Quick manual scanCONTROL 2700 / 2800 - Micro

3. System Requirements
5. Controller Connections
-- Windows 2000 (Service Pack 4) / Windows XP
D
B
7. Driver Installation for Windows XP
A
Connect the controller to the PC using the 1394 FireWire
cable. If the installation doesn’t start automatically, search
for scanCONTROL in the device manager (Start > Control
Panel > System > Device Manager). scanCONTROL is
classified as camera device and is either located under
“Imaging Devices” or “Other Devices”. Right-click the
camera device and choose “Update Driver”.
-- Pentium III 800 MHz
-- System memory:
512 MB RAM for scanCONTROL 3D-View
256 MB RAM for scanCONTROL Demo-Software
-- Screen resolution: 1024 x 768
C
Please note the sequence for installation:
1. Hardware installation of the IEEE1394 interface
2. Software installation
3. Hardware setup
1. Connect the sensor cable to jack A
2. Connect the controller to the power supply (jack B)
3. Use the IEEE1394 FireWire cable and one of the jacks
C (any can be used) to connect the controller to the PC
4. Turn around the key D to switch the laser on
4. scanCONTROL driver installation
6. Sensor Mounting
scanCONTROL2700
4. Software Installation
1
1
Please insert the scanCONTROL Demo-CD into your
1
CD-ROM drive. The following dialog will appear to guide
you through the software installation.
1
Mark “No, not this time” and click on “Next”.
1
1
A
1
B
2
1
C
1
1
1
A. Read the installation guide
B. Install the software
C. Detailed information in the online manuals
1
2
2
scanCONTROL2800
The sensor can be mounted in two different ways:
1. with three M4 threaded holes, 5 mm deep
2. with three through holes dia. 4.5 mm
Select “Install from a list or specific location (Advanced)”
and click “Next”.
7. Driver Installation for Windows XP
8. First Profile
scancontrol 2700/2800
Quick Manual
Hardware and Driver Installation
Select “Don’t search. I will choose the driver to install.”
and click “Next”.
On the left side you can adjust the settings for your measurement task, the right side shows the profile data and
information about the measurement.
9. How to access Profile Data
Profile data of scanCONTROL can be accessed via:
-- DCAM standard v.1.30 for digital cameras via
IEEE 1394 FireWire interface
-- SDK for fast application integration (C, C++, C# and
others
-- CMU-Module for application development with
ICONNECT
Select the driver “CMU 1394 Digital Camera Device” and
click “Next”.
For details refer to the enclosed online manuals.
The “Hardware Installation” dialog will then appear.
Click on “Continue Anyway” to confirm this dialog.
10. Further Information
In the next dialog click “Finish” to end the driver
installation.
8. First Profile
If the demo software shows the error message “No LLT
found on the IEEE 1394-Bus” in the status line, please
check the installed driver in the device manager (Start >
Control Panel > System > Device Manager).
X9751109.01-B010069HDR
Now start the scanCONTROL Demo-Software. Click on
“Display Profile” in the main window.
1. What is scanCONTROL?
The measuring system scanCONTROL 2700/2800 is
designed for use in industrial applications and is characterized by high speed and high accuracy of measurement.
The scanCONTROL Demo-Software visualizes profiles and
helps you to find the correct parameters for your measurement task. This quick manual shows you how to install the
Demo-Software and the correct drivers to get your first
profile data.
2. Delivery
scanCONTROL2700:
scanCONTROL2800:
-- 1 sensor LLT2700
with integrated controller
-- 1 sensor LLT2800
Please refer to
-- the enclosed online manuals
-- 1 instruction manual
-- 1 instruction manual
-- the section “Status and Error Messages” and “Notes” in
the scanCONTROL Demo-Software manual
-- 1 power supply cable
PC2700-4.5
-- 1 power supply cable
PC2800-3
-- 1 scanCONTROL Demo-CD
-- 1 scanCONTROL Demo-CD
-- 1 calibration protocol
-- 1 IEEE 1394 FireWire cable
www.micro-epsilon.com
MICRO-EPSILON Messtechnik GmbH & Co. KG
94496 Ortenburg, Germany, Tel. +49 (0) 85 42/1 68-0
*X9751109.01-B01*
-- 1 controller
-- 1 key for the key switch
-- 1 calibration protocol