Buyers Guide - Powers Fasteners

Transcription

Buyers Guide
2 0 1 6
Powers Fasteners has been developing and manufacturing innovative fasteners for more than
90 years & has the largest range of fasteners for attaching to concrete, masonry, steel and
wood. Powers is the worldwide leader in code-approved fastening solutions with product
availability in more than 50 countries. World class fastening design software, technical literature
and technical support has made Powers a leading choice for designers and specifiers.
We are pleased to present to you our latest Buyers Guide. Our comprehensive catalog
was developed for both distributors and contractors. The Powers Buyers Guide contains the
latest products and innovations in anchoring technology. This catalog should serve as a
quick reference for ordering and for help in selecting the right anchor for your next
fastening application.
For technical data relating to any of the products contained in the catalog, we ask that you
refer to our latest technical information or by visiting our website at www.powers.com.
This site contains the most up-to-date product information including product approvals and
listings, MSDS sheets, submittal packages, general product information, software tools and
contact information. These resources and programs combined with over thirty stocking
locations throughout North America provide the best possible product and field support
available in the post-installed anchoring industry.
If you should have any questions or feedback, please contact customer service at
1(800) 524-3244 or by email at [email protected].
Product Warranty Statement Powers Fasteners, Inc. will repair or
replace, at its sole discretion, any product within 90 days after sale by
Powers Fasteners, Inc. or its distributors, if found to be defective in material
or workmanship,normal wear and tear excluded.
Limitation of Liability Powers Fasteners, Inc. shall not be liable for any
injury, loss or damage, direct, indirect, incidental or consequential, arising out of
the use of, or the ability to use, the products described herein.
This warranty does not apply to products not used in compliance with published Indemnity Any or all modifications made by the customer to either the
product itself or the installation procedures, shall, regardless of specific
instructions, specific applications, installment procedures, modified products,
defective substrate materials or deterioration due to environmental conditions. instructions to the user, indemnify, defend, and hold harmless, Powers Fasteners,
Inc. for any and all claimed loss or damage occasioned, in whole or in part, by
All warranties are expressed in lieu of other warranties, expressed or implied,
the modified products.
including warranties of merchantability or fitness for a particular purpose, all
such other warranties being hereby expressly excluded.
EXPANSION FOAMS
PowerFoam™
39
TriggerFoam Pro
39
BONDING SEALANTS
40
PowerStick™
PowerPatch™
40
LIGHT DUTY ANCHORS
Selection Guide
41
METAL ANCHORS
42
Wall Dog®
Scru-Lead
42
Toggle-Bolt
42
Polly
43
Legs
43
Zip-All®
44
PLASTIC ANCHORS
Sharkie
44
44
Strap-Toggle™
Self-Drilling Strap Toggle
44
44
Zip-It® and Zip-It® Jr.
Zip-Toggle®
45
45
Poly-Toggle®
Pop-Toggle™
45
Bantam Plug
36
Fluted Plastic Anchor
45
POWDER ACTUATED FASTENING
Selection Guide
46
FASTENERS
0.300" Head Drive Pins
47
0.300" Head Drive Pins with Washers
47
ACQ Drive Pins for Pressure Treated Lumber
47
8mm Head Drive Pins
48
8mm CSI Spiral Pins
48
8mm Head Drive Pins with Washers
48
8mm Head Collated Spiral CSI Pins
48
8mm Head Collated Drive Pins
48
Threaded Studs
49
Hammer Drive Pins
49
ACCESSORIES
Ceiling Clip Assemblies
49
BX & EMT Conduit Clip Assemblies
50
Rod Hanging Clip Assemblies
50
CSI Clip Assemblies
50
Rebar Basket Assemblies
50
TOOLS
P1000
51
T1000
51
P2201
52
P35s
52
P3500
53
PA3500
53
P3600
54
54
Sniper™ Pole Tool
POWDER LOADS
.22 Caliber Singles
55
.27 Caliber Singles
55
.25 Caliber Strips
55
.27 Caliber Strips
55
55
.27 Caliber Safety Strip®
GAS FASTENING
Selection Guide
Trak-It® C5
C3 Trak-It® Pins
Trak-It® Stick-E
ROOFING FASTENERS
Selection Guide
Spike® Perma-Seal®
Powerlite™
Deck Screws
Twin Fast Screws
Stress Plates
CARBIDE DRILL BITS
Selection Guide
Fat-Head™
S-4 Plus SDS
Accu-Bits™
Industrial Grade Bits (Value Paks)
4-X Cutter SDS-Max Shank
4-X Cutter Spline Shank
Single Tip Spline Shank
HD Straight Shank
IG Straight Shank
“A” Taper
Rotary Carbide Bits
Rebar Cutter
Heavy Duty Chisels
One and Two Piece Core Bits
Screws & bolts
Selection Guide
Zinc Products
Stainless Steel Products
Domestic Products
Brass Products
Products in Jars
Accessories
Gaskets
Kits
Electrical Products
56
58
59
59
60
61
61
62
62
62
Co ntents
2-3
ANCHOR SELECTION CHART
MECHANICAL ANCHORS
Selection Guide
8-9
EXPANSION ANCHORS
PB+ (Power-Bolt+)
13
PB-Pro
13
13
Power-Bolt®
Power-Stud+® SD1
14
Power-Stud+® SD2
14
Power-Stud+® SD4 + SD6
15
Power-Stud® HD5
15
Power-Stud®
16
Lok-Bolt AS®
17
Set-Bolt
18
Undercut ANCHORS
16
Atomic+ Undercut®
SCREW ANCHORS
Wedge-Bolt+
19
Wedge-Bolt
19
Tapper+® Xtreme
20
Tapper+®
21
22
Stainless Steel Tapper®
BOLT & SHIELD ANCHORS
23
Snake+®
23
Smart DI+®
Hollow-Set Dropin™
23
Steel Dropin
24
Mini Dropin
24
Double
25
Single
25
Calk-In
25
Lag Shield
26
ROD HANGING SYSTEMS
& CONCRETE INSERTS
26
Vertigo® / Vertigo®+
27
Bang-It™
Wood-Knocker™
27
FACADE, PIN & NAIL ANCHORS
26
Heli-Pin™
27
Spike®
DRIVE®
28
Zamac Hammer-Screw®
29
Safe-T+ Pin
29
29
Zamac Nailin®
Nylon Nailin®
30
ADHESIVES
Selection Guide
31
INJECTION ADHESIVES
33
Pure110+®
AC100+Gold®
34
PE1000+®
35
36
Pure50+™
AC50 Silver™
36
GLASS CAPSULE ADHESIVES
Chem-Stud®
37
Hammer-Capsule®
38
ADHESIVE ACCESSORIES
Installation Accessories
38
Screen Tubes
38
63
64
64
65
65
65
66
66
66
67
67
67
67
68
68
70-71
72
80
84
86
86
91
92
93
95
1
Hollow Core Plank
Lightweight Concrete
Concrete
■
■
■
□
□
□
Screw Anchor
316 SS Wedge-Bolt
Screw Anchor
■ ■
■
■
■ ■ □ ■ □ ■
Wedge-Bolt+
Sleeve Anchor
□
■
■
■
■
■ ■ □ ■ ■ ■ □
■ ■
■ ■
■ ■
■ ■ □ ■ □ ■ □
■ ■
■ ■
■ □
■ □
■ □ □ □ □ □ □
■ ■ □ ■ ■ ■ □
■ ■ □ ■ □ □ □ □
Lok-Bolt AS ®
®
Grout-filled Concrete Masonry
■ ■
Expansion Anchor
Unreinforced Masonry
■ ■ □ ■ ■ □ □ □
Hollow Concrete Masonry
Power-Stud ® (MG, SS)
Expansion Anchor
Concrete & Masonry
®
®
®
®
®
®
®
®
Solid Brick
■ ■
Concrete
Concrete
Concrete & Masonry
Concrete
Concrete
Concrete & CMU
Concrete
Concrete
Hollow Brick
Power-Stud ® HD5
Expansion Anchor
Power-Stud ®+ SD4/SD6
Expansion Anchor
Power-Stud ®+ SD2
Expansion Anchor
Power-Stud ®+ SD1
MEDIUM DUTY
Heavy Duty Sleeve Anchor
Power-Bolt ®
Heavy Duty Sleeve Anchor
Power-Bolt ®+
Undercut Anchor
Atomic+ Undercut ®
HEAVY DUTY
Glass Capsule - Spin Type Anchor
Chem-Stud ®
Glass Capsule - Hammer Type Anchor
Hammer-Capsule®
10-to-1 Cartridge - Vinylester Anchor
AC50 Silver™
10-to-1 Cartridge - Vinylester Anchor
AC100+ Gold ®
3-to-1 Cartridge - Epoxy Anchor
PE1000+®
1-to-1 and 3-to-1 Cartridge - Epoxy Anchor
Pure110+®
ADHESIVE SYSTEMS
1/4” - 1/2”
1/4” - 3/4” (CS)
3/8” - 3/4”
(MG)
1/4” - 3/4” (CS)
1/4” - 5/8” (SS)
1/2” - 1” (MG)
1/4” - 1” (SS)
1/2” - 5/8”
1/4” - 3/4”
3/8” - 3/4”
1/4” - 1-1/4”
1/4” - 3/4” (CS)
1/4” - 1/2” (SS)
1/4” - 3/4”
5/8” - 1-1/8”
(nom 3/8” - 3/4”)
3/8” - 1-1/4”
#3 - #10 Rebar
3/8” - 1”
#3 - #8 Rebar
3/8” - 1”
#3 - #8 Rebar
3/8” - 1-1/4”
#3 - #10 Rebar
3/8” - 1-1/4”
#3 - #10 Rebar
3/8” - 1-1/4”
#3 - #10 Rebar
Anchor
Diameter
Stud
■
■
■
■
■
■
■
■
■
■
■
■
■
Finished Hex Head
■
■
■
■
Flat Head (countersunk)
Round / Acorn Nut
■ ■
■
Tie-Wire Head
Female / Rod Coupler
■ ■
■
Zinc Plated Carbon Steel
Over 5,000 lbs.
500 lbs. to 5,00 lbs.
Under 500 lbs.
Flush Mount
■
■ ■ ■
■ ■
■
■
■
■
■ ■ ■
■
■ ■ ■ ■ ■
■ ■
■ ■ ■
■ ■ ■
■ ■ ■
■ ■ ■ ■
■ ■ ■ ■
■ ■ ■ ■
■ ■ ■ ■
■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■
Galvanized Steel
Mushroom Head
Coating / Material
Type 303/304 Stainless Steel
Wkg.
Load
(Concrete)
Type 316 Stainless Steel
Head Style
Base Material
Zamac Alloy
Anchor Selection Chart
Perma-Seal Coated
2
Lead
Nylon / Plastic
Drywall
Steel
1, 4
3
1
1, 2, 3, 4
1, 2, 3, 4
3
1
1
1, 6
1, 6
1, 6
1. ICC-ES
2. FM
3. UL
4. COLA
5. MiamiDade
6. NSF 61
7. Core
Approvals
No Similar Product
Hilti Kwik HUS / HUS-EZ
Simpson Titen HD
Red Head Large Dia.
Tapcon (LDT)
Hilti HLC
Simpson Sleeve-All
Red Head Dynabolt
Hilti Kwik Bolt 3 (KB3)
Simpson Wedge-All
Hilti Kwik Bolt 3 (KB3) HDG
Red Head Trubolt
Hilti Kwik Bolt 3 (KB3) /
KB TZ SS
Simpson Strong-Bolt 2
Red Head Trubolt
Hilti Kwik Bolt TZ
Simpson Strong-Bolt
Red Head Trubolt+
Hilti Kwik Bolt 3 (KB3)
Simpson Strong-Bolt 2
Red Head Trubolt
Hilti HSL
Hilti HSL-3
Hilti HDA Undercut
Hilti HVU Capsule
ITW Maxima 7 Spin Capsule
Simpson VGC Capsule
ITW Chemset Hammer Cpsl.
Simpson AT
Red Head Epcon A7
Hilti HY 200/ HY 150 MAX
Simpson AT - XP
Red Head Epcon S7
Hilti RE 500-SD / RE 500
Hilti RE 500-SD / RE 500
Simpson SET-XP
Red Head Epcon G5, C6+
Similar
Anchoring
Products
3
Indicates a Code Listed Product
■ ■ ■ ■ ■ ■ □
■ ■
Hollow-Set™ Dropin
Double™
®
■ ■ ■ □
Mini Dropin™
■ □ □ ■ ■ ■ □
■ □ □ ■ ■ ■ □
■ □
Zamac Hammer Screw ®
Zamac or Nylon Nailin ®
Calk-In™
□
Strap-Toggle™
■: Suitable
□: May Be Suitable
Wall Dog ® Drywall Anchor
Drywall Anchor
Zamac or Nylon Zip-It ®
Hollow Wall Anchor
□
■
■
3/16”
#10, 6, 8 Screw
3/16” - 1/2”
1/8” - 1/2”
3/16” - 1/2”
3/16” - 1/2” (CS)
3/16” - 3/8” (SS)
■
■
■
■
■
■ ■
■ ■ ■
■ ■
■ ■
■
■
■ ■
■ ■
■
■ ■
■ ■
■
■ ■ ■
■
■
■
■ ■
■
■
■ ■
■ ■
■ ■ ■
■ ■ ■
■ ■ ■
■ ■ ■
■ ■ ■
■ ■ ■ ■
■
■
■ ■ ■
Hilti is a registered trademark of Hilti Corp. ITW and Redhead are registered trademarks of Illinois Tool Works, Inc
■ ■ ■ ■
■
■
■
■ □ ■
Simpson is a registered trademark of Simpson Strong-Tie Company, Inc
□
Hollow Walll Anchor
Toggle-Bolt™
Bolt/Shield Anchors
Pin / Nail Anchors
Pin / Nail Anchor
■ ■
#8-32 - 1/2”
□
■ □
DRIVE ®Pin / Nail Anchors
□
■
■
3/16” - 1/4”
■
■ ■
Spike ® Pin / Nail Anchors
■
3/16” - 1/4”
■
■ ■
Safe-T+ Pin® Pin / Nail Anchors
8mm
3/16” - 1/4”
■
■
Tapper+® Screw Anchor
■ ■
1/4” - 5/8”
Tapper (SS)™ Screw Anchor
□
1/4” - 3/4”
1/4” - 5/8”
1/4” - 1/2”
1/4” - 3/4”
1/4” - 3/4”
1/4” - 3/4”
1/4” - 1/2”
3/16” - 5/16”
□
■
1/4” - 1/2”
1/4” - 1/2”
■ ■ ■ ■ ■ ■ □
LIGHT DUTY
Bolt/Shield Anchors
Single™
Bolt/Shield Anchors
Dropin Anchor
Dropin Anchor
Dropin Anchor
■ □
■ ■
Steel Dropin™
■ ■ ■
■ □
Dropin Anchor
Smart DI+®
Speciality Cast-In-Place
Concrete, Wood,
ACQ & CMU
■ ■
®
■ ■
■ ■ □ □
Bang-It /
Wood-Knocker™
™
Rod Hanger / Screw Anchor
Concrete
®
®
■ ■ ■
Concrete
Concrete
Vertigo® (Steel / Wood)
Vertigo®+ (Concrete)
Snake+®
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■ ■
■
■
■
■
■
■
■ ■
■
■
■
■
■
■
■
■
3
5
1, 5
3
2
3
2, 3
1, 2, 3
3
1, 2
1, 2, 4
No Similar Product
ITW EZ
Hilti HTB Toggler Bolt
No Similar Product
Simpson MSD/CSD/DSD
Simpson Crimp
Red Head Redi-Drive
No Similar Product
Hilti Kwik-Con II
Simpson Titen
ITW Tapcon
Hilti Kwik-Con II
Simpson Titen / Titen HD
Redhead Tapcon
No Similar Product
Hilti HDI-P Short Drop-In
Red Head RX Drop-In
Hilti HDI Drop-In
Red Head RL Drop-In
Hilti HDI Drop-In
Red Head RL Drop-In
Hilti HCI-WF / HCI-MD
Simpson Blue Banger
ITW Sammy
Hilti HUS-EZ I
Simpson Titen HD Rod
Hanger
No Similar Product
The newly updated Powers
Design Assist (PDA2) anchor design
interface has next-generation
features that put technical
data into a dynamic real-time
environment to better
help you visualize, consider and
specify anchors.
Refined features include:
• Modernized user interface (Dashboard)
• Adhesive & cast-in-place anchoring now included
• Detailed calculation output, including ACI 318-08 references
With concrete anchor design still in 5 easy steps, all the details
design professionals need to choose the right anchor are right
on your desktop. With the expanded line of Strength Design
products available, you’ll have the tools, the data and the
anchors to specify with confidence. PDA2 delivers better anchor
technology at your fingertips, and the software is FREE!
Just go to www.powersdesignassist.com
4
FREE PDA SOFTWARE!
Submittals & Substitutions Have
Never Been This Simple
POWERS SUBMITTAL
GENERATOR
Powers Launches New Submittal Builder tool!
Putting together a submittal for Powers fastening products has never been easier!
Pick only the reports and product
information pages you would like
included. View submittal sections
directly in your browser.
Choose different cover sheet options
including a full online version that
allows you to create a submittal
directly in your browser or from a
mobile device.
Save your submittal
information for quick
access on the next
submittal.
Create a completely
editable PDF file.
5
Why sell code approved anchors? It’s now the LAW.
Code
listed
ICC-ES ESR-3260
Power-Bolt®+
Code
listed
ICC-ES ESR-2818
ICC-ES ESR-2966
The International Building or Residential Codes (IBC or IRC) have been
adopted in all 50 states. The building codes serve as the basic design and
enforcement requirements that an owner, engineer, contractor, inspector
and/or code official uses to produce safe structures today. It also applies
to renovations of existing buildings requiring construction to meet current
code requirements. These structures include everything from condos,
shopping malls, hospitals, schools and high-rise construction to ordinary
home construction.
Power-Stud®+
SD1
Code
listed
ICC-ES ESR-2502
Power-Stud®+
SD2
Code
listed
ICC-ES ESR-2502
Power-Stud®+
SD4 + SD6
Code
listed
The IBC and IRC specifically require anchors that meet the code. Since all
states have adopted the building code with enforcement, there are very
significant ramifications for any contractor using products not compliant
with the code. Compliance with these codes is as simple as providing
a Powers approval report or knowing that one exists when selling,
specifying or using our product.
Powers has the most ICC-ES code approval reports for anchoring
products in structural applications. Powers also has numerous test reports
on anchor products using state-of the-art research and development
laboratories which, with acceptance by a local inspector or building
official, can serve as proof of compliance.
ICC-ES ESR-2526
ICC-ES ESR-1678
Wedge-Bolt+
Code
listed
ICC-ES ESR-2272
Snake+®
Code
listed
ICC-ES ESR-3067
Atomic+
Undercut®
6
Code
listed
ICC-ES ESR-2526
®
Vertigo +
Code
listed
ICC-ES ESR-3068
Tapper+® Xtreme
Code
listed
ICC-ES ESR-3068
ICC-ES ESR-3042
ICC-ES ESR-3213
ICC-ES ESR-3196
Tapper+®
Construction distributors should be selling only anchors that comply with
the building codes since IBC and IRC are nationally adopted codes. The
code also applies to non-structural anchoring applications. Mechanical
anchors and adhesive anchors are purchased and used every day by
contractors of all types in structural and non-structural applications.
There are several key reasons why everyone should be selling,
specifying and using only concrete anchors that are code listed:
1. Code listed anchors normally offer significantly
higher performance
2. Powers can offer these products at a competitive cost
and in a complete range
3. Compliance with state and local building authorities’
regulations (AHJ)
4. Independent qualification and certification of
product performance
5. Proof of usability and conformance in all 50 states
6. Usability and conformance in wind and seismic
areas (Florida and California)
7. Increased product safety, reliability and confidence
8. Minimize risk for all applications
(structural or non-structural)
9. Enforcement and penalties for noncompliance are costly
10. Building inspection for compliance is common
Code
listed
ICC-ES ESR-3263
TriggerFoam Pro™
Code
listed
ICC-ES ESR-2582
ICC-ES ESR-3200
AC100+Gold®
Code
listed
ICC-ES ESR-2583
PE1000+®
Code
listed
ICC-ES ESR-3576
Pure50+™
Code
listed
ICC-ES ESR-3298
Pure110+®
Code
listed
Code
listed
ICC-ES ESR-3657
™
ICC-ES ESR-2024
™
Bang-It & Wood-Knocker
CSI Drive Pin
Code
listed
ICC-ES ESR-3275
®
Trak-It C5 Pins
Code
listed
ICC-ES ESR-3275
Trak-It® C4 Pins
7
10 • •
Power-Bolt
01 • •
Power-Stud+ SD1
• • •
•
•
• • •
• • • • • •
•
• •
•
12 • •
•
•
Power-Stud+ SD2
12 • •
•
Power-Stud+
SD4/SD6
13 • •
•
Power-Stud HD5
13 • •
Power-Stud
14 • •
•
•
Lok-Bolt AS
15 •
• • •
Set-Bolt
16 •
Atomic+ Undercut
14 • •
Wedge-Bolt+ /
Wedge-Bolt
17 • •
Tapper+X /
Tapper+ / Tapper
18 • • • • • •
•
Vertigo+ / Vertigo
25 • • •
• •
Bang-it
Wood-Knocker
•
•
Nylon/Plastic
Perma-Seal Coated
Code Recognition
ICC-ES ESR 3260
•
•
ICC-ES
ESR-2818 & 2966
LARR-25787
& 25864
•
ICC-ES ESR-2502
LARR-25831
• • • • • • •
•
• • • •
•
• • •
•
• • • •
•
• • • • • • •
•
• • • • • •
• • • • • •
• • •
• • •
•
• •
•
•
• • • •
•
• •
•
ICC-ES ESR 3067
• •
•
ESR-2526 & 1678
LARR-25808
•
•
• • • •
• • •
•
Galvanized Carbon Steel
Plated Carbon Steel
Female Coupler
Tie-Wire Head
Coating/Material
Removable
Flat Head (Countersunk)
Round/Acorn Head
Hex Head
Finished Hex Head
1-1/4" (28mm)
1" (24mm)
7/8"
3/4"
5/8"
1/2"
Head Style
• • • •
May be Suitable
•
3/8"
5/16"
1/4"
Steel
Wood
Structural Clay/Tile
Stone
Hollow Brick
Anchor Diameter
Solid Brick
Hollow Core Plank
Page
Expansion Anchors
Screw Anchors
Rod Hanging System
PB+ (Power-Bolt+)
/ PB-Pro
• Suitable
8
Concrete
Base Material
3/16"
MECHANI CAL
SELECTION GUIDE
• •
ICC-ES ESR 2502
•
•
•
•
• •
•
•
•
ICC-ES ESR-3068,
3042, 3213;
3196
Miami-Dade NOA
• •
•
• •
• •
26 • •
•
• • • •
• •
•
ICC-ES ESR-3567
26 • •
•
• • • •
• •
•
ICC-ES ESR-3567
ICC-ES ESR-2526
SELECTION GUIDE
Snake+
22 • •
•
• •
• •
Smart DI+
22 •
•
• •
• •
Hollow-Set Dropin
22 •
Steel Dropin
• • • •
• •
•
23 • •
•
• • • •
• •
• •
Mini Dropin
23 • • •
•
• •
• •
Double
24 •
Single
25 •
Calk-In
26 •
Lag-Shield
27 •
• •
Heli-Pin
28 •
• • •
Spike
26 • •
•
Drive
27 •
Safe-T+ Pin
28 • •
•
•
•
•
•
• • • • •
•
•
•
•
•
• • • • • •
•
•
• •
•
Lead
Nylon/Plastic
Perm-Seal Coated
•
• • • • • •
• • • •
Code Recognition
ICC-ES ESR-2272
LARR-25810
• • • • •
• •
Zamac Alloy
Galvanized Carbon Steel
Plated Carbon Steel
Flush Mount
Tamperproof
Coating/Material
Removable
Tie-Wire
Round Head
Mushroom Head
Head Style
3/4"
5/8"
1/2"
3/8"
5/16"
1/4"
3/16"
Steel
Wood
Stone
Hollow Brick
Solid Brick
Hollow Core Plank
Concrete
Page
Bolt and Shield Anchors
Pin Anchors
Nail Anchors
Anchor Diameter
MECHAN I CAL
Base Material
•
•
• •
• •
• •
• •
•
• •
•
•
• • •
•
•
•
•
•
Zamac Hammer-Screw 28 •
• •
•
•
Zamac Nailin
28 •
• •
• •
•
Nylon Nailin
29 •
• •
• •
• • •
•
•
•
•
•
•
• •
•
•
•
•
•
•
• Suitable
May be Suitable
9
MECHANI CAL
POWER-STUD+ SD1 • POWER-STUD+ SD2
The Code Approved
Solution Leader
for Metal Deck Assembly Anchorage
4-1/2" W-Deck
Now has approvals for 3-7/8" profiles and anchorage into 2.5" topping slabs*
SAND-LIGHTWEIGHT CONCRETE
CONCRETE OR
OR NORMAL
NORMAL WEIGHT
WEIGHT CONCRETE
CONCRETE OVER
OVER STEEL
STEEL DECK
DECK
SAND-LIGHTWEIGHT
(MINIMUM 3,000
3,000 PSI)
PSI)
(MINIMUM
Upper Flute
Flute (Valley)
(Valley)
Upper
Max.
Max.
3"
"
3
Min.
Min. Edge
Edge
Distance
Distance
" (Typ.)
Min. 12-1/2
12-1/2"
(Typ.)
Min.
Lower Flute
Flute (Ridge)
(Ridge)
Lower
Flute Edge
Edge
Flute
CONCRETE OR
OR NORMAL
NORMAL WEIGHT
WEIGHT CONCRETE
CONCRETE OVER
OVER STEEL
STEEL DECK
DECK
SAND-LIGHTWEIGHT
(MINIMUM
(MINIMUM 3,000
3,000 PSI)
PSI)
3-7/8" W-Deck
Snake+
3-1/4"
3-1/4"
Top of
Deck
Minimum
Topping
Thickness
2-1/2"
®
®
Vertigo +
Powers ®
Wedge-Bolt +
3-1/4"
Upper
Flute
✔ ✔ ✔ ✔ ✔ ✔
Lower
Flute
✔ ✔ ✔ ✔ ✔ ✔
"
Min. 4-1/2
4-1/2"
Min.
(Typ.)
(Typ.)
"
Min. 4-1/2
4-1/2"
Min.
(Typ)
(Typ)
Upper Flute
Flute (Valley)
(Valley)
Upper
Max.
Max.
"
3"
3
Min. 3-7/8"
3-7/8"
Min.
(Typ.)
(Typ.)
Min. 3-7/8"
3-7/8"
Min.
(Typ.)
(Typ.)
Min. Edge
Edge
Min.
Distance
Distance
Lower Flute
Flute (Ridge)
(Ridge)
Lower
Flute
Flute Edge
Edge
CONCRETE OR
OR NORMAL
NORMAL WEIGHT
WEIGHT CONCRETE
CONCRETE OVER
OVER STEEL
STEEL DECK
DECK
SAND-LIGHTWEIGHT
(MINIMUM 3,000
3,000 PSI)
PSI)
(MINIMUM
Upper
Upper Flute
Flute (Valley)
(Valley)
B DECK
Bang-It ™
®
®
Cast In Place Power-Stud + Power-Stud +
Insert
SD1
SD2
1-1/2
1-1/2"
"
Max.
Max.
2-1/2"
2-1/2"
Min.
Min.
Max.
Max.
3-1/2"
3-1/2"
(Typ)
(Typ)
Min. Edge
Edge
Min.
Distance
Distance
Lower Flute
Flute Edge
Edge
Lower
1-3/4"
1-3/4"
Min.
Min.
Top of
Deck
2-1/2"
Minimum
Topping
Thickness
Upper
Flute
✔
✔
Lower
Flute
✔
✔
Top of
Deck
Minimum
Topping
Thickness
2-1/2"
Upper
Flute
✔ ✔ ✔
✔
Lower
Flute
✔ ✔ ✔
✔
* See individual ICC-ES Reports for details on each condition
Powers 7th Edition Technical
Manual is now available!
Please contact your local Powers Field
Engineer at 800-524-3244 to schedule a Lunch
& Learn and receive your new Tech Manual.
ESR-3657 ESR-2818 ESR-2502 ESR-2272 ESR-2526 ESR-2526
D R I V E N
E N G I N E E R E D
THE CONCRETE SOLUTION
™
10
Table Continues On Page 13
Bang-It™
✔
File No. EX1289
Also UL listed
and recognized
for use in
air handling
spaces
WoodKnocker™
✔
File No. EX1289
Also UL listed
and recognized
for use in
air handling
spaces
PowerStud+® SD2
✔
✔
File No.
EX1289
Wood
Vertigo™
✔
File No.
EX1289
Smart
DI+®
Hanger
Mate+
✔
File No.
EX1289 (N)
✔
File No. J.I.
3015153
File No. J.I.
3015153
ESR-3657
ESR-3657
ESR-2502
ESR-2272
ESR-2526
Cracked &
Uncracked
Concrete
Cracked &
Uncracked
Concrete
✔
✔
✔
✔
✔
✔*
for Steel Deck
in Cracked &
Uncracked
Concrete
✔
for Steel Deck
in Cracked &
Uncracked
Concrete
Cracked &
Uncracked
Concrete
File No.
3038104
✔
Pipe hanger
components
for automatic
sprinkler
systems
File No.
3038104
Cracked &
Uncracked
Concrete
✔
File No.
3015153
✔
File No.
3015153
✔
File No.
3042006
✔*
File No. Pending
ESR*
LIF
I
I C AT
O
QU
N
N
SE
IC REG
IO
I
Steel
Vertigo™
File No.
3033795,
3/8" and 1/2"
diameter
pipe hanger
components
for automatic
sprinkler
systems
✔
A
Vertigo™+
File No.
EX1289
✔
SM
Snake+™
MECHAN I CAL
Fire Sprinkler
Anchoring Solutions
Coming
Soon!
Improved
Thread
Design.
Contact
Powers
for more
details.
Bang-It™
Cast-in-Place
Insert
for Concrete
Over Steel
Deck
WoodKnocker™
PowerStud+® SD2
Cast-in-Place
Insert for
Wood Forms
Wedge
Expansion
Anchor
for Concrete
Snake+™
Vertigo™+
Internally
Threaded
Self Tapping
Anchor for
Threaded Rod
Rod Hanging
System
for Concrete
Steel
Vertigo™
Wood
Vertigo™
Smart
DI+®
Hanger
Mate+
Rod Hanging
System
for Steel
Base Material
Rod Hanging
System
for Wood
Base Material
Drop-In
Rod Hanging
System
for Concrete
1/4" Thread
Profile vs. 3/8"
* Pending
POWERS SUBMITTAL
GENERATOR
D R I V E N
E N G I N E E R E D
™
11
MECHANI CAL
SELECTION GUIDE
Masonry Solutions
OWER
RY
T
O
TES
LA
BORA
Pure110+
®
PowerStud+®
SD1
PowerStud+®
SD4/SD6
WedgeBolt+
Lok-Bolt
AS®
Tapper+®
Hollow
Set
ToggleBolt
StrapToggle
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
S
P
AC100+
Gold®
T
Gas
Pins
Powder
Pins
✔ ✔
ESR-3200
ESR-2966
ESR-1678
ESR-3196
ESR-3275
✔
✔
✔
✔
✔
IC REG
I C AT
I
OWER
RY
T
LA
O
TES
✔ ✔
S
P
LIF
O
QU
A
N
N
SE
SM
IO
I
Grouted
CMU
BORA
T
✔ ✔ ✔ ✔ ✔ ✔ ✔
ESR-3200
ESR-3275
✔
✔
IC REG
OWER
T
LA
O
TES
RY
P
I C AT
S
BRICK
LIF
I
O
QU
A
N
N
SE
SM
IO
I
UNGrouted
CMU
BORA
T
✔
AC100+
Gold®
✔ ✔ ✔ ✔
Pure110+®
PowerStud+®
SD1
PowerStud+®
SD4/SD6
Powers 7th Edition
Technical Manual is
now available!
Please contact your local Powers Field
Engineer at 800-524-3244 to schedule
a Lunch & Learn and receive your new
Tech Manual.
12
WedgeBolt+
Lok-Bolt
AS®
Tapper+®
Hollow
Set
D R I V E N
ToggleBolt
StrapToggle
Gas
Pins
Powder
Pins
E N G I N E E R E D
™
PB+ • PB-PRO • POWERBOLT
MECHAN I CAL
New!
Powers PB-Pro
Code listed
Heavy-Duty Sleeve Anchor – Metric
ICC-ES ESR-3260
Base Material
cracked concrete
Concrete
PB+ (Power-Bolt®+)
Size Range
24mm x 148mm to 28mm x 220mm
Heavy-Duty Sleeve Anchor
Anchor Material
Carbon Steel
Base Material
Concrete
The PB-Pro is a large diameter torque controlled, heavy duty sleeve anchor
suitable for concrete applications. It is available in carbon steel with a finished
hex head.
Size Range
1/4" x 1-3/4" to 3/4" x 8-1/4"
Anchor Material
Carbon Steel
The PB+ anchor is a torque controlled, heavy duty sleeve style anchor which is
designed for consistent performance in cracked and uncracked concrete. It is
available with a finished hex head.
Carbon steel PB+ anchors are manufactured using a Grade 8 bolt. They are
plated with a commercial bright zinc finish and have a supplementary chromate
treatment in accordance with ASTM B 633.
Carbon Steel Hex Head PB-Pro
Cat. No.
Size
PFM1220650
PFM1220700
PFM1220750
PFM1220800
PFM1220850
24-M16 x 148mm
24-M16 x 178mm
28-M20 x 170mm
28-M20 x 190mm
28-M20 x 220mm
Drill Dia.
Length
Std. Box
Std. Ctn.
24mm
24mm
28mm
28mm
28mm
148mm
178mm
170mm
190mm
220mm
5
5
5
5
5
20
20
15
10
10
Carbon Steel Hex Head PB+
Cat. No.
Size
6902SD
6906SD
6911SD
6910SD
6913SD
6914SD
6916SD
6930SD*
6932SD
6934SD
6936SD
6940SD*
6942SD
6944SD
6945SD
6947SD
6950SD
6952SD
6954SD
6956SD
6958SD
1/4" x 1-3/4"
1/4" x 3"
3/8" x 1-7/8"
3/8" x 2-1/4"
3/8" x 3"
3/8" x 3-1/2"
3/8" x 4"
1/2" x 2-3/4"
1/2" x 3-1/2"
1/2" x 4-3/4"
1/2" x 5-3/4"
5/8" x 3"
5/8" x 4"
5/8" x 5"
5/8" x 6"
5/8" x 8-1/2"
3/4" x 3-1/4"
3/4" x 4-1/4"
3/4" x 5-1/4"
3/4" x 7-1/4"
3/4" x 8-1/4"
Drill Dia.
Std. Box
Std. Ctn.
1/4"
1/4"
3/8"
3/8"
3/8"
3/8"
3/8"
1/2"
1/2"
1/2"
1/2"
5/8"
5/8"
5/8"
5/8"
5/8"
1/4"
3/4"
3/4"
3/4"
3/4"
100
100
50
50
50
50
50
50
50
25
25
20
15
15
15
10
15
10
10
10
10
600
600
300
300
300
300
300
200
200
200
150
150
120
90
90
40
90
60
60
40
40
*Asterisked catalog numbers denote sizes which are less than the minimum standard anchor length for
strength design or not included in ESR-3260. The published size includes the diameter and the length which
is measured from below the washer to the end of the anchor.
SDS-Max Carbide Drill Bits - 4 Cutter
Cat. No.
Size
PPA1330220
PPA1330290
24 mm x 340 mm
28 mm x 380 mm
Drill Dia.
24mm
28mm
Length usable length
340mm
380mm
Std. tube
200mm
250mm
1
1
Power-Bolt®
Heavy-Duty Sleeve Anchor
Base Material
Concrete, Block, Brick, Stone
Size Range
1/4" x 5/8" to 1/4" x 5-1/2"
Anchor Material
Type 304 Stainless Steel & Carbon Steel (Flat Head)
The Power-Bolt anchor is a heavy duty sleeve style anchor which is vibration
resistant and removable. It is available with a finished hex head or flat head with
a hex key insert and can be used in concrete, block, brick, or stone.
Stainless steel Power-Bolt anchors are manufactured from 300 series stainless
steel (passivated).
304 stainless steel hex head Power-Bolt
Cat. No.
Size
5902
5906
5910
5914
5916
5930
5934
1/4" x 1-3/4"
1/4" x 3"
3/8" x 2-1/4"
3/8" x 3-1/2"
3/8" x 4"
1/2" x 2-3/4"
1/2" x 4-3/4"
Drill Dia.
Min. Depth
Std. Box
Std. Ctn.
1/4"
1/4"
3/8"
3/8"
3/8"
1/2"
1/2"
1-1/4"
1-1/4"
2"
2"
2"
2-1/2"
2-1/2"
100
100
50
50
50
50
25
600
600
300
300
300
200
150
13
MECHANI CAL
POWER-STUD+ SD1 • POWER-STUD+ SD2
Carbon Steel Flat Head Power-Bolt®
Flat Head Carbon steel Power-Bolt anchors are manufactured using a Grade 5
bolt. They are plated with a commercial bright zinc finish and have a supplementary chromate treatment in accordance with ASTM Specification B 633.
The flat head Power-Bolt anchor has a hex key insert formed in the head of the
bolt. Each box contains an Allen wrench which matches the insert size.
Cat. No.
Size
6981
6982
6983
6984
6987
3/8" x 3-3/4"
3/8" x 5"
3/8" x 6"
1/2" x 5"
5/8" x 5-1/2"
Drill Dia.
Min. Depth
Std. Box
Std. Ctn.
3/8"
3/8"
3/8"
1/2"
5/8"
2"
2"
2"
2-1/2"
2-3/4"
50
50
50
25
15
300
300
300
150
90
The published length is the overall length of the anchor.
Cat. No.
size
Thread Length
Std. Box
Std. Ctn.
7432SD1
7433SD1
7434SD1
7436SD1
7438SD1
7439SD1
7440SD1*
7441SD1*
7442SD1
7444SD1
7446SD1
7448SD1
7449SD1
7451SD1
7450SD1*
7452SD1
7454SD1
7461SD1*
7463SD1
7465SD1
7473SD1
5/8" x 4-1/2"
5/8" x 5"
5/8" x 6"
5/8" x 7"
5/8" x 8-1/2"
5/8" x 10"
3/4" x 4-1/4"
3/4" x 4-3/4"
3/4" x 5-1/2"
3/4" x 6-1/4"
3/4" x 7"
3/4" x 8-1/2"
3/4" x 10"
3/4" x 12"
7/8" x 6"
7/8" x 8"
7/8" x 10"
1" x 6"
1" x 9"
1" x 12"
1-1/4" x 9"
2-1/2"
3"
4"
5"
6-1/2"
8"
1-3/4"
2-1/4"
3"
3-3/4"
4-1/2"
6"
7-1/2"
9-1/2"
2-3/4"
4-3/4"
6-3/4"
2-3/8"
5-3/8"
8-3/8"
4-3/4"
25
25
25
25
25
25
20
20
20
20
20
10
10
10
10
10
10
10
10
5
5
100
100
75
75
50
50
60
60
60
60
20
60
40
40
40
40
40
30
30
20
15
7475SD1
1-1/4" x 12"
7-3/4"
5
15
* Sizes which are less than the minimum standard anchor length for strength design. The published length is
the overall length of the anchor. Allow for fixture thickness plus one anchor diameter for the nut and washer
thickness when selecting a length. All anchors are packaged with nuts and washers.
Code listed
Code listed
cracked concrete
Masonry
ICC-ES ESR-2818
city of los angeles
LARR-25787 (Concrete)
ICC-ES ESR-2966
Tie-Wire Power-Stud
Cat. No.
Size
7409SD1
1/4" x 2"
Tie-Wire Hole Size
Min. Embed.
Std. Box
Std. Ctn.
9/32"
1-1/8"
100
500
city of los angeles
LARR-25864 (Masonry)
Power-Stud®+ SD1
Wedge Type Expansion Anchor
Base Material
Normal-Weight Concrete, Sand-Lightweight Concrete, Concrete over Metal Deck,
Grout-Filled Masonry
Size Range
Code listed
1/4" diameter, 3/8" diameter through 1-1/4" diameter (cracked and
uncracked concrete)
ICC-ES ESR-2502
Anchor Material
cracked concrete
Zinc Plated Carbon Steel Body and Expansion Clip, with Nut and Washer
The Power-Stud+ SD1 anchor is a fully threaded, torque-controlled, wedge
expansion anchor which is designed for consistent performance in cracked and
uncracked concrete. Suitable base materials include normal-weight concrete,
structural sand-lightweight concrete and concrete over metal deck. The anchor is
manufactured with a zinc plated carbon steel body and expansion clip.
Power-Stud®+ SD2
Patented & Additional Patents Pending
Size Range
Cat. No.
size
7400SD1*
7402SD1
7404SD1
7410SD1*
7412SD1*
7413SD1
7414SD1
7415SD1
7416SD1
7417SD1
7420SD1*
7422SD1
7423SD1
7424SD1
7426SD1
7427SD1
7428SD1
7430SD1*
1/4" x 1-3/4"
1/4" x 2-1/4"
1/4" x 3-1/4"
3/8" x 2-1/4"
3/8" x 2-3/4"
3/8" x 3"
3/8" x 3-1/2"
3/8" x 3-3/4"
3/8" x 5"
3/8" x 7"
1/2" x 2-3/4"
1/2" x 3-3/4"
1/2" x 4-1/2"
1/2" x 5-1/2"
1/2" x 7"
1/2" x 8-1/2"
1/2" x 10"
5/8" x 3-1/2"
Base Material
Normal-Weight Concrete, Sand-Lightweight Concrete, Concrete over Metal Deck,
Grout-Filled Masonry
3/8" through 3/4" diameter (Cracked and Uncracked Concrete)
Power-Stud+ SD1 Carbon Steel Body & Expansion Clip
14
city of los angeles
LARR-25831(Concrete)
Thread Length
Std. Box
Std. Ctn.
3/4"
1-1/4"
2-1/4"
7/8"
1-3/8"
1-5/8"
2-1/8"
2-3/8"
3-5/8"
5-5/8"
1"
2"
2-3/4"
3-3/4"
5-1/4"
6-3/4"
8-1/4"
1-1/2"
100
100
100
50
50
50
50
50
50
50
50
50
50
50
25
25
25
25
600
600
600
300
300
300
300
300
300
200
200
200
200
150
100
100
100
100
Anchor Material
Zinc Plated Carbon Steel Body with Stainless Steel Expansion Clip
The Power-Stud+ SD2 anchor is a fully threaded, torque-controlled, wedge
expansion anchor which is designed for consistent performance in cracked and
uncracked concrete. Suitable base materials include normal-weight concrete,
structural sand-lightweight concrete and concrete over metal deck. The anchor is
manufactured with a zinc plated carbon steel body and stainless steel expansion
clip for premium performance.
Patented & Additional Patents Pending
Power-Stud+ SD2 Carbon Steel Body & ss Expansion Clip
Cat. No.
Size
7413SD2
7414SD2
7415SD2
7416SD2
7422SD2
7423SD2
7424SD2
3/8" x 3"
3/8" x 3-1/2"
3/8" x 3-3/4"
3/8" x 5"
1/2" x 3-3/4"
1/2" x 4-1/2"
1/2" x 5-1/2"
Thread Length
Std. Box
Std. Ctn.
1-5/8"
2-1/4"
2-1/2"
3-3/4"
2-1/8"
2-7/8"
3-7/8"
50
50
50
50
50
50
50
300
300
300
300
200
200
150
POWER-STUD+ SD4 + SD6 • POWER-STUD HD5
Cat. No.
size
7426SD2
7427SD2
7435SD2
7433SD2
7434SD2
7436SD2
7438SD2
7442SD2
7444SD2
7446SD2
7448SD2
1/2" x 7"
1/2" x 8-1/2"
5/8" x 4-3/4"
5/8" x 5"
5/8" x 6"
5/8" x 7"
5/8" x 8-1/2"
3/4" x 5-1/2"
3/4" x 6-1/4"
3/4" x 7"
3/4" x 8-1/2"
Thread Length
Std. Box
Std. Ctn.
5-3/8"
6-7/8"
2-7/8"
3-1/8"
4-1/8"
5-1/8"
6-5/8"
3-1/4"
4"
4-3/4"
6-1/4"
25
25
25
25
25
25
25
20
20
20
10
100
100
100
100
75
75
75
60
60
60
60
The published length is the overall length of the anchor. Allow for fixture thickness plus one anchor diameter for
the nut and washer thickness when selecting a length. All anchors are packaged with nuts and washers.
Installation Accessories for additional length
Cat. No.
Size
08465
Adjustable torque wrench with 1/2" square drive (10 to 150 ft.-lbs.)
Std. Box
1
Code listed
ICC-ES ESR-2502
cracked concrete
Power-Stud+® SD4 + SD6
Stainless Steel Wedge Type Expansion Anchor
Base Material
Size Range
1/4" through 3/4" diameter
Anchor Material
Stainless Steel Body with Expansion Clip with Nut and Washer
The Power-Stud+ SD4 and Power-Stud+ SD6 anchors are fully threaded, torquecontrolled, stainless steel wedge expansion anchors which are designed for consistent performance in cracked and uncracked concrete. Suitable base materials
are normal-weight and sand-lightweight concrete. The anchor is manufactured
with a stainless steel body and expansion clip. Nut and washer are included.
Power-Stud+ SD4 (304 SS)
size
7300SD4*
7302SD4
7304SD4
7310SD4*†
7312SD4 †
7313SD4
7314SD4 †
7315SD4
7316SD4
7317SD4 †
7320SD4* †
7322SD4
7323SD4
7324SD4
7326SD4
7330SD4* †
7332SD4 †
7333SD4
7334SD4
7336SD4 †
7338SD4
7340SD4* †
7341SD4* †
7342SD4
7344SD4 †
7346SD4 †
1/4" x 1-3/4"
1/4" x 2-1/4"
1/4" x 3-1/4"
3/8" x 2-1/4"
3/8" x 2-3/4"
3/8" x 3"
3/8" x 3-1/2"
3/8" x 3-3/4"
3/8" x 5"
3/8" x 7"
1/2" x 2-3/4"
1/2" x 3-3/4"
1/2" x 4-1/2"
1/2" x 5-1/2"
1/2" x 7"
5/8" x 3-1/2"
5/8" x 4-1/2"
5/8" x 5"
5/8" x 6"
5/8" x 7"
5/8" x 8-1/2"
3/4" X 4-1/4"
3/4" X 4-3/4"
3/4" X 5-1/2"
3/4" X 6-1/4"
3/4" X 7"
size
7348SD4
7349SD4
3/4" X 8-1/2"
3/4" X 10"
Thread Length
Std. Box
Std. Ctn.
6-1/8"
7-5/8"
10
10
40
40
Thread Length
Std. Box
Std. Ctn.
3/4"
1-1/4"
2-1/4"
7/8"
1-3/8"
1-5/8"
2-1/8"
2-3/8"
3-5/8"
5-5/8"
1"
2"
2-3/4"
3-3/4"
5-1/4"
1-1/2"
2-1/2"
3"
4"
5"
6-1/2"
1-7/8"
2-3/8"
3-1/8"
3-7/8"
4-5/8"
6-1/8"
100
100
100
50
50
50
50
50
50
50
50
50
50
50
25
25
25
25
25
25
25
20
20
20
20
20
10
600
600
600
300
300
300
300
300
300
300
300
300
300
300
100
100
100
100
75
75
50
60
60
60
60
60
40
† Discontinued item once current stock exhausted.
Power-Stud+ SD6 (316SS)
Cat. No.
size
7600SD6*
7602SD6
7604SD6
7610SD6*
7612SD6
7613SD6
7614SD6
7615SD6
7616SD6
7617SD6
7620SD6*
7622SD6
7623SD6
7624SD6
7626SD6
7630SD6*
7632SD6
7633SD6
7634SD6
7636SD6
7638SD6
7640SD6*
7641SD6*
7642SD6
7644SD6
7646SD6
7648SD6
1/4" x 1-3/4"
1/4" x 2-1/4"
1/4" x 3-1/4"
3/8" x 2-1/4"
3/8" x 2-3/4"
3/8" x 3"
3/8" x 3-1/2"
3/8" x 3-3/4"
3/8" x 5"
3/8" x 7"
1/2" x 2-3/4"
1/2" x 3-3/4"
1/2" x 4-1/2"
1/2" x 5-1/2"
1/2" x 7”
5/8" x 3-1/2"
5/8" x 4-1/2"
5/8" x 5"
5/8" x 6"
5/8" x 7"
5/8" x 8-1/2"
3/4" X 4-1/4"
3/4" X 4-3/4"
3/4" X 5-1/2"
3/4" X 6-1/4"
3/4" X 7"
3/4" X 8-1/2"
Power-Stud+ SD4 and Power-Stud+ SD6 anchors can be domestically manufactured (assembled in the USA
with foreign and domestic components) and are available for special order only. Call for details.
*Asterisked catalog numbers denote sizes which are less than the minimum standard anchor length for
strength design.
The published size includes the diameter and the overall length of the anchor. All anchors are packaged with
nuts and washers.
Normal-Weight Concrete, Sand-Lightweight Concrete
Cat. No.
Cat. No.
MECHAN I CAL
Power-Stud+ SD2 Carbon Steel Body & ss Expansion Clip, Continued
Thread Length
Std. Box
Std. Ctn.
3/4"
1-1/4"
2-1/4"
7/8"
1-3/8"
1-5/8"
2-1/8"
2-3/8"
3-5/8"
5-5/8"
1"
2"
2-3/4"
3-3/4"
5-1/4"
1-1/2"
2-1/2"
3"
4"
5"
6-1/2"
1-7/8"
2-3/8"
3-1/8"
3-7/8"
4-5/8"
100
100
100
50
50
50
50
50
50
50
50
50
50
50
25
25
25
25
25
25
25
20
20
20
20
20
600
600
600
300
300
300
300
300
300
300
300
300
300
300
100
100
100
100
75
75
50
60
60
60
60
60
Power-Stud® HD5
Base Material
Concrete, Grouted CMU
Size Range
3/8" x 3" to 3/4" x 8-1/2"
Anchor Material
Hot Dipped Galvanized Steel
The Power-Stud anchor is a one piece fully threaded, wedge style anchor available in carbon steel and stainless steel. The drill bit diameter needed for proper
installation is the same nominal size as the anchor diameter.
Hot Dipped Galvanized Power-Stud anchors are manufactured from carbon steel
which have a hot dipped galvanized coating (zinc) in accordance with ASTM A
153 Class C or D Specification.
hot dipped Galvanized Power-Stud
Cat. No.
Size
7713HD5
7715HD5
7716HD5
7717HD5
7720HD5
7722HD5
7723HD5
7724HD5
7726HD5
7730HD5
7733HD5
3/8" x 3"
3/8" x 3-3/4"
3/8" x 5"
3/8" x 7"
1/2" x 2-3/4"
1/2" x 3-3/4"
1/2" x 4-1/2"
1/2" x 5-1/2"
1/2" x 7"
5/8" x 3-1/2"
5/8" x 5"
Min. Embed.
Thread Length
Std. Box
Std. Ctn.
1-1/2"
1-1/2"
1-1/2"
1-1/2"
2"
2"
2"
2"
2"
2-3/8"
2-3/8"
1-1/2"
2-3/8"
3-1/2"
5-1/2"
1"
2"
2-3/4"
3-3/4"
5-1/4"
1-1/2"
3"
50
50
50
50
50
50
50
50
50
25
25
300
300
300
200
200
200
200
200
150
100
100
Table Continues On Next Page
15
MECHANI CAL
POWER-STUD • ATOMIC+ UNDERCUT
Cat. No.
Size
7734HD5
7738HD5
7741HD5
7742HD5
7746HD5
7748HD5
5/8" x 6"
5/8" x 8-1/2"
3/4" x 4-3/4"
3/4" x 5-1/2"
3/4" x 7"
3/4" x 8-1/2"
Min. Embed.
Thread Length
Std. Box
Std. Ctn.
2-3/8"
2-3/8"
3-3/8"
3-3/8"
3-3/8"
3-3/8"
4"
6-1/2"
2-1/4"
3"
4-1/2"
6"
25
25
20
20
20
10
100
75
60
60
60
40
Power-Stud®
Base Material
Concrete, Grouted CMU
Size Range
1/4" x 1-3/4" to 1-1/4" x 12"
Anchor Material
Carbon Steel, Type 304 or 316 Stainless Steel
The Power-Stud anchor is a one piece fully threaded, wedge style anchor
available in carbon steel and stainless steel. The threaded Rod Hanger version
is designed for use in solid concrete. The drill bit diameter needed for proper
installation is the same nominal size as the anchor diameter.
Rod Hanger Power-Stud
Cat. No.
Rod Size
Anchor Size
7806
3/8"
1/2"x 2-3/8"
Drill Dia.
Min. Embed.
1/2"
2-1/4"
Thread Depth Std. Box
9/16"
50
STD. CTN.
250
Type 316 Stainless Steel Power-Stud
Cat. No.
Size
7600
7602
7604
7610
7612
7613
7614
7615
7616
7620
7622
7623
7624
7626
7630
7632
7633
7634
7636
7638
7640
7641
7642
7644
7646
7648
1/4" x 1-3/4"
1/4" x 2-1/4"
1/4" x 3-1/4"
3/8" x 2-1/4"
3/8" x 2-3/4"
3/8" x 3"
3/8" x 3-1/2"
3/8" x 3-3/4"
3/8" x 5"
1/2" x 2-3/4"
1/2" x 3-3/4"
1/2" x 4-1/2"
1/2" x 5-1/2"
1/2" x 7"
5/8" x 3-1/2"
5/8" x 4-1/2"
5/8" x 5"
5/8" x 6"
5/8" x 7"
5/8" x 8-1/2"
3/4" x 4-1/4"
3/4" x 4-3/4"
3/4" x 5-1/2"
3/4" x 6-1/4"
3/4" x 7"
3/4" x 8-1/2"
Min. Embed. Thread Length
1-1/8"
1-1/8"
1-1/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
2-1/4"
2-1/4"
2-1/4"
2-1/4"
2-1/4"
2-3/4"
2-3/4"
2-3/4"
2-3/4"
2-3/4"
2-3/4"
3-3/8"
3-3/8"
3-3/8"
3-3/8"
3-3/8"
3-3/8"
3/4"
1-1/4"
2-1/4"
1-1/4"
1-5/8"
1-7/8"
2-3/8"
2-5/8"
3-7/8"
1-3/8"
2-3/8"
3-1/8"
4-1/8"
5-5/8"
2"
3"
3-1/2"
4-1/2"
5-1/2"
7"
2-3/8"
2-7/8"
3-5/8"
4-3/8"
5-1/8"
6-5/8"
Std. Box
Std. Ctn.
100
100
100
50
50
50
50
50
50
50
50
50
50
25
25
25
25
25
25
25
20
20
20
20
20
10
500
500
500
250
250
250
250
250
250
200
200
200
150
100
100
100
100
75
75
75
60
60
60
60
60
40
The published length is the overall length of the anchor. Allow for fixture thickness plus one anchor diameter
for the nut and washer thickness when selecting a length.
Stainless Steel Power-Stud anchors are manufactured from AISI Type 304 /
304 Cu and Type 316 stainless steel which is passivated.
Type 304 Stainless Steel Power-Stud
Cat. No
Size
7300
7302
7304
7310
7312
7313
7314
7315
7316
7320
7322
7323
7324
7326
7330
7332
7333
7334
7336
7338
7340
7341
7342
7344
7346
7348
7349
7352
7361
7363
7365
1/4" x 1-3/4"
1/4" x 2-1/4"
1/4" x 3-1/4"
3/8" x 2-1/4"
3/8" x 2-3/4"
3/8" x 3"
3/8" x 3-1/2"
3/8" x 3-3/4"
3/8" x 5"
1/2" x 2-3/4"
1/2" x 3-3/4"
1/2" x 4-1/2"
1/2" x 5-1/2"
1/2" x 7"
5/8" x 3-1/2"
5/8" x 4-1/2"
5/8" x 5"
5/8" x 6"
5/8" x 7"
5/8" x 8-1/2"
3/4" x 4-1/4"
3/4" x 4-3/4"
3/4" x 5-1/2"
3/4" x 6-1/4"
3/4" x 7"
3/4" x 8-1/2"
3/4" x 10"
7/8" x 8"
1" x 6"
1" x 9"
1" x 12"
Min. Embed.
Thread Length
Std. Box
Std. Ctn.
1-1/8"
1-1/8"
1-1/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
2-1/4"
2-1/4"
2-1/4"
2-1/4"
2-1/4"
2-3/4"
2-3/4"
2-3/4"
2-3/4"
2-3/4"
2-3/4"
3-3/8"
3-3/8"
3-3/8"
3-3/8"
3-3/8"
3-3/8"
3-3/8"
3-7/8"
4-1/2"
4-1/2"
4-1/2"
3/4"
1-1/4"
2-1/4"
1-1/4"
1-5/8"
1-7/8"
2-3/8"
2-5/8"
3-1/8"
1-3/8"
2-3/8"
3-1/8"
4-1/8"
5-5/8"
2"
3"
3-1/2"
4-1/2"
5-1/2"
7"
2-3/8"
2-7/8"
3-5/8"
4-3/8"
5-1/8"
6-5/8"
8-1/8"
4-3/4"
2-3/8"
5-3/8"
8-3/8"
100
100
100
50
50
50
50
50
50
50
50
50
50
25
25
25
25
25
25
25
20
20
20
20
20
10
10
10
10
10
5
500
500
500
250
250
250
250
250
250
200
200
200
150
100
100
100
100
75
75
75
60
60
60
60
60
40
30
40
30
30
15
The published length is the overall length of the anchor. Allow for fixture thickness plus one anchor diameter
for the nut and washer thickness when selecting a length.
16
Atomic+ Undercut
®
Heavy Duty Undercut Anchor
Code listed
ESR-3067
ICC-ES
cracked concrete
Base Material
Normal-Weight Concrete, Sand-Lightweight Concrete
Size Range
3/8" diameter through 3/4" diameter
Anchor Material
Zinc Plated A 36 Carbon Steel, Zinc Plated High Strength A 193 Grade B7 Steel,
The Atomic+ Undercut anchor is a heavy duty undercut anchor which is designed for consistent performance in cracked and uncracked concrete. Atomic+
Undercut anchors are available for standard installations and for through bolt
applications where the fixture is already in place. The Atomic+ Undercut anchor
is installed into a pre-drilled hole which has been enlarged at the bottom in
the shape of a reversed cone using the Powers Undercut Drill Bit. The result is
an anchor which transfers load mainly through bearing, and unlike a typical
expansion anchor is not dependent upon friction between the expansion sleeve
and the concrete.
*Contact Powers Fasteners for appropriate drilling method. For anchor lengths not listed please contact
Powers Fasteners. For availability of all anchor lengths please contact Powers Fasteners.
ATOMIC+ UNDERCUT ANCHOR A 36 STEEL
CAt. NO.
NOM. ANCHOR DIA.
03100SD
03102SD
03108SD
03110SD
03120SD
03122SD
03132SD
03134SD
3/8"
3/8"
1/2"
1/2"
5/8"
5/8"
3/4"
3/4"
length
5-1/2"
5-1/2"
7"
7"
7-3/4"
7-3/4"
8-5/8"
8-5/8"
Req. undercut bit
(cat. No.)
recommended
stop bit (cat. No.)
ANCHOR TYPE
03200SD
03200SD
03201SD
03201SD
03202SD
03202SD
03203SD
03203SD
03220SD
*
03222SD
*
03222SD
*
03228SD
*
Standard
Through bolt
Standard
Through bolt
Standard
Through bolt
Standard
Through bolt
STD. BOX
20
20
15
15
10
10
8
8
LOK-Bolt AS
Cat. No.
Nom.
Anchor Dia.
03104SD
03106SD
03112SD
03114SD
03116SD
03118SD
03124SD
03126SD
03128SD
03130SD
03136SD
03138SD
3/8"
3/8"
1/2"
1/2"
1/2"
1/2"
5/8"
5/8"
5/8"
5/8"
3/4"
3/4"
Length
6-3/4"
6-3/4"
8"
8"
9-3/4"
9-3/4"
10-3/4"
10-3/4"
12-1/4"
12-1/4"
13-5/8"
13-5/8"
Req. Undercut Bit
(Cat. No.)
Recommended
Stop Bit (Cat. No.)
Anchor
Type
Std. Box
03200SD
03200SD
03201SD
03201SD
03201SD
03201SD
03202SD
03202SD
03202SD
03202SD
03203SD
03203SD
03221SD
*
03223SD
*
03224SD
*
03226SD
*
03227SD
*
03229SD
*
Standard
Through bolt
Standard
Through bolt
Standard
Through bolt
Standard
Through bolt
Standard
Through bolt
Standard
Through bolt
20
20
15
15
15
15
10
10
10
10
8
8
Setting Sleeve
Cat. NO.
CORRESPONDING NOMinal ANCHOR DIA.
03210SD
03211SD
03218SD
03213SD
3/8"
1/2"
5/8"
3/4"
STD. TUBE
1
1
1
1
MECHAN I CAL
ATOMIC+ UNDERCUT High Strength A 193, Grade B7 Steel
Cutter blade replacements for undercut bit
Cat. NO.
Description
03205SD
03206SD
03208SD
03209SD
Atomic+ (3/8") Cutter Blade - 5/8"
Atomic+ (1/2") Cutter Blade - 3/4"
Atomic+ (5/8") Cutter Blade - 1"
Atomic+ (3/4") Cutter Blade - 1-1/8"
STD. TUBE
1
1
1
1
replacement bow jaws for undercut bit
Atomic undercut+ Type 316 Stainless Steel
Cat.
No.
Nom.
Anchor Dia.
03600SD
03602SD
03608SD
03610SD
03620SD
03622SD
03632SD
03634SD
3/8"
3/8"
1/2"
1/2"
5/8"
5/8"
3/4"
3/4"
Undercut Bit
Length Req. (Cat.
No.)
5-1/2"
5-1/2"
7"
7"
7-3/4"
7-3/4"
8-5/8"
8-5/8"
03200SD
03200SD
03201SD
03201SD
03202SD
03202SD
03203SD
03203SD
Recommended
Stop Bit (Cat. No.)
Anchor
Type
Std.
Box
03220SD
*
03222SD
*
03225SD
*
03228SD
*
Standard
Through bolt
Standard
Through bolt
Standard
Through bolt
Standard
Through bolt
20
20
15
15
10
10
8
8
Cat. NO.
Description
03212SD
03215SD
03216SD
03217SD
3/8" Bow Jaw for 5/8" Hole
1/2" Bow Jaw for 3/4" Hole
5/8" Bow Jaw for 1" Hole
3/4" Bow Jaw for 1-1/8" Hole
STD. TUBE
1
1
1
1
Lok-Bolt AS®
Sleeve Type Expansion Anchor
Base Material
Concrete, Block, Brick
Size Range
1/4" x 5/8" to 3/4" x 7-1/2"
Anchor Material
Carbon Steel & Stainless Steel
The Stop Drill Bit creates a drill hole to the proper depth for standard installations of the Atomic+ Undercut anchor (For through bolt applications please
contact Powers Fasteners for appropriate drilling method)
Stop Drill Bits
Cat.
NO.
03220SD
03221SD
03222SD
03223SD
03224SD
03225SD
03226SD
03227SD
03228SD
03229SD
NOMinal
STOP DRILL Bit Dia.
CORRESPONDING
Nominal Anchor Dia.
MAX.
DRILL Depth
SHANK
TYPE
STD.
TUBE
5/8"
5/8"
3/4"
3/4"
3/4"
1"
1"
1"
1-1/8"
1-1/8"
3/8"
3/8"
1/2"
1/2"
1/2"
5/8"
5/8"
5/8"
3/4"
3/4"
3-1/8"
4-3/8"
4-1/4"
5-1/4"
7"
5"
8"
9-1/2"
5-13/16"
10-13/16"
SDS
SDS
SDS
SDS
SDS
SDS-Max
SDS-Max
SDS-Max
SDS-Max
SDS-Max
1
1
1
1
1
1
1
1
1
1
The Undercut Drill Bits unique design enlarges the bottom of the drill hole creating a reverse cone sized to receive the Atomic+ Undercut anchor.
Undercut Drill Bits
Cat.
NO.
03200SD
03201SD
03202SD
03203SD
NOMinal
STOP DRILL Bit Dia.
CORRESPONDING
Nominal Anchor Dia.
MAX.
DRILL Depth
SHANK
TYPE
STD.
TUBE
5/8"
3/4"
1"
1-1/8"
3/8"
1/2"
5/8"
3/4"
9"
10-1/4"
12-1/4"
13-1/2"
SDS
SDS
SDS-Max
SDS-Max
1
1
1
1
The Lok-Bolt AS anchor is a pre-assembled single unit sleeve anchor available in
carbon steel and stainless steel which can be used in concrete, block, brick and
stone. Extension sleeves are added to create longer lengths.
* AS refers to all-steel sleeve
Hex Nut LoK-Bolt AS CARBON STEEL
Cat. No.
Size
5005S
5010S
5015S
5020S
5022S
5025S
5030S
5034S
5033S
5032S
5035S
5038S
5040S
5045S
5050S
5055S
5060S
5065S
5/16" x 1-1/2"
5/16" x 2-3/8"
3/8" x 1-7/8"
3/8" x 3"
3/8" x 4"
1/2" x 2-1/2"
1/2" x 3"
1/2" x 3-3/4"
1/2" x 5-1/4"
1/2" x 6"
5/8" x 2-1/2"
5/8" x 3"
5/8" x 4-1/4"
5/8" x 5-3/4"
3/4" x 2-3/4"
3/4" x 4-1/4"
3/4" x 6-1/4"
3/4" x 8-1/4"
Drill Dia.
Min. Embed.
Std. Box
Std. Ctn.
5/16"
5/16"
3/8"
3/8"
3/8"
1/2"
1/2"
1/2"
1/2"
1/2"
5/8"
5/8"
5/8"
5/8"
3/4"
3/4"
3/4"
3/4"
1"
1"
1-1/4"
1-1/4"
1-1/4"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
2"
2"
2"
2"
2-1/4"
2-1/4"
2-1/4"
2-1/4"
100
100
50
50
50
25
25
25
25
10
25
25
10
10
10
10
10
10
1000
500
500
500
250
250
250
125
125
100
125
125
100
100
100
40
30
30
The published length is measured from below the washer to the end of the anchor.
17
MECHANI CAL
LOK-BOLT AS • SET-BOLT
Threshold Flat Head LoK-Bolt AS
Hex Nut LoK-Bolt AS 304 STAINLESS STEEL
Cat. No.
Size
6152S
6153S
6156S
6157S
6160S
6164S
3/8" x 1-7/8"
3/8" x 3"
1/2" x 2-1/2"
1/2" x 3"
1/2" x 3-3/4"
5/8" x 4-1/4"
Drill Dia.
Min. Embed
Std. Box
Std. Ctn.
3/8"
3/8"
1/2"
1/2"
1/2"
5/8"
1-1/4"
1-1/4"
1-1/2"
1-1/2"
1-1/2"
2"
50
50
25
25
25
10
500
500
250
250
125
100
Cat. No.
Size
5500S
1/4" x 2"
Drill Dia.
Min. Depth
Std. Box
Std. Ctn.
1/4"
1/2"
100
1000
Drill Dia.
Min. Depth
Std. Box
Std. Ctn.
5/16"
3/8"
1/2"
1/2"
1-1/4"
1-1/2"
50
50
25
250
250
125
Drill Dia.
Min. Depth
Std. Box
Std. Ctn.
5/16"
1"
100
1000
Drill Dia.
Std. Box
Std. Ctn.
3/8"
50
500
This part does not have a compression ring.
Rod Hanger LoK-Bolt AS CARBON STEEL
Cat. No.
Size
5810S
5815S
5825S
1/4" x 1-1/2"
3/8" x 1-7/8"
1/2" x 2-1/4"
Acorn Nut LoK-Bolt AS CARBON STEEL
Cat. No.
Size
5125S
5150S
5175S
1/4" x 5/8"
1/4" x 1-3/8"
1/4" x 2-1/4"
Drill Dia.
Min. Embed.
Std. Box
Std. Ctn.
1/4"
1/4"
1/4"
1/2"
1/2"
1/2"
100
100
100
1000
1000
1000
Tie-Wire LoK-Bolt AS
Acorn Nut LoK-Bolt AS 304 STAINLESS STEEL
Cat. No.
size
6150S
1/4" x 1-3/8"
Drill dia.
Min. Embed.
Std. box
Std. Ctn.
1/4"
1/2"
100
1000
Cat. No.
Size
5700S
5/16" x 1-1/2"
LoK-Bolt AS Extenders CARBON STEEL (for additional length)
Cat. No.
Size
5684
3/8" x 1-1/4"
Round Head LoK-Bolt AS CARBON STEEL
Cat. No.
Size
5205S
5210S
5215S
5220S
5225S
5230S
5235S
5240S
1/4" x 1-3/8"
1/4" x 2-1/4"
1/4" x 3"
1/4" x 3-3/4"
5/16" x 2-3/8"
5/16" x 3-3/8"
3/8" x 2-3/4"
3/8" x 3-3/4"
Drill Dia.
Min. Embed.
Std. Box
Std. Ctn.
1/4"
1/4"
1/4"
1/4"
5/16"
5/16"
3/8"
3/8"
1/2"
1/2"
1/2"
1/2"
1"
1"
1-1/4"
1-1/4"
100
100
100
100
100
100
50
50
1000
1000
1000
1000
1000
500
500
250
Set-Bolt
Displacement Controlled Expansion Anchor
Base Material
Concrete
Size Range
1/4" x 1-3/4" to 1/2" x 4-1/4"
Anchor Material
Round Head LoK-Bolt AS 304 STAINLESS STEEL
Cat. No.
size
6180S
1/4" x 2-1/4"
Drill Dia.
Min. Embed
Std. Box
Std. Ctn.
1/4"
1/2"
100
1000
Carbon Steel
The Set-Bolt is a one piece, stud style anchor with an external bottom-bearing
expansion plug. It is available in carbon steel for use in concrete, stone and solid
masonry units.
Combo Flat Head LoK-Bolt AS CARBON STEEL
Cat. No.
Size
5305S
5310S
5315S
5320S
5325S
5330S
5340S
5345S
5350S
5360S
1/4" x 1-1/2"
1/4" x 2-1/4"
1/4" x 3"
1/4" x 4"
1/4" x 5-1/4"
5/16" x 2-1/4"
3/8" x 2-3/4"
3/8" x 4"
3/8" x 5"
3/8" x 6"
Drill dia.
Min. Embed.
Std. Box
Std. Ctn.
1/4"
1/4"
1/4"
1/4"
1/4"
5/16"
3/8"
3/8"
3/8"
3/8"
1/2"
1/2"
1/2"
1/2"
1/2"
1"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
100
100
100
100
100
100
50
50
50
50
1000
1000
1000
500
500
1000
300
250
250
250
Drill dia.
Min. Embed.
Std. Box
Std. Ctn.
1/4"
1/4"
3/8"
3/8"
3/8"
1/2"
1/2"
1-1/4"
1-1/4"
1-1/4"
100
100
50
50
50
1000
1000
250
250
250
Combo Flat Head LoK-Bolt AS 304 sTAINLESS STEEL
Cat. No.
Size
6170S
6172S
6174S
6175S
6176S
1/4" x 2-1/4"
1/4" x 3"
3/8" x 4"
3/8" x 5"
3/8" x 6"
These parts do not have a compression ring.
18
Cat. No.
Size
7101
7123*
7126
7134*
7151
1/4" x 1-3/4"
3/8" x 2-1/4"
3/8" x 3"
3/8" x 6"
1/2" x 4-1/4"
Min. Depth
Thread Length
Std. Box
Std. Ctn.
1-3/8"
1-5/8"
1-5/8"
1-5/8"
1-7/8"
5/8"
5/8"
1-3/8"
1-3/8"
1-7/8"
100
50
50
50
25
1000
250
250
125
* Discontinued item once current stock exhausted.
WEDGE-BOLT+ • WEDGE-BOLT 316 • WEDGE-BOLT OT
Code listed
Code listed
cracked concrete
MASONRY
ICC-ES ESR-2526
ICC-ES ESR-1678
city of los angeles
Wedge-Bolt+
Screw Anchor
Base Material
Normal-Weight Concrete, Sand-Lightweight Concrete, Concrete Over Metal Deck,
Grouted CMU
Size Range
Anchor Material
Zinc Plated Carbon Steel Body, and Hex Head or Mechanically Galvanized Carbon
Steel Body and Hex Head
The Wedge-Bolt+ anchor is a one piece, heavy duty screw anchor with a
finished hex head. It is simple to install, easy to identify and fully removable. The
Wedge-Bolt+ has many features and benefits that make it well suited for many
applications in a variety of base materials. The anchor is designed for consistent
and reliable performance in cracked and uncracked concrete.
Install with Powers Wedge-Bit™
Wedge-Bolt + Screw Anchor (Carbon Steel)
Diameter size & Length
7204SD
7206SD
7207SD
7208SD
7210SD
7220SD
7222SD
7224SD
7226SD
7228SD
7230SD
7240SD
7242SD
7244SD
7248SD
7250SD
7268SD
7252SD
7260SD
7262SD
7264SD
7266SD
7270SD
7280SD
7282SD
7284SD
7286SD
7288SD
7290SD
1/4" x 1-1/4"*
1/4" x 1-3/4"*
1/4" x 2"
1/4" x 2-1/4"
1/4" x 3"
3/8" x 1-3/4"*
3/8" x 2-1/2"
3/8" x 3"
3/8" x 4"
3/8" x 5"
3/8" x 6"
1/2" x 2"*
1/2" x 2-1/2"*
1/2" x 3"
1/2" x 5"
1/2" x 6"
1/2" x 6-1/2"
1/2" x 8"
5/8" x 3"*
5/8" x 4"
5/8" x 5"
5/8" x 6"
5/8" x 8"
3/4" x 3"*
3/4" x 4"*
3/4" x 5"
3/4" x 6"
3/4" x 8 "
3/4" x 10"
Diameter size & length
7726SD
7728SD
7730SD
7746SD
7748SD
7750SD
7751SD
7752SD
7764SD
7766SD
7768SD
7770SD
3/8" x 4"
3/8" x 5"
3/8" x 6"
1/2" x 4"
1/2" x 5"
1/2" x 6"
1/2" x 6-1/2"
1/2" x 8"
5/8" x 5"
5/8" x 6"
5/8" x 6-1/2"
5/8" x 8"
STD. BOX
STD. CTN.
50
50
50
50
25
25
25
25
25
25
25
25
250
250
150
150
100
75
75
75
75
75
75
75
Wedge-Bolt 316 Stainless Steel
1/4" Diameter, 3/8" Diameter Through 3/4" Diameter (Cracked And Uncracked
Concrete), Grouted CMU
Cat. No.
Cat. No.
MECHAN I CAL
Wedge-Bolt+ Mechanically galvanized
Min. embed.
Std. box
std. Ctn.
1"
1"
1-3/4"
1-3/4"
1-3/4"
1-1/2"
2-1/8"
2-1/8"
2-1/8"
2-1/8"
2-1/8"
1-3/4"
1-3/4"
2-1/2"
2-1/2"
2-1/2"
2-1/2"
2-1/2"
2-1/2"
3-1/4"
3-1/4"
3-1/4"
3-1/4"
2-1/2"
3"
4-1/4"
4-1/4"
4-1/4"
4-1/4"
100
100
100
100
100
50
50
50
50
50
50
50
50
50
25
25
25
25
25
25
25
25
25
20
20
20
20
10
10
600
600
600
600
500
300
300
250
250
250
150
150
200
150
100
75
75
75
100
100
75
75
75
60
60
60
60
40
40
* Sizes which are less than the minimum standard anchor length for strength design. The published length is
measured from below the hex washer head to the end of the anchor. Wedge-Bolt+ is marked with a blue tip and
must be installed with a matched tolerance Wedge-Bit.
The 316 SS Wedge-Bolt screw anchor is specifically engineered for
applications where additional corrosion resistance is desired. This anchor can
be easily installed with either an impact wrench or conventional hand socket.
Install with Powers Wedge-Bit™
316 Stainless Steel Wedge-Bolt Screw Anchor
Cat. No.
Dia. size & length
07870
07872
07876
07878
07880
07882
07884
07886
07888
07890
07892
07894
1/4"
1/4"
1/4"
1/4"
3/8"
3/8"
3/8"
3/8"
1/2"
1/2"
1/2"
1/2"
x 2"
x 3"
x 4"
x 5"
x 2-1/2"
x 3"
x 4"
x 5"
x 3"
x 4"
x 5"
x 6"
Std. box
Std. Ctn.
100
100
100
100
50
50
50
50
50
50
25
25
600
500
500
500
300
250
250
150
150
150
100
75
Wedge-Bolt Orange Tip
The Carbon Steel Wedge-Bolt OT screw anchor is a specifically engineered part
for the racking industry. This anchor is available in a finished hex head design
and can be easily installed with either an impact wrench or conventional hand
socket. This anchor, unlike Blue Tip Wedge-Bolt, can be installed with regular
ANSI standard carbide drill bits but requires larger clearance holes.
Orange Tip (OT) = Install with ANSI Bit
Wedge-Bolt OT Screw Anchor
Cat. No. Dia. size & length ANSI BIT DIA.
7215
7216
7217
7218
7214
7219
7221
7227
7229
7233
7231
7232
1/4" x 3"
3/8" x 4"
1/2" x 4"
1/2" x 5"
1/2" x 6"
5/8" x 4"
5/8" x 5"
5/8" x 6"
5/8" x 7"
1/2" x 6-1/2"
3/4" x 6"
3/4"x 8"
1/4"
3/8"
1/2"
1/2"
1/2"
5/8"
5/8"
5/8"
5/8"
1/2"
3/4"
3/4"
Clearance hole dia.
3/8”
1/2”
5/8”
5/8”
5/8"
3/4”
3/4”
3/4"
3/4"
5/8”
7/8"
7/8"
Min. embed. Thread length std. Box std. Ctn
1"
1-1/2"
1-3/4"
1-3/4"
1-3/4"
2-1/2"
2-1/2"
2-1/2"
2-1/2"
1-3/4"
2-1/2"
2-1/2"
2-3/4"
3-3/4"
3-3/4"
3-3/4"
3-3/4"
3-3/4"
3-3/4"
3-3/4"
3-3/4"
3-3/4"
4-1/2"
6"
100
50
50
25
25
25
25
25
25
25
20
10
500
250
150
100
75
100
75
75
75
75
60
40
19
MECHANI CAL
WEDGE-BIT • TAPPER+ XTREME
Wedge-Bit™ Drill Bits
MIAMI-DADE COUNTY
APPROVED
For proper performance, the Carbon Steel Wedge-Bolt and 410 Stainless Steel
Wedge-Bolt anchors must be installed with a Wedge-Bit. The Wedge-Bit has a
special matched tolerance range designed to provide optimum performance for
the anchor. The available shank styles and sizes are listed below.
SDS-PLUS Wedge-Bit
Cat. NO.
DRILL Size
USABLE LENGTH
OVERALL LENGTH
std. POUCH
1312
1314
1315
1316
1318
1319
1332
1320
1322
1334
1335
1324
1326
1336
1328
1330
1/4"
1/4"
1/4"
3/8"
3/8"
3/8"
3/8"
1/2"
1/2"
1/2"
1/2"
5/8"
5/8"
5/8"
3/4"
3/4"
2"
4"
6"
4"
6"
16"
10"
4"
8"
10"
16"
6"
10"
16"
6"
10"
4"
6"
8"
6"
8"
18"
12"
6"
10"
12"
18"
8"
12"
18"
8"
12"
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Code listed
ICC-ES ESR-3068
UNCracked concrete
Tapper+® Xtreme
Concrete Screw
Base Material
Uncracked Concrete
Size Range
5/16" x 1-3/4" to 5/16" x 6"
Anchor Material
Carbon Steel
The new Tapper+ Xtreme concrete screw is fully threaded in lengths up to
3-1/4" for light gauge metal attachment to CMU. It is easily installed 2-1/2" added strength with low torque, and installation drive mechanisms, -5/16" hex
head and #3 Phillips. Choice of head styles: hex flange head, trim hex head, flat
and trim flat. Tested to meet ICC-ES Standards for uncracked concrete.
Silver TAPPER+ Xtreme standard pack*
HWH Cat. No. THH Cat. No.
Heavy Duty Straight Shank Wedge-Bit
Cat. No.
DRILL Size
1370
1372
1380
1384
1390
1394
1396
1397
1/4"
1/4"
3/8”
3/8"
1/2"
1/2"
5/8"
3/4"
USABLE LENGTH
OVERALL LENGTH
std. POUCH
2-3/4"
4"
4"
11"
4"
11"
11"
11"
4"
6”
6"
13"
6"
13"
13"
13"
1
1
1
1
1
1
1
1
Spline Wedge-Bit
Cat. No.
DRILL Size
USABLE Length
OVERALL Length
std. Pouch
1340
1342
1344
1348
1/2"
1/2"
5/8"
3/4"
8"
11"
8"
8"
13"
16"
13"
13"
1
1
1
1
2200SD
2202SD
2204SD
2206SD
2208SD
2210SD
2230SD
2232SD
2234SD
2336SD
2238SD
PFH Cat. No.
2212SD
2214SD
2216SD
2218SD
2220SD
2222SD
TFH Cat. No.
Screw Size
Std. Box
Std. Ctn
2240SD
2242SD
2244SD
2246SD
2248SD
2250SD
5/16" x 1-3/4"
5/16" x 2-1/4"
5/16" x 2-3/4"
5/16" x 3-1/4"
5/16" x 4"
5/16" x 5"
5/16" x 6"
100
100
100
100
100
100
100
500
500
500
500
500
500
500
White Perma-Seal coating available by special order.
White TAPPER+ Xtreme standard pack*
2300SD
2302SD
2304SD
2306SD
2308SD
2310SD
2330SD
2332SD
2334SD
2316SD
2318SD
PFH Cat. No.
2312SD
2314SD
2316SD
2318SD
2320SD
2322SD
TFH Cat. No.
Screw Size
Std. Box
Std. Ctn
2340SD
2342SD
2344SD
2346SD
2348SD
2350SD
5/16" x 1-3/4"
5/16" x 2-1/4"
5/16" x 2-3/4"
5/16" x 3-1/4"
5/16" x 4"
5/16" x 5"
5/16" x 6"
100
100
100
100
100
100
100
500
500
500
500
500
500
500
Bronze Perma-Seal coating available by special order.
Bronze TAPPER+ Xtreme standard pack*
SDS-Max Wedge-Bit
Cat. NO.
DRILL Size
USABLE Length
OVERALL Length
std. Pouch
1354
1356
1357
1358
1/2"
5/8"
5/8"
3/4"
8"
8"
16"
8"
13"
13"
21"
13"
1
1
1
1
2600SD
2602SD
2604SD
2606SD
2608SD
2610SD
2630SD
2632SD
2634SD
2636SD
2638SD
PFH Cat. No.
2612SD
2614SD
2616SD
2618SD
2620SD
2622SD
TFH Cat. No.
Screw Size
Std. Box
Std. Ctn
2640SD
2642SD
2644SD
2646SD
2648SD
2650SD
5/16" x 1-3/4"
5/16" x 2-1/4"
5/16" x 2-3/4"
5/16" x 3-1/4"
5/16" x 4"
5/16" x 5"
5/16" x 6"
100
100
100
100
100
100
100
500
500
500
500
500
500
500
HWH = Hex Washer Head (slotted); PFH = Phillips Flat Head; TFH = Trim Flat Head; FHH = Flange Hex Head
* One Tapper+ drill bit included in each standard box.
Tapper+ Xtreme SDS-PLus bit
Cat. No.
Size
1314
1315
1/4" x 6"
1/4" x 8"
Usable Length
Std. pack
4"
6"
1
1
Tapper+ Xtreme installation tools
20
Cat. No.
description
2291SD
Tapper+ Xtreme Installation Kit
std. box
1
TAPPER+
Code listed
concrete
Wood-to-wood
ICC-ES ESR-3068
Code listed
chemically treated lumber
Masonry (CMU)
ICC-ES ESR-3213
MIAMI-DADE COUNTY
APPROVED
Tapper+®
2486SD†
2488SD†
2490SD
2492SD
2494SD
2495SD
2496SD
2505SD
2506SD†
2507SD†
2508SD
2509SD
2510SD
2511SD
2512SD
Cat. No. FHH
8715SD†
8716SD
8717SD
8718SD
Cat. No. TFH
8719SD†
8720SD
8721SD
8722SD
8723SD
screw size
std. box
st. ctn.
3/16" x 4"
1/4" x 1-1/4"
1/4" x 1-3/4"
1/4" x 2-1/4"
1/4" x 2-3/4"
1/4" x 3-1/4"
1/4" x 3-3/4"
1/4" x 4"
100
100
100
100
100
100
100
100
500
500
500
500
500
500
500
500
† Sizes which are less than the minimum standard anchor length for strength design
ICC-ES ESR-3042
Code listed
Cat. No. PFH
MECHAN I CAL
Code listed
Cat. No. HWH
Bronze Perma-Seal TAPPER+ Standard pack*
ICC-ES ESR-3196
Cat. No. HWH
Cat. No. pfh
Screw Size
9975SD†
9976SD†
9977SD†
9978SD†
1/4" x 1-1/4"
1/4" x 1-3/4"
Std. Box
Std. Ctn.
100
100
500
500
Concrete Screw
White Perma-Seal TAPPER+ Standard pack*
Base Material
Concrete, Block, Brick, Wood, Pressure Treated Lumber
Size Range
3/16" x 1-1/4" to 1/4" x 6"
Cat. No. Hwh
Cat. No. PFH
2400SD†
2402SD†
2404SD
2440SD†
2442SD†
Anchor Material
Cat. No. FHH
Cat. No. TFH
2448SD
Carbon Steel
The Tapper+ is a one-piece self-tapping concrete screw for use in a variety of
light to medium duty applications in base materials including concrete, masonry
and wood. It features a corrosion resistant Perma-Seal® coating and an optimized thread design for lower torque. The screw also incorporates a gimlet drill
point for wood base materials (no pre-drilling required). Tapper+ is available in a
variety of head styles and colors to match the application.
2410SD
2412SD
2420SD†
2449SD
2460SD†
8706SD†
8707SD
8708SD
8709SD
2424SD
2426SD
2430SD
2435SD
8710SD†
8711SD
8712SD
8713SD
8714SD
screw size
std. box
std. ctn.
3/16" x 1-1/4"
3/16" x 1-3/4"
3/16" x 2-1/4"
3/16" x 3-1/4"
3/16" x 3-3/4"
3/16" x 4"
1/4" x 1-1/4"
1/4" x 1-3/4"
1/4" x 2-1/4"
1/4" x 2-3/4"
1/4" x 3-1/4"
1/4" x 3-3/4"
1/4" x 4"
100
100
100
100
100
100
100
100
100
100
100
100
100
500
500
500
500
500
500
500
500
500
500
500
500
500
Blue Perma-Seal TAPPER+ Standard pack*
HWH Cat. No.
PFH Cat. No.
Screw Size
Std. Box
Std. Ctn
2700SD†
2702SD†
2704SD
2706SD
2708SD
2710SD
2712SD
2720SD†
2722SD†
2724SD
2726SD
2728SD
2730SD
2732SD
2734SD
2740SD†
2742SD†
2744SD
2746SD
2748SD
2750SD
2752SD
2760SD†
2762SD†
2764SD
2766SD
2768SD
2770SD
2772SD
2774SD
2776SD
3/16" x 1-1/4"
3/16" x 1-3/4"
3/16" x 2-1/4"
3/16" x 2-3/4"
3/16" x 3-1/4"
3/16" x 3-3/4"
3/16" x 4"
1/4" x 1-1/4"
1/4" x 1-3/4"
1/4" x 2-1/4"
1/4" x 2-3/4"
1/4" x 3-1/4"
1/4" x 3-3/4"
1/4" x 4"
1/4" x 5"
1/4" x 6"
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
500
500
500
500
500
500
500
500
500
500
500
500
500
500
100
100
Drill Bits for Perma-Seal® Tapper+®
straight shank
Cat. No.
Size
2781SD
2782SD
2783SD
2785SD
2786SD
2787SD
2788SD
2789SD
5/32" x 3-1/2"
5/32" x 4-1/2"
5/32" x 5-1/2"
3/16" x 3-1/2"
3/16" x 4-1/2"
3/16" x 5-1/2"
3/16" x 6-1/2"
3/16" x 7-1/2"
Usable Length
Std. Tube
Wt./100
2"
3"
4"
2"
3"
4"
5"
6"
10
10
10
10
10
10
10
10
1/4
1/4
1/4
1/4
1/4
1/2
1/2
1/2
Usable Length
Std. Tube
Wt./10
3"
4"
3"
4"
1
1
1
1
1
1
1
1
HWH = Hex Washer Head (slotted); PFH = Phillips Flat Head; TFH = Trim Flat Head; FHH = Flange Hex Head.
† Sizes which are less than the minimum standard anchor length for strength design.
Hex Shank SDS-Plus
Silver Perma-Seal TAPPER+ Standard pack*
Cat. No. HWH
Cat. No. PFH
2498SD†
2500SD†
2501SD
2502SD
2503SD
2504SD
Cat. No. FHH
Cat. No. TFH
screw size
std. box
st. ctn.
3/16" x 1-1/4"
3/16" x 1-3/4"
3/16" x 2-1/4"
3/16" x 2-3/4"
3/16" x 3-1/4"
3/16" x 3-3/4"
100
100
100
100
100
100
500
500
500
500
500
500
Cat. No.
Size
2793SD
2794SD
2796SD
2797SD
5/32" x 5"
5/32" x 7"
3/16" x 5"
3/16" x 7"
21
MECHANI CAL
SS TAPPER • TAPPER DRILL BITS
Stainless Steel Tapper™
Concrete Screw
Tapper Drill Bits
MIAMI-DADE COUNTY
APPROVED
Tapper Drill Bits in the diameters listed are nominal size. Tapper anchors must be
installed with special tolerance Tapper drill bits. 1/4”, Type 304 Stainless Steel
Tapper anchors require the use of specific tolerance Tapper drill bits, which are
gold or silver colored, to denote the standard size and special application size
for harder materials. Tolerance Range = 0.168” to 0.175” for the 5/32” and
0.202” to 0.204” for the 3/16” bits.
Base Material
Concrete, Block and Brick
Size Range
3/16" x 1-1/4" to 1/4" x 6"
Anchor Material
Type 304 & Type 410 Stainless Steel
The Tapper Anchoring System is a family of screw anchors, specially designed
drill bits and installation tools designed to meet the needs of most light to
medium duty applications in concrete, block and brick. The Tapper concrete
screw anchor is produced in either hex washer head or Phillips flat head styles
from Type 304 and Type 410 stainless steel.
Standard Packaging - 100 screws and 1 drill per box
Type 304 Stainless Steel TAPPER HEX HEAD†
Cat. No.
Size
2880
2881
2882
2883
1/4" x 1-1/4"
1/4" x 1-3/4"
1/4" x 2-1/4"
1/4" x 2-3/4"
Std. Box
100
100
100
100
Std. Ctn. Drill Bit Ref. Straight
500
500
500
500
2894
2894
2895
2895
Drill Bit Ref. SDS Hex
2790
2790
2790
2790
†Stainless Steel Tapper screws require the use of special Tapper drill bits. These special drill bits are gold or silver colored for identification. They cannot be used with the Perma-Seal® Tapper or 410 Stainless Steel Tapper.
Carbide Drill Bits for Type 410 SS TAPPER
Hex shank SDS-Plus
Cat. No.
Size
2793
2794
2796
2797
5/32" x 5"
5/32" x 7"
3/16" x 5"
3/16" x 7"
Usable Length
Std. Tube
3"
5"
3"
5"
1
1
1
1
Carbide Drill Bits for Type 304 SS TAPPER
This is the standard bit for use with Type 304 Stainless Steel Tapper.
It is for use in standard weight concrete and block, tolerance = 0.215" to
0.216". This bit is gold colored for identification.
(Do not use with Perma-Seal or Type 410 SS Tapper)
Straight Shank
Type 304 Stainless Steel TAPPER PHILLIPS flat HEAD†
Cat. No.
Size
2887
2888
2889
2890
1/4" x 1-1/4"
1/4" x 1-3/4"
1/4" x 2-1/4"
1/4" x 2-3/4"
Std. Box
100
100
100
100
Std. Ctn. Drill Bit Ref. Straight
500
500
500
500
2894
2894
2895
2895
2790
2790
2790
2790
†Stainless Steel Tapper screws require the use of special Tapper drill bits. These special drill bits are gold or silver colored for identification. They cannot be used with the Perma-Seal® Tapper or 410 stainless steel Tapper.
Cat. No.
Size
2894
2895
3/16" x 3-1/2"
3/16" x 4-1/2"
Usable Length
Std. Tube
2"
3"
10
10
Usable Length
Std. Tube
3"
1
SDS Hex
Cat. No.
Size
2790
3/16" x 5-1/2"
Tapper Installation Tools
Type 410 Stainless Steel Tapper Hex Head
Cat. No.
Size
4180
4181
4182
4183
4110
4112
4114
4116
4117
4119
4127
4128
4129
3/16" x 1-1/4"
3/16" x 1-3/4"
3/16" x 2-1/4"
3/16" x 2-3/4"
1/4" x 1-1/4"
1/4" x 1-3/4"
1/4" x 2-1/4"
1/4" x 2-3/4"
1/4" x 3-1/4"
1/4" x 3-3/4"
1/4" x 4"
1/4" x 5"
1/4" x 6"
Std. Box
Std. Ctn.
Drill Bit Ref. Straight
100
100
100
100
100
100
100
100
100
100
100
100
100
500
500
500
500
500
500
500
500
500
500
500
500
500
2781
2781
2782
2782
2785
2785
2786
2786
2786
2786
2787
2788
2788
2793
2793
2793
2793
2796
2796
2796
2796
2796
2796
2797
-
installation tools for 3/16" and 1/4" Tapper
CAT. No.
Description
2791
2792*
2795
Tapper 1000 Tool (as shown)
Condrive®† 2000
1000 SDS Extension (8")
Max Screw Length
Max. Bit Length
STD. Box
4"
2-3/4"
6"
5-1/2"
4-1/2"
7-1/2"
1
1
1
*This tool cannot be used with SDS Drill Bits or PFH screws.
TAPPER 1000 REPLACEMENT PARTS
CAT. NO.
Description
2953
2964
Drive Sleeve Assembly (5-3/4")
Blue 3/16" Hex Wedge-Bolt® Socket
Std. Box
1
1
Type 410 Stainless Steel Tapper Phillips Flat Head
22
Cat. No.
Size
4185
4186
4187
4188
4118
4120
4123
4124
4125
3/16" x 1-1/4"
3/16" x 1-3/4"
3/16" x 2-1/4"
3/16" x 2-3/4"
1/4" x 1-1/4"
1/4" x 1-3/4"
1/4" x 2-1/4"
1/4" x 2-3/4"
1/4" x 3-1/4"
Std. Box
Std. Ctn.
Drill Bit Ref. Straight
100
100
100
100
100
100
100
100
100
500
500
500
500
500
500
500
500
500
2781
2781
2782
2782
2785
2785
2786
2786
2786
2793
2793
2793
2793
2796
2796
2796
2796
2796
COnDRIVE® 2000 REPLACEMENT PARTS†
Cat. No.
Description
2956
2957
1/4" Hex Key
5/16" Hex Key
† Condrive® is a Registered Trademark of Illinois Tool Works.
Std. Box
1
1
snake • SMART DI+ • Hollow-Set Dropin
ICC-ES ESR-2272
Cracked concrete
Snake+®
Cat. No.
Size
Std. Box
Std. Ctn.
1/4"
3/8"
1/2"
1
1
1
6
6
6
Size
Std. Box
Std. Ctn.
3/8" (for 1/4" Smart DI+)
1
1
1
12
12
12
00425SD
00427SD
00429SD
city of los angeles
Internally Threaded Self-Tapping Anchor
DI+ Tool
Base Material
Normal-Weight Concrete, Structural Sand-Lightweight Concrete,
Concrete Over Metal Deck
Size Range
1/4" -1/2"diameter (Cracked and Uncracked Concrete)
MECHAN I CAL
Code listed
DI+ Drill
Anchor Material
Cat. No.
Zinc Plated Carbon Steel
The Snake+ anchor is an internally threaded, self-tapping screw anchor
designed for performance in cracked and uncracked concrete. Suitable base
materials include normal-weight concrete, structural sand-lightweight concrete
and concrete over metal deck. The Snake+ screw anchor is installed into a
drilled hole with a power tool and a Snake+ setting tool. A hammer is not
used for installation.
00391SD
00397SD
00410SD
Snake+
Cat. No.
Size
6400SD
6401SD
6403SD
1/4"
3/8"
1/2"
Min. Hole Depth
Internal Thread Depth Std. Box
1-5/8"
1-5/8"
2-1/2"
22/32"
11/16"
29/32"
100
50
50
Std. Ctn.
1000
500
300
Extra Snake & Snake+ Setting Tools
Cat. No.
6402SD
6407SD
6404SD
Size
Std. Box
Std. Ctn.
1/4"
3/8"
1/2"
1
1
1
250
250
250
Lock
Drill
Drill hole with the
Smart DI+ drill bit
Lock on Smart DI+
setting tool
Drive
Drive the plug with the
same tool used to drill
Smart DI+® Anchor (Drop-In)
Internally Threaded Expansion Anchor
Base Material
Hollow-Set Dropin™
Concrete
Size Range
1/4" to 1/2"
Base Material
Concrete, Block, Brick, Pre-cast Hollow Core Plank, Stone
Anchor Material
Carbon Steel
Size Range
1/4" to 5/8"
With Powers new patented innovation, the Smart DI+™ Anchor (Drop-In),
contractors can now reduce the amount of hammer blows when setting by
approximately 25% compared to competitive brands. Once the setting tool is
flush, your anchor is set! The new patented plug design yields a higher percentage of the expansion at the bottom of the anchor, exactly where it is needed.
Smart DI+™ Anchor (Drop-In), can also be set using our new Smart Tool. Drill
your hole, slide the tool sleeve over the carbide drill and lock into place. The
hammer drill now does all the work setting the anchor.
Smart DI+
Cat. No.
Size
6304SD
6306SD
6308SD
1/4"
3/8"
1/2"
Std. Box
Std. Ctn.
100
50
50
1000
500
300
Anchor Material
Zamac Alloy with Carbon Steel or Stainless Steel Cones
The Hollow-Set Dropin anchor is designed for anchoring in hollow base
materials such as hollow concrete block, brick with weep holes and hollow
core pre-cast concrete plank. It can also be used in solid base materials. Hollow
masonry materials often have a relatively thin outer wall thickness. During the
drilling process, spalling on the back side of the wall can decrease the wall thickness available for anchoring to 1" or less. The design of the Hollow-Set Dropin
overcomes this problem.
Zamac Body with Carbon Steel Cone
Cat. No.
Size
Drill Dia.
9320
9330
9340
9350
9360
1/4"
5/16"
3/8"
1/2"
5/8"
3/8"
5/8"
5/8"
3/4"
1"
Overall Length Sleeve Length
7/8"
1-5/16"
1-5/16"
1-3/4"
2"
5/8"
15/16"
15/16"
1-1/4"
1-1/2"
Std. Box
Std. Ctn.
100
50
50
50
25
1000
500
500
250
125
23
MECHANI CAL
Steel Dropin • MINI DROPIN
Zamac Body with STAINLESS Steel Cone
Cat. No.
9420
9440
Type 316 Stainless Steel Dropin
Size
Drill Dia.
Overall Length
Sleeve Length
Std. Box
Std. Ctn.
Cat. No.
Size
1/4"
3/8"
3/8"
5/8"
7/8"
1-5/16"
5/8"
15/16"
100
100
1000
500
6224
6226
6228
6230
6232
1/4"
3/8"
1/2"
5/8"
3/4"
SOLID Base material Setting Tools
Cat. No.
Size
9322
9342
9352
9362
1/4"
5/16" & 3/8"
1/2"
5/8"
Std. Box
Std. Ctn.
1
1
1
1
1
1
1
1
Drill Dia.
Min. Depth
Thread Depth
Std. Box
Std. Ctn.
3/8"
1/2"
5/8"
7/8"
1"
1"
1-9/16"
2"
2-1/2"
3-3/16"
7/16"
5/8"
13/16"
1-3/16"
1-3/8"
100
50
50
25
10
1000
500
300
125
50
Drill Dia.
Min. Depth
Thread Depth
Std. Box
Std. Ctn.
5/8"
1"
2"
3-3/16"
13/16"
1-3/8"
50
10
300
50
Carbon Steel Coil Thread Dropin
Cat. No.
Size
6330
6332
1/2"
3/4"
Use Setting Tool Cat. No. 6309 for 1/2” size, Cat. No. 6313 for 3/4” size.
Setting Tools for steel Dropin anchors
Cat. No.
Size
6305
6307
6309
6311
6313
1/4"
3/8"
1/2"
5/8"
3/4"
HOLLOW Base material Setting Tools
Cat. No.
Size
9323
9333
9343
9353
9363
1/4"
5/16"
3/8"
1/2"
5/8"
Std. Box
Std. Ctn.
1
1
1
1
1
1
1
1
1
1
Std. Box
Std. Ctn.
1
1
1
1
1
250
100
100
50
25
SDS-Plus Accu-Bit for DropIn AND Smart DI+
Cat. No.
Size
00391
00397
00410
00418
00419
SDS-Plus 3/8"Concrete Accu-Bit
SDS-Plus 1"Concrete Accu-Bit
Usable Length
Bits Per Pack
for 1/4" Dropin
for 3/8" Dropin
for 1/2" Dropin
for 5/8" Dropin
for 3/4" Dropin
1
1
1
1
1
Steel Dropin
Base Material
Solid Concrete, Solid Block, Hard Stone
Mini Dropin
Size Range
1/4" to 3/4" Standard Thread, 1/2" & 3/4" in Coil Thread
Anchor Material
Base Material
Carbon Steel and Type 304 or 316 Stainless Steel
Pre-cast Hollow Core Plank, Concrete
Size Range
The Steel Dropin is an all-steel, machine bolt anchor available in carbon steel
and two types of stainless steel. It can be used in solid concrete, hard stone, and
solid block. A coil-thread version for forming applications is also available. A
setting tool is included in each standard carton.
Carbon Steel Dropin (Smooth Wall)
Cat. No.
Size
6304
6306
6308
6320
6312
1/4"
3/8"
1/2"
5/8"
3/4"
Drill Dia.
Min. Depth
Thread Depth
Std. Box
Std. Ctn.
3/8"
1/2"
5/8"
7/8"
1"
1"
1-9/16"
2"
2-1/2"
3-3/16"
7/16"
5/8"
13/16"
1-3/16"
1-3/8"
100
50
50
25
10
1000
500
300
125
50
Drill Dia.
Min. Depth
Thread Depth
Std. Box
Std. Ctn.
3/8"
1/2"
5/8"
1"
1-9/16
2"
7/16"
5/8"
13/16"
100
50
50
1000
500
300
1/4", 3/8" and 1/2"
Anchor Material
Carbon Steel
The Mini Dropin is a carbon steel, machine bolt anchor used in shallow
embedment applications. It can be used in solid concrete and hollow core
concrete plank, and it may be suitable in hard stone and solid block.
Mini Dropin
Cat. No.
Size
6335
6322
6337
1/4"
3/8"
1/2"
Carbon Steel Flanged Dropin (Lipped)
Cat. No.
Size
6324
6326
6328
1/4"
3/8"
1/2"
Rod/Anchor size
6340
6342
6344
1/4"
3/8"
1/2"
Drill Dia.
Overall Length
Thread Depth
Std. Box
Std. Ctn.
3/8"
1/2"
5/8"
1"
1-9/16"
2"
7/16"
5/8"
13/16"
100
50
50
1000
500
250
Min. Depth
Thread Depth
Std. Box
Std. Ctn.
3/8"
1/2"
5/8"
5/8"
3/4"
1"
3/8"
13/32"
5/8"
100
100
50
1000
1000
250
Setting Tools for mini dropin anchors
Cat. No.
Size
6336
6323
6338
1/4"
3/8"
1/2"
Carbon Steel Knurled Wall Dropin
Cat. No.
Drill Dia.
Std. Box
Std. Ctn.
1
1
1
50
50
50
Type 303 Stainless Steel Dropin
24
Cat. No.
Size
6204
6206
6208
6210
6212
1/4"
3/8"
1/2"
5/8"
3/4"
Drill Dia.
Min. Depth
Thread Depth
Std. Box
Std. Ctn.
3/8"
1/2"
5/8"
7/8"
1"
1"
1-9/16"
2"
2-1/2"
3-3/16"
7/16"
5/8"
13/16"
1-3/16"
1-3/8"
100
50
50
25
10
1000
500
300
125
50
SDS-Plus Accu-bit for mini DropIn
Cat. No.
Size
00392
00398
00411
SDS-Plus 3/8" Concrete Accu-Bit
Usable Length
Bits Per Pack
for 1/4" Mini Dropin
1
1
1
DOUBLE • SINGLE • CALK-IN • LAG SHIELD
Cat. No.
Size
Drill Dia.
Min. Depth
Std. Box
Std. Ctn.
9205
9210
9220
9225
9230
9240
9250
8-32
10-24
1/4"-20
5/16"-18
3/8"-16
1/2"-13
3/4"-10
5/16"
3/8"
1/2"
5/8"
3/4"
7/8"
1-1/4"
1/2"
5/8"
7/8"
1"
1-1/4"
1-1/2"
2-1/4"
100
100
100
50
50
50
50
1000
1000
1000
250
250
250
-
Double Expansion Anchor
Shell Expansion Anchor
Base Material
Pre-cast Hollow Core Plank, Concrete
Size Range
Master Pack
1/4", 3/8" and 1/2"
Cat. No.
Size
Drill Dia.
Min. Depth
Master Ctn.
9222
1/4"-20
1/2"
7/8"
1000
-Anchor Material
Carbon Steel
The Double is a dual expansion machine bolt anchor particularly suited for base
materials of questionable strength. It can be used in solid concrete and some
block, brick and stone base materials.
Cat. No.
Size
9510
9515
9520
9525
9530
9535
1/4"
5/16"
3/8"
1/2"
5/8"
3/4"
Anchor Length
Drill Dia.
Min. Hole Depth
Std. Box
Std. Ctn.
1-3/8"
1-5/8"
2"
2-1/2"
2-3/4"
3-15/16"
1/2"
5/8"
3/4"
7/8"
1"
1-1/4"
1-1/4"
1-1/2"
1-3/4"
2-1/4"
2-1/2"
3-1/2"
50
50
50
25
25
10
500
500
250
250
100
50
Single Expansion Anchor
MECHAN I CAL
Calk-In
Calk-In tools purchased separately (not included).
Calk-In Setting Tools
Cat. No.
Size
9201
9211
9221
9226
9231
9241
9251
8
10
1/4"
5/16"
3/8"
1/2"
3/4"
Std. Box
Std. Ctn.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Lag Shield
Base Material
Concrete
Base Material
Size Range
Concrete and Mortar Joints of Block and Brick
1/4" to 5/8"
Size Range
Anchor Material
1/4" to 3/4"
Zamac Alloy
Anchor Material
Zamac Alloy
The Single is a machine bolt anchor designed for use in concrete, and may be
suitable in block, brick and stone base materials. The anchor consists of a
pre-assembled set of expansion shields and an expander cone formed from
Zamac alloy.
Cat. No.
Size
9650
9655
9665
9675
9685
1/4"
5/16"
3/8"
1/2"
5/8"
Anchor Length
Drill Dia.
Min. Hole Depth
Std. Box
Std. Ctn.
1-5/16"
1-1/2"
1-1/2"
2-1/16"
2-5/8"
1/2"
5/8"
5/8"
7/8"
1"
1-3/8"
1-5/8"
1-5/8"
2-1/2"
2-3/4"
50
50
50
25
25
250
250
250
125
125
The Lag Shield is a screw style anchor designed for use with lag bolts.
It is suitable for use in concrete and the mortar joints of block or brick walls.
Lag Shield anchors are formed from Zamac alloy. In harder masonry materials,
short style Lag Shields are used to reduce drilling time. The long style
version is used in soft or weak masonry to engage more base material.
Cat. No.
Size
1051
1055
1101
1105
1151
1155
1201
1205
1251
1255
1301
1305
1/4" Short
1/4" Long
5/16" Short
5/16" Long
3/8" Short
3/8" Long
1/2" Short
1/2" Long
5/8" Short
5/8" Long
3/4" Short
3/4" Long
Calk-In
Machine Screw Anchor
Base Material
Drill Dia.
Min. Embed.
Std. Box
Std. Ctn.
1/2"
1/2"
1/2"
1/2"
5/8"
5/8"
3/4"
3/4"
7/8"
7/8"
1"
1"
1"
1-1/2"
1-1/4"
1-3/4"
1-3/4"
2-1/2"
2"
3"
2"
3-1/2"
2"
3-1/2"
50
50
50
50
50
50
50
50
25
25
25
25
500
500
500
500
500
250
500
200
125
125
125
100
Size Range
8 - 32 to 3/4"- 10
Anchor Material
Zamac Alloy and Lead
The Calk-In is a pre-assembled precision cast calking type machine bolt anchor
which can be used in concrete, block, brick or stone. The anchor consists of
an antimonial lead alloy calking sleeve and a Zamac alloy internally-threaded
expander cone.
25
MECHANI CAL
HELI-PIN • VERTIGO+ / VERTIGO
Heli-Pin™
Steel VERTICAL HANGER
Cat. No.
Facade Anchor
Rod Size
Screw Shank Size & Length
Point Style
Std. Box
Std. Ctn.
1/4"
3/8"
3/8"
3/8"
3/8"
1/4-20 x 1"
1/4-20 x 2"
1/4-20 x 1" (w/nuts)
1/4-20 x 1-1/2"
1/4-20 x 1-1/2" (w/nuts)
#3
#3
#3
#3
#3
100
100
100
100
100
600
500
600
500
500
1/4"
3/8"
1/2"
12-20 x 1-1/2"
12-20 x 1-1/2" (w/nuts)
12-20 x 1-1/2" (w/nuts)
#5
#5
#5
100
100
100
500
500
500
Point Style
Std. Box
Std. Ctn.
#3 for Purlins
Anchor Material
7155
7157
7158
7159
7160
#5 for Beams
Base Material
Concrete, Block, Brick, Stone, Clay Tile and Wood
Size Range
8mm (5/16") x 6" to 8mm (5/16") x 12"
The Heli-Pin anchor is a one-piece, stainless steel helical wall tie system used
for anchoring existing brick veneers to the back-up structural members without
exposed hardware. Existing facades constructed of various masonry materials
can be reattached and reinforced using the Heli-Pin. They are ideal for stabilizing
areas with missing or corroded wall ties as well as retrofits to multiple width
masonry wall sections. The Heli-Pin is installed in predrilled holes with a Heli-Pin
setting tool and a SDS-Plus shank roto-hammer drill.
Cat. No.
Item Description
08341
08342
08343
08344
08345
Heli-Pin Anchor 8mm (5/16") x 6"
Heli-Pin SDS Setting Tool
Std. Box
Std. Ctn.
100
100
100
50
1
1000
1000
1000
500
12
7152
7154
7161
STEEL SIDE HANGER
Cat. No.
Rod Size
1/4"
3/8"
3/8"
3/8"
1/4-20 x 1"
1/4-20 x 1" (w/nuts)
1/4-20 x 1-1/2" (w/nuts)
1/4-20 x 2" (w/nuts)
#3
#3
#3
#3
100
100
100
100
600
600
500
500
1/4"
3/8"
12-20 x 1-1/2"
12-20 x 1-1/2" (w/nuts)
#5
#5
50
100
300
600
Point Style
Std. Box
Std. Ctn.
Type 17
Type 17
Type 17
Type 17
Type 17
Type 17
Type 17
100
100
100
100
100
100
100
500
500
500
500
500
500
500
Point Style
Std. Box
Std. Ctn.
Type 17
Type 17
Type 17
Type 17
100
100
100
100
500
500
500
500
#3 for purlins
7183
7184
7186
7188
#5 for Beams
7200
7201
Vertigo + / Vertigo
®
®
Rod Hanger System
Base Material
Steel, Wood, Concrete
Size Range
1/4" – 1/2"
Wood VERTICAL HANGER
Anchor Material
Carbon Steel
Vertigo is an all steel threaded fastening system for suspending steel threaded
rod and other assemblies. Vertigo can be installed in a variety of base materials
including steel bar joists and beams, wood frame columns and beams, as well as
concrete beams and columns. In wood and steel base materials, Vertigo is also
offered in a side mount style for lateral installation of 1/4" and 3/8" diameter
steel threaded rods onto joists, columns and trusses. For all steel and wood
Vertigo fasteners, a red Vertigo Socket Driver is recommended to provide proper
installation with a screw gun or hammer drill in “rotation only” mode. Concrete
Vertigo fasteners should be installed with the appropriate size standard drive
sockets and hammer drill or powered impact wrench.
Code listed
ICC-ES ESR-2526
Cat. No.
Rod Size
7163
7203
7165
7167
7169
7162
7164
1/4"
3/8"
3/8"
3/8"
3/8"
3/8"
1/2"
1/4" x 2"
1/4" x 1"
1/4" x 2"
1/4" x 3"
1/4" x 4"
5/16" x 2-1/2"
5/16" x 2-1/2"
WOOD SIDE HANGER
Cat. No.
Rod Size
7185
7205
7170
7156
1/4"
3/8"
3/8"
3/8"
1/4" x 1"
1/4" x 1"
1/4" x 2"
5/16" x 2-1/2"
Cracked concrete
CONCRETE vertigo+
CAT. No.
Rod Size
7180SD*
7181SD*
7182SD*
1/4"
3/8"
1/2"
CONCRETE VERTICAL HANGER
Finish
Std. Box
Std Ctn.
Cat. No.
Rod Size
3/8" x 2-1/8"
3/8" x 2-1/8"
3/8" x 2-1/8"
Yellow Dichromate Finish
100
100
50
500
500
250
7171
7173
7175
1/4"
3/8"
1/2"
* Packed with SDS Wedge-Bit
26
Shank Style
1/4" x 1-1/4"
1/4" x 1-1/2"
3/8" x 2-3/4"
ANSI Wedge-Bolt OT thread
Std. Box Std. Ctn.
100
100
50
For Side Mount Concrete Applications use Cat. No. 7185 and 7170 with a 3/16" ANSI Drill Bit
500
500
250
VERTIGO • BANG-IT • WOOD-KNOCKER • SPIKE
MECHAN I CAL
Vertigo Accessories
Code listed
ICC-ES ESR-3657
Cracked concrete
Pole Tool
CAT No.
Description
7166
6’-12’ Pole Tool (includes three Jaw Chuck)
Box
Carton
1
1
Wood-Knocker™
Concrete Inserts
Base Material
Concrete, Lightweight Concrete
Size Range
1/4" to 3/4"
Anchor Material
Driver Socket
CAT No.
Description
7187
7195
7197
7198
Universal Steel & Wood Socket
1/4" Concrete Socket
Color
Std. Box
Std. Ctn.
Red n
Blue n
Blue n
Blue n
5
5
5
5
25
25
25
25
Vertigo Tool Kit
CAT No.
Description
5874
Sleeve Assembly (same as cat. #5874) 1/4" and 3/8" blue
concrete drive sockets and red universal drive socket
Sleeve Assembly
CAT No.
Description
5866
1/4" x 6" Hex Shank SDS Drill Bit
5864
Std. Box
Std. Ctn.
1
10
1
-
Usable Length
Std. Tube
Wt./10
4"
1
1/2
Carbon Steel and Engineered Plastic
Wood-Knocker concrete inserts are installed onto wooden forms used to support a newly poured concrete floor slabs, roof slabs or walls. When the forms
are stripped, the color-coded flange is easily seen embedded in the concrete
surface allowing attachment of steel threaded rod or threaded bolts in sizes
ranging from 1/4" to 3/4" in diameter. The unique six-sided impact plate offers
resistance to rotation within the concrete as a steel threaded rod or threaded
bolt is being installed.
Cat. No.
Description
7550
7552
7554
7556
7558
7567
n 1/4" Brown Wood Knocker
n 3/8" Green Wood Knocker
n 1/2" Yellow Wood Knocker
n 5/8" Red Wood Knocker
n 3/4" Purple Wood Knocker
n 1/2" Coil Thread Wood Knocker
STD. Box
Pallet
200
200
200
150
150
200
9600
9600
9600
6000
6000
9600
Code listed
ICC-ES ESR-3657
Cracked concrete
Spike®
Pre-Expanded Anchor
Bang-It™
Base Material
Concrete Inserts
Concrete, Block
Base Material
Size Range
Concrete, Lightweight Concrete
3/16" x 1" to 1/2" x 6-1/2"
Size Range
Anchor Material
1/4" to 3/4"
Carbon Steel and Type 316 Stainless Steel
Anchor Material
Carbon Steel and Engineered Plastic
Bang-It concrete inserts are designed for installation through pre-drilled metal
composite deck (i.e. “pan deck”) used to support a newly poured concrete
floor or roof slab. Depending upon the size/color chosen, the protective sleeve
protrudes below the surface of the deck allowing overhead attachment of steel
threaded rod in sizes ranging from 1/4" to 3/4" in diameter. The protective sleeve
prevents sprayed fireproofing material and acoustical dampening products from
clogging the internal threads of the insert inside, as well as burying, masking or
losing the insert location. The unique, six-sided impact plate offers resistance to
rotation within the concrete as a steel threaded rod is being installed.
CAT. No.
Description
7540
7542
7544
7546
7548
7560
7562
7564
7566
n 1/4" Brown Bang-It
n 3/8" Green Bang-It
n 1/2" Yellow Bang-It
n 5/8" Red Bang-It
n 3/4" Purple Bang-It
Bang-It Deck Driller Extension
13/16" Carbide Hole Saw for 1/4", 3/8" and 1/2"
1-3/16" Carbide Hole Saw for 5/8", 3/4" and 7/8"
Carbide Hole Saw Center Bit
Pre Drilled Hole
Std. Box
Pallet
13/16"
13/16"
13/16"
1-3/16"
1-3/16"
100
100
100
50
50
1
1
1
1
4000
4000
4000
2400
2400
The Spike anchor is a patented, one-piece, tamper-proof anchor for use in
concrete, block, brick or stone. Several head styles are available and offered
in carbon and type 316 stainless steel. The Spike anchor is formed with an
“s” shaped configuration at the working end of the anchor to create an
expansion mechanism. Since the anchor is pre-expanded, there is no secondary
tightening operation.
Mushroom Head Grade 8.2 Carbon Steel SPIKE
CAT. No.
Size
5502
5503
5504
5506
5508
5510
5511
5512
5522
5523
5524
5526
5528
5530
5531
5532
5546
3/16" x 1"
3/16" x 1-1/4"
3/16" x 1-1/2"
3/16" x 2"
3/16" x 2-1/2"
3/16" x 3"
3/16" x 3-1/2"
3/16" x 4"
1/4" x 1"
1/4" x 1-1/4"
1/4" x 1-1/2"
1/4" x 2"
1/4" x 2-1/2"
1/4" x 3"
1/4" x 3-1/2"
1/4" x 4"
3/8" x 2"
DRILL Dia.
MIN. Embed.
Std. Box
Std.Ctn.
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
3/8"
7/8"
7/8"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
7/8"
1"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-3/4"
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
25
1000
1000
1000
1000
600
600
600
600
1000
1000
1000
600
600
600
600
600
250
27
MECHANI CAL
SPIKE • DRIVE
CAT. No.
Size
5548
5550
5551
5552
5554
5556
5569
5571
5572
5574
5577
3/8" x 2-1/2"
3/8" x 3"
3/8" x 3-1/2"
3/8" x 4"
3/8" x 5"
3/8" x 6"
1/2" x 2-3/4"
1/2" x 3-1/2"
1/2" x 4"
1/2" x 5"
1/2" x 6-1/2"
DRILL Dia.
MIN. Embed.
Std. Box
Std.Ctn.
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
1/2"
1/2"
1/2"
1/2"
1/2"
1-3/4"
1-3/4"
1-3/4"
1-3/4"
1-3/4"
1-3/4"
2-1/2"
2-1/2"
2-1/2"
2-1/2"
2-1/2"
25
25
25
25
25
25
50
50
25
25
25
150
150
150
150
150
125
200
150
125
125
100
Concrete Forming
Forming SPIKE Grade 8.2 Carbon Steel
Cat. No.
Anchor Size
3795
3796
3797
3794
3/16" x 1-1/2"
3/16" x 2"
3/16" x 2-3/4"
1/4" x 2-3/4"
Drill Dia.
Min. Embed.
Std. Box
Std. Ctn.
3/16"
3/16"
3/16"
1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
100
100
100
100
600
600
600
500
While the Spike anchor can easily be installed using a hammer, a specially designed series of drivers and manual tools provide a fast, easy to use method for
installation into concrete and masonry materials. The tools allow Spike anchors
to be installed in confined areas and prevent damage to the fixture from stray
hammer blows.
The published length is measured from below the head to the end of the anchor.
Flat Head Grade 8.2 Carbon Steel SPIKE
CAT. No.
Size
5608
5610
5612
5624
5626
5628
5630
5631
5632
3/16" x 2-1/2"
3/16" x 3"
3/16" x 4"
1/4" x 1-1/2"
1/4" x 2"
1/4" x 2-1/2"
1/4" x 3"
1/4" x 3-1/2"
1/4" x 4"
DRILL Dia.
MIN. Embed.
Std. Box
Std.Ctn.
3/16"
3/16"
3/16"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
100
100
100
100
100
100
100
100
100
600
600
600
1000
600
600
600
600
500
SPIKE Installation Tools
Cat. No.
Tool Description
Tip O.D.
Std. Box
3790
3791
Spike Driver 1000
Spike Driver 2000
1/2"
1/2"
1
1
Tool Description
Tip O.D.
Std. Box
Pipe Spike Setting Tool
5/16"
1
Pipe SPIKE Tool
Cat. No.
The published length is the overall length of the anchor.
3760
Mushroom Head Type 316 Stainless Steel SPIKE
Cat. No.
Size
6602
6603
6604
6606
6623
6624
6626
6628
6630
6646
6648
6650
3/16" x 1"
3/16" x 1-1/4"
3/16" x 1-1/2"
3/16" x 2"
1/4" x 1-1/4"
1/4" x 1-1/2"
1/4" x 2"
1/4" x 2-1/2"
1/4" x 3"
3/8" x 2"
3/8" x 2-1/2"
3/8" x 3"
Drill Dia.
Min.Embed.
Std. Box
Std. Ctn.
3/16"
3/16"
3/16"
3/16"
1/4"
1/4"
1/4"
1/4"
1/4"
3/8"
3/8"
3/8"
7/8"
7/8"
1-1/4"
1-1/4"
1"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-3/4"
1-3/4"
1-3/4"
100
100
100
100
100
100
100
100
100
25
25
25
1000
1000
1000
1000
1000
1000
600
600
600
250
250
250
The published length is measured from below the head to the end of the anchor.
Special Application Spike® Anchors
DRIVE®
Split Pin Type Pre-Expander Anchor
Base Material
Concrete
Size Range
3/16" x 1-1/2" to 1/2" x 3"
Anchor Material
Carbon Steel
The Drive is a one piece tamper-proof, pre-expanded anchor available in
carbon steel for use in concrete and stone. Tie-Wire Drive anchors are used for
suspended ceiling applications. The flat head (counter-sunk) style is particularly
suited for wood-to-concrete anchoring. The round head style is for all other
applications requiring fast, permanent installations.
Round Head Drive
Cat. No.
Size
3241
3271
3301
3601
3631
3691
3781
1/4" x 1-1/4"
1/4" x 1-1/2"
1/4" x 2"
1/4" x 2-1/2"
3/8" x 2"
3/8" x 2-1/2"
3/8" x 3-1/2"
1/2" x 3"
Rod Hanging
3211
Pipe SPIKE Grade 8.2 Carbon Steel
Cat. No.
Size
3755
3758
1/4"
3/8"
Drill Dia.
Min. Embed.
Std. Box
Std. Ctn.
3/16"
1/4"
1-1/4"
1-3/4"
100
50
600
300
Suspended ceilings
Tie-Wire SPIKE Grade 8.2 Carbon Steel
28
Cat. No.
Size
3756
3759
3/16"
1/4"
Drill Dia.
Min. Embed.
Tie-Wire Hole Size
Std. Box
Std. Ctn.
3/16"
1/4"
1-1/4"
1-1/4"
3/16"
9/32"
100
100
600
600
Drill Dia.
Min. Depth
Std. Box
Std. Ctn.
1/4"
1/4"
1/4"
1/4"
3/8"
3/8"
3/8"
1/2"
1-1/8"
1-1/8"
1-1/8"
1-1/8"
1-7/8"
1-7/8"
1-7/8"
2-5/8"
100
100
100
100
25
25
25
25
1000
1000
600
600
250
150
150
150
DRIVE • ZAMAC HAMMER-SCREW • SAFE -T PIN
Cat. No.
Size
3092
3122
3152
3162
3242
3272
3302
3332
3362
3392
3/16" x 1-1/2"
3/16" x 2"
3/16" x 2-1/2"
3/16" x 3"
1/4" x 1-1/2"
1/4" x 2"
1/4" x 2-1/2"
1/4" x 3"
1/4" x 3-1/2"
1/4" x 4"
Drill Dia.
Min. Depth
Std. Box
Std. Ctn.
3/16"
3/16"
3/16"
3/16"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
7/8"
7/8"
7/8"
7/8"
1-1/8"
1-1/8"
1-1/8"
1-1/8"
1-1/8"
1-1/8"
100
100
100
100
100
100
100
100
100
100
1000
1000
600
600
1000
600
600
600
600
600
Tie-Wire Drive (13/64” Tie-Wire Hole)
Cat. No.
Size
3244
3245
1/4" x 1-3/4"
1/4" x 1-3/4"
Drill Dia.
Min. Depth
Std. Box
Std. Ctn.
1/4"
1/4"
1-1/8"
1-1/8"
500
100
1000
Zamac Hammer-Screw® Anchor
MECHAN I CAL
flat head drive
Safe-T+ Pin®
Nail Anchor
Base Material
Size Range
1/4" x 1-3/8" and 1/4" x 2-1/2"
Anchor Material
Carbon Steel
The new Powers Safe-T+ Pin is a one piece, all steel, nail drive anchor that can
be used in concrete, block, brick or stone. Each box of Safe-T+ pins comes with
a 6MM SDS carbide drill bit for ease of installation. Typical applications include
HVAC Duct Straps, light to medium duty signage, and termination bar, flooring
ECT. Available in 1 diameter and two lengths. Just drill a hole and hammer it in.
Safe-T+ Pin
Cat. No.
Size
2800SD
2801SD
6mm (1/4") x 1-3/8"
6mm (1/4") x 2-1/2"
Drill Dia.
Std. Box
Std. Ctn.
6mm
6mm
100
100
600
600
Safe-T+ Pin DRILL BIT
Nail Anchor
Base Material
Cat. NO.
DESCRIPTION
2800
Drill Bit
Dia.
USABLE LENGTH
Std. Box
Std. Ctn.
6mm
3-1/4"
1
50
Size Range
Zamac Nailin® Anchor
1/4" x 3/4" to 1/4" x 3"
Drive Pin Type Anchor
Anchor Material
Zamac Alloy with Carbon Steel and Perma-Seal Drive Screw
Base Material
The Zamac Hammer-Screw is a unique, one-step drive anchor featuring a
Phillips type head and an internal screw thread for use in concrete, block, brick
or stone. The anchor has a body formed from corrosion resistant Zamac alloy
with a carbon steel drive screw, and has been developed as an improvement
over standard nailin anchors. The anchor is removable and is also offered with
an optional Perma-Seal coated screw.
Size Range
3/16" x 7/8" to 1/4" x 3"
Anchor Material
Zamac Alloy with Carbon or Stainless Steel Drive Pin
The Zamac Nailin is a tamper-proof nail drive anchor which has a body formed
from Zamac alloy. Nails are available in carbon or stainless steel. The anchor can
be used in concrete, block, brick or stone.
Zamac Hammer-Screw - Mushroom Head / No. 2 Phillips Type Screw CARBON STEEL
Cat. NO.
Size
2839
2840
2842
2844
2846
2848
2850
1/4" x 3/4"
1/4" x 1"
1/4" x 1-1/4"
1/4" x 1-1/2"
1/4" x 2"
1/4" x 2-1/4"
1/4" x 3"
Master Pack WITH CARBON STEEL SCREW
Cat. No.
Size
2939
2940
2942
2944
2946
2948
2949
1/4" x 3/4"
1/4" x 1"
1/4" x 1-1/4"
1/4" x 1-1/2"
1/4" x 2"
1/4" x 2-1/4"
1/4" x 3"
Drill Dia.
Std. Box
Std. Ctn.
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
100
100
100
100
100
100
100
500
500
500
500
500
500
500
Drill Dia.
Std. Box
Std. Ctn.
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
Mushroom Head Zamac Nailin - Carbon Steel Nail
Cat. NO.
Size
2802
2806
2808
2814
2820
2826
2804
3/16" x 7/8"
1/4" x 3/4"
1/4" x 1"
1/4" x 1-1/4"
1/4" x 1-1/2"
1/4" x 2"
1/4" x 3"
Master Pack
Cat. No.
Size
2803
2807
2809
2815
2821
2827
2805
3/16" x 7/8"
1/4" x 3/4"
1/4" x 1"
1/4" x 1-1/4"
1/4" x 1-1/2"
1/4" x 2"
1/4" x 3"
Drill Dia.
Std. Box
Std. Ctn.
3/16"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
100
100
100
100
100
100
100
500
500
50
500
500
500
500
Drill Dia.
Std. Box
Std. Ctn.
3/16"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
Zamac Hammer-Screw - Mushroom Head with No. 2 Phillips Type Perma-Seal Screw
Cat. NO.
Size
Drill Dia.
Std. Box
Std. Ctn.
2817
1/4" x 1-1/4"
1/4"
100
500
Master Pack WITH PERMA-SEAL SCREW
Cat. No.
Size
Drill Dia.
Std. Box
Std. Ctn.
1/4"
1000
1000
2818
1/4" x 1-1/4"
29
MECHANI CAL
NYLON NAILIN
Mushroom Head Nylon Nailin STAINLESS STEEL NAIL
Flat Head Zamac Nailin - Carbon Steel Nail
Cat. No.
Size
2836
2838
1/4" x 1-1/2"
1/4" x 2"
Drill Dia.
Std. Box
Std. Ctn.
1/4"
1/4"
100
100
500
500
Size
2528
2548
1/4" x 1"
1/4" x 1-1/2"
Drill Dia.
Std. Box
Std. Ctn.
1/4"
1/4"
100
100
1000
1000
Drill Dia.
Std. Box
Std. Ctn.
1/4"
2500
2500
Mushroom Head BODIES ONLY
Mushroom Head Zamac Nailin - stainless Steel Nail
Cat. No.
Size
2858
2864
2870
2876
1/4" x 1"
1/4" x 1-1/4"
1/4" x 1-1/2"
1/4" x 2"
Drill Dia.
Std. Box
Std. Ctn.
1/4"
1/4"
1/4"
1/4"
100
100
100
100
500
500
500
500
Nylon Nailin® Anchor
Plastic Drive Pin Type Anchor
Base Material
Size Range
3/16" x 1" to 1/4" x 6"
Anchor Material
Engineered Nylon with Carbon or Stainless Steel Drive Pin
The Nylon Nailin is a pin drive anchor with a body formed from engineered
nylon and nails available in carbon and stainless steel. The anchor can be used
in concrete, block, brick or stone.
Round Head Nylon Nailin - CARBON Steel Nail
Cat. NO.
Size
2431
2451
2521
2541
3/16" x 1"
3/16" x 1-1/2"
1/4" x 1"
1/4" x 1-1/2"
Drill Dia.
Std. Box
Std. Ctn.
3/16"
3/16"
1/4"
1/4"
100
100
100
100
1000
1000
1000
1000
Drill Dia.
Std. Box
Std. Ctn.
1/4"
1/4"
100
100
1000
1000
Drill Dia.
Std. Box
Std. Ctn.
3/16"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
100
100
100
100
100
100
100
1000
1000
1000
1000
1000
1000
1000
Flat Head Nylon Nailin- CARBON Steel Nail
Cat. NO.
Size
2542
2562
1/4" x 1-1/2"
1/4" x 2"
Mushroom Head Nylon Nailin CARBON STEEL NAIL
30
Cat. NO.
Cat. NO.
Size
2433
2513
2523
2543
2563
2573
2583
3/16" x 1"
1/4" x 3/4"
1/4" x 1"
1/4" x 1-1/2"
1/4" x 2"
1/4" x 3"
1/4" x 4"
Cat. NO.
Size
2574
1/4" x 3"
SELECTION GUIDE
Pure50+
36
•
• • • • • • •
AC50 Silver
36
•
• • • • • •
Chem-Stud
37
•
• • • • • • •
Hammer-Capsule
38
•
39
Chisel Point Rod
•
•
ICC-ES ESR-3298
•
•
ICC-ES ESR-2582
ICC-ES ESR-3200
•
•
•
ICC-ES ESR-2583
LARR-25849
•
•
•
ICC-ES ESR-3576
•
•
•
•
•
Tested To
ICC-ES AC 58
•
•
Tested To
ICC-ES AC 58
•
•
•
Anchor Hardware
Straight Cut Rod
• • • • • • • • • • • • • • • •
•
•
37
•
•
Expansion Foam
•
PowerFoam
39
• • • • • • • •
•
TriggerFoam Pro
39
• • • • • • • •
•
Bonding
Sealant
• • • • • •
Wet
• • • • • • •
Dry
•
PowerStick
40
• • • • • • • •
PowerPatch
40
• •
• • • • • • •
MS Polymer
•
Polyurethane
35
Ester Based Resin
PE1000+
Epoxy
• • • • • • •
• • • •
Coated/Plated Carbon Steel
•
2"
34
1-3/4"
AC100+Gold
1-1/2"
• • • • • • •
1" ( #8)
• • • •
1/4"
•
Stone
33
1-3/8"
1-1/4" ( # 10)
7/8" (#7)
3/4" (#6)
5/8" (#5)
1/2" (#4)
3/8" (#3)
Hollow Brick
Solid Brick
Concrete
Page
Injection Adhesives
Pure110+
Code Recognition
Adhesive
Sealant
Glass Capsule Adhesives
Anchor
Chemistry Hole
Condition
Elements
Anchor Diameter
•
ADHESI VE
Base Material
ICC-ES ESR-3263
•
•
•
•
•
• Suitable
May be Suitable
31
ADHESI VE
Powers
7th Edition
Technical
Manual
is now
available!
Please contact your local Powers
Field Engineer at 800-524-3244 to
schedule a Lunch & Learn and receive
your new Tech Manual.
Powers Design Assist
Anchor Software
www.powersdesignassist.com
`
New!
Rock Solid Anchoring Specify with Confidence
®
Pure110+ EPOXY INJECTION ADHESIVE ANCHORING SYSTEM
The new building code requires that all epoxies be tested to a new standard,
110˚ F. Pure110+ has been tested, and approved to that standard and is now
available in original 1:1 mix ratio formula, and new easy-to-dispense 3:1 formula.
Recognized for its freeze / thaw performance and long & short term loading,
Pure110+ can be installed in a wide range of temperatures, base materials and
conditions. Perfect to specify on demanding job sites.
32
ICC-ES ESR (concrete)
Revision Date
Cracked Concrete
Seismic Approval
in Concrete
Rebar Approval
VOC
NSF 61
(potable drinking water)
2010 FBC
ESR-3298
2015 Jan
4
4
4
4
4
4
Anchor software
2
developed to visualize,
quickly calculate, and
specify concrete anchors
in accordance with ACI 318 and CSA A23.3.
Visit: www.powersdesignassist.com
PURE110+
`
New!
08284
08285
08286
08287
08288
08289
ADHESI VE
082900828308296
Code listed
ICC-ES ESR-3298
08292
08282
8280
08465
Cracked concrete
Pure110+®
Adhesive Anchoring System
Pure110+ is a two-component epoxy adhesive anchoring system. The system
includes injection adhesive in plastic cartridges, mixing nozzles, dispensing tools
and hole cleaning equipment. Pure110+ is designed for bonding threaded rod
and reinforcing bar hardware into drilled holes in solid concrete base materials.
Now also available in easy-to-dispense 3:1 mix ratio formula.
Pure110+ cartridges
Cat. No.
Description
08310SD
08321SD
08313SD
08320SD
9 fl. oz. Quik-Shot cartridge 1:1 mix ratio formula
21 fl. oz. dual cartridge 1:1 mix ratio formula
13 fl.oz. 3:1 mix ratio formula
20 fl.oz. 3:1 mix ratio formula
Std. Box
Pallet
12
12
12
12
432
540
540
540
One Pure110+ mixing nozzle is packaged with each cartridge. Pure110+ mixing nozzles must be used to
ensure complete and proper mixing of the adhesive.
Cartridge System Mixing Nozzles
Cat. No.
Description
08294
08281
Extra mixing nozzle (w/8" extension) for Pure110+ Quik-Shot
Mixing nozzle extension, 8" minimum
Extra high flow mixing nozzle (w/8"extension) for
Pure110+ dual cartridge
Flex extension tubing for piston plug
08609
08297
Std. pack Std. Ctn.
08409
08421
08442 08413
08437
08479
08279SD
08298
08497SD 2
2
24
24
2
24
1
12
52073
Hole Cleaning Tools & Accessories
Cat. No.
Description
Length Inches
Std. Pkg.
08284
08285
08275
08286
08278
08287
08288
08289
08290
08291
08283
08296
08282
08280
08292
08465
08466
Wire brush for 7/16" ANSI hole (3/8" rod or #3 rebar)
6-3/4"
6-3/4"
6-3/4"
7-7/8"
7-7/8"
7-7/8"
Wire brush for 1" ANSI hole (7/8" rod or #7 rebar)
11-7/8"
Wire brush for 1-1/8" ANSI hole (1" rod or #8 rebar)
11-7/8"
Wire brush for 1-3/8" ANSI hole (1-1/4" rod or #9 rebar)
11-7/8"
Wire brush for 1-1/2" ANSI hole ( #10 rebar)
11-7/8"
SDS-plus adapter for steel brushes
Standard drill adapter for steel brushes (e.g. Jacobs Chuck)
Steel brush extension, 12"
Hand pump/dust blower (25 fl. oz. cylinder volume)
Air compressor nozzle with extension
Adjustable torque wrench with 1/2 square drive (10 to 150 ft.-lbs.)
Adhesive cleaning kit, includes 4 wire brushes (08284, 08285, 08286,
08287), steel brush extension (08282), SDS-Pus adapter (08283),
standard drill adapter (08296), hand pump/dust blower (08280),
gloves and safety glasses
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
52073
1
Dispensing tools for injection adhesive
Cat. No.
Description
08409
08421
08437
08438
08442
08479
08298
08279SD
08497SD
21 fl. oz. Standard all-metal manual tool
21 fl. oz. High performance manual tool
Manual caulking gun for Quik-Shot
51 fl. oz. Pneumatic tool
21 fl. oz. Battery powered tool (cordless)
High performance caulking gun for Quik-Shot
13 + 20 fl. oz. 3:1 mix ratio manual tool
13 + 20 fl. oz. 3:1 mix ratio battery powered tool
13 + 20 fl. oz. 3:1 mix ratio pneumatic tool
Std. Box
Std. Ctn.
1
1
1
1
1
1
1
1
1
10
10
12
12
6
6
33
ADHESI VE
AC100+ GOLD
pneumatic injection tool delivery system
Mixing nozzle included with each cartridge
Code listed
Code listed
Cracked concrete
MASONRY
ICC-ES ESR-2582
ICC-ES ESR-3200
Cat. No.
Description
08496
28 oz. High Performance Pneumatic Tool
Std. Box
Std. Ctn.
1
1
`
New!
AC100+Gold®
The AC100+Gold is a two-component vinylester adhesive anchoring system.
The system includes injection adhesive in plastic cartridges, mixing nozzles,
dispensing tools and hole cleaning equipment. The AC100+Gold is designed for
bonding threaded rod and reinforcing bar hardware into drilled holes in concrete
and masonry base materials.
Battery injection Dispensing Tool
Cat. No.
Description
08444*
28 oz. High Performance Battery Tool
Std. Box
Std. Ctn.
1
1
* Dispenses 12 cartridges at 70˚F * Dispenses 6 cartridges at 30˚F
AC100+Gold cartridges
Cat. No.
Description
8478SD
8486SD
8490SD
10 fl. oz. Quik-Shot
12 fl. oz. dual cartridge
Std. Box
Std. Ctn.
Pallet
12
-
36
12
8
648
540
240
One AC100+Gold mixing nozzle is packaged with each cartridge.
AC100+Gold mixing nozzles must be used to ensure complete and proper mixing of the adhesive.
Cat. No.
Description
08293
08294
08281
08297
Extra mixing nozzle for AC100+Gold 10 oz. & 12 oz.
Extra mixing nozzle (with 8" extension) for AC100+Gold 28 oz.
Mixing nozzle extension, 8"
Std. Box Std. Ctn.
8437
8484
8494
8495
2
2
2
1
24
24
24
12
8485
Dispensing Tools for Injection Adhesive
34
Cat. No.
Description
08437
08479
08485
08494
08495
AC100+Gold 8 oz., 10 oz. & 12 oz. high performance manual tool
AC100+Gold 28 oz. standard all-metal manual tool
AC100+Gold 28 oz. high performance manual tool
Std. Box
Std. Ctn.
1
1
1
1
1
12
12
20
-
8284
8285
8286
8287
8288
8289
8290
8291
8283
8296
8482
8292
8465
8466
8280
52073
Cat. No.
Description
Length Inches
Std. Pkg.
08284
08285
08275
08286
08278
08287
08288
08289
08290
08291
08283
08296
08282
08280
08292
08465
08466
52073
6-3/4"
6-3/4"
6-3/4"
7-7/8"
7-7/8"
7-7/8"
11-7/8"
11-7/8"
11-7/8"
11-7/8"
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
PE1000+
Code listed
ICC-ES ESR-2583
PE1000+®
8284
8285
8286
8287
8288
8289
8290
8291
8283
8296
8482
8292
8465
8466
8280
ADHESI VE
Mixing nozzle included with each cartridge
The PE1000+ is a two-component, high strength epoxy adhesive anchoring system. The system includes injection adhesive in plastic cartridges, mixing nozzles,
dispensing tools and hole cleaning equipment. The PE1000+ is designed for
bonding threaded rod and reinforcing bar hardware into drilled holes in solid
concrete base materials.
PE1000+ cartridges
Cat. No.
Description
0500SD
0502SD
Std. Box
12
12
One PE1000+ mixing nozzle is packaged with each cartridge.
PE1000+ mixing nozzles must be used to ensure complete and proper mixing of the adhesive.
Cat. No.
Description
08294
08281
08297
Extra mixing nozzle (with an 8" extension) for PE1000+
Mixing nozzle extension, 8"
Std. PKg.
Std. Ctn.
2
2
1
24
24
12
Cat. No.
Description
Length Inches
Std. Pkg.
08284
08285
08275
08286
08278
08287
08288
08289
08290
08291
08283
08296
08282
08280
08292
08465
08466
6-3/4"
6-3/4"
6-3/4"
7-7/8"
7-7/8"
7-7/8"
11-7/8"
11-7/8"
11-7/8"
11-7/8"
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
52073
8279SD
08298
52073
1
8497SD
PE1000+ Dispensing Tools
Cat. No.
Description
8279SD
08298
8497SD
08277
13 oz. + 20 oz. PE1000+ battery tool
13 oz. + 20 oz. PE1000+ heavy duty dispensing tool
13 oz. + 20 oz. PE1000+ pneumatic dispensing tool
Battery for 8279SD
Std. Box
Std.Ctn.
1
1
1
1
12
5
-
35
ADHESI VE
PURE50+ • AC50 SILVER
Code listed
ICC-ES ESR-3576
Cracked concrete
08284
08285
08286
08287
08288
08289
08290
08283
08296
08292
08282
08465
Pure50+™
Pure50+ is a two-component adhesive anchoring system. The system includes
injection adhesive in plastic cartridges, mixing nozzles, dispensing tools and hole
cleaning equipment. Pure50+ is designed for bonding threaded rod & reinforcing
bar hardware into drilled holes in solid concrete base materials.
Pure50+ cartridges
Cat. No.
Description
08600
08605
08651
9 fl. oz. Quik-Shot cartridge
21 fl. oz. cartridge
Std. Box
Pallet
12
12
5
432
540
216
One Pure50+ mixing nozzle is packaged with each cartridge. Pure50+ mixing nozzles must be used to ensure
complete and proper mixing of the adhesive.
Cat. No.
Description
08294
08281
08297
Extra mixing nozzle (with an 8" extension) for Pure50+
Mixing nozzle extension, 8" minimum
Flex extension tubing for pistion plug
Std. pkg.
Std. Ctn.
2
2
1
24
24
12
08409
08421
52073
Cat. No.
Description
Length Inches
Std. Pkg.
08284
08285
08275
08286
08278
08287
08288
08289
08290
08291
08283
08296
08282
08280
08292
08465
08466
6-3/4"
6-3/4"
6-3/4"
7-7/8"
7-7/8"
7-7/8"
11-7/8"
11-7/8"
11-7/8"
11-7/8"
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
52073
8280
1
08437 `
New!
08438 0844208479 Dispensing tools for injection adhesive
Cat. No.
Description
08409
08421
08437
08438
08442
08459
08479
21 fl. oz. High performance manual caulking gun
Std. Box
Std. Ctn.
1
1
1
1
1
1
1
10
10
12
12
AC50 Silver™ Adhesive Anchoring System
tested to
ICC-ES AC58
AC50 Silver is a two-component vinylester adhesive anchoring system.
The system includes injection adhesive in plastic cartridges, mixing nozzles,
dispensing tools and hole cleaning equipment. AC50 Silver is designed for
bonding threaded rod and reinforcing bar hardware into drilled holes in solid
concrete base materials.
AC50 Silver cartridges
Cat. No.
Description
08497
Std. Box
Pallet
8
400
One AC50 Silver mixing nozzle is packaged with each cartridge. AC50 Silver mixing nozzles must be used to
ensure complete and proper mixing of the adhesive
Cat. No.
36
Description
08294 Extra mixing nozzle (with an 8" extension) for AC50 Silver
08281 Mixing nozzle extension, 8" minimum
08297 Flex extension tubing for pistion plug
Std. pkg.
Std. Ctn.
2
2
1
24
24
12
CHEM-STUD
6505
6506
6507
6508
08494
8495
Rod Size
3/4"
7/8"
1"
1-1/4"
Drill Dia.
Length
Std. Box
Std. Ctn.
7/8"
1"
1-1/8"
1-1/2"
6-5/8"
7"
8-1/4"
10-1/4"
5
5
5
5
50
50
50
25
0844408496
Dispensing tools for injection adhesive
Cat. No.
Description
08494
08495
08444
08496
28 fl. oz. High performance manual tool
Std. Box
Std. Ctn.
1
1
1
1
10
10
-
08284
08285
08286
08287
08288
08289
Carbon steel rods are zinc plated according to ASTM B 633. A307 Standard
Carbon Steel, Zinc Plated (ASTM B 633)
ADHESI VE
Cat. No.
Chem-Stud Chisel-Pointed Anchor Rods
Cat. No.
Size
Drill Dia.
Min. Depth
Std. Box
Std. Ctn.
6513
6514
6515
6517
6518*
1/2" x 6-1/2"
5/8" x 7-1/2"
3/4" x 9-5/8"
1" x 12"
1-1/4" x 15"
9/16"
11/16"
7/8"
1-1/8"
1-1/2"
4-1/4"
5"
6-5/8"
8-1/4"
10-1/4"
10
10
10
10
5
50
40
40
10
5
08290
08283
08296
08292
08282
08465
Chem-Stud® Installation Tools
Chem-Stud installation tools consist of a drive adapter which is designed to
fit the rotary hammer drill used and a coupler to hold either threaded rods or
reinforcing bars. The tools for threaded rod and reinforcing bars are different and
can not be interchanged.
Threaded Rod Installation Tools
8280
52073
Couplers for Threaded Rod
Cat. No.
Description
Length Inches
Std. Pkg.
Cat. No.
Size
08284
08285
08275
08286
08278
08287
08288
08289
08290
08291
08283
08296
08282
08280
08292
08465
08466
6-3/4"
6-3/4"
6-3/4"
7-7/8"
7-7/8"
7-7/8"
11-7/8"
11-7/8"
11-7/8"
11-7/8"
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6562
6563
6564
6565
6566
6567
6568
3/8"
1/2"
5/8"
3/4"
7/8"
1"
1-1/4"
52073
Spin-In Type Capsule Adhesive
tested to
ICC-ES AC58
Chem-Stud Capsules
6502
6503
6504
3/8"
1/2"
5/8"
10
10
10
5
5
5
5
Drivers for Threaded Rod Couplers - hex
Cat. No.
Hex Size
6570
6572
1/4"
3/8"
Fits Coupler Size
Std. Box
Std. Ctn.
3/8" to 5/8"
3/4" to 1-1/4"
1
1
10
10
Drivers for Threaded Rod Couplers - SDS-plus
1
The Chem-Stud Anchor System consists of self contained two-part glass capsules and
matching chisel pointed anchor rods which are installed using a rotary hammer drill and
rod adapters. The Chem-Stud adhesive is an ester based resin material packaged in a single
use glass capsules designed for installation of 3/8” through 1-1/2” threaded rods in solid
concrete and masonry materials. It can also be used with chisel pointed reinforcing bars.
Rod Size
Std. Ctn.
1
1
1
1
1
1
1
Cat. No.
Hex Size
6574
6576
1/4"
3/8"
Fits Coupler Size
Std. Box
Std. Ctn.
3/8" to 5/8"
3/4" to 1-1/4"
1
1
10
10
Drivers for Threaded Rod Couplers - SPLINE
Chem-Stud®
Cat. No.
Std. Box
Drill Dia.
Length
Std. Box
Std. Ctn.
7/16"
9/16"
11/16"
3-1/2"
4-1/4"
5"
10
10
10
500
200
200
Cat. No.
Hex Size
6580
6582
1/4"
3/8"
Fits Coupler Size
Std. Box
Std. Ctn.
3/8" to 5/8"
3/4" to 1-1/4"
1
1
10
10
Fits Coupler Size
Std. Box
Std. Ctn.
3/8" to 5/8"
3/4" to 1-1/4"
1
1
10
10
Drivers for Threaded Rod Couplers - SDS-MAX
Cat. No.
Hex Size
6559
6561
1/4"
3/8"
37
ADHESI VE
HAMMER-CAPSULE • Adhesive installation accessories
Reinforcing Bar Installation Tools
Anchor Seal Plugs help retain the adhesive in the anchor hole and hold the
anchor rod centered in the hole until the adhesive sets. The plugs are described by
the anchor rod diameter they are used with.
Chem-Stud Rebar Couplers and Drivers
Cat. No.
Size
6533
6534
6536
6537
6538
6539
6540
6590
6596
#3 Coupler
#4 Coupler
#6 Coupler
#7 Coupler
#8 Coupler
#9 Coupler
#10 Coupler
Spline Driver Extension
SDS-Max Driver Extension
Std. Box
Std. Ctn.
1
1
1
1
1
1
1
1
1
10
5
10
10
10
10
1
1
1
Size
6862
6863
6864
6865
3/8"
1/2"
5/8"
3/4"
Cat. No.
Description
7936
7937
3/8" Anchor Seal Plug
1/2" Anchor Seal Plug
Plug Depth
Hole Size
Std. Bag
3/8"
1/2"
7/16"
9/16"
25
25
ANSI Drill DIA.
ROD SIZE
Std. Bag
Std. CTN.
9/16"
11/16"
3/4"
7/8"
1"
1-1/8" Plug
1-3/8" Plug
1-1/2" Plug
1/2"/ #4
5/8" / #5
5/8" / #5
#6 - 3/4"
#7 - 7/8"
#8 - 1"
#9 - 1-1/4"
#10
10
10
10
10
10
10
10
10
100
100
100
100
100
100
100
100
For additional sizes call for availability.
Adhesive Pistons
Internally Threaded Insert Tools*
CAT. No.
Anchor Seal Plugs
Std. Box
Std. Ctn.
1
1
1
1
1
1
1
1
*Use with drivers for threaded rod.
Hammer-Capsule®
Drive-In Type Capsule Adhesive
tested to
The Hammer-Capsule System consists of a self contained, single use, two-part
glass capsule into which threaded anchor rod or reinforcing bars can be directly
driven without the need for a chisel point or spinning action. It is designed for
use in the installation of 3/8” through 1” diameter threaded rod in solid concrete and masonry materials. It can also be used to install reinforcing bars.
Hammer-Capsule Selection Guide
Cat. No.
Size
Drill Dia.
capsule length
Std. Box
Std. Ctn.
6702
6703
6704
6705
6706
6707
3/8"
1/2"
5/8"
3/4"
7/8"
1"
7/16"
9/16"
11/16"
7/8"
1"
1-1/8"
3-1/2"
4-1/4"
5"
6-5/8"
7"
8-1/4"
10
10
10
5
5
5
500
200
100
50
50
50
Adhesive Installation Accessories
Adhesive installation accessories are designed to provide a dispenser or mixing
nozzle extension when required and to aid in the preparation of the anchor hole.
Accessories
Description
8280
7931
7932
7933
7934
7935
Blow Out Pump
1/2" X 8-1/2" Nylon Brush
3/4" X 8-1/2" Nylon Brush
1" X 12" Nylon Brush
1-1/4" X 13" Nylon Brush
1-1/2" X 13-1/2" Nylon Brush
Description
08302
08258
08259
08300
08301
08303
08305
08309
9/16" Plug
11/16" Plug
3/4" Plug
7/8" Plug
1" Plug
1-1/8" Plug
1-3/8" Plug
1-1/2" Plug
Screen tubes are made from a 300 series stainless steel. The nominal diameter
of the screen listed indicates the matching rod diameter.
ICC-ES AC58
Cat. No.
Cat. No.
Std. Bag
1
1
1
1
1
1
Stainless Steel Screen Tubes
Cat. No.
Description
7960
7862
7864
7866*
7856
7961
7962
7963
7964
7959
7857
7965
7966
7967
7968
7858
7969
7970
7971
7972
7859
7973
7977
7974
7975
7860
7855
7865
7867
7869
7955
1/4" x 2" Screen Tube
1/4" x 6" Screen Tube †
3/8" x 3-1/2" Screen Tube †
1/2" x 3-1/2" Screen Tube
5/8” x 10" Screen Tube †
3/4” x 6" Screen Tube
Adhesive Shear Tube (steel sleeve)
drill dia.
Std.Ctn.
3/8"
3/8"
3/8"
3/8"
1/2"
1/2"
1/2"
1/2"
1/2"
1/2"
5/8"
5/8"
5/8"
5/8"
5/8"
3/4"
3/4"
3/4"
3/4"
3/4"
7/8"
7/8"
7/8"
7/8"
7/8"
1"
1"
1"
1"
1"
-
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
20
20
20
20
25
10
10
107
10
25
25
10
10
10
10
* Discontinued item once current stock exhausted. † Includes extension tubing
38
Adhesive installation accessories • POWERFOAM • TRIGGERFOAM
Description
8470
8473
8310
8311
8313
8315
8317
8321
8323
5/8" x 8" Anchor Rod
Std. CTN.
20
10
10
Rod is pre-bent at a 22-1/2 degree angle and includes nuts and washers.
Bent Threaded Rod (22-1/2°)
Plastic Screen Tubes
Cat/ No.
Description
7990
7993
7994
Drill DIA.
STD. box
1/2"
9/16"
9/16"
9/16"
9/16"
3/4"
3/4"
7/8"
1"
25
25
25
25
25
25
25
25
10
Cat. No.
Description
7957*
3/4" x 21" 22-1/2° Bent Rod
Std. CTN.
10
ADHESI VE
The nominal diameter of the screen listed indicate the matching rod diameter.
Note: hole size required for plastic screen tubes are different than that for the
stainless steel tubes.
Cat. No.
PowerFoam™
Expanding Polyurethane Foam
Base Material
Concrete, Masonry, Wood, Metal
8284
8285
8286
Size Range
12 oz. & 29 oz.
8287
8288
8290
8291
8283
8296
8482
8292
8465
8466
Material
8289
Polyurethane
PowerFoam is a one-part polyurethane expanding foam that sets and cures
into its final form by reacting to moisture and humidity present in the air.
PowerFoam’s exceptional ability to bond allows it to be applied to various
building elements including the surfaces of concrete, brick, block, wood, steel,
aluminum and other miscellaneous metals. As it is being dispensed, PowerFoam
has a neutral odor. Cured foam is standard yellow.
PowerFoam
8280
Cat. No.
Description
08130N
08132N
PowerFoam 12 oz.
PowerFoam 29 oz.
Std. Box
Std. Ctn.
Std. Pallet
12
12
12
12
1152
612
52073
Cat. No.
Description
Length Inches
Std. Pkg.
08284
08285
08275
08286
08278
08287
08288
08289
08290
08291
08283
08296
08282
08280
08292
08465
08466
6-3/4"
6-3/4"
6-3/4"
7-7/8"
7-7/8"
7-7/8"
11-7/8"
11-7/8"
11-7/8"
11-7/8"
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
52073
Straight Cut Threaded Rod
Description
7980
7985
7986
7989
1/2" x 5-1/2" Anchor Rod
5/8" x 6-1/2" Anchor Rod
ICC-ES AC58
Code listed
ICC-ES ESR-3263
FireBlock
TriggerFoam™ Pro
Expanding Polyurethane Foam
Base Material
Concrete, Masonry, Wood, Metal
Size Range
29 oz.
Material
Polyurethane
1
Straight cut rod is provided in A307 Threaded Anchor rod, zinc plated (astm b
633, clear chromate); includes nuts & washers.
Cat. No.
tested to
Std. CTN.
25
25
25
20
TriggerFoam Pro formulas are a professional, gun applied, normal expansion
polyurethane foam sealant with an extended temperature range which allows
for use at temperatures as low as 23° F (-5°C). It is designed to seal gaps,
insulate, and deaden sound. Recommended for use in heating and air
conditioning, electrical and plumbing applications.
Triggerfoam Pro
Cat. No.
Description
08136N
08133P
08134P
08135P
TriggerFoam Pro Standard Formula
TriggerFoam Pro Fire Block Formula
TriggerFoam Pro Window & Door Formula
TriggerFoam Pro All Season Formula
Std. Ctn.
12
12
12
12
39
ADHESI VE
POWERSTICK • POWERPATCH
08128
08139
08147
triggerFoam Tools & Accessories
Cat. No.
Description
08126
08128
08139
08147
TriggerFoam Pro 20" dispensing tool (not shown)
TriggerFoam Pro deluxe metal gun
TriggerFoam Pro plastic gun
TriggerFoam Pro Cleaner 17 fl. oz.
Std. Box
Std. Ctn.
1
1
1
6
10
10
10
-
PowerStick™
Adhesive Sealant
Base Material
Concrete, Masonry, Metals, Wood, Plastics
Size Range
10 oz. tubes
Material
MS Polymer Chemistry
PowerStick is a one-component universal adhesive/sealant based on proprietary
MS Polymer chemistry. PowerStick is the first professional grade product on the
market that delivers high bond strength and superior flexibility.
Powerstick
Cat. No.
Size
8166N
8168N
10 oz.
10 oz.
Color
Dispenser
Std. Box
STD. Ctn.
White
Gray
Caulk Gun
Caulk Gun
12
12
12
12
Std. box
Std. Ctn.
1
1
12
1
8437
8479
Caulking Guns for PowerStick
Cat.No.
Description
8437
8479
Manual Caulking Gun
High Performance Manual Tool
PowerPatch Kit™
Adhesive Sealant
Base Material
Concrete
Size Range
5 Gallon Bucket
PowerPatch is a rapid setting, 100% solids, high strength, all temperature
spall repair and patching material. PowerPatch uses a unique hybridized epoxy
urethane system and an engineered aggregate blend for superior performance
in all conditions, including high traffic areas.
40
Cat. No.
Size
8350
5 Gallon Bucket
Color
Std. Box
STD. Ctn.
Dark Gray
1
-
SELECTION GUIDE
• • • • • • • • • •
•
Polly
43
•
• •
• • •
•
Legs
43
•
• • •
Zip-All
44
• •
• • •
Sharkie
44
Strap-Toggle
44
Zip-It / Zinc Zip-It
44
•
• • •
Zip-Toggle
45
•
•
Poly-Toggle
45
Pop-Toggle
45
Bantam Plug
45
•
Fluted Plastic
45
•
• • • •
•
•
•
•
• •
• • • • •
•
• •
•
•
•
• • • • • • • • • •
•
• • •
•
• •
• • •
•
•
•
• •
•
•
• •
• • • • • •
•
•
• •
• • • • • • •
•
• • • • • • • •
•
• • •
•
• • • • • • • • •
Lead
• •
• •
Nylon Plastic
•
1/2"
42
• • •
3/8"
Toggle-Bolt
• • •
•
5/16"
•
1/4"
42
• •
3/16"
Scru-Lead
• • •
1/8"
•
Stone
42
Zamac Alloy
Coated / Plated Carbon Steel
Removable
Mushroom Head
Round Head
Finished (Hex) Head
No. 18 Screw
No. 16 Screw
No. 14 Screw
No. 12 Screw
No. 10 Screw
No. 9 Screw
No. 8 Screw
No. 7 Screw
No. 6 Screw
No. 5 Screw
No. 4 Screw
Wallboard / Plaster
Plywood
Hollow Brick
Solid Brick
Hollow Core Plank
Concrete
Page
Wall Dog
ANCHORS
Metal Anchors
Coating/
Material
Head Style
DUTY
Plastic Anhors
Anchor Diameter
L I GHT
Base Material
•
• Suitable
May be Suitable
41
ANCHORS
WALL DOG • SCRU-LEAD • TOGGLE BOLT
Wall Dog®
Universal Light-Duty Anchor
Base Material
Wallboard (1/2", 5/8" & double wallboard), Plywood,
Concrete, Hollow or Grout Filled Block, Brick, Plaster,
Wood and Masonry
Cat. No.
Description
2274
2275
2276
2286
2294
1-1/2" Bronze Pan Head
1-1/2" Zinc Pan Head
1-1/2" Black Phosphate Pan Head
1-1/4" Black Pan Head
1-1/4" Brass Pan Head
Std. Box
Std. Ctn. Master Ctn.
100
100
100
100
100
600
600
600
500
500
N/A
N/A
N/A
N/A
N/A
Size Range
3/16" Diameter x 2-1/2" Length max.
Anchor Material
L I G HT
DUTY
Case Hardened Carbon Steel
Powers' Wall Dog is the industry’s first all steel one-piece screw anchor,
featuring high-profile threads for easy fastening into wallboard & other masonry
base materials. Its deep cutting, corkscrew-like threads provide for smooth
entry and a strong hold. When removed, the Wall Dog leaves a much smaller
hole than toggles or other systems. For fastening into wallboard or wood, no
pre-drilling is required. Fastening into concrete, hollow or grout filled block, brick
and plaster requires a pre-drilled 3/16” ANSI hole.
Features and Benefits
• Installs in wallboard, plywood, concrete, hollow or grout filled block,
brick and plaster
• Patented design provides for smooth entry, clean cutting and a strong hold
• Thread design prevents spinning and stripping
• Heat treated point can penetrate metal and wood studs
• Various head styles and colors available
• Self-drills in wallboard and in plywood
• Installs quickly and easily with a Phillips® screwdriver
Wall-Dog KIT (Screwdriver)
Packaged with 50 zinc panhead anchors and 1 Phillips® screwdriver
Cat. No.
Description
Std. Box
Std. Ctn.
Wall-Dog Kit with Screwdriver
1
10
Packaged with 50 zinc panhead anchors and 3/16” straight shank bit
Cat. No.
Description
Std. Box
Std. Ctn.
1
10
2289
Wall-Dog KIT (Bit)
2332
Wall-Dog Kit with Drill Bit
Scru-Lead
Wall Anchor
Base Material
Size Range
No. 6-8 x 3/4" to No. 16-18 x 1-1/2"
Anchor Material
Lead Alloy
Wall-Dog LIGHT DUTY ANCHOR - Combo HWH
Cat. No.
Description
2265
2271
1-1/4" Combo HWH Zinc
1-1/4" Combo HWH Zinc
Std. Box
100
5000
N/A
1000
Wall-Dog LIGHT DUTY ANCHOR - wafer head
Cat. No.
Description
2277
2278
2279
2280
1/4" x 1-1/2" White Wafer Head
1/4" x 2" White Wafer Head
Std. Box
100
100
100
100
500
500
500
500
N/A
N/A
N/A
N/A
The Scru-Lead anchor is designed for use with sheet metal or wood screws in
concrete, block or brick. Made entirely of lead alloy which is soft enough for easy
installation, yet hard enough to give holding strength, the performance of this
product is dependent on the integrity of the base material.
Cat. No.
Size
9409
9414
9419
9429
9439
9460
6-8 x 3/4"
6-8 x 1"
6-8 x 1-1/2"
10-14 x 1"
10-14 x 1-1/2"
16-18 x 1-1/2"
Drill Dia.
Min. Depth
Std. Box
Std. Ctn.
1/4"
1/4"
1/4"
5/16"
5/16”
3/8"
3/4"
1"
1-1/2"
1"
1-1/2"
1-1/2"
100
100
100
100
100
25
1000
1000
500
500
500
250
Phillips® is a registered trademark of Phillips Consumer Electronics Corporation.
Toggle Bolt
Hollow Wall Anchor
Base Material
Wall-Dog LIGHT DUTY ANCHOR - robertson head
Cat. No.
Description
2281
2266
1-1/4" Zinc Robertson Head
1-1/4" Zinc Robertson Head
Std. Box
100
5000
N/A
1000
Hollow Block, Wallboard, Plaster
Size Range
1/8"x 2" to 1/2" x 4"
Anchor Material
Carbon Steel
Wall-Dog LIGHT DUTY ANCHOR - oval head
Cat. No.
Description
2314
2328
2288
2292
1-1/4" Zinc Oval Head
1-1/4" White Oval Head
1-1/4" Black Oval Head
1-1/4" Brass Oval Head
Std. Box
100
100
100
100
1000
1000
500
500
N/A
N/A
N/A
N/A
The Toggle Bolt is a spring wing type hollow wall anchor designed for use in
block, wallboard and other hollow base materials. A two-part assembly consisting of a machine screw and a spring wing toggle,sizes range from 1/8” x 2” to
1/2” x 4” with combo round, flat, mushroom, tie-wire or slotted hex head styles.
Wall-Dog LIGHT DUTY ANCHOR - Pan head
42
Cat. No.
Description
2316
2330
2273
1-1/4" Zinc Pan Head
1-1/4" White Pan Head
1-1/2" White Pan Head
Std. Box
100
100
100
1000
1000
600
N/A
N/A
N/A
Combo MUSHROOM HEAD
Cat. NO.
Size
4023
4033
1/8" x 2"
1/8" x 3"
Drill Dia.
Std. Box
Std. Ctn.
3/8"
3/8"
50
50
500
500
POLLY • LEGS
Size
4043
4133
4143
4233
4243
1/8" x 4"
3/16" x 3"
3/16" x 4"
1/4" x 3"
1/4" x 4"
Drill Dia.
Std. Box
Std. Ctn.
3/8"
1/2"
1/2"
5/8"
5/8"
50
50
50
50
50
500
500
500
500
500
Polly
L I GHT
Cat. NO.
Hollow Wall Anchor
Base Material
Plaster, Wallboard, Block, Hollow Tile, Plywood
Size Range
1/8" extra short to 1/4" long
Carbon Steel
The Polly is a sleeve type hollow wall anchor designed for use in base materials
such as plaster, wallboard, concrete block, hollow tile or plywood.
Cat. NO.
Size
4038
1/8" x 3"
Drill Dia.
Std. Box
Std. Ctn.
3/8"
50
500
Combination Slotted Phillips Head Polly
Combo ROUND HEAD
Cat. NO.
Size
Drill Dia.
Std. Box
Std. Ctn.
4021
4031
4041
4121
4131
4141
4151
4161
4231
4241
4251
4261
4341
4431
4441
4451
4461
4541
1/8" x 2"
1/8" x 3"
1/8" x 4"
3/16" x 2"
3/16" x 3"
3/16" x 4"
3/16" x 5"
3/16" x 6"
1/4" x 3"
1/4" x 4"
1/4" x 5"
1/4" x 6"
5/16" x 4"
3/8" x 3"
3/8" x 4"
3/8" x 5"
3/8" x 6"
1/2" x 4"
3/8"
3/8"
3/8"
1/2"
1/2"
1/2"
1/2"
1/2"
5/8"
5/8"
5/8"
5/8"
7/8"
7/8"
7/8"
7/8"
7/8"
1-1/4"
50
50
50
50
50
50
50
50
50
50
50
50
25
25
25
25
25
25
500
500
500
500
500
500
500
500
500
500
500
500
250
250
250
125
125
25
Cat. No.
Size
2100
2101
2102
2111
2112
2113
2121
2122
1/8" XS
1/8" S
1/8" L
3/16" S
3/16" L
3/16" XL
1/4" S
1/4" L
Screw Length
Drill Dia.
Wall Thickness
Std. Box
Std. Ctn.
1-1/16"
1-3/4"
2-1/4"
2"
2-1/2"
3"
2-1/4"
2-3/4"
5/16"
5/16"
5/16"
3/8"
3/8"
3/8"
7/16"
7/16"
1/8"–1/4"
3/8"–1/2"
5/8"–1"
3/8"–5/8"
3/4"–1-1/8"
1-1/4"–1-3/4"
3/8"–1/2"
5/8"–1-1/8"
100
100
100
50
50
25
50
50
500
500
500
250
250
125
250
250
ANCHORS
SLOTTED HEX HEAD
DUTY
Anchor Material
XS - Extra Short S - Short L - Long XL - Extra Long
Slotted Hex Head Polly
Cat. No.
Size
2105
1/8" S
Screw Length
1-3/4"
Drill Dia. Wall Thickness
5/16"
Std. Box
Std. Ctn.
100
500
3/8"–1/2"
Drive Polly
Cat. No.
Size
2180*
2182
2184
1/8" XS
1/8" S
1/8" L
Screw Length
Wall Thickness
Std. Box
Std. Ctn.
1-3/8"
2"
2-3/8"
1/8"–1/4"
3/8"–1/2"
1/2"–3/4"
100
100
100
500
500
500
* Discontinued item once current stock exhausted. XS - Extra Short S - Short L - Long
Polly Setting Tool (Fits all sizes)
Cat. No.
DESCRIPTION
2150
Polly Setting Tool
Std. Box
Std. Ctn.
1
1
FLAT HEAD
Cat. NO.
Size
4132
4142
4232
3/16" x 3"
3/16" x 4"
1/4" x 3"
Drill Dia.
Std. Box
Std. Ctn.
1/2"
1/2"
5/8"
50
50
50
500
500
500
Legs
Wallboard Anchor
Toggle Wings Only
Cat. NO.
Size
Drill Dia.
Std. Box
Std. Ctn.
4000
4020
4220
4330
4430
4540
1/8"
3/16"
1/4"
5/16"
3/8"
1/2"
3/8"
1/2"
5/8"
7/8"
7/8"
1-1/4"
100
100
100
50
50
25
500
1000
1000
500
500
25
Base Material
Wallboard
Size Range
Use with No. 6 or No. 8 screw
Anchor Material
Carbon Steel
The Legs anchor is a fast, easy to use expansion anchor designed for use in wallboard.
The anchor has a pierce point, requiring no pre-drilling. Removal of the anchor, if
required, is easy. Once removed, the anchor leaves a small slit in the wallboard.
Legs Wallboard Anchor
Tie-Wire Acoustical Toggle
Cat. No.
Size
4247
4257
1/4" x 4"
1/4" x 5"
Tie Wire Hole Size
Drill Dia.
Std. Box
Std. Ctn.
7/32"
7/32"
5/8"
5/8"
100
100
100
100
Cat.No.
Description
2336
2335
Legs Anchor w/ No.8 x 1" Screw
Master Pack
Cat. No.
Description
2338
Std. Box
Std. Ctn.
100
100
1000
1000
MASTER Ctn.
5000
Table Continues On Next Page
43
ANCHORS
ZIP-ALL • SHARKIE • STRAP TOGGLE
SELF DRLLING STRAP TOGGLE • ZIP-IT / ZIP-IT JR.
Cat. No.
Size
4056
4058
3/8" x 4"
1/2" x 4"
Drill Dia.
Wall Thickness
Std. Box
Std. Ctn.
3/4"
3/4"
2-1/2"
2-1/2"
25
25
150
150
Zip-All®
Wallboard Anchor
Base Material
Wallboard
`
New!
Size Range
L I G HT
DUTY
Anchor Material
Self Drilling Strap-Toggle
Zamac Alloy
Hollow Wall Anchor
The Zip-All anchor is a one piece self drilling anchor designed for use in hollow
gypsum wallboard, wood, block and concrete for light duty loads. It is available in
Zamac alloy for use with either a No. 6 or No. 8 screws in 3/8" to 1" wallboard.
Wall Thickness
2296
2297
3/8" to 1"
3/8" to 1"
Hollow Wallboard or Hollow Block
Size Range
3/16" x 4” to 1/4" x 4"
Anchor Material
ZiP-All
Cat. No.
Base Material
Description
Std. Box
Std. Ctn.
Zinc - no screws
Zinc - with screws
100
100
1000
1000
Plastic
The Self Drilling Strap-Toggle™ is a pre-assembled heavy duty hollow wall
anchor that can be easily adjusted to accommodate any wall thickness of up to
2-1/2.” The screw and fixture may be installed and removed as often as necessary. No pre-drilling required in drywall.
SEF DRILLING Strap-Toggle
Cat. No.
Sharkie
Size
PFM4561500 3/16"
PFM4561600 1/4"
Plastic Wall Anchor
Base Material
Std. Box
Std. Ctn.
50
50
300
300
Zip-It® and Zip-It® Jr.
Concrete, Block, Brick & Wallboard
Size Range
Wallboard Anchor
Use with No. 4 x 1" to No. 14 x 1-9/16" screw
Base Material
Anchor Material
Wallboard
Plastic
Size Range
The Sharkie is a one-piece plastic anchor designed for light duty applications
in wallboard, concrete and masonry. The Sharkie works in hollow or solid base
materials and is suitable for screws with various thread sizes and styles. Screws
for the anchor may be installed with a screw gun. The Sharkie is available with
and without a flange at the top of the anchor to match the application.
Sharkie Drywall Anchor
Cat. No.
Description
7580
7582
7584
Sharkie Anchor Flange #4-#10
Std. Box
Std. Ctn.
100
100
100
1000
1000
500
Anchor Material
Engineered Nylon or Zamac Alloy
The Zip-It anchor is a one piece self drilling anchor designed for use in hollow
gypsum wallboard for light duty loads. It is available in both engineered nylon
and Zamac alloy for use with either a No. 6 or No. 8 screws in 3/8" to
1" wallboard. The Zip-It Jr. is formed from engineered nylon for use with
No. 6 screws in 3/8" to 5/8" wallboard.
Nylon ZiP-It
Strap-Toggle™
Cat. No.
Wall Thickness
Description
2345
2348
2355
3/8" to 1"
3/8" to 1"
3/8" to 1"
Std. box, no screws
Std. box, No.8 x 1" screws
Master ctn., no screws
Std. Box
Std. Ctn.
100
100
-
1000
1000
5000
Hollow Wall Anchor
Base Material
Hollow Wallboard or Hollow Block
Size Range
3/16" x 4” to 1/2" x 4"
Zinc ZiP-It
Anchor Material
Plastic
The Strap-Toggle is a pre-assembled anchor consisting of a carbon steel wing
and a locking cap / ratchet leg assembly molded from engineered plastic. When
compared to traditional toggles, this unique anchor can be installed through a
smaller hole and does not require a fixture or screw to set in the base material.
Strap-Toggle
44
Cat. No.
Size
4052
4054
3/16" x 4"
1/4" x 4"
Drill Dia.
Wall Thickness
Std. Box
Std. Ctn.
1/2"
1/2"
2-1/2"
2-1/2"
50
50
300
300
Cat. No.
Wall Thickness
Description
2346Z
2349Z
2356Z
3/8" to 1"
3/8" to 1"
3/8" to 1"
Std. box, no screws
Std. box, No.8 x 1" screws
Master ctn., no screws
Std. Box
Std. Ctn.
100
100
-
1000
1000
1000
ZiP-It Kits
Cat. No.
Material
Description
2368
Nylon
50 anchors & No. 8 x 1" screws
Std. Box
Std. Ctn.
1
10
ZINC ZIP-TOGGLE • POLY-TOGGLE • POP• TOGGLE
BANTAM • FLUTED PLASTIC ANCHOR
L I GHT
NYLON ZiP-It Jr.
Cat. No.
Wall Thickness
Description
2350
2351
3/8"-5/8"
3/8"-5/8"
Std. box (no screws)
Std. box & No. 6 x 1" screws
Std. Box
Std. Ctn.
100
100
1000
1000
Pop-Toggle
Hollow Wall Anchor
DUTY
Base Material
Gypsum Wallboard, Plaster, Plywood & some Hollow Masonry
Size Range
Wall thickness from 1/8" to 5/8", No. 6 to No. 10 wood or sheet metal screws
ZINC ZiP-It Jr.
Wall Thickness
Description
2362Z
2364Z
2363Z
3/8"-5/8"
3/8"-5/8"
3/8"-5/8"
Std. box (no screws)
Std. box & No. 6 x 1" screws
Master ctn. (No screws)
Std. Box
Std. Ctn.
100
100
-
1000
1000
5000
Std. Box
Std. Ctn.
1
10
ZiP-It Jr. Kits
Cat. No.
Material
Description
2367
Nylon
50 Anchors, No. 6 x 1" screws and
No. 2 Phillips Driver Bit
Anchor Material
Plastic
Pop-Toggle fasteners are hollow wall anchors ideal for static applications
requiring light duty performance. Installation is easy, needing a pre-drilled
5/16” diameter hole. The fastener pre-installs without a screw, allowing for easy
placement and removal of the fixture.
Cat. No.
Description
4060
4062
4064
Pop-Toggle Small
Pop-Toggle Medium
Pop-Toggle Large
Std. Box
Std. Ctn.
100
100
100
1000
1000
1000
ANCHORS
Cat. No.
Zinc Zip-Toggle®
Hollow Wall Anchor
Bantam Plug
Base Material
Wallboard
Plastic Wall Anchor
Size Range
Base Material
Use with No. 6 x 2" screw
Concrete, Block, Brick, Wallboard
Anchor Material
Size Range
Zamac Alloy
No. 6-8 x 3/4" to No. 14-16 x 1-1/2"
The Zip-Toggle is a hollow gypsum wallboard anchor designed to provide
superior performance without the need to pre-drill larger diameter holes. The
Zip-Toggle is packaged with its own No. 6 x 2" lubricated screw for 3/8" to
5/8" wallboard.
The Bantam Plug anchor is a plastic anchor designed for use with lightweight
fixtures with a sheet metal or wood screw.
Cat. No.
Size
2295
Metal Zip-Toggle with screws
Anchor Material
Plastic
Screws
Std. Box
Std. Ctn.
Cat. No.
Size
No. 6 x 2"
50
250
7559
7569
7579
7589
6-8 x 3/4"
8-10 x 7/8"
10-12 x 1"
14-16 x 1-1/2"
Drill Dia.
Min. Depth
Std. Box
Std. Ctn.
Mstr. Ctn.
3/16"
3/16"
1/4"
5/16"
3/4"
7/8"
1"
1-1/2"
100
100
100
50
1000
1000
1000
500
150,000
150,000
80,000
40,000
Kits - Slotted/Phillips Pan Head Sheet Metal Screws
Poly-Toggle®
Plastic Hollow Wall Anchor
Cat. No.
Kit No.
8934
8936
8938
B-8
B-10
B-12
Anchor Size
Screw Size
Min. Depth
8-10 No. 8 x 1"
10-12 No. 10 x 1"
10-12 No. 12 x 1"
7/8"
1"
1"
Anchor & Screws Std Ctn.
100
100
100
10
10
10
100 Anchors and screws plus one drill bit per kit. For additional kits see page 93.
Base Material
Wallboard or Solid Masonry
Size Range
1/8" to 5/8" Wall Thickness
Fluted Plastic Anchor
Anchor Material
Plastic Wall Anchor
Plastic
The Poly-Toggle is a screw actuated hollow wall anchor for use in paneling,
wallboard and solid masonry available in 4 sizes to match the most common wall
thicknesses. In solid base materials, the anchor can be used by removing the outer
wings. The performance of this product depends on the integrity of the base
material in which it is installed.
Cat. No.
Size
2302
2303
2304
2305
Mini
Short
Medium
Long
WALL THICKNESS
Drill Dia.
Std. Box
Std. Ctn.
1/8"
3/8"
1/2"
5/8"
5/16"
5/16"
5/16"
5/16"
100
100
100
100
1000
1000
1000
1000
Base Material
Size Range
No. 4-6 x 1" to No. 14 x 1-1/2"
Anchor Material
Plastic
The Fluted Plastic Anchor is designed for light duty fastening applications with
sheet metal or wood screws. Longitudinal ribs on the anchor body prevent it
from turning during tightening of the screw. This standard plastic screw anchor
comes color-coded by diameter for easy application.
Cat. No.
Size
7500
7510
7515
7520
7530
4-6 x 1"
10-12 x 1"
10-12 x 1-1/4"
10-12 x 1-1/2"
14 x 1-1/2"
Color
Drill Dia.
Min. Depth
Std. Box
Std. Ctn.
White
Green
Green
Green
Blue
3/16"
1/4"
1/4"
1/4"
5/16"
1"
1"
1-1/4"
1-1/2"
1-1/2"
100
100
100
100
100
1000
1000
1000
1000
1000
45
Page
Shank Length
Shank Diameter
47
1/2" to
1-1/2"
0.145"
.300 Head Pin
to 0.145" • •
47 1-3/4"
3"
.300 Head Pin w Top Hat
47
1/2" to
1"
0.145"
• •
• •
.300 Head Pin w Washer
47
3/4" to
1-1/2"
0.145"
.300 Head Pin w Washer
47
2" to
3"
0.145"
.300 Head Step Shank
47
3/4" to
1"
0.145"/ •
0.130"
8mm Head Pin
48
5/8" to
1-1/2"
0.145"
8mm Head Pin
to 0.145" • •
48 1-5/8"
2-7/8"
8mm Head Pin w
Top Hat
48
5/8" to
1"
0.145"
• •
• •
• • • •
8mm Head CSI Pins
48
1/2" to
2-7/8"
0.157"
• •
• •
•
•
• •
8mm Head .0157
CSI Pin w Washer
48
3/4" to
2-7/8"
0.157"
• •
• •
•
•
• •
8mm Head Pin w Washer
48
1" to
1-1/2"
0.145"
• •
• •
• • • •
• • • •
• •
8mm Head Pin w Washer
48
2" to
2-7/8"
0.145"
• •
•
•
•
•
1/4"-20 Threaded Stud
49
1/2" to
1-1/4"
0.145"
• •
• •
49
3/4" to
1-1/4"
0.205"
• •
•
Hammer Drive Pin
49
3/4" to
3"
0.140"
• •
(.300", 8mm)
49
1" to
1-1/4"
0.145"
0.157"
•
BX-EMT Conduit Clip
Assemblies (.300", 8mm)
50
1" to
1-1/4"
0.145"
• • •
Rebar Basket Clip
Assemblies (8mm)
0.145" • •
50 2-7/16",
2-7/8"
• • • •
• • • •
•
• • •
•
•
•
•
• •
• • • •
• • • •
•
• • • • •
• • • •
• • • •
• •
•
•
•
• •
• • • •
•
• • • • •
• • • •
• Suitable
May be Suitable
• • • •
•
ICC-ES ESR-2024
LARR-25304
•
•
• •
•
• •
•
ICC-ES ESR-2024
LARR-25304
• •
•
• •
•
• • • •
•
• • • • •
•
• • • •
•
• • • •
• •
ICC-ES ESR-2024
LARR-25304
•
•
• •
•
• •
•
ICC-ES ESR-2024
LARR-25304
• • • •
•
• • •
•
• • • •
•
ICC-ES ESR-2024
LARR-25304
•
•
• •
•
•
• •
•
ICC-ES ESR-1995
LARR-25931
•
•
• •
•
•
• •
•
ICC-ES ESR-1995
LARR-25931
•
ICC-ES ESR-2024
LARR-25304
•
•
•
•
•
•
•
• • • • • •
•
•
• • •
•
•
•
•
• • • •
•
•
•
ICC-ES ESR-2024
LARR-25304
•
•
ICC-ES ESR-2024
LARR-25304
ICC-ES ESR-2024
LARR-25304
• • • •
• • • • •
• • • • • •
• •
• • •
•
• • • •
• • • • •
• • • • • •
• •
• •
•
•
•
• •
•
• •
•
• • •
DX460
DX100/DX200
DXA41
DXA40
DX451
DX450
DX350/DX351/DX36M
DX35
•
DX600N
•
DX400
Viper
Cobra
SA270
•
MD380
•
DXE72
•
DX E37
•
• •
Other Tools
•
•
•
•
•
•
•
ICC-ES ESR-2024
LARR-25304
• •
• •
•
•
•
•
•
•
•
• •
• • • •
• •
•
• • •
D60/D60L
55
•
D45
.27 Caliber 10 Load Strip
• • • •
LADD (L1600)
55
•
M70
.27 Caliber Safety Strip
ICC-ES ESR-2024
LARR-25304
721
55
•
Sniper
.25 Caliber 10 Load Strip
• • • •
PA351
55
•
P3600
.27 Caliber Single Load
Long Loads
ICC-ES ESR-2024
LARR-25304
• • •
•
P3801
55
•
ICC-ES ESR-2024
LARR-25304
• • • •
P3500/PA3500
.22 Caliber Single Load
Ladd Tool (L1600)
•
•
•
P7201
•
• •
• •
•
P35s
Yellow–Level 4
•
•
P2201
Green–PLevel 3
•
•
T1000
Brown–Level 2
•
•
•
Code
Recognition
•
•
Powers Tools
Purple/Black Level 6
Gray–Level 1
55
•
P1000
0.300" Head Drive Pins
Specialty Threaded Studs
Clips & Assemblies
• • • • •
Red–Power Level 5
Page
.22 Caliber
"A"Single Load
Loads
Powder Actuated Loads
Other Tools
.300 Head Pin
Pins
Load Power
46
Powers Tools
Concrete
Grout-filled CMU
Steel
P1000
T1000
P2201
P35s
P7201
P3500/PA3500
P3801
P3600
PA351
P60
Sniper
721
M70
D45
D60/D60L
D45/D60/D60L
MD380
SA270
Cobra
Viper
DX E37
DXE72
DX400
DXE72/DX400
DX600N
DX35
DX350/DX351/DX36M
DX451
DXA40
DXA41
DX100/DX200
DX460
Dimensions Base
8mm Head Drive Pins
POW DER
ACTUATED
SELECTION GUIDE
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
.300 head pins
ICC-ES ESR-2024
.300 Head Drive Pins
Standard Pins
.300 Head Drive Pins with 7/8” washer
Shank Length
50090
50092
50094
50096
50098
50100
1"
1-1/4"
1-1/2"
2"
2-1/2"
3"
Head Dia.
Shank Dia.
Std. Box
Std. Ctn.
.300
.300
.300
.300
.300
.300
.145
.145
.145
.145
.145
.145
100
100
100
100
100
100
1000
1000
1000
1000
1000
1000
.300 Head Drive Pins
Cat. No.
Shank Length
50012
50016
50022
50023
50026
50032
50034
50038
50040
50044
50048
1/2" (knurled)
5/8" (knurled)
3/4"
3/4” Black
1"
1-1/4"
1-1/2"
2"
2-1/4"
2-1/2"
3"
Head Dia.
Shank Dia.
Std. Box
Std. Ctn.
.300
.300
.300
.300
.300
.300
.300
.300
.300
.300
.300
.145
.145
.145
.145
.145
.145
.145
.145
.145
.145
.145
100
100
100
100
100
100
100
100
100
100
100
5000
5000
5000
5000
5000
1000
1000
1000
1000
1000
1000
The pins listed below are used primarily for applications fastening drywall track
to concrete or steel. They are assembled with a metal top hat to provide extra
bearing surface against the drywall track.
.300 Head Drive Pins with Top Hat
Cat. No.
Shank Length
50136
50138
50140
1/2" knurled
5/8" knurled
3/4"
Head Dia.
Shank Dia.
Std. Box
Std. Ctn.
.300
.300
.300
.145
.145
.145
100
100
100
5000
5000
5000
ACTUATED
Drive pins with a 0.300" diameter head are designed for permanently fastening
a fixture to concrete, some types of masonry and A36 structural steel. Drive pins
are manufactured with a 0.145" diameter shank in various lengths. Knurled
shank designs are available to increase performance in steel base materials.
A plastic flute is mounted over the point to retain the drive pin in the fastener
guide of the tool providing guidance during the driving operation.
Cat. No.
POW DER
Code listed
.300 Head Drive Pins with 1” washer
Cat. No.
Shank Length
50108
50110
50112
50114
50116
1-1/4"
1-1/2"
2"
2-1/2"
3"
Head Dia.
Shank Dia.
Std. Box
Std. Ctn.
.300
.300
.300
.300
.300
.145
.145
.145
.145
.145
100
100
100
100
100
1000
1000
1000
1000
1000
Powers ACQ Powder Actuated Fasteners are designed for
fastening through pressure treated lumber into concrete and
grout filled masonry. The fasteners are available with either a
round or square washer for increased pullover resistance.
.300 Head Drive Pins (mechanically galvanized)
Cat. No.
Shank Length
50034MG
50038MG
50045MG
50047MG
1-1/2"
2"
2-1/2"
3"
Head Dia.
Shank Dia.
Std. Box
Std. Ctn.
.300
.300
.300
.300
.145
.145
.145
.145
1000
1000
1000
1000
5000
5000
5000
5000
Washered Pins
.300 Head Drive Pins w/1” washer (mechanically galvanized)
Cat. No.
Shank Length
To provide resistance to pullover, these pins are available with pre-assembled
14 gage (0.075") metal washers in various diameters. The insulation washer
has a thickness of 0.035".
50110MG
50112MG
50113MG
50115MG
1-1/2"
2"
2-1/2"
3"
Head Dia.
Shank Dia.
Std. Box
Std. Ctn.
.300
.300
.300
.300
.145
.145
.145
.145
1000
1000
1000
1000
5000
5000
5000
5000
.300 Head Drive Pins with 3/4” washer
Cat. No.
Shank Length
50070
50080
3/4"
2-1/2"
Head Dia.
Shank Dia.
Std. Box
Std. Ctn.
.300
.300
.145
.145
100
100
1000
1000
47
POW DER
ACTUATED
8mm head pins • CSI pins
8mm Head Drive Pins
X-DN Type Pins 8mm Head Drive Pins
Cat. No.
Shank Length
50180
50182
50184
50186
50188
50190
50192
50194
50196
50198
50200
50202
16mm knurled - 5/8"
19mm knurled - 3 /4"
22mm - 7/8"
27mm - 1"
32mm - 1-1/4"
37mm - 1-1/2"
42mm - 1-5/8"
47mm - 1-7/8"
52mm - 2"
57mm - 2-1/4"
62mm - 2-1/2"
72mm - 2-7/8"
Head Dia.
Shank Dia.
Std. Box
Std. Ctn.
8mm
8mm
8mm
8mm
8mm
8mm
8mm
8mm
8mm
8mm
8mm
8mm
.145
.145
.145
.145
.145
.145
.145
.145
.145
.145
.145
.145
100
100
100
100
100
100
100
100
100
100
100
100
5000
5000
5000
5000
1000
1000
1000
1000
1000
1000
1000
1000
8mm Head Spiral CSI Drive Pins
With Washers
Competes with XU Pins For Concrete, Steel and I-Beams
Cat. No.
Shank Length
50245
50247
50249
50261
50263
50265
3/4" (19mm)
1" (27mm)
1-1/4" (32mm)
1-1/4" (32mm)
2-1/2" (62mm)
2-7/8" (72mm)
Head Dia.
Shank Dia.
Washer
Std. Box
Std. Ctn.
8mm
8mm
8mm
8mm
8mm
8mm
.157
.157
.157
.157
.157
.157
3/4"
3/4"
3/4"
1"
1"
1"
100
100
400
400
400
400
1,000
1,000
1,000
1,000
1,000
1,000
8mm Diameter Head Drive Pins with Top Hat
The pins listed below are used primarily for applications fastening drywall track
to concrete or steel. They are assembled with a metal top hat to provide extra
bearing surface against the drywall track.
8mm Head Collated Spiral CSI Drive Pins
8mm Spiral CSI 10 FASTENER MAGAZINE FOR PA 351 and DX460
Cat. No.
Shank Length
50450
50452
50454
50456
50458
50460
50461
50462*
5/8" (16mm) (K)
3/4" (19mm) (K)
7/8" (22mm) (K)
1" (27mm) (K)
1-1/4" (32mm) (K)
1-1/2" (37mm) (K)
1-5/8" (42mm) (K)
2" (52mm) (K)
8mm Diameter Head Drive Pins with Top Hat
Cat. No.
Shank Length
50210
50214
50216
16mm knurled - 5/8"
22mm - 7/8"
27mm - 1"
Head Dia.
Shank Dia.
Std. Box
Std. Ctn.
8mm
8mm
8mm
.145
.145
.145
100
100
100
5000
5000
5000
Washered Pins
K=Knurled
Head Dia.
Shank Dia.
Std. Box
Std. Ctn.
8mm
8mm
8mm
8mm
8mm
8mm
8mm
8mm
.157
.157
.157
.157
.157
.157
.157
.157
100
100
100
100
100
100
100
100
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
* DX460 Only
To provide resistance to pullover, these pins are available with preassembled
14 gage (0.075") metal washers in various diameters.
8mm Head Collated Drive Pins
8mm Head 10 FASTENER MAGAZINE FOR PA 351 and DX460
8mm Diameter Head Drive Pins with 1” Washer
Cat. No.
Shank Length
50220
50222
50224
50226
50228
27mm - 1"
32mm - 1-1/4
37mm - 1-1/2"
52mm - 2"
62mm - 2-1/2"
Head Dia.
Shank Dia.
Std. Box
Std. Ctn.
8mm
8mm
8mm
8mm
8mm
.145
.145
.145
.145
.145
100
100
100
100
100
1000
1000
1000
1000
1000
Code listed
ICC-ES ESR-2024
48
Shank Length
50197
50201
50203
50204
50205
50208
50207
50209
50241
50211
1/2" (13mm)
5/8" (16mm)
3/4" (19mm)
7/8" (22mm)
1" (27mm)
1-1/4" (32mm)
1-1/2" (37mm)
2" (52mm)
2-1/2" (62mm)
2-7/8" (72mm)
Shank Length (in.)
50240N
50242N
50244N
50246N
50248N
50250N
50252N
50254N
50256N
50258N
50260N
50262N
50264N
5/8" K
3/4" K
3/4"
7/8"
1"
1-1/4"
1-1/2"
1-5/8"
1-7/8"
2"
2-1/4"
2-1/2"
2-7/8"
K=Knurled
8mm Head Spiral CSI Drive Pins Cat. No.
Cat. No.
Head Dia.
Shank Dia.
Std. Box
Std. Ctn.
8mm
8mm
8mm
8mm
8mm
8mm
8mm
8mm
8mm
8mm
.157
.157
.157
.157
.157
.157
.157
.157
.157
.157
100
100
100
100
100
100
100
100
100
100
1000
1000
5000
5000
5000
1000
5000
1000
1000
1000
Shank Length (mm)
Head Dia.
Shank Dia.
Std. Box
Std. Ctn.
16
19
19
22
27
32
37
42
47
52
57
62
67
8mm
8mm
8mm
8mm
8mm
8mm
8mm
8mm
8mm
8mm
8mm
8mm
8mm
.145
.145
.145
.145
.145
.145
.145
.145
.145
.145
.145
.145
.145
500
500
500
500
500
500
500
500
500
500
500
500
500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
2500
THREADED STUDS • ASSEMBLIES & ACCESSORIES
Available in 1/4"-20 and 3/8"-16 thread diameters with a variety of thread and
shank lengths for concrete and A36 structural steel. Used for applications where
it may be desirable to remove the fixture, or where shimming may be required.
The shank diameter: 0.145" for the 1/4"-20; and 0.205" for the 3/8"-16.
Knurled shanks are available to increase performance in steel base materials. A
plastic flute is mounted over the point to retain the drive pin in the fastener guide
of the tool for guidance during the driving operation. On the 1/4"-20 threaded
studs, a plastic cap is also provided to protect the threads of the fastener during
the driving process.
Assemblies are combinations of drive pins and stamped steel clips designed
for specific applications. The pins are held within the clip using either a dome
mechanism or a metal top hat.
For applications suspending acoustical ceiling systems or light fixtures, several
styles of angled clips are pre-mounted onto pins.
1/4” -20 Threaded Studs
Cat. No.
Thread Length
50322
50326
50328
50330
50336
50338
3/4"
3/4"
1/2"
3/4"
3/4"
1-1/4"
SHANK Length
Thread Dia.
Shank Dia.
Std. Box
Std. Ctn.
1/2" K
3/4"
1"
1"
1-1/4"
1-1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
.145
.145
.145
.145
.145
.145
100
100
100
100
100
100
1000
1000
1000
1000
1000
1000
K=Knurled
Code listed
ICC-ES ESR-2024
ACTUATED
Assemblies & Accessories
POW DER
Threaded Studs
.300 Head Pins with Ceiling Clips
Cat. No.
Description
50364
50368†
50370
1"
1-1/8"
1-1/4"
† Economy Clip
Head Dia.
Shank Dia.
Wire Hole
Std. Box
Std. Ctn.
.300
.300
.300
.145
.145
.145
0.278"
0.278"
0.278"
100
100
100
1000
1000
1000
3/8” -16 Threaded Studs
Cat. No.
Thread Length
50340
50342
50344
1-1/4"
1-1/4"
1-1/4"
SHANK Length
Thread Dia.
Shank Dia.
Std. Box
Std. Ctn.
3/4" K
1"
1-1/4"
3/8"
3/8"
3/8"
.205
.205
.205
100
100
100
1000
1000
1000
K=Knurled
8mm Drive Head Pins with Ceiling Clips
Cat. No.
Description
Hammer Drive Pins
50272
50274
50206
27mm w/CC
32mm w/CC
1-1/4" w/CC
Head Dia.
Shank Dia.
Wire Hole
Std. Box
Std. Ctn.
8mm
8mm
8mm
.145
.145
.177
0.278"
0.278"
0.278"
100
100
100
1000
1000
1000
Hammer Drive pins are designed for permanently fastening a fixture to concrete
and some types of masonry. This fastener is designed for use in a standard
hand tool and should not be used in a powder actuated tool. The pins are
formed with a 1/4" diameter head on one end and a 0.140” diameter shank
in various lengths. A 3/8" diameter steel washer is mounted over the point to
retain the drive pin in the fastener guide of the tool providing guidance during
the driving operation.
ballistic point drive pin with ceiling clip
No Powder Loads Required
Shank Length
50058
50366
1-1/4" with ceiling clip (45˚)
7/8" with ceiling clip (90˚)
1/4” Head Hammer Drive Pins
Cat. No.
Shank Length
50294
50296
50298
3/4"
1"
1-1/4"
Cat. No.
Head Dia.
Shank Dia.
Std. Box
Std. Ctn.
1/4"
1/4"
1/4"
.140
.140
.140
100
100
100
5000
5000
1000
Std. Box
Std. Ctn.
1
1
head Dia.
Shank Dia.
Std. Box
Std. Ctn.
.300
.300
.181/.150
.181/.150
100
100
1000
1000
Pre-assembled Pin and Clip for LADD Tool (l1600)
Shank Length
50438
Pre-assembled pin clip
Cat. No.
head Dia.
Shank Dia.
Wire Hole
Std. Box
Std. Ctn.
.310
.155
0.278"
100
1000
Hammer Drive Setting Tool
Cat. No.
Description
50310
Hammer Drive Tool - Standard
49
ACTUATED
BX & EMT Conduit Clip Assemblies
POW DER
ASSEMBLIES AND ACCESSORIES
.300 Head DRIVE Pins with BX CABLE Clips
For the electrical trade, BX and EMT conduit clips are provided in various sizes
for attaching conduit to base materials.
8mm Head Spiral CSI Drive Pin with Ceiling clip
Description
50150
1" (BX) w/TH
Cat. No.
Head Dia.
Shank Dia.
Std. Box
Std. Ctn.
.300
.145
100
1000
Head Dia.
Shank Dia.
Std. Box
Std. Ctn.
.300
.300
.300
.300
.300
.145
.145
.145
.145
.145
100
100
100
100
25
1000
1000
1000
1000
250
Cat. No.
Description
50212
50213
50218
7/8" (22mm) CSI w/PW TH 90cc
1" (27mm) CSI w/PW TH 90cc
1-1/4" (32mm) CSI w/PW TH 90cc
Head Dia. Shank Dia. Wire Hole
8mm
8mm
8mm
Std. Box
Std. Ctn.
100
100
100
1000
1000
1000
Shank Dia.
Std. Box
Std. Ctn.
.145
.145
100
100
1000
1000
.157 0.313"
.157 0.313"
.157 0.313"
.300 head drive pin with Ceiling clip and post nut
.300 Head Drive Pins with EMT Conduit Clips
Cat. No.
Description
50382
50384
50385
50386
50388
1/2" EMT 1" pin
3/4" EMT 1-1/4"
3/4" EMT 1" pin TH
3/4" EMT 1-1/8" pin
1" EMT 1" pin TH
Cat. No.
Description
50376
50378
1-1/8" Pin w/domed right angle cc w/post nut
1-1/4" Pin w/domed right angle cc w/post nut
Rebar Basket Assemblies
Rebar basket clips are typically used in highway construction and paving
applications to hold the support baskets for the reinforcing bars in place while
the concrete is being poured. For #4 rebar.
8mm Diameter Head Drive Pins with EMT Conduit Clips
Cat. No.
Description
50276
50278
50280
27mm TH w/ 1/2" EMT
27mm TH w/ 3/4" EMT
27mm TH w/ 1" EMT
Head Dia.
Shank Dia.
Std. Box
Std. Ctn.
8mm
8mm
8mm
.145
.145
.145
100
100
25
1000
500
250
8mm Head Drive Pins with Rebar Basket Clip
Cat. No.
Description
50716
50718
62mm w/ basket clip
72mm w/ basket clip
Head Dia.
Shank Dia.
Std. Box
Std. Ctn.
8mm
8mm
.145
.145
100
100
500
500
For concrete forming applications the 2-1/2" (62mm) pin is designed for wood
members up to 1-1/2" in thickness. The pin has a break off groove 1" from the
point to allow the wood forming members to
be easily removed.
Ceiling Clips Without Pins
8mm Head Drive Pins with Rod Hanger Clip
Cat. No.
Description
50219
50221
32mm (1-1/4") pin w/ 1/4"-20 rod hanger
Shank Dia.
Std. Box
Std. Ctn.
.145
.145
100
100
1000
1000
Shank Dia.
Std. Box
Std. Ctn.
.157
100
1000
8mm Head spiral CSI Drive Pin with Rod Hanger Clip
50
Cat. No.
Description
50215
Ceiling clips
Cat. No.
Description
50400
Ceiling clip (no pin) 9/32"& 5/16" holes
Std. Box
Std. Ctn.
100
1000
P1000 • T1000
POW DER
T1000
Size Range
Size Range
1/2" to 3" pin lengths, .22 Caliber
Hammer actuated, powder actuated tool. Engineered for high reliability, low
maintenance and speed. This tool uses four levels of power; grey through yellow
loads (levels 1-4) and .300 , 8mm head fasteners with lengths of 1/2" through
3" and 1/4"-20 threaded studs.
Professional grade powder actuated tool engineered for high reliability, low
maintenance and speed. Its easy to use trigger mechanism makes fastening to
concrete, block and steel. The tool uses 22 caliber powder loads.
TECHNICAL DATA
tooL body
ACTUATED
P1000
TECHNICAL DATA
tooL body
Pin Length
Precision Moulded Rubber 1/2" to 3" Total Length
Pin Length
Precision Moulded Rubber 1/2" to 3" Total Length
Tool Length
Load Type
Tool Length
Load Type
13"
.22 Caliber
13"
.22 Caliber
tool weight
power level
tool weight
power level
3 lbs.
Gray (1), Brown (2), Green (3), Yellow (4)
3 lbs.
pin Type
Ballistic Point Drive Pin, .300 Head Drive Pin, 8mm Head Drive Pin,
1/4" -20 Threaded Stud
pin Type
1/4" -20 Threaded Stud
Typical Applications
Remodeling • Electrical • Maintenance • Telecommunications
Remodeling • Electrical • Maintenance • Telecommunications
T1000 Selection Guide
P1000 Selection Guide
Cat. No.
Description
52013
P1000 Tool
Std. Ctn.
Tool Operation: Powder actuated tools may be used only by properly trained and licensed operators as described in
ANSI Standard A 10.3. For complete tool operation details, completely review the tool manual and contact your local
Powers branch office or distributor for training.
1
Cat. No.
Description
52035
T1000 Tool
Std. Ctn.
1
51
POW DER
ACTUATED
P2201 • P35S
P2201
P35s
Size Range
Size Range
1/2" to 1-1/2" pin lengths, .25 Caliber
The P2201 is a low velocity, single shot, .22 caliber tool which can be used to
install .300 head drive pins, 8mm head drive pins and 1/4"-20 threaded studs,
up to 3” in total length. The P2201 is designed for maintenance or residential
contractors.
The P35s is specially designed for acoustical and drywall contractors. It is a low
velocity, semi-automatic, tool which can be used to install .300 head drive pins,
8mm head drive pins and 1/4"-20 threaded studs up to 1-1/2" in total length.
The P35s is designed for high speed and repetitive volume applications. The
standard version of the tool is supplied with a flat end piston and a full size
Baseplate/guide. A limited access Baseplate/guide assembly is also available.
TECHNICAL DATA
tooL body
Pin Length
Engineered Plastic
1/2" to 3"Total Length
Tool Length
Load Type
12-1/2"
.22 Caliber Crimped “A” Load
tool weight
power level
4.3 lbs.
TECHNICAL DATA
pin Type
tooL body
Pin Length
Precision Cast Aluminum
1/2" to 1-1/2" Total Length
Tool Length
Load Type
11-1/4"
.25 Caliber in a 10 Load Strip
tool weight
power level
4.25 lbs.
Green (3), Yellow (4), Red (5)
pin Type
TRADE
APPLICATION
Acoustical
Drywall
Electrical
Mechanical
Ceiling clip assemblies
Metal track, door frames
Boxers, conduit clip assemblies
Duct straps
Cat. No.
Description
52006
52007
52522
52510
52512
P2201 Tool
P2201 (Blister Pack)
Piston
Nose Piece
Piston Reset Pin
Std. Ctn.
1
1
1
1
1
TRADE
APPLICATION
Acoustical
Drywall
Electrical
Mechanical
Duct straps
P35s Selection Guide
Cat. No.
Description
52002
52023
52200
52204
52206
P35s Tool (Deluxe Kit)
P35s Tool (Blister Pack)
Piston Standard 21/SDF
Guide 21/F3-1
Baseplate 21/S1
Std. Ctn.
1
1
1
1
1
Pole tools for overhead attachments
Cat. No.
Description
50065
50066
6’ Di-Electric Pole Tool
Std. Ctn.
52
1
1
P3500 • PA3500
POW DER
P3500
PA3500
Size Range
Size Range
1/2" to 3" pin lengths, .27 caliber
1/2" to 3" pin lengths, .27 caliber
The P3500 is a low velocity, semi-automatic .27 caliber tool which can be
used to install .300 head drive pins, 8mm head drive pins and 1/4"-20 threaded
studs, up to 3" in total length. The P3500 is designed for high speed and
repetitive volume applications.
The PA3500 is a modified version of the P3500 that includes a power adjuster,
allowing the operator to effectively decrease the power level of the load being
used. A red load can be reduced down to the level of a green load.
TECHNICAL DATA
Power adjuster settings
1 - Minimum Power
3 - Medium Power
6 - Maximum Power
tooL body
Pin Length
TECHNICAL DATA
1/2" to 3" Total Length
tooL body
Pin Length
Tool Length
Load Type
13-5/8"
.27 Caliber / 10 Load Strip
Tool Length
Load Type
tool weight
power level
5 lbs.
Brown (2), Green (3), Yellow (4), Red (5)
pin Type
13-5/8"
.27 Caliber / 10 Load Strip
tool weight
power level
5 lbs.
pin Type
TRADE
APPLICATION
Acoustical
Drywall
Electrical
Mechanical
Forming
Residential
Duct straps
Concrete forms, basket clips, forming pins
Sill plates
TRADE
APPLICATION
Acoustical
Drywall
Electrical
Mechanical
Forming
Residential
Duct straps
Sill plates
Cat. No.
Description
PA3500 Selection Guide
Std. Ctn.
52000
P3500 Powder Tool (Deluxe Kit)
52001
P3500 Powder Tool (Blister Pack)
52102
Piston Flat End w/ Ring
52108
Guide 2/F-3
52110
Base Plate 2/S-13
52120
Shear Clip
52112
Piston Stop
52122
Steel Annular Ball
52106
Piston Ring
PISTON FOR INSTALLING 8MM HEAD DRIVE PINS
52100
Piston 2/DN-1 (for 8mm Head Drive Pins)
For applications in tight areas,
a limited access Base plate/guide is available.
52114
Guide 2/F-4 Limited Access
52116
Baseplate 2/F-14-1 Limited Access
1
1
1
1
1
1
1
1
1
1
1
1
Cat. No.
Description
50065
50066
ACTUATED
Std. Ctn.
1
1
Cat. No.
Description
Std. Ctn.
52019
PA3500 Powder Tool (Deluxe Kit)
52025
PA3500 Powder Tool (Blister Pack)
52103
PA Piston Flat End with Ring
52108
Guide 2/F-3
52110
Base Plate 2/S-13
52112
Piston Stop
52120
Shear Clip
52122
Steel Annular Ball
For applications in tight areas,
a limited access Base plate/guide is available.
52114
Guide 2/F-4 Limited Access
52116
Baseplate 2/F-14-1 Limited Access
1
1
1
1
1
1
1
1
1
1
Cat. No.
Description
50065
50066
Std. Ctn.
1
1
53
POW DER
ACTUATED
P3600 • SNIPER POLE TOOL
P3600
Size Range
1/2" to 3" 10mm head pins, 3/8" threaded studs, 3/8" headed drive pins
.22 caliber strip
Sniper™ Pole Tool
The P3600 is a powerful, heavy-duty low velocity, semi-automatic .27 caliber
tool which can be used to install 10mm head drive pins, 3/8" threaded studs,
and 3/8" headed drive pins. The P3600 is designed for applications where more
power is needed, such as attaching 2x4s to hard aggregate or steel. The tool
utilizes a red or purple .27 caliber strip.
1/2" to 1-1/2" pin lengths, .27 caliber strip
tooL body
Pin Length
Ideally suited to installing overhead ceiling clips with a 1-1/2"" pin. Features
Safety Sequence Strip Loading, allowing load advancements only after the pin
has been installed in the nose piece, and the handle must be clicked to advance
the next load.
TECHNICAL DATA
Tool Length
Load Type
tooL body
13-5/8"
1-1/2" Total Length
tool weight
power level
Tool Length
Load Type
5 lbs.
Red (5), Purple (6)
TECHNICAL DATA
Pin Length
17"
pin Type
tool weight
power level
10mm Head Pins, 3/8" Threaded Studs, 3/8" Headed Drive Pins
8 lbs.
.300 Head Drive Pin, 8mm Head Drive Pin, Ballistic Point Drive Pin
2x4s to concrete or steel
Tele-communications
Sill plates
pin Type
Hanging sprinkler pipe
Heavy-duty applications for steel and concrete
Cat. No.
Description
52010
52579
52112
52578
P3600 Tool (Deluxe Kit)
Guide for the P3600
Piston Stop for the P3600
Piston for the P3600
Std. Ctn.
1
1
1
1
Cat. No.
Description
50065
50066
Std. Ctn.
54
Size Range
1
1
TRADE
APPLICATION
Acoustical
Drywall
Electrical
Mechanical
Forming
Residential
Duct straps
Sill plates
sniper Selection Guide
Cat. No.
Description
52051
52053
52061
Sniper Tool (Bump Tool)
6' Pole
8' Pole
Std. Ctn.
1
1
1
POWDER LOADS
Specific load types are designed for each unique powder actuated tool. Offered
as single units for single shot tools and collated in groups of 10 in plastic strips.
.22 Caliber “A” Low Velocity Loads
For Powers T1000, P1000, P2201, P7200, P2200, Ramset® 721 and M70, Hilti® DXE37 and DXE72
Cat .No.
Description
Std. Box
Std. Ctn.
Master Ctn.
Gray, .22A
Brown, .22A
Green, .22A
Yellow, .22A
100
100
100
100
5000
5000
5000
5000
240,000
240,000
240,000
for LADD Ceiling Master Tool (L1600)
Cat. No.
Description
Std. Box
Std. Ctn.
Master Ctn.
100
5000
-
Std. Box
Std. Ctn.
Master Ctn.
100
100
2500
2500
100,000
100,000
.22 Caliber Loads
50520
Purple - Ladd
ACTUATED
50500
50502
50504
50506
POW DER
Powder Loads
.27 Caliber long loads
for POWERS P3801, Ramset® MD380 and Hilti® DX600N
Cat. No.
Description
50612
50614
Red, .27 long
Purple, .27 long
.25 Caliber 10 load strips
for Powers P35S and Hilti® DX35
Cat. No.
Description
50570
50574
50578
Green, .25 strip
Yellow, .25 strip
Red, .25 strip
Std. Box
Std. Ctn.
Master Ctn.
100
100
100
1000
1000
1000
20,000
20,000
20,000
MASTER PACK
Cat. No.
Description
50572
50576
50580
Green, .25 strip
Yellow, .25 strip
Red, .25 strip
Std. Box
Std. Ctn.
Master Ctn.
1000
1000
1000
20000
20000
20000
-
Safety Strip®
The safety strip is molded in a special length to provide a visual indication that
the tool is loaded.
.27 Caliber safety strip loads
for Powers P3500, PA3500, PA351, P3600, Ramset® SA270, Viper, Hilti® DX350, DX36M, DX451 AND DX460
Cat. No.
Description
Std. Box
Std. Ctn.
50620
50622
50626
50630
Brown, .27 safety strip
Green, .27 safety strip
Yellow, .27 safety strip
Red, .27 Safety Strip
MASTER PACK
Cat. No.
Description
50624
50628
50632
Green, .27 safety strip
Yellow, .27 safety strip
Red, .27 safety strip
Ramset® is a registered trademark of Illinois Tool Works, Inc.
100
100
100
100
1000
1000
1000
1000
Std. Box
Master Ctn.
1000
1000
1000
10,000
10,000
10,000
Hilti® is a registered trademark of Hilti, Inc.
.27 Caliber 10 load strips
for Powers P3600, Hilti® DX460
Cat. No.
Description
50606
Purple, .27 strip
Std. Box
Std. Ctn.
Master Ctn.
100
1000
20,000
55
58
0.145 "
3/4" : 1"
•
•
•
Steel Pins
58
0.120 "
0.500" : 0.680" : 0.730"
Step Shank Pins
58
0.145" : 0.102"
1-1/4" : 1-1/2"
•
Stick-E Pins (Step Shank)
58
0.120" : 0.088 "
0.780"
•
Plywood to Steel Pins
(Special Knurl Shank
with Rolled Point)
58
0.102"
1-3/8""
1/2" Steel Pins
(Step Shank w Rolled Point)
58
0.102 "
1/2"
Standard Pins
(Smooth Shank w Rolled Point)
58
0.145"
3/4" : 1
•
•
Wood to Concrete Taper Pins
58
0.137"
2-9/16"
•
•
(Spiral Knurl Shank w Rolled Point)
58
0.120"
0.500" : 0.680" : 0.730"
Bullseye Pins
58
0.120" : 0.102"
0.500" : 0.680" : 0.730"
•
•
ACQ Coated Step Shank Pins
58
0.145"
1-1/2" to 2"
•
•
1/2" Steel Pins
59
0.120" : 0.102 "
1/2"
Standard Pins
(Smooth Shank w Rolled Point)
59
0.102 "
3/4" : 1" : 1-1/4" : 1-1/2"
(Spiral Knurl Shank w Rolled Point)
59
0.102 "
1-3/8"
Bullseye Pins
59
0.120" : 0.102 "
1-1/16" : 3/4" : 1"
59
0.102" : 0.088 "
0.780" : 1"
• Suitable
May be Suitable
Stick-E Accessories
Straight Pins (Smooth Shank)
Wood to Steel
•
A36/A572 Steel
•
Plywood to Light Gauge Steel
On Metal Deck
•
Brick Masonry
3/4" : 1" : 1-1/4" : 1-1/2"
Concrete
0.102"
Grouted Concrete Masonry
Length
58
Wood Sill Plate to Concrete
Diameter
Straight Pins (Smooth Shank)
Stick-E Pins
(Step Shank)
56
Base Material
Page
Trak-It C3 Pins
Trak-It C4 Pins
Trak-It C5 Pins
GAS
Dimensions
High Strength / Concrete Precast
Concrete
FASTENI NG
SELECTION GUIDE
•
Code
Recognition
ICC-ES ESR-3275
LARR-25920
•
ICC-ES ESR-3275
LARR-25920
•
ICC-ES ESR-3275
LARR-25920
ICC-ES ESR-3275
LARR-25920
•
•
•
•
•
•
Denz-Glass
Washer
•
•
•
ICC-ES ESR-3275
LARR-25856
ICC-ES ESR-3275
LARR-25856
•
•
ICC-ES ESR-3275
LARR-25856
•
•
•
ICC-ES ESR-2036
LARR-25523
•
•
•
•
•
ICC-ES ESR-2036
LARR-25523
•
•
Denz-Glass
Washer
•
•
•
•
•
•
•
TRAK-IT C4
GAS
FASTENI NG
Long Shot
Pole Tool
Reaching
New heights.
No more lifts. No more ladders.
Shoot straight from the floor to
the ceiling with the Powers
Trak-It ® C5 Pole Tool.
Allows 8’ of reach, with an
additional 3’ section available
for higher jobs.
Well-balanced and rigidly
constructed, the pole tool makes
shooting overhead a breeze.
Call 800-524-3244 for a free
hands on C5 pole tool demo.
55054
Bridal Ring
Uniquely
Designed
Tool Cradle
Locking strap keeps
C5 tool secure.
Easy
Disassembly
for convenient
storage.
55092
55302
Right
Fuel Cell
Angle Clip
55310
55336
55342
Pins
Versatile Tool
Trigger Design
Rubber over molded
handle and grip
rotates 360 degrees for
accessing tight areas.
57
GAS
FASTENI NG
TRAK-IT C5 • TRAK-IT C4 PINS
Trak-It® C5
New!
Gas Fastening System
Base Material
Concrete, Lightweight Concrete, Hollow and Grouted CMU, Masonry & Steel
55325
The all new fuel injected Trak-It C5
cordless concrete pin nailer is the
lightest and smallest tool in its class,
resulting in less operator fatigue
and a better overall ergonomic feel.
C5 has the greatest power output at
105 Joules, which allows for shooting into even the hardest concrete,
able to shoot pins up to 1-1/2" in
length, and is the only tool in its
class that shoots .102, .108, .120
and .145 diameter pins. No other
tool can make this claim!
Cat. No.
Shank Dia.
Length
55326
55325
0.120"
1/2"
-
Zinc
-
800
4,000
55326
0.120"
1/2"
0.102"
Zinc
K
800
4,000
55328
0.120"
0.680"
0.102"
Zinc
K
800
4,000
55330
0.120"
0.730"
0.102"
Zinc
K
800
4,000
55342
0.102"
0.780"
0.088"
Zinc
K
800
4,000
Length
Step Dia.
plate knurl/ spiral
Std. Box
c5
Std. Ctn.
1-3/8"
0.102"
specialty tapered short pins
Step Dia.
plate
knurl/ spiral
Std. Box
specialty spiral knurl pin
Cat. No.
Shank Dia.
55340
0.108"
Zinc
KS
800
c5
Std. Ctn.
4,000
Trak-it C5 Tool
Cat. No.
Description
55142
55144
55148
C-5 Gas Tool Long Deep Track
C-5 Gas Tool Short Track
C-5 Gas Tool Long Track
pin length
Std. Box
Std. Ctn.
1
1
1
–
–
–
1-1/4"
1-1/2"
1-1/2"
Tool accessories
Cat. No.
Description
56347
56348
56342
55583
56346
56344
C5 Pole Tool Accessory Kit (C5 not included)
C5 Pole Tool 3' Extension
Accessory Deep Track
1-1/4"
Battery
Accessory Short Track
1-1/2"
Accessory Long Track
1-1/2"
Std. Box
Std. Ctn.
1
1
1
1
1
1
1
1
–
–
–
Note: Short track tool for 1.5" pins which does not shoot deep track can be ordered under part number 55144
Note: Long track tool for 1.5" pins which does not shoot deep track can be ordered under part number 55148
Trak-it c3 & c4 fuel cells
Cat. No.
Description
55010
55115
n Trak-It C3 Fuel Cell
n Trak-It C4 Fuel Cell
Std. Box
Std. Ctn.
20
12
80
72
Works in temperatures down to 10˚F.
TRAK-IT Fuel Cells
Cat. No.
Description
55015
n Red Nailing Gas Fuel Cell
C4 Trak-It® Pins
Code listed
ICC-ES ESR-3275
Std. Box
Std. Ctn.
12
12
city of los angeles
fuel cells
Cat. No.
Description
55302
55301
Fuel Cell
100 per box
Std. Box
Std. Ctn.
20
100
80
–
55171
trak-it c4
C4 pins and
& washers
washers
Code listed
city of los angeles
ICC-ES ESR-3275
standard 0.102 straight pins
c5
Std. Ctn.
55111
Shank Dia.
Std. Box
c4
Std. Ctn.
1/2" Pin, Knurled
3/4" Pin
0.102"
0.102"
800
800
4000
4000
Cat. No.
Description
55161
55111
Cat. No.
Shank Dia.
Length
Step Dia.
0.102"
3/4"
55130
3/4" Pin
4000
-
Zinc
-
800
4,000
0.145"
800
55310
1"
1" Pin
4000
-
Zinc
-
800
4,000
0.102"
800
55312
0.102"
55113
1-1/4"
1" Pin
4000
-
Zinc
-
800
4,000
0.145"
800
55314
0.102"
55132
1-1/2"
1-1/4" Step Shank Pin
4000
-
Zinc
-
800
4,000
0.145"
800
55316
0.102"
55134
55173
55169
55118
55136
1-1/4" Wood/Steel Knurled
1-1/4" Step Shank Knurled ACQ
1-1/2" C4 Pin
0.145"
0.145"
0.102"
0.145"
800
800
800
800
4000
4000
4000
4000
Std. Box
c5
Std. Ctn.
55174
55171
55139
55128
55140
55145
2" Wood/Steel Knurled
2" Step Shank Knurled ACQ
2-1/2" Pin
2-9/16" Pin (Mechanically Galvanized)
0.145"
0.145"
0.145"
0.102"
0.145"
0.137"
800
800
800
800
800
800
4000
4000
4000
4000
4000
4000
plate knurl/ spiral
Std. Box
standard 0.145 straight pins
Cat. No.
Shank Dia.
Length
Step Dia.
55318
0.145"
3/4"
-
Zinc
plate knurl/ spiral
-
800
4,000
55320
0.145"
1"
-
Zinc
-
800
4,000
Each box of pins come packaged with one fuel cell.
Concrete and steel pins structural
58
Cat. No.
Shank Dia.
55336
55338
c5
Std. Ctn.
Length
Step Dia.
plate
knurl/ spiral
Std. Box
0.145"
1"
0.120"
Zinc
K
800
4,000
0.145"
1-1/4"
0.120"
Zinc
K
800
4,000
55322
0.145"
1-1/4"
0.102"
Zinc
-
800
4,000
55324
0.145"
1-1/2"
0.102"
Zinc
-
800
4,000
TRAK-IT C3 PINS • STICK-E
stick-e Conduit clip (one hole strap)
Cat. No.
Description
55020
1/2" Steel Pin
Shank Dia.
Std. Box
c3
Std. Ctn.
0.120/0.102
1000
5000
Cat. No.
Description
55022B
55024
55026
55028
3/4" Black
1" Zinc
1-1/4" Zinc
1-1/2" Zinc
Shank Dia.
Std. Box
c3
Std. Ctn.
0.102
0.102
0.102
0.102
1000
1000
1000
1000
5000
5000
5000
5000
Std. Box
Std. Ctn.
Conduit Clip 1/2"
100
1000
55061
Conduit Clip 3/4"
100
1000
55063
Conduit Clip 1"
100
1000
Cat. No.
Description
55054
3/8" BX Clips
Cat. No.
Description
55094
Bridal Ring 1-1/4"
55095
stick-e bx clip
Designed for use in A36 and A572 steel beams, purlins, and bar joist. Each box of pins come packaged with
one fuel cell.
standard pins (smooth shank with rolled point)
Description
55059
Std. Box
Std. Ctn.
100
1000
Std. Box
Std. Ctn.
100
1000
Bridal Ring 1-1/2"
100
1000
55096
Bridal Ring 2"
100
1000
Cat. No.
Description
Std. Box
Std. Ctn.
55062
Strap Washer 1/2" Diameter
100
1000
Cat. No.
Description
Std. Box
Std. Ctn.
55050
Rod Hanger 1/4”
100
1000
55052
Rod Hanger 3/8”
100
1000
Std. Box
Std. Ctn.
100
1000
Std. Box
Std. Ctn.
100
1000
Std. Box
Std. Ctn.
100
1000
Std. Box
Std. Ctn.
100
1000
Std. Box
Std. Ctn.
100
1000
Std. Box
Std. Ctn.
100
1000
Std. Box
Std. Ctn.
800
1000
stick-e bridal ring
Designed for use in concrete and masonry. All pins are zinc plated for a minimum level of corrosion resistance.
Each box of pins come packaged with one fuel cell.
FASTENI NG
1/2" steel pin (step shank with rolled point)
Cat. No.
GAS
C3 Trak-It® Pins
stick-e strap washer
plywood to steel pins (spiral shank with rolled point)
Cat. No.
Description
55036
1-3/8” Zinc
Shank Dia.
Std. Box
c3
Std. Ctn.
0.102"
1000
5000
Designed for use to attach plywood to light gage steel framing. Each box of pins come packaged with
one fuel cell.
bullseye pins (step shank with rolled point)
Shank Dia.
Std. Box
c3
Std. Ctn.
730 Step Shank Pin
0.102"
1000
5000
780 Step Shank Pin
0.102"
1000
5000
0.102/0.088"
1000
5000
Cat. No.
Description
55087
55080
55081
1" Step Shank Pin
stick-e rod hanger
stick-e rebar basket clip
Cat. No.
Description
55070
#3 & #4 Bar
Designed for use in hard aggregate and precast concrete. Each box of pins come packaged with one fuel cell.
stick-e right angle clip
Cat. No.
Description
55092
Right Angle Clip
(Wire Hole 0.278")
Trak-it Accessories
Cat. No.
Description
55618
55619
55583
Replacement Trak-It ChargerBase
Replacement Trak-It Charger Adapter Cord (110V)
Extra Battery for Trak-It Tool
Std. Box
Std. Ctn.
1
1
1
1
1
1
Trak-It® STICK-E
stick-e mini conduit clip
Cat. No.
Description
Std. Box
Std. Ctn.
55064
Mini Conduit Clip 1/2"
100
1000
55066
Mini Conduit Clip 3/4"
100
1000
55068
Mini Conduit Clip 1"
100
1000
stick-e mini cable tie donut
Description
55076
Cable Tie Donut
Cat. No.
Description
55042
Insulation Washer 1-7/16"
stick-e lathing washer
Designed for use in concrete and masonry. Pins are zinc plated or coated with
black oxide for a minimum level of corrosion resistance. Plastic collation breaks
completely free of pin during installation. Each box of pins come packaged with
one fuel cell.
Cat. No.
stick-e insulation washer
Std. Box
Std. Ctn.
100
1000
Cat. No.
Description
55040
Lathing Washer 1"
with Holes
stick-e stainless steel sealing washer
Cat. No.
Description
55043
SS Sealing Washer 3/4"
stick-e denz-tight™ pin washer
Cat. No.
Description
55157
Denz-Tight Pin Washer
stick-e square washer
Cat. No.
Description
55149
1" Square Washer
59
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Engineereed Plastic
•
Galvalume
Perma-Seal Coated
Carbon Steel
•
Stainless Steel
13"
Gypsum
Cement Wood Fiber
Insulating Cover
Lightweight Concrete Deck
Concrete Deck
Wood Deck
12"
54
11"
Stress Plates
10"
•
9"
54
8"
Twin Fast Screws
•
7"
•
•
6"
54
•
5"
Deck Screws
•
4"
53
3"
Powerlite
Coating/Material
2"
53
May be Suitable
Insulation Thickness
•
Perma-Seal Roofing Spike
• Suitable
60
Steel Deck
Page
Base Material
1"
ROOF I NG
SELECTION GUIDE
•
•
•
•
•
spike • powerlite
ROOF I NG
Spike® (Perma-Seal®)
Powerlite™
Roofing Anchor
Roofing Anchor
Base Material
Base Material
Concrete
Structural Cement Wood Fiber, Gypsum, or Lightweight Concrete
Size Range
Size Range
3/16" x 1" to 1/4" x 14"
2" to 14" Lengths
Anchor Material
Anchor Material
Perma-Seal Coated Carbon Steel
Reinforced Engineered Nylon
For roofing applications, the Spike is a one-piece, vibration resistant anchor
available in 1/4” diameter for use in fastening insulation, single-ply membrane,
wood, and metal to structural concrete roof decks. This version of the SPIKE has
a Perma-Seal coating a proprietary fluoropolymer which meets the corrosion
resistance requirements of FMRC Standard 4470. It is designed for use in
conjunction with Powers insulation or membrane stress plates.
Perma-seal spike
Cat. No.
Anchor Size
3811
3723
3725
3727
3729
3731
3733
3735
3737
3739
3741
3743
3745
3747
3749
3753
3757
3765
3769
3773
3777
1/4" x 1-1/4
1/4" x 1-1/2"
1/4" x 2"
1/4" x 2-1/2"
1/4" x 3"
1/4" x 3-1/2"
1/4" x 4"
1/4" x 4-1/2"
1/4" x 5"
1/4" x 5-1/2"
1/4" x 6"
1/4" x 6-1/2"
1/4" x 7"
1/4" x 7-1/2"
1/4" x 8"
1/4" x 9"
1/4" x 10"
1/4" x 11"
1/4" x 12"
1/4" x 13"
1/4" x 14"
Drill Dia.
Min. Embed.
Std. Box
Std. Ctn.
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
7/8"
7/8"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
500
500
500
500
500
500
500
500
500
500
250
250
250
250
250
250
250
100
100
100
100
500
500
500
500
500
500
500
500
500
500
250
250
250
250
250
250
250
100
100
100
100
The Powerlite is a fastener used to mechanically attach rigid insulation board
and single-ply membrane to structural cement wood fiber, gypsum, and lightweight insulating concrete roof decks. The fastener is used in conjunction with
insulation and membrane stress plates. The plates are manufactured with four
barbs on the underside that grip the insulation board or single-ply membrane
preventing rotation.
powerlite roofing anchor
Cat. No.
Length
4670
4671
4669
4672
4673
4674
4675
4676
4677
4678
4679
4680
4681
4683
4684
4685
4686
4687
4688
4689
4691
4692
2"
2-1/2"
2-3/4"
3"
3-1/2"
4"
4-1/2"
5"
5-1/2"
6"
6-1/2"
7"
7-1/2"
8"
8-1/2"
9"
9-1/2"
10"
11"
12"
13"
14"
Min. Embed.
Std. Ctn.
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2”
1-1/2”
1-1/2”
1-1/2”
1-1/2”
1-1/2”
1-1/2”
1-1/2”
1-1/2”
1-1/2”
1-1/2"
1-1/2"
500
500
500
500
500
500
500
500
500
500
500
250
250
250
250
250
250
250
250
250
250
250
Powerlite plates (galvalume)
Cat. No.
Length
3876
3896
2" Powerlite Membrane Plate
3" Powerlite Insulation Plate
spike installation tools for roofing applications
Cat. No.
Description
3790
3791
SPIKE Driver 1000
SPIKE Driver 2000
Guide I.D.
Std. Box
1/2"
1/2"
1
1
Std. Ctn.
500
500
Powerlite installation accessories
Cat. No.
Description
4695
4696
Powerlite Bit Tip
Powerlite Bit Holder
Std. Box
1
1
-
61
ROOF I NG
deck screws • stress plates
Stress Plates
Base Material
Insulation, Single-Ply Roofing Materials
Deck Screws
Size Range
Roofing Anchor
2" and 3"Round
Base Material
Anchor Material
Stainless Steel or Galvalume Disk
Steel, Wood or Concrete Roof Decks
Size Range
No. 12 x 1-5/8" to No. 12 x 8"
Anchor Material
Perma-Seal Coated Carbon Steel
Deck Screws are designed for attaching rigid insulation board, single ply membrane, and wood blocking to steel and wood decks. Available sizes include No.
12 diameters in carbon steel with either hex washer or Phillips-style heads. The
Deck Screws are used in conjunction with insulation or membrane plates and
can also be used with batten bar. For corrosion protection the screws are coated
with Perma-Seal coating, a proprietary fluoropolymer, which meets the requirements of Factory Mutual Standard 4470.
perma-seal coated No.12 ph deck screw
Cat. No.
Size
2613
2618
2624
2530
2632
2636
2640
2648
2656
2664
No. 12 x 1-5/8"
No. 12 x 2-1/4"
No. 12 x 2-7/8"
No. 12 x 3-1/4
No. 12 x 3-3/4"
No. 12 x 4-1/2"
No. 12 x 5"
No. 12 x 6"
No. 12 x 7"
No. 12 x 8"
Thread Length
Std. Box
Std. Ctn.
1-1/2"
2"
2-5/8"
3"
3"
3"
3"
4"
4"
4"
1000
1000
1000
1000
1000
1000
1000
1000
500
500
1000
1000
1000
1000
1000
1000
1000
1000
500
500
Stress plates are designed for use with Deck Screws and Spike anchors. Stress
plates can be grouped into two categories; insulation plates and membrane
plates. Insulation plates, as the term implies, are used when mechanically attaching rigid foam insulation to roof decks. They are manufactured in a 3" diameter
for use with No. 12, No. 14, and No. 15 Deck Screws™, 3/16" and 1/4" Spike
anchors, and 1/4" Speed Lock Toggles. Two carbon steel plates, a Type 304
stainless steel plate, disc are available. A recessed plate is available for use
with the No. 12 hex washer head screws. For corrosion resistance, a Galvalume
coating is applied to the carbon steel plates. Membrane plates, sometimes called
lap plates, are used when mechanically attaching single ply material in the area
of the lap or seam. They are manufactured in a 2" diameter for use with No. 12
Deck Screws and 1/4" Spike anchors.
insullation plates - for ph screws
Cat. No.
Size
3880
3881*
3" round
3" round
Plate Thickness
Material
Std. Ctn.
.019"
.019"
Galvalume
Stainless Steel
500
500
driver bits for deck screws
Cat. No.
Size
3585
3590
No. 3 Phillips Power Bit (2")
1/4” Hex Bit (1-7/8")
Std. Box
1
1
membrane plates
Cat. No.
Size
3878
2" round barbed
Plate Thickness
Material
Std. Ctn.
034"
Galvalume
1000
Stainless Steel Sealing and Plastic Washers
Stainless Steel Sealing and Plastic Washers are typically used with 1/4" diameter
anchors for roof flashing, termination bar and dissimilar metal applications.
Twin Fast Screws
Roofing Anchor
twin fast screws
Cat. No.
Size
2210*
2225*
2229*
8-18 x 1/2" Pan Head
10-16 x 3/4" Hex Head
10-16 x 1"Hex Head
Std. Box
sealing washer type 304 stainless steel with EPDM seal
Cat. No .
Size
2896
1/4" (ID) x 1-1/8" (OD)
Std. Box
Std. Ctn.
100
1000
Std. Box
Std. Ctn.
1000
-
plastic washer
62
Cat. No.
Size
3994
1/4" (ID) x 1-1/2” (OD) Poly
Selection Guide
DRI L L I NG
•
•
•
•
•
•
Quatro Head SDS
57
•
•
•
•
•
•
•
•
•
•
4-X Cutter Spline Shank
58
Single Tip Spline Shank
58
HD Straight Shank
58
•
IG Straight Shank
58
•
"A" Taper shank
59
Rotary Carbide Bits
59
Rebar Cutter
59
Heavy Duty Chisels
59
One & Two Piece Core Bits
60
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
4-X Cutter SDS-Max Shank 57
•
5"
57
•
4"
Industrial Grade
•
3-1/2"
•
3"
•
2-1/2"
•
2"
•
1-3/4"
•
1-5/8"
•
1-1/2"
•
1-3/8"
•
1-1/4"
•
1-1/8"
56
1"
S-4 Plus SDS
7/8"
9/16"
•
27/32"
1/2"
•
3/4"
7/16"
•
11/16"
3/8"
•
5/8"
5/16"
56
9/32"
•
•
Fat-Head
1/4"
•
7/32"
3/16"
5/32"
1/8"
Page
Diameter
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
• Suitable
May be Suitable
63
DRI L L I NG
fathead • sds-plus / s-4 plus sds
SDS-Plus / S-4 Plus SDS
Carbide Drill Bits
FatHead Bits
™
use in
Rotary hammer with SDS chuck or SDS adapter
Solid Carbide Head Carbide Drill Bits
Size Range
5/32" x 6" to 1" x 18"
use in
Size Range
3/16" x 4-1/4" to 9/16" x 18"
Powers FatHead combines an intelligent, innovative geometry with uncompromising
quality in its detail. This is reflected in prolonged durability, precision drill holes and
exceptional low vibration - even when the going gets tough. A premium tool for
anyone who has to drill into reinforced concrete or natural stone.
fathead carbide drill bits
Cat. No.
Size
0701
0703
0705
0707
0709
0711
0713
0715
0717
0719
0721
0723
0727
0729
0731
0733
0735
0739
0741
0743
0745
0747
3/16" x 4-1/2"
3/16" x 6-1/2"
3/16" x 8-1/2"
3/16" x 10-1/2"
3/16" x 12"
1/4" x 4-1/2"
1/4" x 6-1/2"
1/4" x 8-12"
1/4" x 10-1/4"
1/4" x 12"
5/16" x 6-1/2"
5/16" x 12"
3/8" x 6-1/2"
3/8" x 12"
3/8" x 18"
7/16" x 6-1/4"
7/16" x 12-1/4"
1/2" x 6-1/2"
1/2" x 12"
1/2" x 18"
9/16" x 6-1/2"
9/16" x 12-1/4"
5 Piece Drill Set Kit includes 3/16", 1/4", 5/16",
3/8" and 1/2" diameter bits (all 6" overall)
0751
Usable Length
2"
4"
6"
8"
10"
2"
4"
6"
8"
10"
4"
10"
4"
10"
16"
4"
10"
4"
10"
16"
4"
10"
Std. Tube
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
S-4 Plus SDS Carbide Drill Bits are designed for use in a rotary hammer
equipped with an SDS (slotted drive shaft) type chuck. The bits are manufactured
to conform with ANSI Standard B212.15 and can be used to drill in concrete,
block, brick, and soft stone.
SDS-plus / S-4 plus sds carbide drill bits
Cat. No.
Size
0302
0304
0306
0308
0310
0312
0314
0316
0317
0318
0319
0320
0321
0322
0323
0324
0325
0327
0329
0331
0333
0334
0336
0338
0339
0341
0343
0346
0348
0349
0351
0352
0354
0355
0359
0361
0362
0364
0365
0368
0370
0371
0373
0375
0376
0377
0379
0380
0381
0382
0394†
0396†
5/32" x 6-1/2"
3/16" x 4-1/2"
3/16" x 6-1/2"
3/16" x 8-1/2"
3/16" x 10"
3/16" x 12"
3/16" x 14"
7/32" x 8-1/4"
7/32" x 11"
7/32" x 14"
7/32" x 16"
1/4" x 4-1/2"
1/4" x 6-1/2"
1/4" x 8-1/2"
1/4" x 11"
1/4" x 14"
1/4" x 16"
1/4" x 20"
5/16" x 6-1/4"
5/16" x 12"
3/8" x 6-1/2"
3/8" x 10-1/4"
3/8" x 12-1/4"
3/8" x 18"
3/8" x 24"
7/16" x 6-1/4"
7/16" x 12-1/4"
1/2" x 6-1/2"
1/2" x 10-1/4"
1/2" x 12-1/4"
1/2" x 18"
1/2" x 24"
9/16" x 6-1/4"
9/16" x 10-1/4"
5/8" x 7-3/4"
5/8" x 12"
5/8" x 18"
11/16" x 8"
11/16" x 12"
3/4" x 8"
3/4" x 12"
3/4" x 18"
27/32" x 8"
7/8" x 8"
7/8" x 12"
7/8" x 18"
1" x 8"
1" x 10"
1" x 12"
1" x 18"
Spline to SDS Adapter
SDS Max Adapter
Usable Length
Std. Pouch
4-1/2"
2-1/2"
4-1/2"
6-1/2"
8"
10"
12"
6"
8"
12"
14"
2"
4"
6-1/2"
9"
12"
14"
18"
4-1/4"
10"
4-1/4"
8-1/4"
10-1/4"
16"
22"
4-1/4"
10-1/4"
4-1/4"
8-1/4"
10-1/4"
16"
22"
4-1/4"8"
6"
10"
16"
6"
10"
6"
10"
16"
6"
6"
10"
16"
6"
8"
10"
16"
-
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
† Use of SDS-Plus drill bit in larger rotary hammers with an adapter will reduce bit life.
64
industrial grade • sds-max
Cat. No.
Size
0662
0664
0666
0668
0670
0675
0676
0677
0680
0681
0682
0683
0689
0693
0696
0697
5/32" x 6-1/2"
3/16" x 4-1/2"
3/16" x 6-1/2"
3/16" x 8-1/2"
3/16" x 10"
7/32" x 6-1/4"
7/32" x 8-1/4"
7/32" x 11"
1/4" x 4-1/2"
1/4" x 6-1/2"
1/4" x 8-1/2"
1/4" x 11"
5/16" x 6-1/4"
3/8" x 6-1/2"
1/2" x 6-1/2"
5/8" x 7-3/4"
Usable Length
Bits Per Pack
4-1/4"
2-1/4"
4-1/4"
6-1/4"
8"
4"
6"
8"
2-1/4"
4-1/4"
6-1/4"
9"
4-1/4"
4-1/4"
4-1/4"
6-1/4"
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
Cat. No.
Description
0813
0815
0817
0819
0821
0823
0825
0827
0829
0831
7/32" x 8-1/4"
7/32" x 10"
1/4" x 4-1/4"
1/4" x 6-1/4"
1/4" x 8-1/4"
1/4" x 11"
5/16" x 6-1/4"
3/8" x 6-1/4"
1/2" x 6-1/4"
5/8" x 8"
USABLE LENGTH
Std. box
Std. Ctn.
6"
7-1/2"
2"
4"
6"
8-1/2"
4"
4"
3-1/2"
5"
25
25
25
25
25
25
25
25
15
15
450
300
450
500
450
300
500
300
180
120
DRI L L I NG
sds-plus / s-4 plus sds carbide drill bit bulk packs
* SDS® is a registered trademark of Robert Bosch Co.
SDS-Max®
use in
Dropin
SDS-plus accu Stop bit for dropin*
Cat. No.
Size
00391
00397
00410
00418
00419
SDS-Plus 1" Concrete Accu-Bit
Usable Length
Bits Per Pack
for 1/4" Dropin
for 3/8"Dropin
for 1/2" Dropin
for 5/8" Dropin
for 3/4" Dropin
1
1
1
1
1
For Smart DI+ Stop Bits see page 16.
Mini Dropin
SDS-plus accu stop bit for mini dropin
Cat. No.
Size
00392
00398
00411
Usable Length
Bits Per Pack
1
1
1
Quatro Head SDS-Plus Carbide Drill Bits are designed to reduce vibration and noise.
These bits produce rounder and more accurately located anchor holes.
quatro head sds-plus carbide drill bits
Cat. No.
Size
7094
7095
1-1/8" x 18"
1-1/4" x 18"
Usable Length
Std. Pouch
16"
16"
1
1
Rotary hammer with SDS-Max chuck
Size Range
1/2" x 13" to 1-1/2" x 23"
SDS-Max Carbide Drill Bits are designed for use in a rotary hammer equipped
with a SDS-Max type chuck. The bits are manufactured to conform with ANSI
Standard B212.15 and can be used to drill in concrete, block, brick, and soft stone.
4-X cutter head sds-max drill bits
Cat. No.
Size
8801†
8802†
8805†
8806†
8809
8810
8812
8815
8817
8818
8820
8829
8830
8833
8834
8836
8843
8844
8846
8847
8848
8853
8859
1/2" x 13-1/2"
1/2" x 21-1/2"
9/16" x 13-1/2"
9/16" x 21-1/2"
5/8" x 13-1/2"
5/8" x 21-1/2"
5/8" x 36"
11/16" x 21-1/2"
3/4" x 13-1/2"
3/4" x 21-1/2"
3/4" x 36"
7/8" x 13-1/2"
7/8" x 21-1/2"
1" x 13-1/2"
1" x 21-1/2"
1" x 36"
1-1/8" x 17"
1-1/8" x 22-1/2"
1-1/4" x 15"
1-1/4" x 22-1/2"
1-1/4" x 36"
1-3/8" x 22-1/2"
1-1/2" x 22-1/2"
Usable Length
Std. Tube
8"
16"
8"
16-1/2"
8"
16"
31"
16"
8"
16"
31"
8"
16"
8"
16"
31"
10"
18"
10"
18"
31"
18"
18"
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
SDS-Max is a registered trademark of Robert Bosch Co.
†
1/2" and 9/16" sizes have a standard single cutter tip and standard helical fluting.
Industrial Grade Bits (Value Paks)
Carbide Drill Bits fits SDS®
use in
Size Range
5/32" x 6" to 5/8" x 8"
These carbide bits are designed to be used in rotary hammer equipment with a
slotted drive shank. Available in bulk pack quantities only with the large volume
user in mind. These bits meet are manufactured to conform with ANSI standard
B212.15 and can be used in concrete, block, brick and soft stone.
industrial grade value pak bits
Cat. No.
Description
0801
0803
0805
0807
0809
0811
5/32" x 6-1/4"
3/16" x 4-1/4"
3/16" x 6-1/4"
3/16" x 8-1/4"
3/16" x 10"
7/32" x 6-1/4"
USABLE LENGTH
Std. box
Std. Ctn.
4"
2"
4"
6"
7-1/2"
4"
25
25
25
25
25
25
500
450
500
450
300
500
65
DRI L L I NG
spline • HD straight shank
Spline
use in
Rotary hammer with Spline chuck
Size Range
3/8" x 8" to 2" x 23"
Spline Carbide Drill Bits are designed for use in a rotary hammer equipped with
a spline type chuck. The bits are manufactured to conform with ANSI Standard
B212.15 and can be used to drill in concrete, block, brick, and soft stone. Both
4-X Cutter and single tip head styles are available.
4-X cutter head spline drill bits
Cat. No.
Size
7017
7020
7021
7023
7028
7031
7033
7035
7036
7037
7043
7045
7049
7051
7053
7057
7059
7064
7066
7069
7072
7077
5/8" x 10"
5/8" x 16"
5/8" x 22"
5/8" x 27"
11/16" x 16"
3/4" x 10"
3/4" x 16"
3/4" x 22"
3/4" x 27"
3/4" x 36"
7/8" x 16"
7/8" x 22"
1" x 16"
1" x 22"
1" x 36"
1-1/8" x 16"
1-1/8" x 22"
1-1/4" x 16"
1-1/4" x 22"
1-1/4" x 36"
1-3/8" x 22"
1-1/2" x 22"
Usable Length
Std. Tube
5"
11"
17"
22"
11"
5"
11"
17"
22"
31"
11"
17"
11"
17"
31"
11"
17"
11"
17"
31"
17"
17"
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Usable Length
Std. Tube
5"
5"
11"
8"
5"
8"
11"
17"
22"
31"
5"
5"
8"
11"
17"
31"
8"
5"
11"
17"
22"
31"
11"
17"
31"
11"
17"
31"
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
single tip spline carabide drill bits
66
Cat. No.
Size
1401
1402
1403
1405
1407
1408
1409
1410
1412
1413
1415
1418
1419
1420
1421
1424
1427
1431
1433
1434
1436
1437
1443
1444
1446
1449
1450
1453
3/8" x 10"
3/8" x 13"
3/8" x 16"
7/16" x 13"
1/2" x 10"
1/2" x 13"
1/2" x 16"
1/2" x 22"
1/2" x 27"
1/2" x 36"
9/16" x 10"
5/8" x 10"
5/8" x 13"
5/8" x 16"
5/8" x 22"
5/8" x 36"
11/16" x 13"
3/4" x 10"
3/4" x 16"
3/4" x 22"
3/4" x 27"
3/4" x 36"
7/8" x 16"
7/8" x 22"
7/8" x 36"
1" x 16"
1" x 22"
1" x 36"
Cat. No.
Size
1457
1458
1464
1465
1470
1471
1477
1486
1490
1-1/8" x 16"
1-1/8" x 22"
1-1/4" x 16"
1-1/4" x 22"
1-3/8" x 16"
1-3/8" x 22"
1-1/2" x 22"
1-3/4" x 22"
2" x 22"
Usable Length
Std. Tube
11"
17"
11"
18"
11"
17"
17"
17"
17"
1
1
1
1
1
1
1
1
1
HD Straight Shank Bits
use in
Hammer Drill
Size Range
1/8" x 3" to 3/4" x 24"
Heavy Duty Straight Shank Carbide Bits are designed for use in a hammer drill
equipped with a 3 jaw Jacobs type chuck. The bits meet ANSI standards and can
be used to drill in concrete, block, brick, and soft stone.
hd straight shank bits
Cat. No.
Drill Size
0501
0503
0504
0505
0512
0513
0514
0516
0519
0522
0523
0525
0531
0532
0534
0538
0540
0545
0547
1/8" x 3"
5/32" x 6"
3/16" x 4"
3/16" x 6"
1/4" x 4"
1/4" x 6"
1/4" x 12"
1/4" x 24"
5/16" x 6"
3/8" x 6"
3/8" x 12"
3/8" x 24"
1/2" x 6"
1/2" x 12"
1/2" x 24"
5/8" x 6"
5/8" x 12"
3/4" x 6"
3/4" x 12"
Usable Length
Shank Size
Std. Pouch
2"
4"
2"
4"
2"
4"
7"
22"
4"
4"
10"
22"
4"
10"
22"
4"
10"
4"
10"
1/8"
5/32"
3/16"
3/16"
1/4"
1/4"
1/4"
1/4"
5/16"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
1/2"
1/2"
1/2"
1/2"
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
BULK PACK
Cat. No.
Drill Size
0593
0594
0595
1/4" x 4"
1/4" x 6"
3/8" x 6"
Bits Per Pack
25
25
10
Ig straight shank • "a" taper • rotary carbide • rebar cutter
use in
IG Straight Shank Bits
Rotary Only Drill
Size Range
use in
1/8" x 2-1/2" to 3/4" x 6"
Hammer Drill
Size Range
1/8" x 3" to 1" x 12"
Industrial Grade Straight Shank Carbide Bits are designed for use in a hammer
drill equipped with a 3 jaw Jacobs type chuck. The bits meet ANSI standards and
can be used to drill in concrete, block, brick, and soft stone.
IG straight shank bits
Cat. No.
Drill Size
0601
0604
0605
0612
0613
0614
0618
0619
0621
0622
0623
0625
0626
0631
0632
0635
0638
0640
0645
0647
0650
0654
1/8" x 3"
3/16" x 4"
3/16" x 6"
1/4" x 4"
1/4" x 6"
1/4" x 12"
5/16" x 4"
5/16" x 6"
3/8" x 4"
3/8" x 6"
3/8" x 12"
3/8" x 24"
7/16" x 6"
1/2" x 6"
1/2" x 12"
9/16" x 6"
5/8" x 6"
5/8" x 12"
3/4" x 6"
3/4" x 12"
7/8" x 12"
1" x 12"
BULK PACK
Cat. No.
Drill Size
0561
0562
0563
0564
0565
0566
3/16" x 4"
3/16" x 6"
1/4" x 4"
1/4" x 6"
3/8" x 6"
1/2" x 6"
Usable Length
Shank Size
2"
2"
4"
2"
4"
10"
2"
4"
2"
4"
10"
22"
4"
4"
10"
4"
4"
10"
4"
10"
10"
10"
1/8"
3/16"
3/16"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
1/4"
5/16"
5/16"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
1/2"
1/2"
1/2'
1/2"
Std. Pouch
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
fast spiral rotary carbide bits
Bits Per Pack
50
50
25
25
10
10
Rotary Hammer with "A" Taper Chuck or Adapter
Size Range
1/4" x 6" to 3/4" x 12"
“A” Taper Drill Bits are designed for use in a rotary hammer equipped with an
“A” Taper type chuck. The bits meet ANSI standards and can be used to drill in
concrete, block, brick, and soft stone.
"a" Taper bits
Drill Size
1/4" x 6"
Drill Size
8500
8506
8508
8512
8514
8560
8520
8526
8570
8530
1/8"
3/16"
1/4"
5/16"
3/8"
3/8"
1/2"
5/8"
5/8"
3/4"
Shank Size
Usable Length
Overall Length
Std. Tube
1/8"
3/16"
1/4"
1/4"
1/4"
1/4"
3/8"
1/2"
1/2"
1/2"
1-3/4"
1-3/4"
1-3/4"
2-1/2"
2-1/2"
4-1/2"
4"
4"
10-1/2"
4"
2-1/2"
3"
4"
4"
4"
6"
6"
6"
12"
6"
1
1
1
1
1
1
1
1
1
1
Cat. No.
Drill Size
8606
8608
3/16"
1/4"
Shank Size
Usable Length
Overall Length
Std. Tube
3/16"
1/4"
1-3/4"
1-3/4"
3"
4"
1
1
Rebar Cutter
Carbide Drill Bits
use in
Rotation-only drill with standard 1/2" Jacobs style chuck
Size Range
1/2" to 1-1/4" diameter
Rebar cutter bits provide a quick, easy method for drilling through mesh or reinforcing bars embedded in concrete when the drilled hole cannot be relocated.
The bits are used in the rotation only mode and are designed to fit in a standard
rotary drill motor with a 1/2" Jacobs style chuck.
When drilling with a hammer drill or rotary hammer, it is important to stop
drilling immediately when a standard carbide bit contacts steel reinforcing bar
or wire mesh. If the drilled hole cannot be relocated, a rebar cutter bit is used
to drill through the embedded steel. Insert the rebar cutter bit into the chuck
of a standard 1/2” rotary drill. Place the bit into the partially drilled hole until it
contacts the mesh or reinforcing bar. Drill through the embedded steel with the
rebar cutter bit. Once the bit has drilled through the steel, remove the debris
from the hole, then continue drilling with the standard carbide tipped bit using a
hammer drill or rotary hammer.
use in
0712
Cat. No.
deep flute rotary carbide bits
“A” Taper Drill Bits
Cat. No.
Rotary Carbide Bits are designed for use in a rotation only drill equipped with a
3 jaw Jacobs type chuck. The bits meet ANSI standards with a positive rake tip
and can be used to drill in soft or brittle masonry materials using rotation only.
Fast spiral flutes are for fast drilling in soft to medium masonry materials such as
block or brick. Deep fluted drills perform best in concrete where the wide fluting
helps clean concrete chips and dust from the hole.
DRI L L I NG
Rotary Carbide Drills
Usable Length
Std. Tube
4"
1
rebar cutter carbide drill bits
Cat. No.
Size
0845
0844
0846
0847
0849
0851
0853
0855
1/2" x 12"
9/16" x 12"
5/8" x 12"
11/16" x 12"
3/4" x 12"
7/8" x 12"
1" x 12"
1-1/4" x 12"
Usable Length
STD. Box
11"
11"
11"
11"
11"
11"
11"
11"
12
12
12
12
12
12
12
12
67
DRI L L I NG
HEAVY DUTY CHISELS • core bits
Heavy Duty Chisels
use in
Heavy Duty One and Two Piece Core Bits
Combination Rotary Hammer / Chipping Tool with a Spline, SDS-Max®
or 3/4" Hex Chuck
use in
Rotary Hammer with a Spline or SDS Max® chuck
Size Range
Bull Point, Flat, Scaling and Bushing
Size Range
Heavy Duty Chisels and accessories are designed for use in a combination rotary
hammer / chipping tool equipped with a Spline, SDS-Max, or 3/4" Hex chuck.
They can be used for chipping applications in concrete, block, brick, and soft stone.
heavy duty chisels
Cat. No.
Shank Type
Description
0950
0951
0952
0953
0954
0955
0959
0960
0965
0966
0967
0968
0969
0970
0974
0975
0982
0983
Spline
Spline
Spline
Spline
Spline
Spline
Spline
Spline
SDS-Max
SDS-Max
SDS-Max
SDS-Max
SDS-Max
SDS-Max
SDS-Max
SDS-Max
3/4" Hex
3/4" Hex
Bull Point Chisel 12"
Flat Chisel 1" x 12"
Scaling Chisel 1-1/2" x 12"
Scaling Chisel 2" x 12"
Ground Rod Driver 7/8” x 10-1/4"
Bushing Tool 1-3/4" x 9-1/4"
Scaling Chisel 1-1/2" x 12"
Scaling Chisel 2" x 12"
Ground Rod Driver 7/8" x 10-1/4"1
Bushing Tool 1-3/4" x 9-1/2"
Flat chisel 1" x 12"
Flat chisel 1" x 18"
1-1/2" to 5"
Heavy Duty Core Bits are designed for use in a rotary hammer equipped with
a spline or SDS-Max type chuck. The bits can be used to drill in concrete, block,
brick, and soft stone.
Std. Box
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
one piece spline core bits - heavy wall
Cat. No.
Drill Size
Description
0260*
2-5/8"
Hollow Core Bit Spline 2-5/8" x 22"
Std. Tube
1
One piece core bits are packaged with a centering bit and ejector pin.
one piece sds-max core bits - heavy wall
Cat. No.
Drill Size
Description
0284
2-5/8"
Hollow Core Bit SDS-Max 2-5/8" x 22
Std. Tube
1
One piece core bits are packaged with a centering bit and ejector pin.
Cups With External Male Rope Thread
two piece core bits - heavy wall
Cat. No.
Drill Size
Description
0570
0571
0572
0573
0575
0576
1-3/4"
2"
2-5/8"
3-1/8"
4"
5"
Hollow Core Bit 1-3/4" x 4"
Hollow Core Bit 2" x 4"
Versio Core Cutter 2-5/8" x 4"
Versio Core Cutter 3-1/8" x 4"
Versio Core Cutter 4" x 4"
Versio Core Cutter 5" x 4"
Std. Tube
1
1
1
1
1
1
Drive shanks with internal female Rope Thread
two piece core bits
Cat. No.
Shank Type
Description
0578
0582
0580
0590
Spline
Universal
SDS-Max
-
Adaptor
Extension
Adaptor
Centering Bit
68
Overall Length
Usable Length
Std. Tube
7"
11"(w/o flute)
7-3/4"
6"
2"
11"
2-3/4"
-
1
1
1
1
carbide warranty
Evaluation Criteria
Powers carbide tipped drill bits are warranted against failure due to
manufacturing defects. This warranty does not apply to failure due to normal
wear or where there is evidence of improper application or misuse.
Evaluation criteria
ANSI Standard B212.15
Damage
Powers carbide tipped drill bits are manufactured to conform with the American
National Standards Institute, Standard B212.15 as listed in the following table.
Powers anchors, unless otherwise noted, are designed to be installed in holes
drilled in the base material using carbide tipped bits meeting this specification.
Nominal Drill o.d.
ansi Standard
1/8"
5/32"
11/64"
3/16"
7/32"
1/4"
9/32"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
0.134-0.140"
0.165-0.171"
0.181-0.187"
0.198-0.206"
0.229-0.237"
0.260-0.268"
0.296-0.304"
0.327-0.335"
0.390-0.398"
0.458-0.468"
0.520-0.530"
0.582-0.592"
0.650-0.660"
nominal drill O.D.
ansi standard
11/16"
3/4"
27/32"
7/8"
15/16"
1"
1-1/8"
1-1/4"
1-3/8"
1-1/2"
1-5/8"
1-3/4"
2"
0.713-0.723"
0.775-0.787"
0.865-0.881"
0.905-0.917"
0.968-0.980"
1.030-1.042"
1.160-1.175"
1.285-1.300"
1.410-1.425"
1.535-1.550"
1.655-1.675"
1.772-1.792"
2.008-2.028"
Evaluation Procedure
The allowable wear differential is listed in the table below. Bits which are worn beyond the
differential have reached the maximum expected bit life and do not qualify for warranty.
Wear Differential (Inch)
3/16"
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
11/16"
0.008"
0.008"
0.012"
0.016"
0.020"
0.020"
0.024"
0.024"
0.024"
Drill Bit diameter (Inch)
Wear Differential (Inch)
3/4"
7/8"
1"
1-1/8"
1-1/4"
1-3/8"
1-1/2"
1-3/4"
2"
0.024"
0.028"
0.032"
0.036"
0.039"
0.043"
0.048"
0.048"
0.048"
Cause
Carbide Insert Lip is
Missing or Loose
Carbide Tip Fractured
Carbide Tip/Tool
Body Breakage
Carbide Cutting Edge
is Worn/Rounded
1/3
The following criteria is used to evaluate drill bits submitted for warranty. Warranty claims
for carbide tipped drill bits should be submitted by the distributor to the local Powers branch
from which the merchandise was purchased. Full or partial replacement of a drill bit is based
on the amount of wear differential as measured between front and rear portion of the flute
as shown below. To determine the wear differential, measure the diameter of flute at d1 and
d2. The variation between d1 and d2 is the differential.
Drill Bit diameter (Inch)
The following chart shows typical drill bit damage associated with warranty claims, the probable cause, and the warranty policy. Warranty replacement credit will be adjusted based on
the amount of drill bit wear. No replacement will be made for bits where the shank transition
is polished or where flutes are full of foreign material such as tar.
2/3
Loss of Carbide/Tool Tip
This is generally caused by poor brazing indicated by lack of
brazing material at theBase of the tip or voids. Failure usually
occurs within the first 10 to 20 holes.
Full/Partial Replacement based on wear.
DRI L L I NG
Carbide Drill Bit Warranty
Tip fractures will occur if reinforcing bars or other embedments
are struck when drilling into concrete or masonry. These failures
are easily identified because both the carbide insert and the
tool steel will be damaged.
No Warranty Replacement.
Tip fractures may also occur if the carbide insert is out of
tolerance, usually too hard. If this type of failure occurs, only the
carbide tip will be fractured.
A failure such as this indicates that the brazing may not have
been strong enough to resist the differences in thermal
expansion between the carbide tip and the tool steel.
If the cutting edge of the carbide tip is worn more than 2/3 of
its width, the bit has reached the end of its useful life.
A failure such as this indicates that the brazing may not have
been strong enough to resist the differences in thermal expansion between the carbide tip and the tool steel.
Shaft Breakage Behind Head Shaft breakage may occur if there is a defect in the tool steel.
This will be indicated by a notch which is evident in the fracture
area. Full/Partial Replacement based on wear.
Breakage may occur if the bit has been over torqued by jamming it in the hole. This is indicated by the lack of a notch and
an irregular / jagged fracture area.
Shaft Breakage Away
from Tool Head
Shaft Breakage Clogged Flutes
Shank Transition is Polished
Tool Holder Slots Worn
Shaft breakage away from the tool head may occur if there is a
defect in the tool steel. This will be indicated by a notch which is
evident in the fracture area.
Breakage in the shaft away from the head or tip area may also
occur if the bit has been over torqued by jamming it in the hole.
This is indicated by an irregular or jagged fracture area. No
notch is apparent.
The bit has been used to drill through plastic, tar, adhesive, etc.,
and the flutes have been clogged. This is an indication that the
bit could not clear dust and chips and broke from overload.
If the drill bit has been used to produce holes deeper than the
length of the flute, the area between the flutes and the upper
shank will become polished. Dust may also be packed into
the flutes.
Wear in the tool holder area indicates that the drill motor used
should be repaired or replaced.
69
•
•
Type 303/304 Stainless
•
•
•
•
A307
•
•
•
•
Grade 5
•
Coatings / Materials
&
screw s
Tapping
Screw
•
Self
Drilling
Machine
Bolt
•
Wood
Screw
Hanger
Bolt
•
Yellow Zinc Plated
Machine
Screw
Lag Bolt
Zinc Plated
Product
Cap
Screw
Carriage
Bolt
Screw and Bolt Selection Guide
Tap
Bolt
Bolts
SELECTION GUIDE
•
•
•
•
•
•
•
•
•
•
Type 316 Stainless
Brass
•
•
•
Grade 8
•
1/4"
•
•
•
5/16"
•
•
•
3/8"
•
•
•
1/2"
•
•
•
5/8"
3/4"
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
No 4
•
Diameter
No 6
•
•
•
No 8
•
•
•
•
No 10
•
•
•
•
No 12
•
•
•
•
No 14
•
•
•
•
4-40
•
6-32
•
8-32
•
10-24
•
10-32
•
•
•
•
•
No 7
•
12-24
Hex Head
•
•
Dome Head Square Neck
•
•
•
•
Head Style
Hex Washer Head
Round Head
•
Flat Head
•
Pan Head
•
Slotted
•
Phillips
•
Combo
•
•
•
Wafer
Sheet Metal
•
•
•
•
•
•
•
•
•
•
Wood
•
•
•
•
•
Some uses
Nylon
•
Plastic
Wood To Wood
•
•
•
Steel To Wood
•
•
•
•
•
•
•
•
•
•
•
•
Through Bolt
•
Bolt And Shield Anchors
•
•
•
Screw Anchors
70
•
•
Box
•
Jar
•
•
•
•
•
•
•
•
•
•
•
SELECTION GUIDE
•
•
•
•
•
•
•
•
•
•
•
Brass
•
Grade 2
Grade 5
•
Grade 8
•
•
•
•
•
•
•
•
•
BO LTS
•
•
•
•
•
•
No 6
•
•
•
•
No 8
•
•
•
•
No 10
•
•
•
•
No 12
•
•
•
•
Nickle Plated
•
No 14
Diameter
Fender
Washer
•
•
Finishing
Washer
•
•
•
SAE Flat
Washer
•
•
•
Rod
Coupler
•
Acorn
Nut
•
USS Flat
Washer
•
•
Split
Lock
Washer
Type 316 Stainless
•
Nylon
Insert
Locknut
•
Forged
Wing
Nut
Type 303/304 Stainless
Machine
screw
Nut
•
jam
Nut
•
Zinc Plated
Heavy
Nut
Finish
Nut
Yellow Zinc
&
Coatings / Materials
Product
SCREW S
Nut and Washer Selection Guide
•
6-32
•
•
•
8-32
•
•
•
10-24
•
•
•
10-32
•
•
•
12-24
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
3/16"
•
1/4"
•
•
•
•
5/16"
•
•
•
•
3/8"
•
•
•
•
•
•
•
1/2"
•
•
•
•
•
•
•
•
5/8"
•
•
•
•
•
•
•
•
3/4"
•
•
•
•
•
•
•
•
7/8"
•
•
•
•
•
•
1"
•
•
•
•
•
•
•
•
7/16"
1-1/8"
•
•
1-1/4"
•
Box
•
Jar
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
71
screw s
&
Bolts
Zinc products
Zinc Products
Zinc Hex Machine Bolts A307
Cat. No.
Size
001000
001001
001003
001005
001006
001007
001009
001053
001055
001057
001058
001059
001060
001061
001063
001065
001101
001103
001104
001105
001106
001107
001109
001111
001118
001141
001142
001143
001144
001145
001146
001147
001148
001149
001150
001151
001153
001182
001183
001184
001185
001186
001187
001188
001189
001190
001191
001192
1/4"-20 x 3/8"
1/4"-20 x 1/2"
1/4"-20 x 3/4"
1/4"-20 x 1"
1/4"-20 x 1-1/4"
1/4"-20 x 1-1/2"
1/4"-20 x 2"
3/8"-16 x 1/2"
3/8"-16 x 3/4"
3/8"-16 x 1"
3/8"-16 x 1-1/4"
3/8"-16 x 1-1/2"
3/8"-16 x 1-3/4"
3/8"-16 x 2"
3/8"-16 x 2-1/2"
3/8"-16 x 3"
1/2"-13 x 3/4"
1/2"-13 x 1"
1/2"-13 x 1-1/4"
1/2"-13 x 1-1/2"
1/2"-13 x 1-3/4"
1/2"-13 x 2"
1/2"-13 x 2-1/2"
1/2"-13 x 3"
1/2"-13 x 5-1/2"
5/8"-11 x 1"
5/8"-11 x 1-1/4"
5/8"-11 x 1-1/2"
5/8"-11 x 1-3/4"
5/8"-11 x 2"
5/8"-11 x 2-1/4""
5/8"-11 x 2-1/2"
5/8"-11 x 2-3/4"
5/8"-11 x 3"
5/8"-11 x 3-1/4
5/8"-11 x 3-1/2"
5/8"-11 x 4"
3/4"-10 x 1-3/4"
3/4"-10 x 2"
3/4"-10 x 2-1/4""
3/4"-10 x 2-1/2"
3/4"-10 x 2-3/4"
3/4"-10 x 3"
3/4"-10 x 3-1/4"
3/4"-10 x 3-1/2"
3/4"-10 x 3-3/4"
3/4"-10 x 4"
3/4"-10 x 4-1/2"
Made to order
•
•
•
•
•
•
•
•
u/m box qty. Ctn. Qty.
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
50
50
50
50
50
50
50
50
50
50
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
WT./UM
3000
2000
2000
2000
1000
1000
1000
1000
1000
1000
1000
1000
500
500
500
500
500
500
500
500
250
250
250
250
125
250
250
250
250
125
125
125
125
125
125
125
125
125
125
125
125
125
75
75
75
75
75
75
1.02
1.18
1.44
1.67
2.02
2.39
3.07
2.89
3.40
4.03
4.78
5.54
6.22
6.94
8.52
10.04
7.26
8.28
9.30
10.42
11.82
13.24
16.04
18.74
32.40
14.60
16.12
18.00
19.76
22.40
24.20
26.28
28.12
30.48
32.40
34.60
40.08
32.25
35.10
38.25
41.35
44.45
47.55
50.65
53.80
56.90
60.00
66.20
WT./UM
Zinc Tap Bolts A307
72
Cat. No.
Size
001408
001409
001410
001435
001436
001438
001440
001441
1/4"-20 x 3-1/2"
1/4"-20 x 4"
1/4"-20 x 4-1/2"
3/8"-16 x 3-1/2"
3/8"-16 x 4"
3/8"-16 x 5"
3/8"-16 x 6"
1/2"-13 x 3/4"
Made to order
•
•
•
•
•
C
C
C
C
C
C
C
C
100
100
100
50
50
50
50
50
500
500
500
250
250
250
250
500
4.44
4.88
5.48
10.52
11.68
14.04
16.44
7.28
Cat. No.
Size
001442
001443
001580
001444
001443
001446
001447
001448
001449
001451
001453
001477
001478
001479
001480
001483
001504
001506
001508
001510
001512
001514
1/2"-13 x 1"
1/2"-13 x 1-1/4"
1/2" -13 x 1-3/4"
1/2"-13 x 1-1/2"
1/2"-13 x 2"
1/2"-13 x 2-1/2"
1/2"-13 x 3"
1/2"-13 x 3-1/2"
1/2"-13 x 4"
1/2"-13 x 5"
1/2"-13 x 6"
5/8"-11 x 1-1/2"
5/8"-11 x 1-3/4"
5/8"-11 x 2"
5/8"-11 x 2-1/2"
5/8"-11 x 3"
3/4"-10 x 2"
3/4"-10 x 2-1/2"
3/4"-10 x 3"
3/4"-10 x 3-1/2"
3/4"-10 x 4"
3/4"-10 x 5"
Made to order
•
•
•
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
50
50
50
50
50
50
50
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
WT./UM
500
500
250
500
250
250
250
125
125
125
125
250
250
125
125
125
125
125
75
75
75
75
8.60
9.76
11.84
10.92
13.12
15.24
17.44
20.08
22.56
26.88
30.88
18.00
19.77
22.48
26.96
31.28
34.08
40.24
46.16
52.64
58.88
71.28
WT./UM
Zinc Cap Screws Grade 5
Cat. No.
Size
002000
002001
002003
002005
002006
002007
002009
002022
002024
002026
002027
002028
002030
002032
002034
002036
002038
002045
002047
002048
002049
002051
002053
002055
002057
002059
002085
002086
002087
002088
002089
002090
002091
002093
002095
002097
002098
002099
002101
002118
002119
1/4"-20 x 3/8"
1/4"-20 x 1/2"
1/4"-20 x 3/4"
1/4"-20 x 1"
1/4"-20 x 1-1/4"
1/4"-20 x 1-1/2"
1/4"-20 x 2"
5/16"-18 x 1/2"
5/16"-18 x 3/4"
5/16"-18 x 1"
5/16"-18 x 1-1/4"
5/16"-18 x 1-1/2"
5/16"-18 x 2"
5/16"-18 x 2-1/2"
5/16"-18 x 3"
5/16"-18 x 3-1/2"
5/16"-18 x 4"
3/8"-16 x 3/4"
3/8"-16 x 1"
3/8"-16 x 1-1/4"
3/8"-16 x 1-1/2"
3/8"-16 x 2"
3/8"-16 x 2-1/2"
3/8"-16 x 3"
3/8"-16 x 3-1/2"
3/8"-16 x 4"
1/2"-13 x 1"
1/2"-13 x 1-1/4"
1/2"-13 x 1-1/2"
1/2"-13 x 1-3/4"
1/2"-13 x 2"
1/2"-13 x 2-1/4"
1/2"-13 x 2-1/2"
1/2"-13 x 3"
1/2"-13 x 3-1/2"
1/2"-13 x 4"
1/2"-13 x 4-1/2"
1/2"-13 x 5"
1/2"-13 x 6"
5/8"-11 x 1"
5/8"-11 x 1-1/4"
Made to order
•
•
•
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
50
50
100
100
100
100
100
50
50
50
50
50
50
50
50
50
50
50
50
25
25
25
25
25
25
25
3000
2000
2000
2000
1000
1000
1000
2000
2000
1000
1000
1000
1000
500
500
500
500
1000
1000
1000
1000
500
500
500
250
250
500
500
500
250
250
250
250
250
125
125
125
125
125
250
250
1.03
1.14
1.41
1.67
2.01
2.38
3.07
1.82
2.33
2.74
3.23
3.82
4.82
5.95
6.91
8.00
8.98
3.40
4.03
4.78
5.54
6.94
8.52
10.04
11.51
13.06
8.29
9.38
10.42
11.83
13.25
14.64
16.05
18.75
21.50
24.10
26.60
29.60
35.10
14.63
16.12
Zinc Products
Made to order
•
•
•
•
•
•
•
•
•
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
20
20
250
250
125
125
125
125
125
125
75
75
75
125
125
125
125
75
75
75
75
75
75
60
60
WT./UM
18.00
19.77
22.10
26.30
30.50
34.60
38.90
43.50
47.20
51.91
57.29
28.70
34.40
36.60
40.30
46.00
48.90
52.40
58.50
64.50
70.80
76.90
83.00
Zinc Tap Bolts Grade 5
Cat. No.
Size
002605
002606
002607
002609
002611
002613
002648
002649
002651
002653
002655
002686
002687
002688
002689
002691
002693
002695
002697
002698
002699
002701
1/4"-20 x 1"
1/4"-20 x 1-1/4"
1/4"-20 x 1-1/2"
1/4"-20 x 2"
1/4"-20 x 2-1/2"
1/4"-20 x 3"
3/8"-16 x 1-1/4"
3/8"-16 x 1-1/2"
3/8"-16 x 2"
3/8"-16 x 2-1/2"
3/8"-16 x 3"
1/2"-13 x 1-1/4"
1/2"-13 x 1-1/2"
1/2"-13 x 1-3/4"
1/2"-13 x 2"
1/2"-13 x 2-1/2"
1/2"-13 x 3"
1/2"-13 x 3-1/2"
1/2"-13 x 4"
1/2"-13 x 4-1/2"
1/2"-13 x 5"
1/2"-13 x 6"
Made to order
•
•
•
•
•
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
50
50
50
50
50
50
50
50
25
25
25
25
25
WT./UM
2000
1000
1000
1000
1000
1000
1000
1000
500
500
500
500
500
250
250
250
250
125
125
125
125
125
1.67
2.01
2.36
3.07
3.75
4.35
4.78
5.54
6.94
8.52
10.04
9.96
10.42
11.84
13.26
16.06
18.76
21.52
24.12
26.60
29.60
35.12
WT./UM
BO LTS
5/8"-11 x 1-1/2"
5/8"-11 x 1-3/4"
5/8"-11 x 2"
5/8"-11 x 2-1/2"
5/8"-11 x 3"
5/8"-11 x 3-1/2"
5/8"-11 x 4"
5/8"-11 x 4-1/2"
5/8"-11 x 5"
5/8"-11 x 5-1/2"
5/8"-11 x 6"
3/4"-10 x 1-1/2"
3/4"-10 x 2"
3/4"-10 x 2-1/4"
3/4"-10 x 2-1/2"
3/4"-10 x 3"
3/4"-10 x 3-1/4
3/4"-10 x 3-1/2"
3/4"-10 x 4"
3/4"-10 x 4- 1/2"
3/4"-10 x 5"
3/4"-10 x 5-1/2"
3/4"-10 x 6"
&
Size
002120
002121
002122
002124
002126
002128
002130
002131
002132
002133
002134
002141
002143
002144
002145
002147
002148
002149
002151
002152
002153
002154
002155
SCREW S
Cat. No.
Yellow Zinc Cap Screws Grade 8
Cat. No.
Size
002301
002303
002305
002306
002307
002309
002310
002311
002313
002328
002330
002332
002333
002334
002335
002336
002338
002340
002353
002355
002357
002358
002359
002360
002361
002362
002363
002364
002365
002401
002403
002404
002405
002406
002407
002409
002411
002413
002415
1/4"-20 x 1/2"
1/4"-20 x 3/4"
1/4"-20 x 1"
1/4"-20 x 1-1/4"
1/4"-20 x 1-1/2"
1/4"-20 x 2"
1/4"-20 x 2-1/4"
1/4"-20 x 2-1/2"
1/4"-20 x 3 "
5/16"-18 x 1/2"
5/16"-18 x 3/4"
5/16"-18 x 1 "
5/16"-18 x 1-1/4"
5/16"-18 x 1-1/2"
5/16"-18 x 1-3/4"
5/16"-18 x 2"
5/16"-18 x 2-1/2"
5/16"-18 x 3"
3/8"-16 x 1/2"
3/8"-16 x 3/4"
3/8"-16 x 1"
3/8"-16 x 1-1/4"
3/8"-16 x 1-1/2"
3/8"-16 x 1-3/4"
3/8"-16 x 2"
3/8"-16 x 2-1/4""
3/8"-16 x 2-1/2"
3/8"-16 x 2-3/4"
3/8"-16 x 3"
1/2"-13 x 3/4"
1/2"-13 x 1"
1/2"-13 x 1-1/4"
1/2"-13 x 1-1/2"
1/2"-13 x 1-3/4"
1/2"-13 x 2"
1/2"-13 x 2-1/2"
1/2"-13 x 3"
1/2"-13 x 3-1/2"
1/2"-13 x 4"
Made to order
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
50
50
50
50
50
50
50
50
50
50
50
50
25
25
2000
2000
2000
2000
1000
1000
1000
1000
1000
1000
2000
2000
1000
1000
1000
1000
1000
500
500
1000
1000
1000
1000
500
500
250
250
250
250
500
500
500
500
250
250
250
250
125
125
WT./UM
1.18
1.44
1.44
1.74
2.08
2.43
3.12
3.46
3.81
4.50
1.99
2.41
2.83
3.37
3.91
4.45
4.99
6.06
7.14
2.93
3.55
4.86
5.64
6.42
7.19
7.97
8.74
9.52
10.30
8.10
9.22
10.34
11.59
12.97
14.35
17.12
19.87
22.63
25.39
Zinc Carriage Bolts A307
Cat. No.
Size
006062
006063
006064
006065
006067
006069
006071
006073
006075
006076
006077
006106
006108
006110
006112
006113
006114
3/8"-16 x 3/4"
3/8"-16 x 1"
3/8"-16 x 1-1/4"
3/8"-16 x 1-1/2"
3/8"-16 x 2"
3/8"-16 x 2-1/2"
3/8"-16 x 3"
3/8"-16 x 3-1/2"
3/8"-16 x 4"
3/8"-16 x 4-1/2"
3/8"-16 x 5"
1/2"-13 x 2-1/2"
1/2"-13 x 3"
1/2"-13 x 3-1/2"
1/2"-13 x 4"
1/2"-13 x 4-1/2"
1/2"-13 x 5"
Made to order
•
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
50
50
50
50
50
50
50
50
50
25
25
25
25
1000
1000
500
500
500
250
250
250
250
250
250
250
150
125
125
125
125
3.79
4.61
5.08
5.62
6.94
8.25
9.39
10.51
11.80
13.00
14.07
15.73
17.98
19.74
21.90
24.60
26.30
WT./UM
Zinc Lag Bolts
Cat. No.
Size
007001
007002
007003
007005
007006
007007
007008
007009
1/4" x 1"
1/4" x 1-1/4"
1/4" x 1-1/2"
1/4" x 2"
1/4" x 2-1/2"
1/4" x 3 "
1/4" x 3-1/2"
1/4" x 4"
Made to order
C
100 2000
1.48
C
100 2000
1.67
C
100 1000
1.83
C
100 1000
2.58
C
100 1000
3.00
C
100 1000
3.57
C
100
500
4.03
C
100
500
4.44
Table continues on next page
73
screw s
&
Bolts
Zinc products
Table continued from previous page
Cat. No.
Size
007014
007015
007016
007018
007019
007020
007021
007022
007027
007028
007029
007031
007032
007033
007034
007035
007036
007037
007039
007040
007041
007044
007045
007046
007047
007048
007049
007050
007051
007053
007056
5/16" x 1"
5/16" x 1-1/4"
5/16" x 1-1/2"
5/16" x 2"
5/16" x 2-1/2"
5/16" x 3"
5/16" x 3-1/2"
5/16" x 4"
3/8" x 1"
3/8" x 1-1/4"
3/8" x 1-1/2"
3/8" x 2"
3/8" x 2-1/2"
3/8" x 3"
3/8" x 3-1/2"
3/8" x 4"
3/8" x 4 1/2"
3/8" x 5"
3/8" x 6"
3/8" x 7"
3/8" x 8"
1/2"x 1-1/2"
1/2"x 2"
1/2" x 2-1/2"
1/2" x 3"
1/2" x 3-1/2"
1/2" x 4"
1/2" x 4-1/2"
1/2" x 5"
1/2" x 6"
1/2" x 8"
Made to order
•
•
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
•
•
•
100
100
100
100
100
100
100
50
100
100
100
100
50
50
50
50
50
50
50
50
50
50
50
50
50
25
25
25
25
25
25
1000
1000
1000
1000
500
500
500
250
1000
1000
1000
500
500
500
250
250
250
250
250
150
150
500
250
250
250
125
125
125
125
125
75
WT./UM
2.93
3.21
3.70
4.05
4.62
5.38
5.94
6.88
3.18
3.66
4.19
6.56
6.51
7.76
8.78
10.09
11.39
12.51
14.99
17.01
19.48
8.43
10.65
13.44
15.13
17.52
19.47
21.80
24.20
28.80
37.00
Acoustical Lag Screw Driver
Cat. No.
Size
008003
1/4"
Made to order
E
1
1
WT./UM
0.10
Acoustical Screws
Cat. No.
Size
008002J
008010J
008011J
1/4" x 3 Lag
1/4"x 2" Self Drilling
1/4" x 3-1/4" A Self Drilling
Made to order
C
C
C
100
50
50
WT./UM
1000
1000
500
2.26
0.97
1.55
WT./UM
Zinc Hanger Bolts
74
Cat. No.
Size
012000
012001
012002
012003
012020
012021
012022
012023
012024
1/4"-20 x 1-1/2"
1/4"-20 x 2"
1/4"-20 x 2-1/2"
1/4"-20 x 3"
3/8"-16 x 3"
3/8"-16 x 3-1/2"
3/8"-16 x 4"
3/8"-16 x 5"
3/8"-16 x 6"
Made to order
•
•
•
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
50
50
50
2000
2000
1000
1000
500
500
500
250
250
2.62
2.62
2.62
5.90
7.00
7.84
9.13
11.73
16.00
Zinc Serrated Flange Bolts
Hex Washer Head
Cat. No.
Size
016801
016802
016803
016804
016827
016829
016830
1/4"-20 x 3/4"
1/4"-20 x 1"
1/4"-20 x 1-1/4"
1/4"-20 x 1-1/2"
3/8"-16 x 3/4"
3/8"-16 x 1"
3/8"-16 x 1-1/4"
Cat. No.
Size
016831
016832
016845
3/8"-16 x 1-1/2"
3/8"-16 x 2"
1/2"-13 x 2"
Made to order
•
•
•
•
•
•
•
Made to order
•
•
•
C
C
C
C
C
C
C
WT./UM
1000
1000
1000
1000
1000
1000
1000
1.75
1.95
2.25
2.35
4.24
4.70
5.75
WT./UM
C
C
C
100
100
100
100
100
100
100
100
100
50
500
500
250
7.20
8.00
16.30
WT./UM
Zinc Tap Screws Pan Phillips Head
Cat. No.
Size
065006
065007
065008
065009
065010
065012
065013
065014
065015
065024
065025
065026
065027
065029
065030
065031
065033
065034
065035
065037
065038
065039
065041
065042
065043
065045
065046
065047
065048
065050
065052
065053
065054
065056
065057
065058
065059
065061
065063
065064
065065
065067
065068
065069
065070
#6 x 1/4" AB
#6 x 3/8" AB
#6 x 1/2" AB
#6 x 5/8" AB
#6 x 3/4" AB
#6 x 1" A
#6 x 1-1/4" A
#6 x 1-1/2" A
#6 x 2" A
#8 x 3/8" AB
#8 x 1/2" AB
#8 x 5/8" AB
#8 x 3/4" AB
#8 x 1" A
#8 x 1-1/4" A
#8 x 1-1/2" A
#8 x 2" A
#8 x 2-1/2" A
#8 x 3" A
#10 x 1/2" AB
#10 x 5/8" AB
#10 x 3/4" AB
#10 x 1" A
#10 x 1-1/4" A
#10 x 1-1/2" A
#10 x 2" A
#10 x 2-1/2" A
#10 x 3" A
#12 x 1/2" AB
#12 x 3/4" AB
#12 x 1" A
#12 x 1-1/4" A
#12 x 1-1/2" A
#12 x 2" A
#12 x 2-1/2" A
#12 x 3" A
#14 x 1/2" AB
#14 x 3/4" AB
#14 x 1" A
#14 x 1-1/4" A
#14 x 1-1/2" A
#14 x 2" A
#14 x 2-1/2" A
#14 x 3" A
#12 x 4" A
Made to order
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
4000
4000
4000
4000
4000
4000
4000
3000
3000
4000
4000
4000
4000
4000
3000
3000
3000
1000
1000
4000
4000
4000
3000
3000
3000
1000
1000
1000
4000
3000
3000
3000
3000
1000
1000
1000
3000
3000
3000
3000
3000
1000
1000
1000
1000
0.13
0.18
0.20
0.24
0.27
0.34
0.42
0.50
0.64
0.28
0.31
0.37
0.41
0.51
0.61
0.69
0.89
1.10
1.30
0.44
0.50
0.54
0.69
0.81
0.94
1.20
1.40
1.67
0.61
0.81
0.96
1.15
1.30
1.61
1.98
2.33
0.86
0.96
1.20
1.38
1.57
1.80
2.75
3.07
2.70
Zinc Products
#6 x 3/8" AB
#6 x 1/2" AB
#6 x 5/8" AB
#6 x 3/4" AB
#6 x 1" A
#6 x 1-1/4" A
#6 x 1-1/2" A
#6 x 2" A
#8 x 3/8" AB
#8 x 1/2" AB
#8 x 5/8"
#8 x 3/4" AB
#8 x 1" A
#8 x 1-1/4" A
#8 x 1-1/2" A
#8 x 2" A
#8 x 2-1/2" A
#8 x 3" A
#10 x 1/2" AB
#10 x 5/8" AB
#10 x 3/4" AB
#10 x 1" A
#10 x 1-1/4" A
#10 x 1-1/2" A
#10 x 1-3/4" A
#10 x 2" A
#10 x 2-1/2" A
#10 x 3" A
#12 x 1/2" AB
#12 x 3/4" AB
#12 x 1" A
#12 x 1-1/4" A
#12 x 1-1/2" A
#12 x 1-3/4" A
#12 x 2" A
#12 x 2-1/2" A
#12 x 3" A
#14 x 3/4" AB
#14 x 1" A
#14 x 1-1/4" A
#14 x 1-1/2" A
#14 x 1-3/4" A
#14 x 2" A
#14 x 2-1/2" A
#14 x 3" A
#12 x 4"
Made to order
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
4000
4000
4000
4000
4000
4000
3000
3000
4000
4000
4000
4000
4000
3000
3000
3000
1000
1000
4000
4000
4000
4000
3000
3000
3000
3000
3000
1000
4000
4000
3000
3000
3000
3000
1000
1000
1000
3000
3000
3000
3000
1000
1000
1000
1000
1000
WT./UM
0.13
0.17
0.19
0.23
0.31
0.38
0.45
0.61
0.18
0.24
0.30
0.34
0.44
0.53
0.65
0.84
1.04
1.24
0.33
0.38
0.45
0.57
0.72
0.85
0.95
1.07
1.32
1.57
0.56
0.65
0.80
0.98
1.09
1.29
1.49
1.90
2.31
0.89
1.09
1.33
1.52
1.75
1.97
2.42
2.87
3.08
Made to order
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
WT./UM
4000
3000
3000
3000
1000
1000
1000
1000
1000
3000
1000
1000
1000
1000
0.60
0.81
1.18
1.38
1.59
1.94
2.31
2.63
2.95
1.54
2.02
2.45
2.94
3.95
BO LTS
Size
066007
066008
066009
066010
066012
066013
066014
066015
066024
066025
066026
066027
066029
066030
066031
066033
066034
066035
066037
066038
066039
066041
066042
066043
066044
066045
066046
066047
066048
066050
066052
066053
066054
066055
066056
066057
066058
066061
066063
066064
066065
066066
066067
066068
066069
066074
#12 x 3/4"
#12 x 1"
#12 x 1-1/2"
#12 x 1-3/4"
#12 x 2"
#12 x 2-1/2"
#12 x 3"
#12 x 3-1/2"
#12 x "4
#14 x 1-1/2"
#14 x 2"
#14 x 2-1/2"
#14 x 3"
#14 x 4"
&
Cat. No.
Size
076083
076085
076087
076088
076089
076091
076092
076093
076094
076098
076100
076102
076103
076105
SCREW S
Zinc Tap Screws Flat Phillips Head
Cat. No.
Zinc Machine Screws Flat Phillips Head
Cat. No.
Size
080049
080064
080065
080066
080068
#10-24 x 4"
1/4"-20 x "4
1/4"-20 x 4-1/2"
1/4"-20 x 5"
1/4"-20 x 6"
Made to order
•
•
•
•
•
C
C
C
C
C
100
100
100
100
100
1000
500
500
500
500
WT./UM
2.41
4.25
4.75
5.33
6.27
Zinc Machine Screws Round Combo Head
(Slot/Phillips)
Cat. No.
Size
082067
082070
082071
082215
082217
082219
082259
082261
082263
#10-24 x 4"
#10-24 x 5"
#10-24 x 6"
1/4"-20 x 4"
1/4"-20 x 5"
1/4"-20 x 6"
3/8"-16 x 4"
3/8"-16 x 5"
3/8"-16 x 6"
Made to order
•
•
•
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
50
50
50
WT./UM
1000
1000
600
600
600
600
300
300
300
2.55
3.15
3.80
4.60
5.65
6.75
5.70
6.90
8.10
WT./UM
Zinc Eye Bolts with Nut
Zinc Wood Screws Flat Phillips Head
Cat. No.
Size
076046
076047
076048
076050
076070
076072
076073
076074
076076
076078
076079
#8 x 1/2"
#8 x 5/8"
#8 x 3/4"
#8 x 1"
#10 x 3/4"
#10 x 1"
#10 x 1-1/4"
#10 x 1-1/2"
#10 x 2"
#10 x 2-1/2"
#10 x 3"
Made to order
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
4000
4000
4000
4000
4000
4000
3000
3000
3000
1000
1000
WT./UM
0.24
0.29
0.34
0.46
0.47
0.61
0.78
0.92
1.19
1.56
1.84
Cat. No.
Size
084000
084006
084007
084008
084009
084010
084011
084018
084019
084020
084022
084023
084025
3/8"-16 x 2-1/2"
1/4"-20 x 2"
1/4"-20 x 2-1/2"
1/4"-20 x 3"
1/4"-20 x 4"
1/4"-20 x 5"
1/4"-20 x 6"
3/8"-16 x 4"
3/8"-16 x 5"
3/8"-16 x 6"
1/2"-13 x 6"
1/2"-13 x 8"
1/2"-13 x 12"
Made to order
•
•
•
•
•
C
C
C
C
C
C
C
C
C
C
C
C
C
25
100
100
100
100
50
50
25
25
25
20
20
20
250
1000
600
600
600
500
150
150
150
150
60
60
60
3.50
4.25
4.85
5.45
6.45
3.5
4.0
4.50
5.05
5.70
8.65
10.45
14.10
75
screw s
&
Bolts
Zinc products
Zinc Flat Washers uss Pack
Zinc Machine Screws Truss Combo
Cat. No.
Size
085215
1/4"-20 x 3
Made to order
•
C
100
1000
WT./UM
3.70
Zinc Self Drilling Screws Hex Washer Head
Cat. No.
Size
135007M
135038
135815
#8-18 x 1/2" #2
#14 x 4"
#10 x 3/4" High Head
Made to order
•
C
C
C
100
100
5000
4000
1000
0
Cat. No.
Size
042001
042002
042003
042004
042005
042006
042008
042009
042010
042011
042012
042013
3/16"
1/4"
5/16"
3/8"
7/16"
1/2"
5/8"
3/4"
7/8"
1"
1-1/8"
1-1/4"
Made to order
•
•
•
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
50
25
25
25
10
10
4000
4000
3000
2000
1000
1000
500
250
250
250
100
100
WT./UM
0.30
0.70
1.10
1.50
2.40
3.90
7.70
11.00
15.30
18.80
22.20
26.00
WT./UM
0.36
5.00
0.65
Zinc Yellow Flat Washers uss Grade 8
Zinc Zip Point Screws Wafer Head
Cat. No.
Size
138325
138327
138329
138725
138727
138737
#8 x 1/2"
#8 x 3/4"
#8 x 1"
#8 x 1/2"
#8 x 3/4"
#8 x 3"
Made to order
•
C 10000
C 10000
C 5000
C 5000
C 10000
C 1000
WT./UM
0
0
0
0
0
0
0.34
0.43
0.53
0.53
0.45
1.36
WT./UM
Size
039001
039002
039003
039004
039006
039008
039009
039010
039011
3/16"
1/4"
5/16"
3/8"
1/2"
5/8"
3/4"
7/8"
1"
Made to order
•
•
•
•
Size
045002
045003
045004
045005
045006
045008
045009
045010
045011
045013
1/4"
5/16"
3/8"
7/16"
1/2"
5/8"
3/4"
7/8"
1"
1-1/4"
Made to order
•
•
•
•
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
50
25
25
25
10
4000
3000
2000
1000
1000
500
250
250
250
100
WT./UM
0.67
1.11
1.49
2.44
3.85
7.70
11.00
15.30
18.80
23.40
Zinc Yellow Flat Washers SAE Grade 8
Zinc Flat Washers uss 5 lbs
Cat. No.
Cat. No.
E
E
E
E
E
E
E
E
E
5
5
5
5
5
5
5
5
5
50
50
50
50
50
50
50
50
50
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
Cat. No.
Size
045022
045023
045024
045025
045026
045028
045029
045030
045031
1/4"
5/16"
3/8"
7/16"
1/2"
5/8"
3/4"
7/8"
1"
Made to order
•
•
•
•
•
•
•
•
•
C
C
C
C
C
C
C
C
C
100
100
100
100
100
50
50
25
25
4000
4000
4000
3000
2000
1000
500
250
250
WT./UM
0.45
0.52
0.72
0.95
1.83
2.77
4.74
1.40
2.20
Zinc Flat Washers uss 50 lbs
76
Cat. No.
Size
041001
041002
041003
041004
041005
041006
041008
041009
041010
041011
041012
041013
3/16"
1/4"
5/16"
3/8"
7/16"
1/2"
5/8"
3/4"
7/8"
1"
1-1/8"
1-1/4"
Made to order
•
•
box qty. Ctn. Qty.
50
50
50
50
50
50
50
50
50
50
50
50
0
0
0
0
0
0
0
0
0
0
0
0
WT./UM
50.00
50.00
50.00
50.00
50.00
50.00
50.00
50.00
50.00
50.00
50.00
50.00
Zinc Fender Washers 50 lbs
Cat. No.
Size
046502
046503
046504
046505
046506
046507
3/16" x 1"
3/16" x 1-1/4"
1/4" x 1"
1/4" x 1-1/4"
1/4" x 1-1/2"
5/16" x 1-1/4"
Made to order
E
E
E
E
E
E
50
50
50
50
50
50
0
0
0
0
0
0
WT./UM
50.00
50.00
50.00
50.00
50.00
50.00
Zinc Products
Size
046508
046509
046510
046511
046512
5/16" x 1-1/2"
3/8" x 1-1/4"
3/8" x 1-1/2"
1/2"x 1-1/2"
1/2"x 2"
Made to order u/m
box qty. Ctn. Qty. WT./UM
E
E
E
E
E
50
50
50
50
50
0
0
0
0
0
50.00
50.00
50.00
50.00
50.00
Zinc Neoprene Sealing Washers
446515
46004MB
46005MB
46009MB
46015MB
3/16" x 3/4"
1/4" x 1"
1/4" x 1-1/4"
3/8" x 1-1/4"
3/8" x 1"
Made to order
C
-
4000
3000
2000
2000
2000
WT./UM
34.35
1.00
1.60
2.20
1.90
Cat. No.
Size
135998
135999
136000
#10
#12
#14
Made to order
C
C
C
100
100
100
WT./UM
4000
4000
4000
0.30
0.40
0.40
WT./UM
BO LTS
Size
&
Zinc Fender Washers
Cat. No.
SCREW S
Cat. No.
Plain Flat Washers uss Pack
Zinc Split Lock Washers Bulk*
Cat. No.
Size
Made to order
047006B
1/4"
C
100
047007B
5/16"
C
100
047008B
3/8"
C
100
047010B
1/2"
C
100
• Zinc Split Lock Washers also available in jars also, please see page 83
WT./UM
4000
4000
4000
3000
0.22
0.38
0.60
1.30
Size
047806
047807
047808
047810
047812
047813
047814
047815
1/4"
5/16"
3/8"
1/2"
5/8"
3/4"
7/8"
1"
Made to order
•
•
C
C
C
C
C
C
C
C
100
100
100
100
100
100
50
50
4000
4000
4000
3000
1000
1000
500
500
Size
342002
342004
342006
342008
342009
1/4"
3/8"
1/2"
5/8"
3/4"
Made to order
•
C
C
C
C
C
100
100
100
50
25
4000
2000
1000
500
250
0.50
1.46
3.35
3.88
2.60
WT./UM
Zinc Finished Hex Nuts
Zinc Yellow Split Lock Washers Grade 8
Cat. No.
Cat. No.
WT./UM
0.22
0.38
0.60
1.30
2.40
4.00
6.00
8.80
Cat. No.
Size
016001
016002
016003
016005
016007
016008
016009
016010
016012
1/4"-20
5/16 -18
3/8"-16
1/2"-13
5/8"-11
3/4"-10
7/8"-9
1"-8
1-1/4"-7
Made to order
C
C
C
C
C
C
C
C
C
100
100
100
50
50
25
10
10
10
4000
3000
2000
1000
500
250
200
100
100
0.68
1.02
1.49
3.60
7.11
11.80
17.67
26.60
51.70
WT./UM
Zinc Finished Hex Nuts Bulk
Nickle Finishing Washers
Cat. No.
Size
049002
049003
049004
049005
049006
No. 6
No. 8
No. 10
No. 12
No. 14
Made to order
•
•
•
•
C
C
C
C
C
100
100
100
100
100
4000
4000
4000
4000
3000
WT./UM
0.08
0.11
0.14
0.21
0.27
Cat. No.
Size
017001
017002
017003
017005
017006
017007
017008
017009
1/4"-20
5/16"-18
3/8"-16
1/2"-13
5/8"-11
3/4"-10
7/8"-9
1"-8
Made to order
C
C
C
C
C
C
C
C
9000
6000
4000
2200
1800
800
500
300
0
0
0
0
0
0
0
0
0.68
1.02
1.49
2.75
3.60
7.11
11.80
17.67
WT./UM
Zinc Finished Hex Nuts NF
Cat. No.
Size
018001
018002
018003
018004
018005
018007
018008
018012
1/4"-28
5/16"-24
3/8"-24
7/16"-20
1/2"-20
5/8"-18
3/4"-16
1-1/4"-12
Made to order
•
•
•
•
•
•
•
•
100
100
100
100
50
50
25
10
4000
3000
2000
1000
1000
500
250
100
0.68
1.02
1.49
2.75
3.60
7.11
11.80
51.70
77
screw s
&
Bolts
Zinc products
Zinc Serrated Flange Nuts
Cat. No.
Size
016498
016499
016500
016502
016505
016507
1/4"-20
5/16"-18
3/8"-16
1/2"-13
5/8"-11
3/4"-1
Made to order
•
•
C
C
C
C
C
C
100
100
100
50
50
25
WT./UM
3000
3000
2000
1000
500
250
0.90
1.23
1.78
4.40
8.80
13.70
WT./UM
Zinc Heavy Hex Nuts
Cat. No.
Size
021001
021002
021003
021005
021006
021007
021008
021009
1/4"-20
5/16"-18
3/8"-16
1/2"-13
5/8"-11
3/4"-10
7/8"-9
1"-8
Made to order
C
C
C
C
C
C
C
C
100
100
100
50
50
25
25
10
3000
2000
1000
500
250
250
100
100
1.16
1.72
3.20
6.54
11.90
19.30
29.70
42.50
WT./UM
Zinc K-Lock Nuts
Cat. No.
Size
023050
023051
023052
023053
023054
023055
6-32
8-32
10-32
10-24
1/4"-20
5/16"-18
Made to order
•
•
•
•
•
•
C
C
C
C
C
C
100
100
100
100
100
100
WT./UM
4000
4000
4000
4000
4000
3000
0.25
0.41
0.50
0.48
0.84
1.10
WT./UM
Yellow Zinc Hex Nuts NC Grade 8
Cat. No.
Size
024001
024002
024003
024005
024007
024008
024009
024010
1/4"-20
5/16"-18
3/8"-16
1/2"-13
5/8"-11
3/4"-10
7/8"-9
1"-8
Made to order
•
•
C
C
C
C
C
C
C
C
100
100
100
50
50
25
10
10
4000
3000
2000
1000
500
250
200
100
0.68
1.02
1.49
3.60
7.11
11.80
17.54
26.40
WT./UM
Zinc Heavy Hex Nuts Bulk
Cat. No.
Size
421005
421008
1/2"-13
7/8"-9
Made to order
C
C
1000
220
0
0
6.54
29.70
Zinc Nylon Insert Locknuts
Zinc Jam Hex Nuts
Cat. No.
Size
022001
022002
022003
022005
022006
022007
1/4"-20
5/16"-18
3/8"-16
1/2"-13
5/8"-11
3/4"-10
Made to order
•
•
•
•
•
•
C
C
C
C
C
C
100
100
100
50
25
25
WT./UM
4000
3000
2000
1000
500
250
0.52
0.77
1.05
3.46
4.93
7.70
WT./UM
Cat. No.
Size
028002
028003
028004
028005
028006
028007
028008
028010
028012
028013
#6-32 NM
#8-32 NM
#10-24 NM
#10-32 NM
1/4"-20 NE
5/16"-18 NE
3/8"-16 NE
1/2"-13 NE
5/8"-11 NE
3/4"-10 NE
Made to order
•
•
•
•
•
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
50
50
25
4000
4000
4000
4000
4000
3000
2000
500
500
250
0.25
0.41
0.48
0.48
0.84
1.10
1.76
4.10
8.55
12.29
WT./UM
Zinc Hex Nuts NC Grade 5
78
Cat. No.
Size
023001
023002
023003
023005
023006
023007
1/4"-20
5/16"-18
3/8"-16
1/2"-13
5/8"-11
3/4"-10
Made to order
C
C
C
C
C
C
100
100
100
50
50
25
4000
3000
2000
1000
500
250
0.68
1.02
1.49
3.60
7.12
11.80
Yellow Zinc Nylon Insert Locknuts
NC Grade 8
Cat. No.
Size
028806
028807
028808
028810
028812
028813
1/4"-20 NE
5/16"-18 NE
3/8"-16 NE
1/2"-13 NE
5/8"-11 NE
3/4"-10 NE
Made to order
•
•
•
•
•
•
C
C
C
C
C
C
100
100
100
50
50
25
4000
3000
2000
500
500
250
0.84
1.10
1.76
4.10
8.56
12.30
Zinc Products
1/4"-28 NE
5/16"-24 NE
3/8"-24 NE
1/2"-20 NE
Made to order
•
•
•r
•
C
C
C
C
100
100
100
50
WT./UM
4000
3000
2000
500
0.84
1.10
1.76
4.30
WT./UM
Nickle Acorn Nuts
Cat. No.
Size
029001
029002
029003
029005
1/4"-28 NE
5/16"-24 NE
3/8"-24 NE
1/2"-20 NE
Made to order
•
•
•
•
C
C
C
C
100
100
100
50
4000
3000
2000
500
0.84
1.10
1.76
4.30
Zinc Economy Rod Coupling Nuts
Cat. No.
Size
030001
030002
030003
030004
030005
030006
030007
030009
030010
030011
030012
030013
#6-32
#8-32
#10-24
#10-32
1/4"-20 x 3/8" x 7/8"
5/16"-18 x 7/16" x 7/8"
3/8"-16 x 1/2" x 1-1/8"
1/2"-13 x 5/8" x 1-1/4"
5/8"-11 x 13/16" x 2-1/8"
3/4"-10 x 1" x 2-1/4"
7/8"-9 x 1-1/4" x 2-1/2"
1"-8 x 1-1/4" x 2-1/2"
Made to order
•
•
•
•
•
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
50
25
25
10
10
4000
3000
3000
3000
2000
1000
1000
500
250
125
100
100
WT./UM
0.50
1.10
1.00
1.00
1.90
2.30
3.60
8.24
30.87
44.10
57.32
45.33
BO LTS
Size
029001
029002
029003
029005
&
Cat. No.
SCREW S
Zinc Nylon Insert Locknuts NF
Zinc Reducing Rod Coupling Nuts
Zinc Wing Nuts Forged
Cat. No.
Size
033003
033004
033005
033006
033007
033008
#10-24
#10-32
1/4"-20
5/16"-18
3/8"-16
1/2"-13
Made to order
•
•
•
C
C
C
C
C
C
100
100
100
100
100
50
4000
4000
4000
2000
1000
500
WT./UM
0.75
0.75
1.30
2.30
3.70
8.80
Cat. No.
Size
030016
030017
030018
030019
030021
030023
3/8"-16 - 1/4"-20
1/2"-13 - 3/8"-16
5/8"-11 - 1/2"-13
3/4"-10 - 1/2"-13
3/4"-10 - 5/8"-11
3/8"-16 - 5/16"-18
Made to order
•
•
C
C
C
C
C
C
50
50
25
25
25
50
WT./UM
1000
500
250
250
250
1000
3.92
6.90
11.70
13.50
21.70
3.92
WT./UM
Zinc Long Rod Coupling Nuts
Plain Finished Hex Nuts
Cat. No.
Size
316003
3/8"-16
Made to order
C
100
WT./UM
2000
1.50
WT./UM
Cat. No.
Size
030050
030052
030053
1/4"-20 x 7/16" x 1-3/4"
3/8"-16 x 9/16" x 1-3/4"
1/2"-13 x 11/1"6 x 1-3/4"
Made to order
C
C
C
100
50
50
500
250
250
5.70
8.03
14.77
Plain Finished Heavy Hex Nuts
Cat. No.
Size
321001
321003
321005
321006
321007
1/4"-20
3/8"-16
1/2"-13
5/8"-11
3/4"-10
Made to order
•
C
C
C
C
C
100
100
50
25
25
3000
2000
500
250
250
0.75
2.91
2.99
2.82
4.63
79
screw s
&
Bolts
Zinc products • Stainless steel Products
Stainless steeL Products
Stainless Steel Machine Bolt
Cat. No.
Size
801001
801002
801003
801005
801006
801007
801008
801009
801011
801013
801019
801021
801028
801030
801032
801033
801034
801036
801037
801038
801040
801053
801054
801055
801057
801058
801059
801061
801063
801065
801067
801069
801104
801105
801107
801109
801111
801113
801115
801116
801117
801119
801121
801123
801145
801147
801149
801183
801187
801189
801191
801192
1/4"-20 x 1/2"
1/4"-20 x 5/8"
1/4"-20 x 3/4"
1/4"-20 x 1"
1/4"-20 x 1-1/4"
1/4"-20 x 1-1/2"
1/4"-20 x 1-3/4"
1/4"-20 x 2"
1/4"-20 x 2-1/2"
1/4"-20 x 3"
1/4"-20 x 5
1/4"-20 x 6"
5/16"-18 x 1/2"
5/16"-18 x 3/4"
5/16"-18 x 1"
5/16"-18 x 1-1/4"
5/16"-18 x 1-1/2"
5/16"-18 x 2"
5/16"-18 x 20-1/4"
5/16"-18 x 2-1/2"
5/16"-18 x 3"
3/8"-16 x 1/2"
3/8"-16 x 5/8"
3/8"-16 x 3/4"
3/8"-16 x 1"
3/8"-16 x 1-1/4"
3/8"-16 x 1-1/2"
3/8"-16 x 2"
3/8"-16 x 2-1/2"
3/8"-16 x 3"
3/8"-16 x 3-1/2"
3/8"-16 x 4"
1/2"-13 x 1-1/4"
1/2"-13 x 1-1/2"
1/2"-13 x 2"
1/2"-13 x 2-1/2"
1/2"-13 x 3"
1/2"-13 x 3-1/2"
1/2"-13 x 4"
1/2"-13 x 4-1/2"
1/2"-13 x 5"
1/2"-13 x 6"
1/2"-13 x 7"
1/2"-13 x 8"
5/8"-11 x 2"
5/8"-11 x 2-1/2"
5/8"-11 x 3
3/4"-10 x 2"
3/4"-10 x 3"
3/4"-10 x 3-1/2"
3/4"-10 x 4"
3/4"-10 x 4-1/2"
Made to order
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
50
50
50
50
50
50
50
50
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
2000
2000
2000
2000
1000
1000
1000
1000
1000
1000
500
500
2000
2000
1000
1000
1000
1000
500
500
500
1000
1000
1000
1000
1000
1000
500
500
500
250
250
500
250
250
250
125
125
125
125
125
75
75
75
125
125
125
125
75
75
75
75
WT./UM
1.18
1.31
1.44
1.67
2.02
2.39
2.70
3.07
3.75
4.35
7.35
8.39
1.82
2.33
2.74
3.23
3.82
4.82
5.65
5.39
5.95
2.89
3.16
3.40
4.03
4.78
5.54
6.94
8.52
10.04
11.50
13.06
10.42
13.24
16.04
18.74
21.48
21.48
24.08
26.60
29.60
39.40
35.08
44.80
22.40
26.28
30.48
35.10
47.55
53.80
15.00
16.40
80
Size
806013
806015
806017
1/4" x 20 x 3/4"
1/4" x 20 x 1"
1/4"-20 x 1-1/2"
Made to order
•
C
C
C
Size
806019
806021
806023
806025
806027
806029
806037
806039
806041
806043
806045
806063
806064
806065
806067
806069
806071
806073
806104
1/4"-20 x 2"
1/4"-20 x 2-1/2"
1/4"-20 x 3"
1/4"-20 x 3-1/2"
1/4"-20 x 4"
1/4"-20 x 5"
5/16"-18 x 1"
5/16"-18 x 1-1/2"
5/16"-18 x 2"
5/16"-18 x 2-1/2"
5/16"-18 x 3-1/2"
3/8"-16 x 1"
3/8"-16 x 1-1/4"
3/8"-16 x 1-1/2"
3/8"-16 x 2"
3/8"-16 x 2-1/2"
3/8"-16 x 3"
3/8"-16 x 3-1/2"
1/2"-13 x 2"
Made to order
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
50
50
50
50
50
WT./UM
1000
1000
500
500
500
500
1000
1000
500
500
500
1000
500
500
500
250
250
250
250
2.76
3.26
3.78
4.45
4.89
6.05
2.95
3.81
4.52
5.46
6.50
4.61
5.08
5.62
6.94
8.25
9.39
10.51
13.20
WT./UM
Stainless Steel Lag Bolts
Cat. No.
Size
807001
807002
807003
807005
807006
807007
807008
807009
807011
807013
807016
807018
807020
807021
807022
807029
807031
807032
807033
807034
807035
807037
807039
807044
807045
807047
807049
807051
807053
807056
1/4" x 1"
1/4" x 1-1/4"
1/4" x 1-1/2"
1/4" x 2"
1/4" x 2-1/2"
1/4" x 3"
1/4" x 3-1/2"
1/4" x 4"
1/4" x 5"
1/4" x 6"
5/16" x 1-1/2"
5/16" x 2"
5/16" x 3"
5/16" x 3-1/2"
5/16" x 4"
3/8" x 1-1/2"
3/8" x 2"
3/8" x 2-1/2"
3/8" x 3"
3/8" x 3-1/2"
3/8" x 4"
3/8" x 5"
3/8" x 6"
1/2" x 1-1/2"
1/2" x 2"
1/2" x 3"
1/2" x 4"
1/2" x 5"
1/2" x 6"
1/2" x 8"
Made to order
•
•
•
•
•
•
•
•
•
•
•
•
•
•
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
50
100
100
50
50
50
50
50
50
50
50
50
25
25
25
25
2000
2000
1000
1000
1000
0
500
500
500
500
1000
1000
500
500
250
1000
500
500
500
250
250
250
250
500
250
250
125
125
125
75
1.48
1.67
1.83
2.58
3.00
3.57
4.03
4.44
5.46
6.59
3.70
4.05
5.38
6.01
6.88
4.19
6.56
6.51
7.76
8.78
10.09
12.51
14.99
8.43
10.65
15.13
19.47
24.20
28.80
9.55
WT./UM
Stainless Steel Machine Screws
Pan Phillips Head
Stainless Steel Carriage Bolts
Cat. No.
Cat. No.
100
100
100
2000
2000
1000
WT./UM
1.55
1.70
2.19
Cat. No.
Size
883174
3/8"-16 x 1-3/4"
Made to order
C
100
1000
Stainless steel Products
#6 x 3/8 AB
#6 x 1/2" AB
#6 x 5/8 AB
#6 x 3/4" AB
#6 x 1" A
#6 x 1-1/4" A
#6 x 1-1/2" A
#6 x 2" A
#8 x 3/8" AB
#8 x 1/2" AB
#8 x 5/8" AB
#8 x 3/4" AB
#8 x 1" A
#8 x 1-1/4" A
#8 x 1-1/2" A
#8 x 2" A
#8 x 2-1/2" A
#8 x 3" A
#10 x 3/8" AB
#10 x 1/2" AB
#10 x 3/4" AB
#10 x 1" A
#10 x 1-1/4" A
#10 x 1-1/2" A
#10 x 2" A
#10 x 2-1/2" A
#10 x 3" A
#12 x 1/2" AB
#12 x 3/4" AB
#12 x 1" A
#12 x 1-1/4" A
#12 x 1-1/2" A
#12 x 1-3/4" A
#12 x 2" A
#12 x 2-1/2" A
#12 x 3" A
#14 x 3/4" AB
#14 x 1" A
#14 x 1-1/4" A
#14 x 1-1/2" A
#14 x 2" A
#14 x 2-1/2" A
#14 x 3" A
Made to order
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
4000
4000
4000
4000
4000
4000
3000
3000
4000
4000
4000
4000
4000
3000
3000
3000
1000
1000
4000
4000
4000
4000
3000
3000
1000
1000
1000
4000
3000
3000
3000
3000
1000
1000
1000
1000
3000
3000
3000
1000
1000
1000
1000
WT./UM
0.13
0.18
0.20
0.24
0.27
0.34
0.42
0.50
0.64
0.28
0.31
0.37
0.41
0.51
0.61
0.69
0.89
1.10
1.30
0.44
0.50
0.54
0.69
0.81
0.94
1.20
1.40
1.67
0.61
0.81
0.96
1.15
1.30
1.61
1.98
2.33
0.86
0.96
1.20
1.38
1.57
1.80
2.75
Stainless Steel Tapping Screws
Flat Phillips Head
Cat. No.
Size
866003
866004
866005
866008
866009
866010
866012
866013
866014
866015
866024
#4 x 1/2" AB
#4 x 5/8 AB
#4 x 3/4" AB
#6 x 1/2" AB
#6 x 5/8 AB
#6 x 3/4" AB
#6 x 1" A
#6 x 1-1/4" A
#6 x 1-1/2" A
#6 x 2" A
#8 x 3/8" AB
Made to order
•
•
•
•
•
•
•
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
4000
4000
4000
4000
4000
4000
4000
4000
3000
3000
4000
WT./UM
0.10
0.10
0.15
0.15
0.15
0.30
0.30
0.35
0.40
0.60
0.25
Made to order
•
•
•
•
•
•
•
•
•
•
•
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
WT./UM
4000
4000
4000
4000
3000
3000
3000
3000
1000
1000
4000
4000
4000
3000
3000
3000
3000
1000
1000
3000
3000
3000
1000
1000
1000
1000
3000
3000
3000
1000
1000
1000
1000
1000
0.25
0.25
0.40
0.40
0.50
0.55
0.70
0.89
1.05
1.30
0.30
0.40
0.5
0.65
0.75
1.05
1.10
1.35
1.63
0.80
1.05
1.10
1.30
1.50
1.85
2.20
0.85
1.10
1.30
1.50
2.00
2.45
2.10
2.10
WT./UM
BO LTS
Size
865007
865008
865009
865010
865012
865013
865014
865015
865024
865025
865026
865027
865029
865030
865031
865033
865034
865035
865036
865037
865039
865041
865042
865043
865045
865046
865047
865048
865050
865052
865053
865054
865055
865056
865057
865058
865061
865063
865064
865065
865067
865068
865069
#8 x 1/2" AB
#8 x 5/8" AB
#8 x 3/4" AB
#8 x 1" A
#8 x 1-1/4" A
#8 x 1-1/2" A
#8 x 1-3/4" A
#8 x 2" A
#8 x 2-1/2" A
#8 x 3" A
#10 x 1/2" AB
#10 x 3/4" AB
#10 x 1" A
#10 x 1-1/4" A
#10 x 1-1/2" A
#10 x 1-3/4" A
#10 x 2" A
#10 x 2-1/2" A
#10 x 3" A
#12 x 1" A
#12 x 1-1/4" A
#12 x 1-1/2" A
#12 x 1-3/4" A
#12 x 2" A
#12 x 2-1/2" A
#12 x 3" A
#14 x 3/4" AB
#14 x 1" A
#14 x 1-1/4" A
#14 x 1-1/2" A
#14 x 2" A
#14 x 2-1/2" A
#14 x 3" A
#10 x 4"
&
Cat. No.
Size
866025
866026
866027
866029
866030
866031
866032
866033
866034
866035
866037
866039
866041
866042
866043
866044
866045
866046
866047
866052
866053
866054
866055
866056
866057
866058
866061
866063
866064
866065
866067
866068
866069
866071
SCREW S
Stainless Steel Tapping Screws
Pan Phillips Head
Cat. No.
Flat Phillips Head
Cat. No.
Size
880004
880008
880010
880012
880015
880016
880018
880020
880027
880028
880030
880032
880034
880038
880040
880042
880044
880045
880046
880048
880049
880051
880053
880055
880056
880057
880059
#6-32 x 1/2"
#6-32 x 1"
#6-32 x 1-1/2"
#6-32 x 2"
#8-32 x 3/8"
#8-32 x 1/2"
#8-32 x 3/4"
#8-32 x 1"
#10-24 x 3/8"
#10-24 x 1/2"
#10-24 x 3/4"
#10-24 x 1"
#10-24 x 1-1/2"
#10-24 x 3"
#10-32 x 1/2"
#10-32 x 3/4"
#10-32 x 1"
#10-32 x 1-1/4"
#10-32 x 1-1/2"
#10-32 x 2"
#10-32 x 2-1/2"
1/4"-20 x 1/2"
1/4"-20 x 3/4"
1/4"-20 x 1"
1/4"-20 x 1-1/4"
1/4"-20 x 1-1/2"
1/4"-20 x 2"
Made to order
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
C
100 4000
0.20
C
100 4000
0.34
C
100 3000
0.45
C
100 3000
0.63
C
100 4000
0.23
C
100 4000
0.29
C
100 4000
0.40
C
100 4000
0.52
C
100 4000
0.30
C
100 4000
0.40
C
100 4000
0.53
C
100 3000
0.66
C
100 3000
0.94
C
100 1000
1.83
C
100 4000
0.42
C
100 4000
0.52
C
100 3000
0.66
C
100 3000
0.80
C
100 3000
0.94
C
100 1000
1.24
C
100 1000
1.50
C
100 4000
0.76
C
100 3000
1.01
C
100 3000
1.26
C
100 3000
1.51
C
100 1000
1.77
C
100 1000
2.27
Table continues on next page
81
Cat. No.
Size
880063
880065
880101
880103
880105
880106
1/4"-20 x 3-1/2"
1/4"-20 x 4"
#12-24 x 1/2"
#12-24 x 3/4"
#12-24 x 1"
#12-24 x 1-1/2"
Made to order
•
•
•
•
•
•
C
C
C
C
C
C
100
100
100
100
100
100
1000
500
400
4000
3000
3000
WT./UM
3.24
4.25
0.45
0.72
1.09
1.35
screw s
&
Bolts
Pan Phillips Head
Cat. No.
Size
883056
883057
883058
883060
883062
883064
883091
883093
883095
883096
883102
883104
883106
883108
883110
883112
883114
883116
883125
883126
883128
883130
883131
883132
883134
883136
883138
883139
883169
883174
#8-32 x 1/2"
#8-32 x 5/8"
#8-32 x 3/4"
#8-32 x 1"
#8-32 x 1-1/2"
#8-32 x 2"
#10-32 x 1/2"
#10-32 x 3/4"
#10-32 x 1"
#10-32 x 1-1/4"
#10-24 x 1/2"
#10-24 x 3/4"
#10-24 x 1"
#10-24 x 1-1/2"
#10-24 x 2"
#10-24 x 2-1/2"
#10-24 x 3"
#10-24 x 4"
1/4"-20 x 3/8
1/4"-20 x 1/2"
1/4"-20 x 3/4"
1/4"-20 x 1"
1/4"-20 x 1-1/4"
1/4"-20 x 1-1/2"
1/4"-20 x 2"
1/4"-20 x 2-1/2"
1/4"-20 x 3"
1/4"-20 x 4"
3/8"-16 x 3/4"
3/8"-16 x 1-3/4"
Made to order
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
4000
4000
4000
4000
3000
3000
4000
4000
3000
3000
4000
4000
3000
3000
3000
1000
1000
1000
4000
3000
3000
3000
3000
1000
1000
1000
1000
500
1000
1000
WT./UM
0.35
0.40
0.46
0.56
0.77
1.01
0.49
0.62
0.75
1.05
0.49
0.62
0.75
1.03
1.45
1.75
1.91
2.53
0.96
0.97
1.19
1.45
1.69
1.97
2.42
2.92
3.43
4.63
3.83
6.31
Cat. No.
Size
801430
801431
801432
801433
801434
801435
801436
801438
801440
801441
801442
801443
801444
801445
801446
801447
801483
801487
3/8"-x 1-1/4"
3/8" x 1-1/2"
3/8" x 2"
3/8" x 2-1/2"
3/8" x 3"
3/8" x 3-1/2"
3/8" x 4 "
3/8" x 5"
3/8" x 6"
1/2"-13 x 3/4"
1/2"-13 x 1"
1/2"-13 x 1-1/4"
1/2"-13 x 1-1/2"
1/2"-13 x 2"
1/2"-13 x 2-1/2"
1/2"-13 x 3"
5/8"-11 x 3"
5/8"-11 x 4"
Made to order
•
•
•
•
•
•
•
•
•
•
•
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
50
50
50
50
50
50
50
50
50
50
50
50
50
25
25
1000
1000
500
500
500
250
250
250
250
500
500
500
500
250
250
250
125
125
WT./UM
4.78
5.54
6.94
8.52
10.04
11.51
13.06
15.95
19.13
7.28
8.30
9.30
10.42
13.25
16.05
18.75
7.45
9.15
Stainless Steel Self Drilling Screws
Hex Washer Head
Cat. No.
Size
813502
813503
813504
813507
813509
813510
813512
813513
813515
813516
813517
813518
813522
813523
813524
813525
813526
813529
813530
813531
813532
813533
813534
813535
#6-20 x 1/2"
#6-20 x 3/4"
#6-20 x 1"
#8-18 x 1/2"
#8-18 x 3/4"S
#8-18 x 1"
#8-18 x 1-1/2"
#10-16 x 1/2"
#10-16 x 3/4"
#10-16 x 1"
#10-16 x 1-1/4"
#10-16 x 1-1/2"
#12-14 x 3/4"
#12-14 x 1"
#12-14 x 1-1/4"
#12-14 x 1-1/2"
#12-14 x 2"
#14-14 x 3/4"
#14-14 x 1"
#14-14 x 1-1/4"
#14-14 x 1-1/2"
#14-14 x 2"
#14-14 x 2-1/2"
#14-14 x 3"
Made to order
•
•
•
•
•
•
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
4000
4000
4000
4000
4000
3000
3000
4000
3000
3000
3000
3000
3000
3000
3000
3000
1000
3000
3000
1000
1000
1000
1000
1000
WT./UM
0.26
0.33
0.38
0.40
0.50
0.55
0.70
0.50
0.60
0.70
0.90
1.00
0.80
0.90
1.15
1.30
1.54
0.70
0.80
1.65
1.86
2.31
2.75
3.17
Stainless Steel Tap Bolts
82
Cat. No.
Size
801400
801401
801402
801403
801404
801405
801406
801407
801409
801415
801416
801418
801419
801420
801428
801429
1/4"-20 x 1/2"
1/4"-20 x 3/4"
1/4"-20 x 1"
1/4"-20 x 1-1/4"
1/4"-20 x 1-1/2"
1/4"-20 x 2"
1/4"-20 x 2-1/2"
1/4"-20 x 3"
1/4"-20 x 4"
5/16"-18 x 3/4"
5/16"-18 x 1"
5/16"-18 x 1-1/2"
5/16"-18 x 2"
5/16"-18 x 2-1/2"
3/8" x 3/4"
3/8" x 1"
Made to order
•
•
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
2000
2000
2000
1000
1000
1000
1000
1000
500
2000
1000
1000
1000
500
1000
1000
WT./UM
1.18
1.44
1.67
2.01
2.36
3.07
3.75
4.35
5.75
2.33
2.74
3.82
4.82
5.95
3.56
4.03
Stainless Steel Self Drilling Screws
Pan Phillips Head
Cat. No.
Size
813603
813604
813605
813607
813609
813610
813614
813615
#6-20 x 5/8"
#6-20 x 3/4"
#6-20 x 1"
#8-18 x 2"
#8-18 x 3/4"
#8-18 x 1 "
#10-16 x 1/2"
#10-16 x 3/4"
Made to order
•
•
•
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
4000
4000
4000
3000
4000
4000
4000
4000
WT./UM
0.20
0.25
0.30
0.90
0.40
0.50
0.50
0.60
Size
813616
813618
813619
813623
813627
813628
#10-16 x 1"
#10-16 x 1-1/2"
#10-16 x 2"
#12-14 x 1"
#12-14 x 2-1/2"
#12-14 x 3"
Made to order
•
•
C
C
C
C
C
C
100
100
100
100
100
100
3000
3000
1000
3000
1000
1000
WT./UM
0.70
1.00
1.10
1.00
2.10
2.30
3/16" x 1"
1/4" x 1"
1/4" x 1-1/4"
1/4" x 1-1/2"
5/16" x 1-1/2"
3/8" x 1-1/4"
3/8" x 1-1/2"
1/2" x 1-1/2"
1/2" x 2"
Made to order
•
•
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
2000
2000
2000
1000
1000
2000
1000
1000
1000
WT./UM
1.30
1.22
1.90
3.05
2.70
2.00
2.95
2.45
5.30
Stainless Steel Type 316 Fender Washers
Cat. No.
Size
846305
846309
846310
846312
1/4" x 1-1/4"
3/8" x 1-1/4"
3/8" x 1-1/2"
1/2" x 2"
Made to order
•
•
•
•
C
C
C
C
100
100
100
100
2000
2000
1000
1000
WT./UM
1.90
2.00
2.95
5.30
Size
849002
849003
849004
849005
849006
No. 6
No. 8
No. 10
No. 12
No. 14
Made to order
•
C
C
C
C
C
100
100
100
100
100
Size
842002
842003
842004
842006
842008
842009
842010
842011
842013
843002
843003
843004
843005
1/4"
5/16"
3/8"
1/2"
5/8"
3/4"
7/8"
1"
1-1/4"
No. 6
No. 8
No. 10
No. 12
Made to order
•
•
•
•
•
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
50
25
25
25
10
100
100
100
100
4000
4000
4000
2000
1000
500
500
500
100
4000
4000
4000
4000
WT./UM
0.60
1.10
1.40
3.90
7.70
11.00
15.30
18.80
26.00
0.10
0.20
0.20
0.30
Stainless Steel Flat Washers Type 316
Cat. No.
Size
843304
844002
844003
844004
844006
844008
844009
#10
1/4"
5/16"
3/8"
1/2"
5/8"
3/4"
Made to order
•
C
C
C
C
C
C
C
100
100
100
100
100
50
25
WT./UM
4000
4000
4000
4000
2000
1000
500
0.20
0.60
1.10
1.40
3.90
7.70
11.00
WT./UM
Stainless Steel Split Lock Washers
Stainless Steel Finishing Washers
Cat. No.
Cat. No.
BO LTS
Size
846002
846004
846005
846006
846008
846009
846010
846011
846012
Stainless Steel Flat Washers
&
Stainless Steel Fender Washers
Cat. No.
SCREW S
Cat. No.
4000
4000
4000
4000
3000
WT./UM
0.08
0.11
0.14
0.21
0.27
Cat. No.
Size
847002
847003
847004
847006
847007
847008
847010
847012
847013
847014
847015
No. 6
No. 8
No. 10
1/4"
5/16"
3/8"
1/2"
5/8"
3/4"
1"
7/8"
Made to order
•
•
•
•
•
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
50
50
4000
4000
4000
4000
4000
4000
2000
1000
1000
500
500
0.03
0.05
0.07
0.22
0.38
0.60
1.30
2.40
4.00
8.80
6.34
WT./UM
Stainless Steel Neoprene
Sealing Washers
Cat. No.
Size
813547
813548
813549
813550
813553
813554
#8
#10
#12
#14
3/8"
5/16"
Made to order
•
•
C
C
C
C
C
C
100
100
100
100
100
100
1000
1000
1000
1000
1000
1000
WT./UM
0.30
0.30
0.40
0.40
Stainless Steel Split Lock Washers
Type 316
Cat. No.
Size
847304
847306
#10
1/4"
Made to order
•
•
100
100
4000
4000
0.70
0.22
83
screw s
&
Bolts
Stainless Steel Machine Screw Nuts
Cat. No.
Size
815005
815006
815007
815008
815009
#6-32
#8-32
#10-24
#10-32
#12-24
Made to order
•
C
C
C
C
C
100
100
100
100
100
4000
4000
4000
4000
4000
WT./UM
0.21
0.28
0.33
0.33
0.56
Size
816001
816002
816003
816005
816007
816008
816009
816010
1/4"-20
5/16"-18
3/8"-16
1/2"-13
5/8"-11
3/4"-10
7/8"-9
1"-8
Made to order
•
•
C
C
C
C
C
C
C
C
100
100
100
50
50
25
10
10
Cat. No.
Size
833005
833006
833007
1/4"-20
5/16"-18
3/8"-16
Made to order
•
C
C
C
100
100
100
WT./UM
4000
2000
1000
2.30
2.05
3.70
WT./UM
Stainless Steel Rod Coupling Nuts
Stainless Steel Finish Hex Nuts NC
Cat. No.
Stainless Steel Wing Nuts Forged
4000
3000
2000
1000
500
250
200
100
WT./UM
0.68
1.02
1.49
3.60
7.11
11.80
17.67
26.60
Cat. No.
Size
830005
830007
830009
830010
1/4"-20
3/8"-16
1/2"-13
5/8"-11
Made to order
C
C
C
C
100
100
50
25
2000
1000
500
250
1.90
3.60
8.24
30.87
Stainless Steel Serrated Flange Nuts
Stainless Steel Finished Hex Nuts
NC Type 316
Cat. No.
Size
819001
819002
819003
819005
819007
819008
1/4"-20
5/6"-18
3/8"-16
1/2"-13
5/8"-11
3/4"-10
Made to order
•
•
•
•
C
C
C
C
C
C
100
100
100
50
50
25
4000
3000
2000
1000
500
250
WT./UM
0.68
1.02
1.49
3.60
7.11
11.80
Stainless Steel Locknuts Nylon Insert
Cat. No.
Size
828003
828004
828005
828006
828007
828008
828010
#8-32 NM
#10-24 NM
#10-32 NM
1/4"-20 NE
5/16"-18 NE
3/8"-16 NE
1/2"-13 NE
Made to order
•
•
•
•
C
C
C
C
C
C
C
100
100
100
100
100
100
50
WT./UM
4000
4000
4000
4000
3000
200
500
0.41
0.48
0.48
0.84
1.10
1.76
4.10
WT./UM
Stainless Steel Acorn Nuts
84
Cat. No.
Size
832005
832007
1/4"-20
3/8"-16
Made to order
•
C
C
100
100
4000
4000
0.92
2.34
Cat. No.
Size
816498
816500
1/4"-20
3/8"-16
Made to order
C
C
100
100
WT./UM
4000
2000
0.80
1.90
WT./UM
domestic Products
Zinc Cap Screw Grade 5 USA
Cat. No.
Size
D002001
D002003
D002005
D002006
D002007
D002009
D002011
D002013
D002015
D002017
D002022
D002024
D002026
D002027
D002028
D002030
D002032
D002034
D002036
D002038
D002045
D002047
D002048
D002049
D002051
D002053
1/4"-20 x 1/2"
1/4"-20 x 3/4"
1/4"-20 x 1"
1/4"-20 x 1-1/4"
1/4"-20 x 1-1/2"
1/4"-20 x 2"
1/4"-20 x 2-1/2"
1/4"-20 x 3"
1/4"-20 x 3-1/2"
1/4"-20 x 4"
5/16"-18 x 1/2"
5/16"-18 x 3/4"
5/16"-18 x 1"
5/16"-18 x 1-1/4"
5/16"-18 x 1-1/2"
5/16"-18 x 2"
5/16"-18 x 2-1/2"
5/16"-18 x 3"
5/16"-18 x 3-1/2"
5/16"-18 x 4"
3/8"-16 x 3/4"
3/8"-16 x 1"
3/8"-16 x 1-1/4"
3/8"-16 x 1-1/2"
3/8"-16 x 2"
3/8"-16 x 2-1/2"
Made to order
•
•
•
•
•
•
•
•
•
•
•
•
•
•
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
50
50
100
100
100
100
100
50
2000
2000
2000
1000
1000
1000
1000
1000
500
500
2000
2000
1000
1000
1000
1000
500
500
500
500
1000
1000
1000
1000
500
500
1.14
1.41
1.67
2.01
2.36
3.07
3.75
4.35
5.25
5.75
2.00
2.33
2.74
3.23
3.82
4.82
6.10
6.91
4.25
4.75
3.40
4.03
4.78
5.64
6.94
8.52
domestic products
Made to order
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
50
50
50
50
50
50
50
50
50
50
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
20
500
250
250
500
500
500
500
250
250
250
125
125
125
250
250
250
125
125
125
125
125
125
125
125
125
125
125
125
125
125
75
75
75
75
75
60
WT./UM
10.04
11.52
13.06
7.26
8.30
9.30
10.42
13.26
16.06
19.87
21.55
24.12
6.95
16.12
18.00
19.77
22.12
24.20
26.32
28.12
30.52
32.40
34.60
37.12
38.92
28.70
31.30
34.40
36.60
40.30
46.00
48.90
52.40
55.00
64.50
76.90
Zinc USS Flat Washers USA
Cat. No.
Size
D042002
D042003
D042004
D042006
D042008
D042009
D042010
D042011
1/4"
5/16"
3/8"
1/2"
5/8"
3/4"
7/8"
1"
Made to order
•
•
C
C
C
C
C
C
C
C
100
100
100
100
50
25
25
25
WT./UM
4000
3000
2000
1000
500
250
250
250
0.70
1.10
1.50
3.90
7.70
11.00
15.30
18.80
WT./UM
BO LTS
3/8"-16 x 3"
3/8"-16 x 3-1/2"
3/8"-16 x 4"
1/2"-13 x 3/4"
1/2"-13 x 1"
1/2"-13 x 1-1/4"
1/2"-13 x 1-1/2"
1/2"-13 x 2"
1/2"-13 x 2-1/2"
1/2"-13 x 3"
1/2"-13 x 3-1/2"
1/2"-13 x 4"
1/2"-13 x 4-1/2"
5/8"-11 x 1-1/4"
5/8"-11 x 1-1/2"
5/8"-11 x 1-3/4"
5/8"-11 x 2"
5/8"-11 x 2-1/4""
5/8"-11 x 2-1/2"
5/8"-11 x 2-3/4"
5/8"-11 x 3"
5/8"-11 x 3-1/4
5/8"-11 x 3-1/2"
5/8"-11 x 4"
5/8"-11 x 5-1/2"
3/4"-10 x 1-1/2"
3/4"-10 x 1-3/4"
3/4"-10 x 2"
3/4"-10 x 2-1/4""
3/4"-10 x 2-1/2"
3/4"-10 x 3"
3/4"-10 x 3-1/4
3/4"-10 x 3-1/2"
3/4"-10 x 3-3/4"
3/4"-10 x 4-1/2"
3/4"-10 x 5-1/2"
&
Size
D002055
D002057
D002059
D002083
D002085
D002086
D002087
D002089
D002091
D002093
D002095
D002097
D002098
D002119
D002120
D002121
D002122
D002123
D002124
D002125
D002126
D002127
D002128
D002130
D002133
D002141
D002142
D002143
D002144
D002145
D002147
D002148
D002149
D002150
D002152
D002154
SCREW S
Cat. No.
Zinc Heavy Hex Nuts Grade 2 USA
Cat. No.
Size
DB21003
DB21005
DB21006
DB21007
3/8"-16
1/2"-13
5/8"-11
3/4"-10
Made to order
C
C
C
C
100
50
25
25
1000
500
250
250
3.00
3.15
2.90
4.65
WT./UM
Zinc Rod Coupling Nuts USA
Cat. No.
Size
D030007
D030009
3/8"-16 x 1/2"x 1-1/8"
1/2"-13 x 5/8" x 1-1/4"
Made to order
C
C
100
50
1000
500
3.85
3.05
WT./UM
Zinc Split Lock Washers usa
Cat. No.
Size
D047006
D047007
D047008
D047010
D047012
D047013
D047014
D047015
1/4"
5/16"
3/8"
1/2"
5/8"
3/4"
7/8"
1"
Made to order
•
•
•
•
C
C
C
C
C
C
C
C
100
100
100
100
100
100
50
50
4000
4000
4000
3000
1000
1000
500
500
WT./UM
0.22
0.38
0.60
1.30
2.40
4.00
6.34
8.80
Zinc Fender Washers USA
Cat. No.
Size
D046004
D046005
D046006
D046007
D046009
D046010
D046012
1/4" x 1"
1/4" x 1-1/4"
1/4" x 1-1/2"
5/16" x 1-1/4"
3/8" x 1-1/4"
3/8" x 1-1/2"
1/2" x 2"
Made to order
•
C
C
C
C
C
C
C
WT./UM
100
100
100
2000
2000
1000
1.22
1.90
3.05
100
100
100
2000
1000
1000
2.00
2.95
5.30
Zinc Hex Nuts NC Grade 5 USA
Cat. No.
Size
D023001
D023002
D023003
D023005
D023006
D023007
D023008
D023009
1/4"-20
5/16"-18
3/8"-16
1/2"-13
5/8"-11
3/4"-10
7/8"-9
1"-8
Made to order
•
•
C
C
C
C
C
C
C
C
100
100
100
50
50
25
10
10
4000
3000
2000
1000
500
250
200
100
0.68
1.02
1.49
3.60
7.11
11.80
17.54
26.40
WT./UM
Zinc Heavy Hex Nuts Grade 2 USA
Cat. No.
Size
D021003
D021005
D021006
D021007
D021008
D021009
3/8"-16
1/2"-13
5/8"-11
3/4"-10
7/8"-9
1"-8
Made to order
•
•
•
C
C
C
C
C
C
100
100
100
50
50
10
4000
3000
2000
1000
500
100
0.68
1.02
1.49
3.60
7.11
4.01
85
Bolts
Jar Products
Brass Finishing Washers
Drywall Screws Phillips Bugle Head
Phosphate Finish Fine Thread
screw s
Brass Products
&
brass products • jar products
Cat. No.
Size
749003
749004
749005
#8
#10
#12
Made to order
C
C
C
100
100
100
4000
4000
4000
WT./UM
0.11
0.14
0.27
Cat. No.
Size
005001J
005003J
005004J
005005J
005006J
005007J
005008J
#6 x 1"
#6 x 1-1/4"
#6 x 1-5/8"
#6 x 2"
#6 x 2-1/4""
#8 x 2-1/2"
#8 x 3"
Made to order
100
100
100
100
100
100
100
3000
3000
3000
1000
1000
1000
1000
WT./UM
0.35
0.45
0.50
0.60
0.65
1.05
1.15
Brass Wood Screws Flat Phillips Head
Cat. No.
Size
776025
776027
776029
776030
776050
776051
776052
776054
776056
776072
776074
776076
776078
776080
776085
776087
776088
776089
#6 x 1/2"
#6 x 3/4"
#6 x 1"
#6 x 1-1/4"
#8 x 1 "
#8 x 1-1/4"
#8 x 1-1/2"
#8 x 2"
#8 x 2-1/2"
#10 x 1"
#10 x 1-1/2"
#10 x 2"
#10 x 2-1/2"
#10 x 3"
#12 x 1"
#12 x 1-1/2"
#12 x 2"
#12 x 2-1/2"
Made to order
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
4000
4000
4000
4000
4000
4000
3000
3000
1000
4000
3000
1000
1000
1000
3000
1000
1000
3000
WT./UM
0.20
0.25
0.30
0.40
0.60
0.80
0.90
1.40
1.60
0.90
1.30
1.30
1.90
2.10
0.90
1.90
1.80
0.90
Drywall Screws Phillips Bugle Head
Phosphate Finish Coarse Thread
Cat. No.
Size
005051J
005053J
005054J
005055J
005058J
#6 x 1"
#6 x 1-1/4"
#6 x 1-5/8"
#6 x 2"
#8 x 3"
Made to order
C
C
C
C
C
100
100
100
100
100
WT./UM
3000
3000
3000
1000
1000
0.35
0.44
0.50
0.60
1.01
WT./UM
Framing Screws Pan Phillips Head
Cat. No.
Size
005185J
005186J
005187J
005189J
005190J
#6 x 7/16" Sharp Point
#6 x 7/16" M
#6 x 7/16" SD
#6 x 7/16" SDM
#6 x 7/16" SDM
Made to order
C
C
C
C
C
100 3000
1000 10000
100 3000
1000 10000
1000 10000
0.30
2.55
0.35
2.70
0.35
WT./UM
Zinc Fender Washers
86
Cat. No.
Size
046002J
046003J
046004J
046005J
046006J
046007J
046008J
046009J
046010J
046011J
046012J
046013J
046014J
046015J
3/16" x 1"
3/16" x 1-1/4"
1/4" x 1"
1/4" x 1-1/4"
1/4" x 1-1/2"
5/16" x 1-1/4"
5/16" x 1-1/2"
3/8" x 1-1/4"
3/8" x 1-1/2"
1/2" x 1-1/2"
1/2" x 2"
3/8"x 2"
1/4"x 2"
3/8" x 1"
Made to order
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
3000
2000
3000
2000
1000
2000
1000
2000
1000
1000
1000
1000
1000
3000
1.30
2.15
1.22
1.90
3.05
2.15
2.70
2.00
2.95
2.45
5.30
5.70
4.95
1.90
Jar Products
1/4"-20
5/16"-18
3/8"-16
1/2"-13
Made to order
C
C
C
C
100
100
100
50
3000
3000
2000
1000
WT./UM
0.75
1.10
1.55
1.85
Made to order
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
50
50
WT./UM
2000
1000
1000
1000
600
1000
1000
1000
1000
1000
600
500
300
1.85
2.05
2.60
3.10
3.70
2.85
3.35
4.25
4.65
5.10
6.60
4.50
BO LTS
Size
016001J
016002J
016003J
016005J
1/4"-20 x 1-1/4"
1/4"-20 x 1-1/2"
1/4"-20 x 2"
1/4"-20 x 2-1/2"
1/4"-20 x 3"
3/8"-16 x 1/2"
3/8"-16 x 3/4"
3/8"-16 x 1"
3/8"-16 x 1-1/4"
3/8"-16 x 1-1/2"
3/8"-16 x 2"
3/8"-16 X 2-1/2"
3/8"-16 x 3"
&
Cat. No.
Size
082206J
082207J
082209J
082211J
082213J
082245J
082247J
082249J
082250J
082251J
082253J
082255J
082257J
SCREW S
Zinc Hex Nuts
Cat. No.
Truss Combo Machine Screw
Cat. No.
Size
085005J
085007J
085009J
085010J
085011J
085013J
#6-32 x 1/2"
#6-32 x 3/4"
#6-32 x 1"
#6-32 x 1-1/4"
#6-32 x 1-1/2"
#6-32 x 2"
Made to order
C
C
C
C
C
C
100
100
100
100
100
100
WT./UM
3000
3000
3000
3000
3000
2000
0.30
0.40
0.50
0.76
0.60
0.75
WT./UM
Zinc Machine Screws
Round Combo Head (Slot/Phillips)
Cat. No.
Size
082005J
082007J
082009J
082010J
082011J
082013J
082015J
082017J
082019J
082027J
082028J
082030J
082032J
082033J
082034J
082036J
082037J
082038J
082039J
082053J
082055J
082057J
082058J
082059J
082061J
082063J
082065J
082083J
082084J
082086J
082088J
082089J
082090J
082092J
082200J
082201J
082203J
082205J
#6-32 x 1/2"
#6-32 x 3/4"
#6-32 x 1"
#6-32 x 1-1/4"
#6-32 x 1-1/2"
#6-32 x 2"
#6-32 x 2-1/2"
#6-32 x 3"
#6-32 X 4"
#8-32 x 3/8"
#8-32 x 1/2"
#8-32 x 3/4"
#8-32 x 1"
#8-32 x 1-1/4"
#8-32 x 1-1/2"
#8-32 x 2"
#8-32 x 2-1/2"
#8-32 x 3"
#8-32 X 4"
#10-24 x 1/2"
#10-24 x 3/4"
#10-24 x 1"
#10-24 x 1-1/4"
#10-24 x 1-1/2"
#10-24 x 2"
#10-24 x 2-1/2"
#10-24 x 3"
#10-32 x 3/8"
#10-32 x 1/2"
#10-32 x 3/4"
#10-32 x 1"
#10-32 x 1-1/4"
#10-32 x 1-1/2"
#10-32 x 2"
1/4"-20 x 3/8"
1/4"-20 x 1/2"
1/4"-20 x 3/4"
1/4"-20 x 1"
Made to order
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
3000
3000
3000
3000
3000
2000
2000
1000
1000
3000
3000
3000
3000
3000
3000
1000
1000
1000
1000
3000
3000
3000
2000
2000
1000
1000
1000
3000
3000
3000
3000
2000
2000
1000
3000
3000
2000
2000
0.30
0.35
0.45
0.50
0.55
0.75
0.85
1.05
0.30
0.40
0.50
0.65
0.70
0.85
1.10
1.30
1.55
0.55
0.60
0.85
0.95
1.15
1.41
0.50
0.55
0.70
0.85
1.00
1.15
1.55
0.90
1.05
1.25
1.55
Zinc Machine Screws Flat Phillips Head
Cat. No.
Size
080003J
080004J
080006J
080008J
080009J
080010J
080012J
080016J
080018J
080020J
080021J
080022J
080024J
080025J
080026J
080027J
080028J
080030J
080032J
080033J
080034J
080036J
080037J
080038J
080040J
080042J
080044J
080045J
080046J
080050J
080051J
080052J
080053J
080055J
080056J
080057J
080059J
080060J
080062J
080200J
080300J
#6-32 x 3/8"
#6-32 x 1/2"
#6-32 x 3/4"
#6-32 x 1"
#6-32 x 1-1/4"
#6-32 x 1-1/2"
#6-32 x 2"
#8-32 x 1/2"
#8-32 x 3/4"
#8-32 x 1"
#8-32 x 1-1/4"
#8-32 x 1-1/2"
#8-32 x 2"
#8-32 x 2-1/2"
#8-32 x 3"
#10-24 x 3/8"
#10-24 x 1/2"
#10-24 x 3/4"
#10-24 x 1"
#10-24 x 1-1/4"
#10-24 x 1-1/2"
#10-24 x 2 "
#10-24 x 2-1/2"
#10-24 x 3"
#10-32 x 1/2"
#10-32 x 3/4"
#10-32 x 1"
#10-32 x 1-1/4"
#10-32 x 1-1/2"
#1/4-20 x 3/8"
#1/4-20 x 1/2"
#1/4-20 x 5/8"
#1/4-20 x 3/4"
#1/4-20 x 1"
#1/4-20 x 1-1/4"
#1/4-20 x 1-1/2"
#1/4-20 x 2"
#1/4-20 x 21/2"
#1/4-20 x 3"
#6-32 x 2-1/2"
#6-32 x 3"
Made to order
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
3000
3000
3000
3000
3000
3000
2000
3000
3000
3000
3000
3000
2000
1000
1000
3000
3000
3000
3000
2000
2000
1000
1000
1000
3000
3000
3000
2000
2000
3000
3000
2000
2000
2000
1000
1000
1000
1000
600
2000
1000
WT./UM
0.30
0.40
0.20
0.55
0.45
0.50
0.40
0.40
0.55
0.60
0.70
1.10
1.45
0.95
0.75
87
screw s
&
Bolts
jar products
Zinc Self Drilling Screws Hex Head
Zinc Machine Screws Flat Slotted Head
Cat. No.
Size
078038J
078040J
078042J
078043J
078044J
078046J
078048J
078049J
078050J
#6-32 x 1/2"
#6-32 x 3/4"
#6-32 x 1
#6-32 x 1-1/4"
#6-32 x 1-1/2"
#6-32 x 2"
#6-32 x 2-1/2"
#6-32 x 3
#6-32 x 4"
Made to order
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
3000
3000
3000
3000
3000
2000
2000
1000
1000
WT./UM
0.25
0.30
0.40
0.45
0.55
0.70
0.80
1.00
1.25
Cat. No.
Size
135011J
135031J
135034J
135507J
135509J
135515J
#8-18 x 1-1/4" #2
#14-14 x 1-1/4" #3
#14-14 x 2-1/2" #3
#8-18 x 1/2" #2
#8-18 x 3/4" #2
#10-16 x 3/4" #3
Made to order
•
•
C
C
C
C
C
C
100 3000
100 3000
100 1000
1000 10000
1000 10000
500 5000
WT./UM
0.75
1.70
2.91
3.35
3.97
3.04
Zinc Self Drilling Screws Pan Phillips
Zinc Tap Bolts A307
Cat. No.
Size
001400J
001401J
001402J
001403J
001404J
001405J
001406J
001407J
001415J
001416J
001417J
001418J
001419J
001420J
001421J
001427J
001428J
001429J
001430J
001431J
001432J
001433J
001434J
1/4"-20 x 1/2"
1/4"-20 x 3/4"
1/4"-20 x 1"
1/4"-20 x 1-1/4"
1/4"-20 x 1-1/2"
1/4"-20 x 2"
1/4"-20 x 2-1/2"
1/4"-20 x 3"
5/16"-18 x 3/4"
5/16"-18 x 1"
5/16"-18 x 1-1/4"
5/16"-18 x 1-1/2"
5/16"-18 x 2"
5/16"-18 x 2-1/2"
5/16"-18 x 3
3/8"-16 x 1/2"
3/8"-16 x 3/4"
3/8"-16 x 1"
3/8"-16 x 1-1/4"
3/8"-16 x 1-1/2"
3/8"-16 x 2"
3/8"-16 x 2-1/2"
3/8"-16 x 3"
Made to order
•
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
50
50
50
3000
2000
2000
1000
1000
1000
1000
600
2000
1000
1000
1000
600
600
600
1000
1000
1000
1000
600
500
300
300
WT./UM
1.20
1.45
1.80
2.00
2.30
2.80
3.15
3.90
2.40
2.90
3.35
3.70
4.60
5.10
6.35
3.65
4.30
4.85
5.40
6.70
4.00
4.65
4.65
Size
015005J
015006J
015007J
015008J
015009J
#6-32
#8-32
#10-24
#10-32
#12-24
Made to order
Size
136001J
136002J
136004J
136005J
136008J
136009J
136010J
136011J
136012J
136014J
136015J
136016J
136017J
136018J
136022J
136023J
#6-20 x 3/8" #2
#6-20 x 1/2" #2
#6-20 x 3/4" #2
#6-20 x 1" #2
#8-18 x 1/2" #2
#8-18 x 3/4" #2
#8-18 x 1" #2
#8-18 x 1-1/4" #2
#8-18 x 1-1/2" #2
#10-16 x 1/2"#3
#10-16 x 3/4"#3
#10-16 x 1" #3
#10-16 x 1-1/4" #3
#10-16 x 1-1/2" #3
#12-14 x 3/4"#3
#12-14 x 1" #3
Made to order
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
WT./UM
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
0.25
0.30
0.35
0.40
0.35
0.45
0.55
0.65
0.75
0.50
0.60
0.75
0.85
1.05
0.80
1.00
WT./UM
Zinc S Hook
Cat. No.
Size
000520J
000521J
000522J
1"
1-1/4"
1-1/2"
Made to order
C
C
C
100
100
100
3000
2000
1000
0.80
0.77
1.30
WT./UM
Drywall Screws Coarse Thread
Zinc Machine Screw Nuts
Cat. No.
Cat. No.
C
C
C
C
C
100
100
100
100
100
3000
3000
3000
3000
3000
WT./UM
0.25
0.35
0.35
0.35
0.60
Cat. No.
Size
005551J
005062J
005063J
005064J
005067J
#6 x 1"
#6 x 1-1/4"
#6 x 1-5/8
#6 x 2"
#8 x 3"
Made to order
C
C
C
C
C
100
100
100
100
100
3000
3000
3000
2000
1000
0.15
0.20
0.60
0.60
0.08
Drywall Screws Yellow Zinc Coarse Thread
88
Cat. No.
Size
005562J
005563J
005564J
#6 x 1-1/4"
#6 x 1-5/8
#6 x 2"
Made to order
C
C
C
500
500
300
5000
3000
1800
WT./UM
1.70
2.20
1.65
Jar Products
Size
062124J
062125J
062127J
#10 x 3/4" AB Pan Sqr
#10 x 1" A Pan Sqr
#10 x 1-1/2" A Pan Sqr
Made to order
C
C
C
100
100
100
3000
3000
2000
WT./UM
0.60
0.75
1.10
Cat. No.
Size
061103J
061105J
061106J
061107J
061108J
061109J
061111J
061113J
061114J
061115J
061116J
061118J
061122J
061124J
061125J
061126J
061127J
061129J
061130J
061131J
061134J
061135J
061136J
061137J
061139J
061140J
061141J
061144J
061145J
061146J
061148J
061149J
061150J
#6 x 1/2" AB
#6 x 3/4" AB
#6 x 1" A
#6 x 1-1/4" A
#6 x 1/1/2"
#6 x 2" A
#8 x 1/2" AB
#8 x 3/4" AB
#8 x 1" A
#8 x 1-1/4" A
#8 x 1-1/2" A
#8 x 2" A
#10 x 1/2" AB
#10 x 3/4" AB
#10 x 1" A
#10 x 1-1/4" A
#10 x 1-1/2" A
#10 x 2" A
#10 x 2-1/2" A
#10 x 3" A
#12 x 3/4" AB
#12 x 1" A
#12 x 1-1/4" A
#12 x 1-1/2" A
#12 x 2" A
#12 x 2-1/2" A
#12 x 3" A
#14 x 1" A
#14 x 1-1/4" A
#14 x 1-1/2" A
#14 x 2" A
#14 x 2-1/2" A
#14 x 3" A
Made to order
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
•
•
•
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
Zinc Tap Screws Hex Head No Slot
Cat. No.
Size
060126J
#10 x 1"
Made to order
u/m box qty.
C
100
3000
3000
3000
3000
3000
2000
3000
3000
3000
3000
2000
1000
3000
3000
3000
2000
2000
1000
1000
1000
3000
3000
2000
2000
1000
1000
1000
2000
2000
1000
1000
1000
600
WT./UM
0.25
0.35
0.40
0.45
0.55
0.65
0.40
0.45
0.55
0.65
0.80
1.00
0.55
0.65
0.75
0.85
1.00
1.25
1.55
1.80
0.85
1.00
1.20
1.35
1.80
1.95
2.40
0
0
0
0
0
0
Ctn. Qty.
WT./UM
2000
0.765
Size
060008J
060009J
060013J
060015J
060016J
060017J
060018J
060019J
060023J
060025J
060026J
060027J
060028J
060029J
060031J
060033J
060034J
060035J
060036J
060037J
060038J
060039J
060040J
060041J
060043J
060044J
060045J
060046J
#6 x 1/2" AB
#6 x 3/4" AB
#8 x 1/2" AB #8 x 3/4" AB #8 x 1" A #8 x 1-1/4" A #8 x 1-1/2" A #8 x 2" A #10 x 1/2" AB #10 x 3/4" AB #10 x 1" A #10 x 1-1/4" A
#10 x 1-1/2" A #10 x 2" A #10 x 3" A #12 x 3/4" AB #12 x 1" A #12 x 1-1/4" A #12 x 1-1/2" A #12 x 2" A #12 x 2-1/2" AB
#12 x 3" A #14 x 3/4" AB #14 x 1" A #14 x 1-1/2" A #14 x 2" A #14 x 2-1/2" A
#14 x 3" A Made to order
•
•
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
3000
3000
3000
3000
3000
3000
3000
1000
3000
3000
3000
2000
2000
1000
600
2000
2000
2000
2000
1000
1000
1000
2000
2000
1000
1000
1000
600
WT./UM
0.25
0.35
0.40
0.45
0.55
0.65
0.75
1.00
0.50
0.65
0.75
0.95
1.00
1.30
1.90
0.95
0.98
1.15
1.35
1.70
1.75
2.35
1.30
1.45
1.95
2.40
BO LTS
Zinc Tap Screws Pan Combo Head
Cat. No.
&
Cat. No.
SCREW S
Zinc Tap Screws Hex Slot Head
Zinc Tap Screws Square
3.40
Zinc Tap Screws Zip Point Hex Head
Cat. No.
Size
061017J
061031J
061032J
061033J
061034J
061035J
061036J
061037J
061038J
061043J
061045J
061065J
#7 x 1/2"
#8 x 1/2"
#8 x 1/2" M
#8 x 3/4"
#8 x 3/4" M
#8 x 1"
#8 x 1" M
#8 x 1-1/4"
#8 x 1-1/2"
#10 x 1/2"
#10 x 3/4"
#10 x 1"
Made to order
C
C
C
C
C
C
C
C
C
C
C
C
100 3000
100 3000
1000 10000
100 3000
1000 10000
100 3000
1000 10000
100 3000
100 3000
100 3000
100 3000
100 3000
WT./UM
0.31
0.31
0.31
0.42
0.42
0.51
0.51
0.62
0.66
0.62
0.66
Green Grounding Screws and Clips
Cat. No.
Size
079101J #10-32 x 3/8" Type F Hex Head
079100J #10-32 x 3/8" Hex Combo Head
079102J Grounding Clips
Made to order
C
C
C
100
100
100
3000
3000
3000
WT./UM
0.55
0.55
0.41
89
screw s
&
Bolts
Jar products
Plate Screws Oval Head
Cat. No.
Size
079200J
079205J
079300J
079305J
#6-32 x 1/2" White
#6-32 x 1" White
#6-32 x 1/2" Ivory
#6-32 x 1" Ivory
Made to order
C
C
C
C
100
100
100
100
3000
3000
3000
3000
WT./UM
0.24
0.39
0.24
0.39
Zinc Self Drilling Screws Wafer Head/100 Jar
Cat. No.
Size
138525J
138527J
138529J
138530J
138531J
138533J
138535J
138537J
#8 x 1/2"
#8 x 3/4"
#8 x 1"
#8 x 1-1/4"
#8 x 1-5/8"
#8 x 2"
#8 x 2-1/2"
#8 x 3"
Made to order
•
•
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
3000
3000
3000
3000
2000
1000
1000
1000
WT./UM
0.36
0.45
0.55
0.64
0.78
0.94
1.15
1.36
Zinc Self Drilling Screws
Pan Phillips Head
Cat. No.
Size
136002J
136004J
136005J
136008J
136009J
136010J
136011J
136012J
136014J
136015J
136016J
136017J
136018J
136022J
136023J
#6-20 x 1/2" #2
#6-20 x 3/4" #2
#6-20 x 1" #2
#8-18 x 1/2" #2
#8-18 x 3/4" #2
#8-18 x 1" #2
#8-18 x 1-1/4" #2
#8-18 x 1-1/2" #2
#10-16 x 1/2" #3
#10-16 x 3/4" #3
#10-16 x 1" #3
#10-16 x 1-1/4" #3
#10-16 x 1-1/2" #3
#12-14 x 3/4" #3
#12-14 x 1" #3
Made to order
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
WT./UM
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
2000
3000
3000
0.30
0.35
0.40
0.35
0.45
0.55
0.65
0.75
0.50
0.60
0.75
0.85
1.05
0.80
1.00
WT./UM
Zinc Self Drilling Screws Wafer Head/1000 Jar Zinc Self Drilling Screws Hex Head
Cat. No.
Size
138625J
138627J
138629J
138630J
138631J
138633J
138635J
138637J
#8 x 1/2"
#8 x 3/4"
#8 x 1"
#8 x 1-1/4"
#8 x 1-5/8"
#8 x 2"
#8 x 2-1/2"
#8 x 3"
Made to order
•
•
C
C
C
C
C
C
C
C
1000 10000
1000 6000
1000 6000
1000 6000
500 3000
500 3000
500 3000
250 1500
WT./UM
0.36
0.45
0.55
0.64
0.78
0.94
1.15
3.35
Zinc Zip Point Screws Wafer Head/100 Jar
Cat. No.
Size
138125J
138127J
138129J
138130J
138131J
138133J
138135J
138137J
#8 x 1/2"
#8 x 3/4"
#8 x 1"
#8 x 1-1/4"
#8 x 1-1/2"
#8 x 2"
#8 x 2-1/2"
#8 x 3"
Made to order
•
•
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
3000
3000
3000
3000
2000
1000
1000
1000
WT./UM
0.34
0.43
0.53
0.62
0.73
0.92
1.25
1.40
Zinc Zip Point Screws Wafer Head/500 Jar
90
Cat. No.
Size
138225J
138227J
138229J
138230J
138231J
138235J
138237J
#8 x 1/2"
#8 x 3/4"
#8 x 1"
#8 x 1-1/4"
#8 x 1-1/2"
#8 x 2-1/2"
#8 x 3"
Made to order
•
•
C
C
C
C
C
C
C
1000 10000
1000 6000
1000 6000
500 5000
500 3000
500 3000
500 3000
WT./UM
3.62
3.90
2.41
3.40
3.70
4.00
4.20
Cat. No.
Size
135007J
135009J
135010J
135012J
135013J
135015J
135016J
135017J
135018J
135019J
135022J
135023J
135024J
135025J
135026J
135027J
135029J
135030J
135032J
135033J
135036J
135011J
135031J
135034J
#8-18 x 1/2" #2
#8-18 x 3/4" #2
#8-18 x 1" #2
#8-18 x 1-1/2" #2
#10-16 x 1/2" #2
#10-16 x 3/4" #3
#10-16 x 1" #3
#10-16 x 1-1/4" #3
#10-16 x 1-1/2" #3
#10-16 x 2" #3
#12-14 x 3/4" #3
#12-14 x 1" #3
#12-14 x 1-1/4" #3
#12-14 x 1-1/2" #3
#12-14 x 2" #3
#12-14 x 2-1/2" #3
#14-14 x 3/4" #3
#14-14 x 1" #3
#14-14 x 1-1/2" #3
#14-14 x 2" #3
#14-14 x 3" #3
#8-18 x 1-1/4" #2
#14-14 x 1-1/4" #3
#14-14 x 2-1/2" #3
Made to order
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
1000 10000
100 3000
100 3000
100 3000
100 3000
100 3000
100 3000
100 2000
100 2000
100 1000
100 3000
100 2000
100 2000
100 2000
100 1000
100 1000
100 3000
100 2000
100 1000
100 1000
100
600
100 3000
100 1000
100
600
0.40
0.50
0.55
0.75
0.50
0.70
0.75
0.90
1.00
1.30
0.80
1.00
1.15
1.35
1.70
2.05
1.25
1.45
1.90
2.40
3.35
0.68
1.75
2.90
Jar Products
Jack Chain
Zinc Flat Washers SAE
043002J
043003J
043004J
043005J
043006J
043008J
043010J
043012J
No. 6
No. 8
No. 10
No. 12
1/4 "
3/8"
1/2"
5/8"
Made to order
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
50
WT./UM
3000
3000
3000
3000
3000
3000
2000
1000
0.20
0.20
0.20
0.30
0.45
0.85
2.10
1.30
WT./UM
Zinc Split Lock Washers
Cat. No.
Size
047002J
047003J
047004J
047005J
047006J
047007J
047008J
047010J
047012J
047013J
047014J
047015J
No. 6
No. 8
No. 10
No. 12
1/4"
5/16"
3/8"
1/2"
5/8"
3/4"
7/8"
1"
Made to order
•
•
•
C
C
C
C
C
C
C
C
C
C
C
C
100
100
100
100
100
100
100
100
100
100
25
25
3000
3000
3000
3000
3000
3000
3000
2000
1000
1000
250
250
0.10
0.10
0.15
0.15
0.30
0.40
0.70
1.35
2.50
4.05
1.60
2.26
WT./UM
Zinc Flat Washers uss
Cat. No.
Size
042001J
042002J
042003J
042004J
042006J
3/16"
1/4"
5/16"
3/8"
1/2"
Made to order
100
100
100
100
100
3000
3000
2000
2000
1000
0.30
0.70
1.25
1.50
3.90
Cat. No.
Size
000501
000505
000510
000515
#12 100' Reel
#10 100' Box
#16 100' Box
#14 Double Loop 200' Reel
Made to order
E
E
E
E
1
1
1
WT./UM
0
0
0
8.70
14.70
3.00
WT./UM
BO LTS
Size
&
Cat. No.
SCREW S
Accessories
Rebar Tie Wire
Cat. No.
Size
000985
16 Gauge Plain
Made to order
E
1
0
8.50
WT./UM
Screw Hook
Cat. No.
Size
010476
010472
W806
W802
Made to order
•
•
E
E
1
50
0
500
8.50
5.00
WT./UM
1
1
1
1
0.20
0.20
0.20
0.20
Magnetic Chucks (2-18")
Cat. No.
Size
221002
221005
221008
221010
1/4" Medium
5/16" Medium
3/8" Medium
2-7/8" Magnetic Bit Tip Holder
Made to order
0
0
0
0
Bit Tips, Holder and Handle
Cat. No.
Size
221021
221022
221023
221024
221025
221026
221035
221055
221066
221067
221199
221103
221104
221105
221106
221107
#1 Phillips Bit Tip
#2 x 1" Phillips Bit Tip
#3 Phillips Tip Bit
#1 x 1-15/16"
#2 x 1-15/16" Phillips Bit Tip
#3 x 1-15/16"
#8-10 x 1" Slot Insert
#1 x 2" Square Drive Hex Bit
#1 x 1"Square Drive Hex Bit
#2 x 1" Square Drive Hex Bit
1/4" Magnetic Storage Handle
#6 Spanner
#8 Spanner
#10 Spanner
#12 Spanner
#14 Spanner
Made to order
•
•
•
•
u/m box qty.
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
91
screw s
&
Bolts
Gaskets
Plug Tap Low Carbon
Cat. No.
Size
270006
270008
270011
270012
270015
270018
270022
#6-32
#8-32
#10-32
1/4"-20
5/16"-18
3/8"-16
1/2"-13
Made to order
E
E
E
E
E
E
E
10
10
10
10
5
5
5
WT./UM
0
0
0
0
0
0
0
0.10
0.10
0.10
0.10
0.10
0.10
0.10
Made to order
WT./UM
•
1
1
0.10
0.10
#150 Green Non-Asbestos Gaskets
Cat. No.
Size
box qty.
350001
2" 150#
350002
2-1/2" 150#
350003
3" 150#
350005
4" 150#
350007
5" 150#
350008
6" 150#
350010
8" 150#
350011
10" 150#
Gaskets 1/16" thick.
1
1
1
1
1
1
1
1
T-Handle Tap Wrench
Cat. No.
Size
270050
270052
0-1/4"
#10 - 1/2"
0
0
#150 Green Non-Asbestos
Full Face Gaskets
Cat. No.
Spade Bits
Cat. No.
Size
273009
273013
273015
273017
3/4" x 6"
1" x 6" Wood
1-1/4" x 6"
1-1/2" x 6"
Made to order
WT./UM
1
1
1
1
0.10
0.10
0.10
0.10
0
0
0
0
Size
EC1420
EC3816
1/4"-20
3/8"-16
box qty.
1
1
1
1
1
1
#150 Red Ring Gaskets
Eye Coupler Solid
Cat. No.
Size
353251
2" 150#
353253
3" 150#
353255
4" 150#
353257
5" 150#
353258
6" 150#
353260
8" 150#
Gaskets 1/16" thick.
Cat. No.
Made to order
100
100
1000
500
WT./UM
2.20
3.20
Size
Made to order
box qty.
350023
3" 150#
Gaskets 1/8" thick.
1
Gaskets
Red Ring Full Face Gaskets
Cat. No.
#150 Green Non-Asbestos Gasket Sets
Cat. No.
92
Size
350051
2"
350052
2-1/2"
350053
3"
350055
4"
350057
5"
350058
6"
350060
8"
350061
10"
350062
12"
Gaskets 1/16" thick. all sets include zinc plated A307 bolts and nuts.
box qty.
1
1
1
1
1
1
1
1
1
Size
353005
4" 150#
353402
2-1/2" 300#
353403
3" 300#
353405
4" 300#
353408
6" 300#
353410
8" 300#
Gaskets 1/8" thick.
Made to order
box qty.
1
1
1
1
1
1
Kits
Screw Kits
Anchor Kits
Cat. No.
Size
(no photo available)
008933
#6 Combo Plastic Anchor Kit
Cat. No.
Count
C
UM box qty.
C
10
Size
MSTR. PK.
WT./UM
10
XX.XX
008943 Hex Washer Head Tek Screw Kit
8 x 1/2”
100 qty.
10 x 3/4” 35 qty
50 qty.
30 qty.
8 x 3/4”
10 x 1”
8 x 1” 40 qty.
1/4” Hex Driver
1
10 x 1/2”
50 qty.
5/16” Hex Driver
1
10
17.11
008947 #10 Pan Combo Tap Screw Kit
10 x 1/2”
70 qty.
10 x 1-1/4” 30 qty.
10 x 3/4”
50 qty.
10 x 1-1/2” 25 qty.
10 x 1”
35 qty.
10 x 2” 20 qty.
008986 6/32" Round Head Machine Screw Kit
6-32 x 1/2"
100 qty.
6-32 x 1-1/4" 40 qty.
6-32 x 3/4"
60 qty.
6-32 x 1-1/2" 35 qty.
50 qty.
25 qty.
6-32 x 1"
6-32 x 2"
008987 #8 Hex Washer Screw Kit
8 x 1/2"
100 qty.
8 x 1-1/2"
25 qty.
8 x 3/4"
60 qty.
8 x 2"
25 qty.
8 x 1"
40 qty.
5/16” Hex Driver
1
8 x 1-1/4"
35 qty.
10
18.75
10
13.30
10
16.90
008988 #10 Hex Washer Screw Kit
10 x 1/2"
60 qty.
10 x 3/4"
40 qty.
10 x 1"
35 qty.
10 x 1-1/4"
30 qty.
10
17.75
WT./UM
6.25
SCREW S
KITS
&
008937
008939
008941
#10 x 1-1/4" Pan Head Anchor Kit
10 -12 Bantam Anchors
100 qty.
10 x 1-1/4" Tapping Pan
Combo Screws
100 qty.
1
1/4 C/T Drill Bit
#10 x 1-1/4" Hex Head Anchor Kit
10 x 1-1/4" Bantam Anchors
100 qty.
10 x 1-1/4" Hex Washer Hd Screws100 qty.
1/4 C/T Drill Bit
1
5/16 Hex Driver 1
#10 x 1" Hex Head Anchor Kit
10 x 1" Bantam Anchors
100 qty
10 x 1" Hex Washer Hd Screws 100 qty
1/4 C/T Drill Bit
1
5/16 Hex Driver
1
008948
#10 Super Yellow Anchor Kit
C
C
C
C
C
C
C
C
10
10
10
10
50 qty.
40 qty.
40 qty.
11.92
BO LTS
008932 6-32 Truss Head Combo Machine Screw Kit
6-32 x 1/2" 100 qty.
6-32 x 1-1/4" 6-32 x 3/4" 6-32 x 1-1/2" 90 qty.
6-32 x 3/4" 6-32 x 2" 65 qty.
12.55
10.70
11.00
10 x 1-1/2"
60 qty.
10 x 2"
20 qty.
5/16” Hex Driver
1
93
screw s
&
Bolts
kits
008989 6/32" Machine Screw Kit Flat Head Phillips
6/32 x 1/2"
100 qty.
6/32 x 1-1/4"
6/32 x 3/4"
6/32 x 1-1/2"
100 qty.
6/32 x 1"
6/32 x 2"
75 qty.
10
16.26
10
16.44
55 qty.
45 qty.
40 qty.
008990 6/32"Machine Screw Kit Flat Head Slotted
6/32 x 1/2"
100 qty.
6/32 x 1-1/4" 55 qty.
6/32 x 3/4"
100 qty.
6/32 x 1-1/2" 45 qty.
6/32 x 1"
75 qty.
6/32 x 2"
40 qty.
008998 10-32 Machine Screw Kit Round Combo Head
10-32 x 1/2" 75 qty.
10-32 x 1-1/4" 30 qty.
10-32 x 3/4" 50 qty.
10-32 x 1-1/2" 25 qty.
10-32 x 1"
10-32 x 2"
40 qty.
25 qty.
10
22.15
008994 6-32 W
all Plate Kit Painted Machine Screws
White 6-32 x 1/2" 50 qty.
Nickel 6-32 x 1/2" 50 qty.
Ivory 6-32 x 1/2" 50 qty.
Black 6-32 x 1/2" 50 qty.
Brown 6-32 x 1/2" 50 qty.
Zinc 6-32 x 1/4" 25 qty.
10
15.30
Washer and Nut Kits
008991 8/32" M
achine Screw Kit Round Head
8/32 x 1/2"
100 qty.
8/32 x 1-1/4"
60 qty.
8/32 x 3/4"
8/32 x 1-1/2"
8/32 x 1"
50 qty.
8/32 x 2"
10
Size
008995
Flat Washer Kit
#8 SAE
100 qty.
#10 SAE
100 qty.
19.28
1/4" USS
5/16" USS
3/8" USS
Count box qty.
WT./UM
10
20.10
10
27.05
10
20.29
100 qty.
35 qty.
35 qty.
40 qty.
35 qty.
25 qty.
008992 10-24Machine Screw Kit Round Combo Head
10/32 x 1/2"
75 qty.
10/32 x 1-1/4" 30 qty.
10/32 x 3/4"
50 qty.
10/32 x 1-1/2" 25 qty.
40 qty.
25 qty.
10/32 x 1"
10/32 x 2"
008993 1/4-20 Machine Screw Kit Round Combo Head
1/4-20 x 3/8" 40 qty.
1/4-20 x 1-1/4" 20 qty.
1/4-20 x 1/2" 35 qty.
1/4-20 x 1-1/2" 15 qty.
1/4-20 x 1"
30 qty.
1/4-20 x 2"
12 qty.
94
Cat. No.
10
10
008996
Fender Washer Kit
3/16 x 1-1/4" 40 qty.
1/4 x 1-1/4" 40 qty
3/8 x 1-1/4" 40 qty
008997
Finished Hex Nut Kit
6-32
100 qty.
100 qty.
8-32
10-32
100 qty.
20.70
21.40
1/4-20
5/16-18
3/8-16
50 qty.
35 qty.
20 qty.
electrical products
SCREW S
Electrical Products
Pig Tails with Grounding Screw
Cat. No.
Size
079105
079110
7" 12 Ga
10" 12Ga
Made to order
C
C
50
25
WT./UM
WT./UM
Stud Guard
Cat. No.
Size
Made to order
079111 1-1/2" x 2-1/2" Galvanized 2 Hole
079115 1-1/2" x 2-3/4" 16 Gauge
079118 1-1/2" x 5" 20 Gauge
C
C
C
580
580
100
100
0
0
3-Piece Knock-Out Seals
Stainless Steel Type 316
Cat. No.
Size
079520
079521
079522
079523
079524
079525
079526
079527
079528
079529
1/2"
3/4"
1"
1-1/4"
1-1/2"
2"
2-1/2"
3"
3-1/2"
4"
Made to order
u/m
CC
box Qty.
Ctn. Qty
C
C
C
C
C
C
C
C
C
C
580
580
580
580
580
580
580
580
580
580
100
50
25
25
10
10
10
10
10
10
1000
500
250
250
100
100
100
30
30
30
BO LTS
1.35
0.60
&
500
500
Reducing Washers
Cat. No.
Size
079402
079403
079404
079405
079406
079407
079408
079409
079410
079411
079412
079413
079414
079415
079416
079419
079420
079421
079422
079427
079428
079429
079443
079444
079445
3/4 x 1/2"
1 x 1/2"
1 x 3/4"
1-1/4" x 1/2"
1-1/4" x3/4"
1-1/4" x 1
1-1/2 x 1/2"
1-1/2 x 3/4"
1-1/2 x 1
1-1/2 x 1-1/4"
2 x 1/2"
2 x 3/4"
2 x 1"
2 x 1-1/4"
2 x 1-1/2"
2-1/2 x 1
2-1/2 x 1-1/4"
2-1/2 x 1-1/2"
2-1/2 x 2"
3 x 1-1/2"
3 x 2"
3 x 2-1/2"
4 x 2"
4 x 2-1/2"
4 x 3"
Made to order
•
•
•
•
•
•
•
•
•
u/m
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
-C
C
C
C
C
C
C
C
C
CC box qty.
540
540
540
540
540
540
540
540
540
540
540
540
540
540
540
540
540
540
540
540
540
540
540
540
540
100
100
100
50
50
50
50
50
50
50
25
25
25
25
25
25
25
25
25
10
10
10
10
10
10
Ctn. Qty.
2000.00
1000.00
1000.00
1000.00
1000.00
1000.00
500.00
500.00
500.00
500.00
250.00
250.00
250.00
250.00
250.00
250.00
250.00
250.00
250.00
100.00
100.00
100.00
50.00
50.00
50.00
Knock-Out Seals Stainless Steel Type 316
Cat. No.
Size
079500
079501
079502
079503
079504
079505
1/2"
3/4"
1"
1-1/4"
1-1/2"
2"
Made to order
u/m
CC
box Qty.
Ctn. Qty.
C
C
C
C
C
C
580
580
580
580
580
580
100
100
100
50
50
50
1000
1000
500
500
250
250
95
Innovative
fastening
&
anchoring
P r o duc t s
Your One Stop
Anchor
Shop.
Powers Fasteners has been
a worldwide pioneer in the
fastening industry since 1921
and today is one of the leading
suppliers of concrete and masonry
anchors and fastening systems in
North America.
Powers has extensive engineering
and manufacturing expertise in
several product groups, including
mechanical anchors, adhesive
anchoring systems and powered
forced-entry systems such as
powder-actuated and gas
fastening systems.
Adhesive Anchoring
High performance adhesive systems
designed for use by the most
demanding job site conditions.
Mechanical Anchoring
Anchoring Software
The leader in code approved
mechanical anchor systems for the
construction industry.
Anchor software developed
to visualize, quickly calculate,
and specify concrete anchors in
accordance with ACI 318 and
CSA A23.3.
701 E. Joppa Road, Towson, MD 21286 • (800) 524-3244 • email: [email protected] • www.powers.com
Powers Fasteners Branch Information
Usa Locations
For Us Customer Service
1-800-524-3244
City
Address
Phone
Fax
Alabama
5405 Buford Hwy Suite 410 Norcross, GA 30071-3984
678-966-0000
678-966-9242
Atlanta
6115-C Jimmy Carter Blvd, Norcross, GA 30071
770-246-1710
678-966-9242
Boston
2 Powers Lane, Brewster, NY 10509
800-524-3244
877-871-1965
Charlotte
349 L West Tremont Avenue, Charlotte, NC 28203
704-375-5012
704-376-5517
Chicago
2472 Wisconsin Avenue, Downers Grove, IL 60515
630-960-3156
630-960-3912
Dallas
1300 IH 35 North, Suite #118, Carrollton TX 75006
972-446-5985
972-446-3674
Denver
700 West Mississippi Ave, Unit B-1, Denver, CO 80223
303-922-9202
303-922-9228
Detroit
21600 Wyoming Avenue, Oak Park, MI 48237
248-543-8600
248-543-8601
Florida
2412 Lynx Lane, Orlando, FL 32804
813-626-4500
813-626-4545
Houston
13833 North Promenade, Suite 100, Stafford, TX 77477
281-491-0351
281-491-0367
Indianapolis
15290 Stony Creek Way, Noblesville, IN 46060
317-773-1668
317-773-1690
Los Angeles
2761 Dow Avenue, Tustin, CA 92780
714-731-2500
714-731-2566
Maryland
3137-B Pennsy Drive, Landover, MD 20785
301-773-1722
301-341-5119
Milwaukee
1650 Miller Parkway, Milwaukee, WI 53214
414-645-8821
414-466-3993
Minneapolis
351 Wilson Street, NE Minneapolis, MN 55413
612-331-3770
612-331-3549
Missouri
3225 Harvester Road, Kansas City, KS 66115
816-472-5033
816-472-5040
New Orleans
13833 North Promenade, Suite 100, Stafford, TX 77477
281-491-0351
281-491-0367
New York
800-524-3244
877-871-1965
Philadelphia
800-524-3244
877-871-1965
Phoenix
3602 E. Southern Ave, Suite 5 Phoenix, AZ 85040
602-431-8024
602-431-8027
Pittsburgh
800-524-3244
877-871-1965
Portland
18609 72nd Avenue South, Kent, WA 98032-1082
425-251-0312
844-483-4243
425-251-0369
844-303-1784
Rochester
245 Summit Point Drive - Suite 2A, Rochester, NY 14467
800-524-3244
585-334-7071
877-871-1965
585-529-5319
Salt Lake City
3120 W. California Ave, Suite E, Salt Lake City, UT 84104
801-466-9428
801-466-3083
San Francisco
28970 Hopkins Street, Suite D, Hayward, CA 94545
510-293-1500
510-293-1505
Seattle
18609 72nd Avenue South, Kent, WA 98032-1082
425-251-0312
844-483-4243
425-251-0369
844-303-1784
Tennessee
221 Blanton Avenue, Nashville, TN 37210
615-248-2667
615-248-2676
Note: The information and data contained within this documentation was current as of January 2016. The information is for marketing purposes only and is subject to change and updates as needed.
Powers Fasteners, Inc. reserves the right to change designs and specifications without notice or liability for such changes. Please contact Powers Fasteners for the most current and up to date available
information or refer to our website at www.powers.com
Powers Fasteners, 701 E. Joppa Road, Towson, MD 21286 P: (800) 524-3244 F:(877) 871-1965 www.powers.com
©2016 Powers Fasteners, Inc.
701 E. Joppa Road, Towson, MD 21286 U.S.A.
P: (800) 524-3244 F:(877) 871-1965
www.powers.com
Powers Fasteners Canada Ltd.
6275 Millcreek Drive
Mississauga Ontario L5N-7KN Canada
P: 1(800) 567-7188 F:1(800) 265-9680

Buyers Guide - Powers Fasteners

Transcription

Similar documents