Biljax 5533 Operators Manual - Cobb Rental Service, Supplying

Transcription

OPERATOR’S
MANUAL
BOOM PERSONNEL LIFT
This equipment is designed and manufactured in
compliance with the duties, responsibilities and
standards set forth in the ANSI, CE CSA and/or AS
standards in effect at the time of manufacture.
This equipment will meet or exceed applicable ANSI,
CE, CSA and/or AS codes and standards when
operated in accordance with manufacturer’s
recommendations.
It is the responsibility of the user to follow all regional
codes and regulations that govern the safe operation of
this equipment.
Obtain, read and obey all safety precautions before
performing maintenance or repairs or attempting to
operate this equipment. This includes all manufacturer
recommendations as well as those directives set forth by
government and local authorities.
To ensure proper and safe use of this equipment, it is
strongly recommended that only trained and authorized
personnel attempt to operate and maintain the boom lift.
This manual shall be considered a permanent and
necessary component of the machine and shall be kept
with the boom lift at all times.
Owners and Lessors should complete a full inspection of
all components and perform a test of all functions,
including brake functions, before commissioning or
reselling the machine. Repair or replace all damaged or
malfunctioning components.
Bil-Jax, Inc. is dedicated to the continuous improvement
of this and all Bil-Jax products. Therefore, equipment
information is subject to change without notice. Direct
any questions or concerns regarding errors or
discrepancies in this manual to the Bil-Jax Service
Department.
Copyright © Bil-Jax, Inc. 2007. All Rights Reserved.
“Bil-Jax” is a registered trademark and “A Step Above”
and “Summit Series” are trademarks of Bil-Jax, Inc.
Contact Bil-Jax for replacement manuals.
125 Taylor Parkway
Archbold, Ohio 43502
Phone (800) 537-0540
(419) 445-8915
Fax (419) 445-0367
P/N B33-01-0097
http://www.biljax.com
TABLE OF CONTENTS
Table of Contents
1
Illustrations
2
Tables
2
1 Safety
3
Legend: Safety Advisories
Before Operation
During Operation
Maintenance Safety
Damaged Equipment Policy
4
5
5
7
8
2 Specifications
9
Range of Motion
Specifications
Warranty
10
11
12
3 Operations
Ground Control Station
Platform Control Station
Normal Operating Procedure
Manual Boom Operations
Battery Recharge
Boom Lift Transport
4 Operator Service
13
14
16
18
20
22
23
25
Daily Service Checks
Weekly Service Checks
Monthly Service Checks
Troubleshooting
Error Code Definitions
26
28
29
30
31
5 Replacement Decals
35
6 ANSI Reprint
39
7 Material Safety Data
45
8 Equipment Options
49
Material Lifting Hook
Platform Rotator
Drive and Set
Replacement Decals
50
51
52
55
Service Checklists
56
1
LIST OF ILLUSTRATIONS
Figure 2-1
Range of Motion
10
Figure 3-1
Ground Control Panel
14
Figure 3-2
Platform Control Panel
16
Figure 3-3
Outrigger Controls
18
Figure 3-4
Boom Travel Latch
18
Figure 3-5
Hand Pump and Controls for Manual Operation
20
Figure 3-6
Manual Lowering Valve
21
Figure 3-7
Battery Charger Faceplate
22
Figure 3-8
Trailer Hitching
23
Figure 3-9
Boom Lift and Transport Instructions
24
Figure 4-1
Outrigger Position Switches
26
Figure 4-2
Hydraulic Reservoir
27
Figure 4-3
Wheel Nut Tightening Sequence
29
Figure 5-1
Decal Placements
37
Figure 6-1
Minimum Safe Approach Distances
43
Figure 8-1
Material Lifting Hook Configuration
50
Figure 8-2
Material Lifting Hook Installation
50
Figure 8-3
Manual Platform Rotator
51
Figure 8-4
Jockey Wheel Instruction
52
Figure 8-5
Drive and Set Controls
53
Figure 8-6
Material Lift Decal Placement
55
Figure 8-7
Optional Components Decal Placement
55
LIST OF TABLES
2
Table 1-1
4
Table 3-1
Charger Fault Codes
22
Table 4-1
Troubleshooting Steps
30
Table 4-2
Error Code Definitions
31
Table 5-1
Replacement Decal Descriptions
36
Table 8-1
Replacement Decals – Optional Components
55
1 SAFETY
Proper training is required for the safe operation of any mechanical device.
Failure to follow all instructions and safety precautions in this manual and
attached to the lift will result in death or personal injury.
Prior to Operation:
Read, understand and obey all instructions and safety precautions in this
manual and attached to the lift.
Read, understand and obey all applicable government regulations.
Become familiar with the proper use of all controls.
Inexperienced users should receive instruction before attempting to
operate or maintain the machine.
The use of intelligence and common sense is the best practice when
following any safety policy.
3
BIL-JAX 5533A
LEGEND: SAFETY ADVISORIES
The following safety advisories are used throughout
this manual to indicate specific hazards when
operating or maintaining the machine. Read,
understand and obey all safety advisories to prevent
improper service, damage to equipment, personal
injury or death.
DANGER
Warns of operation near electrical power
sources that could lead to personal injury or
death.
WARNING
Describes conditions or practices that could lead
to personal injury or death.
CAUTION
Contains information important in the prevention
of errors that could damage machine or
components.
NOTE: Contains additional information
important for performing a procedure.
4
1 – SAFETY
BEFORE OPERATION
DURING OPERATION
Ensure the following general safety precautions are
followed before operating the telescoping boom lift:
followed while operating the telescoping boom lift:
ALWAYS inspect the usage area for potential
hazards, such as unstable or unlevel surfaces,
overhead obstructions and electrically charged wires
or conductors. ALWAYS watch for moving vehicles
in the operating area.
ALWAYS position lift away from power lines to
ensure that no part of the lift can accidentally reach
into an unsafe area. This includes full extension of
the boom through 700º rotation.
ALWAYS conduct a thorough inspection of the
machine before operation. Check for damaged or
worn parts, hydraulic leaks, damaged wiring, loose
wiring conductors, damaged outriggers, low tire
pressure, uneven tire wear or tire damage. Check for
any improperly operating components. NEVER
operate equipment if any damage is observed or
suspected. Repair damaged or malfunctioning
equipment before operation.
ALWAYS wear proper clothing. Wear protective
equipment as required by government regulations.
Keep loose clothing, jewelry, gloves and hair away
from moving parts.
ALWAYS wear a safety harness and energyabsorbing lanyard, such as the safety harness and
lanyard provided by Bil-Jax.
DANGER
This machine is NOT insulated for use near
electrical power lines and DOES NOT provide
protection from contact with or close proximity
to any electrically charged conductor. Operator
must maintain safe clearances at all times (3.05
meters minimum) and must always allow for
platform movement due to gusty winds. Always
contact power company before working near
power lines. Assume every power line is live.
Power lines can be blown by the wind. Refer to
Table 1-1 for minimum safe approach distances
between the machine and electrical power lines.
Voltage Range
(Phase to Phase)
ALWAYS inspect platform floor and outrigger
footpads for mud, grease, debris or other foreign
material. ALWAYS remove any such material from
the equipment before operation.
0 to 300V
Over 300V to 50KV
Minimum Safe Approach Distance
(Feet)
(Meters)
Avoid Contact
10
3.05
Over 50KV to 200KV
15
4.60
Over 200KV to 350KV
20
6.10
ALWAYS tag any part of the equipment known or
suspected to be damaged or malfunctioning.
ALWAYS remove a malfunctioning, damaged or
defective machine from service. NEVER operate a
machine that has any known or suspected defect.
Over 350KV to 500KV
25
7.62
Over 500KV to 750KV
35
10.67
Over 750KV to 1000KV
45
13.72
ALWAYS comply with the instructions found in
Safety and/or Service Bulletins distributed by the
manufacturer. Bulletins may contain critical
procedures that supersede the information
contained in manuals.
ALWAYS keep away from a machine that is
exposed to energized power lines. If the machine
contacts energized power lines, NEVER touch or
operate the machine until power lines are shut off.
NEVER operate this equipment while under the
influence of drugs or alcohol, while taking
prescription medications that may leave the operator
drowsy or prone to dizziness, or while feeling ill.
NEVER modify, alter or change the equipment in
any way that would affect its original design or
operation.
NEVER deface, modify or obscure any decals or
markings on equipment.
NEVER operate the equipment in any way for which
it is not intended.
Table 1-1. Minimum Safe Approach Distances
ALWAYS operate only on a firm and level surface.
NEVER operate on surfaces that do not support the
equipment with its rated load capacity or on surfaces
that do not support force exerted by the outriggers
during boom operation. Operate only on surfaces
that can support a pressure of 1.8 kg/cm2 (25 psi) to
ensure safe operation.
ALWAYS keep personnel away from potential pinch
and shear points and from potential crush hazards
as indicated by decals attached to the machine.
ALWAYS maintain sure footing on the work platform.
ALWAYS keep the safety bar lowered unless
personnel are entering or exiting the work platform.
5
BIL-JAX 5533A
ALWAYS wear proper footgear. ALWAYS keep the
platform free of debris.
ALWAYS keep personnel and obstructions clear of
the machine when repositioning boom or basket.
ALWAYS cordon the area surrounding the
outriggers to keep personnel, vehicles and moving
equipment away from the machine while in use.
ALWAYS stay clear of overhead obstructions,
including wires and cables.
ALWAYS engage boom travel latches before towing
trailer.
ALWAYS exercise caution when rotating the boom
(slew) from the ground control station. ALWAYS
watch for personnel inside the radius of the turntable
and boom arm when rotating the boom lift from the
ground or platform controls.
ALWAYS remove personnel from the boom lift
before attempting to free an elevated platform that
has become caught or snagged on an adjacent
structure or obstacle.
NEVER operate the machine on any surface other
than firm and level ground. NEVER operate the
machine from a position on truckbeds, trailers,
floating vessels or scaffolding without written
approval from the manufacturer.
NEVER operate lift on slopes exceeding 12.5º.
NEVER allow electrode contact with any part of the
machine while welding from the platform. NEVER
use the machine as a ground for welding.
NEVER operate without the outriggers fully
extended or when the machine is not level.
NEVER position an elevated platform against
another object to steady the platform
NEVER override or bypass the manufacturer’s
safety devices.
NEVER attach a safety harness to an adjacent
structure, pole, or to nearby equipment while
working from the boom platform.
NEVER raise the outriggers or move the trailer with
materials or personnel on board, or while boom is
raised or extended.
NEVER sit, stand or climb on cage bars. ALWAYS
keep both feet firmly on the work cage floor when
working from an elevated platform.
NEVER attempt to increase the working height with
boxes, ladders, stools or any other materials.
NEVER operate this equipment when exposed to
high winds, thunderstorms, ice or any weather
conditions that would compromise operator safety.
6
NEVER operate boom lift in conditions where wind
speeds exceed 12.5 m/sec (45 km/h or 28 mph).
Steady or gusty winds that exceed 12.5 m/sec (45
km/h) may affect stability and boom operation.
NEVER allow ropes, electric cords, hoses or other
equipment to become entangled in the machine
while raising or lowering platform.
NEVER exceed the load limits set by the
manufacturer. Use only the Material Lifting Hook,
supplied as an option and manufactured by Bil-Jax,
when lifting materials. Safely stow all tools and
equipment.
NEVER exceed load ratings by transferring loads to
the lift at elevated heights.
NEVER use the platform to lift a load that exceeds
the platform dimensions. NEVER lift a load in such a
way that the center of gravity is higher than the top
guardrail of the platform.
NEVER modify the platform or carry materials that
would increase the surface area of the platform.
Increasing the area exposed to the wind may
decrease machine stability. NEVER attach
overhanging loads when raising or lowering the
platform.
NEVER use the boom or platform to push or pull or
to lift any part of the trailer.
NEVER use the boom or platform to place a load
against any structure, materials or equipment.
NEVER climb on the boom. Refer to Section 3 for
the instructions for manual operation.
NEVER leave an elevated platform unattended.
NEVER leave the keys in the boom lift while
unattended or not in use.
1 – SAFETY
MAINTENANCE SAFETY
followed while performing maintenance on the
telescoping boom lift:
General Maintenance
ALWAYS perform maintenance procedures
according to manufacturer’s guidelines. NEVER
disregard or bypass proper maintenance
procedures.
ALWAYS inspect hydraulic system to ensure that all
lines, connectors and fittings are properly fastened
and in good condition.
ALWAYS turn the key switch OFF and remove key
before performing maintenance.
Whenever possible, ALWAYS perform maintenance
with the boom and platform in a fully lowered,
stowed position. ALWAYS secure the boom before
performing maintenance on hydraulic cylinders.
ALWAYS disconnect power to the hydraulic pump
drive motor before making electrical checks to the
hydraulic valves.
ALWAYS keep all mechanical parts properly
adjusted and lubricated according to maintenance
schedule and manufacturer’s specifications.
ALWAYS perform a function check of operating
controls before each use and after repairs have
been made.
ALWAYS locate and protect against possible pinch
points before performing any maintenance or
repairs.
ALWAYS use only manufacturer-approved parts to
repair or maintain equipment. If any portion of this
equipment is rebuilt or repaired, retesting is required
in accordance with factory instructions.
ALWAYS maintain a safe distance while testing the
hydraulic components. ALWAYS relieve hydraulic
pressure before loosening or removing hydraulic
components. NEVER test or operate the hydraulic
components while personnel are near the
equipment.
NEVER exceed the manufacturer’s recommended
relief valve settings.
NEVER touch or allow metal tools to contact any
components that are sensitive to static discharge.
ALWAYS use static discharge prevention mats and
grounding devices when handling electronic
components.
NEVER adjust, repair, replace or bypass any
hydraulic or electrical control or safety device. These
include, but are not limited to, hydraulic load control
and flow control valves, solenoid valves and limit
switches. ALWAYS consult an authorized Bil-Jax
technician if repairs are necessary.
NEVER modify, alter or change the equipment
without first consulting an authorized Bil-Jax
technician, and NEVER in any way that would affect
its original design or operation.
Battery Maintenance
followed when performing battery maintenance on
the telescoping boom lift.
ALWAYS check the battery fluid level daily.
ALWAYS wear safety glasses when working with or
near batteries.
ALWAYS avoid contact with battery acid. Battery
acid causes serious burns and should be kept away
from skin or eyes. If contact occurs, flush with water
and consult a physician immediately.
ALWAYS disconnect ground cable first when
removing battery.
ALWAYS connect ground cable last when installing
battery.
ALWAYS charge batteries in open, well-ventilated
areas.
ALWAYS replace batteries using only parts
recommended by manufacturer. ALWAYS use only
batteries with sealed caps over cells.
NEVER smoke while servicing batteries.
NEVER allow water or foreign particles into the DC
electric motor housing. Inclusion of water or foreign
particles may cause serious damage to the motor. If
the motor becomes wet, consult an authorized BilJax service technician for proper drying instructions.
NEVER charge batteries near flammable materials.
NEVER add unauthorized fluids to the hydraulic
system or battery. NEVER mix hydraulic oils.
Consult manufacturer specifications. Refer to
Section 4 for hydraulic system maintenance
procedures.
NEVER disconnect battery from charger while
charger is connected to a live power source.
NEVER allow batteries to overcharge and boil.
NEVER short across battery posts to check for
current. NEVER break a live circuit at the battery.
NEVER jumpstart other vehicles using the boom lift
batteries.
7
BIL-JAX 5533A
DAMAGED EQUIPMENT POLICY
Safety Statement
At Bil-Jax, we are dedicated to the safety of all users of our products. All Bil-Jax
lifts are designed, manufactured and tested to comply with current applicable
ANSI and/or CE codes and regulations.
Damage Policy
There may be occasions when a Bil-Jax lift is involved in an incident that results
in structural damage to the lift. Such damage can seriously compromise the
ability of the lift to perform in a safe manner. Therefore, whenever a Bil-Jax lift is
damaged structurally or when there is suspected internal damage to the
structure, Bil-Jax may require that the lift be returned to our facility for
reconditioning. For any questions concerning structural damage or the Damaged
Equipment Policy, please contact an authorized Bil-Jax representative or your
regional Bil-Jax dealer
Damage Repair Notice
There may be occasions when a Bil-Jax lift is involved in an accident resulting in
damage to non-structural components. When such damage occurs and repairs
are made by the owner or area distributor, please notify Bil-Jax of these nonmaintenance repairs and request a repair form to be filled out and returned to BilJax.
8
2 SPECIFICATIONS
Bil-Jax, Inc. is dedicated to the continuous improvement of this and all
Bil-Jax products. Therefore, equipment information is subject to change
without notice.
The following information is based on ideal working conditions. Machine
performance may vary based on work environment and on machine
options.
Direct any questions or concerns regarding equipment specifications to
your regional Bil-Jax representative or to the Bil-Jax Service Department.
9
BIL-JAX 5533A
RANGE OF MOTION
Figure 2-1. Range of Motion
10
2 – INTRODUCTION
SPECIFICATIONS
SERIAL NUMBER_____________________________
Working Height
61 ft 3 in
18.8 m
Maximum Platform Height
55 ft 3 in
16.8 m
Maximum Horizontal Outreach
From Centerline
From Outrigger Footpad Edge
Rated Platform Capacity
Without Platform Rotation
With Platform Rotation
Maximum Occupants
Tongue Weight
Total Weight
500 lbs
227 kg
440 lbs
200 kg
2
270 lbs
122 kg
4,400 lbs
1,996 kg
700º Non-Continuous
Leveling Capability
12.5º
Length
Width
Stowed Dimensions
Height
Length
Width
Outrigger Footprint
Length
Width
Footpad Diameter
Parking Brake
Rated Towing Speed
Tire Size
Control System
33 ft 5 in
10.2 m
27 ft 4 in
8.2 m
Turntable Rotation
Platform Dimensions
Height
Towing Brake
3 ft 7 in
1.1 m
2 ft 6 in
0.8 m
4 ft
1.2 m
6 ft 6 in
2.0 m
22 ft 11 in
7.0 m
5 ft 7 in
1.7 m
12 ft 11 in
3.9 m
12 ft 9 in
3.9 m
12.5 in
0.3 m
Standard, Mechanical
Battery
Charger
Standard
CE
Mechanical Surge
65 mph
105 km/h
ST 225/75 R15D
24V DC
4 x 6V 245 amp-hr
110/120 Volt
220 Volt
Hydraulic Pressure
3,000 psi
20,684 kPa
Reservoir Capacity
5.6 Gallons
21.2 L
Hydraulic System Capacity
8.5 Gallons
32.2 L
Hydraulic Oil (Standard)
Dexron III/Mercon ATF
Platform Rotation/Type (Optional)
90º/Manual
Maximum Decibel Level
Standard DC Mode – Ground
Standard DC Mode – Platform
DC/Gas Option – Ground
DC/Gas Option - Platform
60 dB
55 dB
70 dB
65 dB
Function Speeds
Boom Raise (Fast)
30-35 Seconds
Boom Raise (Slow)
50-55 Seconds
Boom Lower (Fast)
45-50 Seconds
Boom Lower (Slow)
120-150 Seconds
Boom Extend (Fast)
30-35 Seconds
Boom Extend (Slow)
75-90 Seconds
Boom Retract (Fast)
40-45 Seconds
Boom Retract (Slow)
100-110 Seconds
Turntable Rotation (Fast)
82-90 Seconds
Turntable Rotation (Slow)
240-270 Seconds
Platform Level (Fast)
8-10 Seconds
Platform Level (Slow)
12-16 Seconds
Outrigger Extend
15-20 Seconds
Outrigger Retract
25-30 Seconds
Localized Pressure per Outrigger
Operation Temperature Range
25 psi
2
1.8 kg/cm
176.5 kPa
-20º to 110º Fahrenheit
-29º to 43º Celsius
11
BIL-JAX 5533A
WARRANTY
Bil-Jax, Inc. warrants this product for one year, beginning on the date of delivery,
to be free from defects of material and workmanship provided the unit is operated
and maintained in compliance with the guidelines established in the Operations
and Maintenance Manuals. Major structural components, including trailer tongue
and boom weldments, are warranted for five years against defects due to
material or workmanship. Bil-Jax will, at its option, repair or replace any unit or
component part that fails to function properly during normal use.
The warranty does not apply if the lift and/or its components have been altered,
changed, or repaired without the consent of Bil-Jax. Repairs, damage, or defects
resulting from the following are not covered under the terms of the warranty:
negligence, misuse, accidental damage, inadequate or improper maintenance,
acts of nature, damage caused by chemicals or abrasive materials, and normal
wear and tear, such as rust or corrosion. Components not covered under this
warranty include tires, filters, covers, and routine maintenance items.
Components not manufactured by Bil-Jax are covered by their respective
manufacturer’s warranties. A list of those components and their warranties is
available upon written request to Bil-Jax.
Bil-Jax shall not in any event be liable for the cost of any special, indirect, or
consequential damages to any person, product, or thing. Bil-Jax’s maximum
liability under this warranty is limited to the amount paid to Bil-Jax for the product.
This warranty is in lieu of all other warranties expressed or implied. Bil-Jax
neither assumes nor authorizes any or other entity to assume on its behalf any
other liability in connection with the sale, rental, or use of this product.
Warranty Claims Process
In order to qualify for warranty coverage, the following conditions must be met:
1.
Return of completed “Warranty Registration” form to Bil-Jax within 15 days of receipt
of product;
2.
Notification to Bil-Jax within 72 hours of any claimed defect, injury, or damage
resulting from the claimed defect; and
3.
Warranty is limited to parts that are determined to be defective. This does not include
parts worn out due to normal use.
4. Bil-Jax authorized dealers or distributors are responsible for filing claims
under warranty. Listed below is the warranty claims procedure.
5.
Contact Bil-Jax Service Department at 800-537-0540 to report the claim and verify
warranty coverage. Machine serial number must be provided.
6.
Identify the components to be claimed under warranty along with description of
failure. A Returned Merchandise Authorization (RMA) number will be issued by BilJax.
7.
Replacement parts will then be sent by Bil-Jax to the dealer or distributor. All parts
are invoiced at dealer/distributor list price. Credits will be issued when defective parts
are returned to Bil-Jax and found to be defective under warranty.
8.
After completing repairs, submit warranty claim form and defective parts to Bil-Jax.
Warranty claim form and parts must be received within 30 days of claim in order to be
eligible for credit. RMA number must be referenced on warranty claim form. Returned
parts are to be sent prepaid and will be credited when part is received and verified.
Warranty labor rate will be paid at current rate set by Bil-Jax. The amount of labor
hours reimbursed will be determined by Bil-Jax and will be limited to 4 hours unless
approved by Bil-Jax.
Failure to follow the warranty claims process may result in delay in processing
claim or denial of the claim. Bil-Jax reserves the right to limit or adjust warranty
claims with regard to parts, labor and travel time. Components purchased from
suppliers other than Bil-Jax are not covered under the terms of this warranty.
12
3
OPERATION
The Bil-Jax Telescoping Boom Lift is equipped with multiple operator
control stations. Equipment power and outrigger controls are located at
ground level. Boom lift and rotation controls are located at ground level
and on the work platform.
Before attempting boom lift operation, Operators should:
Attend a training program as required by government regulations.
Obtain, read and obey all safety precautions as indicated by
manufacturer’s recommendations and all federal, state and local
regulations.
Become familiar with the location and use of all controls.
Verify that there are no overhead obstructions or live power sources
in the work area that could interfere with the safe operation of the
boom lift.
Position the boom lift on a firm and level surface.
Conduct a Pre-Operation inspection by performing all recommended
Daily Service Checks. Refer to Section 4.
Unhitch equipment trailer from the tow vehicle.
13
BIL-JAX 5533A
GROUND CONTROL STATION
The ground control station is used to operate outriggers and control
boom motion. To access the ground control station, open the control
panel access cover found on the turntable. Turn the key switch to the
ground controls setting.
Figure 3-1. Ground Control Panel
14
1. Key Switch
12. Upper Boom Down
1a. Ground Controls Position
13. Jib Raise
1b. Platform Controls Position
14. Jib Down
2. Battery Condition Indicator
15. Speed Buttons
3. Engine Start
16. Platform Tilt – Up
4. Engine Choke
17. Platform Tilt – Down
5. Display Panel
18. Boom Rotation – Clockwise
6. Emergency Stop
19. Boom Rotation – Counterclockwise
7. Boom Extend
20. Outrigger Status Indicator LED
8. Boom Retract
21. Outrigger Extend
9. Lower Boom Raise
22. Outrigger Retract
10. Lower Boom Down
23. Auto Level
11. Upper Boom Raise
24. Outrigger Button
3 – OPERATION
The ground control station includes the following
controls and Indicators. Refer to Figure 3-1 for
control locations.
1. Key Switch
Turning the key switch to the PLATFORM (1A) icon
selects operation from the platform. Turning the key
switch to the GROUND (1B) icon selects operation
from the ground control panel. The center (power
off) position interrupts all electric and hydraulic
power operations except emergency lowering.
Removing the key protects against operation by
unauthorized persons. The key may be removed
with the key switch in any selected position.
Indicator LEDs light up to indicate the level of charge
remaining in the batteries. A lighted green LED
indicates an adequate charge level. Lighted yellow
LEDs indicate the need for charging soon. A lighted
red LED warns that the battery charge level is low;
boom operations should be halted until the batteries
are recharged.
3-4. Engine Start and Choke
Start a cold engine by pressing the Engine START
button while pressing and holding the CHOKE button.
To start/restart a warm engine, press the START
button only.
5. Display Panel
The DISPLAY PANEL is a lighted text window that
displays the present operating status or an existing
error condition when the key switch is on.
6. Emergency Stop Button
When pushed in, the emergency STOP button
disconnects electrical power to the ground and
platform control stations. The emergency STOP
pushbutton should only be pressed to immediately
stop all boom motion. To resume control, pull out the
emergency STOP button.
7-8. Boom Extend/Retract Buttons
Pressing and holding a desired SPEED button and the
at the same time extends the
telescopic boom. Pressing and holding a desired
SPEED button and the BOOM RETRACT button at the
same time retracts the boom. Boom motion
continues until the buttons are released or until the
boom reaches a hard stop or a safe travel limit.
BOOM EXTEND button
9-14. Boom Raise/Down Buttons
button at the same
time will raise the chosen boom. Pressing a desired
SPEED button and the UPPER/LOWER/JIB BOOM DOWN
button at the same time will lower the chosen boom.
Boom motion continues until the buttons are
released or until the boom reaches a hard stop or a
safe travel limit.
UPPER/LOWER/JIB BOOM RAISE
15. Speed Buttons
The SPEED buttons along the lower right side of the
control panel must be pressed and held while
selecting a boom function. Four speeds are
available to control the positioning of the boom lift.
16-17. Platform Tilt Buttons
Press and hold any SPEED button and the desired
button at the same time to level the
work platform (levels the platform only, not the boom
lift).
PLATFORM TILT
18-19. Boom Rotation Buttons
BOOM ROTATION CLOCKWISE or COUNTERCLOCKWISE
button at the same time enables the boom to rotate
in the direction selected. The boom will rotate
through 700 degrees until the buttons are released
or the stop is reached.
20-24. Outrigger Controls
For automatic outrigger extension/retraction: Select
EXTEND or RETRACT outrigger button and the AUTO
LEVEL button at the same time. To manually extend
or retract the outriggers: Select EXTEND or RETRACT
outrigger button and one of the OUTRIGGER buttons
at the same time. The outrigger indicator LEDs light
up when the outriggers are properly deployed and
the boom weight is on the outriggers. Each of the
outer outrigger LEDs indicates load is on the
outrigger footpad. Each of the inner outrigger LEDs,
when flashing, indicate that side is low and needs to
be further raised for leveling. The Auto Level LED
lights up and a buzzer sounds when the boom is
level.
15
BIL-JAX 5533A
PLATFORM CONTROL STATION
The platform control station is used to control boom motion. To access the
platform control station, turn the key switch at the ground control station to the
platform controls setting and enter the work cage.
Figure 3-2. Ground Control Panel
16
1. Engine Start (DC/Gas Model Only)
10. Lower Boom Down
2. Engine Choke (DC/Gas Model Only)
11. Upper Boom Raise
3. Horn Button
12. Upper Boom Down
13. Jib Boom Raise
14. Jib Boom Down
6. Speed Buttons
15. Boom Extend
7. Boom Rotation – Clockwise
16. Boom Retract
8. Boom Rotation – Counterclockwise
17. Platform Tilt – Up
9. Lower Boom Raise
18. Platform Tilt – Down
3 – OPERATION
The platform control station includes the following
controls and Indicators. Refer to Figure 3-2 for
control locations.
1-2. Engine Start and Choke (DC/Gas Model only)
Start a cold engine by pressing the CHOKE button,
then press the engine START button to start the
engine. To start/restart a warm engine, press the
START button only.
3. Horn Button
Pressing the button will sound the horn. Use the
HORN button to warn personnel in the area of a
falling object hazard, impending boom motions, or
the need for assistance.
Indicator LEDs light up to indicate the level of charge
remaining in the batteries. A lighted green LED
indicates a good charge level. Lighted yellow LEDs
indicate the need for charging soon. A lighted red
LED warns that the battery charge level is low; boom
operations should be halted until the batteries are
recharged.
15-16. Boom Extend/Retract Buttons
BOOM EXTEND button at the same time extends the
telescopic boom. Pressing and holding a desired
SPEED button and the BOOM RETRACT button at the
same time retracts the boom. Boom motion
continues until the buttons are released or until the
boom reaches a hard stop or a safe travel limit.
17-18. Platform Tilt Buttons
Press and hold any SPEED button and the desired
button at the same time to level the
work platform (levels the platform only, not the boom
lift).
PLATFORM TILT
Outlet
The outlet is provided for running electrical power
tools from the work platform. A connecting power
cord must be plugged into a suitable power source.
The power plug is located on the trailer frame, in
front of the accessory equipment stowage plate. The
outlet is rated for a 15-ampere load. Do not overload
the accessory power circuit.
When pushed in, the emergency STOP button
disconnects electrical power to the ground and
platform control stations. The emergency STOP
pushbutton should only be pressed to immediately
stop all boom motion. To resume control, pull out the
emergency STOP button.
6. Speed Buttons
The SPEED buttons along the lower right side of the
control panel must be pressed and held while
selecting boom functions. Four speeds are available
to control the positioning of the boom lift.
7-8. Boom Rotation Buttons
BOOM ROTATION CLOCKWISE or COUNTERCLOCK-WISE
button at the same time enables the boom to rotate
in the direction selected. The boom will rotate
through 700 degrees until the buttons are released
or the stop is reached.
9-14. Boom Raise/Down Buttons
UPPER, LOWER or JIB BOOM RAISE button at the same
time will raise the boom. Pressing a desired SPEED
button and the UPPER, LOWER or JIB BOOM DOWN
button at the same time will lower the boom. Boom
motion continues until the buttons are released or
until each boom reaches a hard stop or a safe travel
limit.
17
BIL-JAX 5533A
NORMAL OPERATING PROCEDURE
Perform the following procedures to operate the BilJax Telescoping Boom Lift.
and the two appropriate OUTRIGGER buttons at
the same time.
Read and obey all safety precautions and
operating instructions, as well as all applicable
government regulations.
Conduct a Pre-Operation Inspection by
performing all recommended Daily Service
Checks. Refer to Section 4.
Position the boom lift at the work area. Make
sure the boom lift is on a firm and level surface
and there are no potential hazards such as
overhead obstructions or electrically charged
conductors. Do not operate the boom lift if such
hazards exist.
Apply the boom lift parking brake or chock the
wheels.
Lower the tongue jack and unhitch the boom lift
from the tow vehicle.
WARNING
Failing to unhitch the boom lift before operation
may lead to damage to equipment or tow vehicle
and makes the boom lift unstable, which can
cause personnel injury or death.
Turn the key switch on the ground control station
to operate ground controls. If power does not
come on, make sure both emergency STOP
buttons (ground and platform) are pulled out and
the main power disconnect is plugged in.
The control microprocessor will perform selfdiagnostics to test the operating system. After
several seconds, the DISPLAY PANEL window
will read:
BIL – JAX
A STEP ABOVE
Verify that the control status indicator LED is lit.
If the control status indicator LED is not lit or is
flashing, the outrigger buttons will not work. A
flashing control status LED indicates that one or
more of the booms is raised and needs to be
stowed. Refer to Figure 3-1 and Figure 3-3.
Figure 3-3. Outrigger Controls
NOTE: The safety interlock system prevents all
boom operations if the boom is not level
or if one or more outriggers are not
supporting the vehicle load.
NOTE: The Range of Motion Diagrams at the
ground and platform control stations
display the range of platform motion
(safe operating zone) facing away from
the trailer tongue. Verify that the
operating zone is clear of obstructions
through 700º of turntable rotation.
Verify that the auto level indicator LED is lit. If
the auto level indicator is not lit, the boom may
not be level.
Pull the latch release on the boom travel latches,
raise the latch handle and swing the latch U-bolt
down. Refer to figure 3-4.
Extend the outriggers manually or using the
AUTO LEVEL button. When the boom is leveled
properly, a buzzer will sound and two LEDs at
each OUTRIGGER button and the LED at the AUTO
LEVEL button will be lit.
Auto Level: Press and hold the EXTEND and
buttons at the same time.
AUTO LEVEL
Manual Level: Extend the two outriggers
closest to the trailer coupler first. Lower each
pair of outriggers by pressing the EXTEND button
18
Figure 3-4. Boom Travel Latch
3 – OPERATION
Verify that the platform is properly attached to
the mounting bracket on the boom end. The
Retaining Pin should be fully inserted through
the platform and the mounting bracket on the
boom end.
WARNING
Failure to verify proper attachment of the
platform to the boom end could cause the
platform to separate from the boom, resulting in
serious injury or death to the operator.
Press and hold the outrigger RETRACT button
and the AUTO LEVEL button until all outriggers are
fully retracted to their upright positions. Inspect
the area beneath lift and trailer for obstructions
before retracting outriggers.
Turn the key switch to the OFF position and
remove key.
Use the ground control panel to operate the
boom lift functions. Raise, lower, extend and
rotate the boom by pressing and holding the
desired SPEED and function buttons at the same
time. Become familiar with the location and
function of all controls. Learn to smoothly start
and stop all boom motions.
Fully lower the boom onto the boom rest to
position the platform for boarding. Turn the key
switch to the platform control position.
Raise the safety bar and enter the work
platform. Put on the safety harness and attach
the lanyard to the Fall Protection Attachment
Point on the side of the platform support beam.
Use the platform control panel to operate the
boom lift functions. Raise, lower, extend and
rotate the boom by pressing the desired SPEED
and function buttons at the same time. Become
familiar with the location and function of all
controls. Learn to smoothly start and stop all
boom motions.
Should the platform become tilted out of the
normal vertical axis, press and hold the desired
SPEED button and one of the PLATFORM TILT
buttons at the same time to adjust.
Monitor the Battery Condition Indicator during
operation and charge the batteries as
necessary.
Always fully retract, rotate and lower the boom
to the stowed position before exiting the
platform.
When all boom lift operations are complete, fully
retract the telescoping boom extension. Center
boom over the boom rest and fully lower boom
until seated in the stowed position for transport.
Safety switches prevent outrigger retraction until
boom is completely lowered and stowed for
transport.
Unfasten the safety harness and exit platform.
Turn the key switch to the ground controls
position.
19
BIL-JAX 5533A
MANUAL BOOM OPERATION
Manual retraction, rotation and lowering functions
allow the Telescoping Boom Lift to be moved and
lowered during hydraulic power interruption or
failure. In each instance, refer to Figure 3-5.
The following procedures for manual retraction,
rotation and lowering require a person on the ground
to operate the manual controls and hand pump.
The hydraulic hand pump is located in the pump
compartment. In case of a power failure, the hand
pump and selected hydraulic valve settings can be
used to manually retract the Telescoping boom or
rotate the boom turntable.
To begin manual retraction or rotation, turn
Proportional Valve counterclockwise until it stops,
and insert pump handle into the pump handle fitting.
Manual Retraction
Pushing and holding the Retract button while
simultaneously actuating Hand Pump will retract the
extension boom section.
Manual Rotation
To rotate the turntable clockwise: Push and hold
the Rotation button and simultaneously actuate
Hand Pump.
To rotate the turntable counterclockwise: Pull the
Rotation button out and simultaneously actuate
Hand Pump.
NOTE: Return proportional valve to its original
position before lowering the lift or
resuming normal operation.
1. Hand Pump
3. Rotation Button
2. Proportional Valve
4. Retract Button
Figure 3-5. Hand Pump and Controls for Manual Lift Operation
20
3 – OPERATION
Manual Lowering
Each Manual Lowering Valve is equipped with a
plunger, found at the base of each lift cylinder
(Figure 3-6). Use the plunger to lower the platform in
case of a complete electrical power failure, a load
shift, or other emergency. To lower the work
platform, pull the valve plunger forward. Continue
pulling the plunger to completely lower the boom.
Figure 3-6. Manual Lowering Valve
21
BIL-JAX 5533A
BATTERY RECHARGE
Recharge boom lift batteries after each 8-hour work
shift or as needed. When boom lift is not in use,
batteries should be recharged at least once per
week. Under normal circumstances, battery
recharge should take approximately 10-12 hours.
However, a full recharge may take up to 24 hours, if
the battery charge is extremely low.
The CHARGING indicator LED remains lit
continuously during the first stage of the charge
cycle. The bulk mode CHARGE CURRENT will
be displayed on the battery charger faceplate.
Press and hold the BATTERY VOLTAGE button to
display the detected battery voltage.
If a battery fault is detected, the appropriate fault
code will appear on the CHARGE CURRENT
display. The red CHECK BATTERY indicator
LED will become lit. See Table 3-1 for battery
charger fault codes.
WARNING
Recharge batteries in a well-ventilated area only.
Do no charge batteries near fire, spark or other
potential ignition sources. Batteries may emit
highly explosive hydrogen gas while charging.
Failure to properly ventilate the charge gases
may result in serious injury or death. Always
charge boom lift batteries away from flammable
materials.
To recharge the boom lift batteries:
WARNING
Do not disconnect any output leads or
connectors between the batteries and the
charger when the charger is on. To stop a charge
in progress, always unplug the extension cord
from the AC power source.
Move the boom lift to a well-ventilated area with
direct access to 120v (CE: 220v) electrical
outlet. Keep the boom lift and batteries away
from open flame or other potential ignition
sources.
When the battery charge reaches 80% of
capacity, the yellow 80% CHARGED indicator
LED will become lit and the green CHARGING
indicator LED will begin to flash.
When the batteries have reached a full charge,
the green and yellow indicator LEDs will turn
themselves off. CC (Charge Complete) will
appear on the CHARGE CURRENT display.
After two hours, this display will fade and the
CHARGE CURRENT will read 00.
Attach a 12 AWG multi-strand, grounded
extension cord with a maximum length of 15
meters to the receptacle located on the cargo
plate in front of the turntable.
NOTE: Using an underrated or long power cord
will reduce the output of the battery
charger and may extend charge time.
Unplug the extension cord from the outlet and
the charger receptacle on the boom lift. Store
the extension cord for next use.
Plug the extension cord into outlet. Verify that
the green CHARGING indicator LED is lit on the
battery charger faceplate (Figure 3-7).
Linear Battery Charger
CAUTION
Always unplug the battery charger power cord
before moving the boom lift. Failure to
disconnect power cord will cause damage to the
equipment.
CHARGING
CHARGE CURRENT
CHECK BATTERY
FUSE 15A
SLO BLO
Figure 3-7. Battery Charger Faceplate
22
Code
Description
Limits
Cause
F1
Over Voltage
>112% charge
voltage
Loose battery or
charger
connection
F2
Over Current
>60 amperes
Battery Fault
F3
Bulk Mode Timeout
14 hrs Max.
Battery Fault
F4
ARD Mode
Timeout
6 hrs Max.
Battery Fault
F5
FCT Mode Timeout
2.5 hrs Max.
Battery Fault
F6
Self-Test Error
80% CHARGED
PUSH
FOR
BATTERY VOLTAGE
Table 3-1. Charger Fault Codes
Charger Fault
3 – OPERATION
BOOM LIFT TRANSPORT
The boom lift trailer includes a single axle, two-inch
ball hitch, hydraulic surge brakes, mechanical
parking brake, safety chains, brake lights and side
marker lights. Proper boom transport requires the
proper attachment and inspection of these
components before towing. Refer to Figure 3-8.
On the tongue jack, pull the pivot locking pin and
swivel jack 90 degrees to the travel position.
Reengage pivot locking pin.
Attach the safety chains to the tow vehicle.
Verify that the chains cross under the trailer
tongue. If necessary, cross the chains first over
then under the tow bar to prevent dragging.
CAUTION
Failure to attach safety chains properly before
towing will allow trailer tongue to drop in case of
ball hitch failure, resulting in damage to trailer
and equipment.
If equipped, connect the breakaway cable to the
tow vehicle. Leave adequate slack to prevent
brakes from dragging.
Connect the trailer lights to the tow vehicle
power plug.
Verify the following before towing the lift. Make
adjustments as necessary.
1.
Trailer Hitch
2.
Trailer Parking Brake
3.
Release Lever
4.
Safety Chains
5.
Trailer-to-Vehicle Power Plug
The trailer jack and outriggers are in their travel
positions.
Boom travel latches are engaged, securing the
booms in their fully stowed positions.
All on-board equipment is secured.
Figure 3-8. Trailer Hitching
Use the following procedure to hitch and tow the
boom lift.
Back the tow vehicle to the trailer. Verify that the
ball and hitch are aligned and that the trailer
hitch has proper clearance above the ball. Use
the tongue jack as needed.
CAUTION
Obtain, read and obey all recommendations set
forth by the tow vehicle manufacturer before
attempting to transport equipment. Verify that
equipment weight does not exceed the vehicle’s
towing capacity. Exceeding the tow vehicle’s
rated capacity may result in damage to tow
vehicle or boom lift.
The key switch is in the OFF position. Remove
the key.
The parking brake is disengaged.
The trailer tires are adequately and evenly
inflated.
Periodically check the wheel nut torque according to
manufacturer’s recommendations. Frequent torque
checks are required when a wheel is recently
installed.
Prior to towing, while the trailer wheels are elevated
for boom lift operation, inspect for loose wheels and
for wheel lug wear. If a loose wheel mounting is
suspected, remove and inspect wheel lugs for
damage. NEVER tow a boom lift with worn or
damaged wheel components.
Lift release lever and lower the hitch onto the
ball using the tongue jack. Push down the
release lever to secure the ball.
Use the tongue jack to verify secure coupling. If
using the jack will raise the bumper of the tow
vehicle 2-3 inches, the ball hitch coupling is
secure.
Release the trailer parking brake.
23
BIL-JAX 5533A
BOOM LIFT TRANSPORT
LIFTING INSTRUCTIONS
TRANSPORT INSTRUCTIONS
Refer to Figure 3-9.
Refer to Figure 3-9.
Completely lower and retract boom.
Verify that truck or trailer is parked on a firm and
level surface.
Secure boom travel latches.
Completely lower and retract boom.
Remove all loose materials from machine.
Secure boom travel latches.
Retract all outriggers to fully stowed position.
Retract all outriggers to fully stowed position.
Attach rigging only to the designated forklift
pockets (A).
Load boom onto truck or trailer.
Adjust rigging to keep the machine level and to
minimize the risk of damage to machine.
Chock the wheels (B) and apply parking brake.
Place a wooden block under the tongue, near
the trailer hitch (C).
When using a forklift, use only the designated
forklift pockets. Follow all forklift operating
instructions as indicated by the forklift
manufacturer.
Lower jack until trailer tongue rests on the
wooden block. Swing up and lock the jack (D) so
that the weight of the tongue now rests on the
wooden block.
Only trained and authorized personnel should
attempt to lift the boom using a crane or forklift.
Secure the boom lift to the trailer bed using
straps or chains. Use only the two attachment
points beneath the machine, adjacent to the
outriggers (E).
Adjust as necessary to prevent damage to
rigging or machine.
A
C
D
E
B
Figure 3-19. Lift and Transport Instruction
24
E
4
OPERATOR SERVICE
Performing the appropriate maintenance procedures will extend the life
of the boom lift and will help ensure the safety of personnel operating the
equipment.
Repair, replacement or adjustment of any hydraulic or electrical control
device should be performed only by fully trained and authorized
personnel. These include, but are not limited to, hydraulic load valves,
hydraulic flow control valves, solenoid valves and limit switches. These
are safety related controls. Improper adjustment or tampering with these
devices may impair boom lift function and result in safety or damage
hazards.
Persons performing maintenance or repairs on the machine should be
trained in accordance with the manufacturer’s recommendations.
Contact your regional Bil-Jax representative if additional information is
needed.
Critical or suspect areas identified during any scheduled inspection of the
machine shall be examined by qualified personnel in accordance with
applicable government regulations.
Never operate the machine if a defect or malfunction is identified or
suspected. All defects and malfunctions must be repaired, and all
maintenance performed, before returning a machine to service.
This manual contains a list of recommended maintenance procedures to
be performed daily, weekly and monthly. Refer to the appropriate
Summit Series Parts and Service Manual for a list of annual service
checks.
It is the practice of Bil-Jax, Inc. to issue Service and/or Safety Bulletins,
which may include updates to the information contained in this manual.
In such instances, procedures contained in Bil-Jax Service Bulletins or
Safety Bulletins supersede the information contained in manuals.
Always follow maintenance schedule, regardless of use.
25
BIL-JAX 5533A
DAILY SERVICE CHECKS
The following Maintenance Procedures should be
performed daily or before each operation.
Verify that all decals are correctly applied and in
plain view.
Refer to Section 5 for decal locations.
Verify that all controls and indicators at ground
and platform control stations operate properly.
Lower outriggers to level the boom lift.
Raise and extend all booms.
Press emergency STOP button.
Verify that boom down limit switches operate
correctly.
Down limit switches are actuated when the boom is in
a fully lowered, stowed position. Limit switches must
be operational to raise or lower outriggers.
If outrigger controls are unresponsive when boom is
fully lowered and stowed, inspect down limit switches
for loose mounting or visible damage.
Repair or replace as needed.
Verify that outrigger safety interlocks operate
correctly.
Pull out STOP button and lower the booms.
Begin with the outriggers fully extended and the boom
lift level. Raise one outrigger until the footpad is not in
contact with the ground.
If either control station is unresponsive, refer to Table
4-1 for troubleshooting procedures.
Verify that boom functions are unresponsive when
one outrigger is raised.
If display panel displays an error code, refer to Table
4-2 for error code definitions.
Repeat this procedure for each outrigger.
Verify that booms remain elevated and do not drift.
Verify operation of running and brake lights.
Verify correct tire inflation.
In cold climates, inflate tires to 55 psi.
Inspect tires for damage or loose or missing lug
nuts.
Repair or replace as necessary.
Inspect structural components and platform for
obvious damage or debris.
Raise all outriggers until the footpads are not in
contact with the ground. Verify that all outrigger status
LEDs on the ground control panel are unlit.
Lower one outrigger until the footpad makes contact
with the ground and the outrigger begins lifting the
trailer.
If the LED is lit before the footpad makes contact with
the ground or if the LED remains unlit after the weight
is transferred to the outrigger, the position switch or
wiring is faulty.
Repeat this procedure for each outrigger.
Repair or replace as needed. Refer to Figure 4-1.
Inspect machine for missing, loose or damaged
fasteners, including pins and bolts.
Figure 4-1. Outrigger Position Switches
26
4 – OPERATOR SERVICE
Inspect hydraulic system and fluid levels.
Check all hydraulic hoses and fittings for leaks and
damage. Tighten or replace as necessary to prevent
hydraulic oil or pressure loss.
The hydraulic oil level should be checked with the
booms down, all outriggers raised and the trailer
wheels on a level surface.
Hydraulic oil level should be visible in, but not above,
the sight gauge.
If the hydraulic oil level is not visible to at least half
way up the sight gauge (Figure 4-2), add clean
hydraulic fluid as necessary while all booms and
outriggers are fully retracted and stowed. Pour slowly
to avoid creating air pockets in the reservoir. Do not
fill above sight gauge. Overfilling the hydraulic
reservoir may cause damage to hydraulic lines and
may result in equipment malfunction.
CAUTION
Do not mix hydraulic oils. Do not add any fluid to
the hydraulic system that is not expressly
recommended by the manufacturer. Adding
unauthorized fluids to the hydraulic system may
cause damage to equipment
The hydraulic reservoir is originally filled with Dexron
III/Mercon ATF with a viscosity rating of 175.
Manufacturer recommends a higher viscosity
hydraulic oil when operating equipment routinely in
extreme climates.
1.
2.
Filter Element
Fill Port
3.
Sight Gauge
Figure 4-2. Hydraulic Reservoir
27
BIL-JAX 5533A
WEEKLY SERVICE CHECKS
Perform the following service checks at least once
each week in addition to all recommended Daily
Service Checks:
Check Battery electrolyte level.
If battery charge is low, add enough water to bring the
electrolyte level to the top of the plates.
If batteries are fully charged, raise electrolyte level to
full mark in each cell.
Inspect all electrical wiring.
Check for cuts, loose terminals, broken wires, chaffing
and corrosion.
Repair all damage, remove corrosion and seal
exposed connections.
Inspect transport hitch components for damage.
Inspect boom lift for missing, loose or damaged
hardware.
Inspect all hydraulic system components
including pump and motor and cylinders for
damage, leaks, loss of pressure or speed, and
unusual noise or vibration.
28
MONTHLY SERVICE CHECKS
ADDITIONAL SERVICE INFORMATION
Perform the following service checks at least once
each month:
Refer to the Bil-Jax Parts and Service Manual for a
comprehensive list of Annual service checks.
Clean all battery terminals.
Seals on hydraulic cylinders should be replaced every five
years or as indicated by machine performance.
Check battery for loose connections or damaged
wires.
Verify proper operation of manual lowering
valves and hand pump
Refer to Section 3 for manual boom operating
procedures.
Lubricate all compartment hinges and latches,
slew ring and mating gear.
Use NLGI Grade 2 multi-purpose grease.
Check wheel nut torque.
Refer to Figure 4-3 for correct wheel nut tightening
sequence.
Evenly tighten wheel nuts to 34 N*m in the tightening
sequence shown.
Repeat sequence, tightening wheel nuts to 81 N*m
and to 136 N*m.
NOTE: When wheels are newly installed or
replaced, verify wheel nut torque after 75
and 150 km of travel and monthly
thereafter. Follow this procedure each
time the wheel is removed and
reinstalled.
All service checks should be performed on a machine that
has been stored without use for a period exceeding thirty
days.
Check for air in the hydraulic system if the machine has
been stored without use for a period exceeding thirty days,
or if the machine was stored without use during a
seasonal climate change. Air trapped in the hydraulic
system will affect machine performance. Follow
procedures for bleeding air from the hydraulic system,
found in the Bil-Jax Parts and Service manual.
Owners and lessors should complete a full inspection of all
components and perform a test of all functions, including
brake functions, before commissioning or reselling
machine. Always repair or replace all damaged or
malfunctioning components before commissioning or
reselling machine.
When a change in ownership occurs, it is the responsibility
of the seller to provide the new owner with all manuals for
the machine. It is the responsibility of the buyer to notify
the manufacturer of the unit model and serial number and
the name and address of the new owner within 60 days.
Use the Service Checklists found at the back of this
manual to record all Service Checks as well as any
maintenance, repairs or alterations performed on the
machine.
Records of frequent safety checks need not be made.
However, where a safety hazard is found, it shall be
reported in writing to the owner of the machine, and a
record of any corrective action shall be maintained for five
years or as required b y the authority having jurisdiction.
Refer to the Bil-Jax Parts and Service Manual for a
comprehensive list of Annual service checks.
Figure 4-3. Wheel Nut Tightening Sequence
29
BIL-JAX 5533A
TROUBLESHOOTING
Refer to Table 4-1 for basic troubleshooting operations. Additional information
can be found in the Bil-Jax Parts and Service Manual. Contact the Bil-Jax
Service Department with any questions or before attempting any advanced
troubleshooting operations.
Table 4-1. Troubleshooting Steps
PROBLEM
No lights on panel when
key switch is turned to the
on position.
CAUSE
SOLUTION
a.
Emergency STOP engaged.
a.
Disengage Emergency STOP buttons.
b.
Battery charge is low.
b.
Recharge as needed.
c.
Battery ground or in-series cable is loose.
c.
Inspect and repair battery connections.
d.
Battery main disconnect unplugged.
d.
Plug in main disconnect.
e.
Blown Fuse.
e.
Check and replace fuse.
a.
Fault detected by safety interlock
microprocessor.
a.
Refer to Table 4-2 for error code
definition and correction.
b.
Boom Lift electric or electronic failure
b.
Refer to Table 4-2 for error code
definition and correction.
a.
Key switch turned to the OFF or platform
controls position.
a.
Turn key switch to ground controls
position.
b.
b.
Disengage emergency STOP buttons.
c.
Outriggers not deployed.
c.
Deploy all outriggers.
One or more boom controls
do not function
a.
Key switch is turned to the OFF or
incorrect control position.
a.
Turn key switch to ground or platform
controls position.
OR
b.
Battery charge is low.
b.
Recharge battery.
function improperly
c.
c.
Disengage Emergency STOP buttons.
OR
d.
Battery ground or in-series cable loose.
d.
Inspect and repair battery connections.
function intermittently.
e.
All outriggers not properly deployed.
e.
Deploy all outriggers and level boom lift.
f.
Hydraulic pump inoperative.
f.
Inspect pump; replace or repair as
needed.
g.
Loose wiring connector.
g.
Check wiring terminals in control box
and at valve manifold; replace or repair
as needed.
h.
Valve solenoid not operating properly.
h.
Clean valve solenoid and recheck
function(s); replace or repair as needed.
i.
Fault detected by system interlock.
i.
Check display for system status. Refer
to Table 4-2 for error code definitions
and correction.
j.
Broken or loose wire.
j.
Inspect wiring in control box and at
valve manifold and valve coil; repair or
replace as needed.
Hydraulic function does not
work and display window
shows an error message
Outrigger indicator LED
lights do not function.
30
ERROR CODE DEFINITIONS
The DISPLAY PANEL located on the ground control panel indicates the present
operating status of the boom lift. If an error condition is detected by the control
processor during start-up or operation, the appropriate error code will be
displayed on this panel.
Refer to Table 4-2 for a comprehensive list of Error Code Definitions and
solutions.
Table 4-2. Error Code Definitions
ERROR MESSAGE
DEFINITION OF ERROR
COMMENTS
001 MACHINE IS IN DOWN ONLY Machine was either never leveled, outriggers not
MODE
lowered, or machine went out of level with use.
Retract boom to travel position
and extend outriggers using AUTO
LEVEL button.
002 LOSS OF PLATFORM
COMMUNICATION
Ground control lost communication with platform
control.
Check for unplugged or damaged
platform control cable.
005 PLATFORM CONTROL HAS
STUCK KEY
Platform control detected a stuck or pressed key
on power up.
Turn key switch off and on again
without pressing any buttons.
008 GROUND CONTROL HAS
STUCK KEY
Ground control detected a stuck or pressed key
on power up.
Turn key switch off and on again
without pressing any buttons.
009 BOOM UP WITHOUT
OUTRIGGERS ON GROUND
Ground control detected the boom is up and all
outriggers are not on the ground
Retract boom to travel position
and extend outriggers using AUTO
LEVEL button.
010 LEVEL SENSOR HAS
ERRATIC OUTPUT
The ground control detected an erratic output
from the level sensor.
Retract and extend outriggers
using AUTO LEVEL button.
015 MACHINE IS NOT LEVEL
Machine has gone out of level with use.
Retract and extend outriggers
using AUTO LEVEL.
016 LIFT BOOM
A boom rotate, extend, or retract function
requested with boom down.
Raise boom from travel position.
017 STOW BOOM
An outrigger function requested with boom up.
Retract and lower boom to travel
position.
021 OPEN CIRCUIT PRIMARY UP A load of less than 70mA detected in primary up
circuit on power-up.
Check for faulty boom up
solenoid coil and wiring.
022 SHORTED CIRCUIT
PRIMARY UP
Excessive load detected in primary up circuit on
power-up.
023 OPEN CIRCUIT PRIMARY
DOWN
A load of less than 70mA was detected when
primary down circuit was energized
Check for faulty boom down
024 SHORTED CIRCUIT
PRIMARY DOWN
Excessive load detected when primary down
circuit was energized.
025 OPEN CIRCUIT SECONDARY A load of less than 70mA detected in secondary
UP
up circuit on power-up.
026 SHORTED CIRCUIT
SECONDARY UP
Excessive load detected in secondary up circuit
on power-up.
027 OPEN CIRCUIT SECONDARY A load of less than 70mA detected when
DOWN
secondary down circuit was energized
028 SHORTED CIRCUIT
SECONDARY DOWN
Excessive load detected when secondary down
circuit was energized.
029 OPEN CIRCUIT JIB UP
A load of less than 70mA detected in jib up circuit
on power-up.
Check for faulty jib up solenoid
coil and wiring.
030 SHORTED CIRCUIT JIB UP
Excessive load detected in jib up circuit on
power-up.
Check for faulty jib up solenoid
coil and wiring.
31
BIL-JAX 5533A
ERROR MESSAGE
DEFINITION OF ERROR
COMMENTS
031 OPEN CIRCUIT JIB DOWN
A load of less than 70mA detected when jib down
circuit was energized
Check for faulty jib down solenoid
coil and wiring.
032 SHORTED CIRCUIT JIB
DOWN
Excessive load detected when jib down circuit
was energized.
Check for faulty jib down solenoid
coil and wiring.
033 OPEN CIRCUIT EXTEND
A load of less than 70mA detected in extend
Check for faulty boom extend
solenoid coil/wiring.
034 SHORTED CIRCUIT EXTEND Excessive load detected in extend circuit on
power-up.
Check for faulty boom extend
035 OPEN CIRCUIT RETRACT
A load of less than 70mA detected in retract
Check for faulty boom retract
036 SHORTED CIRCUIT
RETRACT
Excessive load detected in retract circuit on
power-up.
Check for faulty boom retract
037 OPEN CIRCUIT PLATFORM
LEVEL UP
A load of less than 70mA detected in platform
level up circuit on power-up.
Check for faulty level up solenoid
coil/wiring.
038 SHORTED CIRCUIT
PLATFORM LEVEL UP
Excessive load detected in platform level up
Check for faulty level up solenoid
coil/wiring.
LEVEL DOWN
level down circuit on power-up.
Check for faulty level down
040 SHORTED CIRCUIT
PLATFORM LEVEL DOWN
Excessive load detected in platform level down
Check for faulty level down
CW
CW circuit on power-up.
Check for faulty boom rotate
042 SHORTED CIRCUIT
PLATFORM CW
Excessive load detected in platform CW circuit
on power-up.
CCW
CCW circuit on power-up.
044 SHORTED CIRCUIT
PLATFORM CCW
Excessive load detected in platform CCW circuit
on power-up.
045 OPEN CIRCUIT TURNTABLE
CW
A load of less than 70mA detected in rotate CW
Check for faulty rotate CW
046 SHORTED CIRCUIT
TURNTABLE CW
Excessive load detected in rotate CW circuit on
power-up.
Check for faulty rotate CW
047 OPEN CIRCUIT TURNTABLE
CCW
A load of less than 70mA detected in rotate CCW
Check for faulty rotate CCW
048 SHORTED CIRCUIT
TURNTABLE CCW
Excessive load detected in rotate CCW circuit on
power-up.
Check for faulty rotate CCW
049 OPEN CIRCUIT OUTRIGGER A load of less than 70mA detected in outrigger
RETRACT
retract circuit on power-up.
Check for faulty outrigger retract
050 SHORTED CIRCUIT
OUTRIGGER RETRACT
Check for faulty outrigger retract
Excessive load was detected when Outrigger
Retract circuit was energized.
051 OPEN CIRCUIT OUTRIGGER A load of less than 70mA detected in outrigger
EXTEND
retract circuit on power-up.
Excessive load was detected in outrigger extend
Check for faulty outrigger extend
053 OPEN CIRCUIT
LF OUTRIGGER
A load of less than 70mA detected in left front
outrigger circuit on power-up.
Check for faulty solenoid
coil/wiring at outrigger.
054 SHORTED CIRCUIT
LF OUTRIGGER
Excessive load was detected in left front
055 OPEN CIRCUIT
RF OUTRIGGER
A load of less than 70mA detected in right front
052
32
SHORTED CIRCUIT
OUTRIGGER EXTEND
Check for faulty outrigger extend
ERROR MESSAGE
DEFINITION OF ERROR
COMMENTS
056 SHORTED CIRCUIT
RF OUTRIGGER
Excessive load detected in right front outrigger
057 OPEN CIRCUIT
LR OUTRIGGER
A load of less than 70mA detected in left rear
058 SHORTED CIRCUIT
LR OUTRIGGER
Excessive load detected in left rear outrigger
059 OPEN CIRCUIT
RR OUTRIGGER
A load of less than 70mA detected in right rear
060 SHORTED CIRCUIT
RR OUTRIGGER
Excessive load detected in right rear outrigger
069 OPEN CIRCUIT
PROPORTIONAL
A load of less than 70mA detected in proportional
valve circuit on power-up.
coil/wiring at proportional valve.
070 SHORTED CIRCUIT
PROPORTIONAL
Excessive load detected in proportional valve
coil/wiring at proportional valve.
33
BIL-JAX 5533A
34
5 DECAL REPLACEMENT
Decals contain information that is required for the safe and proper use of
the aerial work platform. Decals should be considered necessary
components of the machine and should be checked before each use to
verify that they are correctly attached and legible.
Use the following guides to find the correct location of all decals.
35
BIL-JAX 5533A
Table 5-1. Decal Descriptions
Decal No.
Decal Description
Qty
0202-0523
Made in USA
1
B06-00-0034
DANGER: Electric Shock
1
B06-00-0037
Lubricate Semi-Annually
1
B06-00-0062
NOTICE: AC Power
B06-00-0068
Decal No.
Decal Description
Qty
B06-00-0494
NOTICE: Hazardous Materials
1
B06-00-0495
CAUTION: Compartment Access
Restricted
2
2
B06-00-0496
CAUTION: Generator Plate
Capacity 200 lbs.
1
NOTICE: Hydraulic System Oil
1
B06-00-0503
NOTICE: Handle Applications
1
B06-00-0161B
Bil-Jax Logo, 6” Black Transfer
2
B06-00-0504
NOTICE: Emergency Hand Pump
1
B06-00-0173
NOTICE: Fall Protection
Attachment Point
2
B06-00-0505
DANGER: Before Use/Main
Instruction/Hazards (ground)
1
B06-00-0403
NOTICE: Emergency Lowering
4
B06-00-0521
DANGER: Tip Over Hazard
7
B06-00-0404
WARNING: Outrigger Crush Toe
8
B06-00-0405
WARNING: Pinch Point
17
B06-00-0533
WARNING: Operating Instructions
(Ground)
2
B06-00-0471
DANGER: Before Use/Main
Instruction/Hazards (Platform)
1
B06-00-0534
WARNING: Operating Instructions
(Platform)
1
B06-00-0473
NOTICE: Operator’s Manual
Missing
1
B06-00-0537
NOTICE: Range of Motion
2
B06-00-0540
5533A, 6” Black Transfer
2
B06-00-0474
NOTICE: Max. Load
1
B06-00-0541
1
CAUTION: Manual Boom
Functions
1
B06-00-0475
WARNING: Read/Understand
Operator’s Manual
B06-00-0542
WARNING: Max. Towing Speed
2
B06-00-0477
WARNING: Forklift Pockets
2
B06-00-0543
WARNING: Wheel Crush Toe
2
B06-00-0478
NOTICE: Platform Charger/Power
Plug Here
1
B06-00-0544
WARNING: Towing Hazards
2
B06-00-0481
CAUTION: Transport Safety Latch
3
B06-00-0545
Bil-Jax Website Transfer
2
B06-00-0482
DANGER: Electrocution Hazard
2
B06-00-0550
WARNING: Unhitch Lift Before Use
2
B06-00-0484
DANGER: Battery/Charger Safety
1
B06-00-0551
CAUTION: Prior to Towing
1
Identification Plates
B06-00-0490
VIN Plate
1
B06-00-0499
ANSI ID Plate
1
B06-00-0524
Annual Inspection Plate
1
B06-00-0526
Key Tag
1
CE/CAN/AUS Machines
36
B06-00-0167
Black/Yellow Hazard - 2” Wide
4
B06-00-0568
WARNING: Tip Over Hazard
4
0542
0405
0521
0551
0550
0544
0481
0496
0403
0405
161B
0478
0405
4x
2x
0543
0545
0034
0484
0540
0537
0550
0477
0495
0404
0521
0505
0521
0481
0533
0403
0405
0037
0403
0482
0405
0484
0537
0471
0474
0534
0568
0503
0473
0167
4x
0504
0552
0541
0068
0202-0523
0062
0475
0494
BIL-JAX 5533A
Figure 5-1. Decal Placement
37
BIL-JAX 5533A
38
6 ANSI REPRINT
The following sections are reprinted from the ANSI A92.2-2001 code in
effect at the time of manufacture and govern the safe use of the Bil-Jax
Model 5533A Telescoping Boom Lift. It is the responsibility of all
owners and operators of this machine to read, understand and obey
the recommendations set forth by the ANSI code.
Permission to reprint this material has been granted by the Scaffold
Industry Association.
7.
7.1
General Responsibilities. Each dealer or installer as
applicable shall comply with the requirements of this
section.
7.2
Vehicle Specifications. Each dealer or installer, or both,
who sells an aerial device shall inform the owner or user, or
both, of the manufacturer’s minimum vehicle specifications.
7.3
Vehicle Weight Distribution. The installer shall be
responsible for the weight distribution of the completed
mobile unit in accordance with the requirements of the
aerial device and the applicable regulations. Allowance
shall be made for the weight of readily removable tools and
material specified by the user.
7.4
7.5
device. The training shall be offered initially and
subsequently on request.
Responsibilities of Dealers and Installers
Manuals. Upon delivery of the equipment to the owner or
user, the dealer or installer shall provide the manuals as
required by Paragraph 6.4 of this standard and manuals for
auxiliary equipment added by the installer.
Installations. The installer shall comply with Sections 5 and
6 of this standard relating to proper installation and shall
follow the instructions of the manufacturer. In the event the
original manufacturer no longer exists, an equivalent entity
may provide these instructions. The installer of an aerial
device shall, before the mobile unit is placed in operation,
perform stability tests in accordance with the requirements
of 4.5.1 and 4.5.2, the operational and visual tests in
accordance with the requirements of 6.6.1 and 6.6.2 a, and
the appropriate electrical tests required in 5.4.3 of this
standard. The installer shall, when installing an aerial
device on a chassis which is a highway vehicle, comply with
all requirements of the Federal Motor Vehicle Safety
Standards in effect at the time of installation. Certification as
a manufacturer (alteration, intermediate or final) of a motor
vehicle under the Federal Motor Vehicle Safety Standards
is required. The travel height of a mobile unit shall be
posted in a location that is readily visible to the vehicle
operator. For insulated aerial devices, the installer shall
assure conformance to the Qualification test requirements
of 5.3.2 by either obtaining certification of the test and
performing a periodic test after insulation, or by performing
the Qualification test.
7.5.1
Quality Assurance. The installer shall have a documented
quality assurance program which will ensure compliance
with this standard.
7.6
Welding. All welds made by the installer, whose failure
could result in motion of the platform(s) shall meet the
Structural Welding Code AWS D1.1-98 and AWS D1.2-98.
The installer shall establish applicable welding quality
assurance procedures for all weldments.
7.7
Training. The dealer or installer shall offer training or
training materials that aid owners and users in the
operation, inspection, testing and maintenance of the aerial
7.7.1 Dealer or Installer as User. Whenever a dealer or installer
directs personnel to operate the aerial device (inspecting,
sales demonstrations, or any form of use), the dealer or
installer shall assume the responsibilities of users as
specified in Section 9 of this standard. All personnel
authorized to operate this aerial device shall have been
trained.
8.
Responsibilities of Owners
8.1
General Responsibilities. Each owner shall comply with the
requirements of this section. The following responsibilities
pertain to the owner’s inspection, testing, maintenance,
modification, training and transfer of ownership. These
activities shall be performed by qualified person(s).
8.2
Inspection and Testing Classifications.
8.2.1 Initial Inspection and Test. Prior to initial use, all new or
modified mobile units shall be inspected and tested to ensure
compliance with the provisions of this standard. Verification
by the manufacturer, the installer, or an equivalent entity(s)
meets this requirement.
8.2.2 Regular Inspection and Tests. The inspection procedure for
mobile units is divided into two classifications based upon the
intervals at which inspections and tests shall be performed.
Intervals shall be set by the owner in accordance with the
manufacturer’s recommendations. Such intervals are
dependant upon component function and exposure to wear,
deterioration and other agents which adversely affect
component life. Two classifications are designated:
(1) Frequent Inspection and Test: Daily to Monthly intervals.
(2) Periodic Inspection and Test: One to Twelve Month
intervals.
8.2.3 Frequent Inspection and Test. Items determined to by the
owner in accordance with the manufacturer’s
recommendations for each specific aerial device shall be
inspected for defects. The following tests and inspections
shall be performed by the operator once daily, prior to first
use:
(1) Operating controls and associated mechanisms for
conditions interfering with proper operation.
(2) Visual and audible safety devices for malfunction.
(3) Hydraulic and pneumatic systems for observable
deterioration or excessive leakage.
(4) Fiberglass and other insulating components for visible
damage or contamination.
(5) Missing or illegible operational and instructional
markings.
(6) Electrical systems of/or related to the aerial device for
malfunction, signs of excessive deterioration, dirt and
moisture accumulation.
(7) Visual inspection of bolts, pins and other fasteners for
loose, deformed or missing fasteners and other locking
39
BIL-JAX 5533A
devices. Any suspected items shall be carefully
examined or tested and a determination made by a
qualified person as to whether they constitute a safety
hazard. All unsafe items shall be replaced or repaired
before use.
8.2.4 Periodic Inspection or Test. An inspection of the mobile unit
shall be performed at the intervals defined in 8.2.2 depending
upon its activity, severity of service, and environment, or as
specifically indicated below. (These inspections shall include
the requirements of 8.2.3):
(1) Structural members for deformation, cracks or corrosion.
(2) Parts, such as pins, bearings, shafts, gears, rollers,
locking devices, chains, chain sprockets, wire and
synthetic ropes and sheaves, for wear, cracks or
distortion.
(3) Hydraulic and pneumatic relief valve settings.
(4) Hydraulic system for proper oil level.
(5) Hydraulic and pneumatic fittings, hoses and tubing for
evidence of leakage, abnormal deformation or excessive
abrasion.
(6) Compressors, pumps, motors and generators for loose
fasteners, leaks, unusual noises or vibrations, loss of
operating speed and excessive heating.
(7) Hydraulic and pneumatic valves for malfunction and
visible cracks in the external valve housing, for leaks
and sticking spools.
(8) Visually inspect any vacuum prevention systems and
verify function of such systems on Category “A” aerial
devices.
(9) Hydraulic and pneumatic cylinders and holding valves
for malfunction and visible damage.
(10) Hydraulic and pneumatic filters for cleanliness and the
presence of foreign material in the system indicating
other component deterioration.
(11) Electrical systems and components for deterioration or
wear including those not readily visible on a frequent
inspection.
(12) Performance test of all boom movements.
(13) Condition and tightness of bolts and other fasteners.
(14) Welds, as specified by the manufacturer.
(15) Legible and proper identification, operational and
instructional markings.
(16) If the aerial device is rated as an insulated device, the
electrical insulating components and system(s) shall be
thoroughly inspected for lack of cleanliness and other
components that compromise insulation. Then these
components and system(s) shall be tested for
compliance with the rating of the aerial device in
accordance with one of the applicable methods and
procedures as outlined in Section 5.4.3 of this standard:
(a) If the aerial device is used for AC bare-hand work,
the unit shall undergo a 60 Hz test as shown in
Table 2 at least every three years;
(b) If the aerial device is used for DC bare-hand work,
the unit shall undergo a DC test as shown in Table
2 at least every three years.
(c) After repair or modification of any component that
crosses the insulating system(s), or the repair or
replacement of an insulating component(s), the unit
shall be dielectrically tested in accordance with
section 5.4.3;
(d) An insulated replacement boom shall be tested to
insure conformance to 5.3.3 by the supplier;
(e) Bare-hand work units shall be tested as shown in
Table l after any major repair to the insulated boom
or any insulated boom replacement. Any suspected
items shall be carefully examined or tested and a
determination made by a qualified person as to
whether they constitute a safety hazard. All unsafe
items shall be replaced or repaired before use.
(1)
(2)
8.4.1.1 Maintenance. Maintenance and frequency of maintenance
shall be determined by the owner in accordance with the
manufacturer’s recommendations. Welding repairs of
components or welds, designated as critical in the
manufacturers manual, shall be made in accordance with
the manufacturers recommendations. Should the original
manufacturer no longer exist an equivalent entity may
determine the required procedure.
8.4.1.2 Maintenance Training. The owner shall train their
maintenance personnel in inspection and maintenance of
the aerial device in accordance with the manufacturer’s
recommendations and Section 8 of this standard.
8.4.1.3 Modifications. No modifications or additions which affect
the stability, mechanical, hydraulic, or electrical integrity or
the safe operation of the aerial device shall be made
without the written approval of the manufacturer. If such
modifications or changes are made, the capacity, operation,
and maintenance instruction markings shall be changed
accordingly. In no case shall the safety factors be reduced
below those specified in this standard or below the
manufacturers design safety factors, whichever are greater.
Should the original manufacturer no longer exist, an
equivalent entity may approve required modification.
8.6
Weight Distribution. Changes in loading or additions made
to the mobile unit after the final acceptance that affect
weight distribution shall meet applicable regulations by
governmental agencies. In no case shall axle loads of the
fully loaded vehicle exceed the Gross Axle Weight Ratings
(GAWR) assigned by the manufacturer. Note: Any change
in weight distribution may adversely affect stability.
8.7
Transfer of Ownership. When a change in ownership of an
aerial device occurs, it shall be the responsibility of the
seller to provide the manufacturer's manual(s) for that aerial
device to the purchaser. It is the responsibility of the
purchaser to notify the manufacturer of the unit model and
serial number and the name and address of the new owner
within 60 days.
8.8
Markings. The markings on the aerial device shall not be
removed, defaced, or altered. All missing or illegible
markings shall be promptly replaced.
8.9
Parts. When parts or components are replaced they shall
be identical in specification and function to the original
aerial device parts or components or shall provide an equal
or greater factor of safety.
8.10
Safety Bulletins. Owners shall comply with safety related
bulletins as received from the manufacturer, dealer or
installer.
8.11
Manuals. The owner shall insure that the operating
manual(s) is stored on the mobile unit.
8.12
8.3
40
Inspection and Test Records.
Items to be inspected shall be designated to the
operator or other authorized person making frequent
inspections. Records of frequent inspections need not
be made. However, where a safety hazard is found, it
shall be reported in writing to a person responsible for
the corrective action and that report and a record of
the correction shall be maintained for five years, or as
required by applicable regulations.
Written, dated and signed reports and records shall be
made of periodic inspections and tests and retained for
a period of five years or as required by applicable
regulations.
Training, Retraining, and Familiarization of Operators.
6 — ANSI REPRINT
8.12.1 Owner as a Renter or Lessor. When an owner functions
as a renter or lessor he shall have the same responsibilities
as specified under Section 11 of this standard.
8.12.2 General Training. Only personnel who have received
general instructions regarding the inspection, application
and operation of aerial devices, including recognition and
avoidance of hazards associated with their operation, shall
operate an aerial device. Such items covered shall include,
but not necessarily be limited to, the following issues and
requirements:
(1) The purpose and use of manuals.
(2) That operating manuals are an integral part of the
aerial device and must be properly stored on the
vehicle when not in use.
(3) A pre-start inspection.
(4) Responsibilities associated with problems or
malfunctions affecting the operation of the aerial
device.
(5) Factors affecting stability.
(6) The purpose of placards and decals.
(7) Workplace inspection.
(8) Applicable safety rules and regulations, such as Part 4,
ANSI C2-1997, National Electrical Safety Code
(applies to utility workers as defined in ANSI C2). The
above standard is an example; other industries using
aerial devices have safety rules pertinent to that
industry.
(9) Authorization to operate.
(10) Operator warnings and instructions.
(11) Actual operation of the aerial device. Under the
direction of a qualified person, the trainee shall operate
the aerial device for a sufficient period of time to
demonstrate proficiency in the actual operation of the
aerial device.
(12) Proper use of personal fall protection equipment.
8.12.3 Retraining. The operator shall be retrained, when so
directed by the user, based on the user’s observation and
evaluation of the operator.
(4)
Responsibilities associated with problems or
device.
ANSI C2-1997, National Electrical Safety Code.
(Applies to utility workers as defined in ANSI C2). The
industry.
aerial device.
9.3.2
Retraining. The operator shall be retrained, when so
9.3.3
Familiarization. When an operator is directed to operate an
aerial device he/she is not familiar with, the operator, prior
to operating, shall be instructed regarding the following
items and issues:
(1) The location of the manuals.
(2) The purpose and function of all controls.
(3) Safety devices and operating characteristics specific to
the aerial device.
9.4
Application. The employer and assigned operator shall
insure that the aerial device is used only for intended
applications as defined in the operating manual, and that
recognized safety practices are observed.
9.5
Mobile Operation. Before and during driving, the driver
shall:
(1) Avoid traveling on any surface that adversely affects
vehicle stability.
(2) Maintain a safe distance from obstacles and overhead
lines.
(3) Maintain communications between the driver and the
operator.
(4) Under all travel conditions, the driver shall limit travel
speed in accordance with conditions of the ground
surface, congestion, and slope.
9.6
Alterations. Altering or disabling of safety devices, guards,
or interlocks if so equipped shall be prohibited.
9.7.1
Bare-Hand Work. For bare-hand work, a Category “A”
aerial device shall be used.
9.8
Lower Controls. The lower controls of aerial devices shall
not be used for continuous operation with personnel in the
platform.
10.
Responsibilities of Operators
10.1
General Responsibilities. Each operator shall comply with
the requirements of this section.
10.2
Operation. During operation of the aerial device all platform
occupants shall use appropriate fall protection connected to
the aerial device at the platform position.
10.3
Work Platform. The operator shall not use railings, planks,
ladders or any other device in or on the work platform for
achieving additional working height or reach.
8.12.4 Familiarization. When an operator is directed to operate an
items and issues:
the aerial device.
9.
Responsibility of Users.
9.1
General Responsibilities. Each User shall comply with the
requirements of this section.
9.2
Personnel. Only trained and authorized personnel shall be
permitted to operate the aerial device.
9.3
9.3.1
General Training. Only personnel who have received
requirements:
41
BIL-JAX 5533A
10.4
Brakes. The vehicle parking brake(s) shall be set at all
times that the boom is elevated except when the aerial
device is being used in accordance with 9.5.
10.5
Loading. Any loading which includes a horizontal load shall
be avoided unless the mobile unit is designed for that
application.
10.6
Observations. Observations during operation for any
defects shall be conducted on an ongoing basis.
10.6.1 Pre-start Inspection. Items determined by the owner in
accordance with the manufacturer’s recommendations for
each specific aerial device shall be inspected for defects
prior to each day’s operation. The following tests and
inspections shall be performed by the operator once daily,
prior to first use:
(1) Operating controls and associated mechanisms for
conditions interfering with proper operation.
(2) Visual and audible safety devices for malfunction.
(3) Hydraulic or pneumatic systems for observable
deterioration or excessive leakage.
(4) Fiberglass and other insulating components for visible
damage or contamination.
(5) Missing or illegible operational and instructional
markings.
(6) Electrical systems of/or related to the aerial device for
malfunction, signs of excessive deterioration, dirt and
moisture accumulation.
(7) Visual inspection of bolts, pins, and other fasteners for
loose, deformed or missing fasteners and other locking
devices. Any suspected items shall be carefully
examined or tested and a determination made by a
qualified person as to whether they constitute a safety
hazard. All unsafe items shall be replaced or repaired
before use.
10.7
10.8
Worksite. Before the aerial device is used the worksite shall
be surveyed for hazards such as:
(1) Untamped earth fills.
(2) Ditches.
(3) Drop-offs and floor obstructions.
(4) Debris.
(5) Overhead obstructions and electrical conductors.
(6) Weather conditions.
(7) Presence of unauthorized persons.
Precautions. Before and during each use the operator shall:
(1) Check for overhead obstructions and electrical
conductors.
(2) Insure that the load on the platform and/or load lifting
devices are in accordance with the manufacturer's
rated capacity.
(3) Insure that outriggers and stabilizers are used if the
manufacturer's instructions require their use.
(4) Insure that guardrails are properly installed, and the
gates are closed.
(5) Use outrigger pads when necessary to provide firm
footing.
10.9
Mobile Operation. Before engaging in mobile operation the
operator shall determine that the aerial device is specifically
designed for mobile operation.
10.10
Personnel. Only trained and authorized personnel shall be
permitted to operate the aerial device.
10.11
42
requirements:
device.
industry.
aerial device.
10.11.2 Retraining. The operator shall be retrained, when so
items and issues:
the aerial device.
Responsibilities of Renters, Lessors or Lessees
11.1
General Responsibilities. Each renter or lessor or lessee
shall comply with the requirements of the applicable section
or sections below.
11.1.1 Lessor or Lessee as Dealer or Installer. When a lessor or
lessee uses the aerial device as a dealer or installer he
shall have the same responsibilities as specified under
Section 7 of this standard.
11.1.2 Lessor or Lessee as Owner. When a lessor or lessee
uses the aerial device as an owner he shall have the same
responsibilities as specified under Section 8 of this
standard.
11.1.3 Lessor or Lessee as User. When a lessor or lessee uses
the aerial device as a user he shall have the same
responsibilities as specified under Section 9 of this
standard.
11.1.4 Lessor or Lessee as Operator. When a lessor or lessee
uses the aerial device as an operator he shall have the
same responsibilities as specified under Section 10 of this
standard.
11.2
Ownership Duties. The renter or lessor shall carry out the
duties of ownership specified in this standard which are not
assigned to the renting entity or lessee as the user.
6 — ANSI REPRINT
11.3
Obligations. Upon delivery each renter or lessor of an
aerial device shall provide the operators manual and the
ANSI/SIA A92.2-xxxx Manual of Responsibilities for dealers,
owners, users, operators, lessors and lessees of Vehicle
Mounted Elevating and Rotating Aerial Devices. These
manuals shall be stored on the mobile unit.
11.4
Training. The renter or lessor shall offer training or training
materials that aid the renting entity or lessee in the
operation, inspection, testing and maintenance of the aerial
device. This training shall be offered initially and
subsequently on request.
requirements:
device.
(8)
Applicable safety rules and regulations, such as Part 4,
industry.
aerial device.
aerial device he/she is not familiar with, the operator, prior to
operating, shall be instructed regarding the following items
and issues:
the aerial device.
11.5
Communications. In the event the manufacturer or installer
provides the renter or lessor manuals, bulletins, or other
materials for the information of the user of an aerial device,
the renter or lessor shall pass them on to the user without
any undue delay.
DENOTES
PROHIBITED
ZONE
Figure 6-1. Minimum Safe Approach Distances
Do not allow machine, personnel, or conductive
materials inside prohibited zone. Maintain
M.S.A.D. from all energized lines and parts as
well as those shown. Assume all electrical parts
and wires are energized unless known
otherwise.
Diagrams shown are only for purposes of
illustrating M.S.A.D. work positions, not all work
positions.
Voltage Range
Minimum Safe Approach Distance
(Feet)
0 to 300V
(Meters)
Avoid Contact
Over 300V to 50KV
10
3.05
Over 50KV to 200KV
15
4.60
Over 200KV to 350KV
20
6.10
Over 350KV to 500KV
25
7.62
Over 500KV to 750KV
35
10.67
Over 750KV to 1000KV
45
13.72
43
BIL-JAX 5533A
44
7
MATERIAL SAFETY
The following Material Safety Data Sheets describe the correct
procedures for the safe handling of chemical components within the
Model 5533A Telescoping Boom Lift, as well as any potential health and
safety hazards related to these chemicals. Material Safety Data Sheets
are included here in accordance with applicable federal and state
regulations. Read and observe all safety precautions. Maintain
awareness of potential health and safety hazards.
MATERIAL SAFETY DATA SHEET
FOR LEAD ACID BATTERIES, WET, FILLED WITH ACID
SECTION I – GENERAL INFORMATION
Manufacturer’s Name:
Street Address:
City, State, Zip
Phone Number:
Crown Battery Mfg. Company
1445 Majestic Drive
Fremont, Ohio 43420
419 334-7181
EMERGENCY NO: 800 487-2879
OR
800 OIL-TANK
REVISION DATE:
5/18/2000
OTHER LIMITS
CAS NUMBER
SECTION II -- MATERIAL IDENTIFICATION AND INFORMATION
COMPONENTS
Hazardous Components
1% or greater
Carcinogens 0.01% or greater
PERCENT
OSHA
PEL
ACGIH
TLV
METALLIC LEAD METAL
LEAD SULFATES
LEAD OXIDES
POLYPROPYLENE CASE MTL
SEPARATORS
SULFURIC ACID (H2SO4)
WATER
25.5%
18.2%
18.0%
6.4%
3.5%
5.2%
19.2%
0.05 mg/m3
0.05 mg/m3
0.05 mg/m3
0.05 mg/m3
0.05 mg/m3
0.05 mg/m3
NONE
NONE
NONE
7439-92-1
7439-92-1
7439-92-1
1.0 mg/m3
1.0 mg/m3
NONE
7664-93-9
REGULATORY INFORMATION:
Those ingredients listed above are not subject to the reporting requirements of 313
of Title III of the Superfund Amendments and Reauthorization Act. The items are
covered in an exemption as a “Manufactured Article”. 372.30(b)
SECTION III -- PHYSICAL / CHEMICAL CHARACTERISTICS
Boiling Point
Vapor Pressure
Solubility in Water
Specific Gravity
Appearance & Odor
Approximately 203F
Vapor Density:
14 @ 37% @ 80 F
Melting Point:
100%
Water Reactive:
1.245 - 1.295 Battery Electrolyte
Clear Liquid with Sharp Pungent Odor
Greater Than 1
-36 F to -10.6 F
Yes, Produces Heat
SECTION IV -- FIRE AND EXPLOSION HAZARD DATA
Flash Point: Not Combustible
Auto Ignition Temperature N/A
Flammability Limits in Air % by Volume:
N/A
Extinguishing Media: Dry Chemical Carbon Dioxide, Water Fog, Water
Special Fire Fighting Procedures: Sulfuric Acid Fumes, Sulfur Dioxide Gas or Carbon Monoxide may be
released when acid decomposes. Wear NIOSH approved self-contained breathing apparatus.
Unusual Hazards: Water applied to sulfuric acid generates heat and causes acid to splatter. Wear full-cover
acid resistant clothing. Sulfuric acid reacts violently with metals, nitrates, chlorates, carbides, fulminates,
picrates and other organic materials. Reacts with most metals to yield explosive/flammable hydrogen gas.
This reaction is intensified when sulfuric acid is diluted with water to form battery electrolyte.
45
BIL-JAX 5533A
FOR LEAD ACID BATTERIES, WET, FILLED WITH ACID (Continued)
SECTION V -- HEALTH HAZARD DATA
Primary Routes of Entry:
Inhalation: YES
Skin:
YES
Ingestion: YES
Acute
EYES, SKIN, RESPIRATORY SYSTEM & DIGESTIVE SYSTEM
Chronic:
EYES, SKIN, RESPIRATORY SYSTEM & DIGESTIVE SYSTEM
IRRITATION OF EXPOSED AREA, BURNS AND RESPIRATORY PROBLEMS
NO POSSIBILITY OF EXPOSURE OF LEAD WILL OCCUR UNLESS
BATTERY IS DESTROYED.
Health Hazards:
Signs and Symptoms of Exposure:
Medical Conditions Generally
Aggravated By Exposure:
EXPOSURE TO MIST MAY CAUSE LUNG DAMAGE & AGGRAVATE
PULMONARY CONDITION.
Emergency First Aid Procedures:
SEEK MEDICAL ASSISTANCE FOR FURTHER TREATMENT, OBSERVATION
AND SUPPORT IF NECESSARY.
Eye Contact:
WASH WITH COPIOUS QUANTITIES OF COOL WATER FOR AT LEAST 15 MINUTES
Skin Contact:
FLUSH AREA WITH LARGE AMOUNTS OF COOL WATER FOR AT LEAST 15 MINUTES
Inhalation:
REMOVE TO FRESH AIR, IF BREATHING IS DIFFICULT - GIVE OXYGEN
Ingestion:
GIVE MILK TO DRINK, DO NOT INDUCE VOMITING. CALL PHYSICIAN
SECTION VI -- REACTIVITY DATA
Stability:
STABLE
Incompatibility:
Hazardous Decomposition Products:
Hazardous Polymerization:
Conditions to Avoid: N/A
AVOID COMBUSTIBLES, ORGANIC MATERIALS, AND STRONG REDUCING AGENTS
SULFUR TRIOXIDE, CARBON MONOXIDE, SULFURIC ACID FUMES, &
SULFUR DIOXIDE
MAY OCCUR
Conditions to Avoid: N/A
SECTION VII -- SPILL OR LEAK PROCEDURES
Steps to be taken in case material is released or spilled:
CONTAIN SPILL, USING NON-COMBUSTIBLE MATERIALS: VERMICULITE, DRY SAND & EARTH. NEUTRALIZE
WITH LIME, SODA ASH, SODIUM BICARBONATE, ETC.
Waste disposal method:
CONSULT STATE ENVIRONMENTAL AGENCY. INDIVIDUAL STATE REGULATIONS VARY
Precautions to be taken in Handling & Storage:
SEPARATE FROM INCOMPATIBLE MATERIALS, KEEP AWAY
FROM FIRE, SPARKS AND HEAT
Other Precautions and/or Special Hazards:
CONTACT WITH METALS MAY PRODUCE TOXIC SULFUR DIOXIDE FUMES & MAY ALSO RELEASE FLAMMABLE
HYDROGEN GAS. THIS REACTION IS INTENSIFIED WHEN DILUTED.
NFPA Rating:
HEALTH: 3
FLAMMABILITY:
0
REACTIVITY:
2
SPECIAL: 0
HMIS Rating:
HEALTH: 3
FLAMMABILITY:
0
REACTIVITY:
2
PERSONAL PROTECTION:
SECTION VIII -- CONTROL AND PROTECTIVE MEASURES
Respiratory Protection:
Protective Gloves:
Eye Protection:
Ventilation:
Other Protective Equipment:
Hygienic Work Practices:
46
ABOVE P.E.L.: NIOSH APPROVED, FITTED, FULL FACE RESPIRATOR
ACID RESISTANT
FULL FACE PROTECTION
LOCAL EXHAUST: VENTILATED AREA PREFERRED
MECHANICAL:
IF BELOW P.E.L.
SPECIAL:
MUST BE ACID & EXPLOSIVE RESISTANT
OTHER:
MUST BE ACID & EXPLOSIVE RESISTANT
ACID RESISTANT CLOTHING AND BOOTS
N/A
X
7 — MATERIAL SAFETY
DEXRON III/MERCON AUTOMATIC TRANSMISSION FLUID (HYDRAULIC OIL)
SECTION I -- GENERAL INFORMATION
TRADE NAME:
EMERGENCY TELEPHONE NUMBERS:
CHEMICAL FAMILY:
CAS NUMBER: MIXTURE.
HAZARDOUS INGREDIENTS:
CITGO TRANSGARD™ ATF, DEXRON III/MERCON
918.495.4700 (medical); 800.424.9300 (chemical)
AUTOMATIC TRANSMISSION FLUID, LUBRICATING OIL
REVISION DATE: 10/29/98
CONTAINS NO INGREDIENTS NOW KNOWN TO BE HAZARDOUS AS
DEFINED IN OSHA 29 CFR 1910.1000 AND OSHA 29 CFR 1910.1200.
SECTION II -- HEALTH HAZARD DATA
PRIMARY ROUTES OF ENTRY:
INHALATION, SKIN ABRASION AND INGESTION.
CARCINOGENIC:
NO
MILD, TRANSIENT SKIN OR EYE IRRITATION MAY OCCUR.
SYMPTOMS (INGESTION, CONTACT, INHALATION):
EYES:
FLUSH WITH WATER FOR 15 MINUTES
SKIN:
WASH THOROUGHLY WITH WARM SOAPY WATER.
INGESTION:
DO NOT INDUCE VOMITTING-SEEK MEDICAL ATTENTION.
CONDITIONS AGGRAVATED BY EXPOSURE:
NONE KNOWN
AIR EXPOSURE LIMITS:
P.E.L. 5 mg/m3 (OSHA) T.L.V. 10mg/m3 (ACGIH)
HEALTH:
0
FIRE:
1
SPECIFIC:
X
REACTIVITY:
0
SECTION III -- PHYSICAL DATA
BOILING POINT/FREEZING POINT:
VAPOR PRESSURE (PSIA):
SPECIFIC GRAVITY (H20=1):
SOLUBILITY IN WATER:
PH OF CONCENTRATE:
APPEARANCE AND ODOR:
N/A
N/A
0.86
NEGLIGIBLE; INSOLUBLE IN COLD WATER
N/A
RED LIQUID, MILD PETROLEUM ODOR
SECTION IV -- FIRE AND EXPLOSION HAZARD DATA
FLASH POINT (METHOD USED):
FLAMMABLE LIMITS:
LEL: N/A
UEL:
EXTINGUISHING MEDIA:
UNUSUAL FIRE AND EXPLOSION HAZARDS:
CLOSED: 339º F (Pensky-Martens); OPEN: 390º F (Cleveland).
NOT DETERMINED
N/A
DRY CHEMICAL, FOAM, CO2, WATER FOG. TREAT AS CLASS B FIRE.
PRODUCES COMBUSTIBLE VAPOR AT TEMPERATURES ABOVE FLASH POINT
SECTION V -- REACTIVITY DATA
STABILITY:
CONDITIONS TO AVOID:
INCOMPATIBILITY (MATERIALS TO AVOID):
HAZARDOUS DECOMPOSITION PRODUCTS:
HAZARDOUS POLYMERIZATION:
STABLE
AVOID EXTREMES OF HEAT; IGNITION SOURCES.
STRONG OXIDIZING MATERIALS.
INCOMPLETE COMBUSTION MAY CAUSE CARBON OXIDES.
WILL NOT OCCUR.
SECTION VI -- SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION (SPECIFIC TYPE):
VENTILATION:
LOCAL EXHAUST:
MECHANICAL EXHAUST (GENERAL):
PROTECTIVE GLOVES:
EYE PROTECTION:
OTHER PROTECTIVE EQUIPMENT:
NONE REQUIRED
NORMAL
NORMAL
X
OIL IMPERVIOUS GLOVES RECOMMENDED
SAFETY GLASSES RECOMMENDED
PROTECTIVE CLOTHING RECOMMENDED
SPECIAL LABELLING INSTRUCTIONS:
SPECIAL PACKAGING RECOMMENDATIONS:
HANDLING AND STORAGE RECOMMENDATIONS:
SPILL OR LEAK PROCEDURES:
NOT REQUIRED
NONE
AVOID EXTREMES OF COLD OR HEAT. STORE IN CLEAN DRY AREA.
IN CASE OF LEAK OR SPILL, DIKE AND ABSORB WITH INERT MATERIAL. FOLLOW
ALL LOCAL, STATE AND FEDERAL REGULATIONS FOR DISPOSAL.
DISCLAIMER: THE INFORMATION CONTAINED HEREIN HAS BEEN COMPILED FROM SOURCES
CONSIDERED TO BE DEPENDABLE AND IS ACCURATE TO THE BEST OF THE SELLER’S
KNOWLEDGE. THE SELLER MAKES NO WARRANTY WHATSOEVER, EXPRESSED OR IMPLIED, REGARDING THE ACCURACY
OF SUCH DATA OR THE RESULTS TO BE OBTAINED FROM THE USE THEREOF.
47
BIL-JAX 5533A
48
8 EQUIPMENT OPTIONS
The Bil-Jax lift may be equipped with one or more optional
components designed for the convenience and safety of
operators when using the equipment to accomplish specific
tasks.
Always use only those components manufactured and/or
authorized by Bil-Jax, Inc. Never make any adjustments or
modifications or otherwise alter the equipment in any way that is
not expressly recommended by the manufacturer.
When operating a machine equipped with optional components,
observe all safety precautions set forth by the manufacturer, as
well as all government codes and regulations regarding this
equipment and its components.
Consult rental agency or equipment manufacturer regarding
which optional components may be installed on the boom lift. For
questions regarding safe use, contact your regional Bil-Jax
dealer before attempting operation
49
BIL-JAX 5533A
MATERIAL LIFTING HOOK
If the boom lift is equipped with a material lifting
hook, observe the following procedure for material
lift operation:
Remove platform controls from the work
platform by releasing the latch on the back of the
platform control box.
Disconnect platform control box from the load
sense module located on the boom lift bulkhead.
Remove the electric loopback plug from the
receptacle on the bottom right of the ground
control panel (Figure 8-1) and insert the platform
control cable into the open receptacle.
Figure 8-2. Material Lifting Hook Installation
Operate the material lifting hook remotely, using
the platform control box for optimal control.
WARNING
Always observe the manufacturer’s weight lifting
limitations when using the material lifting hook.
Always use lifting straps or wire rope slings that
are rated at a minimum 500 lbs lifting capacity.
Never stand beneath an elevated load or position
an elevated load above personnel. Falling
objects can cause serious injury or death.
1. To Boom Cable.
Do Not Remove.
2. To Platform Controls.
Disconnect Platform controls from Load Sense
Module here. Replace with loopback plug from
ground control station. Plug platform controls
into open receptacle on ground control station to
operate Material Lifting Hook.
Figure 8-1. Material Lifting Hook Configuration
Insert the removed electric loopback plug into
the open receptacle on the load sense module,
replacing the platform control cable.
Remove the retaining pin holding the platform to
boom lift. Firmly secure platform to prevent
equipment damage.
Remove the platform from the boom by lifting
cage up and away from the mounting bracket on
the boom nose.
Attach the material lifting hook to the mounting
bracket on the boom nose and insert the
retaining pin (Figure 8-2).
50
DANGER
This machine is not insulated for use near
electrical power lines and DOES NOT provide
protection from contact with or close proximity
to any electrically charged conductor. Operator
must maintain safe clearances at all times and
always allow for platform movement such as
wind-induced sway. Refer to Table 1-1 for
minimum safe approach distances between the
machine and electrical power lines.
Reverse the procedure to reattach the work
platform.
8 — EQUIPMENT OPTIONS
PLATFORM ROTATOR
The optional platform rotator allows the operator to
rotate the elevated work platform 90º around a
vertical axis by actuating a rotator handle found
below the platform control panel.
To operate manual platform rotator, turn the rotator
handle in the direction of desired rotation (clockwise
or counterclockwise). Motion continues in the
desired direction until rotator handle is released or
the platform reaches a safe travel limit.
WARNING
Installation of a manual platform rotator may
reduce the rated load limit of the work platform.
Follow all manufacturer’s recommendations and
safety precautions when operating a boom lift
equipped for platform rotation.
Figure 8-3. Manual Platform Rotator
51
BIL-JAX 5533A
DRIVE AND SET
Use the following procedure to operate a boom lift
equipped with the Drive and Set option:
Set parking brake. Drive function will not operate
unless parking brake is set.
Lower jack stand and unhitch lift from tow vehicle.
If unit is equipped with a jockey wheel, remove lock
pin and swing jockey wheel into lowered position.
Reinsert lock pin to secure jockey wheel in lowered
(drive) position (See Figure 8-4).
Figure 8-4. Jockey Wheel Instruction
Raise jack stand and swing into stowed position.
Completely lower platform. Drive function will not
operate unless platform is completely lowered and
fully stowed.
Fully retract outriggers.
Press and hold the DRIVE ENABLE button. Move
joystick in the desired direction.
Machine will continue in the desired direction until
joystick or drive enable button is released.
To resume platform operation, lower outriggers and
level the lift using either the ground or platform
controls and following the instructions found in
Section 3 of this manual. Boom functions are not
available until outriggers are fully deployed and
machine is level.
DRIVE AND SET SAFETY
NEVER drive machine unless parking brake is set.
NEVER drive machine without platform fully lowered
or without operator securely inside the platform.
ALWAYS watch for personnel and obstructions in
the path of the machine. Be aware of limited visibility
and blind spots.
52
DRIVE AND SET CONTROLS
The platform control station is used to control boom motion and drive and set
functions, including outrigger deployment. To access the platform control station,
turn the key switch at the ground control station to the platform controls setting
and enter the work cage.
Figure 8-5. Drive and Set Controls
3.
Drive and Set Joystick
4.
Drive Enable Button
5.
Diagnostic Indicators
6.
Outrigger Controls
7.
Outrigger Enable Button
8.
Machine Level Indicator
9.
Platform Position LED
53
BIL-JAX 5533A
The platform control station of a Drive and Set
equipped machine includes the following controls
and indicators. Refer to Figure 8-5 for locations.
1. Drive and Set Joystick.
Move the joystick in the desired direction while
pressing and holding the DRIVE ENABLE (2) button to
drive the fully retracted boom lift.
2. Drive Enable Button.
Press and hold the DRIVE ENABLE button while using
the joystick (1) to drive the fully retracted boom lift.
Release the DRIVE ENABLE button or joystick to stop.
3. Diagnostic Indicators.
Diagnostic Indicator LEDs will light to indicate an
error in boom lift or drive function. When lit, check
the display panel on the ground control station and
the ERROR CODE DEFINITIONS chart in Section 4
of this manual.
4. Outrigger Controls.
Outriggers can be deployed from either the ground
or platform control station on drive and set
machines.
5. Outrigger Enable Button.
Press and hold the ENABLE button and the outrigger
EXTEND or RETRACT button to deploy or retract
outriggers.
6. Machine Level Indicator.
Indicator LED will light to indicate that the machine is
level and boom functions can be performed.
7. Platform Position LED.
When flashing, boom must be fully stowed before
resuming outrigger control or Drive and Set
operations.
54
REPLACEMENT DECALS
Refer to Table 8-1 and Figure 8-6 to Figure 8-7 for a
descriptions and locations of replacement decals for
optional components. Refer to Section 5 for a
comprehensive list of standard decals on the Bil-Jax
Model 5533A Telescoping Boom Lift.
All decals related to optional equipment have a
quantity of one (1) unless otherwise noted.
Table 8-1. Replacement Decals
Decal No.
Description of Decal
B06-00-0474
NOTICE: Max. Load (All
Configurations)
B06-00-0485
NOTICE: Material/Lifting
Configuration Set-Up (Material Lift
Option Only)
B06-00-0497
NOTICE: Load Capacity for Material
Lifting Hook (Material Lift Option
Only)
B06-00-0527
WARNING: Drive and Set Hazards
B06-00-0528
NOTICE: Drive and Set Instruction
B06-00-0529
NOTICE: Manual Platform Rotation
(Manual Rotation Option Only)
B06-00-0553
WARNING: Jockey Wheel
Figure 8-6. Material Lift Decal Placement
Figure 8-7. Decal Locations
55
DAILY SERVICE CHECKS
Use the following checklist to record all daily checks made to the equipment. See Section 4
for a comprehensive list of service procedures.
Copy as necessary and keep with the machine at all times.
DATE____________
Verify that all Decals are properly affixed to machine.
Verify proper operation of all functions from ground and platform control stations.
Verify proper operation of all down limit switches and outrigger position switches.
Check hydraulic oil. Add fluid as necessary.
Check tires for proper inflation.
Verify proper operation of brake lights and running lights.
56
WEEKLY SERVICE CHECKS
Use the following checklist to record all weekly checks made to the equipment. See Section 4
for a comprehensive list of service procedures.
DATE____________
Check battery electrolyte level.
Check transport hitch components for damage and proper operation.
Check electrical wiring for cuts, loose wires or damage. Repair as necessary.
Check boom lift for loose or missing hardware. Replace or repair as necessary
57
MONTHLY SERVICE CHECKS
Use the following checklist to record all monthly checks made to the equipment. See Section
4 for a comprehensive list of service procedures.
DATE____________
Clean all battery terminals.
Check Battery for loose connections or damaged wires.
Verify proper operation of manual lowering valves and hand pump.
Lubricate all compartment hinges and latches, slew ring and mating gear.
Check wheel nut torque.
Use the following space to record and date any additional service checks, maintenance or
alterations to machine. Attach any applicable certifications to this manual and keep with the
machine at all times.
Always follow manufacturer’s recommendations when repairing or maintaining the boom lift.
58
Bil-Jax, Inc.
125 Taylor Parkway
Archbold, Ohio 43502
800-537-0540
REPORTING SAFETY DEFECTS
If you believe that your vehicle has a defect that could cause a crash or could
cause injury or death, you should immediately inform the National Highway
Traffic Safety Administration (NHTSA) in addition to notifying Bil-Jax, Inc.
If the NHTSA receives similar complaints, it may open an investigation, and if it
finds that a safety defect exists in a group of vehicles, it may order a recall and
remedy campaign. However, the NHTSA cannot become involved in any
individual problems between operators, users, or lessors, and Bil-Jax, Inc.
To contact the NHTSA you may either call the Auto Safety Hotline toll-free at
800-424-9393 (366-0123 in the Washington, DC area) or write to:
NHTSA
U.S. DEPARTMENT of TRANSPORTATION
400 7th Street SW (NSA-11)
Washington, DC 20590
You can also obtain other information regarding motor vehicle
safety by calling the Hotline.
59
60
BIL-JAX SUMMIT SERIES QUICK START GUIDE
Obtain, read and obey all Safety Guidelines:
In this manual
Attached to the boom lift
Indicated by federal, state and local regulations
Position the boom lift in work area
Unhitch from the tow vehicle and disengage all boom travel latches
Turn Key Switch to ground control station for outrigger extension and leveling
Extend outriggers and level the boom
Press and hold the outrigger EXTEND and AUTO LEVEL buttons
A buzzer will sound and all LEDs will become lit on the Outrigger Control Panel
when the boom is level
Turn Key Switch to platform control station.
Enter the work platform and attach safety harness to the Fall Protection
Attachment Point
Press and hold the desired SPEED and function buttons to operate boom lift
NOTES
Distributed by:
125 Taylor Parkway
Archbold, OH 43502
Phone (419) 445-8915
(800) 537-0540
Fax
(419) 445-0367
http://www.biljax.com

Biljax 5533 Operators Manual - Cobb Rental Service, Supplying

Transcription

Similar documents

Boom extension HTLJ

Alamo Boom

Rear-Mount Boom Cutter - Bush

AT248F Articulating/Telescopic Aerial Device

MM2260 Mid-Mount Hydraulic Boom Mower

Brochure - Versatile

m726e mulcher

TRUCK-MOUNTED CONCRETE PUMPS S 58 SX / S 61 SX

RT-300-2G - Maxim Crane Works