MAGICO Q7 User`s Guide

MAGICO Q7 User’s Guide
© 2013 MAGICO LLC
1 MAGICO Q7 User’s Guide
THANK YOU FOR PURCHASING THE MAGICO Q7 LOUDSPEAKERS.
THE Q7 INCORPORATES ALL WE HAVE LEARNED IN THE PAST 20 YEARS ABOUT
LOUDSPEAKER DESIGN AND MANUFACTURING. LIKE ALL MAGICO LOUDSPEAKERS, THE Q7
IS A PRECISION INSTRUMENT FOR MUSIC REPRODUCTION. PROPERLY SET UP AND
MAINTAINED, IT WILL PROVIDE YOU WITH A GREAT MUSICAL EXPERIENCE FOR MANY
YEARS.
BEFORE UNPACKING AND PLAYING YOUR SPEAKERS, PLEASE READ THE FOLLOWING
MANUAL FULLY. IT WILL PROVIDE YOU WITH DIRECTIONS FOR PROPERLY SETTING UP,
POSITIONING, CONNECTING, AND CARING FOR YOUR SPEAKERS. FOLLOWING THESE
INSTRUCTIONS WILL ENSURE A SMOOTH INSTALLATION AND OPTIMUM SPEAKER
PERFORMANCE.
IF YOU HAVE ANY QUESTIONS, PLEASE CONTACT YOUR AUTHORIZED MAGICO DEALER.
MAGICO MAINTAINS A NETWORK OF DEDICATED DISTRIBUTORS WHO WILL BE ABLE TO
HELP YOU, SHOULD YOU HAVE ANY PROBLEMS YOUR DEALER CANNOT RESOLVE. FOR THE
LATEST INFORMATION ON ALL MAGICO PRODUCTS, PLEASE VISIT OUR WEBSITE,
WWW.MAGICO.NET.
I WISH YOU MANY HOURS OF LISTENING PLEASURE.
KINDEST REGARDS,
ALON WOLF, CEO
MAGICO LLC
© 2013 MAGICO LLC
2 MAGICO Q7 User’s Guide
WARNING
The Q7 uses a tweeter equipped with a Beryllium dome, allowing a frequency range
extending beyond 40kHz. In its solid form, Beryllium is harmless. However, due to its
nature, certain special precautions should be observed to avoid exposure to unnecessary
risk such:
• Under no circumstances should the Beryllium dome be subjected to any form of abrasive
action.
• In the unlikely case of damage to the dome, of any form, a wide piece of adhesive tape
should be immediately used to seal the whole front surface of the tweeter. You should
then inform the dealer from whom you purchased the product so that the tweeter can be
removed and replaced by a professional.
• If the dome is broken in any way giving rise to loose particles of Beryllium, these should
be carefully collected with the use of an adhesive tape and sealed in a zip-top bag to be
returned with the tweeter.
© 2013 MAGICO LLC
3 MAGICO Q7 User’s Guide
MAGICO Q7 UNPACKING INSTRUCTIONS
Required: 3 people, Flat-head screwdriver, and socket wrench with ½” and ¾” socket bits.
Position crate on same level as listening position, with at least 12 feet in front of the crate
and 4 feet behind the crate. Using a flat-head screwdriver pry off four clamps from door,
careful to hold the opposite side of the clamp to prevent it popping off. Lay the ramp onto
the floor.
Using a ½” socket bit with either a wrench or power drill, remove 3 bolts from the bottom
of each of the three remaining sides of the crate. (9 total)
© 2013 MAGICO LLC
4 MAGICO Q7 User’s Guide
With one person on either side of the crate walls, lift straight up and backwards, removing
the walls of the crate. Set walls aside. The speaker will be sitting free on the base.
Disengage the brakes on the casters; position the casters parallel to the ramp and facing
the back of the crate for smooth removal.
Using a ¾” socket wrench, turn the bolt at the base of the speaker clockwise until the ‘C’
shaped piece of wood can be slid out from underneath. With the wood removed turn the
same bolt counter clockwise to lower the foam platform to the base of the crate.
© 2013 MAGICO LLC
5 MAGICO Q7 User’s Guide
With one person behind the speaker and two in front, Push/pull the speaker towards the
ramp. Apply pressure to the sides of the front of the speaker, careful not to touch the
drivers, to ease the speaker straight down the ramp and onto the floor. Remove the crate.
Push speaker as close to listening position as possible. Remove the velvet bag, protective
plastic, and tweeter guard. Keeping the speakers on casters, play music and attempt to
position them as close to the ideal listening position as possible. Refer to Q7 Lift Kit and
foot installation manual to jack up the speaker, remove the casters and apply the feet.
© 2013 MAGICO LLC
6 MAGICO Q7 User’s Guide
USING THE Q7 LIFT KIT
REQUIRED ITEMS:
•
•
•
•
•
Q7 lift plate
Q7 lift foot bracket (x3)
3/8” drive socket wrench (x3)
3/8” drive 15mm - 12 point socket (x3)
Q7 foot assembly (x4)
DIRECTIONS
© 2013 MAGICO LLC
7 MAGICO Q7 User’s Guide
STEP 1: Roll the Q7 loud-speaker cabinet into the approximate desired listening area.
With the casters positioned as shown above.
STEP 2:
Slide the rear extension of the Q7 lift plate, padded side up, between the two
rear casters. And then slide right side to the other side of the speaker.
STEP 3:
With one person at the front and back of the loud-speaker, work together to
lift the Q7 lift plate from the ground so the padded material sits flush with the bottom
© 2013 MAGICO LLC
8 MAGICO Q7 User’s Guide
plate. Position the plate beneath the loud-speaker as shown below. Make certain that the
front extensions do not impede upon the embossed circular reliefs that the casters are
seated in.
STEP 4:
Seat the (3) Q7 lift foot brackets at the end of each of the (3) lift extensions.
Make certain that the bolt heads of the Q7 foot brackets, on the front lift extensions, are
of approximate equal distance from the side of the cabinet. Once the lift plate is seated,
make sure that the brackets are also securely seated in the notches of the lift plate and
that they are perpendicular to each other, with the bolts being perpendicular to the floor
as well. Incorrectly angled placement of the brackets can put both the speaker and the
installer in harm's way.
© 2013 MAGICO LLC
9 MAGICO Q7 User’s Guide
STEP 5:
One person man each of the lift extensions/foot brackets with a 3/8” drive
socket wrench and 15mm 12 point bit. Work together to counting out sets of 10 x 180
degree cranks. This is to ensure that the loud-speaker cabinet is lifted on a level plane.
Always make sure that as lift is being cranked that the bearing is moving in concert with
the bolt. Always make sure that the foot is not turning with the bearing, as this will
damage the foot and the floor.
NOTE:
It is important to take a step back after every (3)
sets of (10) 180 degree cranks to ensure that the loud-speaker is still level with the floor.
If not, jack the appropriate side to compensate.
STEP 6:
Once the Jacking bolt heads bottom out against the Q7 lift foot brackets,
remove the caster and replace each with a Q7 foot assembly. Before the Q7 foot
assemblies are installed, the two pieces should be separated so there is approximately ¼”
of space between the base and top piece.
NOTE:
This can be adjusted after the loud-
speaker is lowered with the supplied spanners in the accessory kit.
STEP 7:
Reverse steps (5-1) to remove the lift from below the loud-speaker cabinet.
WARNING/DISCLAIMER:
•
•
•
Never place hands underneath speaker without someone holding the speaker
steady. There should always be a spotter who is not actually helping lift the
speaker.
Never attempt to tilt speaker by hand.
Never crank the bolts at a speed that rocks the speaker, with gentle cranks the
speaker will rise smoothly and safely.
© 2013 MAGICO LLC
10 MAGICO Q7 User’s Guide
SPEAKER PLACEMENT AND POSITIONING
THE MAGICO Q7 LOUDSPEAKERS ARE PRECISION INSTRUMENTS FOR MUSIC REPRODUCTION. AS
SUCH, PROPER CARE AND ATTENTION TO DETAIL WHEN SETTING UP THESE SPEAKERS WILL YIELD
THE MAXIMUM PERFORMANCE, REGARDLESS OF THE PARTICULAR ROOM. FOLLOWING THESE SETUP GUIDELINES WILL ENSURE THE SPEAKERS ARE PROPERLY POSITIONED TO DELIVER THE
OPTIMUM LISTENING EXPERIENCE. ALL THAT IS REQUIRED IS A TAPE MEASURE, A PEN, A
CALCULATOR, A BALL OF STRING, A COUPLE OF DEMO CDS, AND SOME PATIENCE.
PLACEMENT—Q7s IN RELATION TO BACK AND SIDE WALLS
BEFORE YOU BEGIN: LOOK FOR OBVIOUS IMPEDIMENTS INCLUDING ANYTHING THAT COULD
IMPEDE OR DIMINISH THE SOUND—E.G., OTHER SPEAKERS, AMPLIFIERS, EQUIPMENT RACKS,
ANYTHING ON THE WALL THAT COULD CAUSE A REFLECTION, A SEVERE MISMATCH IN QUALITY
AMONG INDIVIDUAL COMPONENTS, AND UNNECESSARY OR POORLY RUN
SPEAKER/INTERCONNECT CABLES.
BASS—DISTANCE FROM REAR WALL
THE INITIAL PLACEMENT SHOULD BE APPROXIMATELY 20 INCHES (1/2 M) FROM THE BACK
OF THE LOUDSPEAKER TO THE BACK WALL. SINCE WE HAVE SHORT AUDITORY MEMORY, THE
SELECTED DEMO MUSIC CUT SHOULD BE BRIEF—30 SECONDS – 1 MINUTE MAX. IT SHOULD BE A
WELL RECORDED JAZZ CUT WITH GOOD BASS GUITAR OR PERCUSSION. WHAT WE ARE LISTENING
FOR AT THIS TIME IS THE DEFINITION OF THE BASS AND THE RIGHT SENSE OF PROPORTION.
NEXT, MOVE THE SPEAKER 6 – 8 INCHES (15 – 20 CM) FORWARD AND REPEAT THE
LISTENING PROCESS. REPEAT THIS PROCESS, MOVING THE LOUDSPEAKER FORWARD IN 6 – 8
INCH (15 -20 CM) INCREMENTS. WHEN YOU REACH THE POINT FROM WHICH MOVING THE
SPEAKER FORWARD SOUNDS WORSE THAN THE PREVIOUS LISTENING POINT, MOVE THE
LOUDSPEAKER BACK TO THIS POSITION AND MARK THIS DISTANCE FROM THE REAR WALL.
MIDRANGE—PLACEMENT IN RELATION TO SIDE WALLS
FOR LATERAL PLACEMENT, BEGIN BY DIVIDING THE ROOM WIDTH BY 14. INITIAL
PLACEMENT OF THE LOUDSPEAKERS WILL BE AT 3 AND 11. THE DISTANCE FROM THE
LOUDSPEAKER TO THE EARS HAS TO BE PRECISELY EQUAL. THIS MEASUREMENT IS CRITICAL. THE
MUSIC FOR THIS PROCESS SHOULD BE A FEMALE VOICE AND PIANO. WE ARE LISTENING FOR THE
IMAGE OF HER VOICE TO BE FOCUSED. THE RULE FOR THE TOE-IN IS TO PICK A POINT
APPROXIMATELY 1 – 2 FEET (½ M) BEHIND THE LISTENER’S HEAD. TOE THE LOUDSPEAKERS IN TO
© 2013 MAGICO LLC
11 MAGICO Q7 User’s Guide
INTERSECT AT THAT POINT. IF THE SOUND IS TOO BRIGHT, TOE THE SPEAKERS OUT A LITTLE
MORE. IF THE SOUND IS TOO DULL, TOE THE SPEAKERS IN A LITTLE MORE.
REPEAT THE ABOVE PROCESS WITH THE LOUDSPEAKERS AT THE 4 AND 10 POSITION. THEN
REPEAT, ONCE AGAIN WITH THE SPEAKERS AT THE 5 AND 9 POSITION.
SUMMARY
ONCE THE INITIAL PROCESS HAS BEEN COMPLETED, RETURN TO THE BASS SET-UP TO
ENSURE THAT THE LOUDSPEAKERS ARE THE PROPER DISTANCE FROM THE BACK WALL. WHEN THE
PROCESS HAS BEEN COMPLETED, MARK THE SPEAKER LOCATION WITH TAPE SO THAT THE
SPEAKERS CAN BE RETURNED THERE FOR FURTHER LISTENING.
POSITIONING—Q7s IN RELATION TO THE LISTENER
•
THE SPEAKERS AND THE LISTENER SHOULD FORM AN ISOSCELES TRIANGLE.
•
THE LISTENER SHOULD BE EXACTLY EQUIDISTANT BETWEEN THE TWO
LOUDSPEAKERS. THE BEST WAY TO DETERMINE THIS IS WITH A PIECE OF STRING. PICK A
FIXED SPOT AT THE LISTENING POSITION. RUN THE STRING FROM THIS SPOT TO THE
FRONT OF THE TWEETER OF THE LEFT SPEAKER. REPEAT THE PROCESS FOR THE RIGHT
SPEAKER. IT IS CRITICALLY IMPORTANT TO KEEP THIS DISTANCE PRECISELY THE SAME.
CONNECTIONS
CONNECTIONS
SHOULD
BE
MADE
WITH
ALL
ELECTRONIC
EQUIPMENT
(AMPLIFIERS,
PREAMPLIFIERS) TURNED OFF. THERE ARE TWO TERMINALS AT THE BACK OF THE SPEAKER. THE
TERMINALS ARE INSULATED TO ACCEPT A VARIETY OF CABLE TERMINATIONS FOR MOST
APPLICATIONS AND TO PREVENT ANY LIKELIHOOD OF ELECTRICAL SHOCK, EVEN WHEN THE
SPEAKERS ARE USED WITH THE HIGHEST POWERED AMPLIFIERS. DO NOT USE TOOLS TO TIGHTEN
THE BINDING POSTS.
BREAK-IN
A LOUDSPEAKER IS A MECHANICAL DEVICE AND AS SUCH REQUIRES AN EXTENDED INITIAL
PERIOD OF NORMAL USE DURING WHICH A NOTICEABLE IMPROVEMENT IN SOUND QUALITY WILL
OCCUR. DO NOT ATTEMPT TO ACCELERATE THE BREAK-IN PROCESS BY PLAYING SINE WAVES,
TONE SWEEPS, BREAK-IN CDS OF ANY SORT, OR OTHER GENERATED SIGNALS.
© 2013 MAGICO LLC
12 MAGICO Q7 User’s Guide
CARE:
FOR ALUMINUM PANELS USE A LINT-FREE SOFT CLOTH (PROVIDED IN ACCESSORY KIT),
DAMPENED ONLY WITH WARM, SLIGHTLY SOAPY WATER (A SMALL DROP OF DISH SOAP WILL DO).
DO NOT USE CLEANERS THAT CONTAIN AMMONIA, STRONG SOLVENTS, OR ABRASIVE MATERIALS.
USE OF THESE CLEANERS CAN DEGRADE, SCRATCH, OR DESTROY THE FINISH.
SPECIFICATIONS
DESCRIPTION:…………………………………...……………..………………………4-WAY SEALED ENCLOSURE
FREQUENCY RESPONSE:………………………………………..……………(+/- 2dB) 20HZ – 50KHZ (IN ROOM)
SENSITIVITY (2.8V/1M):…………………………..……………………..……...…………….…..……….94dB/WATT
NOMINAL IMPEDANCE:………………….…………………………………………………………………………. 4 OHMS
POWER HANDLING……………………………………………….………………………….…………… 50-1200 WATTS
DIMENSIONS (HXDXW):…………………..…….....……….......... 60” X 32” X 15” (152cm x 81cm x 38cm)
WEIGHT:………………………………...…….……………………………..……………………...…….. 750 LBS (340 kg)
© 2013 MAGICO LLC
13 MAGICO Q7 User’s Guide
LIMITED WARRANTY
DEAR MAGICO PURCHASER,
THIS PRODUCT HAS BEEN DESIGNED AND MANUFACTURED TO THE HIGHEST QUALITY
STANDARDS. HOWEVER, IF SOMETHING DOES GO WRONG WITH THIS PRODUCT,
MAGICO LLC
AND ITS NATIONAL DISTRIBUTORS WARRANT THE REPLACEMENT OF DEFECTIVE PARTS
INCLUDING LABOR (EXCLUSIONS MAY APPLY) IN ANY COUNTRY SERVED BY AN OFFICIAL
MAGICO LLC DISTRIBUTOR. THIS LIMITED WARRANTY IS VALID FOR A PERIOD OF 5 YEARS
FROM THE DATE OF PURCHASE.
TERMS AND CONDITIONS
1.
THE WARRANTY IS LIMITED TO THE REPAIR OF THE EQUIPMENT. IN THE EVENT THAT THIS
LOUDSPEAKER REQUIRES SERVICE, THE CUSTOMER MUST FIRST OBTAIN A RETURN
AUTHORIZATION FROM MAGICO OR ITS AUTHORIZED DISTRIBUTOR. THE CUSTOMER IS
RESPONSIBLE FOR RETURNING THE LOUDSPEAKER TO MAGICO OR ITS AUTHORIZED
DISTRIBUTOR. IN THE EVENT THAT THE REPAIR IS DETERMINED TO BE UNDER WARRANTY,
MAGICO WILL RETURN THE LOUDSPEAKER TO THE CUSTOMER AT NO CHARGE. EXCEPT AS
INDICATED, NEITHER TRANSPORTATION, SHIPPING, NOR ANY OTHER COSTS, NOR ANY RISK FOR
REMOVAL, TRANSPORTATION AND INSTALLATION OF PRODUCTS IS COVERED BY THIS WARRANTY.
2.
WITH THE EXCEPTION EXPLAINED BELOW, THIS WARRANTY IS ONLY VALID FOR THE ORIGINAL
OWNER. IT IS NOT TRANSFERABLE. IT IS VALID ONLY WHEN PURCHASED FROM AN AUTHORIZED
MAGICO DEALER. A VALID RECEIPT SHOWING THE PURCHASER’S NAME, DATE OF PURCHASE, AND
DEALER INFORMATION MUST BE SUBMITTED WITH ALL WARRANTY CLAIMS.
2A. IN THE EVENT THAT THIS LOUDSPEAKER IS PURCHASED AS A USED OR TRADE-IN
LOUDSPEAKER FROM AN AUTHORIZED MAGICO DEALER OR DISTRIBUTOR, THE SECOND OWNER SHALL
RECEIVE THE BALANCE OF THE ORIGINAL WARRANTY BASED UPON THE ORIGINAL DATE OF PURCHASE.
VALID RECEIPTS SHOWING THE PURCHASER’S NAME, DATE OF PURCHASE, AND DEALER INFORMATION
FOR THE CURENT OWNER AND THE ORIGINAL PURCHASE MUST BE SUBMITTED WITH ALL WARRANTY
CLAIMS.
© 2013 MAGICO LLC
14 MAGICO Q7 User’s Guide
3.
THIS WARRANTY WILL NOT BE APPLICABLE IN CASES OTHER THAN DEFECTS IN MATERIALS
AND/OR WORKMANSHIP AT THE TIME OF PURCHASE AND WILL NOT BE APPLICABLE FOR
DAMAGES CAUSED BY INCORRECT INSTALLATION, CONNECTION OR PACKING, FOR DAMAGES
CAUSED BY ANY USE OTHER THAN CORRECT USE DESCRIBED IN THE USER MANUAL, NEGLIGENCE,
MODIFICATIONS, OR USE OF PARTS THAT ARE NOT MADE OR AUTHORIZED BY MAGICO LLC, FOR
DAMAGES CAUSED BY FAULTY OR UNSUITABLE ANCILLARY EQUIPMENT, FOR DAMAGES CAUSED BY
ACCIDENTS, LIGHTNING, WATER, FIRE HEAT, EXTREME WEATHER CONDITION, WAR, PUBLIC
DISTURBANCES OR ANY OTHER CAUSE BEYOND THE REASONABLE CONTROL OF MAGICO LLC AND
ITS APPOINTED DISTRIBUTORS, FOR PRODUCTS WHOSE SERIAL NUMBER HAS BEEN ALTERED,
DELETED, REMOVED OR MADE ILLEGIBLE, IF REPAIRS OR MODIFICATIONS HAVE BEEN EXECUTED
BY AN UNAUTHORIZED PERSON.
4.
THIS GUARANTEE COMPLEMENTS ANY NATIONAL/REGIONAL LAW OBLIGATIONS OF DEALERS
OR NATIONAL DISTRIBUTORS AND DOES NOT AFFECT YOUR STATUTORY RIGHTS AS A CUSTOMER.
5.
UNAUTHORIZED DISMANTLING OF THIS PRODUCT WILL RENDER THIS WARRANTY VOID.
MAGICO LLC STRIVES TO MANUFACTURE THE VERY FINEST POSSIBLE EQUIPMENT, AND THEREFORE
RESERVES THE RIGHT TO MAKE CHANGES OR IMPROVEMENTS WITHOUT NOTICE.
6.
SERIAL NUMBERS
PLEASE TAKE THE TIME TO RECORD YOUR SPEAKERS’ SERIAL NUMBERS BELOW.
_______________________________________________________________________
© 2013 MAGICO LLC
15 MAGICO Q7 User’s Guide
DISCLAIMER
MAGICO LLC MAKES THIS MANUAL AND THE CONTAINED INFORMATION AVAILABLE ON AN "AS
IS" BASIS. ALL WARRANTIES AND REPRESENTATIONS OF ANY KIND WITH REGARD TO SAID
INFORMATION IS DISCLAIMED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR USE. UNDER NO CIRCUMSTANCES WILL MAGICO LLC, OR ANY OF
ITS OFFICERS OR EMPLOYEES BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, SPECIAL OR
EXEMPLARY DAMAGES EVEN IF APPRISED OF THE LIKELIHOOD OF SUCH DAMAGES OCCURRING.
MAGICO LLC DOES NOT WARRANT THE INFORMATION AGAINST DEFICIENCIES OF ANY KIND.
COMPANY INFORMATION
MAGICO LLC
3170 CORPORATE PL.
EMAIL: [email protected]
PHONE: +1.510.649.9700
HAYWARD, CA 94545
U.S.A.
FAX: +1.510.323.4774
BUSINESS HOURS: 8 AM – 4 PM PST
© 2013 MAGICO LLC
16