raising augers.
This machine is not grounded.
Electrocution can occur without direct contact
A CAUTION
A CAUTION
P.T.O. OPERATION
P.T.O. OPERATION
@k
- Conne~::t C.V. end of P.T.O. to tractor.
·Do not exceed 25 degrees In either direction.
-Disconnect P.T.O. If angle e:o:ceeds more than 25 degrees during
alight tum.
-When moving or positioning auger, always disconnect P.T.O.
from tra<:tor and place P.T.O. in holder.
-Failure to follow the above list will damage the C.V. joint.
• Main~in 36" · 38" dis~nce between tractor stub and auger stub
by repositioning the adjustable auger hitch.
.
Main~in
a minimum ""lap on tumbler shields.
A DANGER
~
ROTATING FLIGHTING
Keep away from intake end. Failure to do
so will result in serious Injury or death.
Do not use the auger without Intake guard
in place
A WARNING
~~
~@
40
~
MOVING PART HAZARD
moving parts :
-C lose and secure guards and shields
before starting.
-Keep hand, feet, hair, and clothing away
from moving parts.
-Disconnect and lockout P:OWer source
before adjusting or servicing.
-Do not stand or climb on machine when
operating.
A DANGER
.]""Q~~r;,
ROTATING DRIVELINE
CONTACT CAN CAUSE DEATH
KEEP HANDS, FEET HAIR AND CLOTHING
AWAY FROM MOVING PARTS
Do not operate without-AU driveline, tractor and equipment shields
in place.
-Drive lin es securely attached at both ends.
-Drive line shields that turn freely on driveline.
AWARNING
~ \~
HIGH PRESSURE FLUID HAZARD
To prevent serious injury or death
- Relieve pressure on system before
repairing or adjusting or disconnecting.
-Wear proper hand and eye protection
when searching for leaks. Use wood or
cardboard instead of hands.
-Keep all components in good repair.
A
WARNING
~~
~©
A
DANGER
40
~
~
MOVING PART HAZARD
TY~~
moving parts :
-Close and secure guards and shields
before starting .
from moving parts.
-Disconnect and lockout power source
operating.
ROTATING FLIGHTING
Keep away from intake end. Failure to do
so will result in serious injury or death .
Do not use the auger without intake guard
in pl ace .
A
WARNING
~~
~©
40
~
MOVING PART HAZARD
moving parts :
-Close and secure guards and shields
before starting.
from moving parts.
-Disconnect and lockout power source
operating .
SET UP PROCEDURE
Note: Reference to right and left hand used throughout this manual refers to the position standing at the intake enc
looking towards the head end.
1.
Follow and complete steps 1 thru 20 on page
14 using page 15 reference drawings and then
proceed to step 2 on this page.
2.
Follow and complete steps 1 thru 8 on page 16
and then proceed to step three on this page.
3.
and then proceed to step 4 on this page.
4.
5.
6.
Place assembled (FIG. 9) under assembled (FIG.
1). Connect the two assemblies with two 1"
dia. x 2-1/2" bolts and lock nuts. NOTE: Refer
to (FIG. 1) for top lift frame assembly mounting
location. Proceed to step 7 on this page.
7.
8.
Lift the now assembled (FIG. 1 & 9) together and
position it over the partially assembled (FIG. 10).
Line up bottom of top lift frame to the top of the
bottom lift frame. Install a pivot bushing to each
side. Fasten the assemblies together at each side
with 1" dia. x 8" bolt, two plated washers and a
lock nut. Proceed to step 8 on this page.
9.
Follow and complete steps 1 thru 6 on page 20,
10.
Hydraulic lines:
Short line connected to upper steel hydraulic line
and hydraulic cylinder.
Connect valve to the lower steel hydraulic line
and then attach long line to valve. Complete long
line assembly with pioneer tip.
Proceed to step 11 on this page.
11.
12.
13.
14.
Check that all bolts are tightened, pins are in
place, fittings are greased and that all safety
guards and shields are installed. Ensure proper
air pressure in all tires.
15.
Ensure Rod is tightened at the bottom hole
of Tension Bracket #1 on the side of hopper
transport location and at the top hole of Tension
Bracket #2 on the opposite side of the hopper
transport location. See Figure 14 on this page.
Raise the auger tube assembly and then
continue with steps 7 thru 17 on page 19 before
proceeding with step 9 on this page.
TENSION BRACKET #2
TENSION BRACKET #1
ROD
FIGURE 14
' OPERATORS MANUAL SLMD12 SERIES
TUBE ASSEMBLY AND TRUSS ASSEMBLY
1.
2.
3.
4.
5.
6.
Connect tube assembly A to tube assembly B as
shown in (FIGURE 01) , ensure proper alignment
of flight assemblies . Note: For the SLMD122400 and SLMD12-2600, there are three tube
assemblies to connect.
Lift BOOT END of TUBE ASSEMBLY min. 24"
high.
Position one SHORT CABLE and one LONG
CABLE straight and flat on floor and to the left
and right side of the tube assembly.
Install SHORT CABLE spanning from (FIGURE
03 to 05) . See (FIGURE 01). Fasten to (FIGURE
05) first using 5/8" dia. bolt, flat washer and
bushing. Tighten.
Fasten SHORT CABLE to bottom two holes in
(FIGURE 04) using 3/8" cable clamp and nuts.
Leave loose.
In (FIGURE 03) partially thread one of the two
nuts to eyebolt while attaching eyebolt to TUBE
SADDLE.
8.
Thread SHORT CABLE thru eyebolt and pull
tight. Attach two 5/16" cable clamps as shown
in (FIGURE 03).
9.
Tighten partially threaded nut on eyebolt until
adequate tension is achieved on SHORT CABLE.
10.
Thread second nut to eyebolt and lock.
11.
Repeat steps 5- 10 to install second SHORT
CABLE.
Install LONG CABLE spanning from (FIGURE 02
to 06). See (FIGURE 01). Fasten to (FIGURE
06) first using 5/8" dia . bolt, flat washer and
bushing. Tighten .
13.
14.
In (FIGURE 02) partially thread one of two
nuts to eyebolt while attaching eyebolt to TUBE
SADDLE .
15.
Thread LONG CABLE through eyebolt and pull
tight. Attach two 5/16" cable clamps as shown
in (FIGURE 02).
16 .
Tighten partially threaded nut on eyebolt until
adequate tension is achieved on LONG CABLE .
17.
Thread second nut to eyebolt and lock.
18.
Repeat steps 12- 17 to install second LONG
CABLE.
19.
Lower BOOT END to floor and tighten all truss
riser cable clamps .
20.
Refer to SET-UP PROCEDURES page 13 step 2
for the next set of instructions.
Assemble truss risers (FIGURES 03, 04 and 05)
in the order indicated in (FIGURE 01).
7.
12.
(FIGURE 03, 04 and 05) using 3/8" cable clamp
and nuts. Leave loose.
Fasten LONG CABLE to top two holes in
TUBE ASSEMBLY AND TRUSS ASSEMBLY
BOOT-END
MAIN FRAME ASSEMBLY BASE PLATE
TOP LIFT FRAME ASSEMBLY BASE PLATE
FIGURE 01
LONG CABLE
FIGURE 02
FIGURE 03
LONG CABLE
""''"~
SHORT CABLE
FIGURE 04
FIGURE 05
FIGURE 06
WINCH ASSEMBLY
1.
Attach item 1 to item 2 with three 3/8" dia.
carriage bolts and nuts. Leave loose. See
(FIGURE 07).
5.
Mount items 1 and 2 to item 3 using 1/2" dia. x
8" bolt and lock nut at boot end and 1/2" dia . x
9" bolt and lock nut at head end.
2.
Install item 4 to item 1.
6.
3.
Position item 5 on item 6 and 4.
7.
Insert item 8 thru items 7 and 6.
4.
Tighten chain by pulling winch assembly towards
the head-end and tighten the three carriage bolts
from step 1.
8.
FEED TUBE ASSEMBLY HEAD END
(FIGURE 12 &13}
HITCH ASSEMBLY
1.
2.
Install item 1 onto item 2 using 5/8" dia U-bolt,
washers and lock nuts and three 1/2" dia. bolts
and lock nuts at the underside of the tube flange
and four 1/2" dia. bolts and nuts at tube base
mount.
Insert item 6 into item 2 and lock in place using
item 3.
3.
Insert item 4 through item 3.
4.
Refer to SET-UP PROCEDURE page 13 step 4
5.
After completion of SET-UP PROCEDURE steps
1 through 10, continue with HITCH ASSEMBLY
steps 6 through 9.
6.
Insert item 2 into item 6.
7.
Insert item 7 through items 6 and 2.
8.
Insert item 8 through item 7.
9.
FEED TUBE ASSEMBLY HEAD END
(FIGURE 12 & 13)
e
,yy~
TUBE
FLANGE
/
5/8" DIA.
U-BOLT
FIGURE 08
'
HITCHEND \
\ @)
~
TOP LIFT FRAME ASSEMBLY
1.
Lay frame out as shown in (FIGURE 09).
5.
Connect item 6 to item 3 using 5/8" dia. bolts,
washers and nuts.
2.
Fasten item 4 to item 5 using 1-1/8" dia. bolt
and lock nut.
6.
washers and nuts.
washers and nuts.
7.
washers and nuts.
Connect item 1 to item 3 using 5/8" dia . bolts,
washers and nuts.
8.
3.
4.
'0.
3
1~
BOTTOM LIFT FRAME
ASSEMBLY END
(FIGURE 01)
FIGURE 09
TUBE ASSEMBLY END
(FIGURE 01)
FRAME ASSEMBLY
1.
Lay frame out as shown in (FIGURE 10). Ensure
item 4 (axle) is on jack stands prior to beginning
assembly.
10.
Fasten item 11 to item 1 using 5/8" dia. x 1-1/2"
bolts, lock washer and nut.
11.
Fasten item 14 to item 3 using 5/8" dia. x 1-1/2"
bolts, lock washer and nut.
2.
Fasten items 6 and 7 to item 4 using 1" dia.
bolts and lock nuts.
12.
3.
Install items 8 and 9 to item 6 and 7 using 5/8"
dia. bolts and nuts.
Install item 12 in top holes of items 11 and 14
using 5/8" dia. x 4" bolt, lock washer and nut.
13.
4.
Mount tires on rims and mount rims on axle
spindles.
Install item 13 in bottom holes of items 11 and
14 using 5/8" dia. x 4" bolt, lock washer and
nut.
5.
Insert items 10 inside of item 4 using items 5
and hairpin.
14.
Place item 15 on top moon shape cut out of item
11.
6.
for next set of instructions .
15.
Place item 16 on bottom moon shape cut out of
item 14.
7.
After completion of SET-UP PROCEDURE steps
1 through 8. Continue with FRAME ASSEMBLY
steps 8 through 17 .
16.
Slide item 17 through items 16 and 15 and
fasten with 1" nut.
17.
8.
Install item 2 to items 1 and 3 using 5/8" bolts.
for next set of instructions.
9.
Fasten item 8 to items 6 and 7 using 5/ 8" dia .
U-bolts.
TOP LIFT FRAME
ASSEMBLY END
(FIGURE 09)
TUBE ASSEMBLY END
(FIGURE 01)
FIGURE 10
LIFT ARM ASSEMBLY
1.
Slide LIFT ARM ASSEMBLY into SADDLE
ASSEMBLY and fasten in place using items 3
and 5 .
2.
Install CABLE ROLLER ASSEMBLY #1 and item
7 on to pin .
3.
Thread cable end from winch around CABLE
ROLLER ASSEMBLY #1 and #2 through PIPE
and around CABLE ROLLER ASSEMBLY #3 .
/
4.
Slide cable through item 2. Locate item 2 7"
from cable end . Bend the last 7" of cable back
onto itself and fasten using item 1. Locate item 1
4" above item 2.
5.
Slide item 6 over PIN on SADDLE ASSEMBLY
and lock in place with item 4.
6.
CABLE ROLLER
ASSEMBLY #3
PIPE
LIFT ARM
ASSEMBLY
2
CABLE ROLLER
ASSEMBLY #2
SAFETY
HOOK
FIGURE 11
FEED TUBE ASSEMBLY
1.
Assemble item 1 to item 2 with two 5/8" dia. x
1-1/2" UNC bolt c/w lock nut.
2.
Install UNIVERSAL JOINT to top end of GEAR
BOX SHAFT.
3.
Push item 3 between items 1 and 2.
4.
Fasten item 3 to item 1 and 2 using two items 4.
5.
6.
Attach item 7 to item 2 with three 1/4" dia. x
3/4" whiz bolts c/w whiz nuts.
7.
UNIVERSAL JOINT
GEAR BOX SHAFT
HOPPER ASSEMBLY END -----"
(FIGURE 13)
/"--,
/
/
2
FIGURE 12
HOPPER ASSEMBLY
1.
Fasten item 3 to item 2 with two 1/2" dia. x
1-1/4" bolts and whiz nuts.
5.
Bolt the four items 1 to item 2 using 3/4" dia . x
8-1/2" bolt, plate washer and lock nut.
2.
Assemble item 4 to item 5 with three 1/4" dia. x
3/4" whiz bolts and whi z nuts.
6.
Place 3/8" dia . x 1-1/2" bolt through item 3 and
set items 7 and 8 over bolt. Fasten assembly
with lock nut.
3.
Attach item 6 to item 5 using two 1/4" dia. x
3/4" whiz bolts and whiz nuts .
7.
Assemble FEED TUBE ASSEMBLY and HOPPER
ASSEMBLY (FIGURES 12 and 13) with eight
3/8" x 1" carriage bolts and whiz nuts.
8.
4.
Install item 4, 5 and 6 assembly to item 2 with
three 1/4" dia. x 3/4" whiz bolts and whiz nuts.
Ensure assembly is pulled towards FEED TUBE
ASSEMBLY END before tightening bolts.
FEED TUBE ASSEMBLY END
(FIGURE 12)
FIGURE 13
MAIN FRAME
6 ~ -~9
REF NO.
PART#
DESCRIPTION
NO. USED
2
3007
2
BOLT- 1/2" x 1-1/4" c/w LOCK WASHER
PLATED WASHER- 1/2" ID x 2-l/4" OD
3
3352
3
3353
1
1
MAIN FRAME ASSEMBLY (LEFT HAND)- SLMD12-2200
3
3354
1
4
5
3159
1
2
1
6
7
8
9
9
9
10
11
12
13
14
24
LOWER SUPPORT ASSEMBLY
UNC BOLT- 5/8" x 1-l/2" c/w LOCK WASHER AND NUT
-
2
HAIR PIN- 1/8" x 2-3/ 8"
3384
-
2
2
UNC BOLT- 1" x 5" c/w LOCK NUT
3160
1
AXLE ASSEMBLY- SLMD12-2200
3161
1
3162
1
DRAW PIN - 3/4" x 6"
1
NUT- 1"
3378
3379
1
1
THREADED ROD SWIVEL ASSEMBLY
TIE ROD BRACKET ASSEMBLY (LEFT HAND)
2
3377
1
TIE ROD ASSEMBLY
TIE ROD BRACKET ASSEMBLY (RIGHT HAND)
3381
15
16
3382
1
THREADED ROD LOCK SWIVEL ASSEMBLY
17
3380
4
1
THREADED ROD ASSEMBLY
18
18
3355
3356
1
1
18
3357
1
19
20
3156
12
3138
2
21
22
3132
3134
2
23
24
UNC BOLT- 5/ 8" x 4" c/w LOCK WASHER AND NUT
MAIN FRAME ASSEMBLY (RIGHT HAND)- SLMD12-2200
WHEEL BOLT- 1/ 2" x 1-1/4" UNF
RIM- 16"
2
DUST CAP
CASTLE NUT
3135
2
TAPERED ROLLER BEARING CONE (OUTER)
3131
2
HUB
25
1005
2
TAPERED ROLLER BEARING CONE (INNER)
26
27
3176
2
AXLE EXTENSION ASSEMBLY
3136
2
28
29
3137
2
SPINDLE WASHER
TAPERED ROLLER BEARING CUP (OUTER)
1006
2
TAPERED ROLLER BEARING CUP (INNER)
30
31
3133
2
GREASE SEAL
3358
-
HUB & SPINDLE- COMPLETE
A-FRAME
DESCRIPTION
REF NO.
PART#
NO. USED
1
1
1
3251
3299
1
BOTTOM LIFT FRAME ASSEMBLY (LEFT HAND)- SLMD12-2400
1
3252
1
BOTTOM LIFT FRAME ASSEMBLY (LEFT HAND)- SLMD12-2600
BOTIOM LIFT FRAME ASSEMBLY (LEFT HAND)- SLMD12-2200
2
-
44
3
4
3169
1
BOTTOM LIFT FRAME CROSSBRACE ASSEMBLY
3365
1
BOTTOM LIFT FRAME CYLINDER MOUNT ASSEMBLY- SLMD12-2200
4
4
3366
1
3367
1
BOTIOM LIFT FRAME CYLINDER MOUNT ASSEMBLY- SLMD12-2400
BOTIOM LIFT FRAME CY LINDER MOUNT ASSEMBLY- SLMD1 2-2600
5
2995
6
7
-
6
2
PLATED WASHER- 1-1/16" ID x 2-1/4" OD
UNC BOLT- 1" x 8" c(w LOCK NUT
PIVOT BUSHING
TOP LIFT FRAME ASSEMBLY (LEFT HAND)- SLMD12-2200
UNC BOLT- 5/8" x 1-1/2" c/w LOCK WASHER AND NUT
3362
3177
2
8
8
3255
8
9
3256
1
1
3259
1
BOTIOM CYLINDER MOUNT PIN
10
3257
2996
1
HYDRAULIC CYLINDER
1
NPT VENT
1
TOP CYLINDER MOUNT PIN
13
3260
2997
1
REDUCED ORIFICE FITIING
14
-
2
BOLT- 1" x 2-1/2" c/w LOCK NUT
15
2994
2
16
3383
3244
1
17
1
BUSHING
TOP LIFT FRAME CROSSBRACE ASSEMBLY
BOTIOM LIFT FRAME ASSEMBLY (RIGHT HAND)- SLMD12-2200
17
3303
1
BOTTOM LIFT FRAME ASSEMBLY (RIGHT HAND) - SLM D12-2400
17
3363
3245
1
BOTIOM LIFT FRAME ASSEMBLY (RIGHT HAND) - SLMD12-2600
1
TOP LIFT FRAME ASSEMB LY (RIGHT HAND) - SLMD12-2200
3253
3254
1
1
TOP LIFT FRAME ASSEMBLY (RIGHT HAND)- SLMD12-2400
18
19
3167
TOP LIFT FRAME CRADLE ASSEMBLY- SLMD12-2200
19
3375
1
1
19
3376
1
20
20
3168
1
TOP LIFT FRAME CYLINDER MOUNT ASSEMBLY- SLMD12-2200
3368
1
1
21
3369
3385
22
3153
4
11
12
18
18
20
1
TOP LIFT FRAME ASSEMBLY (RIGHT HAND)- SLMD12-2600
SEAL KIT FOR HYDRAULIC CYLINDER
LYNCH PIN
PTO SHAFT ASSEMBLY
REF NO.
PART#
NO. USED
1
3411
2
3414
2
1
GUARD REPAIR KIT
YOKE, TUBE AND SLIP SLEEVE
DESCRIPTION
INNER GUARD
35R CROSS AND BEARING KIT
3
3413
1
4
3408
3415
3
1
BALL SHEAR ASSEMBLY
6
7
3406
2
SSUAUTO- LOK REPAIR KIT
3410
1
YOK E AND SHAFT
8
3409
1
CENTER HOUSING
SAFETY SLIDE LOCK YOKE ASSEMBLY
5
9
3407
1
10
3416
2
LOCK NUT
11
2
3/8" X 1" GRADE 5 BOLT
12
3417
3412
1
OUTER GUARD
13
14
3405
3404
-
JOINT AND TUBE HALF ASSEMBLY- INCLUDES REF #'S- 2,4,5
15
16
3401
3403
-
GUARD SET- INCLUDES REF #'S- 3,12
JOINT AND SHAFT HALF ASSEMB LY- INCLUDES REF #'S- 4, 7, 8, 9
17
3402
3330
-
JOINT AND SHAFT HALF ASSEMBLY
c/w NUT
JOINT AND TU BE HALF ASSEMBLY
PTO SHAFT ASSEMBLY COMP LETE
c/w INNER GUARD- IN CLUDES REF #'S- 2,3,4,5
c/w OUTER GUARD- INCLUDES REF #'S- 4, 7, 8, 9, 12
HOPPER
HOPPER
REF NO.
PART#
NO. USED
1
2
-
3029
8
1
WHIZ BOLT- 1/4" x 3/4" c/w WHIZ NUT
INSPECTION DOOR HANDLE
3
4
3227
3228
1
1
INSPECTION DOOR
INSPECTION DOOR HINGE
4
DESCRIPTION
6
3059
4
BOLT- 1/2" x 1-1/4"
PIVOT STOP
5
c/w WHIZ NUT
7
3225
1
HOPPER ASSEMBLY
8
3230
1
DRIVE SAHFT BUSHING HOLDER ASSEMBLY
9
1751
10
3048
2
11
3229
1
12
3042
13
LONG RUBBER BRACKET
DR IVE SHAFT ASSEMBLY
FLIGHT SHAFT BUSHING (FOR USE WITH PART# 3233)
x 1 c/w WHIZ NUT
c/w BUSHING
6
WHIZ BOLT- 3/8"
2
1
FLIGHT SHAFT BUSHING HOLDER
FLIGHT GUARD ASSEMBLY
16
3
CARRIAGE BOLT- 3/8"
17
4
CARR IAGE BOLT- 3/8"
14
3233
15
3236
18
3237
19
c/w BUSHING
DRIVE SHAFT BUSHING (FOR USE WITH PART# 3230)
1
20
x 3/4" c/w WHIZ NUT
x 1" c/w WING NUT
FLIGHT GUARD MOUNTING BRACKET
CARRIAGE BOLT- 5/16"
x 3/4" c/w WHIZ NUT
20
3049
2
21
3234
1
RIGHT HAND FLIGHT ASSEMBLY (LEFT HAND FLIGHT)
22
3058
1
INSPECTION DOOR CLOSURE WASHER
23
3057
1
IN SPECTION DOOR CLOSURE SPRING
24
3056
3226
1
INSPECTION DOOR CLOSURE
1
1
PIVOT ASSEMBLY
BOLT- 3/8" x 1-1/2"
2
8
UNC BOLT- 5/8" x 1-3/4" c/w PLATE WASHER AND LOCK NUT
CARR IAGE BOLT- 3/8" x 1" c/w WHIZ NUT
25
26
27
28
SHORT RUBBER BRACKET
c/w LOCK NUT
29
30
3261
2
2
PIVOT SPACER
BOLT- 5/16" x 3/4"
31
3232
32
3235
1
1
RUBBER
LEFT HAND FLIGHT ASSEMBLY (RIGHT HAND FLIGHT)
33
34
6
CARRIAGE BOLT- 3/8"
1239
35
2316
6
2
FLAGETIE
FLIGHT BEARING
SEALING PLATE
36
2777
37
3425
1
2
38
39
3061
3239
4
4
WHEEL SPACER
4
BOLT- 3/4"
40
c/w WHIZ NUT
x 1 c/w WHIZ NUT
DRIVE BEARING
WHEEL
c/w TIRE
x 9" c/w PLATE WASHER AND LOCK NUT
41
3240
1
CHAIN
42
3241
1
CHAIN
43
3238
1
DRIVE GUARD
44
3053
1
BEARING- 1-1/4"
45
46
3397
2
DRIVE SPROCKET
3398
1
REVERSE SPROCKET
47
3396
1
DOUBLE DRIVE SPROCKET
2
CHAIN TENSION HOLDER PLATE
48
49
3392
2
50
3391
2
2
CHAIN TENSION PLATE
51
52
2
DRAIN PLUG -CARRIAGE BOLT- 3/8"
2
x 1-1/2" c/w LOCK NUT
x 3/4" c/w WHIZ NUT
BOLT- 3/8" x 2-112" c/w LOCK NUT
CARRIAGE BOLT- 3/8"
53
54
3399
1
LEFT HAND FLIGHT EXTENSION ASSEMBLY (RIGHT HAND FLIGHT)
55
3400
1
RIGHT HAND FLIGHT EXTENSION ASSEMBLY (LEFT HAND FLIGHT)
FEED AUGER HEAD AND TUBE
REF NO.
PART#
NO. USED
DESCRIPTION
1
-
16
2
3220
1
RAIN GUARD (LEFT HAND)
3
3219
1
HEAD COVER ASSEMBLY
4
3221
5
1
RAIN GUARD (RIGHT HAND)
8
UNC BOLT- 3/8" x 1" c/w WHIZ NUT
GEAR BOX ASSEMBLY COMPLETE
6
3215
1
7
-
1
BOLT- 7/16" x 3" c/w LOCK NUT
8
3223
1
U-JOINT (FLIGHT TO GEAR BOX)
9
-
1
WOODRUFF KEY
10
3224
1
U-JOINT (GEAR BOX TO GEAR BOX)
11
3424
-
U-JOINT CROSS KIT
12
-
8
CARRIAGE BOLT- 7116" x 1-1/4" c/w WHIZ NUT
13
3214
1
HEAD ASSEMBLY
14
3216
4
PIVOT SPACER PLATE
15
3217
4
PIVOT TOP PLATE
16
3212
1
FEED AUGER TUBE ASSEMBLY
17
3128
1
U-JOINT- 1-1/4" TO 1" SQUARE
18
3035
1
SQUARE STUB
19
3213
1
FEED AUGER FLIGHT ASSEMBLY
20
3029
2
HANDLE
21
3222
1
HEAD COVER HINGE
22
-
2
UNC BOLT- 5/8" x 1-1/2" c/w FLAT WASHER AND LOCK NUT
23
3034
2
BUSHING- 1" OD x .188" WALL DOM x 1/2" LONG x 5/8" ID
24
3218
1
RUBBER TUBING
25
3329
2
RUBBER TUBING CLAMP
LIFT ARM
REF NO.
PART#
NO. USED
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
-
2
1
2
2
1
1
2
3
4
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3148
3147
3181
3151
3149
1782
-
3178
3189
3145
2700
3182
3154
3155
1387
2699
3153
DESCRIPTION
UNC BOLT- 5/8" x 2-1/2" c/w NUT AND LOCK WASHER
LIFT ARM PIVOT ASSEMBLY
LIFT ARM PIVOT ROLLER BEARING
BOLT - 1/2" x 3-1/2" c/w LOCKNUT
LIFT ARM PIVOT BASE ASSEMBLY
LIFT ARM PIVOT CO LLAR
BUSHING
CAB LE ROLLER ASSEMBLY
HEAVY 1-1/8" x 18 GAUGE MACHINERY BUSHING
CODER PIN- 1/8" x 3/4"
LIFT ARM TUBE ASSEMBLY
HAIR PIN
LIFT ARM SADD LE ROLLER COVER
LIGHT - 1-1/8" x 18 GAUGE MACHINERY BUSHING
LIFT ARM SAFETY CHAIN LUG
CAB LE CLAMP- l/4"
CARRIAGE BOLT- 3/8" x 1" c/w WHIZ NUT
LIFT HOOK
HOPPER LIFT CABLE
SAFETY HOOK c/w PIN AND CODER PIN
SAFETY CHAIN
LIFT ARM CABLE PIN
DRAW PIN
LYNCH PIN
TOP GEAR BOX
REF NO.
PART#
NO. USED
DESCRIPTION
1
3282
1
QUILL SEAL
2
3265
1
QUILL
3
3287
3
0-RING
4
3274
AS REQ'D
GASKET
5
3269
4
SNAP RING
6
3268
3
SPACER
BEARING CONE
7
3267
4
8
3258
4
BEARING CUP
9
3278
1
QUILL SHAFT
10
3284
2
SQUARE KEY
11
3272
2
GEAR
12
3283
1
CROSS SEAL
13
3266
1
CROSS END CAP
14
3280
1
CROSS SHAFT
15
3264
1
HOUSING
16
3277
2
PIPE PLUG
17
3270
1
18
3249
12
-
3215
-
END CAP
CAPSCREW
GEAR BOX ASSEMBLY COMPLETE (FEED AUGER HEAD END ASSEMBLY GEAR BOX)
REF NO.
PART#
NO. USED
I
3286
I
SHIELD
DESCRIPTION
2
3282
I
QUILL SEAL
3
3271
I
QUILL
4
3273
I
GREASE ZERK
5
3287
3
0-RING
6
3274
AS REQ'D
GASKET
7
3269
4
SNAP RING
8
3268
3
SPACER
9
3267
4
BEARING CONE
10
3258
4
BEARING CUP
11
3285
1
GREASE WASHER
12
3279
I
QU ILL SHAFT
13
3284
2
SQUARE KEY
14
3272
2
GEAR
15
3283
I
CROSS SEAL
16
3266
I
CROSS END CAP
17
3281
I
CROSS SHAFT
18
3264
I
HOUSING
19
3277
2
PIPE PLUG
20
3270
1
END CAP
21
3249
12
3262
CAPSCREW
GEAR BOX ASSEMBLY COMPLETE (BOOT ASSEMBLY GEAR BOX)
OPERATORS MANUAL SLMD
BOOT
~
'2V
36
BOOT
REF NO.
PART#
NO. USED
I
2711
I
REVERSE SHAFT
DESCRIPTION
2
3262
I
GEAR BOX ASSEMBLY (COMPLETE)
3
-
4
UNC BOLT- 1/2"
4
3116
x 1-3/4" C/w LOCK WASHER AND NUT
BRONZE BUSHING (FOR USE WITH PART# 3202)
5
3202
1
GEAR BOX BUSHING HOUSING ASSEMBLY
6
-
8
CARRIAGE BOLT- 7/16"
C/w BUSHING
x 1-1/4" C/w WHIZ NUT
7
3246
4
PIVOT TOP PLATE
8
3247
4
PIVOT SPACER PLATE
9
3243
1
PIVOT RING ASSEMBLY
10
3200
I
BOOT ASSEMBLY
II
6
UNC BOLT- GRADE 2 - 3/8"
12
6
CARR IAGE BOLT- 3/8"
FELT WASHER
x I" C/w LOCK NUT
x 3/4" c/w WHIZ NUT
13
2877
2
14
2827
3
BEARING INSERT
15
2715
3
SPROCKET (GEAR BOX CROSS SHAFT, REVERSE SHAFT & FLIGHT SHAFT)
C/w HOUSING (GEAR BOX CROSS SHAFT, REVERSE SHAFT INSIDE & OUTSIDE BOOT)
x 1-1/4"
I
SQUARE KEY- 5/16"
17
3211
I
DRIVE CHAIN
18
3206
1
DRIVE GUARD ASSEMBLY
19
3263
1
DRIVE GUARD HINGE
20
8
CARRIAGE BOLT- 1/4"
21
4
UNC BOLT- l/2"
1
REVERSE BEARING SH IELD
16
22
2714
23
24
3203
25
x 2" C/w LOCK WASHER AND NUT
4
BOLT - 5/8"
I
FLIGHT BUSHING HOUSING ASSEMBLY
I
CARRIAGE BOLT- 1/4"
I
INSPECTION DOOR
27
1
CARRIAGE BOLT- 1/4"
28
1
UNC BOLT- 3/8"
26
30 14
x 3/4" C/w WHIZ NUT
x 2-l/4" C/w LOCK NUT AND WASHER
x 3/4" C/w LOCK NUT
x 3/4" C/w WHIZ NUT
x 3/4" C/w WHIZ NUT
4
CARRIAGE BOLT- 3/8"
2708
2
CLEAN OUT DOOR LATCHES
31
3205
1
MAIN HITCH ASSEMBLY
32
3164
I
MAIN HITCH CONNECTOR PLATE
33
-
2
WOODRUFF KEY l/4"
34
3209
I
BEARING INSERT
35
2
CARRIAGE BOLT- 3/8"
36
2
SPRING PIN
29
30
x I"
c/w HOUSING (FLIGHT SHAFT)
x 3/4" c/w WING NUT
37
2699
I
DRAW PIN
38
3201
I
CLEAN OUT DOOR ASSEMBLY
39
2725
I
JACK
40
3020
I
U-BOLT
2
BOLT- l/2"
41
C/w DRAW PIN & SPRING PIN
c/w LOCK WASHERS AND NUTS
x 1-l/2" C/w LOCK WASHER AND NUT
42
2723
I
HITCH INSERT ASSEMBLY
43
-
4
WHIZ BOLT- 1/4"
4
UNC BOLT- 3/8"
PTO GUARD
44
45
3370
1
46
2620
I
PIN - 3/8"
I
UNC BOLT- 3/8"
47
c/w BUSHING
x 3/4" c/w WING NUT
x 5/8" c/w WHIZ NUT
x I " C/w WHIZ NUT
x 4"
x 4-1/2" C/w LOCK NUT
48
2883
I
PTO BRACKET - LEFT
49
2882
1
PTO HOLDER ASSEMBLY
50
2884
1
PTO BRACKET- RIGHT
51
3042
BRONZE BUSHING (FOR USE WITH PART# 3203)
52
1578
53
3207
-
BEARING INSERT
C/w COLLAR (FOR USE WITH PART# 2827)
BEARING INSERT C/w COLLAR (FOR USE WITH PART# 3209)
TUBE ASSEMBLY - 2200
1~
~ .
.....:
.,.
..
TUBE ASSEMBLY - 2200
REF NO.
PART#
NO. USED
1
-
4
2
3199
1
HEAD END PLATE
3
3209
1
BALL BEARING INSERT
1
BOLT- 1!2"
4
DESCRIPTION
BOLT- 5/8"
x 1-3/4" c/w LOCK WASHER AND NUT
c/w HOUSING
x 1-1/4" c/w LOCK WASHER
5
3196
1
TOP FLIGHT ASSEMBLY- SLMD12-2200
6
3193
1
TOP TUBE ASSEMBLY- SLMD12-2200
12
7
x 1" c/w WH IZ NUT
WHIZ BOLT- 1/2"
HYDRAULIC HOSE AT FLANGE
8
3371
1
9
3300
1
PLATED HYDRAULIC LINE- SLMD12-2400
2
UNC BOLT- 5/8"
CABLE BUSHING
10
x 2" c/w 5/8" WASHER, LOCK WASHER AND NUT
11
3070
2
12
3372
1
HYDRAULIC HOSE AT CYLINDER- SLMD12-2200
13
-
8
WHIZ BOLT- 5/16"
x 1" c/w WHIZ NUT
14
3248
1
ANGLE SPOUT ASSEMBLY
15
3175
1
BOTIOM FLIGHT ASSEMBLY
16
3172
1
BOTIOM TUBE ASSEMBLY- SLMD12-2400
17
-
33
WHIZ BOLT- 1/2"
x 1-1/4" c/w WH IZ NUT
18
3
WHIZ BOLT- 1!2"
x 1-3/4" c/w WH IZ NUT (3 BOTIOM BOLTS AT BOOT FLANGE ONLY)
19
3095
13
HYDRAU LI C LI NE CLIP- SLMD12-2200
13
SELF THREADING SCREW- 1/4"- SLMD12-2200
20
21
3096
1
HYDRAU LI C LINE SPLICE CONNECTOR
22
3188
1
PLATED HYDRAULIC LINE- LONG
23
1725
1
NEEDLE VALVE
24
3093
2
HYDRAULIC HOSE CONNECTOR
25
3187
1
PLATED HYDRAU LI C LINE- SHORT
26
3113
1
MA LE PIONEER TIP
27
3088
1
HYDRAULIC HOSE
28
3207
BEARING INSERT
c/w ENDS
c/w COLLAR (FOR USE W ITH PART# 3209)
TUBE ASSEMBLY- 2400 & 2600
2
TUBE ASSEMBLY - 2400 & 2600
REF NO.
PART#
NO. USED
1
3197
1
1
3198
1
2
3194
1
2
3195
1
3
DESCRIPTI ON
12
WHIZ BOLT- 1/2"
x 1" c/w WHIZ NUT
4
3199
1
HEAD END PLATE
5
3209
1
BALL BEARING INSERT
6
-
1
BOLT- 1/2"
7
3170
1
MIDDLE FLIGHT ASSEMBLY
8
3248
1
ANGLE SPOUT ASSEMBLY
9
-
8
WHIZ BOLT- 5/16"
10
3297
1
MIDDLE TUBE ASSEMBLY- SLMD12-2400
10
3298
1
MIDDLE TUBE ASSEMBLY- SLMD12-2600
11
4
BOLT- 5/8"
12
-
49
13
3371
1
HYDRAULIC HOSE AT FLANGE
14
3301
1
14
3302
15
c/w HOUSING
x 1-1/4" c/w LOCK WASHER
x 1" c/w WHIZ NUT
x 1-3/4" c/w LOCK WASHER AND NUT
x 1-1/4" c/w WHIZ NUT
WHIZ BOLT- 1/2"
1
2
UNC BOLT- 5/8"
x 2" c/w 5/8" WASHER, LOCK WASHER AND NUT
16
3()7'(;-
2
CABLE BUSHING
17
3373
1
17
3374
1
18
3175
1
BOTIOM FLIGHT ASSEMBLY
19
3173
1
19
3174
20
1
3
WHIZ BOLT- 1/2"
13
HYDRAULIC LINE CLIP- SLMD12-2400
x 1-3/4" c/w WHIZ NUT (3 BOTIOM BOLTS AT BOOT FLANGE ONLY)
21
3095
21
3095
14
HYDRAULIC LINE CUP- SLMD12-2600
22
-
13
22
-
14
23
3096
1
24
3188
1
PLATED HYDRAULIC LINE- LONG
25
1725
1
NEEDLE VALVE
26
3093
2
HYDRAULIC HOSE CONNECTOR
27
3187
1
PLATED HYDRAULIC LINE- SHORT
28
3113
1
MALE PIONEER TIP
29
3088
1
HYDRAULIC HOSE
30
3207
-
BEARING INSERT
HYDRAULIC LINE SPLICE CONNECTOR
c/w ENDS
c/w COLLAR (FOR USE WITH PART# 3209)
TRUSS ASSEMBLY
BOOT-END
MAIN FRAME ASSEMBLY MOUNTING PLATE
A-FRAME ASSEMBLY MOUNTING PLATE
SLMD12 TRUSS ASSEMBLIES KEY PLAN
FIGURE Kl
FIGURE K2
FIGURE K4
FIGURE K3
~
FIGURE KS
TRUSS ASSEMBLY
REF NO.
PART#
NO. USED
DESCRIPTION
c/w
1
3087
4
EYE BOLT
2
3313
1
LONG TRUSS CABLE- SLMD12-2200
TWO NUTS
2
3185
1
2
3186
1
3
8
CABLE CLAMP - 5/ 16"
4
20
UNC BOLT- 7/16"
x 1-1/4" c/w WHIZ NUT
5
3180
2
6
3068
4
SMALL TRUSS BRACE
SMALL TRUSS RISER
7
-
8
CABLE CLAMP- 3/8"
8
3314
1
SHORT TRUSS CABLE- SLMD12-2200
8
3183
1
8
3184
1
LARGE TRUSS RISER
9
3079
2
10
3078
2
LARGE TRUSS BRACE
11
-
1
BOLT- 7/16"
12
3179
1
LARGE TRUSS SPACER
13
3070
4
CABLE BRACKET BUSHING
4
UNC BOLT- 5/8"
14
x 3" c/w WHIZ NUT
x c/w WAS HER, LOCK WASHER AND NUT
FULTON K1550 BRAKE WINCH
REF NO.
PART#
1
-
2
NO. USED
DESCRIPTION
1
FRAME SPACER
1
LOCK NUT- 3/8 "
1
INPUT SHAFT
1
FRAME
-
3
LOCK NUT- l/2"
6
1672
1
CABLE CLAMP
7
1673
1
DRUM ASSEMBLY
1
KEEPER
9
-
1
UNC BOLT- 1/2"
10
1937
2
BUSHING
11
1947
1
PINION AND DISK
12
1677
2
BRAKE PAD
13
1932
1
RATCHET GEAR
14
1933
1
SHAFT BRAKE DISK
15
1712
1
PAWL AND SPRING KIT
1
UNC BOLT- 3/8'
1
SPACER
HANDLE
3
1936
4
5
8
16
17
1934
18
1711
1
19
-
1
-
1671
x 5-3/4 "
x 5-3/4 "
NYLON LOCK NUT- 1/2"
FULTON K1550 BRAKE WINCH ASSEMBLY- COMPLETE
BOLT ON WINCH PLATE
REF NO.
PART#
NO. USED
1
2717
1
1
WINCH HANDLE ASSEMBLY
HAIR PIN
WINCH CHAIN
DESCRIPTION
2
-
3
4
1175
1
-
1
BOLT- 1/2"
5
3126
1
6
2713
2
WINCH DRIVE SHAFT ASSEMBLY
WINCH DRIVE SHAFT BEARING (COMP LETE)
x 8" C/w
LOCK NUT
7
CARR IAGE BOLT- 3/8" x 3/4" C/w WHIZ NUT
WINCH DRIVE SHAFT BEARING (INSERT ONLY)
1
1
SPROCKET
1671
11
3125
1
BOLT ON WINCH PLATE
12
-
1
BOLT- 1/2"
7
2718
8
9
3103
10
WINCH ASSEMBLY
x 9" C/w
LOCK NUT
REF.
PART#
PAGE
REF.
PART#
PAGE
REF.
PART#
PAGE
REF.
PART#
PAGE
25
29
3
34
22
52
1005
1006
1175
1239
1387
1578
1671
1671
1672
1673
1677
1711
1712
1725
1725
1751
1782
1932
1933
1934
1936
1937
1947
2316
2620
2699
2699
2700
2708
2711
2713
2714
2715
2717
2718
2723
2725
2777
2827
2877
2882
2883
2884
2994
2995
2996
2997
3007
3014
3020
3029
3029
3034
3035
3042
3042
3048
3049
3053
3056
3057
3058
3059
3061
3068
3070
3070
3070
3078
3079
3087
3088
3088
3093
3093
3095
3095
3095
23
23
41
27
29
33
40
41
40
40
40
40
40
35
37
27
29
40
40
40
40
40
40
27
33
29
33
29
33
33
41
33
33
41
41
33
33
27
33
33
33
33
33
24
24
24
24
23
33
33
27
28
28
28
27
33
27
27
27
27
27
27
27
27
39
35
37
39
39
39
39
35
37
35
37
35
37
37
21
23
9
26
28
4
3096
3096
3103
3113
3113
3116
3125
3126
3128
3131
3132
3133
3134
3135
3136
3137
3138
3145
3147
3148
3149
3151
3153
3153
3154
3155
3156
3159
3160
3161
3162
3164
3167
3168
3169
3170
3172
3173
3174
3175
3175
3176
3177
3178
3179
3180
3181
3182
3183
3184
3185
3186
3 187
3187
3 188
3188
3189
3193
3194
3195
3196
3197
3198
3199
3199
3200
3201
3202
3203
3205
3206
3207
3207
3207
3209
3209
3209
3211
35
37
41
35
37
33
41
41
28
23
23
23
23
23
23
23
23
29
29
29
29
29
24
29
29
29
23
23
23
23
23
33
24
24
24
37
35
37
37
35
37
23
24
29
39
39
29
29
39
39
39
39
35
37
35
37
29
35
37
37
35
37
37
35
37
33
33
33
33
33
33
33
35
37
33
35
37
33
16
19
3212
3213
3214
3215
3215
3216
3217
3218
3219
3220
3221
3222
3223
3224
3225
3226
3227
3228
3229
3230
3232
3233
3234
3235
3236
3237
3238
3239
3240
3241
3243
3244
3245
3246
3247
3248
3248
3249
3249
3251
3252
3253
3254
3255
3256
3257
3258
3258
3259
3260
3261
3262
3262
3263
3264
3264
3265
3266
3266
3267
3267
3268
3268
3269
3269
3270
3270
3271
3272
3272
3273
3274
3274
3277
3277
3278
3279
3280
28
28
28
28
30
28
28
28
28
28
28
28
28
28
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
33
24
24
33
33
35
37
30
31
24
24
24
24
24
24
24
30
31
24
24
27
31
33
33
30
31
30
30
31
30
31
30
31
30
31
30
31
31
30
31
31
30
31
30
31
30
31
30
17
1
2
12
15
10
13
11
1
3
5
10
10
1
9
14
14
17
2
8
25
3281
3282
3282
3283
3283
3284
3284
3285
3286
3287
3287
3297
3298
3299
3300
3301
3302
3303
3313
3314
3329
3330
3352
3353
3354
3355
3356
3357
3358
3362
3363
3365
3366
3367
3368
3369
3370
3371
3371
3372
3373
3374
3375
3376
3377
3378
3379
3380
3381
3382
3383
3384
3385
3391
3392
3396
3397
3398
3399
3400
3401
3402
3403
3404
3405
3406
3407
3408
3409
3410
3411
3412
3413
3414
3415
3416
3417
3424
3425
31
30
31
30
31
30
31
31
31
30
31
37
37
24
35
37
37
24
39
39
28
25
23
23
23
23
23
23
23
24
24
24
24
24
24
24
33
35
37
35
37
37
24
24
23
23
23
23
23
23
24
23
24
27
27
27
10
6
7
12
18
15
23
25
9
8
13
14
17
3
10
11
35
46
23
37
18
30
1
6
22
15
I
8
42
39
36
14
13
49
48
50
15
5
II
13
2
26
40
2
20
23
18
12
51
10
20
44
24
23
22
6
38
6
II
16
13
10
9
1
27
29
24
26
19
21
21
11
5
17
24
21
30
22
23
27
28
20
15
3
2
7
6
22
24
20
21
19
4
9
9
9
32
19
20
3
7
16
19
19
15
18
26
8
11
12
5
5
19
8
8
2
2
25
27
22
24
13
6
2
2
5
1
1
2
4
10
38
5
24
31
18
53
28
30
34
3
5
17
13
6
14
15
24
3
2
4
21
8
10
7
25
3
4
11
8
31
14
21
32
15
18
43
39
41
42
9
17
18
7
8
14
8
18
21
1
1
18
18
8
8
10
8
10
9
12
29
2
19
15
18
2
13
16
7
9
6
8
5
7
17
20
3
11
14
4
4
6
16
19
9
12
14
3
3
3
18
18
18
31
7
17
4
4
4
20
20
45
8
13
12
17
17
19
19
14
12
13
17
11
15
16
7
21
50
49
47
45
46
54
55
15
17
16
14
13
6
9
4
8
7
1
12
3
2
5
10
11
11
37
27
27
27
27
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
28
27
Limited Warranty Statement
Sakundiak Equipment Ltd. warrants each new Sakundiak Equipment Ltd. product to be free from defects
in material and workmanship. This warranty is applicable only for the normal service life expectancy of the
product or components, not to exceed twelve (12) consecutive months, or forty-five (45) days in the case
of commercial use, from the date of delivery of the new Sakundiak Equipment Ltd . product to the original
purchaser.
Genuine Sakundiak Equipment Ltd. replacement parts and components will be warranted for thirty (30)
days from the date of purchase, or the remainder of the original equipment warranty period, whichever
is longer. Under no circumstances will Sakundiak Equipment Ltd. cover any merchandise or components
thereof, which, in the opinion of Sakundiak Equipment Ltd., has been subjected to misuse, unauthorized
modifications, alteration, an accident or if repairs have been made with parts other than those obtainable
through Sakundiak Equipment Ltd.
Sakundiak Equipment Ltd. in no way warrants engines, batteries, tires, or other trade accessories since
these items are warranted separately by their respective manufacturer. Our obligation under this warranty
shall be limited to repairing or replacing, free of charge to the original purchaser, any part that, in our
judgement, shall show evidence of such defect, provided further that such a part shall be returned within
thirty (30) days from date of failure to Sakundiak Equipment Ltd., routed through the dealer and distributor
from whom the purchase was made, transportation charges prepaid.
This warranty shall not be interpreted to render Sakundiak Equipment Ltd. liable for injury or damages of
any kind or nature to person or property. This warranty does not extend to the loss of crops, loss because of
delay in harvesting, or any expense or loss incurred for labor, substitute machinery, rental or for any other
reason. Except as set forth above, Sakundiak Equipment Ltd. shall have no obligation or liability of any kind
on account of any of its equipment and shall not be liable for special or consequential damages.
Sakundiak Equipment Ltd. makes no other warranty, expressed or implied, and, specifically, Sakundiak
Equipment Ltd. disclaims any implied warranty or merchantability or fitness for a particular purpose. Some
states or provinces do not permit limitations or exclusions of implied warranties, so the limitations or
exclusions in this warranty may not apply.
This warranty is subject to any existing conditions of supply which may directly affect our ability to
obtain materials or manufacture replacement parts. Sakundiak Equipment Ltd. reserves the right to make
improvements in design or changes in specifications at any time, without incurring any obligation to owners
of units previously sold. No one is authorized to alter, modify or enlarge this warranty nor the exclusion,
limitations and reservation.

SAKUNDIAK - Shortline Ag, Inc.

Transcription

Similar documents

VIBCO REPAIR KIT INSTRUCTIONS for BBS

DEMCO GRAIN CARTS

GRAIN CART 30TN ASCANELLI.cdr

12th Dec - Manor Green Primary School

Lisa Darsonval wears a lock and holds a key at the Santa Barbara

Demco Gravity Flow Wagons and Grain Carts

NEVER WELD UPSIDE DOWN NUTS AGAIN!

front suspension lift

PLANT HANGER.idw - Big Rivers, Ltd.