Service Manual of Sony DSC

Transcription

DSC-W5/W7/W15/W17
SERVICE MANUAL
LEVEL
2
DSC-W5/W7
Ver. 1.5 2007.09
US Model
Canadian Model
Argentine Model
Brazilian Model
Japanese Model
Revision History
DSC-W5/W7/W15/W17
AEP Model
UK Model
E Model
Australian Model
Hong Kong Model
Korea Model
Tourist Model
How to use
Acrobat Reader
DSC-W5/W7/W15
Chinese Model
Photo: DSC-W5/Silver
Link
•
•
•
•
•
•
•
•
SPECIFICATIONS
BLOCK DIAGRAMS
PRINTED WIRING BOARDS
SERVICE NOTE
FRAME SCHEMATIC DIAGRAM
REPAIR PARTS LIST
DISASSEMBLY
SCHEMATIC DIAGRAMS
For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (9-876-856-51).
For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (9-876-856-41).
This service manual contains information for Japanese model as well.
Reference No. search on printed wiring boards is available.
Table for Differences of Function of Each Model
Note in Lens Frame Installation
Method for Copying or Erasing the Data in Internal Memory.
Exchange Method of Barrier Assy
On the CH-168 and SY-001 boards
This service manual procides the information that is premised the
circuit board replacement service and not intended repair inside the
CH-168 and SY-001 boards.
Therefore, schematic diagram, printed wiring board and electrical
parts list of the CH-168 and SY-001 boards are not shown.
The following pages are not shown.
Schematic diagrams ..................
Printed wiring boards ................
Waveforms ................................
Mounted parts location ..............
Electrical parts list .....................
Pages 4-11 to 4-30
Pages 4-39 to 4-42
Pages 4-45 and 4-46
Pages 4-48
Pages 5-7 and 5-9 to 5-12
DIGITAL STILL CAMERA
The above-described information is shown in service manual Level 3.
DSC-W5/W7/W15/W17
9-876-856-31
Sony EMCS Co.
2007I0500-1
© 2007.9
Published by Kohda TEC
SPECIFICATIONS
Camera
[Input and Output connectors]
BC-CS2A/CS2B Ni-MH battery charger
[System]
A/V OUT (MONO) jack (Monaural)
Minijack
Video: 1 Vp-p, 75 Ω,
unbalanced, sync negative
Audio: 327 mV (at a 47 kΩ
load)
Output impedance 2.2 kΩ
Power requirements
AC 100 to 240 V, 50/60 Hz,
3W
Image device
DSC-W7/W17:
9.11 mm (1/1.8 type) color
CCD, Primary color filter
DSC-W5/W15:
9.04 mm (1/1.8 type) color
CCD, Primary color filter
Total pixel number of camera
DSC-W7/W17:
Approx. 7 410 000 pixels
DSC-W5/W15:
Effective pixel number of camera
DSC-W7/W17:
DSC-W5/W15:
Lens
Carl Zeiss Vario-Tessar
3 zoom lens
f = 7.9 - 23.7 mm (38 - 114 mm
when converted to a 35 mm still
camera)
F2.8 - 5.2
Exposure control Automatic exposure, Manual
exposure, Scene Selection (7
modes)
White balance
Automatic, Daylight, Cloudy,
Fluorescent, Incandescent,
Flash
File format (DCF compliant)
Still images: Exif Ver. 2.2
JPEG compliant, DPOF
compatible
Movies: MPEG1 compliant
(Monaural)
Recording media Internal memory 32 MB
Memor y Stick
Flash
Recommended distance (ISO
set to Auto): 0.2 m to 4.5 m
(7 7/8 inches to 14 feet 9 1/4
inches) (W)/0.3 m to 2.5 m
(11 7/8 inches to 8 feet 2 1/2
inches) (T)
USB jack
mini-B
USB communication
Hi-Speed USB (USB 2.0
compliant)
Output voltage
AA: DC 1.4V 400 mA × 2
AAA: DC 1.4 V 160 mA × 2
Operating temperature
0°C to +40°C (+32°F to
+104°F)
Storage temperature
−20°C to +60°C (−4°F to
+140°F)
Dimensions
Approx. 71×30×91 mm
(2 7/8×1 3/16×3 5/8 inches)
(W/H/D)
Total number of dots
115 200 (480×240) dots
Mass
Approx. 90 g (3 oz)
[Power, general]
Design and specifications are subject to change
without notice.
[LCD screen]
LCD panel
Power
6.2 cm (2.5 type) TFT drive
HR 15/51:HR6 (size AA)
Nickel-Metal Hydride batteries
(2), 2.4 V
R6 (size AA) Alkaline batteries
(2, not supplied), 3 V
AC-LS5K AC Acaptor (not
supplied), 4.2 V
Power consumption
(during shooting with the LCD screen on)
DSC-W7/W17: 1.2 W
DSC-W5/W15: 1.1 W
Operating temperature
0°C to +40°C (+32°F to
+104°F)
Storage temperature
−20°C to +60°C (−4°F to
+140°F)
Dimensions
91×60×37.1 mm
(3 5/8×2 3/8×1 1/2 inches)
(W/H/D, excluding maximum
protrusions)
Mass
Approx. 253 g (8.9 oz)
(including two batterries and
wrist strap)
Microphone
Electret condenser microphone
Speaker
Dynamic speaker
Exif Print
Compatible
PRINT Image Matching III
Compatible
PictBridge
Compatible
DSC-W5/W7/W15/W17
—2—
Table for differences of function
Model
Destination
CCD imager
Total pixel (Effective pixel)
CD board
Note:
DSC-W5
US, CND, AEP, UK,
E, AUS, HK, CH,
KR, AR, BR, J, JE
DSC-W7
US, CND, AEP, UK,
E, AUS, HK, CH,
KR, AR, BR, J, JE
DSC-W15
AEP, UK,
E, AUS, HK, CH,
KR, JE
DSC-W17
AEP, UK
E, AUS, HK,
KR, JE
5 255 000 pixels
(5 090 000 pixels)
CD-545
7 410 000 pixels
(7 201 000pixels)
CD-546
5 255 000 pixels
(5 090 000 pixels)
CD-545
7 410 000 pixels
(7 201 000pixels)
CD-546
• Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
HK : Hong Kong model
J
: Japanese model
JE : Tourist model
KR : Korea model
DSC-W15/W17 are the same as DSC-W5/W7
except accessories and packing materials.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1.
2.
3.
4.
5.
6.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
Check the B+ voltage to see it is at the values specified.
FLEXIBLE Circuit Board Repairing
• Keep the temperature of the soldering iron around 270°C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
DSC-W5/W7/W15/W17
Unleaded solder
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
—3—
TABLE OF CONTENTS
Section
1.
Title
Page
Section
SERVICE NOTE
1-1. Note for Repair ································································ 1-1
1-2. Discharging of The SY-001 Board’s Charging Capacitor
(C901) ·············································································· 1-1
1-3. Note in Lens Frame Installation ······································ 1-2
1-4. Description on Self-diagnosis Display ···························· 1-2
1-5. Method for Copying or Erasing the Data in Internal
Memory ··········································································· 1-3
1-6. Process After Fixing Flash Error ····································· 1-4
2.
DISASSEMBLY
2-1. Disassembly ····································································· 2-1
2-2. SY-001 Board Service Position ······································· 2-3
2-3. Exchange Method of Barrier Assy ·································· 2-5
2-3-1. Peel Off Old Ornamental Ring A ···································· 2-5
2-3-2. Remove Old Barrier Assy ················································ 2-6
2-3-3. Install New Barrier Assy ················································· 2-6
2-3-4. Adhere the Ornamental Ring A ······································· 2-7
2-4. Circuit Boards Location ·················································· 2-8
3.
BLOCK DIAGRAMS
3-1. Overall Block Diagram (1/2) ··········································· 3-1
3-2. Overall Block Diagram (2/2) ··········································· 3-3
3-3. Power Block Diagram ····················································· 3-5
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1. Frame Schematic Diagram ·············································· 4-1
4-2. Schematic Diagrams ························································ 4-5
CD-545 FLEXIBLE (CCD IMAGER) ··························· 4-7
CD-545 FLEXIBLE (CCD IMAGER) ··························· 4-9
SW-001 BOARD (CONTROL SWITCH) ···················· 4-31
CONTROL SWITCH BLCOK ····································· 4-32
4-3. Printed Wiring Boards ··················································· 4-35
CD-545 FLEXIBLE ······················································ 4-37
CD-546 FLEXIBLE ······················································ 4-38
SW-001 ········································································· 4-44
4-5. Mounted Parts Location ················································ 4-47
5.
REPAIR PARTS LIST
5-1. Exploded Views ······························································· 5-2
5-1-1. Overall Assembly ··························································· 5-2
5-1-2. Cabinet (Front) Block ······················································ 5-3
5-1-3. Main Block Assembly ····················································· 5-4
5-1-4. Lens Block Assembly ······················································ 5-5
5-2. Electrical Parts List ························································· 5-6
DSC-W5/W7/W15/W17
—4—
Title
Page
1. SERVICE NOTE
1-1. NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
When remove a connector, don’t pull at wire of connector.
It is possible that a wire is snapped.
When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
1-2. DISCHARGING OF THE SY-001
BOARD’S CHARGING CAPACITOR
(C901)
Discharging the Capacitor
Short-circuit between the positive and the negative terminals of
charged capacitor with the short jig about 10 seconds.
The charging capacitor (C901) of SY-001 board is charged up to
the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
R:1 kΩ/1 W
(Part code:
1-215-869-11)
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of a
resistor of 1 kΩ /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.
1 kΩ/1 W
Wrap insulating tape.
DSC-W5/W7/W15/W17
1-1
1-3. NOTE IN LENS FRAME INSTALLATION
When tightening a screw, have both sides of the lens block assembly so as not for the load to depend.
P2 tapping screw
Lens block assembly
Lens frame
assembly
1-4. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY
Self-diagnosis display
• C: ss: ss
You can reverse the camera
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)
• E: ss: ss
Contact your Sony dealer or local
authorized Sony service facility.
Display Code
C:32:ss
Countermeasure
Cause
Caution Display During Error
Turn the power off and on again.
Trouble with hardware.
SYSTEM ERROR
Format the “Memory Stick” or internal
memory.
“Memory Stick” or internal memory is
unformatted.
FORMAT ERROR
Insert a new “Memory Stick”.
“Memory Stick” is broken.
MEMORY STICK ERROR
Turn the power off and on again.
Trouble with internal memory.
INTERNAL MEMORY ERROR
E:61:ss
Checking of lens drive circuit.
When failed in the focus and zoom
initialization.
E:91:ss
Checking of flash unit or replacement
of flash unit. (Note)
Abnormality when flash is being
charged.
E:92:ss
Insert batteries correctly.
Batteries are not inserted correctly.
C:13:ss
Note: After repair, be sure to perfom “1-6. PROCESS AFTER FIXING FLASH ERROR”.
DSC-W5/W7/W15/W17
1-2
—
1-5. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)
Note: 1 When replacing the SY-001 board, erase the data in internal memory of the board before replacement.
Note: 2 When replacing the SY-001 board or the IC381 on the SY-001 board, execute formatting and initialize the internal memory after
replacement.
Method for Copying the Data in Internal Memory
Copy
Copies all images in the internal memory to a “Memory Stick”.
OK
See the following procedure.
Cancel
Cancels the copying.
1 Insert a “Memory Stick” having 32 MB or larger capacity.
2 Select [OK] with v on the control button, then press z.
The message “All data in internal memory will be copied Ready?” appears.
3 Select [OK] with v, then z.
Copying starts.
Copying
102_COPY
• Use fully charged Nickel-Metal Hydride batteries or the AC Adaptor (not supplied). If you attempt to
copy image files using batteries with little remaining charge, the batteries may run out, causing copying to
fail or possibly corrupting the data.
• You cannot copy individual images.
• The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the “Memory Stick” after copying, then execute the [Format] command in
Internal Memory Tool).
• You cannot select a folder copied on a “Memory Stick”.
•A
(Print order) mark added to an image is deleted when you copy data.
Method for Formatting the Internal Memory
Format
Formats the internal memory.
• Note that formatting irrevocably erases all data in the internal memory, including even protected images.
OK
Cancel
Cancels the formatting.
The message “All data in internal memory will be erased Ready?” appears.
2 Select [OK] with v, then press z.
The format is complete.
DSC-W5/W7/W15/W17
1-3
1-6. PROCESS AFTER FIXING FLASH ERROR
When “FLASH error” (Self-diagnosis Code E : 91 : ** ) occurs, to prevent any abnormal situation caused by high voltage, setting of the
flash is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the Setup screen.
Method for Initializing the Flash Error Code
Initialize
Initializes the setting to the default setting.
OK
Cancel
Cancels the resetting.
The message “Initialize all settings Ready?” appears.
2 Select [OK] with v, then press z.
The settings are reset to the default setting.
• Make sure that the power is not disconnected during resetting.
DSC-W5/W7/W15/W17
1-4E
2. DISASSEMBLY
The following flow chart shows the disassembly procedure.
2-1. DISASSEMBLY
R:1 kΩ/1 W
(Part code:
1-215-869-11)
qa
0
qs
9
7
9
Note: High-voltage cautions
5
Discharging the Capacitor
Short-circuit between the two
points with the short jig about 10
seconds.
1
0
3
1
1
3
8
6
9
8
6
2
7
4
5
1
2
4
1
2
3
4
5
6
P2 torasuta screw (M1.7) x4
Claw x1
Cabinet (rear) block assembly
Screw (M1.7) x2
SW-001 board
Flexible board x2: CN451, 452
7
8
9
0
qa
qs
Claw x1
BT side cabinet (C)
Claw x3
SP sheet
Connector: CN601
D901, LCD901
1
2
3
4
5
Screw (M1.7) x2
LCD frame
Terminal guard
Fuse label
Remove the control switch block.
6
7
8
9
0
Connector: CN753
Control switch block
Connector x2: CN801, 802
Remove the cabinet (front) block.
Cabinet (front) block
2
1
1 Ornamental ring A
2 Tapping screw x2
3 Barrier assy
12
3
3
Note: When you exchange rings, be sure
to follow the procedure carried on
"2-3. Exchange Method of Barrier
Assy" (2-5 page).
4
DSC-W5/W7/W15/W17
2-1
2-2
1
2
3
4
Connector: CN001
Battery holder
Connector x2: CN201, 401
Lens block
2-2. SY-001 BOARD SERVICE POSITION
Connection cord (DK-2AA)
(1-830-351-11)
Batery holder
qa
AC power
adaptor
qs
9
1
AC IN
SW-001
0
3
1
1
8
6
9
Control switch block
FFC-051
7
4
5
2
SY-001 board
0
9
7
5
A/V cable (Note)
8
6
D901, LCD901
(Note)
3
2
Lens block
Color monitor
1
4
Note: If the A/V cable is connected to the AV OUT (MONO) jack
of SY-001 board, the image can not appear on the LCD
screen.
If you want to confirm the circuit of LCD drive or LCD,
disconnect the A/V cable.
2
1
3
4
DSC-W5/W7/W15/W17
2-3
2-4
2-3. EXCHANGE METHOD OF BARRIER ASSY
2-3-2. REMOVE OLD BARRIER ASSY
Service parts
Part Number
1 Remove two screws.
* Discard the removed screws.
Part Name
Quantity
1
2
3-091-427-01
X-3954-476-1
Ring (A), Ornamental
Barrier Assy
1
1
3
3-086-156-31
Tapping screw (P2)
2
1
2 Remove the Barrier Assy.
* Discard the removed Barrier Assy.
Tools used
Torque driver
Soldering iron
Weight about 60g
Adhesive (Super X) (Note)
Note: Use adhesive (Super X) or an equivalent article.
Don’t use what becomes white after drying like a quick-drying glue.
2
1
2
1
3
* After removing the Barrier Assy, if the “G1 Dust-Proof Ring” was removed, it must be returned to the home position.
In returning the ring, adjust the location of a projection to the lens direction.
This is an important part to prevent the dust and light from coming in.
* After removing the Barrier Assy, take extreme care not to drop dust or foreign substances in the lens barrel.
2-3-1. PEEL OFF OLD ORNAMENTAL RING A
The Ornamental Ring A has adhered to the Barrier Assy strongly and accordingly, use a soldering iron to weaken the adhesive force.
Heat four circled portions with the soldering iron.
Heating temperature is about 300ºC.
Beware of a burn since the entire Ornamental Ring becomes hot.
* As the adhesive force of Ornamental Ring A is considerably large, the forced peeling will damage the group-1 frame.
2-3-3. INSTALL NEW BARRIER ASSY
1 Install new Barrier Assy by paying attention to the projection of the Barrier Assy in relation to the position shown in the under figure.
Insert the tip of tweezers, etc. into a notch of the group-1 frame and prize the ring.
* Take extreme care so as not to damage the coated surface of the group-1 frame.
In case of difficult peeling, heat the ring again with the soldering iron.
If this re-heating failed, it may be advisable that the ring be peeled while heating the portions 1 → 2 → 3 → 4 in the under figure one
by one sequentially.
2 Tighten two screws.
* Tightening torque = 0.5 kgf (4.9 N)
* Discard the removed Ornamental Ring A.
4
Projection
3
2
1
Tip
2
1
2
DSC-W5/W7/W15/W17
2-5
2-6
2-3-4. ADHERE THE ORNAMENTAL RING A
Apply an adhesive to four recesses on the top surface of the Barrier Assy.
* Do not apply too much adhesive. (Make quantity of adhesives into the quantity in which a groove hides.)
Meeting a “notch” of the Ornamental Ring A with a “projection” of the group-1 frame, push the Ornamental Ring A into the group-1 frame.
* The projection of the spring for preventing static electricity must be tilted.
Put the 60g weight on the Ornamental Ring A so that the Ornamental Ring A does not float up until the adhesive hardens.
Note: Be careful not to give a shock.
* After the weight was put, no gap must be present in full circumference between Ornamental Ring A and group-1 frame.
A gap, if present, causes the crackle sound NG.
* The weight must push in the Ornamental Ring A only.
If the weight is put on the mold part of the Barrier Assy, the Ornamental Ring A will float up.
Do not put the weight on a black mold part.
Notch
Adhesive
Adhesive
Adhesive
Projection
Adhesive
Not gap in full circumference.
Completion after 30 minutes.
DSC-W5/W7/W15/W17
2-7
2-4. CIRCUIT BOARDS LOCATION
SW-001
SY-001
(including CP201
(CH-168 board))
CD-545 flexible (W5/W15)/
CD-546 flexible (W7/W17)
Board Name
Function
CD-545 flexible
CD-546 flexible
CH-168
(included in SY-001)
SW-001
SY-001
(including CP-201
(CH-168 board))
CCD IMAGER
CCD IMAGER
CCD SIGNAL PROCESS
CONTROL SWITCH
CAMERA MODULE, CAMERA DSP, CPU,
LENS DRIVE, BURST FLASH, SDRAM, AND FLASH,
LCD DRIVE, AUDIO, VIDEO, DC/DC CONVERTER,
FLASH DRIVE, CONNECTOR
DSC-W5/W7/W15/W17
2-8E
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/2)
OVERALL BLOCK DIAGRAM (2/2)
DSC-W5/W7/W15/W17
POWER BLOCK DIAGRAM
3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/2)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
SY-001 BOARD (1/2)
CD-545/546 FLEXIBLE BOARD (1/2)
CD-545 : W5/W15
CD-546 : W7/W17
CN201
(1/2)
Q103
BUFFER
CCD OUT
16
6
22
ı
35
134 136 2 4
6 9 12 15
18 21 24
27 30 32
86
Q101
CA AD00 – CA AD13
K5 G4 H4
L5 H2 H1
J1 J2 M5
J4 K4 M6
K2 K1
E9
B8
D9
19
SHUTTER
MOTOR
ZOOM
MOTOR
FOCUS
MOTOR
M
M
M
Q102
CCD
IMAGER
IRIS
MOTOR
M
30
31
1
3
7
6
7
5
133
4
10
7
5
2
4
9
6
V2, V4, V5A, V5B,
V6, V7A, V7B, V8
W7/W17 34
W5/W15 V2, V4, V5A, V5B, 30
V7, V8, V9, V10 ı
28
26
ı
W5/W15 W7/W17 23
36
V1, VST,
V1A, V1B,
V3B, V3A 35
V3A, V3B
33
32
V6
VHLD
27
VHLD
VST
31
VSUB
21
1
3
33
IC101
42
51 CCD SIGNAL
PROCESSOR,
37
TIMING
48 GENERATOR
RG, H1B, H2B
H1A, H2A
4
8
ı
10
12
ı
15
1
3
5
6
37
23
25
24
28
29
FOCUS
SENSOR
POWER SAVE
19
11
W5/ W7/ 26
W15 W17
27
9
12
ı
18
Q201
VSUB CONT
113 109
112 115
125 119
118 121
7
8
10
11
20
19
21
10
13
17
20
7
11
19
36
135
49
105
45
66
101
120
46
99
48
132
124
38
39
84
CA HD
MCK TG
40
41
3
123
42
CLKTGO
U22
Y25
E1
CN451 (1/2)
8
7
F MOTOR A, A, B, B
Z DC MOTOR ±
IRIS M±, S±
SHUTTER ±
F PI SENS OUT
BL L
BL H
U2
R6
VSUB CONT
LENS DRIVE
(3/9)
24
ı
27
FOCUS A, A, B, B
17
ı
20
ZOOM DC ±
5
ı
8
IRIS M±, S±
1
ı
4
SHUTTER±
A6
B5
A4
B4
FOCUS
MOTOR
DRIVER
B7
B8
C7
C8
C1
D2
ZOOM
MOTOR
DRIVER
B3
B1
A2
XSAN RST OUT
SAN1 SO, XSAN1 SCK
G5
H6
G4
H4
IRIS
MOTOR
DRIVER
G3
H2
G2
G1
E7
D7
SHUTTER
MOTOR
DRIVER
F8
F7
FC BRK A,
FC DIR A,
FC DIR B
L4
L2
N5
N2
P5
N6
4
1
VIDEO AMP
(7/9)
2
OVERALL (2/2)
(PAGE 3-3)
V LINE OUT
2
SAN AUOUT
SAN AUIN
XAUDIO MUTE
XCS AUDIO
AC1
AD1
T5
USB DP, USB DM
USB DPULLUP
DPULLUP ON
Q301
IRIS M IN,
IRIS M EN,
IRIS S IN,
IRIS S EN
P4
N4
P6
R2
AB6 AC4
AE4 AE5
AC5 AF6
MS BS, MS D0 – MS D3, MS CLK
XSAN RST OUT
MSHUT DIR,
MSHUT EN
R25
R5
FC SENS
U4
V4
ZM SENS 1ST
ZM DC FG 1A, 1B
LENS TEMP
31
SAN VOUT
VIDEO AMP ON
AB13 AA13 AE13 AF13
AF12 AE12 AA12 AC12
AC11 AB12 AE11 AF11
AE10 AB11 AC10 AB10
AF21 AF20 AE20 AB18 AB19 AC19 AB16
AE19 AF19 AF18 AE18 AA15 AC18 AC17
AB15 AE17 AF17 AE16 AB14 AC16 AC15 AE14
CPU D0 – CPU D15
V5
W4
CPU A01 – CPU A21, CPU A25
J25
XCPU CS4
K10
F4 K3 J3 G3 H7 H9 G6 G9
F7 E8 D10 D9
H8 H10 G8 G10
E7 E9 D7 E10
IC381
E8 D8 C8 B8 A8 B7 A7 F7 E6 E5 G5 B5
C7 A2 B2 C2 A1 B1 C1 E4 G3 E3 G1
D2 D1 D4 B6 A6 C6 B3 G7 F6 F5 F4
D5 F3 F2 E2
32M AND FLASH
(5/9)
XCPU CS0
SAN 27M CLKO
AE6
AF9
T851
E7
B4
IC351
32M BURST FLASH
(4/9)
D851
5
4
ST UNREG
1
3
TRIG 300V
1
2
XE_L
Q851
CHARGE+
6
IC851
TRANS DRIVE,
FLASH CONTROL,
FLASH CHARGE
DETECT
(9/9)
8
7
4
5
STRB CHG
XSTRB FULL
STRB ON
STRB CHG CONT
R22
V23
R4
AB22
D21 D22 D20 B22 A22 A23
B23 E20 E21 B24 A24 A25
B25 C25 C26 B26 E10 A10
D10 E11 B10 A11 B11 E12
D11 D12 F12 B12 A12 E13
D13 D14 F13 B15 F14 E14
D17 D18 D16 B18 A19
B19 E16 D19 E19 E17
B20 A20 B21 A21
A18
A17
DSP DQ00 – DSP DQ31, DSP DQM0 – DSP DQM3
DSP AQ00 – DSP AQ11, DSP QBA0, DSP QBA1
DSP QCLK
DSP QCLKE
R8 N7 R9 N8 P9 M8
M7 L8 L2 M3 M2 P1
N2 R1 N3 R2 E8 D7
D8 B9 C8 A9 C7 A8
A2 C3 A1 C2 B1 D2
D3 E2 K9 K1 F8 F2
G8 G9 F7 F3 G1
G2 G3 H1 H2 J3
G7 H9 J7 H8
J1
J2
CHARGE05
DSC-W5/W7/W15/W17
3-1
OVERALL (2/2)
(PAGE 3-4)
SAN1 SO, XSAN1 SCK
K26
L26
T23
Y26
AC6
A : VIDEO SIGNAL
A : AUDIO SIGNAL
A : VIDEO/AUDIO SIGNAL
1
IC802
R23
H26
U23
ZM BRK A,
ZM BRK B,
ZM DIR A
10
13
LENS TEMP
XE_H
D901
BACKLIGHT
SW-001 BOARD (1/2)
AF4
21
Z BOX1 PI SENS Col,
Z BOX2 PI SENS Col
C901
CHARGING +
CAPACITOR
8
7
XSAN RST OUT
29
Z PI SENS OUT
FLASH
UNIT
BL H
BL L
CN452
BL H
1
BL L
3
20
CN401
LENS TEMP
SENSOR
COLOR
LCD
MONITOR
SAN1 SO, XSAN1 SCK
IC401
ZOOM
SENSOR
CN752 (1/2)
IC301
(1/2)
CAMERA DSP, CPU
LENS CONTROL,
MODE CONTROL
(2/9)
W7/W17
Q202
ZOOM
FG
RGT, PSIG, 2
HCK1, HCK2, REF, 6
HST, PCG, XSTBY, ı
8
DWN, EN, VCK, VST 11
ı
14
19
ı
22
B1 K4 C2
D2 J4 D1
E2 F2 F1
G2 G1 H2
LCD901
F2
W5/W15
54MHz
LCD DRIVE
(6/9)
B9
A10
SAN1 SO, XSAN1 SCK
J6
IC601
B10
C10
J5
XCS FE, XCS TG
X201
67.5MHz
126
ı
129
H5
CA FD
47
XCS PANEL
XSAN RST OUT
W25
K2
K3
K1
CPU D0 – CPU D15
IC101
A9
C9
A2
LCD HD, LCD VD, LCD CK
CN601
R
4
G
5
B
3
CS, COM 23
24
CPU A01 – CPU A21
17
CH-168 BOARD
B3 A3
B4 B5
A5 B6
A7 B7
LCD D0 – LCD D7
CPU D0 – CPU D15
IRIS
(METER)
LENS
D8 D7
E8 E7
D6 D5
E6 B4
CPU A20, A21, A25
LENS BLOCK
PANEL UNIT
CP201
CAMERA MODULE
(1/9)
3-2
IC353
256M SDRAM
(4/9)
3-2. OVERALL BLOCK DIAGRAM (2/2)
SY-001 BOARD (2/2)
V LINE OUT
CN801
MIC SIG
B6
SAN AUOUT
SAN AUIN
E5
E6
F3
E3
SAN1 SO, XSAN1 SCK
XAUDIO MUTE
XCS AUDIO
OVERALL (1/2)
(PAGE 3-2)
CN802
IC801
AUDIO AMP
(7/9)
A5
A2
1
2
SP±
F1
E4
SP901
SPEAKER
J751
XAV JACK IN
V LINE OUT
AV OUT
(MONO)
AU LINE OUT
D1
2
MIC901
2
CN751
USB DP, USB DM
3
2
D±
DPULLUP ON
VCC
(USB)
1
CN705
MS BS, MS D0 – MS D3, MS CLK
MS BS, DATA0 – DATA3, SCLK
INT
2
ı
5
7
8
MEMORY
STICK
6
CD-545/546 FLEXIBLE
BOARD (2/2)
X301
12MHz
A6
U25
CD-545 : W5/W15
CD-546 : W7/W17
XAV JACK IN
XMS IN
USB VBUS
CN201
(2/2)
B10
C9
XAF LED
A4
SW-001 BOARD (2/2)
CN451
(2/2)
D456
(MS ACCESS)
1
1
CN752
(2/2)
XACCESS LED
D703
(AE/AF LOCK)
XAE LOCK LED
D702
FLASH/
RECORDING
XSTRB LED
XACCESS LED
F22
E22
X001
32.768kHz
IC301
(2/2)
5
5
KEY AD0
KEY AD0
K23
S451 – 453,
455, 459
FUNCTION
KEY
6
6
KEY AD1
KEY AD1
L23
IC001
DC/DC
CONVERTER
(8/9)
PANEL 8.5V
EVER 3.0V
MS VCCV
D 3.1V
A 3.1V
CAM 2.9V
D 1.8V
CAM –7.5V/–8.0V
CAM 15V
M 5V
D 1.2V
S456 – 458,
454, 460
FUNCTION
KEY
A8
XAF LED
D104
SELF TIMER/
AF ILLUMINATOR
A9
FRONT CONTROL
(2/9)
E4
39
CN001
ST UNREG
1
ı
7
BATT UNREG
10
ı
16
BATT GND
+
−
BT901
BATTERY
TERMINAL
CAM –0.5V
W7/W17
CONTROL SWITCH BLOCK
S001
(SHUTTER)
BT701
LITHIUM
BATTERY
H1
CN753
XAE LOCK ON
9
XSHTR ON
8
7 MODE DIAL0, 1
10
MODE
DIAL
B8
D001
(POWER)
5
S002
POWER
1
XPWR LED
XPWR ON
XAE LOCK SW
XSHUTTER SW
MODE DIAL0, 1
N21
P23
K25
T25
W23
L22
L25
AA5
AB5
Y5
D23
R26
Y4
AA23
BATT SENS
MS PWR ON
XCS DD
G5
D3
A6
C6
C5
B6
SAN0 SI, SAN0 SO, XSAN0 SCK
XDD RST OUT
A7
XPWR OFF
B7
XPWR ON
E9
F9
BL H
BL L
A : VIDEO SIGNAL
A : AUDIO SIGNAL
A : VIDEO/AUDIO SIGNAL
C7
05
DSC-W5/W7/W15/W17
3-3
1
OVERALL (1/2)
(PAGE 3-2)
3-4
3-3. POWER BLOCK DIAGRAM
SY-001 BOARD
T851
F001
FLASH
UNIT
UNREG
BT901
BATTERY
TERMINAL
CN001
SUFFIX:
-12, -22
L005
+
1
ı
7
−
10 BATT GND
ı
16
J1
K1
J6
K6
A1
B1
C2
D10
BT701
LITHIUM
BATTERY
VL 3V
D002
UNREG1-1
UNREG1-2
UNREG2-1
UNREG2-2
IC601
L604
LCD DRIVE
(6/9)
18
BL H
BL L
CN452
BL H
BL L
8
7
1
3
D 3.1V
VO1-1 F1
VO1-2 F2
VFB1 H2
L001
A 3.1V
D702
FLASH/
RECORDING
H1 LDO1
IC351
LDO2IN B3
LDO2 A3
D 1.8V
LDO3IN B2
LDO3 A2
CAM 2.9V
D703
(AE/AF LOCK)
32M BURST
FLASH
(4/9)
CN753
D 3.1V
D 3.1V
3
CAMERA MODULE
(1/9)
32M AND FLASH
(5/9)
CH-168 BOARD
L204
CAM 2.9V
53
DC CONTROL
(8/9)
CAM –0.5V
IC001
DC/DC
CONVERTER
(8/9)
4 IN–
3 IN+
L351
IC002
OUT 1
L203
Q005
IC353
DC CONTROL
256M SDRAM
(4/9)
54
55
71
L202
56
49
REG2 3
CAM –7.5V/–8.0V
FB203
2 VCC
51
W7/W17
STB 6
L006
CAM –0.5V
CAM 15V
REG1 1
50
W5/W15
SD 3.1V
D003
A 3.1V
REG
(8/9)
D 3.1V
IC003
D 1.2V
EVER 3.0V
4 VEE
SWITCHING
J9
J10
K9
K10
CD-545/546 FLEXIBLE BOARD
VO5 H10
VFB5 H9
CD-545 : W5/W15
CD-546 : W7/W17
L201
CAM 15V
GT6 H6
VFB6 H7
L010
P25
E5
XDD RST OUT
XPWR OFF
38
D104
SELF TIMER/
AF ILLUMINATOR
D 3.1V
MS VCC
MS VCC
D 3.1V
R26
Y4
AA23
SAN0 SI, SAN0 SO, XSAN0 SCK
IC101
CCD IMAGER
1
1
A 3.1V
M 5V
Q002, 003
M 5V
SWITCHING
1 CAM –7.5V : W5/W15
CAM –8.0V : W7/W17
IC401
LENS DRIVE
(3/9)
Q001
BG4 G9
CAM 15V
FB205
D 3.1V
L008
C6 SO
C5 SI
B6 SCLK
CN201
13
CAM –7.5V–8.0V
D3 MS PWR ON MS PWR IN G1
MS PWR G2
G5 UNREGMON
A6 CE
CCD SIGNAL
PROCESSOR,
TIMING
GENERATOR
FB204
Q004
PWR56OUT1 J7
PWR56OUT2 K7
IC101
52
57
L205
W7/W17
IC301
D 3.1V
IC381
D 1.2V
LX2 C10
VFB2 D8
FRONT
CONTROL
AA5
(2/9)
AB5
Y5
D001
(POWER)
4
CP201
L003
MS PWR ON
BATT SENS
XCS DD
BL H
BL L
D456
(MS ACCESS)
2
D001
T25
K25
W23
CN705
VCC
9
MEMORY
STICK
DC CONTROL
IC801
TG4 F10
PSG4 G8
VFB4 F7
A7 XRESET
AUDIO AMP
(7/9)
B7 XPWROFF
1 Vout
Vdd 4
A 3.1V
L802
LENS BLOCK
IC802
Q401
VIDEO AMP
(7/9)
D 3.1V
CN401
28
F PI SENS Vcc
ZOOM
FOCUS
SENSOR
Z PI SENS Vcc
ZOOM
SENSOR
IC804
2.8V REG
(7/9)
–7.5V ON
XFC RST LED
AU 3.1V
D 1.2V
XFC RST LED
23
AU 3.1V
D 1.2V
D 3.1V
L302
A 3.1V
D 3.1V
A 3.1V
D 3.1V
SD 3.1V
VI 3.1V
SD 3.1V
VI 3.1V
L301
05
DSC-W5/W7/W15/W17
3-5
COLOR
LCD
MONITOR
D901
BACKLIGHT
CN451
2
PANEL 8.5V
VO7 K4
LX5-1
LX5-2
LX5-3
LX5-4
VDD
SW-001 BOARD
CN752
BL H
8
BL L
7
D 3.1V
B8 RTCBAT
LCD901
CN601
M 5V
VO3 E9
VL3 F9
PWR1-1
PWR1-2
PWR1-3
PWR2
PANEL UNIT
L601
L602
PANEL 8.5V
TRANS DRIVE,
FLASH CONTROL,
FLASH CHARGE DETECT
(9/9)
SUFFIX:
-11, -21
LX3 E10
F002
BATT UNREG
CAM 2.9V
IC851
F003
L603
M 5V
L851
ST UNREG
3-6E
14
9
Z BOX2 PI
SENS Vcc
Z BOX1 PI
SENS Vcc
ZOOM
FG
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM
1
2
3
4
5
6
7
9
8
10
11
12
14
13
15
16
CONTROL
SWITCH
BLOCK
A
BT901
BATTERY
TERMINAL
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
10
9
8
7
6
5
4
3
2
1
BATT_GND
BATT_GND
BATT_GND
BATT_GND
BATT_GND
NC
NC
BATT_UNREG
BATT_UNREG
BATT_UNREG
BATT_UNREG
BATT_UNREG
BATT_UNREG
BATT_UNREG
MODE_DIAL1
XAE_LOCK_ON
XSHTR_ON
MODE_DIAL0
REG_GND
XPWR_LED
D_3.1V
D_3.1V
N.C.
XPWR_ON
CN753
10P
16
BATT_GND
16P
CN001
BATT_GND
B
Note: Pin name A/B of CN201
A : W5/W15
B : W7/W17
CN201
39P
XAF_LED
39
D_3.1V
38
C
FLASH
UNIT
GND
37
V1A/V1
36
V1B/VST
35
V2
34
V3A/V3B
33
V3B/V3A
32
VST/VHLD
31
V4
30
V5A
29
V5B
28
VHLD/V6
27
V6/V7
26
V7A/V8
25
V7B/V9
24
V8/V10
23
GND
22
D
C901
CN801 2P
MIC901
1
MIC_GND
2
MIC_SIG
CHARGING
CAPACITOR
MIC
SY-001 BOARD
E
CN752
CN451 8P
BL_H
8
8
BL_H
BL_L
7
7
BL_L
KEY_AD1
6
6
KEY_AD1
KEY_AD0
5
5
KEY_AD0
N.C
4
4
N.C.
REG_GND
3
3
REG_GND
D_3.1V
2
2
D_3.1V
XACCESS_LED
1
1
XACCESS_LED
F
FFC-051
FLEXIBLE
FLAT CABLE
SW-001
BOARD
CN705
(CONTROL SWITCH)
G
8P
(1/9) (CAMERA MODULE)
(2/9) (CAMERA DSP, CPU)
(3/9) (LENS DRIVE)
(4/9) (BURST FLASH, SDRAM)
(5/9) (AND FLASH)
(6/9) (LCD DRIVE)
(7/9) (AUDIO, VIDEO)
(8/9) (DC/DC CONVERTER)
(9/9) (FLASH DRIVE, CONNECTOR)
10P
VSUB
21
VSUB_CONT
20
POWER_SAVE
19
CCD_GND
18
NC
17
CCD_OUT
16
GND
15
GND
14
CAM_15V
13
GND
12
GND
11
H1B
10
H1A
9
GND
8
H2B
7
1
VSS
H2A
6
2
MS_BS
GND
5
3
DATA1
RG
4
4
SDIO/DATA0
GND
3
5
DATA2
GND
2
CAM_-7.5V/-8.0V
1
MEMORY
STICK
W5/W15
CD-545
FLEXIBLE
BOARD
(CCD IMAGER)
W7/W17
CD-546
FLEXIBLE
BOARD
LENS BLOCK
(CCD IMAGER)
OVF
CCD
DATA3
CN401
LENS_TEMP
31
GND
30
F_PI_SENS_OUT
29
F_PI_SENS_VCC
28
F_MOTOR_B
27
F_MOTOR_A
26
F_MOTOR_B
25
F_MOTOR_A
24
Z_PI_SENS_VCC
23
GND (Z_PI_SENS)
22
Z_PI_SENS_OUT
21
Z_DC_MOTER_-
20
8
SCLK
VCC
10
VSS
CP201
CH-168
BOARD
CN601 24P
COM
23
CS
22
VST
21
VCK
20
EN
19
DWN
Z_DC_MOTER_-
19
18
VDD
Z_DC_MOTER_+
18
VSS
Z_DC_MOTER_+
17
16
N.C.
GND (Z_BOX2)
16
15
VSSG
Z_BOX2_PI_SENS_OUT
15
14
XSTBY
Z_BOX2_PI_SENS_VCC
14
13
PCG
Z_BOX2_PI_SENS_Col
13
12
HST
Z_BOX1_PI_SENS_OUT
12
11
REF
GND (Z_BOX1)
11
10
TEST1
Z_BOX1_PI_SENS_Col
10
9
N.C.
Z_BOX1_PI_SENS_Vcc
9
8
HCK2
IRIS_M_-
8
HCK1
6
PSIG
5
G
4
R
3
2
RGT
TEST2
1
2
4
SP-
B
2
3
1
J751
AV OUT
(MONO)
2P
K
BT701
LITHIUM
BATTERY
SP+
7
CCD SIGNAL
PROCESS
CN802
17
LCD901
2.5 INCH
COLOR
LCD MONITOR
31P
24
1
D901
BACKLIGHT
J
INT
7
9
BL_H
N.C.
BL_L
N.C.
PANEL UNIT
I
6
1
2
3
4
N.C.
N.C.
6
H
5
CN452
6P
MEMORY STICK
IRIS_M_+
7
CN751 5P
IRIS_S_-
6
5
GND
IRIS_S_+
5
4
ID
SHUTTER_-
4
3
D+
SHUTTER_-
3
2
D-
SHUTTER_+
2
1
VCC
SHUTTER_+
1
(USB)
LENS FLEXIBLE
L
SP901
SPEAKER
05
DSC-W5/W7/W15/W17
4-1
4-2
FRAME
4-2. SCHEMATIC DIAGRAMS
Link
CD-545 FLEXIBLE BOARD: W5/W15
(CCD IMAGER)
SW-001 BOARD (CONTROL SWITCH)
(CCD IMAGER)
CONTROL SWITCH BLCOK
COMMON NOTE FOR SCHEMATIC DIAGRAMS
DSC-W5/W7/W15/W17
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
(For schematic diagrams)
• All capacitors are in µF unless otherwise noted. pF : µ
Link
µF. 50 V or less are not indicated except for electrolytics
and tantalums.
• Chip resistors are 1/10 W unless otherwise noted.
kΩ=1000 Ω, MΩ=1000 kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520
1. Connection
Pattern box
Color bar chart
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
For PTB-450:
J-6020-250-A
For PTB-1450:
J-6082-559-A
L = About 28 cm(PTB-450)
Pattern box
L = About 12 cm(PTB-1450)
L
Kinds of capacitor
Case Size
External dimensions (mm)
Front of the lens
• Constants of resistors, capacitors, ICs and etc with XX
indicate that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with ★ differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic
curve B, unless otherwise noted.
• Signal name
XEDIT → EDIT
PB/XREC → PB/REC
• 2: non flammable resistor
• 5: fusible resistor
• C: panel designation
• A: B+ Line
• B: B– Line
• J : IN/OUT direction of (+,−) B LINE.
• C: adjustment for repair.
• A: not use circuit
• Circled numbers refer to waveforms.
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the
measurement points and ground when camera shoots
color bar chart of pattern box. They are reference values
and reference waveforms.
(VOM of DC 10 MΩ input impedance is used)
• Voltage values change depending upon input
impedance of VOM used.)
2. Adjust the distance so that the output waveform of
Fig. a and the Fig. b can be obtain.
Blue
Yellow
Cyan
Green
White
Magenta
Red
H
B
B
A
A
A=B/2
Fig. a (Video output terminal output waveform)
Electronic beam
scanning frame
CRT picture frame
Fig.b (Picture on monitor TV)
When indicating parts by reference number, please
include the board name.
Note :
Note :
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
DSC-W5/W7/W15/W17
4-5
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifie.
For Schematic Diagram
• Refer to page 4-37 for printed wiring board.
3
5
4
CD-545 FLEXIBLE BOARD : W5/W15
CCD IMAGER (5M CCD BLOCK)
Note: Voltage and Waveform of mounted on CD-545 flexible
board can not be measured, because they are mounted
by the side of the lens.
XX MARK:NO MOUNT
24
V7B
LND117
23
V8
LND118
22
GND
LND119
21
VSUB
LND120
20
VSUB_CONT
LND121
19
POWER_SAVE
LND122
18
CCD_GND
LND123
17
NC
LND124
16
CCD_OUT
LND125
15
GND
LND126
14
GND
LND127
13
CAM_15V
LND128
12
GND
LND129
11
GND
LND130
10
H1B
LND131
9
H1A
LND132
8
GND
LND133
7
H2B
LND134
6
H2A
LND135
5
GND
LND136
4
RG
LND137
3
GND
LND138
2
GND
LND139
1
CAM_-7.5V
C101
XX
Q101
DTC144EMT2L
SWITCH
16 15 14 13 12 11 10
R102
22k
R103
3900
9
8
7
6
5
4
3
2
1
NC
LND116
V1A
V7A
NC
V6
25
H2A
26
LND115
V2
LND114
V1B
VHLD
H1A
V5B
27
V3A
28
LND113
VL
LND112
V3B
V5A
NC
29
CSUB
V4
LND111
V4
30
VST
VST
LND110
IC101
R101
82
CCD IMAGER
IC101
ICX455CQZ-13
Q103
2SC4250(T5LSONY1)
BUFFER
SUB
V3B
31
V5A
32
LND109
H1B
LND108
V5B
V3A
H2B
33
RG
V2
LND107
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
C103
XX
16V
34
0.1u
V1B
LND106
V6
35
VHLD
V1A
LND105
V7A
36
R109
0
C107
F
GND
LND104
VDD
E
D_3.1V
37
GND
CN201
PAGE 4-13
of LEVEL3
38
LND103
GND
SY-001
(1/9)
LND102
D104
OPY5052
SELF TIMER/
AF ILLUMINATOR
V8
D
XAF_LED
NC
C
39
VOUT
B
LND101
8
Note: CD-545 flexible complete board and IC101 are not supplied,
but there are included in CCD block assy.
V7B
A
7
6
GND
2
NC
1
R104
820
G
Q102
DTC144EMT2L
SWITCH
C102
0.1u
16V
C104
0.1u
16V
R105
3900
05
C105
0.1u
16V
Precautions for Replacement of CCD Imager
• The CD-545 flexible board mounted as a repair part is not
equipped with a CCD imager.
When replacing this board, remove the CCD imager from the
old one and mount it onto the new one.
• If the CCD imager has been replaced, carry out all the
adjustments for the camera section.
• As the CCD imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with dusts
nor exposed to strong light.
DSC-W5/W7/W15/W17
4-7
4-8
CD-545
3
2
4
6
5
CD-546 FLEXIBLE BOARD : W7/W17
CCD IMAGER (7M CCD BLOCK)
Note: Voltage and Waveform of mounted on CD-546 flexible
board can not be measured, because they are mounted
by the side of the lens.
XX MARK:NO MOUNT
26
V7
LND115
25
V8
LND116
24
V9
LND117
23
V10
LND118
22
GND
LND119
21
VSUB
LND120
20
VSUB_CONT
LND121
19
POWER_SAVE
LND122
18
CCD_GND
LND123
17
NC
LND124
16
CCD_OUT
LND125
15
GND
LND126
14
GND
LND127
13
CAM_15V
LND128
12
GND
LND129
11
GND
LND130
10
H1B
C101
XX
H1A
8
GND
LND133
7
H2B
LND134
6
H2A
LND135
5
GND
LND136
4
RG
LND137
3
GND
LND138
2
GND
LND139
1
CAM_-8.0V
C103
XX
V6
V5B
V7
7
6
5
4
3
2
1
IC101
R103
2700
CCD IMAGER
IC101
ICX489CQZ-13
RG
R102
12k
8
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Q103
2SC4250(T5LSONY1)
BUFFER
16V
9
LND132
R101
33
9
R109
0
0.1u
LND131
Q101
DTC144EMT2L
SWITCH
V8
16 15 14 13 12 11 10
V1
V6
LND114
NC
V5B
27
NC
28
LND113
GND
LND112
V2
V5A
VST
V4
29
VL
30
LND111
H2A
LND110
V3A
VHLD
VHLD
V3A
31
H1A
32
LND109
CSUB
LND108
V4
V3B
V3B
V2
33
SUB
34
LND107
H1B
LND106
V5A
VST
H2B
35
C107
F
V1
LND105
VDD
E
36
GND
PAGE 4-13
of LEVEL3
GND
LND104
V9
CN201
37
GND
SY-001
(1/9)
D_3.1V
LND103
GND
D
XAF_LED
38
NC
C
39
LND102
VOUT
B
LND101
D104
OPY5052
SELF TIMER/
AF ILLUMINATOR
V10
A
8
7
Note: CD-546 flexible complete board and IC101 are not supplied,
but there are included in CCD block assy.
NC
1
R104
1200
G
Q102
DTC144EMT2L
SWITCH
05
C104
XX
16V
R105
1500
C102
0.1u
16V
C105
0.1u
16V
Precautions for Replacement of CCD Imager
• The CD-546 flexible board mounted as a repair part is not
equipped with a CCD imager.
When replacing this board, remove the CCD imager from the
old one and mount it onto the new one.
• If the CCD imager has been replaced, carry out all the
adjustments for the camera section.
• As the CCD imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with dusts
nor exposed to strong light.
DSC-W5/W7/W15/W17
4-9
4-10
CD-546
Schematic diagrams of the CH-168 and SY-001 boards are not shown.
Pages from 4-11 to 4-30 are not shown.
DSC-W5/W7/W15/W17
1
2
4
3
5
6
SW-001 BOARD
2
B
(ZOOM)
R456
2200
1
S459
W
LND452
2
1
4
3
R007
6800
STATIC_GND
B
LND451
DISPLAY/
LCD ON/OFF
2
1
4
3
C
R452
2200
2
S456
2
1
4
3
D453
XX
3
D455
XX
R455
2200
4
D451
MAZS068008SO
S451
D452
MAZS068008SO
STATIC_GND
CN452
N.C.
5
N.C.
4
N.C.
3
BL_L
2
N.C.
1
R004
22k
6P
6
D901
BACKLIGHT
11
Beach
12
Landscape
C
9
Snow
Candle
8
Twilight
portrait
7
Twilight
6
MANUAL
5
P_AUTO
4
AUTO
R012
2200
BL_H
R013
6800
Soft
snap
1
2
MOVIE
3
PLAY
2
2
1
R451
2200
4
3
S454
1
(1st)
2
1
4
3
S457
4
3
S460
(SET)
(MACRO)
CN451 8P
R458
2200
4
3
S453
IMAGE SIZE/
DELETE
R011
4700
S001
(SHUTTER)
1
(REVIEW)
R008
3300
R006
2200
R457
2200
R454
2200
E
10
1
(SELF TIMER)
2
R010
3300
R009
4700
R014
22k
4
3
S452
MENU
D
4
CONTROL SWITCH BLOCK is replaced as block,
so that PRINTED WIRING BOARD is omitted.
XX MARK:NO MOUNT
S455
T
3
A
CONTROL SWITCH
2
8
BL_H
7
BL_L
6
KEY_AD1
5
KEY_AD0
4
N.C.
3
2
R459 1k
1
R453
2200
D456
SML-310LTT86
(MS ACCESS)
4
3
S458
REG_GND
2
D_3.1V
1
XACCESS_LED
D
(2nd)
SY-001
(8/9)
CN752
THROUGH THE
FFC-051 FLEXIBLE
FLAT CABLE
3
1
4
2
S002
POWER
PAGE 4-28
of LEVEL3
R016
20k
E
R015
20k
(FLASH)
05
G
5 XPWR_LED
4 D_3.1V
3 D_3.1V
2 N.C.
1 XPWR_ON
LND004
LND003
LND002
LND001
7 MODE_DIAL0
6 REG_GND
8 XSHTR_ON
LND007
LND005
9 XAE_LOCK_ON
LND008
LND006
10 MODE_DIAL1
LND010
LND009
F
D001
TLYU1002(TPX1,SONY)
(POWER)
A
1
SY-001
(9/9)
CN753
PAGE 4-29
of LEVEL3
05
DSC-W5/W7/W15/W17
4-31
4-32
SW-001, CONTROL SWITCH BLOCK
4-3. PRINTED WIRING BOARDS
Link
SW-001 BOARD
COMMON NOTE FOR PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
Board Name
CIRCUIT BOARDS LOCATION
Function
CD-545 FLEXIBLE CCD IMAGER
CD-546 FLEXIBLE CCD IMAGER
SW-001
CONTROL SWITCH
DSC-W5/W7/W15/W17
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS
•
•
•
•
•
•
: Uses unleaded solder.
: Circuit board
: Flexible board
Pattern from the side which enables seeing.
: pattern of the rear side
(The other layers’ patterns are not indicated)
Through hole is omitted.
Circled numbers refer to waveforms.
There are a few cases that the part printed on diagram
isn’t mounted in this model.
C: panel designation
Board Name
• Chip parts.
Transistor
B
Parts Location
Diode
6 5 4 4 5 6 5
C
E
4 4
3
1 23
2
1 2
1 2
1
4
3
3
4 6 5 4 4 5 6
2
1 1 2 3 3 2 1
2 2
1 3
2
5 4 3 3 4 5 4
1
(Shown on Page)
Total Number of Layers
Layers Not Indicated
CD-545 flexible
4-47
2 layers
–
CD-546 flexible
4-47
2 layers
–
SW-001
4-49
2 layers
–
4-35
3
1 2 3 3 2 1 1 2 3 3 2 1
Pattern
DSC-W5/W7/W15/W17
3
5
1
2
3
2
4
1
1 6 54
CD-545 FLEXIBLE: W5/W15
CD-546 FLEXIBLE: W7/W17
Note for Printed Wiring Board (See page 4-35).
7M
D104
SELF TIMER/
AF ILLUMINATOR
D104
5M
CD-546 FLEXIBLE BOARD
A
D104
SELF TIMER/
AF ILLUMINATOR
D104
A
Note: CD-545 flexible complete board and IC101
are not supplied, but there are included in
CCD block assy.
B
Note: CD-546 flexible complete board and IC101
are not supplied, but there are included in
CCD block assy.
B
CD-545
CD
C
DD-545
D-545
545 1
1-865-829865 829
>PI
>PI<
>P
PI<
I<
A
CD
C
CD-546
D-546
D
546 1
1-865-830865 830
>PI<
>P
>
PI
PI<
P
I<
I<
16 15 14
3
A
2
16 15 14
3 2
1
IC101
C
1
IC101
C
17
17
R102
R101
C101
R102
C107
C105
R101
C104
30 31 32
C107
C105
C104
R104
R104
R105
R105
C
B E
D
18 19
C
C102
R103
C103
B
E
R109
R109
Q103
30 31 32
18 19
Q101 BC E
C101
C103
C
C102
R103
B
E
Q101 B C E
Q103
C
B E
D
Q102
E
Q102
05
1
LND102
LND104
LND106
LND108
LND110
LND112
LND114
LND116
LND118
LND120
LND122
LND124
LND126
LND128
LND130
LND132
LND134
LND136
LND138
1-865-829- 11
39
1
2
05
LND101
LND103
LND105
LND107
LND109
LND111
LND113
LND115
LND117
LND119
LND121
LND123
LND125
LND127
LND129
LND131
LND133
LND135
LND137
LND139
39
LND101
LND102
LND103
LND104
LND105
LND106
LND107
LND108
LND109
LND110
LND111
LND113 LND112
LND114
LND115
LND116
LND117
LND118
LND119
LND120
LND121
LND122
LND123
LND124
LND125
LND126
LND127
LND128
LND129
LND130
LND131
LND132
LND133
LND134
LND135
LND136
LND137
LND138
LND139
E
1
1-865-830- 11
1
2
DSC-W5/W7/W15/W17
4-37
4-38
CD-545, CD-546
Printed wiring boards of the CH-168 and SW-001 boards are not shown.
Pages from 4-39 to 4-42 are not shown.
DSC-W5/W7/W15/W17
SW-001
SW-001 BOARD
1
3
1
3
S459
A
S455
2
4
2
4
S455
S459
T
W (ZOOM)
R456
CN452
6
S451
1
1
DISPLAY/
LCD ON/OFF
3
S451
CN451
D453
1
S452
LND451
D452
R452
B
8
4
R455
2
R451
MENU
3
S458
R459
1
S452
(FLASH)
2
4
1
3
C
S460
S454
2
4
S457
(MACRO)
(REVIEW)
1
3
1
S454
S453
2
4
1
3
IMAGE SIZE/
DELETE
D
3
S460
S456
2
R454
2
4
S456
(SELF TIMER)
4
R458
4
2
(SET)1
S457
2
4
3
D456
(MS ACCESS)
K
S453
R457
05
1
1-865-828-
11
21
2
DSC-W5/W7/W15/W17
4-43
D455
D451
A
1
LND452
3
D456
R453
S458
4-44
SW-001
Waveforms of the SW-001 board are not shown.
Pages 4-45 and 4-46 are not shown.
DSC-W5/W7/W15/W17
no mark : side A
* mark : side B
4-5. MOUNTED PARTS LOCATION
C101
C102
C103
C104
C105
C107
C-1
C-1
C-1
D-2
D-2
D-2
C101
C102
C103
C104
C105
C107
C-1
C-1
C-1
D-2
D-2
D-2
D104
A-1
D104
A-1
IC101
C-2
IC101
C-2
Q101
Q102
Q103
D-1
D-1
C-1
Q101
Q102
Q103
D-1
D-1
C-1
R101
R102
R103
R104
R105
R109
D-1
D-1
C-1
D-2
D-2
C-1
R101
R102
R103
R104
R105
R109
D-1
D-1
C-1
D-2
D-2
C-1
DSC-W5/W7/W15/W17
4-47
CD-545, CD-546
Mounted parts location of the SY-001 board is not shown.
Pages 4-48 is not shown.
DSC-W5/W7/W15/W17
no mark : side A
* mark : side B
SW-001 BOARD
CN451 B-2
CN452 A-2
D451
D452
D453
D455
D456
D-2
B-1
B-2
D-2
D-2
R451
R452
R453
R454
R455
R456
R457
R458
R459
B-1
B-1
C-1
D-1
B-1
A-1
D-2
D-2
C-2
S451
S452
S453
S454
S455
S456
S457
S458
S459
S460
B-1
B-1
D-1
C-1
A-2
D-1
C-1
C-1
A-1
C-2
DSC-W5/W7/W15/W17
4-49E
SW-001
NOTE
5. REPAIR PARTS LIST
NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
EXPLODED VIEWS
Link
A
OVERALL ASSEMBLY
Link
B
CABINET (FRONT) BLOCK
MAIN BLOCK ASSEMBLY
ELECTRICAL PARTS LIST
CD-545 FLEXIBLE BOARD D
DSC-W5/W7/W15/W17
C
D
D
LENS BLOCK ASSEMBLY
ACCESSORIES
SW-001 BOARD
A
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from
the original one.
• Items marked “*” are not stocked since they are seldom required for routine
service. Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not
supplied.
• Due to standardization, replacements in the parts list may be different from
the parts specified in the diagrams or the components used on the set.
• CAPACITORS:
uF: µF
• COILS
uH: µH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , µPC... , µPC... ,
uPD..., µPD...
• Abbreviation
CH : Chinese model
J
: Jpanese model
JE : Tourist model
KR : Korean model
DSC-W5/W7/W15/W17
5-1
When indicating parts by reference number,
please include the board name.
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
Ver 1.2 2005.09
5-1. EXPLODED VIEWS
5-1-1. OVERALL ASSEMBLY
ns: not supplied
4
3
1
ns
5
LCD901
2
Main block assembly
(See page 5-4.)
4
D901
6
7
8
9
7
ns
Cabinet (front) block
(See page 5-3.)
7
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Ref. No.
Part No.
Description
1
1
1
1
1
1-479-037-11
1-479-037-21
1-479-037-31
1-479-037-41
1-479-037-51
SWITCH BLOCK, CONTROL (SILVER) (W5)
SWITCH BLOCK, CONTROL (SILVER) (W7)
SWITCH BLOCK, CONTROL (BLACK) (W15)
1
02
3
4
5
6
1-479-037-61
2-348-199-01
A-1096-987-A
3-078-889-11
2-348-202-01
2-348-201-01
GUARD, TERMINAL
SW-001 BOARD, COMPLETE
SCREW (M1.7)
BLIND SHEET
FRAME, LCD
Ref. No.
Part No.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
Description
7
7
8
2-515-756-21 SCREW (M1.7), TORASUTA, P2 (SILVER)
2-515-756-71 SCREW (M1.7), TORASUTA, P2 (BLACK)
A-1095-193-A CABINET (REAR) BLOCK ASSY (W5: SILVER)
8
8
9
9
D901
A-1095-276-A
A-1095-278-A
2-580-522-01
2-580-522-11
1-479-015-11
CABINET (REAR) BLOCK ASSY (BLACK)
CABINET (REAR) BLOCK ASSY (W7: SILVER)
CABINET, BT SIDE (C) (SILVER)
CABINET, BT SIDE (C) (BLACK)
BLOCK, LIGHT GUIDE PLATE (2.5)
LCD901 8-753-229-36 ACX336AK-3
DSC-W5/W7/W15/W17
5-2
5-1-2. CABINET (FRONT) BLOCK
58
MIC901
57
60
59
61
SP901
55
56
54
53
52
62
63
66
64
67
65
51
Ref. No.
Part No.
Description
51
51
52
52
52
2-348-157-01
2-348-157-11
2-348-158-01
2-348-158-11
2-348-293-01
RING, LENS (W5/W7: SILVER/W15)
RING, LENS (W7: BLACK/W17)
GRIP (40) (W5: SILVER)
GRIP (40) (W5: BLACK/W15)
GRIP (50) (W7/W17)
53
54
55
55
55
2-515-716-01
3-348-998-51
2-348-156-01
2-348-156-11
2-348-156-21
56
57
58
59
60
2-348-161-01
2-348-166-01
2-348-185-01
2-348-198-01
2-108-698-01
Ref. No.
Part No.
Description
61
62
62
63
64
2-348-163-01
X-2024-644-1
X-2025-148-1
2-348-160-01
2-348-164-01
SCREW, TRIPOD
BOTTOM ASSY (40), CABINET (SILVER)
BOTTOM ASSY (B (40)), CABINET (BLACK)
INNER HOLDER (FRONT)
SHEET (OVF), ADHESIVE
SHEET, GRIP ADHESIVE
SCREW (M1.4X3.5), TAPPING, PAN
CABINET (FRONT) (W5: SILVER)
CABINET (FRONT) (BLACK)
CABINET (FRONT) (W7: SILVER)
65
65
66
66
67
2-348-162-01
2-348-162-11
2-515-756-21
2-515-756-71
2-348-159-01
WINDOW, OVF (SILVER)
WINDOW, OVF (BLACK)
SCREW (M1.7), TORASUTA, P2 (SILVER)
SCREW (M1.7), TORASUTA, P2 (BLACK)
RING (40), ORNAMENTAL (W5/W15)
WINDOW, AF
CUSHION, MICROPHONE
CUSHION, MICROPHONE (B)
COVER, MIC
SCREW (M1.4)
67
67
MIC901
SP901
2-348-294-01
2-348-294-11
1-542-600-11
1-825-923-21
RING (50), ORNAMENTAL (SILVER) (W7)
RING (50), ORNAMENTAL (BLACK) (W7/W17)
MICROPHONE UNIT
LOUDSPEAKER (1.3CM)
DSC-W5/W7/W15/W17
5-3
5-1-3. MAIN BLOCK ASSEMBLY
ns: not supplied
103
104
BT901
SY
-00
1
102
ns
(Note)
!
101
(including CP201
(CH-168 board)
and BT701)
BT701
Lens block assembly
(See page 5-5.)
! Board
BT701(BATTERY, LITHIUM SECONDARY)
on the mount position (See page 4-40).
105
C901
Note: Included in SY-001 board (suffix: -11).
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Ref. No.
101
101
101
101
101
101
101
101
Part No.
Description
Ref. No.
A-1096-995-A SY-001 BOARD, COMPLETE (SERVICE) (GP1)
(W5: J)
(W5: US, CND, AUS/W15: AUS)
(W7: J)
(W7: US, CND, AUS/W17: AUS)
(W5: AEP, UK/W15: AEP, UK)
(W5: AR, BR, E/W15: E)
(W5: CH, HK, KR, JE/W15: CH, HK, KR, JE)
(W7: AEP, UK/W17: AEP, UK)
101
Part No.
sécurité.
Description
0 102
103
104
(W7: AR, BR, E/W17: E)
(W7: CH, HK, KR, JE/W17: HK, KR, JE)
1-479-039-11 FLASH UNIT
1-963-591-11 CABLE, FLEXIBLE FLAT (FFC-051)
2-348-515-01 LABEL, FUSE REPLACEMENT CAUTION
0 105
0 105
0 BT701
0 BT901
X-2024-645-1
X-2025-151-1
1-528-999-61
1-756-527-11
101
0 BT901
0 BT901
0 C901
DSC-W5/W7/W15/W17
5-4
HOLDER ASSY (40), JACK (SILVER)
HOLDER ASSY (B (40)), JACK (BLACK)
BATTERY, LITHIUM SECONDARY
HOLDER, BATTERY (WITH TERMINAL)
(W5: SILVER)
1-756-527-21 HOLDER, BATTERY (WITH TERMINAL) (BLACK)
1-756-527-31 HOLDER, BATTERY (WITH TERMINAL)
(W7: SILVER)
1-112-169-11 CAP, ELECT
135uF
5-1-4. LENS BLOCK ASSEMBLY
161
(including CD-545/546 flexible board
and IC101) (Note 2)
159
160
158
157
162
156
151
155
154
(Note 1)
153
(Note 1)
152
(Note 1)
Note 1: Be sure to read “2-3. Exchange Method of Barrier Assy”
on page 2-5 when change Ref. No. 152, 153 and 154.
Note 2: Be sure to read “Precuations for Replacement of CCD
Imager” on page 4-8 or 4-10 when changing the CCD
imager.
Ref. No.
Part No.
Description
151
152
153
154
155
A-1105-719-A
3-091-427-01
3-086-156-31
X-3954-476-1
2-021-317-01
LENS BLOCK ASSY (890C (J1))
RING (A), ORNAMENTAL (Note 1)
SCREW, TAPPING (P2) (Note 1)
BARRIER ASSY (Note 1)
MASK, LPF
156
156
157
158
1-788-104-11
1-788-176-11
2-021-318-01
2-348-196-01
OPTICAL FILTER BLOCK (W5/W15)
OPTICAL FILTERBLOCK (OFB-02-21) (W7/W17)
SEALGOM 890
HOLDER, AF
Ref. No.
159
160
161
161
162
DSC-W5/W7/W15/W17
5-5
Part No.
Description
3-080-222-01 SCREW (M1.7), TAPPING, P2
3-348-998-61 SCREW (M1.4X4), TAPPING, PAN
A-1087-313-A CCD BLOCK ASSY
(including CD-545 flexible board and IC101
(CCD IMAGER)) (W5/W15) (Note 2)
A-1087-314-A CCD BLOCK ASSY
(including CD-546 flexible board and IC101
(CCD IMAGER)) (W7/W17) (Note 2)
X-2024-646-1 FRAME ASSY, LENS
CD-545
CD-546
5-2. ELECTRICAL PARTS LIST
Ref. No.
Part No.
Description
Ref. No.
A-1087-313-A CCD BLOCK ASSY (W5/W15)
(Not supplied) CD-545 FLEXIBLE BOARD, COMPLETE
*******************************
(CCD block assy is including CD-545 flexible board and IC101 (CCD
imager).)
Part No.
Description
R103
R104
R105
1-218-958-11 RES-CHIP
1-218-954-11 RES-CHIP
1-218-955-11 RES-CHIP
2.7K
1.2K
1.5K
R109
1-218-990-11 SHORT CHIP
0
5%
5%
5%
1/16W
1/16W
1/16W
< CAPACITOR >
C102
C104
C105
C107
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
Electrical parts list of the CH-168 board is
not shown.
Page 5-7 is not shown.
16V
16V
16V
16V
< DIODE >
D104
6-500-505-01 DIODE OPY5052
(SELF TIMER/AF ILLUMINATOR)
< IC >
IC101
(Not supplied) CCD IMAGER (Note)
< TRANSISTOR >
Q101
Q102
Q103
6-550-119-01 TRANSISTOR
DTC144EMT2L
DTC144EMT2L
2SC4250 (T5LSONY1)
< RESISTOR >
R101
R102
R103
R104
R105
1-218-940-11
1-218-969-11
1-218-960-11
1-218-952-11
1-218-960-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
R109
1-218-990-11 SHORT CHIP
82
22K
3.9K
820
3.9K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
0
A-1087-314-A CCD BLOCK ASSY (W7/W17)
(Not supplied) CD-546 FLEXIBLE BOARD, COMPLETE
*******************************
(CCD block assy is including CD-546 flexible board and IC101 (CCD
imager).)
< CAPACITOR >
C102
C105
C107
1-107-826-11 CERAMIC CHIP
0.1uF
0.1uF
0.1uF
10%
10%
10%
16V
16V
16V
< DIODE >
D104
6-500-505-01 DIODE OPY5052
(SELF TIMER/AF ILLUMINATOR)
< IC >
IC101
(Not supplied) CCD IMAGER (Note)
< TRANSISTOR >
Q101
Q102
Q103
DTC144EMT2L
DTC144EMT2L
2SC4250 (T5LSONY1)
< RESISTOR >
R101
R102
1-218-935-11 RES-CHIP
1-218-966-11 RES-CHIP
33
12K
5%
5%
1/16W
1/16W
DSC-W5/W7/W15/W17
5-6
Note: Be sure to read “Precautions for Replacement of
CCD Imager” on page 4-8 or 4-10 when changing
the CCD imager.
SW-001
Ref. No.
Part No.
Description
Ref. No.
A-1096-987-A SW-001 BOARD, COMPLETE
***********************
< CONNECTOR >
CN451
CN452
1-817-549-11 CONNECTOR, FPC (LIF (NON-ZIF)) 8P
1-816-654-31 FFC/FPC CONNECTOR (LIF) 6P
< DIODE >
D451
D452
D456
8-719-056-54 DIODE MAZS068008SO
8-719-056-54 DIODE MAZS068008SO
8-719-064-07 DIODE SML-310LTT86 (MS ACCESS)
< RESISTOR >
R451
R452
R453
R454
R455
1-216-825-11
1-216-825-11
1-216-825-11
1-216-825-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
2.2K
2.2K
2.2K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R456
R457
R458
R459
1-216-825-11
1-216-825-11
1-216-825-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
2.2K
2.2K
1K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
< SWITCH >
S451
S452
S453
S454
S455
1-786-157-11
1-786-157-11
1-786-157-11
1-786-157-11
1-786-157-11
SWITCH, TACTILE (DISPLAY / LCD ON/OFF)
SWITCH, TACTILE (MENU)
SWITCH, TACTILE (IMAGE SIZE/DELETE)
SWITCH, TACTILE (g(REVIEW))
SWITCH, TACTILE (T(ZOOM))
S456
S457
S458
S459
S460
1-786-157-11
1-786-157-11
1-786-157-11
1-786-157-11
1-786-157-11
SWITCH, TACTILE (F(SELF TIMER))
SWITCH, TACTILE (a(SET))
SWITCH, TACTILE (f(FLASH))
SWITCH, TACTILE (W(ZOOM))
SWITCH, TACTILE (G(MACRO))
Electrical parts list of the SY-001 board is not
shown.
Pages 5-9 to 5-12 are not shown.
DSC-W5/W7/W15/W17
5-8
Part No.
Description
Ver. 1.5 2007.09
The changed portions from
Ver. 1.4 are shown in blue.
Checking supplied accessories.
Note: This item is supplied with the unit as an accessory,
but is not prepared as a service part.
Battery charger
(BC-CS2A/CS2B) (1)
0 1-477-814-41 (US, CND, JE, J)
0 1-477-814-51 (AEP, UK, E, AR, HK, AUS)
0 1-477-814-61 (KR, CH)
A/V connecting cable (1)
1-824-519-11
Battery case (1)
3-074-757-01
USB cable (1)
1-827-038-11
Other accessories
HR6 (size AA)
Ni-MH batteries (2)
(Note)
Power cord (1)
0 1-823-946-12 (AEP, E)
0 1-782-476-51 (CH)
0 1-783-374-11 (UK, HK)
0 1-783-952-21 (AR)
0 1-790-107-42 (US, CND)
0 1-790-732-12 (JE, J)
0 1-776-985-12 (KR)
0 1-827-945-11 (AUS)
Conversion 2P adaptor (1)
0 1-569-008-21 (E)
Wrist strap (1)
2-050-981-01 (Silver)
2-050-981-11 (Black)
Conversion 2P adaptor (1)
0 1-569-007-12 (JE)
2-586-553-01 INSTRUCTION (READ THIS FIRST) (JAPANESE) (J)
2-586-553-11 INSTRUCTION (READ THIS FIRST) (ENGLISH)
(EXCEPT AR, KR, CH, J)
2-586-553-21 INSTRUCTION (READ THIS FIRST) (FRENCH, ITALIAN)
(AEP, CND)
2-586-553-31 INSTRUCTION (READ THIS FIRST) (SPANISH,
PORTUGUESE) (AEP, E, AR, JE)
2-586-553-41 INSTRUCTION (READ THIS FIRST) (GERMAN, DUTCH)
(AEP)
2-586-553-51 INSTRUCTION (READ THIS FIRST) (TRADITIONAL
CHINESE, SIMPLIFIED CHINESE) (E, HK, CH, JE)
2-586-553-61 INSTRUCTION (READ THIS FIRST) (RUSSIAN,
SWEDISH) (AEP)
2-586-553-71 INSTRUCTION (READ THIS FIRST) (ARABIC, PERSIAN)
(E)
2-586-553-81 INSTRUCTION (READ THIS FIRST) (KOREAN) (KR, JE)
2-586-553-91 INSTRUCTION (READ THIS FIRST) (POLISH, CZECH)
(AEP)
2-586-555-11 INSTRUCTION (READ THIS FIRST) (HUNGARIAN,
SLOVAK) (AEP)
2-586-561-01 INSTRUCTION (USER'S GUIDE) (JAPANESE) (J)
2-586-561-11 INSTRUCTION (USER'S GUIDE) (ENGLISH) (EXCEPT AR,
KR, CH, J)
2-586-561-21 INSTRUCTION (USER'S GUIDE) (FRENCH, ITALIAN) (AEP,
CND)
2-586-561-31 INSTRUCTION (USER'S GUIDE) (SPANISH,
PORTUGUESE) (AEP, E, AR, JE)
2-586-561-41 INSTRUCTION (USER'S GUIDE) (GERMAN, DUTCH)
Soft carrying case
(W15/W17 only) (1)
2-055-904-01
CD-ROM
(Cyber-shot application
software) (1)
2-583-852-31 (US, J)
2-583-853-01 (EXCEPT US, J)
(AEP)
2-586-561-51 INSTRUCTION (USER'S GUIDE) (TRADITIONAL CHINESE,
SIMPLIFIED CHINESE) (E, HK, CH, JE)
2-586-561-61 INSTRUCTION (USER'S GUIDE) (RUSSIAN, SWEDISH)
(AEP)
2-586-561-71 INSTRUCTION (USER'S GUIDE) (ARABIC, PERSIAN) (E)
2-586-561-81 INSTRUCTION (USER'S GUIDE) (KOREAN) (KR, JE)
2-586-561-91 INSTRUCTION (USER'S GUIDE) (POLISH, CZECH) (AEP)
2-586-563-11 INSTRUCTION (USER`S GUIDE) (HUNGARIAN, SLOVAK)
(AEP)
DSC-W5/W7/W15/W17
5-13E
5-9E
sécurité.
DSC-W5/W7/W15/W17
LEVEL
2
DSC-W5/W7
SERVICE MANUAL
US Model
Canadian Model
Argentine Model
Brazilian Model
Japanese Model
DSC-W5/W7/W15/W17
Ver 1.1 2005.07
AEP Model
UK Model
E Model
Australian Model
Hong Kong Model
Korea Model
Tourist Model
DSC-W5/W7/W15
Chinese Model
SUPPLEMENT-1
File this supplement with the service manual.
(PV05-033)
• Precaution on Replacing the SY-001 Board
1. SERVICE NOTE
1-7. PRECAUTION ON REPLACING THE SY-001 BOARD
When you replace to the repairing board, the written data of repairing board also might be changed to original setting.
When the data has changed because of board replaceing etc, check the data setting (VIDEO OUT Default Data, Exif Model Data) is right. If
not, rewrite to the right value.
VIDEO OUT Default Data
Page
Address
4F
4F
Data
8D
NTSC
00
PAL
01
A2
00
01
DSC-W5
DSC-W15
31
DSC-W17
31
35
37
Exif Model Data
Data
Page
Address
8F
E5
35
DSC-W7
37
8F
E6
00
00
Writing Method:
1) Select page: 00, address: 01 and set data: 01.
2) Select page: 4F, address: 8D and A2, and set the VIDEO OUT Dafault Data.
3) Select page: 8F, address: E5 and E6, and set the Exif Model Data.
4) Click [Save] on the SEUS screen.
5) Wait for more than 3 sec.
6) Select page: 80, address: 30, and check that the data is “00”.
7) Select page: 00, address: 01, and set data: 00.
DSC-W5/W7/W15/W17
9-876-856-81
Sony EMCS Co.
2005G0500-1
© 2005.7
Published by DI Technical Support Department
DSC-W5/W7/W15/W17
LEVEL
2
DSC-W5/W7
SERVICE MANUAL
US Model
Canadian Model
Argentine Model
Brazilian Model
Japanese Model
DSC-W5/W7/W15/W17
Ver 1.3 2005.12
AEP Model
UK Model
E Model
Australian Model
Hong Kong Model
Korea Model
Tourist Model
DSC-W5/W7/W15
Chinese Model
SUPPLEMENT-2
(PV05-071)
• Addition of SERVICE NOTE
• SY-001 BOARD TYPE CHECK (DSC-W7/W17)
DSC-W5/W7/W15/W17
9-876-856-83
Sony EMCS Co.
2005L0500-1
© 2005.12
Published by DI Technical Support Department
1. SERVICE NOTE
1-8. SY-001 BOARD TYPE CHECK (DSC-W7/W17)
The SY-001 board type can be discriminated with the mounted parts.
Note: When the data has changed because of board replacing etc., check the data setting is right. If not, rewrite to the right value.
Checking Method:
1) Refer to “SECTION 2 DISASSEMBLY” to remove the SY-001 board.
2) Referring the following figure, each type is discriminated with the mounted parts on the SY-001 board.
SY-001 BOARD (SIDE B)
X201
Mount
: Former Type
No Mount: New Type
• Differences of mounted parts on the SY-001 board
Ref. No.
R238
Former Type
XX
New Type
0
R305
XX
0
R306
0
XX
R309
XX
0
R349
0
XX
X201
67.5MHz
XX
• Differences of data
Page
7D
Address
E2
Former Type
00
New Type
FF
Writing Method:
1) Select page: 00, address: 01 and set data: 01.
2) Select page: 7D, address: E2, and set data: 00 (Former type) or data: FF (New type).
3) Click [Save] on the SEUS screen.
4) Wait for more than 3 sec.
5) Select page: 80, address: 30, and check that the data is “00”.
6) Select page: 00, address: 01, and set data: 00.
DSC-W5/W7/W15/W17
—2—
DSC-W5/W7/W15/W17
LEVEL
2
DSC-W5/W7
SERVICE MANUAL
US Model
Canadian Model
Argentine Model
Brazilian Model
Japanese Model
DSC-W5/W7/W15/W17
Ver. 1.4 2007.04
AEP Model
UK Model
E Model
Australian Model
Hong Kong Model
Korea Model
Tourist Model
DSC-W5/W7/W15
Chinese Model
SUPPLEMENT-3
(DI06-187)
• Addition of Language Group Table
GP1
GP2
GP3
GP4
GP5
J
US
CND
AUS
Vietnam
AEP
UK
E
AR
BR
TW
JE
HK
CH
KR
Korean
Russian
Swedish
Arabic
Dutch
Simplified
Chinese
Traditional
Chinese
Italian
Portugal
German
Spanish
Japanese
English
French
Area
• Language that can be selected about SY-001 board
z
z z
z z
z
z
z z z z z z
z z z
z
z
z
z
z
z
z
z
z
z
z
z
DSC-W5/W7/W15/W17
9-876-856-84
Sony EMCS Co.
• Abbreviation
CH : Chinese model
J
: Japanese model
JE : Tourist model
KR : Korean model
2007D0500-1
© 2007.4
DSC-W5/W7/W15/W17
LEVEL
2
DSC-W5/W7
SERVICE MANUAL
US Model
Canadian Model
Argentine Model
Brazilian Model
Japanese Model
DSC-W5/W7/W15/W17
Ver. 1.5 2007.09
AEP Model
UK Model
E Model
Australian Model
Hong Kong Model
Korea Model
Tourist Model
DSC-W5/W7/W15
Chinese Model
SUPPLEMENT-4
(DI07-147)
• Change of Board’s Suffix No.
• Change of Repair Parts
• Revision of Accessories
Note: Please refer to Ver.1.5 of SERVICE MANUAL (9-876-856-31) for the revision of accessories.
• Suffix No. of CD-545 flexible board and CD-546 flexible board have been changed from 11 into 12 .
About suffix No. 11 and 12 , there are no changes of schematic diagram and printed wiring board.
: Points changed portion.
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
SW-001 BOARD (CONTROL SWITCH)
(Service manual page 4-31, Location B-3 to D-5)
Former
S459
W
2
4
New
S459
W
LND452
1
2
STATIC_GND
LND451
3
4
LND452
1
STATIC_GND
LND451
3
STATIC_GND
R)
2
1
4
3
R457
2200
CN452
6P
6
N.C.
N.C.
5
N.C.
N.C.
4
N.C.
3
BL_L
3
BL_L
2
N.C.
2
N.C.
1
BL_H
1
BL_H
6
N.C.
5
4
R)
2
1
4
3
R457
2200
DSC-W5/W7/W15/W17_L2
9-876-856-87
D453
XX
D455
XX
6P
D452
XX
CN452
D451
XX
D453
XX
D455
XX
D452
MAZS068008SO
D451
MAZS068008SO
STATIC_GND
Sony EMCS Co.
2007I0500-1
© 2007.9
! : Points deleted portion.
5-1. EXPLODED VIEWS
Page
Former
Ref. No. Part No.
1
1
1
5-2
1
1
1
New
Ref. No. Part No.
Description
1-479-037-11 SWITCH BLOCK, CONTROL (SILVER) (W5)
1-479-037-31 SWITCH BLOCK, CONTROL (BLACK)
(W15)
1-479-037-41 SWITCH BLOCK, CONTROL (BLACK) (W7)
(W17)
1
1
1
1
1
1
Description
(W15)
(W17)
55
55
%53
54
53
52
54
52
66
66
67
67
51
5-3
51
58
MIC901
%58
59
MIC901
%57
57
60
60
63
53
57
58
63
2-515-716-01 SHEET, GRIP ADHESIVE
2-348-166-01 CUSHION, MICROPHONE
2-348-185-01 CUSHION, MICROPHONE (B)
—2—
59
Page
Former
Ref. No. Part No.
101
101
101
101
101
101
5-4
101
101
101
101
New
Ref. No. Part No.
Description
A-1096-995-A SY-001 BOARD, COMPLETE (SERVICE)
(GP1) (W5: J)
(GP2) (W5: US, CND, AUS/W15: AUS)
(GP1) (W7: J)
(GP3) (W5: AEP, UK/W15: AEP, UK)
101
(GP4) (W5: AR, BR, E/W15: E)
(GP5) (W5: CH, HK, KR, JE/
W15: CH, HK, KR, JE)
(GP4) (W7: AR, BR, E/W17: E)
W17: HK, KR, JE)
101
0 BT901 1-756-527-31 HOLDER, BATTERY (WITH TERMINAL)
(W7: SILVER)
5-5
156
1-788-176-11 OPTICAL FILTERBLOCK (OFB-02-21)
(W7/W17)
101
101
101
101
101
101
101
101
Description
A-1096-995-C SY-001 BOARD, COMPLETE (SERVICE)
(GP1)(W5: J)
(GP1) (W7: J)
(GP4) (W5: AR, BR, E/W15: E)
W15: CH, HK, KR, JE)
(GP4) (W7: AR, BR, E/W17: E)
W17: HK, KR, JE)
0 BT901 1-756-534-31 BATTERY HOLDER (TERMINAL)
(W7: SILVER)
156
1-788-306-11 OPTICAL FILTERBLOCK (OFB-02-26)
(W7/W17)
sécurité.
Page
Former
Ref. No. Part No.
New
Description
Ref. No. Part No.
***********************
***********************
< CONNECTOR >
< CONNECTOR >
CN451 1-817-549-11 CONNECTOR, FPC (LIF (NON-ZIF)) 8P
CN452 1-816-654-31 FFC/FPC CONNECTOR (LIF) 6P
* CN451 1-816-655-51 FFC/FPC CONNECTOR (LIF) 8P
* CN452 1-816-654-51 FFC/FPC CONNECTOR (LIF) 6P
< DIODE >
5-8
D451
D452
< DIODE >
8-719-056-54 DIODE MAZS068008SO
8-719-056-54 DIODE MAZS068008SO
< SWITCH >
S454
S456
S457
S458
S460
Description
1-786-157-11
1-786-157-11
1-786-157-11
1-786-157-11
1-786-157-11
< SWITCH >
SWITCH, TACTILE (g(REVIEW))
SWITCH, TACTILE (F(SELF TIMER))
SWITCH, TACTILE (a(SET))
SWITCH, TACTILE (f(FLASH))
SWITCH, TACTILE (G(MACRO))
—3—
S454
S456
S457
S458
S460
1-771-138-21
1-771-138-21
1-771-138-21
1-771-138-21
1-771-138-21
SWITCH, KEY BOARD (g(REVIEW))
SWITCH, KEY BOARD (F(SELF TIMER))
SWITCH, KEY BOARD (a(SET))
SWITCH, KEY BOARD (f(FLASH))
SWITCH, KEY BOARD (G(MACRO))
[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)]
Toolbar
Printing a text
Reversing the screens displayed once
1. Click the Print button
.
2. Specify a printer, print range, number of copies, and other options, and then click [OK].
• To reverse the previous screens (operation) one by one, click
.
the
• To advance the reversed screens (operation) one by one, click
the
.
Application of printing:
To set a range to be printed within a page, select the graphic
and drag on the page to enclose a range to
selection tool
be printed, and then click the Print button.
Application to the Service Manual:
This function allows you to go and back between circuit diagram and printed circuit board diagram, and accordingly it
will be convenient for the voltage check.
Finding a text
1. Click the Find button
.
2. Enter a character string to be found into a text box, and click
the [Find]. (Specify the find options as necessary)
To execute “find” from current page toward the previous pages,
select the check box “Find Backward” and then click the
“Find”.
Moving with link
1. Select either palm tool
, zoom tool
, text selection tool
, or graphic selection tool
.
2. Place the pointer in the position in a text where the link exists
(such as a button on cover and the table of contents page, or
blue characters on the removal flowchart page or drawing
page), and the pointer will change to the forefinger form
.
3. Then, click the link. (You will go to the link destination.)
Moving with bookmark:
Click an item (text) on the bookmark pallet, and you can move
to the link destination. Also, clicking
can display the
hidden items.
(To go back to original state, click
)
3. Open the find dialog box again, and click the [Find Again] and
you can find the matched character strings displayed next.
(Character strings entered previously are displayed as they are
in the text box.)
The parts on the drawing pages (block diagrams, circuit diagrams, printed circuit boards) and parts list pages in a text
can be found using this find function. For example, find a
Ref. No. of IC on the block diagram, and click the [Find Again]
continuously, so that you can move to the Ref. No. of IC on
the circuit diagram or printed circuit board diagram successively.
Note: The find function may not be applied to the Service
Manual depending on the date of issue.
Zooming or rotating the screen display
“Zoom in/out”
• Click the triangle button in the zoom control box to select the
display magnification. Or, you may click
ing in or out.
or
for zoom-
Switching a page
• To move to the first page, click the
.
• To move to the last page, click the
.
• To move to the previous page, click the
• To move to the next page, click the
.
.
“Rotate”
• Click rotate tool
, and the page then rotates 90 degrees each.
The printed circuit board diagram you see now can be changed
to the same direction as the set.
Reverse
987685636.pdf
Revision History
Ver.
Date
1.0
2005.01
Official Release
—
S.M. Rev.
issued
—
1.1
2005.07
Supplement-1
(S1 PV05-033)
• Precaution on Replacing the SY-001 Board
No
1.2
2005.09
2005.12
• Correction of Repair Parts
S.M. correction: Page 5-2
• Addition of SERVICE NOTE
(SY-001 BOARD TYPE CHECK (DSCW7/W17))
Yes
1.3
Correction-1
(C1)
Supplement-2
(S2 PV05-071)
1.4
2007.04
Supplement-3
(S3 PV06-187)
• Addition of Language Group Table
No
1.5
2007.09
Supplement-4
(S4 DI07-147)
• Change of Board’s Suffix No.
• Change of Repair Parts
• Revision of Accessories
S.M. revised: Page 5-13
Yes
DSC-W5/W7/W15/W17
History
Contents
No

Service Manual of Sony DSC

Transcription

Similar documents

service manual - SONYRUS :: OnLine Store

DSC-W5/W7/W15/W17

Service Manual Level 2

service manual