User Manual

JIG 3
User Manual
：
Released by Chris Gao
Firmware R&D Center
Revision 1.0.1.4
October 14, 2011
ASUSTeK Confidential
PROPRIETARY INFORMATION
This document contains information proprietary to ASUSTeK Computer Inc.
Use or disclosure without permission of an offer of ASUSTeK is expressly forbidden.
ASUS JIG Board User Manual
Tables of Content
1
2
JIG3 Board Overview .......................................................................................... 2
Update the target board’s BIOS ROM ................................................................ 3
2.1
Connect JIG3 and update Flash............................................................................... 3
3
Read Target board’s BIOS ROM ......................................................................... 7
3.1
Connect JIG3 to Target board ................................................................................. 7
3.2
Read BIOS ROM by using EC_JIG_WinFlash........................................................ 8
4
Appendix A ......................................................................................................... 10
KeyBoard Connector............................................................................................................... 10
GPNV..................................................................................................................................... 11
ASUSTeK Confidential
1
October 14, 2011
ASUS JIG Board User Manual
JIG3 Board Overview
1
0B
CN1
CN2
J301
LED2
U1
BTN1
LED3
LED1
SW1
J302
LED4
BTN2
BTN3
BTN4
CN1
USB connector.
CN2
GND connector.
BTN1
Main power button.
BTN2
RESET button
BTN3
Start button.
BTN4
Function button.
LED1
Software On Power LED.
LED2
Good, Fail, Busy, PWR LED
LED3
Function indicator LED
LED4
Message ID LED indicator.
SW1
U1
Function Switch
SPI Flash IC
J301
UP connect connector
J302
Down connect connector
ASUSTeK Confidential
2
October 14, 2011
ASUS JIG Board User Manual
Update the target board’s BIOS ROM
2
2B
2.1 Connect JIG3 and update Flash
6B
Step 1: Remove all power sources (include battery and power supply) from target board.
Step 2: Connect USB cable from CN1 to your PC’s USB connector.
J301
USB
GND
Pin 1
J302
Step2
Step 3: Connect FPC cable from J301(UP connect) or J302(Down connect) to your target board’s
keyboard connector, choice J301 or J302 by target board connector type. Make sure JIG3 J30x’s
Pin1 is connected to target board keyboard connector’s Pin1.
Step3
Step4: Use a usb cable make common ground between JIG3 and target board. Connect JIG3 CN2
and usb port of taget board, and make sure all power sources was removed form target
board.
ASUSTeK Confidential
3
October 14, 2011
ASUS JIG Board User Manual
Step5: Set SW1 to 0000.
Step 6 Press POWER button to turn on power. Power led will turn on.
Step 7 Check LED4 will show 00.
Step7
Step 8: Run ASUS_WinFlash utility.
Step 9: Check Protect NVRAM to Protect GPNV(Appendix A). (Can choose protect it or not)
Check
Step9
Step 10: Press LoadFile
icon to load BIOS ROM file.
Step 11: Press AutoBurn
icon to burn BIOS ROM file to Target board.
ASUSTeK Confidential
4
October 14, 2011
ASUS JIG Board User Manual
Step 12: The message will show to turn on EC power and check ITE EC Power-Off
Step12
Check
Step 13: Turn on power and check “ITE EC Power-On”
Step13
Check
ASUSTeK Confidential
5
October 14, 2011
ASUS JIG Board User Manual
Step 14: When this message show on the screen, choose pre backup BIOS ROM before burning or
not.
Step 15: After burning done, press POWER button again to turn off main power and turn off the
ASUS_WinFlash utility. At this time you can remove all devices form target board.
ASUSTeK Confidential
6
October 14, 2011
ASUS JIG Board User Manual
Read Target board’s BIOS ROM
3
3B
3.1 Connect JIG3 to Target board
7B
J301
Pin 1
J302
GND
ASUSTeK Confidential
7
Step 1: Remove all power sources
(include battery and power
supply) from target board.
Step 2: Connect USB cable from CN1
to your PC’s USB connector.
Step 3: Connect FPC cable from J301
or J302 to your target board’s
keyboard connector, make sure
JIG3 J30x’s Pin1 is connected to
target board keyboard
connector’s Pin1.
Step4: Use a usb cable connect GND
between JIG3 CN2 and taget
board usb port, and make sure
all power sources was removed
form target board.
October 14, 2011
ASUS JIG Board User Manual
3.2 Read BIOS ROM by using EC_JIG_WinFlash
8B
Step 5: Connect USB cable from
CN1 to your PC’s USB
connector.
Step 6: Set SW1 to 0000.
Step 7: Press POWER button to turn
on power. Power led will turn
on.
Step 8 Check LED4 will show 00.
：
Step8
Step 9: Check the USB Device “Asus
JIG3” is Plug-In and ITE EC
Power-Off.
10
Check
Check
Step 10: Press
Read Rom
icon to read BIOS ROM from
target board.
Step11: When this Message show on
screen. Turn on target board
power.
Step12: If “ITE EC Power-On”, click
“YES” to start read flash.
Else check target board
power, FPC cable, GND and
redo Step 7.
ASUSTeK Confidential
8
October 14, 2011
ASUS JIG Board User Manual
When show this dialog ,
Check FPC cable and GND or
update Bios to JIG first.
ASUSTeK Confidential
9
October 14, 2011
ASUS JIG Board User Manual
4
4B
Appendix A
KeyBoard Connector
Up Connector: The pin connect on the up side
Down Connector: The pin connect on the down side
ASUSTeK Confidential
10
October 14, 2011
ASUS JIG Board User Manual
GPNV
GPNV is one of the BIOS ROM sections that have important information. So, when Protect
NVRAM checked, we will protect this section can’t be replaced. GPNV is searched by the index
“BIOSINFO”. Normally, it only can use after Huron River platform.
ASUSTeK Confidential
11
October 14, 2011