OXY-FU EL

Transcription

OXY-FU EL

AIRCO ®
AIR PRODUCTS ®
CRAFTSMAN ®
DOCKSON ® HARRIS ®
KOIKE ®
MARQUETTE ®
MECO ®
OXWELD ®
PUROX ®
REXARC ®/REGO
SMITH®
VICTOR ®
WELDIT®
EUROPEAN
TIP NUTS
®REGISTERED TRADE MARK OF THE NAMED COMPANY. AMERICAN TORCH TIP MANUFACTURES REPLACEMENT CONSUMABLES TO FIT PRODUCTS
MANUFACTURED BY THE ABOVE NAMED COMPANIES. FIND THE PARTS YOU REQUIRE ON THE APPROPRIATE PAGES IN THIS SECTION.
YOUR SUPER SOURCE FOR CONSUMABLE REPLACEMENT PARTS
348
AIRCO®
STYLE
SIZES
TYPE & USAGE
FEATURES
FUEL: ACETYLENE
LENGTH
OXY-FUEL
112
00, 0, 1, 2, 3
Hand Cutting Use on clean surface
Flat seat design
Medium preheat-6 holes 1 piece
copper
1.75”/44.5mm
119
00, 0, 1, 2, 3, 4
Hand or machine cutting Trimmingthin sheet or for use in restricted areas
Light preheat-2 hole 1 piece
3.4” / 86.4mm
124
000, 00, 0, 1, 2, 3.
4, 5, 6, 7, 8
Hand or machine cutting for clean
plate
Light preheat 1 piece
3.4” / 86.4mm
138
000, 00, 0, 1, 2,
3, 4, 5, 6
Hand or machine cutting fine contour
plate or sheet metal
Light to medium preheat Close
circle pattern
3.4” / 86.4mm
144
000, 00, 0, 1, 2, 3, 4,
5, 6, 7, 8, 10
Hand or machine cutting-rusty,
oxidized, painted surfaces on low
carbon steel & steel castings
Medium preheat Sizes 11-14 for
rivet washing & gouging 1 piece
3.4” / 86.4mm
145
00, 0, 1, 2,
3, 4, 5, 6
Hand cutting-Gen cutting with style
2700 cutting attach 2 seat design
Light to medium preheat 1 piece
2.7” / 68.6mm
164
000, 00, 0, 1, 2,
3, 4, 5, 6, 7, 8, 9,
10, 11, 12
Hand or machine cutting General
cutting cast iron stainless steelextensive preheat plate rust scale
painted surfaces
Heavy preheat 1 piece
3.4” / 86.4mm
183
4, 6, 8, 10, 12
For grooving, gouging, flame
machining & removing imperfect
welds
Medium preheat Tip bent 20º
1 piece
4.4” / 111.8mm
195
1, 2, 3, 4, 5
Hand or machine cutting 45º machine
cutting bevel-hand cutting rivet
heads/bulkheads
Medium preheat Tip bent 45º
1 piece
3.8” . 86.4mm
196
8, 10, 12, 14
Rivet washing
Medium preheat 1 piece
3.4” / 86.4mm
STYLE
SIZES
TYPE & USAGE
FEATURES
FUEL: PROPANE/NTURAL GAS
LENGTH
219
00, 0, 1, 2, 3,
4, 5, 6, 7, 8
Hand or machine cutting
General purpose cutting
Light Preheat 2 piece
3.4” / 86.4mm
229
00, 1, 2, 3, 4, 5
6, 7, 8, 10, 12, 14
Light 2 piece
3.4” / 86.4mm
261
00, 0, 1, 2, 3, 4, 5, 6,
7, 8, 9, 10, 11, 12
Hand cutting material in excess
of 8’ -Machine cutting up to 14”
for cutting clean plate
Heavy preheat 2 piece
Exceptional flame stability
3.4” / 86.4mm
263
00, 0, 1, 2, 3,
4, 5, 6, 7, 8, 9, 10
straight bore cutting
for material up to 8”
Medium preheat - 22º V splines for
max heat transfer fast piercing/
starting 2 piece
3.4” / 86.4mm
275
00, 0, 1, 2, 3,
4, 5, 6, 7, 8, 9, 10
General purpose for thick plate
straight bore cutting
Fast preheat
22º V splines sizes 00-5
36º V splines 6-8
3.3” / 83.8mm
349
AIRCO® (cont.)
STYLE
SIZES
TYPE & USAGE
FEATURES
FUEL: PROPANE/NATURAL GAS
LENGTH
287
6, 8, 10, 12
Grooving & gouging
For removing imperfect welds
Heavy preheat tip bent 22
Low velocity oxygen stream
5.3”/134.6mm
375
00, 0, 1, 2, 3,
4, 5, 6, 7, 8
Machine cutting-high speed
Diverged orifice allows more
cutting oxygen pressure
Heavy fast preheat
2-piece - 220 V splines
Designed for high speed cutting
3.3”/83.8mm
STYLE
SIZES
0
TYPE & USAGE
FEATURES
FUEL: MAPP/PROPYLENE
LENGTH
00, 0, 1, 2, 3,
4, 5, 6, 7, 8
General purpose
Medium preheat Fine splines and
flutes 2-piece
3.3”/83.8mm
345
00, 0, 1, 2, 3,
4, 5, 6, 7, 8
Machine Cutting - High speed
General purpose
(same as 245 except H.S.)
Heavy preheat 2-piece Designed for high speed cutting
3.3”/83.8mm
A-SP
72,68,60,56,52
49,44,42,38,31,
28, 19
Hand cutting
1-piece
8 preheat
3.4”/86.4mm
A-FS
72,68,60,56,52
49,44,42,38,31,
28, 19
Hand & machine cutting
Medium to heavy Even preheat
pattern 2-piece-fine spline
3.4”/86.4mm
A-FH
72,68,60,56,52
49,44,42,38,31,
28,19
General purpose Use with
high pressue cutting oxygen
Heavy preheat Even preheat pattern
2-piece designed for high speed
cutting
3.4”/86.4mm
A-G1
2,4 - 8 hole
6,8 - 10 hole
#10, #12
Grooving and gouging
Deseaming and removing
imperfect welds
Medium to Heavy Tip bent
300 for easu use 1-piece
Speed-medium
4.8”/121.9mm
Heating - for use in
cutting torches and
attachments.
2-piece
3.4”/86.4mm
A-HT
AIRCO® - MULTI-USE ADAPTERS
TORCH
ADAPTER No.
ADAPTER NUT
PART
LENGTH
REGULAR
Replaces 124, 144, 164, 261, 275, 361
A90
Std.Airco nut
831-2559
2.25”/57.2mm
SMALL
Replaces 145, 155
A-45-A**
A45N
2.0”/50.8mm
NOTES: **REQUIRES ADAPTER NUT SHOWN
SEE PAGE 23 FOR AVAILABLE TIPS
OXY-FUEL
245
350
AIR PRODUCTS® / CRAFTSMAN®
AIR PRODUCTS®(KG)
STYLE
SIZES
TYPE & USAGE
FEATURES
FUEL: ACETYLENE
LENGTH
111
00, 0, 1. 2, 3, 4, 5
General purpose
1-piece-threaded
Light preheat
3.8”/96.5mm
121
00, 0, 1, 2, 3,
4, 5, 6, 7, 8
General purpose
Medium preheat
1-piece
3.8”/96.5mm
159
00, 0, 1, 2, 3, 4,
5, 6, 7, 8, 9, 10
General purpose
1-piece - Conical Seat
Light preheat
3.4”/86.4mm
STYLE
231
SIZES
00, 0, 1, 2, 3,
4, 5, 6, 7, 8.9
TYPE & USAGE
FEATURES
General purpose
Heavy preheat 2-piece
LENGTH
3.4”/86.4mm
AIR PRODUCTS®(KG) - MULTI-USE ADAPTERS
TORCH
ADAPTER No.
Replaces 121, M6, 201, KGLG
ADAPTER NUT
KG
PART
Std. KG Nut
No Special nut required
LENGTH
2.9”/73.7
OXY-FUEL
CRAFTSMAN®
STYLE
B
SIZES
TYPE & USAGE
FEATURES
68, 62, 60, 56, 52, 49
Hand cutting General or scrap cutting
FUEL: ACETYLENE
Medium preheat
1-piece
LENGTH
3.0”/76.2
(NOTE:Tips are for old style tip mix) For new style see Harris
STYLE
BL
SIZES
68,62,60,56,52,49
TYPE & USAGE
FEATURES
General purpose
LIGHT preheat
2-piece
LENGTH
3.0”/76.2mm
CRAFTSMAN ® - MULTI-USE ADAPTERS
TORCH
Replaces B, BL
ADAPTER No.
CRF-A**
ADAPTER NUT
CRF-N
PART
LENGTH
2.0”/50.8mm
351
DOCKSON® / HARRIS®
STYLE
SIZES
C-6
00, 0, 1, 2, 3,
4, 5, 6, 7, 8
STYLE
SIZES
CG
00, 0, 1, 2, 3,
4, 5, 6, 7, 8
TYPE & USAGE
FEATURES
Hand cutting & cutting attachments
General purpose
Medium preheat
1-piece
TYPE & USAGE
Hand cutting
General purpose
FUEL: ACETYLENE
FEATURES
LENGTH
2.7”/68.6mm
Medium preheat
2-piece
LENGTH
2.8”/71.1mm
DOCKSON®- MULTI-USE ADAPTERS
TORCH
Replaces C-6, CG
ADAPTER No.
DOC-A**
ADAPTER NUT
PART
DOC-N
LENGTH
2.0”/50.8mm
STYLE
SIZES
TYPE & USAGE
FEATURES
FUEL: ACETYLENE
LENGTH
3690
00, 0, 1, 2
Mini cutting tip
Can be used for welding & brazing
Light preheat 1-piece
1.5”/38.1mm
6290
000, 00, 0, 1, 2,
3, 4, 5, 6
General purpose
Medium preheat 1-piece
2.5”/63.5mm
6290S
000, 00, 0, 1, 2,
3, 4, 5, 6
General purpose, scrape heavily
rusted, Ideal for beveling
Cutting plate 1/16 to 12” thick
2.4”/61.0mm
6290D
1,2,3
Hand cutting
Drag type for cutting & trimming
light plate
Light peheat 1-piece
2.5”/63.5mm
6290G
1,2,3
Gouging, grooving and removing
imperfect welds
Medium preheat 1-piece-bent
2.3”/58.4mm
7490A
00, 0, 1, 2, 3, 4,
5, 6, 7,8
General purpose
3.9”/99.1mm
OXY-FUEL
HARRIS®
352
HARRIS®
HARRIS®
STYLE
SIZES
TYPE & USAGE
FEATURES
LENGTH
OXY-FUEL
3690P
00, 0, 1, 2
Mini cutting tip 2-piece
Light preheat
1.3”/33.0mm
6290 N
000, 00, 0, 1,
2, 3, 4, 5, 6
General purpose
Medium preheat 2-piece-(heavy wall)
2.5”/63.5mm
6290 NH
4, 5, 6, 7, 8
Machine cutting For heavy cutting
of plate
2.5”/63.5mm
6290 NX
000, 00, 0, 1,
2, 3, 4, 5, 6
General purpose-straight line
clean surface cutting-3/16-12”
2.5”/63.5mm
6290 NXP
000, 00, 0, 1,
2, 3, 4, 5, 6
General purpose-straight line
clean surface cutting-3/16-12”
2.5”/63.5mm
6290 NFF
00, 0, 1, 2, 3,
4, 5, 6, 7
General purpose-scrape, heavily
rusted, scaled or painted metal
5/8 to 12”. Ideal for beveling
Medium preheat 2-piece -chrome
plated ext.
2.5”/63.5mm
6290 NFW
4, 5, 8
Hand cutting Gouging,rivet washing, removing weld metal. Metal
preparation and beveling
Medium to heavy preheat 2-piece
2.5”/63.5mm
6290 HRW
4, 5, 8
Rivet washing
2.5”/63.5mm
6290 VVC
5/0, 4/0, 000, 00, 0,
01/2, 1, 11/2, 2,
21/2, 3, 4, 5, 6
Machine cutting High speed oxygen
flow-narrow cutting jet and kerf
2.5”/63.5mm
6290 GG
1, 2, 3
Gouging 1-piece-bent
Medium prehea
4.0”/101.6mm
2290 HH
1, 2, 3, 4, 5,
Hand heating
High heat
3.25”/82.6mm
7490 BTU
00, 0, 1, 2, 3, 4, 5,
6, 7, 8
General purpose
(rugged/durable)
3.9”/99.1mm
6290 H-SP
72,68,60,56,
52,49,44,42,
38,31,28,19
General purpose metal cutting
3/16” to 12”
2.4”/61.0mm
353
HARRIS® (cont.)
STYLE
SIZES
TYPE & USAGE
FEATURES
FUEL: ACETYLENE
LENGTH
6290 H-FS
72,68,60,56,
52,49,44,42,
38,31,28,19
Cutting
General purpose
Metal 3/16” to 12”
Medium to heavy
2-piece Fine spline flutes
2.4”/61.0mm
6290 VVCM
5/0, 4/0, 000, 00, 0,
01/2, 1, 11/2, 2, 21/2,
3, 4, 5
Machine cutting
2.4”/61.0mm
6290 VVCP
5/0, 4/0, 000, 00, 0,
01/2, 1, 11/2, 2, 21/2,
3, 4, 5, 6
Machine cutting
Precision high speed mach. cutting
high speed oxygen flow-narrow
cutting jet-low fuel consumption
Narrow kerf
Heavy 2-piece
2.5”/63.5mm
2290 MPHD
1, 2, 3, 4, 5
Hand heating
Heavy heating for MAPP gas
2.0”/50.8mm
NOTE: 2490 series -same as above
HARRIS® - MULTI-USE ADAPTERS
TORCH
ADAPTER No.
ADAPTER NUT
PART
LENGTH
H-62-A**
H-62-N
1.4”/35.6mm
Replaces 7490A, 7490BTU
2.7”/68.6mm
C5
Std. Harris Nut
2.7”/68.6mm
Replaces 2890, 2890P
H-28
Std. Harris Nut
1.8”/45.7mm
OXY-FUEL
Replaces 6290, NX, NFF, VVC
1.4”/35.6mm
354
KOIKE®
STYLE
SIZES
TYPE & USAGE
FEATURES
FUEL: ACETYLENE
LENGTH
102
00, 0, 1, 2, 3,
4, 5, 6, 7, 8
General cutting
Medium preheat
1-piece
3.5”/88.9mm
102 D5
00, 0, 1, 2, 3,
4, 5, 6, 7, 8
General cutting
High speed cutting
Medium preheat
1-piece
3.5”/88.9mm
102 D7
00, 0, 1, 2, 3,
4, 5, 6, 7, 8
Machine cutting
Stainless steel insert
High speed cutting
Medium preheat
1-piece
3.5”/88.9mm
STYLE
SIZES
TYPE & USAGE
FEATURES
LENGTH
106
00, 0, 1, 2, 3,
4, 5, 6, 7, 8
General cutting
Medium preheat
2-piece
3.5”/88.9mm
106 O7
00, 0, 1, 2, 3,
4, 5, 6, 7, 8
Machine cutting
High speed cutting
Medium preheat
2-piece
w/O-Ring
3.5”/88.9mm
106 D7
00, 0, 1, 2, 3,
4, 5, 6, 7, 8
Machine cutting
High speed cutting
Medium preheat
2-piece
3.5”/88.9mm
107
00, 0, 1, 2, 3,
4, 5, 6, 7, 8
General cutting
Medium preheat
2-piece
3.5”/88.9mm
107 D7
00, 0, 1, 2, 3,
4, 5, 6, 7, 8
Machine cutting
High speed cutting
Medium preheat
2-piece
3.5”/88.9mm
OXY-FUEL
STYLE
SIZES
TYPE & USAGE
FEATURES
LENGTH
103
00, 0, 1, 2, 3,
4, 5, 6, 7, 8
General cutting
Medium preheat
2-piece
3.5”/88.9mm
103 D7
00, 0, 1, 2, 3,
4, 5, 6, 7, 8
Machine cutting
High speed cutting
Medium preheat
2-piece
3.5”/88.9mm
KOIKE® - MULTI-USE ADAPTERS
TORCH
Replaces 102, 102 D7, 103, 103 D7
106, 106 D7, 107, 107 D7
ADAPTER No.
KOI-A
ADAPTER NUT
PART
Std. Koike nut
KOI-N
LENGTH
1.9”/48.3mm
** REQUIRES ADAPTER NUT SHOWN
STYLE
GW-6
STYLE
GWP
SIZES
00, 0, 1, 2, 3, 4, 5, 6
SIZES
00, 0, 1, 2, 3, 4, 5, 6
TYPE & USAGE
General Cutting
TYPE & USAGE
General Cutting
FEATURES
FUEL: ACETYLENE
Light to medium preheat 1-piece
FEATURES
LENGTH
3.5”/88.9mm
LENGTH
3.5”/88.9mm
355
MARQUETTE®/MECO®
MARQUETTE - MULTI USE ADAPTERS
TORCH
Replaces GW-6, GWP
ADAPTER No.
MKT
ADAPTER NUT
PART
#27159
Std. Marquette
Nut
LENGTH
1.9”/48.3mm.
NOTES: SEE PAGE 23 FOR AVAILABLE TIPS
MECO®
STYLE
LA-6
SIZES
00, 0, 1. 2, 3, 4, 5, 6
STYLE
SIZES
TYPE & USAGE
Hand cutting
FEATURES
TYPE & USAGE
FEATURES
LM
00, 0, 1. 2, 3, 4, 5, 6
Hand General purpose
Medium preheat 2-piece milled tip
LB
00, 0, 1. 2, 3, 4, 5, 6
Hand General purpose
Medium preheat 1-piece with recess
STYLE
SIZES
FUEL: ACETYLENE
TYPE & USAGE
FEATURES
LENGTH
2.8”/71mm
LENGTH
2.9”/73.7mm
2.8”/71mm
LENGTH
72,68,60,56,
52,49,44,42,38,35,30,
General purpose
2.8”/71.1mm
M-FS
(LMM)
72,68,60,56,
52,49,44,42, 38
General purpose
Medium to heavy 2-piece
2.8”/71.1mm
MECO® - MULTI-USE ADAPTERS
TORCH
Replaces LA-6, LM
ADAPTER No.
MCM
ADAPTER NUT
1641
Use std.
Meco tip nu
PART
LENGTH
1.9”/48.3mm
OXY-FUEL
M-SP
(LMG)
356
OXWELD®
STYLE
SIZES
TYPE & USAGE
FEATURES
FUEL: ACETYLENE
LENGTH
1501
2, 3, 4, 6, 8,10, 12
Hand & straight line machine cutting. Use on clean surfaces General
purpose
Light to medium preheat
1-piece-swaged copper
3.4”/86.4mm
1502
2, 3, 4, 6, 8,10, 12
General purpose- poor or dirty
surfaces.Mach.cut irregular shapes
Medium preheat
1-piece
2.8”71.1mm
1505
20, 24, 28
Deseaming-scarfing
Light preheat
2-piece
1511
13, 19, 25
Gouging-removing defective welds
Grooving steel plate or castings
Medium preheat
1-piece-angled
3.4”/86.4mm
1514
28,31,47,52,60,
80,100,120,140
Machine cutting cutting bars,billet &
forging blanks Low or medium pressure Acetylene
Heavy preheat
1-piece
2.8”/71.1mm
1563
1/2,3/4,1,1-1/2,2
2-1/2,4,6,10,14
Machine cutting High speed cutting
Can bevel clean plate up to 450
Heavy preheat
1-piece-Fuel saving features
2.8”/71.1mm
1565
1/8, 1/4, 1/2, 3/4
1, 2, 3, 4
General purpose Bevel plate up to 450
Medium preheat
1-piece-low fuel use
2.8”/71.1mm
STYLE
OXY-FUEL
1515
1534
SIZES
TYPE & USAGE
FEATURES
Available while stocks last
LENGTH
3, 4, 6, 8, 10, 12, 14,
16, 18, 20
General purpose Use for gouging
Medium preheat 1-piece-swaged
copper With recessed front
3.4”/86.4mm
2, 3, 4, 6, 8, 10, 12,
14, 16, 20, 22
General purpose
3.3”/83.8mm
Complete
External Sleeve Part #
NG/ Propane
FG-2/MPP
1534-2 thru 4-Complete....................14Z38........................114Z07/998560
1534-6 thru 8-Complete....................14Z39........................114Z08/998561
1534-10 thru 12-Complete................14Z77.......................................14Z96
1534-14 thru 22-Complete................14Z69...........................................N/A
*Gas must be specificed
STYLE
1535
SIZES
28,31,47,52,60,
80,100,120,140
Complete
TYPE & USAGE
High speed cutting
NG/ Propane
FG-2/MPP
1535-31 thru 52-Complete.................14Z38.......................114Z07/998560
1535-60 thru 80-Complete.................14Z39.......................114Z08/998561
1535-100-Complete ...........................14Z77.....................................14Z69
1535-120 thru 140-Complete
FEATURES
LENGTH
3.4”/86.4mm
357
OXWELD® (cont.)
STYLE
1508
SIZES
24, 28
STYLE
TYPE & USAGE
Hand use For scarfing-deseaming
SIZES
FEATURES
Medium preheat 2-piecefurnished with wearring & nut
TYPE & USAGE
LENGTH
3.8”/96.5mm
FEATURES
FUEL: ACETYLENE
LENGTH
1515
3, 4, 6, 8, 10, 12, 14,
16, 18, 20
General purpose
Use for gouging
Medium preheat
1-piece-swaged copper
With recessed front
3.4”/86.4mm
1534
2, 3, 4, 6, 8, 10, 12,
14, 16, 20, 22
General purpose
3.3”/83.8mm
Complete
NG/ Propane FG-2/MPP
1534-2 thru 4-Complete ....................14Z38.......................114Z07/998560
1534-6 thru 8-Complete.....................14Z39.......................114Z08/998561
1534-10 thru 12-Complete.................14Z77......................................14Z96
1534-14 thru 22-Complete.................14Z69..........................................N/A
STYLE
1535
SIZES
28,31,47,52,60,
80,100,120,140
Complete
TYPE & USAGE
High speed cutting
FEATURES
Medium preheat
2-piece
LENGTH
3.4”/86.4mm
FG-2/MPP
1535-31 thru 52-Complete...................................14Z38.....................114Z07/998560
1535-60 thru 80-Complete ..................................14Z39.....................114Z08/998561
1535-100-Complete ............................................14Z77....................................14Z69
1535-120 thru 140-Complete
STYLE
SIZES
TYPE & USAGE
FEATURES
LENGTH
O-SP (1564)
72,68,60,56,
52,49,44,42,
38,31,28,19
General purpose
Medium preheat
1-piece
3.4”/86.4mm
O-FS
72,68,60,56,
52,49,44,42,
38,31,28,19
General purpose
Medium to heavy
2-piece Fine spline
3.3”/83.8mm
O-GW
86, 113, 147, 191, 254
Hand use For gouging & washing
3.7”/94.0mm
OXWELD ® /L-TEC® - MULTI-USE ADAPTERS
TORCH
Replaces
1502, 1534,
1535, 1566, 1567
ADAPTER No.
032
ADAPTER NUT
33A56 Std. Oxweld nut
PART
LENGTH
1.9”/48.3mm.
OXY-FUEL
NG/ Propane YOUR SUPER SOURCE FOR CONSUMABLE REPLACEMENT PARTS
358
PUROX®
STYLE
SIZES
TYPE & USAGE
FEATURES
FUEL: ACETYLENE
LENGTH
4201
2, 3, 4, 5, 7, 9, 11, 13
General purpose
Light preheat
1-piece
2.9”/73.7mm
4202
2, 3, 4, 5, 7, 9, 11, 13
Hand cutting attachment
General purpose
Medium preheat
1-piece
2.9”/73.7mm
STYLE
SIZES
TYPE & USAGE
FEATURES
LENGTH
4203
3, 4, 5, 6, 7, 8, 9, 10, 11,
12,13
General purpose
Medium preheat
1-piece- also avail. in 2
pieces for all sizes
2.9”/73.7mm
4213-14
2, 3, 4, 5, 7, 9, 10, 11, 12, 13
General purpose
Medium preheat
2-piece-Cylindrical oxygen
cutting bore
2.8”/71.1mm
STYLE
SIZES
TYPE & USAGE
FEATURES
LENGTH
P-SP
72, 68, 60, 56, 52,49, 44, 42,
38, 31, 28,19
General purpose
2.9”/73.7mm
P-FS
72, 68, 60, 56, 52, 49, 44,
42, 38
General purpose
2.8”/71.1mm
P-FSP
72, 68, 60, 56, 52, 49, 44,
42, 38
General purpose
Medium to heavy 2 piece
2.8”/71.1mm
OXY-FUEL
PUROX® /L-TEC ® - MULTI-USE ADAPTERS
TORCH
Replaces 4202, 4203, 4213, 4214
ADAPTER No.
PE-A**
ADAPTER NUT
PE-N
PART
LENGTH
1.7”/43.2mm
359
REXARC® (REGO®)
STYLE
SIZES
TYPE & USAGE
FEATURES
FUEL: ACETYLENE
LENGTH
KX6
68 62,56,53, 51,46,42,35,
30,25,18
General purpose
Medium preheat 1-piece-(6 holes)
KX66
68 62,56,53, 51,46,42,35,
30,25,18
General purpose
Medium to heavy 1-piece-mix type
(6 hole) Size 68 has 4 holes
150A
65,62, 56,53
General purpose
Light preheat (3 hole & 4 hole
1-piece
1.6”/40.7mm
150P
65,62, 56,53
General purpose
1.9”/48.3mm
STYLE
SIZES
TYPE & USAGE
FEATURES
3.0”/76.2mm
LENGTH
KX-105
68 62,56,53, 51,46,42,35,
30,25,18
General purpose
Medium preheat
2-piece-cupped tip
3.3”/83.8mm
KX-205
68 62,56,53, 51,46,42,35,
30,25,18
High speed cutting
Medium preheat
2-piece
2.7”/68.6mm
SIZES
TYPE & USAGE
R-SP
STYLE
72,68,60,56,52,49,44,42,
38,31,28,19
General purpose
Medium preheat
1-piece KX type
FEATURES
3.0”/76.2mm
LENGTH
R-FS (KXM-105)
72,68,60,56,52,49,44,42,
38,31,28,19
General purpose
Medium to heavy
2-piece
3.3”/83.8mm
TORCH
Replaces KX-6, KX-105
ADAPTER No.
RKX
ADAPTER NUT
Std. Rego nut
PART
LENGTH
OXY-FUEL
REXARC® (REGO®) MULTI-USE ADAPTERS
360
SMITH®
STYLE
SIZES
TYPE & USAGE
FEATURES
FUEL: ACETYLENE
LENGTH
lc6
000, 00, 0, 2
Hand & machine
Medium
3.0”/76.2mm
mc 12
00, 0, 1, 2 3, 4, 5, 6, 7
Hand cutting General purpose
cutting 3/16” to 6” plate
2.8”/71.1mm
sc 10
00, 0, 1, 2 3, 4, 5, 6, 7
General purpose-1/4” to 4” plate
3.6”/91.4mm
sc 12
000, 00, 0, 2, 3, 4, 5, 6, 7 General purpose
3.6”/91.4mm
sc 13
1, 3, 5
Heavy preheat
1-piece
3.6”/91.4mm
STYLE
Hand Use Gouging, Cutting V
grooves Remove old welds
SIZES
TYPE & USAGE
FEATURES
LENGTH
OXY-FUEL
SC 40
00, 0, 1, 2, 3,4, 5, 6, 7
General purpose
Medium preheat
2-piece
3.6”/91.4mm
SC 46
00, 0, 1, 2, 3,4, 5, 6, 7
Heavy cutting tip
Cutting scrap metal
Medium-heavy preheat 1-piece
Recessed front
3.6”/91.4mm
SC 50
00, 0, 1, 2, 3,4, 5, 6, 7
8, 9, 10
Heavy cutting tip
for steel up to 20”
3.6”/91.4mm
SC 21
00, 0, 1, 2, 3,4, 5, 6
Machine cutting
High speed
2.9”/73.7mm
LC 46
00, 0, 1, 2, 3,4, 5, 6,7
General purpose
Medium preheat
3.0”/76.2mm
STYLE
S-FS (SC 90)
SIZES
72,68,60,56 52,49,44,42
38, 31
TYPE & USAGE
General purpose
FEATURES
Fine spline
LENGTH
3.6”/91.4mm
SMITH® - MULTI-USE ADAPTERS
TORCH
ADAPTER No.
ADAPTER NUT
PART
LENGTH
Replaces SC12, SC50
SC
SCG 900-41A Std. nut
2.2”/55.9mm
Replaces LC-6 -00,0,1,2,3,5,6
SLT
G771-A Std. nut
2.5”/63.5mm
361
VICTOR®
STYLE
SIZES
TYPE & USAGE
FEATURES
FUEL: ACETYLENE
LENGTH
1-100
00, 0, 1, 2, 3, 4, 5, 6,
7, 8
Hand & machine cutting Clean plate
& general purpose
2.5”/63.5mm
1-101
000, 00, 0,1, 2, 3, 4,
5, 6,7,8
General purpose
2.5”/63.5mm
1-118
0, 2, 4, 6, 8, 10, 12
Hand use Gouging,deseaming, scarfing, weld preparation, rivet washing
Medium preheat 1-piece-350
angle tip
2.7”/68.6mm
3-101
000, 00, 0, 1, 2, 3, 4,
5, 6
General purpose Deseaming, gouging, removing defective welds &
Rivet washing
1.9”/48.3mm
3-118
0, 2, 4
Hand use
Medium preheat 1-piece-350
angle tip
2.1”/53.3mm
5-101
000, 00, 0, 1, 2, 3, 4,
5, 6
General purpose
1.7”/43.2mm
STYLE
SIZES
TYPE & USAGE
FEATURES
LENGTH
000, 00, 0, 1, 2, 3,4, 5,
6, 7, 8, 10, 12
Scrape cutting General purpose
2.5”/63.5mm
2-210N
(GPN)
000, 00, 0,1,2, 3,4, 5, 6,
7, 8, 10, 12
General purpose
2.5”/63.5mm
1-200
000, 00, 0, 1, 2, 3, 4, 5,
6, 7, 8
General purpose
2.5”/63.5mm
(GPN)
000, 00, 0, 1, 2, 3,
4, 5, 6, 7, 8, 10, 12
2.5”/63.5mm
3-200
000, 00, 0, 1, 2, 3, 4
General purpose
1.9”/48.3mm
(3-GPN)
000, 00, 0, 1, 2, 3, 4,
5, 6
General purpose
1.9”/48.3mm
3-MTHN
000, 00, 0, 1, 2, 3, 4, 5
Machine cutting High Speed
for cutting up to 10” plate
2.1”/53.3mm
MTHN
00, 0, 1, 2, 3, 4, 5, 6, 7
Machine cutting high speed
2.5”/63.5mm
HPN
1, 2, 3, 4, 5, 7, 8, 9, 10,
11, 12
Hand use For scrap, bevel and heavy
peheat uses
2.5”/63.5mm
SIZES
TYPE & USAGE
STYLE
FEATURES
2V-SP
72, 68, 60, 56, 52, 49,
44, 42, 38, 31, 28
General purpose
(1-303M)
000, 0, 1, 2, 3, 4, 5,
6, 7, 8
General purpose
2V-SF
72, 68,60,56,52,49,44,4
2,38,31,
General purpose
LENGTH
2.5”/63.5mm
2.4”/61.0mm
OXY-FUEL
2-210N
362
VICTOR®
STYLE
SIZES
TYPE & USAGE
FEATURES
FUEL: ACETYLENE
LENGTH
OXY-FUEL
GPM
000, 0, 1, 2, 3, 4, 5, 6,
8, 10, 12
General purposMedium preheat
2-piece
2.4”/61.0mm
2V-G1
(1-318M)
(1-318MP)
0, 1, 2, 4, 6, 8, 10, 12
Hand use Gouging, deseaming, rivet
cutting, removing defective welds
Medium preheat
1-piece-350 angle tip
2.3”/58.4mm
3V-SP
(3-303M)
72,68,60,56,
52,49,44,42
38,31,28,19
General purpose
1.9”/48.3mm
3V-FS
(3-GPM)
72,68,60,56,
52,49,44,42
38,31,28,19
General purpose
2.1”/48.3mm
3V-G1
(3-318M)
2, 4 - 8 hole
6, 8 - 10 hole
Hand use Gouging, deseaming, rivet
cutting, removing defective metal
/welds
Medium preheat 1-piece 1
piece-Chrome plated
2.2”/55.9mm
5V-SP
72,68,60,56, 52,49,44
General purpose
Medium 1-piece
MTHM
00, 0, 1, 2, 3, 4, 5,
6, 7, 8
Machine cutting High Speed up to 10”
2.5”/63.5mm
3-MTHP
3-MTHM
000, 00, 0, 1, 2, 3, 4, 5
2.1”/53.3mm
MTHP
MTM
00, 0, 1, 2, 5, 6 7
2.5”/63.5mm
HPP
HPM
1, 2, 3, 4, 5, 7, 8, 9,
10, 11, 12
Hand use Heavy shell - for scrap,
bevel heavy preheat requirements
2.4”/61.0mm
Available while stocks last
VICTOR®- MULTI-USE ADAPTERS
TORCH
ADAPTER No.
ADAPTER NUT
PART
LENGTH
Replaces 1-101, GPN MTHN
V40
0309-0018 Std. nut
1.8”/45.7mm
Replaces 3-101, 3GPN
C-14-A**
C-14- N
1.8”/45.7mm
W-SP
W-37-A
W-37-N
2.95”/75mm
WELDIT®
STYLE
SIZES
TYPE & USAGE
FEATURES
LENGTH
S
General Purpose
Medium Preheat Acetylene
3.1”/78.8mm
W-SP
General Purpose MAPP
Medium Preheat 1-piece
3.1”/78.8mm
363
EUROPEAN
AGA®
STYLE
SIZES
TYPE & USAGE
FEATURES
FUEL: ACETYLENE
LENGTH
211
1, 2, 3, 4, 5
General purpose
44mm
302
2, 3, 4, 5, 6, 7, 8
General purpose
88mm
STYLE
SIZES
211 Tetrene
TYPE & USAGE
General purpose
FEATURES
Light preheat 2- piece
LENGTH
44mm
BOC®
STYLE
SIZES
TYPE & USAGE
FEATURES
FUEL: ACETYLENE
LENGTH
ANM
0.8, 1.2, 1.6, 2.0,
2.4, 2.8, 3.2 -(all mm)
General purpose
76mm
ANME
0.8, 1.2, 1.6, 2.0,
2.4, 2.8, 3.2 -(all mm)
Hand cutting General purpose
Large body for improved heat
dissipation
Speed-standard
88mm
AGNM
13, 19, 25
Hand gouging For fast accurate
removal of weld defects and weld
preparation
Speed-fast
100mm
SIZES
ADAPTER No.
ADAPTER NUT
LENGTH
PNM
0.8, 1.2, 1.6, 2.0, 2.4,
2.8, 3.2 -(all mm)
Hand cutting
General purpose
Medium preheat
2-pc.-9 spline only-3-300mm
18 spline-3-100mm
Speed-standard
76mm
PNME
0.8, 1.2, 1.6, 2.0,
2.4, 2.8, 3.2 -(all mm)
Hand cutting
General purpose
Available with zero back-pressure
Medium preheat
2-pc.-9 spline only-3-300mm
18 spline-3-100mm
Speed-standard
88mm
SIZES
TYPE & USAGE
CIG®
STYLE
FEATURES
FUEL: ACETYLENE
LENGTH
41
8, 10, 12, 15, 20,
24, 32
General purpose
ILLU TION NOT AVAILABLE
70mm
41HS
6, 8, 12, 15, 20, 24
High speed
Medium Preheat 1-piece
ILLU TION NOT AVAILABLE
70mm
41 GS (ref. 1511) 32
Gouging-straight
Straight design
70mm
41 GB
Gouging-bent
Bent design
95mm
32, 48, 64
OXY-FUEL
STYLE
364
European (Continue)
CIG® (Continue)
STYLE
SIZES
TYPE & USAGE
FEATURES
FUEL: ACETYLENE
LENGTH
44
6, 8, 10,12, 15, 20,
24, 32
70mm
44HS
6, 8, 20, 12, 15,
20, 24
High speed cutting
70mm
44GB
32, 48, 64
Gouging-bent
95mm
44GS
32
Gouging-straigh
70mm
ESAB®
STYLE
OXY-FUEL
FUEL: ACETYLENE
LENGTH
A8 3.700.008
8
SIZES
Marking nozzle
TYPE & USAGE
1 piece
FEATURES
ILLUSTRATION NOT AVAILABLE
87mm
IAA 250 K
3mm-250mm
Cutting - standard
2- piece
(Specify part # when ordering)
IPA 250K
3mm-250mm
Cutting - standard
2- piece
IPA 250K
3mm-250mm
Cutting - standard
2- piece - NG only
Converging slots
IPB 300 L
3mm-300mm
Cutting- high speed
2- piece
GPB 300 L
GYB 300 L
5mm-300mm
Spare parts
IPD 300 L
3mm-300mm
Cutting - Super high speed
2- piece
GEGA®
STYLE
SDS
SIZES
26F, 33F, 36F
TYPE & USAGE
Machine cutting continuous casting
FEATURES
LENGTH
1.0”/25.4mm
MESSER®
STYLE
SIZES
TYPE & USAGE
FEATURES
FUEL: ACETYLENE
LENGTH
A-RS
3-10, 10-25, 25-40,
40-60, 60-100, 100200, 200-300
85mm
A-CID
3-5, 5-10, 1--25,
25-40, 40-60, 60-80,
80-100, 100-200,
200-300
85mm
365
European (Continue)
MESSER® (Continued)
STYLE
SIZES
TYPE & USAGE
FEATURES
FUEL: ACETYLENE
LENGTH
PL-RC
3-10, 10-25, 25-40, 40-60,
60-100, 100-200, 200-300
85mm
1215-A
3-5, 6-10, 10-25, 25-40,
40-60, 60-100, 100-150,
150-230, 230-300
High Speed flame cutting nozzle
2-piece
85mm
STYLE
SIZES
TYPE & USAGE
FEATURES
1230-PMY
3-10, 7-15, 15-25, 25,40,
40-60, 60-100
High Speed cutting nozzlw
2-piece
1270-PY
3-5, 6-10, 10-25, 25-50,
50-80, 80-100
Heavy duty flame cutting nozzle
2-piece
1280-PMY
100-200, 200-250, 250-300
High speed cutting nozzle
2-piece
PM-RPM
3-6, 6-15, 15-25, 25-40,
40-60, 60-100, 100-200,
200-250. 250-300
FUEL: MAPP/PRYLENE
LENGTH
60mm
39mm
STYLE
G1-AD
SIZES
7/10, 10/10, 16/10,
20/10, 25/10, 30/10
TYPE & USAGE
Hand cutting
FEATURES
FUEL: ACETYLENE
High preheat 1-piece
LENGTH
3.4”/ 86.4mm
TANAKA®
STYLE
SIZES
TYPE & USAGE
FEATURES
LENGTH
3040g
General purpose
2.9”/73.7mm
3051
General purpose
2.9”/73.7mm
STYLE
MARKING
NOZZLE
STYLE
SIZES
P-8, P-10v
SIZES
TYPE & USAGE
Marking
FEATURES
2-piece
TYPE & USAGE
FEATURES
FUEL: LIQUID GAS
LENGTH
60mm
FUEL: MAPP/PRYLENE
LENGTH
MULTI-USE ADAPTERS FOR EUROPEAN TIPS
TORCH
Cigweld®
Messer®
Saf®
PART
41-44, A-RS, PL-RC, Gricut
G1-AD
ILLUSTRATIONS NOT AVAILABLE
OXY-FUEL
SAF®
366
TIP NUTS
TORCH TYPE
TORCH MODEL
PART NUMBER
OXY-FUEL
AIRCO
3000 & 9000
831-2559 (144TIP)
AIRCO
2490 & 2475
831-2466
DOCKSON
C
C-1 USE PE-N
HARRIS
62 (OLD) FINE
6259A
HARRIS
62 (NEW) COURSE
6259B
HARRIS
H-76
7459C5
KG
SCREW IN
229-V-360-000
MECO
L
1641
OXWELD
C31 & C32
33A56 - 33A34 FOR 1427 NUT
PART
367
TIP NUTS
TORCH TYPE
TORCH MODEL
PART NUMBER
E
902
REGO
KX OLD STYLE
3978-21
REGO
KX NEW STYLE
4278-21
SMITH
LC
G71-A
SMITH
SC
SCG900-41A
VICTOR
STANDARD
0309-0018 LARGE
VICTOR
C
0309-0003
OXWELD
TIP NUT
37Z23
OXY-FUEL
PUROX
PART
368
MULTI-USE® SYSTEM TIPS
MULTI-USE® SYSTEM TIPS
TIP NO.
DESCRIPTION
MACH TIP NO.
OXY-FUEL
M6
1 piece-medium preheat-acetylene tip
M6HS
1 piece Hi-speed acetylene tip
Machine ip
M6HSD7
1 piece Hi-speed acetylene tip
With stainless steel insert
LG
2 piece liq./natural gas tip
LGHS
2 piece Hi-speed liq./natural gas tip
Machine tip
LGHSD7
2 piece Hi-speed liq./natural gas tip
LGP
2 piece. fuel gas* tip
LGPHS
2 piece Hi-speed fuel gas tip
Machine tip
LGPHD7
2 piece Hi-speed fuel gastip
LGM
2 piece Mapp cutting tip
LGMHS
2 piece Hi-speed Mapp tip
Machine tip
LGMHSD7
2 piece Hi-speed Mapp tip
AM8
1 pc. Mapp cutting tip
PART
HTA
1 pc. acet. heating tip
HTG
2 pc. propane heating tip
HTM
2 pc. Mapp heating tip
MB
Acetylene brazing tip
* Fuel gas includes: Apachi®, Flamax®. H,P,G.®, Chemolene®, and other proplene based gases
369
OXY-FUEL
370
Notes
OXY-FUEL
Multi-Use
419
ATTC Multi-Use Adapters
And Tips For Oxy Fuel
Torches And Machines
MULIT-USE
Multi-Use
Multi-Use
420
Unretouched photo
showing a standard tip
and a Multi-Use Adapter
in use.
Tests have shown
Multi-Use System
components to be as
long lasting and efficient
as standard tips used
for the same purpose.
This is a standard
1 piece torch tip
showing the high
wear an d damage
area.
High wear and
damage area.
Once this area
is worn out,
Note the identical flames.
the whole tip must
be thrown away
A SIMPLE SYSTEM
MULIT-USE
This is the adapter.
It rarely wears out.
Keep this
This is the only portion
of the Multi-Use System
that has to be replaced.
Throw only this part out
Multi-Use
An assembled
Multi-Use adapter
and tip.
A simple effective
replacement system
that can save you
as much as 60%
in replacement
tip costs.
Multi-Use
421
Features And Benefits
The Multi-Use Universal
Adapter System Will Save
You Time And Money!
FEATURES
1. Every Multi-Use tip...
fits every Multi-Use adapter.
2. You need only one adapter for each torch.
3. Tips are available in six standard series...
and each series is available in a complete
range of sizes.
4. Each tip is quick and easy to change.
5. Tips are easy to clean and store.
6. All tips are made to exacting standards
using the highest quality materials.
7. Adapters and tips are available for all
gases.
Remove standard tip
Replace with Multi-Use adapter
And the most important benefit is ...you can
save up to 60% in replacement costs when
you use the American Multi-Use Adapter
System.
MULIT-USE
BENEFITS
1. Low initial cost.
2. Virtually eliminates torch head re-seating.
3. Inventory can be substantially reduced.
4. User can heat, cut or weld using the same
torch...just change the tip.
5. Increases production output by cutting
down-time.
6. Reduces replacement costs.
Oxy-acetylene torch with standard tip attached.
Screw Multi-Use tip onto adapter
Multi-Use
Multi-Use
422
THE MULTI-USE ADAPTER SYSTEM
ATTC is the patent holder of the unique Multi-Use
Adapter System... the system that can save you
up to 60% in oxy-fuel tip replacement costs. The
Multi-Use System is a simple and effective method
of saving money by speeding up down time due to
application tip changes or wear.
The average oxy-fuel tip costs between
$10.00 to $20.00, while the average
multi-use tip costs between $7.00 to
$8.00. This difference can represent a
savings of as much as 60%.
4 easy steps!
1. Choose gas and tip (column A)...
PREHEAT TIPNo.PART
MFG/TORCH
AIRCO® REGULAR
M6
M6HS
164, 261
275, 361
LG
AIRCO SMALL
1 pc. med. P/H acet. tip
1 pc.hi-speed acet. tip
2 pc. liq./natural gas tip
145,155
LGHS
ADAPTER No. PART
A-90
A-45**
2 pc. hi-speed liq./nat gas tip
LGP
2 pc. fuel gas* tip
AIR PRODUCTS®
LGPHS
121, M6
201, KGLG
2 pc.hi-speed fuel gas tip
KG
LGM
CRAFTSMAN®
LGMHS
B, BL
2 pc. hi-speed Mapp tip
CRF**
AM8
CIG®
41, 44
CIG
HTA
1 pc. acet. heating tip
ESAB®
HTG
2 pc. propane heating tip
IAD-300,
IPB-300
ESab
HARRIS®
H62**
HTM
2 pc. Mapp heating tip
MULIT-USE
6290, NX,NFF, VVC
MB
Acetylene brazing tip
A
HARRIS
C5
HARRIS
H-28
7490A, 7490BTU
2890F, 2890P
B
Multi-Use
Multi-Use
423
The new Multi-Use Machine
oxy-fuel tip saves up to 80% over
conventional machine cutting tips
and up to 60% over standard
multi-use tips. This increase in
longevity is made possible by a
specially designed stainless steel
insert which fits into the tip.
2. Choose adapter (column B) and ...
MFG/TORCH
ADAPTER No.
KOIKE®* KOI
KOI
102, 103
106, 106D7
MARQUETTE® MKT
MKT
GW-6, GWP
MECO® MCM
LA-6, LM
®
MG
ARS, PL-RC
MG
MG
PART
The tip also offers other time and
money saving benefits, such as
reduced downtime, easier removal
of carbon and slag buildup, prevention of orifice distortion and a longer
more productive life.
The Long Lasting Multi-Use tip can
be used on any style Multi-Use
adapter and is available in many
sizes for most gases.
MFG/TORCH
SMITH® SC
SC
SC12, SC50
SMITH
LC-6, LC-P SLT
TORCHWELD® T75
250, 251
TORCHWELD T36
650, 651 T36
NATIONAL / VERIFLOW N15**
TORCHWELD T30
243, 247 T30
25AA, 25PGS
OXWELD® / L-TEC® 032
032
PUROX® / L-TEC PE**
PE**
4202, 4203
4213-14
REGO®
RKX
KX-6, KX-105 RKX
REGO CCL
CCL
NC
B
VICTOR®
V40
1-101, GPN V40
MTHN
VICTOR®*
C14**
3-101, 3GPN C14**
WELDIT® W37
W37
MULIT-USE
1502, 1534, 1535
1566, 1567
PART
g1-AD, G1-P, G1-T
NATIONAL / VERIFLOW N400
N400
A, LPG
ADAPTER No.
SAF® SAF
SAF
S, SP
ZINsER® ZIN
ZIN
B
Multi-Use
Multi-Use
424
MULIT-USE
Stocking And Shipping
Our distribution center oversees an inventory that contains
millions of parts. They also track them in detail so
manufacturing produces parts
needed to maintain in-stock
status on catalog items.
We ship around the clock to
customers in the United States
and to more than 45 countries
around the globe. From this
facility we stock our branch
warehouses in Canada and
Taiwan enabling ATTC to ship
most products for next day
delivery.
Keeping you up-and-running is our most important
job.
Guarantee
The American Torch Tip Company products are guaranteed
against any material or manufacturing defects, to reach
your plant intact and to give
complete satisfaction under
normal working
conditions.
Multi-Use
Unlisted Items
If you require a part not listed in
our catalog, be sure to call us.
We are continually adding new
products, developed for special
applications or for private label,
and cannot always include
these in our catalogs.
Manufacturing
American can design for
special application, manufacture from print and supply
samples or large quantities
to meet most time requirements.
Quality Control
The company has established
and maintains the highest
standards for quality control.
All parts are CNC machined
and assembled to very precise
tolerances. Product quality is
further maintained by process
control, statistical batch analysis and 100% inspection of
consumable parts for critical
characteristics.
Thank You
For Buying
American Torch Tip
Products.
Multi-Use
425
3. Decide thickness of metal and ...
4. Oxy-fuel cutting pressure
Standard Pressure- - Propane, Natural Gas - LG / Propyle
Metal
Thickness
Inches/mm
3/16
5/8
1
2
3
4
7
10
12
14
/
/
/
/
/
/
/
/
/
/
5
16
25
51
76
102
178
254
305
356
No
00
0
1
2
3
4
5
6
7
8
Cutting
Oxygen
Orifice
68
60
56
53
51
45
39
31
25
20
Cutting
Oxygen
PSI / Bar
30-40 / 2.1-2.8
35-45 / 2.4-3.1
30-50 / 2.1-3.5
40-50 / 2.8-3.5
40-50 / 2.8-3.5
45-65 / 3.1-4.5
60-75 / 4.2-5.2
60-90 / 4.2-6.3
60-90 / 4.2-6.3
60-90 / 4.2-6.3
Fuel Gas
PSI / Bar
Cut Speed
Inches-min. / mm-min.
3-5 / 0.2-0.34
3-6 / 0.2-0.4
3-6 / 0.2-0.4
4-8 / 0.3-0.55
4-8 / 0.3-0.55
5-10 / 0.34-0.7
8-12 / 0.55-0.8
9-15 / 0.6-1.0
9-15 / 0.6-1.0
9-15 / 0.6-1.0
17-24 / 430-610
16-22 / 405-560
14-18 / 355-460
12-16 / 305-405
10-14 / 255-355
8-12 / 230-305
5-8 / 130-230
3-5 / 80 -127
3-4 / 80 -100
2-3 / 50 -80
Kerf Width
Inches/mm
.05 / 1.3
.06 / 1.5
.08 / 2.0
.09 / 2.3
.10 / 2.5
.12 / 3.0
.15 / 3.8
.21 / 5.3
.24 / 6.1
.26 / 6.6
High Pressure - Propane, Natural Gas - LGHS / Propylene - LGPHS / MAPP Gas - LGMHS
Metal
Thickness
Inches/mm
3/16
1/4
3/8
1/2
3/4
1
2
3
4
5
7
10
/
/
/
/
/
/
/
/
/
/
/
/
5
6
10
13
19
25
51
76
102
127
178
254
No
00
0
1
2
3
4
5
6
7
8
10
12
Cutting
Oxygen
Orifice
Cutting
Oxygen
PSI / Bar
72
68
65
60
56
55
54
53
52
49
44
39
50-100 / 3.5-7.0
70-100 / 4.9-7.0
80-100 / 5.6-7.0
80-115 / 5.6-8.0
80-115 / 5.6-8.0
80-115 / 5.6-8.0
80-115 / 5.6-8.0
80-115 / 5.6-8.0
80-115 / 5.6-8.0
80-115 / 5.6-8.0
80-115 / 5.6-8.0
80-115 / 5.6-8.0
Fuel Gas
PSI / Bar
2-5 / 0.1-0.34
2-5 / 0.1-0.34
3-5 / 0.2-0.34
3-5 / 0.2-0.34
3-6 / 0.2-0.4
3-6 / 0.2-0.4
3-6 / 0.2-0.4
4-8 / 0.3-0.55
4-8 / 0.3-0.55
5-9 / 0.34-0.6
6-10 / 0.4-0.7
9-15 / 0.6-1.0
Cut Speed
Kerf Width
Inches/mm
23-29 / 580-735
21-28 / 530-710
19-26 / 480-660
18-26 / 460-660
16-24 / 410-610
15-20 / 380-510
12-16 / 305-405
10-15 / 254-380
9-12 / 230-305
8-11 / 200-280
8-10 / 200-255
4-6 / 100-150
.04 / 1.0
.05 / 1.3
.05 / 1.3
.05 / 1.3
.06 / 1.5
.06 / 1.5
.06 / 1.5
.07 / 1.8
.08 / 2.0
.09 / 2.3
.10 / 2.5
.17 / 4.3
High Speed Cutting W/Stainless Steel Inserts - Propane, Natural Gas - HSD7 / Propylene - PHSD7 / MAPP - MHSD7 / Acetylene - AHSD7
Metal
Thickness
Inches/mm
3
6
10
13
19
25
38
51
64
76
102
127
152
230
254
Cutting
Oxygen
Orifice
Cutting
Oxygen
PSI / Bar
00
0
0
1
2
2
3
4
5
5
6
6
7
7
8
78
74
74
65
57
57
55
53
50
50
45
45
38
38
30
100 / 7.0
100 / 7.0
100 / 7.0
100 / 7.0
100 / 7.0
100 / 7.0
100 / 7.0
100 / 7.0
100 / 7.0
100 / 7.0
100 / 7.0
100 / 7.0
100 / 7.0
100 / 7.0
100 / 7.0
Fuel Gas
PSI / Bar
2-5 / 0.1-.034
2-5 / 0.1-.034
2-5 / 0.1-.034
2-8 / 0.1-0.55
3-5 / 0.2-0.34
3-5 / 0.2-.034
3-6 / 0.2-0.4
3-6 / 0.2-0.4
3-6 / 0.2-0.4
3-6 / 0.2-0.4
4-8 / 0.3-0.55
4-8 / 0.3-0.55
4-8 / 0.3-0.55
4-8 / 0.3-0.55
5-9 / 0.34-0.6
Cut Speed
31.5
29 /
27 /
25 /
22 /
20 /
18 /
16 /
14 /
12.5/
10 /
9 /
7 /
5.5 /
4 /
/ 800
735
685
635
560
510
460
405
355
320
255
230
180
140
110
Kerf Width
Inches/mm
.03 / 0.8
.04 / 1.0
.05 / 1.3
.05 / 1.3
.06 / 1.5
.07 / 1.8
.08 / 2.0
.10 / 2.5
.11 / 2.8
.11 / 2.8
.13 / 3.3
.14 / 3.6
.14 / 3.6
.18 / 4.6
.20 / 5.1
MULIT-USE
1/8 /
1/4 /
3/8 /
1/2 /
3/4 /
1
/
1-1/2 /
2
/
2-1/2 /
3
/
4
/
5
/
6
/
8
/
10
/
No
lgphsd7 = Propylene Style Shell
LGMHSD7 = Mapp Style Shell
LGHSD7 = Propsne/Natural Gas Shell
**Pressures are approximate. You may have to vary pressure with feeds and speeds for optimum results.
Multi-Use
Multi-Use
426
Notes
MULIT-USE
Multi-Use

OXY-FU EL

Transcription

Similar documents

Goss Torch Tip Catalog

Oxweld Model W-I7 I Welding Torches - Seal-Seat

Gas Apparatus Solutions From ESAB