SPECIALTY VALVES

SPECIALTY VALVES
Calibrated Needle Valves
The Chemtrol calibrated needle valve is ideally suited to the fine regulation of
liquid flow required in instrumentation and laboratory work. The flow through
the 1/4” valve can be accurately adjusted by observing the knob handle exposing
numerals molded on the valve body. It has a positive stop for safe operation and
Teflon seats to prevent wear on needle
T45CN-V
1/4" FPT x 1/4" FPT
KNOB POSITION
FLOW RATE
(GPM @50 PSI)
1
2
3
4
5
6
7
8
0.85
1.41
1.79
2.15
2.42
3.15
4.40
4.50
The Chemtrol chemcock valve is ideal for laboratories, monitoring systems,
sampling, and a variety of other applications as original equipment. Its
calculated fluid flow coefficient (Cv) is based on the laying length being
equivalent to 1/4” Schedule 80 pipe. It opens and closes with only a quarter
turn. These valves come complete with replaceable FPM O-ring seats and
seals and exhibits no sticking or galling. It is rated at 150 psi at 73.4°F(23°C)
water –non-shock–full port.
DESCRIPTION
1/4" Hose x 1/4" MPT
1/4" MPT x 1/4" MPT
For on/off, restricted flow or sampling
applications, the Hayward LC12 StopCock is
easily adaptable to any piping connection.
Furnished with the valve is a 1/4˝ NPT female
pipe thread, 1/4˝ NPT male pipe thread and
hose barb end connectors for 1/4˝ through
7/16˝ I.D. tubing. These allow the valve to be
fitted with up to six different end connection
combinations. Simply attach the end
connections you need – they are all supplied
with each valve.
The Chemtrol Y-pattern globe valve exhibits minimal pressure-drop, even when
compared with a conventional upright style globe valve. Therefore, it is an
excellent choice for combination on-off and throttling applications. One of the
more common applications for this valve is as a pump by-pass control valve. It
features malleable glass reinforced PTFE (Teflon) seat disk ensuring long-lasting
positive sealing and is constructed of PVC and FPM seals. The stub acme thread
on stem provides rapid open-close operation.
www.fabcoplastics.com
1/2"
2151207
6
7
8
Y Pattern Valves
1/4"
2151204
4
5
Hayward Universal Stopcocks
SIZE
PART #
2
3
Chemtrol PVC Chemcock Valves
PART #
A45CC-V
M45CC-V
1
3/4"
2151208
1"
2151209
9
10
3-25
SPECIALTY VALVES & ASSEMBLIES
Angle Valves
1
The Chemtrol Angle Valve is used where a higher pressure-drop is desirable. One of its more
common applications is as a pump by-pass control valve. It features malleable glass reinforced
PTFE (Teflon) seat disk ensuring long-lasting positive sealing and is constructed of PVC and FPM
seals. The stub acme thread on stem provides rapid open-close operation.
2
SIZE
PART #
3
1/2"
3/4"
1"
PVC Globe Valves
This PVC Globe Valve is heavy duty, extra strong, and is ideal for throttling
applications. They are slow closing reducing the likelyhood of water hammer.
They are available in sizes ranging from 2 1/2” to 6” in PVC and CPVC with flanged
ends. All valves are assembled with silicone-free, water soluble lubricant and are
suitable for vacuum service.
4
5
1/4"
2151804 2151807 2151808 2151809
SIZE
2 1/2"
3"
4"
6"
Notes:
PVC FLANGED ENDS
BUNA-N
EPDM
VITON®
6013-025 6023-025 6033-025
6013-030 6023-030 6033-030
6013-040 6023-040 6033-040
6013-060 6023-060 6033-060
• Maximum pressure rating of 150 psi
for PVC and CPVC.
• Temperature rated to 140 °F for PVC and 200 °F for CPVC.
Liquid Dispensing Assemblies
6
Liquid dispensing assemblies are ideal for distilled, deionized and
demineralized water, as well as chemical dispensing. They are available
in PVC, Natural PP and PVDF. All tips accept 1/8” to 1/2” I.D. tubing.
They are frequently used in labs, hospitals, and clean rooms.
PART #
FC-DA-15D
FC-DA-15W
FC-PDA-15D
FC-PDA-15W
FC-KDA-15D
FC-KDA-15W
FC-DA-20D
FC-DA-20W
FC-DA-30D
FC-DA-30W
FC-PDA-30D
FC-PDA-30W
FC-KDA-30D
7
8
9
10
3-26
CPVC FLANGED ENDS
EPDM
VITON® VITON®
6023-025C 6033-025C 2032-005
6023-030C 6033-030C 2032-007
6023-040C 6033-040C 2032-010
6023-060C 6033-060C 2032-012
PART #
FC-DA-35D
FC-DA-35W
FC-PDA-35D
FC-PDA-35W
FC-KDA-35D
FC-KDA-35W
TYPE
35
35
35
35
35
35
VALVE
T.U. BALL
T.U. BALL
T.U. BALL
T.U. BALL
T.U. BALL
T.U. BALL
TYPE
15
15
15
15
15
15
20
20
30
30
30
30
30
MATERIAL
PVC
PVC
PP
PP
PVDF
PVDF
PVC
PVC
PVC
PVC
PP
PP
PVDF
VALVE
NEEDLE
NEEDLE
NEEDLE
NEEDLE
NEEDLE
NEEDLE
BALL
BALL
SNAP
SNAP
SNAP
SNAP
SNAP
Foot Operated Valves
The foot operated valve features a Kynar coated spring, Viton O-rings (EPDM available),
mounting holes, molded body, and an automatic shut-off. It is extremely easy to mount
and comes in a normally closed position. The valve is opened by pushing the top with your
foot and allowing the spring to close it.
SIZE
PVC
PP
1/2"
3/4"
1"
FC-FOV-50 FC-FOV-75 FC-FOV-10
FC-PFOV-50 FC-PFOV-75 FC-PFOV-10
Toronto, Edmonton, Saskatoon, Vancouver, Montreal
PRESSURE CONTROL VALVES
Pressure Regulators
The pressure regulator comes in two different configurations; ½” to 1” is a straight thru
flow design and the 1½” to 2” is an offset port flow design. They both feature a top
entry adjustment knob with lock nut, Viton O-rings (EPDM available on request), Kynar
covered stainless springs. It will operate with inlet pressures of up to 100 PSI and is
adjustable from 10 psi to 80 psi. It is designed to reduce and stabilize line pressure.
SIZE
PVC
PP
PVDF
1/2"
FC-PR-50
FC-PPR-50
FC-KPR-50
3/4"
FC-PR-75
FC-PPR-75
FC-KPR-75
1"
FC-PR-10
FC-PPR-10
FC-KPR-10
1-1/2"
FC-PR-15
FC-PPR-15
-
2"
FC-PR-20
FC-PPR-20
-
Pressure Relief Valves
These adjustable pressure relief valves are available in PVC and PVDF in two
different body styles. They feature Viton O-rings for durability and easy
adjustment. All models are designed to prevent excessive line pressure.
PART #
FC-MPR-25-1
FC-MPR-25-2
FC-MPR-50-3
FC-MPR-75
SIZE
1/4"
1/4"
1/2"
3/4"
RANGE
10-80 PSI
60-120 PSI
10-120 PSI
10-100 PSI
These pressure by-pass valve will bypass excess fluid or air whenever the pressure you set with
the handle is exceeded. This valve can be controlled from 10 through 100 PSI. Our pressure bypass valve will permit straight through flow if mounted in a straight line. These valves feature
Viton O-rings and adjustment knob and lock nut.
1/2"
FC-P-50
FC-PYP-50
FC-KP-50
3/4"
FC-P-75
FC-PYP-75
FC-KP-75
1"
FC-P-10
FC-PYP-10
FC-KP-10
1-1/2"
FC-P-15
FC-PYP-15
-
2"
FC-P-20
FC-PYP-20
-
+GF+ V786 Pressure Retaining Valve
The Pressure Retaining Valve serves to keep the working or system related pressures
constant, to balance out pressure pulsation, and to reduce pressure peaks in chemical
process systems. If the inlet pressure rises above the set value, the pressurized valve piston
is lifted against the spring force. Consequently, the valve opens and there is a reduction of
pressure through the outlet pipe. The valve closes as soon as the inlet pressure sinks below
the pre-set spring tension. The use of PRVs in upstream (supply side) UPW applications
without a point-of-use filter should be avoided. However, it should be noted that sufficient
flow is needed to avoid microbial contamination.
Notes:
• Provides highly accurate and stable pressure control.
• Size range 1/2” - 1 1/2”.
• Available in PVC, PP and PVDF.
• Diaphragms in EPDM or PTFE.
• Female NPT is standard. Also available with IR/BCF,
socket union and flanged end connections.
• Spare parts are available for these valves. Contact
customer service for more information.
www.fabcoplastics.com
INCH MATERIAL
SET
RANGE
BODY
TYPE
1/2
PVC
7-150
786
3/4
PVC
7-150
786
1
PVC
7-150
786
1 1/4
PVC
7-150
786
1 1/2
PVC
7-150
786
EPDM
SEATS
199 041
806
199 041
807
199 041
808
199 041
809
199 041
810
2
3
4
MATERIAL
PVC
PVC
PVC
PVC
Pressure By-Pass Valves
SIZE
PVC
PP
PVDF
1
PTFE
SEATS
199 041
817
199 041
818
199 041
819
199 041
820
199 041
821
5
6
7
8
9
10
3-27
PRESSURE CONTROL VALVES
+GF+ V185/V85 Pressure Relief Valves
1
The Pressure Relief Valve serves to keep the working or system pressures constant,
to balance out pressure pulsation, and to reduce pressure peaks in process systems.
The third pipe spigot fitted on the valve body means the valve can be installed directly
in the main pipeline. If the inlet pressure rises above the set value, the pressurized
valve piston is lifted against the spring force. Consequently, the valve opens and
there is a reduction of pressure in the outlet pipe. The excess pressure can exhaust
or be redirected via the third outlet. The valve closes as soon as the inlet pressure
sinks below the pre-set spring tension. The use of PRVs in upstream (supply side)
UPW applications without a point-of-use filter should be avoided. However, it should
be noted that sufficient flow is needed to avoid microbial contamination. It provides
highly accurate and stable pressure control .
2
3
INCH MATERIAL
1/2
PVC
3/4
PVC
1
PVC
1 1/4
PVC
1 1/2
PVC
2
PVC
2½
PVC
3
PVC
4
PVC
4
5
BODY TYPE
185
185
185
185
185
185
85
85
85
EPDM ORINGS
199 041 541
199 041 542
199 041 543
199 041 544
199 041 545
199 041 546
199 041 785
199 041 786
199 041 787
PTFE ORINGS
199 041 548
199 041 549
199 041 550
199 041 551
199 041 552
199 041 553
199 041 788
199 041 789
199 041 790
Notes:
• Size range 3/8” - 4”.
• Available in PVC, PP and PVDF.
• Diaphragms in EPDM or PTFE.
• Female NPT is standard. Also available with IR/BCF, socket union and flanged end connections.
• Spare parts are available for these valves. Contact customer service for more information.
6
+GF+ V782 Pressure Reducing Valve
The Pressure Reducing Valve reduces the pressure within the system to a pre-set value.
By using the differential pressure, the pressure reducing valve adjusts itself to the set
working pressure. The outlet pressure (working pressure) is not directly related to the
inlet pressure. If the outlet pressure increases or decreases above/below the desired
value, the diaphragm is lifted against the spring force or pressed down by the spring force,
as the case may be, by the outlet pressure. The pressure reducing valve begins to close/
open until a state of equilibrium is re-established; in other words, the outlet pressure
remains constant irrespective of an increasing or decreasing inlet pressure. The use of
PRVs in upstream (supply side) UPW applications without a point-of-use filter should be
avoided. However, it should be noted that sufficient flow is needed to avoid microbial
contamination. It provides highly accurate and stable pressure control
7
8
9
SET RANGE
7-150
7-150
7-150
7-150
7-150
7-150
14-90
14-90
14-60
INCH
1/2
3/4
1
1 1/4
1 1/2
MATERIAL
PVC
PVC
PVC
PVC
PVC
SET RANGE
7-150
7-150
7-150
7-150
7-150
BODY TYPE
782
782
782
782
782
EPDM ORINGS
199 041 572
199 041 573
199 041 574
199 041 575
199 041 576
PTFE ORINGS
199 041 584
199 041 585
199 041 586
199 041 587
199 041 588
Notes:
10
3-28
• Size range 1/2” - 1 1/2”
• Available in PVC, PP and PVDF
• Diaphragms in EPDM or PTFE
• Female NPT is standard. Also available with IR/BCF, socket union and flanged end connections
• Spare parts are available for these valves. Contact customer service for more information.
Toronto, Edmonton, Saskatoon, Vancouver, Montreal
PRESSURE CONTROL VALVES
+GF+ V182/V82 Pressure Regulating Valves
The Pressure Regulating Valve reduces pressure to a given value. By utilizing the
differential pressure, the valve sets itself to the set working pressure and maintains
it on the downstream side, irrespective of fluctuations of inlet pressure or changes
in flow. The valve is adjusted by a set screw and secured with a locknut. The use
of PRVs in upstream (supply side) UPW applications without a point-of-use filter
should be avoided. However, it should be noted that sufficient flow is needed to
avoid microbial contamination. This valve provides highly accurate and stable
pressure control.
1
2
Notes:
• Size range 1/2” - 4”.
• Available in PVC, PP and PVDF.
• Diaphragms in EPDM or PTFE for 2” and 4”, V82 design.
• 1/2”-1 1/2” V182 body with piston and O-ring design.
• Female NPT is standard. Also available with IR/BCF, socket union and flanged
end connections.
• Spare parts are available for these valves. Contact customer service for
more information.
INCH MATERIAL SET RANGE BODY TYPE EPDM ORINGS
1/2
PVC
7-150
182
199 041 745
3/4
PVC
7-150
182
199 041 746
1
PVC
7-150
182
199 041 747
1 1/4
PVC
7-150
182
199 041 748
1 1/2
PVC
7-150
182
199 041 749
2
PVC
7-150
82
199 041 307
2 1/2
PVC
14-90
82
199 041 773
3
PVC
14-90
82
199 041 774
4
PVC
14-60
82
199 041 775
FPM ORING PTFE DIAPHRAGM
199 041 750
199 041 751
199 041 752
199 041 753
199 041 754
199 041 308
199 041 776
199 041 777
199 041 778
The Pressure Retaining Valve serves to keep the working or system related pressures
constant, to balance out pressure pulsation and to reduce pressure peaks in process
systems. If the inlet pressure rises above the set value, the pressurized valve
piston is lifted against the spring force. Consequently, the valve opens and there
is a reduction of pressure through the outlet pipe. The valve closes as soon as the
inlet pressure sinks below the pre-set spring tension. When used as a bypass, it
can also function as a relief valve to reduce pressure peaks. The use of PRVs in
upstream (supply side) UPW applications without a point-of-use filter should be
avoided. However, it should be noted that sufficient flow is needed to avoid microbial
contamination. It provides highly accurate and stable pressure control.
Notes:
SET RANGE
7-150
7-150
7-150
7-150
7-150
7-150
14-90
14-90
14-60
BODY TYPE EPDM ORINGS
186
199 041 555
186
199 041 556
186
199 041 557
186
199 041 558
186
199 041 559
186
199 041 560
86
199 041 779
86
199 041 780
86
199 041 781
PTFE ORINGS
199 041 562
199 041 563
199 041 564
199 041 565
199 041 566
199 041 567
199 041 782
199 041 783
199 041 784
• Provides highly accurate and stable pressure control.
• Size range 1/2” - 4”.
• Available in PVC, PP and PVDF
• Diaphragms in EPDM or PTFE.
• Female NPT is standard. Also available with IR/BCF, socket union and flanged end connections.
• Spare parts are available for these valves. Contact customer service for more information.
www.fabcoplastics.com
4
5
+GF+ V182/V82 Pressure Regulating Valves
INCH MATERIAL
1/2
PVC
3/4
PVC
1
PVC
1 1/4
PVC
1 1/2
PVC
2
PVC
2 1/2
PVC
3
PVC
4
PVC
3
6
7
8
9
10
3-29
PLAST-O-MATIC VALVES & CONTROLS
Blue Standard Imported Valves
1
The Blue Standard line is Plast-O-Matic Valves’ solution for price sensitive
thermoplastic valve requirements. If you currently specify imported
or mass-produced plastic valves for water, corrosive or high purity
applications, Blue Standard provides the same quality and performance
levels, with the advantage of Plast-O-Matic technical services, testing
and support.
2
• BALL VALVES
• BUTTERFLY VALVES
• BALL CHECKS
• WEIR-TYPE DIAPHRAGM VALVES
• LABCOCKS
• Y STRAINERS
3
4
5
Body and Seal Materials
STANDARD BODY MATERIALS
Most Plast-O-Matic products are available in Grade 1,
Type 1 Geon® PVC, Corzan® CPVC, Kynar® PVDF, and
Natural Unpigmented Polypropylene. Most products
are also offered in PTFE, while molded products are
available in Glass-filled Polypro and Halar® ECTFE.
Other thermoplastics available, please consult FABCO.
6
7
8
9
10
3-30
SEAL MATERIALS
Elastomer seals include EPDM, FKM Viton®, FFKM, Aflas.
Thermoplastic seals include PFA, TFM, and PTFE. Special
and custom materials, including Kalrez®, Chemraz®,
and custom formulations are quoted on request. PlastO-Matic also offers a number of proprietary elastomers,
including f 99® for 99% sulfuric applications, EPDMh2®
for pinch valve applications, and others.
Pressure Relief, By-Pass & Anti-Siphon Valves
also known as Backpressure Regulators
Series “RVDT” PTFE
DIAPHRAGM
Series “TRVDT” THREE-WAY VALVE
PTFE diaphragm provides the
ultimate in corrosion resistance,
contamination-free sealing and
all-around versatility. No wetted
elastomers. Patented Fail Dry®
safety feature. For water, highly
aggressive
and
ultra-pure
liquid applications. PVC, CPVC,
Polypropylene, PVDF (Kynar®),
PTFE. Sizes: 1/4" to 2".
Third port offers piping convenience for bypass
applications. PTFE diaphragm provides the ultimate
in corrosion resistance and contamination-free
sealing. No wetted elastomers. Patented Fail Dry®
safety feature. For highly aggressive and ultra-pure
liquid applications. PVC, CPVC, Polypropylene, PVDF
(Kynar®), PTFE. Sizes: 1/2" to 1".
Series “RVT” and “RVD” GRADUAL OPENING
Prevent over pressures, maintain back pressures or automatic by-pass in vessels and
piping. Series RVDM (not shown) in-line pattern has a frictionless rolling diaphragm
design for sensitive operation. Series RVT is an angle-pattern design. Settings from
5 to 100 PSI. Fail Dry®, 1/2" to 2". Series RVD angle pattern diaphragm design (not
shown) 1/8" to 1/2" NPT, 50 to 150 PSI. Series RVTX offered in 3” NPT.
Toronto, Edmonton, Saskatoon, Vancouver, Montreal
PLAST-O-MATIC VALVES & CONTROLS
Pressure Regulating Valves
Series “PRH”and Series “PRHM”
PRESSURE REGULATOR
Accurately reduce and regulate steady
or varying inlet pressures and maintain a
constant predetermined maximum outlet
set pressure. Recognized as the industry’s
top performer for maximum flow with
minimal drop-off from set pressure.
Regulator setting from 5 to 125 PSI; some
size/material combinations have less range.
Sizes 1/4" to 3" in PVC, Natural Polypro and
PVDF; 1/4" to 11/2" in CPVC and PTFE.
Series “PRA” AIR LOADED
PRESSURE REGULATOR &
Series “PRS” PRESSURE
STABILIZER
Outperforms
spring
loaded
regulators through improved
response to pressure changes;
pressure is maintained without
sacrificing flow. Incorporates
the patented Fail Dry® safety
feature. Regulator settings from
5 to 125 PSI. Sizes 1/4" to 3". Used with the patented
Stabilizer® Series PRS, the PRA will perform with
virtually zero drop off from set pressure. Performance
rivals exotic control valves but at much lower costs.
1
Series “PRD” Differential
Regulator
Regulates pressure differential across
filters, instruments, etc. to ensure
that pressure going into the protected
segment of the system does not
exceed the output pressure. This valve
minimizes pressure drop and improves
performance while protecting the filters
or instruments from overpressure. Sizes
1/4" to 3" in PVC, Natural Polypro, other
materials on request.
Series “PRH-U” and “UPR”
ULTRA-PURE REGULATORS
The ultimate high purity pressure
regulators.
PRH-U
features
machined Kynar 740 body with
metal ion-free EPDM elastomer
and nonrising adjustment. UPR
has convoluted TFM diaphragm
and no external fasteners and
is designed to meet SEMI F-57
specifications. PRH-U regulator setting from 10 to 125 PSI,
sizes 1/4” to 3”. UPR setting from 5 to 100 PSI, sizes 1/4”
to 2”. Both PRH-U and UPR include choice of spigot types.
Also include proprietary POM pre-assembly cleaning, 16
hour cold/hot rinse, and final Class 100 clean and doublebag procedure.
Check Valves & Vacuum Breakers
Series “CKM”
DIAPHRAGM CHECK
VALVES & Series “CKS”
SELF-CLOSING CHECK
VALVES
Leak-proof check valves prevent
reverse flow of water, extremely
corrosive and ultra-pure liquids.
Self-sealing
designs
allow
mounting in any position.
Unique molded diaphragm in
sizes 1/2", 3/4" and 1"; selfguided poppet in 11/2", 2” and 3”. Both styles are
normally-closed – no reverse pressure required.
They operate silently, and seat in the same location
every time. PVC, CPVC, Polypro, PVDF.
Series “VBM” and “VBS” VACUUM
BREAKERS
Protective vacuum breakers eliminate
unwanted siphonage or collapsing of
storage tanks. Sensitive molded diaphragm
offers normally closed operation and
will respond to a minimum of vacuum;
however, they are not recommended for
protection of thin-wall tanks. Sizes 1/2",
3/4" and 1" NPT. New Series VBS features
normally-closed design, higher capacity in
sizes 11/2", 2" and 3" NPT.
Series “CK” and “CKD” SPECIAL PURPOSE DIAPHRAGM CHECK VALVES
Series CK is a machined PTFE valve that features the same normally-closed diaphragm
design as Series CKM, available in 3/4"and 1" sizes. Series CKD is a normally-open
diaphragm check valve that is ideal for ultra-low pressure or flow, requires .5 PSI to close.
Sizes 1/4" and 1/2" in PVC, Natural Polypro, PTFE and PVDF.
www.fabcoplastics.com
2
3
4
5
6
7
8
9
10
3-31
PLAST-O-MATIC VALVES & CONTROLS
Solenoid Valves
1
Series “EAST” COMPACT,
DIRECT OPERATING
This compact, direct-acting design
provides a cost effective solution for
high pressure rated applications, where
space is limited. Patented Fail-Dry®
safety design. For virtually all type
solutions: acids, caustics, solvents,
chlorine solutions and ultra-pure liquids.
2,000,000 cycle life. Sizes 1/4" and
1/2". Cv of 0.5 with 3/16" orifice; 0.8
with 1/4" orifice. PVC, CPVC, Natural
Polypro, PVDF.
2
3
High pressure, high flow capability.
Pilotoperated design requires 5
PSI differential across the valve.
Rated for inlet pressures 5 to 140
PSI, back-pressures to 70 PSI.
Cv’s from 5.2 to 80. Patented FailDry® safety design. PTFE bellows
barrier type seal. For all type
solutions. Sizes 1/2" to 3”. PVC,
CPVC, Natural Polypro, PVDF.
Series “EASMT” and
“EASYMT” DIRECT
OPERATING PTFE
BELLOWS
4
SPECIAL PURPOSE
SOLENOID VALVES Series
“EASY-NO” and Series“THP”
Normally-open, direct-acting Series
EASYNO closes when energized.
Designed for applications that must
have continued flow in the event of a
power failure.Suitable for pressure,
drain or vacuum service with
pressures to 70 PSI. Direct-acting
Series THP is a multi-purpose valve
suitable for inlet and backpressures
to 100 PSI; it can function as
a three-way, normally-open, or
normally-closed valve. Both EASYNO and THP are available in 1/4"
and 1/2" sizes in PVC.
Direct-acting valve for severe
service
applications
with
virtually all solutions (acids,
caustic, etc.). Unique “Bellows”
design
provides
dynamic
barrier seal, prevents leaking
of emissions. 2,000,000 cycle
life. Fail-Dry® safety design.
Sizes 1/4" to 1”. Cv from 1.1
to 4.7, orifice from 3/8" to
11/16". PVC, CPVC, Glassfilled Polypro, PVDF.
5
6
Ball Valves
7
TRUE-BLUE™ Series “MBV” TRUE UNION MANUAL BALL VALVES
This engineered valve offers bubble-tight sealing and easy turning with perfectly machined,
polished smooth ball. Designed with trunnion to keep ball centered, reinforced shaft to
eliminate breakage and dual seals to insure reliability. PTFE seats are back-loaded with
O-rings for reduced torque and longer seat life. Every valve is built ready to accept actuation
in just minutes with no special tools or changes, and they are built for long cycle life. PVC,
CPVC, PP, and PVDF; 3-way Series TMBV available in PVC and CPVC Sizes: 1/2" through 4";
NPT, IPS, BSP, Metric Socket.
8
Series “ABV” and “ABR”
2-WAY and Series “TABV”
and “TABR” 3-WAY AIR TO
AIR or SPRING RETURN
PNEUMATIC ACTUATED
BALL VALVES
9
10
Series “PS” PILOT
OPERATED
Rugged engineered thermoplastic
construction – ideal for corrosive
atmospheres. Compact. lightweight assembly for reduced
piping stress. Simple attachment to True Blue™ Ball Valve
body mounting lugs. Manual override standard on most
models. Spring Return options. Limit Stops and Limit
Switches available. ABV sizes for 1/2" to 3", Rack and Pinion
ABR for sizes 1/4" to 4".
3-32
SERIES “LMBV”
LATERAL REDUCING
BALL VALVE
Revolutionary ball valve
adapter
eliminates
weakness inherent to
lateral
drops;
installs
easily into the tee without additional fittings. Also
an ideal replacement for costly zero dead-leg valves.
1/2" to 2" Ball Valves sizes. 3/4" to 3" tee adapters
standard; other sizes consult factory. Available in
PVC, CPVC, PVDF and natural polypropylene, socket
or butt fusion.
Toronto, Edmonton, Saskatoon, Vancouver, Montreal