Experience the Power of Confidence

Experience the
Power of Confidence
…the confidence of over fifty years of expertise in the research,
design, manufacture and support of high quality magnetic materials
and components.
A major supplier of the highest performance materials in the industry
including; MPP, High Flux, Kool Mµ ® , power ferrites, high
permeability ferrites and strip wound cores, Magnetics products set
the standard for providing consistent and reliable electrical properties
for a comprehensive range of core materials and geometries.
Magnetics is the best choice for a variety of applications ranging
from simple chokes and transformers used in telephone equipment
to sophisticated devices for aerospace electronics.
Magnetics backs its products with unsurpassed technical expertise
and customer service. Magnetics’ Application Engineering staff
offers the experience necessary to assist the designer from the initial
design phase through prototype approval. The knowledgeable Sales
representatives are available to help with all of your customer service
needs. This support, combined with a global presence via a
worldwide distribution network, including a Hong Kong distribution
center, makes Magnetics a premier supplier to the international
electronics industry.
Molypermalloy, High Flux
and Kool Mµ® Powder Cores
Magnetics’ Powder cores are excellent as low loss inductors for switchedmode power supplies, switching regulators and noise filters. A variety of
sizes and types are available.
MPP – Molypermalloy powder cores (MPP) are available in eight
permeabilities ranging from 14µ through 550µ, and have guaranteed
inductance limits of ±8%. Thirty sizes include I.D.s from 1.78 mm
(0.070") to 49.2 mm (1.938") and O.D.s from 3.56 mm (0.140") to 77.8 mm
(3.063"). Standard stabilization or temperature stabilized (as wide as
-65˚C at 125˚C) cores are available.
APPLICATIONS – Chokes, Converters, and EMI/RFI filters.
HIGH FLUX – High Flux powder cores have a much higher energy storage
capacity than MPP cores and are available in six permeabilities from 26µ
through 160µ. High Flux cores are available in sizes identical to MPP cores.
APPLICATIONS – Chokes, Converters, Inductors, Inverters, Pulse
Transformers and Switching Regulators.
KOOL Mµ ® – Kool Mµ powder cores have a higher energy storage
capacity than MPP cores and are available in six permeabilities from 26µ
through 125µ. Kool Mµ toroids are available with outside diameters
ranging from 4 mm to over 100 mm. Shapes such as E cores, U cores,
blocks and racetrack configurations are also available. E cores range in
size from 13 mm to 160 mm and are available in 26µ through 90µ. U
cores range in size from 55 mm through 80 mm (available permeabilities
are size dependent).
APPLICATIONS – PFC Chokes, Boost/buck Regulators, Inductors, Output
Inductors and Flybacks.
THINZ – MPP THINZ® are extremely low height (<1 mm) self-shielded
power inductor cores, allowing finished inductor heights in the 1.5 mm to
2 mm range. THINZ come in 5 sizes with O.D.s ranging from 3.1 mm
(0.120") through 7.9 mm (0.310") and four permeabilities: 125µ, 160µ, 200µ
and 250µ.
APPLICATIONS – POL DC/DC Converters, Portable Electronic Devices.
Ferrites
Magnetics’ ferrite cores are manufactured for a wide variety of applications.
Magnetics has developed and produces the leading MnZn ferrite materials for
power transformers, power inductors, wideband transformers, common mode
chokes, and many other applications. In addition to offering the leading
materials, other advantages of ferrites from Magnetics include: the full range
of standard planar E and I cores; the widest range of toroid sizes in power and
high permeability materials; standard gapping to precise inductance or
mechanical dimension; and a wide range of coil former and assembly
hardware available.
POWER MATERIALS
Four low loss materials are engineered for optimum frequency and
temperature performance in power applications. Magnetics’ L, R, P and F
materials provide superior saturation, high temperature performance, low
losses and product consistency.
SHAPES – Toroids (2mm to 180mm), E, ER, Planar E, I, EFD, EFD, ETD,
EER, EC, U,I, UR, PQ Pot cores, RS (round-slab), DS (double slab), RM,
EP, Special Shapes.
APPLICATIONS – Power Supplies, DC-DC Converters, Telecomm Data
Interfaces, Impedance Matching Transformers, Handheld Devices, High
Power Control (gate drive), Computer Servers, Distributed Power (DC-DC),
EMI Filters.
HIGH PERMEABILITY MATERIALS
Two high permeability materials (5000µ J material and 10000µ W
material) are engineered for optimum frequency and impedance
performance in signal, choke and filter applications. These Magnetics’
materials provide superior loss factor, frequency response, temperature
performance, and product consistency.
SHAPES – Toroids (2 mm to 140 mm), E, EFD, U, Pot cores, RS (roundslab), DS (double slab), RM, EP, Special Shapes.
APPLICATIONS – Common Mode Chokes, EMI Filters, Other Filters,
Current Sensors, Telecomm Data Interfaces, Impedance Matching
Interfaces, Handheld Devices, Spike Suppression, Gate Drive Transformers.
...the power
of confidence
SPECIAL MATERIALS
A number of special materials are engineered for specific performance
results, including frequency response, temperature factor, Curie temperature,
permeability across temperature for GFCI and telecomm performance, and
loss factor. Magnetics’ special materials provide outstanding performance,
customization options and superior product consistency.
SHAPES – Toroids (2mm to 140mm), E, Planar E, ETD, EC, U, I, Planar
PQ, Pot cores, RS (round-slab), DS (double slab), RM, EP, Special
Shapes.
APPLICATIONS – EMI Filters, Current sensors, Chokes, Tuned Filters, Data
interfaces, Special Temperature Requirements.
Machined Prototypes
and Custom Components
Magnetics’ world-class materials offer unique and powerful advantages to
almost any application. An even greater competitive edge can be gained
through innovations in new core shapes and custom geometries, and
Magnetics is poised to help. Our Rapid Prototyping Service can quickly
make a wide variety of core shapes in ferrite, MPP, High Flux, or Kool
Mu®. The time between receipt of your drawing and delivery of the parts
to you is usually less than 10 days. This quick turnaround time results in
a shorter design period, which gets your product to market faster. Plus,
our application engineers may be able to provide design assistance that
could lead to a lower piece price. To learn more about how our Rapid
Prototyping Service can help you shorten your design cycle, contact a
Magnetics Application Engineer.
Strip Wound Cores
Tape wound cores are made from high permeability alloys of nickel-iron,
grain oriented silicon-iron. The alloys are known as Orthonol®, Alloy 48,
Square Permalloy 80, Supermalloy and Magnesil®. Cores are available in
more than 50 standard sizes. For a wide range of frequency applications,
materials are produced in thicknesses from 0.013 mm (1/2 mil) through
0.356 mm (14 mils). Cases are robust nylon boxes, rated for 200° C
continuous operation and 2000 voltage minimum breakdown.
APPLICATIONS – Magnetic Amplifiers, Reactors, Regulators, Static
Magnetic Devices and Current Transformers.
Miniature Tape Wound Bobbin Cores are manufactured from Permalloy 80
and Orthonol ultra-thin tape (0.000125" to 0.001" thick). They are available
in widths from 0.031" to 0.250" (wider on special request). Wound on
non-magnetic stainless steel bobbins, core diameters are available down
to 0.050", with flux capacities as low as several maxwells. Magnetics’
sophisticated pulse test equipment reproduces most test programs and
can measure accurately in the millivolt-microsecond region.
APPLICATIONS – Magnetometers, Flux Gates, Oscillators, Inverters and
Magnetic Amplifiers.
Visit us at www.mag-inc.com
• Product Specifications
• Digital Library
• Downloadable Design Software
• Global Distribution Network
• Stock Check Distribution Inventory Locator
Magnetic Core Selection
Application
P.O. Box 11422
Pittsburgh PA 15238-0422
412.696.1333
1.800.245.3984
fax: 412.696.0333
[email protected]
www.mag-inc.com
Chokes
Common Mode Noise Filters
Converters
Current Transformers
Ballasts
Transformers
EMI/RFI Filters
Ground Fault Interrupters
Inductors – SMPS
Inductors – High Q Filters
In-Line Filters
Inverters
Load Coils
Magnetic Amplifiers
Magnetometers
Noise Filters
Oscillators
Power Factor Correction
Power Transformers
Proximity Devices/Sensors
Pulse Transformers
Saturating Transformers
Static Magnetic Devices
Switching Regulators
Voltage Regulators
Wide Band Transformers
Tape
Cores
•
•
•
Bobbin
Cores
MPP
Cores
High Flux Kool Mµ
Cores
Cores
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•