14, 16, and 18 Long Arm Radial Saws

(Models 33-400, 33-401, 33-402, 33-403,
33-410, 33-411, 33-412, 33-413,
33-420, 33-421, 33-422, 33-423)
PART NO. 424-03-651-0019 - 06-20-05
Copyright © 2004 Delta Machinery
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-800-223-7278 (In Canada call 1-800-463-3582).
INSTRUCTION MANUAL
14", 16", and 18"
Long Arm Radial Saws
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ADDITIONAL SPECIFIC SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
CARTON CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
SERVICE CENTER LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .back cover
IMPORTANT SAFETY INSTRUCTIONS
Read and understand all warnings and operating instructions before using any tool or equipment. When
using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury.
Improper operation, maintenance or modification of tools or equipment could result in serious injury and property
damage. There are certain applications for which tools and equipment are designed. Delta Machinery strongly
recommends that this product NOT be modified and/or used for any application other than for which it was designed.
If you have any questions relative to its application DO NOT use the product until you have written Delta Machinery
and we have advised you.
Online contact form at www.deltamachinery.com
Postal Mail: Technical Service Manager
Delta Machinery
4825 Highway 45 North
Jackson, TN 38305
(IN CANADA: 125 Mural St. Suite 300, Richmond Hill, ON, L4B 1M4)
Information regarding the safe and proper operation of this tool is available from the following sources:
Power Tool Institute
1300 Sumner Avenue, Cleveland, OH 44115-2851
www.powertoolinstitute.org
National Safety Council
1121 Spring Lake Drive, Itasca, IL 60143-3201
American National Standards Institute, 25 West 43rd Street, 4 floor, New York, NY 10036 www.ansi.org
ANSI 01.1Safety Requirements for Woodworking Machines, and
the U.S. Department of Labor regulations www.osha.gov
SAVE THESE INSTRUCTIONS!
2
SAFETY GUIDELINES - DEFINITIONS
It is important for you to read and understand this manual. The information it contains relates to protecting YOUR
SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may
result in property damage.
CALIFORNIA PROPOSITION 65
SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER
CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
· lead from lead-based paints,
· crystalline silica from bricks and cement and other masonry products, and
· arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with approved safety equipment, always wear NIOSH/OSHA
approved, properly fitting face mask or respirator when using such tools.
3
GENERAL SAFETY RULES
READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE
USING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in electric shock,
fire, and/or serious personal injury or property damage.
IMPORTANT SAFETY INSTRUCTIONS
1. FOR YOUR OWN SAFETY, READ THE INSTRUCTION
MANUAL BEFORE OPERATING THE MACHINE.
Learning the machine’s application, limitations, and
specific hazards will greatly minimize the possibility of
accidents and injury.
14.
2. WEAR EYE AND HEARING PROTECTION.
ALWAYS USE SAFETY GLASSES. Everyday
eyeglasses are NOT safety glasses. USE CERTIFIED
SAFETY EQUIPMENT. Eye protection equipment
should comply with ANSI Z87.1 standards. Hearing
equipment should comply with ANSI S3.19
standards.
15.
3. WEAR PROPER APPAREL. Do not wear loose
clothing, gloves, neckties, rings, bracelets, or other
jewelry which may get caught in moving parts. Nonslip
footwear is recommended. Wear protective hair
covering to contain long hair.
4. DO NOT USE THE MACHINE IN A DANGEROUS
ENVIRONMENT. The use of power tools in damp or
wet locations or in rain can cause shock or
electrocution. Keep your work area well-lit to prevent
tripping or placing arms, hands, and fingers in danger.
5. MAINTAIN ALL TOOLS AND MACHINES IN PEAK
CONDITION. Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and changing
accessories. Poorly maintained tools and machines can further
damage the tool or machine and/or cause injury.
6. CHECK FOR DAMAGED PARTS. Before using the
machine, check for any damaged parts. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, and any other conditions that may
affect its operation. A guard or any other part that is
damaged should be properly repaired or replaced.
Damaged parts can cause further damage to the
machine and/or injury.
7. KEEP THE WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
8. KEEP CHILDREN AND VISITORS AWAY. Your shop is a
potentially dangerous environment. Children and visitors can
be injured.
9. REDUCE THE RISK OF UNINTENTIONAL STARTING.
Make sure that the switch is in the “OFF” position
before plugging in the power cord. In the event of a
power failure, move the switch to the “OFF” position.
An accidental start-up can cause injury.
10. USE THE GUARDS. Check to see that all guards are
16.
17.
18.
19.
20.
21.
22.
23.
24.
in place, secured, and working correctly to reduce
the risk of injury.
11. REMOVE ADJUSTING KEYS AND WRENCHES
BEFORE STARTING THE MACHINE. Tools, scrap
pieces, and other debris can be thrown at high speed,
causing injury.
12. USE THE RIGHT MACHINE. Don’t force a machine or
an attachment to do a job for which it was not
designed. Damage to the machine and/or injury may
result.
13. USE RECOMMENDED ACCESSORIES. The use of
accessories and attachments not recommended by
4
Delta may cause damage to the machine or injury to the
user.
USE THE PROPER EXTENSION CORD. Make sure
your extension cord is in good condition. When using
an extension cord, be sure to use one heavy enough to
carry the current your product will draw. An undersized
cord will cause a drop in line voltage, resulting in loss of
power and overheating. See the Extension Cord Chart
for the correct size depending on the cord length and
nameplate ampere rating. If in doubt, use the next
heavier gauge. The smaller the gauge number, the
heavier the cord.
SECURE THE WORKPIECE. Use clamps or a vise to hold
the workpiece when practical. Loss of control of a
workpiece can cause injury.
FEED THE WORKPIECE AGAINST THE DIRECTION OF
THE ROTATION OF THE BLADE, CUTTER, OR ABRASIVE
SURFACE. Feeding it from the other direction will cause
the workpiece to be thrown out at high speed.
DON’T FORCE THE WORKPIECE ON THE MACHINE.
Damage to the machine and/or injury may result.
DON’T OVERREACH. Loss of balance can make you
fall into a working machine, causing injury.
NEVER STAND ON THE MACHINE. Injury could occur if the
tool tips, or if you accidentally contact the cutting tool.
NEVER LEAVE THE MACHINE RUNNING UNATTENDED.
TURN THE POWER OFF. Don’t leave the machine until it
comes to a complete stop. A child or visitor could be injured.
TURN THE MACHINE “OFF”, AND DISCONNECT THE
MACHINE FROM THE POWER SOURCE before installing
or removing accessories, before adjusting or changing
set-ups, or when making repairs. An accidental start-up
can cause injury.
MAKE YOUR WORKSHOP CHILDPROOF WITH
PADLOCKS, MASTER SWITCHES, OR BY
REMOVING STARTER KEYS. The accidental start-up
of a machine by a child or visitor could cause injury.
STAY ALERT, WATCH WHAT YOU ARE DOING, AND
USE COMMON SENSE. DO NOT USE THE
MACHINE WHEN YOU ARE TIRED OR UNDER THE
INFLUENCE
OF
DRUGS,
ALCOHOL,
OR
MEDICATION. A moment of inattention while operating
power tools may result in injury.
USE OF THIS TOOL CAN GENERATE
AND DISBURSE DUST OR OTHER
AIRBORNE PARTICLES, INCLUDING WOOD DUST,
CRYSTALLINE SILICA DUST AND ASBESTOS DUST.
Direct particles away from face and body. Always
operate tool in well ventilated area and provide for
proper dust removal. Use dust collection system
wherever possible. Exposure to the dust may cause
serious and permanent respiratory or other injury,
including silicosis (a serious lung disease), cancer, and
death. Avoid breathing the dust, and avoid prolonged
contact with dust. Allowing dust to get into your mouth
or eyes, or lay on your skin may promote absorption of
harmful material. Always use properly fitting
NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure, and wash exposed
areas with soap and water.
ADDITIONAL SPECIFIC SAFETY RULES
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.
11. KEEP ARMS, HANDS, AND FINGERS away from
the blade.
12. NEVER REACH around the saw blade.
13. NEVER PERFORM a “crossed arm” operation.
14. PROPERLY SUPPORT LONG OR WIDE
workpieces.
15. NEVER START THE MACHINE with the workpiece
against the blade.
16. FOLLOW ALL RIPPING WARNINGS on machine.
NEVER FEED THE WORKPIECE into the antikickback end of the machine. FEED WORKPIECE
against blade rotation.
17. USE PUSH STICK(S) for ripping a narrow
workpiece.
18. RETURN THE CUTTERHEAD to the full rear
position behind the fence after each crosscut
operation.
19. REPAIR OR REPLACE damaged fence or work
table.
20. NEVER PERFORM LAYOUT, ASSEMBLY, or set-up
work on the table/work area when the machine is
running.
21. TURN THE MACHINE “OFF” AND DISCONNECT
THE MACHINE from the power source before
installing or removing accessories, before adjusting
or changing set-ups, or when making repairs.
22. TURN THE MACHINE “OFF”, disconnect the
machine from the power source, and clean the
table/work area before leaving the machine. LOCK
THE SWITCH IN THE “OFF” POSITION to prevent
unauthorized use.
23. ADDITIONAL INFORMATION regarding the safe
and proper operation of power tools (i.e. a safety
video) is available from the Power Tool Institute,
1300 Sumner Avenue, Cleveland, OH 44115-2851
(www.powertoolinstitute.com). Information is also
available from the National Safety Council, 1121
Spring Lake Drive, Itasca, IL 60143-3201. Please
refer to the American National Standards Institute
ANSI 01.1 Safety Requirements for Woodworking
Machines and the U.S. Department of Labor OSHA
1910.213 Regulations.
1. DO NOT OPERATE THIS MACHINE UNTIL it is
assembled and installed according to the
instructions.
2. OBTAIN ADVICE from your supervisor, instructor,
or another qualified person if you are not familiar
with the operation of this machine.
3. FOLLOW ALL WIRING CODES and recommended
electrical connections.
4. USE THE GUARDS WHENEVER POSSIBLE.
Check to see that they are in place, secured, and
working correctly.
5. ENSURE THAT END PLATES ARE SECURELY
FASTENED TO TRACK ARM prior to use.
6. TIGHTEN ALL CLAMP HANDLES prior to use
except for the motor carriage clamp. Tighten this
clamp only for ripping operations.
7. AVOID KICKBACK BY:
A. keeping blade sharp and free of rust and pitch.
B. keeping blade parallel to the fence when
ripping.
C. using anti-kickback fingers when ripping.
Lower the guard on the infeed end and adjust
the anti-kickback attachment properly.
D. never ripping a workpiece that is twisted or
warped, or does not have a straight edge to
guide along the fence.
E. never sawing a large workpiece that cannot be
controlled.
F. never sawing a workpiece with loose knots or
other flaws in the workpiece.
8. REMOVE CUT-OFF PIECES AND SCRAPS from
the table before starting the saw. The vibration of
the machine may cause them to move into the saw
blade and be thrown out. After cutting, turn the
machine off. Wait for the blade to come to a
complete stop before removing any debris.
9. NEVER perform “free-hand” operations.Use the
fence to position and guide the workpiece.
10. KEEP FENCE HALVES adjusted close to the blade
for proper work support.
SAVE THESE INSTRUCTIONS.
Refer to them often and use them to instruct others.
5
POWER CONNECTIONS
The Long Arm Radial Saws are not supplied with a power cord. They must be permanently connected to the building
electrical system and all wiring must be done by a qualified electrician and conform to the National Electric Code and all local
codes and ordinances. Since they are permanently connected, extension cords cannot be used.
MOTOR SPECIFICATIONS
Your machine is wired for 230V, 60HZ alternating current. Check the spec plate on the motor for the horsepower rating,
whether the motor is dual voltage and to determine if your machine is single or three phase.
GROUNDING INSTRUCTIONS
A separate electrical circuit should be used for your machines. This circuit should not be less than #12
wire and should be protected with a 20 Amp time lag fuse.
* THREE PHASE OPERATION: Three phase machines are not supplied with a power cord and must be permanently
connected to a building’s electrical system. Extension cords can’t be used with a three phase machine.
* LVC MAGNETIC MOTOR CONTROL: Your radial arm saw was shipped with a Low Voltage Magnetic Motor Control
System. Please refer to its instruction manual for installation guidance.
* 460 VOLT OPERATION: If your saw has a dual voltage motor (230/460 volts), and you desire the machine to run at 460
volts, the re-wiring must be done by a qualified electrician and conform to the National Electric Code and all local codes
and ordinances.
FUNCTIONAL DESCRIPTION
FOREWORD
Deltas Long Arm Radial Saws have a totally enclosed, fan-cooled motor with electro-mechanical blade brake, 18", 16",
or 14" blade guard with anti-kickback attachment, retractable leaf guard, cutterhead return attachment, cuttinghead
clamp knob, adjustable crosscut stop, and steel legs.
NOTICE: THE PHOTO ON THE MANUAL COVER ILLUSTRATES THE CURRENT PRODUCTION MODEL. ALL OTHER
ILLUSTRATIONS CONTAINED IN THE MANUAL ARE REPRESENTATIVE ONLY AND MAY NOT DEPICT THE ACTUAL COLOR,
LABELING OR ACCESSORIES AND ARE INTENDED TO ILLUSTRATE TECHNIQUE ONLY.
CARTON CONTENTS
5
1
6
7
2
1
4
6
8
7
9
4
8
2
3
3
12
10
11
5
13
9
1.
2.
3.
4.
5.
6.
7.
Fig. 1
Blade Guard (1)
8.
Angle Support (3)
9.
Blade (1)
10.
Cross Stop (1)
11.
Track-Arm Lock
Handle (1)
12.
1-1/16" Open End
13.
Wrench (1)
Spanner Wrench with a
1-5/8" Box End (1)
Roller Head Wrench (1)
Anti-kickback Rod (1)
Cable Clamp (1)
Elevating Crank Handle
(1)
Starter Box Bracket (1)
Cutterhead Return
Spring (1)
1.
2.
3.
4.
5.
6.
7.
8.
9.
6
Fig. 1a
3/8-16x1" Hex Head Screw (12)
1/4-20x7/8" Round Head Screw (15)
1/2-20x1/2" Hex Head Screw (4)
3/8" Flat Washer (12)
9/32" Flat Washer (15)
3/8" Lockwasher (12)
1/4" Lockwasher (4)
3/8-16 Hex Nut (12)
1/4-20 Hex Nut (1)
GUIDE TO PARTS
The following is an explanation of the operating controls of the Delta 14", 16" and 18" Radial Arm Saws. All users will
benefit by knowing how to set and operate the controls for all cutting operations. To avoid the possibility of damage
to the machine and/or injury to the operator, all user’s should become familiar with the operations and the controls
before turning the machine “ON’.
A
B
C
M
E
F
Fig. 2
Fig. 3
A - TRACK-ARM CLAMP HANDLE Fig. 2. Controls
swing of track-arm for all miter cutting operations.
Locks track-arm at any angle for the full 180° rotation.
To rotate track-arm, loosen clamp handle and rotate
arm. The arm will stop at the 0° and 45° positions right
and left. To move the arm past these points the trackarm index knob (B) must be pulled out.
F - ELEVATING CRANK HANDLE Fig. 3. Controls the
depth of cut in all operations. Turning the crank handle
raises or lowers the over-arm.
G - CUTTINGHEAD CLAMP KNOB Fig. 3. Locks
cuttinghead at any position on the track-arm. When
ripping the cutting clamp knob must be tight.
H - CROSS-CUT STOP Fig. 3. Prevents unnecessary
travel of the cuttinghead on the track-arm. It is
especially useful when performing repetitive operations.
Clamp the stop to the side of the track-arm at a position
which will stop the cuttinghead travel as soon as the
blade cuts through the workpiece.
B - TRACK-ARM INDEX KNOB Fig. 2. Locates 0° and
45° miter position, right and left, of the track-arm
C - YOKE INDEX KNOB Fig. 2. Locates each 90°
position of the yoke for ripping or cross-cutting
operations. When rotating the yoke, the yoke clamp
handle (D) must first be loose.
J - BEVEL INDEX KNOB Fig. 3. Locates 0° and 45°
and 90° positions of the motor when bevel cutting.
When tilting the motor for bevel cutting, the bevel clamp
handle (K) must first be loose.
D - YOKE CLAMP HANDLE Fig. 3. The yoke clamp
handle must be loose when rotating the yoke to the rip
or cross-cut position.
E - ANTI-KICKBACK DEVICE Fig. 2. When ripping,
the yoke is positioned and clamped so that the blade is
parallel to the fence. The rear of the blade guard is
lowered until it almost touches the workpiece. The antikickback rod is then lowered so that the fingers catch
and hold the workpiece. Never rip from the antikickback end of the blade guard.
K - BEVEL CLAMP HANDLE Fig. 3. Controls tilt of
motor for bevel cutting operations. Locks motor at any
desired angle on the bevel scale.
L - TABLE CLAMP KNOBS. Fig 3. Allows the operator
to quickly set the desired fence position.
M - CUTTINGHEAD RETURN ATTACHMENT Fig. 2.
Automatically returns the cuttinghead to the rear of the
track-arm after completion of the cut.
UNPACKING AND CLEANING
Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from
all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone,
gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household
floor paste wax.
7
ASSEMBLY
FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE
MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL.
ASSEMBLY TOOLS REQUIRED
*
*
*
1/16" Open End Wrench (supplied)
Roller Head Wrench (1)
9/16” and 3/8” open end or socket wrenches (not
included)
ASSEMBLY TIME ESTIMATE-4 to 6 hours
SELECTING FLOOR SPACE
Fig. 4
Before unpacking, determine exactly where you want to
set up the machine. It is highly desirable to locate the
machine against the wall where it will be out of the way
and will actually facilitate material handling through the
shop.
UNPACKING AND ASSEMBLING
LEGS TO BASE
IMPORTANT: Remove the carton from the machine.
Remove bolts that fasten the machine to the skid.
F
IMPORTANT: To gain access to the four bolts that
fasten the saw to the wooden shipping skid, loosen two
table lock knobs (A) Fig. 4. Remove fence (B), angled
front table board (C) and at least two table boards (D).
Do not remove the packing material around the motor at
this time.
E
G
H
Fig. 5
Mechanically lift the machine using a forklift and lifting
straps, and support the machine. Attach the four steel
legs (E) Fig. 5, to each corner of the base using twelve
3/8-16x1" hex head screws (F), 3/8" flat washers (G),
and 3/8" lockwashers (I) and 3/8-16 hex nuts (H).
Remove the packing material from around the motor.
The motor will be positioned on the table as shown in
Fig. 4.
Fig. 6
ELEVATING CRANK HANDLE
Assemble elevating crank handle (A) Fig. 6 to rod in
front of base using the roll pin (B).
TRACK-ARM LOCK
Assemble track-arm lock handle (A) to the overarm (Fig.
7), and tighten set screw (B). Lock handle (A) should be
tight when in the position shown in Fig. 7, and loose
when pulled forward and resting against stop (C).
8
Fig. 7
CUTTINGHEAD AND CROSS-CUT
STOP TO TRACK-ARM
1. Remove two screws (A) and end cap (B) from trackarm, Fig. 8.
2. Hold cuttinghead assembly (D) Fig. 9, with both
hands and insert the ball bearings (E) into the trackarm, as shown. Push cuttinghead all the way onto
track-arm and tighten clamp knob (F).
3. Assemble cross-cut stop (C) to the track-arm (Fig.
10).
Fig. 8
F
4. Replace end cap (B) that was removed in STEP 1
(Fig. 11).
E
D
Fig. 9
Fig. 10
Fig. 11
9
STARTER BOX TO BASE
1. Assemble bracket (A) to the bottom of the right side
of saw base, (Fig. 12), using the 1/4-20x1/2" hex head
screw (B), 1/4" lockwasher (D), and 1/4-20 nut (E).
2. Assemble the starter box (B) Fig. 13 to the right side
of the base by inserting the three1/4-20x1/2" hex head
screws (C) with 1/4" lock-washers, through the two
holes in the base and the hole in the bracket and into the
three 1/4-20 weld nuts in the back of the starter box. A
cable clamp is supplied to attach the power cord to saw
frame.
3. Fig. 14 illustrates the starter box assembled to the
base.
D
E
B
Fig. 12
Fig. 14
Fig. 13
TABLE BOARDS AND FENCE
1. Assemble loose table boards and fence (A) Fig. 15, on the table brackets.
2. Assemble three angle supports (B) Fig. 15 to the fixed front table board (C) using nine 1/4-20x7/8" round head
screws and 9/32" flat washers (D).
Fig. 16
Fig. 15
3. Fig. 16 illustrates three angle supports (B) assembled
to the fixed table board (C).
4. Place the smaller angled table board (D) Fig. 16, on
the angle supports (B) and fasten with six 1/420x7/8" round head screws and 9/32" flat washers
shown at locations (E) Fig. 17.
Fig. 17
10
ADJUSTING TABLE TOP
PARALLEL TO TRACK-ARM
C
For accurate work the track-arm must be parallel to the
table top at all points.
To check and adjust:
1. Move the motor and cuttinghead assembly (A) to
the vertical position (Fig. 18). Position saw arbor (B)
Fig. 18, so that it is approximately in the center of
the front table board. Push track-arm clamp handle
(C) Fig. 18 to the rear to secure track-arm and
tighten cuttinghead clamp knob (G) Fig. 5.
A
B
Using the spanner wrench (E) Fig. 18 as a feeler gauge,
raise or lower track-arm by turning elevating handle (F)
Fig. 19 until saw arbor (B) just touches wrench (E). DO
NOT RAISE OR LOWER TRACK-ARM ANY FURTHER
UNTIL LEVELING ADJUSTMENT IS COMPLETED.
E
Fig. 18
2. Move cuttinghead (A) so that the saw arbor (B) Fig.
19 is at the left front table, as shown. Make sure
track-arm clamp lever and cuttinghead lock knob
are tight. Using the spanner wrench (E) Fig. 19 as a
feeler guage check to see if an adjustment is
necessary. To lower the table, loosen nut (G) and
tighten nut (H) Fig. 19. To raise the table, reverse this
adjustment. Check table at points (J) and (K) and
adjust if necessary. Check table on right side in the
same manner.
F
Fig. 19
BLADE GUARD AND ANTIKICKBACK DEVICE
1. Loosen set screw (E) Fig. 22. Remove arbor nut (A)
and outer blade flange (B).
Fig. 22
2. Install blade on the saw arbor with teeth of blade
pointing downward when viewed from front of saw,
as shown in Fig. 23. Place the recessed end of
blade flange (B) Fig. 23, against the blade, and
thread the arbor nut (A) onto the arbor.
Fig. 23
11
3.
4.
5.
6.
7.
IMPORTANT: To prevent arbor nut from spinning when blade stops, place the 1-1/16" wrench (C) Fig. 23 on
flats of arbor and firmly tighten arbor nut (A) with the 1-5/8" box end spanner wrench (D) (left handed
thread). Firmly tighten set screw (E).
Remove screw (F) Fig. 25 that attaches inside leaf guard (G) to rear of blade guard (H).
Assemble blade guard (H) Fig. 25, to motor housing. Position bracket (J) over motor housing and blade guard
flange (K) and loosely fasten 1/2-13 hex nut (L) with wrench supplied.
Place leaf guard (G) Fig. 26 in place on blade guard (H) and fasten with special shoulder bolt (F).
Assemble anti-kickback rod (M) Fig 27 to blade guard (H), and fasten in place with thumb screw (N). NOTE: It will
be necessary to tilt the blade guard (H) to the rear in order to assemble anti-kickback rod (M). Tighten nut (L) Fig.
25.
L
J
K
G
F
H
Fig. 24
Fig. 25
H
F
G
Fig. 26
Fig. 27
CUTTERHEAD RETURN SPRING
1. Remove fence from the table and return the cuttinghead assembly to rear of track arm. Rotate track arm 90
degrees to the right.
2. Remove left screw (B) Fig. 28 from yoke assembly.
3. Assemble reel (C) Fig. 29 to yoke assembly (D) and fasten with screw (B), which was removed in STEP 2.
B
B
C
D
Fig. 29
Fig. 28
12
4.
5.
Attach eyelet (H) Fig. 30 of cable assembly (C) to
"S" bracket (E).
NOTE: To prevent premature wear of return reel
cable, position the return reel so that the cable does
not rub against the wall of the return reel.
E
C
H
Fig. 30
OPERATION
OPERATIONAL CONTROLS AND ADJUSTMENTS
STARTING AND STOPPING SAW
1. The on/off switch (A) Fig. 30A is located on the front
of the saw. To turn the machine on, push the “START”
button.
2. To turn the machine “OFF”, push the “STOP” button.
A
MAKE SURE THAT THE SWITCH IS IN
THE “OFF” POSITION BEFORE WIRING
THE MACHINE. IN THE EVENT OF A POWER FAILURE,
PUSH THE STOP BUTTON. AN ACCIDENTAL STARTUP CAN CAUSE INJURY.
Fig. 30A
LOCKING SWITCH IN “OFF” POSITION
IMPORTANT: When the machine is not in use, the switch
should be locked in the “OFF” position to prevent
unauthorized use, using a padlock (B) Fig. 30B with a 3/16"
diameter shackle.
B
Fig. 30B
Every Delta Radial Arm Saw is thoroughly tested, inspected and accurately aligned before leaving the factory and,
when delivered, is ready for operation after it is assembled. However, regardless of the care with which this or any piece
of fine machinery is manufactured, inspected and shipped, it is possible that rough handling in shipment, or wear over
a period of time may make minor adjustments necessary.
ALWAYS DISCONNECT MACHINE FROM POWER SOURCE BEFORE MAKING ANY ADJUSTMENTS.
13
TAKING SIDE MOTION OUT OF OVER-ARM
DISCONNECT MACHINE FROM POWER
SOURCE.
1.
2.
3.
4.
Loosen hex nuts (A) and gib adjusting screws (B)
and (C) Fig. 31.
Loosen nuts (D) Fig. 31, and adjust bolts (E), so that
base wraps around column securely. If column is
tight in base, turn bolts (E) clockwise to loosen.
IMPORTANT: Turning bolts (E) clockwise will open
the base jaws, while turning bolts (E) counterclockwise and tightening nuts (D) will close the base
jaws. Check elevation by turning crank handle,
making sure the column moves up and down
without binding.
Tighten screws (B) Fig. 31, against the column gib
until all side motion disappears in over-arm.
Securely lock hex nuts (A) while holding screws (B)
and tighten screw (C).
Fig. 31
TIGHTENING YOKE AGAINST BEARING CARRIAGE
DISCONNECT MACHINE FROM POWER
SOURCE.
After extended use "play" may develop between yoke
(C) Fig. 32, and bearing carriage (B). To reduce "play":
D
1. Remove guard and saw blade.
2. Remove end plate and cross cut stop from trackarm.
3. Remove yoke assembly from track-arm and place
yoke assembly (C) Fig. 32 on saw table.
4. Pull yoke clamp handle (A) to the position shown in
Fig. 32 to loosen, and loosen set screw (D) one turn
only.
5. Turn nut (E) Fig. 32 clockwise until "play" between
the yoke (C) and bearing carriage (B) is removed.
Then tighten set screw (D),Fig. 32
6. Tighten yoke clamp handle (A) Fig. 32 by moving it
forward, and reassemble yoke (C) assembly to
track-arm.
Fig. 32
ADJUSTING BALL BEARINGS AGAINST TRACK RODS
The carriage is mounted on four double row, sealed ball bearings, two on fixed shafts. To adjust the ball bearings
against the track rods:
DISCONNECT MACHINE FROM POWER SOURCE.
1.
Remove end plate from track-arm, loosen clamp knob (A) Fig. 33, and move cuttinghead (B) to the front of the
track-arm, then tighten clamp knob (A).
2.
Loosen two set screws, one of which is shown at (C) Fig. 33, that lock both front and rear bearing eccentric shafts.
The other screw is at the rear of the carriage.
3.
Rotate yoke (B) Fig. 33 until hole in yoke is under either eccentric shaft (D).
4.
Place roller head wrench (E) over hex nut (G) that locks shaft (D) Fig. 33, and loosen hex nut. Repeat this procedure
at rear bearing.
5.
Insert hex wrench (F) into eccentric shaft (Fig. 33), and turn until all "play" is removed between bearing (D) and
track rods. Repeat this procedure for the rear bearing.
6.
Tighten hex nuts with wrench (E) and lock set screws (C) with wrench at both bearings (Fig. 33). Replace end cap
on track-arm.
14
ADJUSTING TRACK RODS
Each track rod (A, B, C, D) Fig. 34 can be adjusted
individually to present a new bearing surface. Adjust the
track rods one at a time as follows:
DISCONNECT MACHINE FROM POWER
SOURCE.
1. Remove end cap (E) Fig. 35, cross-cut stop (F) and
cutterhead assembly (G), from the track-arm (Fig.
35).
G
Fig. 33
2. Loosen series of top screws (H) Fig. 35 just enough
to release holding action on the top left track rod (A)
Fig. 34. Insert screwdriver into slotted end of track
rod (A) Fig. 34, and turn slightly right or left.
Retighten all top screws (H) Fig. 35.
3. Bottom left track rod (B) Fig. 34 is adjusted in the
same manner by loosening series of bottom screws
(J) Fig. 35.
4. Adjust the right side track rods (C & D) Fig. 34 in the
same manner. NOTE: When adjusting bottom right
track rod (D) the rip scale must first be removed.
5. Reassemble the cutterhead assembly.
NOTE: After adjusting the track rods, check to see if
the blade is square to the table top.
Fig. 34
Fig. 35
15
ADJUSTING BLADE SQUARE WITH TABLE TOP
DISCONNECT MACHINE FROM POWER
SOURCE.
1.
Remove blade guard and place saw blade in cut-off
position over fixed portion of table.
2.
Place a square (A) Fig. 36, against saw blade. Be
sure square is on the table surface, and between
the gullets of the teeth, not against the saw teeth.
3.
Loosen bevel clamp handle (B) Fig. 36, and loosen
two screws (C).
4.
Tilt the motor assembly (D) Fig. 36, until square is
flush against saw blade and tighten bevel clamp
handle (B) Fig. 36 to hold position. Then tighten two
screws (C).
5.
If the above adjustment is not sufficient, remove
scale (E) Fig. 37, and loosen the two socket head
screws (F) located on each side of the center pivot
screw. Rotate motor for approximate adjustment
and retighten the two socket head screws (F).
6.
Replace scale plate (E) Fig. 37, and repeat STEPS 3
and 4 for final adjustment.
7.
Replace the guard.
Fig. 36
Fig. 37
ADJUSTING BEVEL CLAMP HANDLE
If the bevel clamp handle (A) Fig. 38 does not securely
lock the motor when the handle is in the locked position,
an adjustment can be made.
DISCONNECT MACHINE FROM POWER
SOURCE.
1. Place motor (B) Fig. 38, in a bevel cutting position
between positive stops, as shown, and place bevel
clamp handle (A) in the locked position, as shown.
2. Loosen nut (C) Fig. 38, and tighten bolt (D) until
motor is locked.
DO NOT OVER TIGHTEN BOLT (D).
3. While holding bolt (D) Fig. 38, tighten lock nut (C).
Fig. 38
ADJUSTING TRACK-ARM CLAMP HANDLE
When the track-arm clamp handle (A) Fig. 39 has to be
moved beyond the position shown to clamp the trackarm, an adjustment can be made as follows:
A
DISCONNECT MACHINE FROM POWER
SOURCE.
1. Move clamp handle (A) Fig. 39 to the rear as far as
it will go.
2. Loosen set screw (B) Fig. 39, remove clamp handle,
(A) and reposition handle (A) on stud. Move handle
to the rear until track-arm is completely locked.
Then tighten set screw (B).
B
16
Fig. 39
ADJUSTING SAW TRAVEL SQUARE WITH FENCE
Your radial saw is equipped with exclusive "Micro-Set" Miter Stops. This unique feature makes it possible to produce
accurate miter cuts and perfectly square cross-cuts at all times by individual adjustment of the three stop positions.
These stops are accurately adjusted at the factory. However, adjustments can be made if necessary.
Once the "Micro-Set" stops are set, you can be assured of quick, positive settings at the three positions.
Before determining if the "Micro-Set" stops require adjustment, check saw travel for squareness with table fence. To
do accurate work, saw travel must be 90 degrees to the fence. To check and adjust:
G
H
C
B
A
Fig. 40
DISCONNECT MACHINE FROM POWER
SOURCE.
1.
2.
3.
4.
5.
6.
Place a square (A) Fig. 40 against fence (B), and
lower cuttinghead (C) so that saw blade just clears
table top.
Pull cuttinghead (C) Fig. 40, along square (A). If saw
blade does not travel parallel to the square, the
following adjustment is necessary.
Remove cover plate (D) Fig. 41.
Locate center cap screw (E) Fig. 41 inside pivot
column and loosen slightly. Tap center cap screw (E)
sharply with a block of wood or insert a thin wooden
wedge inside the column to loosen the tapered plug
(F) Fig. 41 that is attached to the cap screw (E). It is
very important that the tapered plug (F) is loosened
before any further adjustment is made.
Loosen clamp handle (G) Fig. 40.
Using wrench on hex nut (H) Fig. 40, turn slightly to one side.
Fig. 41
CAUTION: Do not attempt to rotate completely. Notice that the entire track also moves.
7.
When saw blade tracks evenly against steel square, tighten clamp handle (G) Fig. 40 and center cap screw (E) Fig.
41.
8. Check pointer and adjust to 0 degrees, if necessary.
9. Replace cover plate (D) Fig. 41.
10. Right and left miter positions can be independently adjusted using the same procedure as above. If square is not
available, trial cuts can be made to determine if adjustment is necessary.
17
REMOVING "HEELING" IN SAW CUT
Even though the cuttinghead travel may be perfectly
aligned at 90 degrees to the fence, the blade itself may
not be 90 degrees or square with the fence, (Fig. 42).
This condition is known as "heeling."To check and
adjust:
DISCONNECT MACHINE FROM POWER
SOURCE.
1.
Cross-cut a board and see on which side of the cut
board saw teeth marks appear.
Fig. 42
2. If saw teeth marks appear on the right side, the back
end of the saw blade must be shifted toward left side.
3. Loosen yoke clamp handle (A) Fig. 43. Then loosen
both screws (B) Fig. 44, and turn yoke (C)
COUNTER-CLOCKWISE. If saw teeth marks
appear on left side of board, turn yoke (C)
CLOCKWISE.
Fig. 43
B
C
4. Tighten yoke clamp handle (A) Fig. 43 to hold
position and retighten screws (B) Fig. 44.
5. Make another test cut and repeat steps 1 through 5
until “heeling” is eliminated.
Fig. 44
ADJUSTABLE CROSS-CUT STOP
An adjustable cross-cut stop (A) Fig. 45 is provided to
prevent unnecessary travel of the cuttinghead on the
track-arm. It is especially useful when performing
repetitive operations. Clamp the stop to the side of the
track-arm at a position which will stop the cuttinghead
travel as soon as the blade cuts through the workpiece.
Fig. 45
18
ADJUSTING BLADE GUARD
DISCONNECT MACHINE FROM POWER
SOURCE.
On all ripping and plowing operations, the back part of
the blade guard is lowered so that it just clears the
material. This will prevent the material from being lifted
off the table. Also, lower the kickback rod (A) Fig. 46, so
that the kickback fingers are 1/8" below surface of
material. The kickback fingers will then come into
contact with the material preventing "kickback." Adjust
dust elbow (B) Fig. 46 to direct sawdust to rear of
machine.
Fig. 46
CHECKING AND ADJUSTING AUTOMATIC BRAKE
After a period of extended use, the automatic brake should be checked and adjusted if necessary to maintain proper
blade braking action.
NOTE: The blade stopping time should be a maximum of one second per one inch of the blade diameter.
To check the setting on the automatic brake:
DISCONNECT MACHINE FROM POWER SOURCE.
1.
2.
3.
4.
Remove four screws, three of which are shown at (A) Fig. 47, and remove fan cover (B) from the motor.
The air gap (D) Fig. 48, must be maintained between .008" and .012". Use a feeler gauge (C) to measure the gap.
If an adjustment is necessary, turn lock nut (F) Fig.48, until a proper gap setting of .010" is attained.
Replace fan cover that was removed in Step 2.
Fig. 48
Fig. 47
19
ADJUSTING TENSION ON CUTTINGHEAD RETURN ASSEMBLY
The cuttinghead return assembly is properly tensioned when there is just enough cable tension to return the
cuttinghead (A) Fig. 49, without excessive force, to the rear of the track arm (B) after completion of the cut. To adjust:
DISCONNECT MACHINE FROM POWER SOURCE.
1.
To INCREASE cable tension, turn adjustment dial (C), Fig. 49, clockwise.
2.
To DECREASE cable tension, pull back on cable tension release knob (D) Fig. 50, until the desired tension is
achieved.
B
C
D
D
A
Fig. 49
Fig. 50
WRENCH STORAGE BRACKETS
The Radial Arm Saw is supplied with three brackets (A)
Fig. 51, for storing wrenches when not in use.
Fig. 51
AUXILIARY TABLE BOARD FACING
To prevent repeated cutting into the table surface which will eventually cause the table to sag, an auxiliary table board
facing can be cut and fitted to the table. It can be made from 1/4″ plywood or particle board and should be cut to a
size that will exactly cover all of the table boards in front of the fence. The auxiliary table board facing should be placed
flat on the table and butted against the table fence. Fasten it to the table with a small brad or finish nail in each corner.
The life of the table boards will be greatly extended by the use of an auxiliary facing.The auxiliary facing can be
replaced as often as is necessary to protect the table.
USING A TABLE EXTENSION
When a table extension more than 24 inches long is attached to the saw, a sturdy outrigger support should be provided
or the stand or bench must be secured to the floor.
20
MACHINE USE
CROSS-CUTTING
Cross-cutting consists of supporting the workpiece
against the fence and pulling the saw blade through the
material at right angles to it.
When cross-cutting, the track arm should be indexed at
“0” and the track arm clamp handle tightened. The fence
should be clamped between the table boards. The saw
blade is to be to the left and behind the fence. The
workpiece is placed on the table and butted against the
fence. The saw blade should be clear of the fence and
table when the machine is turned on. Then the saw blade
is lowered until it lightly cuts into the table surface. The
operator should position himself a little to the left of the
machine for better visibility while cutting. Pull the saw
blade through the work, just far enough to cut it off, and
return the saw blade to its starting position. Turn tool off.
Fig. 52
and wait for the blade to stop before touching the cut-off
piece. The operator should always be sure to return the cutter-head carriage to the full rear position after each cross-cut
operation.
NOTE: When cross-cutting material more than 1″″ thick, the fence must be positioned immediately behind the fixed
front table board.
CROSS-CUT STOP
A block of wood placed at (B) Fig. 53 clamped to the
track arm with a small “C” clamp will prevent
unnecessary travel (T) of the cutting-head on the track
arm. This is especially useful when performing repetitive
operations. Clamp the block of wood to the right side of
the track arm at a position which will stop the cuttinghead travel as soon as the saw blade cuts through the
workpiece.
T
B
Fig. 53
MITER CUTTING
Miter cutting is similar to cross-cutting except the
workpiece is cut off at an angle (up to 45 degrees right or
left) rather than being cut off square. The settings and
operation are performed in the same manner as crosscutting except that the track arm is first positioned to the
desired angle on the miter scale before it is clamped in
place. The operator should position the hand holding the
workpiece on the opposite side to the direction of the
miter so the blade is pulled through the workpiece and
away from the hand. Fig. 54 shows a typical miter cutting
operation on the radial saw.
Fig. 54
21
COMPOUND MITER CUTTING
Compound miter cutting is performed in the same
manner as miter cutting except the saw blade is also tilted
to cut a bevel. The settings and operation are similar to
miter cutting except that the blade is first tilted to the
desired angle on the bevel scale before it is clamped in
place. Fig. 55 shows a compound miter cutting
operation on the radial saw.
RIPPING
IMPORTANT: In certain applications, it may be necessary
to use two push sticks, and/or featherboards. Also, if a
push stick or other feeding device is necessary to assist
in the feeding of material, make certain it is conveniently
located so it may be reached easily without having to
stretch or reach near the blade.
Ripping involves making a lengthwise cut through a board
along the grain. When ripping, the track arm is clamped at
“0” on the miter scale. The yoke is then positioned and
clamped so that the blade is parallel to the fence. When
feeding the material, one edge rides against the fence
while the flat side of the board rests on the table. The
guard should be lowered on the in-feed side until it almost
touches the workpiece (Figs. 56 and 57), to act as a
holddown. The splitter and anti-kickback fingers (A) Fig.
56 should be adjusted as described under the section
“ADJUSTING SPLITTER AND ANTI-KICKBACK
FINGERS” in this manual. The operators hands should
always be well away from and to the side of the blade.
When ripping narrow work, always use a push stick as
shown in Fig. 58 to push the work between the fence and
blade. The workpiece must have one straight edge to
follow the fence. If board is bowed, place hollow side
down. The cutting-head clamp knob should be securely
tightened for all ripping operations.
Fig. 55
A
Fig. 56
THE MATERIAL MUST NEVER BE FED
INTO THE OUTFEED END OF THE
BLADE GUARD.
OUT-RIPPING
B
Out-ripping involves all of the general conditions stated
above. The yoke is clamped at right angle to the track arm
with the blade guard facing the front of the machine. The
cutting-head is positioned on the out-rip scale to the
desired setting and clamped in position. The workpiece is
fed from the left side of the saw. Fig. 56 shows a typical
out-ripping operation on the radial saw.
Fig. 57
IN-RIPPING
In-ripping involves all of the general conditions stated
under RIPPING. The yoke is clamped at right angle to the
track arm with the blade guard facing the rear of the
machine. The cutting-head is positioned on the in-rip
scale to the desired setting and clamped in position. The
workpiece is fed from the right side of the saw. Fig. 57
shows a typical in-ripping operation on the radial saw.
WHEN RIPPING WORK LESS THAN FOUR INCHES WIDE, USE A PUSH STICK TO COMPLETE
THE FEED. (FIG. 58)
22
CONSTRUCTING A PUSH STICK
23
Fig. 58
1/2″ Squares
Cut here to push
1/4″ wood.
Cut here to push
1/2″ wood.
Notch to
help prevent
hand from slipping
Make from 1/2″ OR 3/4″ WOOD
or thickness less than
width of material to be cut.
PUSH STICK
When ripping work less than 4 inches wide, a push stick should be used to complete the feed and could easily be
made from scrap material by following the pattern shown in Fig. 58.
TROUBLESHOOTING GUIDE
For assistance with your tool, visit our website at www.deltamachinery.com for a list of service centers or call the
DELTA Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582).
MAINTENANCE
KEEP MACHINE CLEAN
LUBRICATION
Periodically blow out all air passages with dry compressed
air. All plastic parts should be cleaned with a soft damp
cloth. NEVER use solvents to clean plastic parts. They could
possibly dissolve or otherwise damage the material.
Apply household floor paste wax to the machine table and
extension table or other work surface weekly.
PROTECTING CAST IRON FROM RUST
To clean and protect cast iron tables from rust, you will
need the following materials: 1 pushblock from a jointer,
1 sheet of medium Scotch-Brite™ Blending Hand Pad, 1
can of WD-40®, 1 can of degreaser, 1 can of TopCote®
Aerosol. Apply the WD-40 and polish the table surface
with the Scotch-Brite pad using the pushblock as a
holddown. Degrease the table, then apply the TopCote®
accordingly.
Wear ANSI Z87.1 safety glasses while
using compressed air.
FAILURE TO START
Should your machine fail to start, check to make sure the
prongs on the cord plug are making good contact in the
outlet. Also, check for blown fuses or open circuit breakers
in the line.
SERVICE
PARTS, SERVICE OR WARRANTY ASSISTANCE
All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network
of Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional
information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location
of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582).
24
ACCESSORIES
A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers,
and Delta Authorized Service Stations. Please visit our Web Site www.deltamachinery.com for a catalog or
for the name of your nearest supplier.
Since accessories other than those offered by Delta have not been tested
with this product, use of such accessories could be hazardous. For safest operation, only
Delta recommended accessories should be used with this product.
WARRANTY
Two Year Limited New Product Warranty
Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory
which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product
prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two
years and provides Delta with reasonable opportunity to verify the alleged defect by inspection. For all refurbished Delta
product, the warranty period is 180 days. Delta may require that electric motors be returned prepaid to a motor
manufacturer’s authorized station for inspection and repair or replacement. Delta will not be responsible for any asserted
defect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by
anyone other than an authorized Delta service facility or representative. Under no circumstances will Delta be liable for
incidental or consequential damages resulting from defective products. This warranty is Delta’s sole warranty and sets
forth the customer’s exclusive remedy, with respect to defective products; all other warranties, express or implied, whether
of merchantability, fitness for purpose, or otherwise, are expressly disclaimed by Delta.
25
NOTES
26
NOTES
27
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)
Parts and Repair Service for Porter-Cable • Delta Machinery are Available at These Locations
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable • Delta)
ARIZONA
Phoenix 85013-2906
4501 N. 7th Ave.
Phone: (602) 279-6414
Fax: (602) 279-5470
CALIFORNIA
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
San Diego 92111
7290 Clairemont Mesa Blvd.
Phone: (858) 279-2011
Fax: (858) 279-0362
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
COLORADO
Denver 80223
700 West Mississippi Ave.
Phone: (303) 922-8325
Fax: (303) 922-0245
FLORIDA
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: (954) 321-6635
Fax: (954) 321-6638
Tampa 33634
4909 West Waters Ave.
Phone: (813) 884-0434
Fax: (813) 888-5997
GEORGIA
Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Phone: (404) 608-0006
Fax: (404) 608-1123
ILLINOIS
Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: (630) 424-8805
Fax: (630) 424-8895
KANSAS
Overland Park 66214
9201 Quivira Road
Phone: (913) 495-4330
Fax: (913) 495-4378
MARYLAND
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
MASSACHUSETTS
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
MICHIGAN
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
Fax: (248) 597-5004
MINNESOTA
Eden Prairie 55344
9709 Valley View Road
Phone: (952) 884-9191
Fax: (952) 884-3750
OREGON
Portland 97230
14811 North East Airport Way
Phone: (503) 255-6556
Fax: (503) 255-6543
MISSOURI
St. Louis 63146
11477 Page Service Drive
Phone: (314) 997-9100
Fax: (314) 997-9183
PENNSYLVANIA
Willow Grove 19090
(Philadelphia)
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
NEW YORK
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
NORTH CAROLINA
Charlotte 28270
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625
OHIO
Columbus 43229
1948 Schrock Road
Phone: (614) 895-3112
Fax: (614) 895-3187
Parma Heights OH 44130
6485 Pearl Road
Phone: (440) 842-9100
Fax: (440) 884-3430
TEXAS
Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
Houston 77022-2122
536 East Tidwell Rd.
Phone: (713) 692-7111
Fax: (713) 692-1107
WASHINGTON
Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: (253) 333-8353
Fax: (253) 333-9613
Authorized Service Stations are located in many large cities. Telephone 800-438-2486 or 731-541-6042 for assistance locating one.
Parts and accessories for Porter-Cable·Delta products should be obtained by contacting any Porter-Cable·Delta Distributor, Authorized
Service Center, or Porter-Cable·Delta Factory Service Center. If you do not have access to any of these, call 800-223-7278 and you will
be directed to the nearest Porter-Cable·Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas
grandes ciudades. Llame al 800-438-2486 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios
para los productos Porter-Cable·Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable·Delta, Centro
de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable·Delta. Si no tiene acceso a ninguna de estas opciones, llame al
800-223-7278 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable·Delta más cercano.
CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS
ALBERTA
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
Phone: (403) 735-6166
Fax: (403) 735-6144
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: (604) 420-0102
Fax: (604) 420-3522
MANITOBA
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
Phone: (204) 633-9259
Fax: (204) 632-1976
ONTARIO
505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: (519) 767-4132
Fax: (519) 767-4131
QUÉBEC
1515 ave.
St-Jean Baptiste, Suite 160
Québec, Québec
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
1447, Begin
St-Laurent, (Montréal),
Québec
H4R 1V8
Phone: (514) 336-8772
Fax: (514) 336-3505
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques
suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®, Contractor’s Saw®,
Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying Chips™, FRAME SAW®,
Grip Vac™, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-SET®, Micro-Set®, MIDI LATHE®,
MORTEN™, NETWORK™, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-CABLE®&(design), PORTERCABLE®PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic®, Q-3®&(design), QUICKSAND®&(design),
QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®, Sanding Center®, SANDTRAP®&(design), SAW
BOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®, The American Woodshop®&(design), The Lumber
Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-LINE™, TIGER®, TIGER CUB®, TIGER SAW®,
TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®, UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®,
Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®, WOODWORKER’S CHOICE™.
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries. Las
Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden estar
registradas en otros países.
PC7.2-0105-149