- Airxcel

Transcription

- Airxcel

Work Boat Air Conditioners
Models MVS & MVW
Air Source Models MVS60-90-120-144-180-240
Water Source models MVW60-90-120-144-180-240
Installation and Operation Manual
Chapter 1
Introduction & Safety Information..................................................................... 2
Chapter 2
General Description.......................................................................................... 3
Chapter 3
Installation Preparation..................................................................................... 4
Chapter 4
Installation....................................................................................................... 8
Chapter 5
Initial Start-Up & Shut Down........................................................................... 14
Chapter 6
Maintenance.................................................................................................. 15
Chapter 7 Troubleshooting.............................................................................................. 16
Chapter 8
Warranty........................................................................................................ 17
Appendix A Dimensional Drawings................................................................................... A-1
Appendix B Wiring Schematics.........................................................................................B-1
Appendix C Start-Up Check List........................................................................................C-1
Marvair® Division of AIRXCEL™, Inc
PO Box 400 • Cordele, GA 31010
156 Seedling Dr. • Cordele, GA 31015
(229) 273-3636 • Fax (229) 273-5154
Email: [email protected]
www.marvair.com/marine
Marvair® Marine UK
Unit 6 Benridge Park • Holyrood Close
Poole, Dorset BH17 7BD.
+44 (0)1202 650700
www.marvair.co.uk
MVS/MVW Installation & Operation Manual
10/2013 rev. 3
P/N 01850
Work Boat Air Conditioner
Introduction & Safety Information
Chapter 1
This manual is intended to be a guide to Marvair Marine’s line of vertical air and water source
air conditioners. It contains installation, troubleshooting, maintenance, warranty, and application
information. The information contained in this manual is to be used by the installer as a guide
only. This manual does not supersede or circumvent any applicable national or local codes.
If you are installing the MVS or MVW air conditioners, first read Chapter 1 & 2 and scan the
entire manual before beginning the installation as described in Chapter 4. Chapter 2 contains
general, descriptive information and provides an overview which can speed up the installation
process and simplify troubleshooting.
If a malfunction occurs, follow this troubleshooting sequence:
1. Make sure you understand how the air conditioners works (Chapters 2 & 5).
2. Identify and correct installation errors (Chapter 4).
3. Refer to the troubleshooting information in Chapter 8.
If you are still unable to correct the problem, contact the Factory at 1-800-841-7854 for additional
assistance. Please read the following “Important Safety Precautions” before beginning any work.
Important Safety Precautions
1. USE CARE when LIFTING or TRANSPORTING equipment.
2. TRANSPORT the UNIT UPRIGHT. Laying it down on its side may cause oil to leave the
compressor and breakage or damage to other components.
3. TURN ELECTRICAL POWER OFF AT THE breaker or fuse box BEFORE installing or
working on the equipment. LINE VOLTAGES ARE HAZARDOUS or LETHAL.
4. OBSERVE and COMPLY with ALL applicable PLUMBING, ELECTRICAL, and
BUILDING CODES and ordinances.
5. SERVICE may be performed ONLY by QUALIFIED and EXPERIENCED PERSONS. * Wear safety goggles when servicing the refrigeration circuit
* Beware of hot surfaces on refrigerant circuit components
* Beware of sharp edges on sheet metal components
* Use care when recovering or adding refrigerant
6. Use COMMON SENSE – BE SAFETY-CONSCIOUS
This is the safety alert symbol
. When you see this symbol on the unit and in the instruction
manuals be alert to the potential for personal injury. Understand the signal word DANGER,
WARNING and CAUTION. These words are used to identify levels of the seriousness of the hazard.
Failure to comply will result in death or severe personal injury and/or property
DANGER damage.
Failure to comply could result in death or severe personal injury and/or property
WARNING damage.
CAUTION Failure to comply could result in minor personal injury and/or property damage.
IMPORTANT is used to point out helpful suggestions that will result in improved installation,
reliability or operation.
MVS & MVW Installation & Operation Manual 10/2013 rev.3
Page 2 of 18
2.1 General Description
Chapter 2
The Marvair Marine self-contained water and air cooled air conditioners are designed for
indoor use in marine applications for both new installations and for replacement of older, less
efficient units. The air conditioners are available in cooling capacities of 5, 7½, 10, 12, 15, &
20 tons (60,000; 90,000; 120,000; 144,000; 180,000 and 240,000 BTUH’s) and are controlled
by a conventional 24 VDC wall mounted, HVAC type thermostat. The vertical configuration
minimizes floor space and blends into a variety of working environments. The cool, dry air can
be discharged directly into the room or ducted into adjacent rooms. To ensure years of dependable
performance, all components are housed in a superior corrosion resistant steel cabinet.
Air Cooled Units The MVS air cooled units have an indoor air mover, coil, compressor and
controls. A remote condenser (not provided by Marvair) connects to the MVS unit with field
installed refrigerant lines. The units are shipped with a dry nitrogen charge and may be used with
either R-22 or R-407c refrigerant.
Water Cooled Units The MVW water cooled air conditioners are packaged units shipped from
the factory with R-407c refrigerant and an internal condenser and ready to run. The coaxial
tube-in-tube condenser is constructed of corrosion resistant cupronickel water tubing and copper
refrigerant tubing for use in either fresh or sea water.
The 10, 12, 15 and 20 ton air conditioners have two compressors, allowing for staged operation.
The dual compressors can be programmed to start sequentially, minimizing start-up amps. In
addition to better humidity control and comfort, the dual compressors provide back-up protection,
increased operating efficiencies and energy savings.
The units are pre-piped and wired, minimizing installation time. The readily accessible control
center contains all the control components. On the MVS (air cooled) units, a 24 VAC relay is
included to cycle the condenser fans ON & OFF with the compressors.
Each condensate pan has two drains to prevent condensate from standing in the base pan. The
drain lines are internally tied together. The condensate drain line opening is conveniently located
on the right side of the air conditioner to facilitate connection of the external condensate line.
A manual high pressure switch and an auto reset low pressure switch protect the compressors
under abnormal operating conditions. A three minute delay on make safeguards the compressors
from destructive short cycling. The evaporator coils have a baked polyester coating rated to 1,000
hours salt spray test. The return air filters are located behind the return air grille and are accessible
from the front of the unit.
High Pressure Switch The high pressure switch is mounted on the compressor's discharge rotalock valve. The compressor will shutdown if the refrigerant rises to 350 PSIG. This protects the
compressor if the condenser air flow is restricted or if the outdoor fan motor fails (MVS units)
or the pump fails (MVW units). The high pressure switch must be manually reset before the
compressor circuit can be turned on. The reset button is located on the back of the switch.
Page 3 of 18
Low Pressure Switch The low pressure switch is mounted between the compressor and the
compressor's suction rota-lock valve. It is designed to open if the refrigerant pressure in the
suction line drops below 25 PSIG; it resets when the pressure rises to 50 PSIG. This switch
protects the unit if airflow through the indoor coil is restricted, the blower fails or there is a loss
of refrigerant.
2.2 Model Identification
•
•••
Refrigerant
N = Nitrogen charge
C = R-407c
MVS = Marine Vertical Split (air source)
MVW = Marine Vertical Water (water source)
AC
•••
Nominal Cooling
Capacity (BTUH)
60 = 60,000
90 = 90,000
120=120,000
144=144,000
180 = 180,000
240 = 240,000
Air Conditioner
•
Power Supply
C = 208-230V, 3ø, 60Hz
D = 460V, 3ø, 60Hz
•••
Cabinet Color
216 = Gray Cabinet (standard)
116 = Beige Cabinet (optional)
2.3 Serial Number Date Code
A =
B =
C =
D =
E =
F =
Month
Year
January G = July A = 2011
February H = August B = 2012
March J = September C = 2013 April K = October D = 2014
May L = November June M = December
IMPORTANT
WHEN THE AIR CONDITIONER IS INSTALLED, MODEL NUMBER AND SERIAL
NUMBERS ARE TO BE RECORDED AND MAINTAINED IN A LOCATION FOR IMMEDIATE
ACCESS WHEN REQUESTING FURTHER INFORMATION CONCERNING THIS UNIT.
3.1 Installation Preparation
Chapter 3
Inspect the air conditioner
The air conditioners are shipped on 4” x 4” wood base frames and wrapped in shrink wrap.
Remove the shrink wrap and verify the model number of the unit against the shipping order.
Make sure power supply at site matches the power supply of the air conditioner. Check the
air conditioner for any damage that may have occurred during shipping, especially concealed
damage. If the air conditioner is damaged or the shipment is not complete, immediately (within 14
days) file a claim with the freight company.
The units should be stored inside and not exposed to weather.
Page 4 of 18
Installation requirements
The MVS and MVW air conditioners must be installed on a hard, level, smooth surface. Do not
install the air conditioner on a carpeted floor.
Condensate
The locations of the condensate openings are shown on the dimensional drawings in Appendix A.
The factory installed condensate connection on the cabinet is a female, PVC fitting designed for a
¾” slip connection.
Access for the condensate tubing is on the right side or the unit.
CAUTION
INSPECT THE FLEXIBLE CONDENSATE DRAIN LINE INSIDE THE AIR CONDITIONER
FOR KINKS OR OBSTRUCTIONS IN THE LINE. CORRECT AS REQUIRED.
Power and control (thermostat) wiring
Line voltage power supply must be sized to provide adequate power for the operation of the
specific model air conditioner. Information on line power requirements, line sizing and fuse sizing
is shown on data label on unit. The line power conductors and control (thermostat) conductors
enter the air conditioner through knockouts on the right side of the cabinet. The location of the
knockouts are shown on the dimensional drawings in Appendix A.
Depending on the location of the air conditioner, the exact rough-in location for power lines and
low voltage conductors in the room can be determined. Allow sufficient length for both the high
and low voltage conductors (approximately 6 feet) from the outside of the cabinet to the low
voltage terminal board and the internal disconnect.
Location and Clearances
All MVS and MVW air conditioners have hinged doors on the front to facilitate access to the
primary components. The doors can be removed from the cabinet by removing the pins in each
door.
Thirty-six inches must be allowed in front of the units to permit the doors to swing open. For
units with right side electrical, condensate, refrigerant and water connections, allow sufficient
space between the air conditioner and an obstruction, e.g. a wall, to connect the lines.
Minimum clearance in the rear is zero inches. Clearance above the unit side depends on the space
required for the plenum and ductwork.
Page 5 of 18
Clearance for connections:
20" (508mm)
Clearance for door opening:
36" (914mm)
Figure 1. Clearances
3.2 Water connections on MVW water cooled air conditioners
The water in and water out connections on the air conditioners are on the right side of the
unit. Since the MVW120 & 144 have two compressors and each compressor can operate
independently, two sets of water pipes are required.
3.3 Remote air cooled condenser for MVS units
On MVS units with a remote condenser(s), locate the condenser(s) so that air flow is unrestricted
on all sides and above the condenser. Place the remote condensing unit(s) according to the
condensing unit’s installation instructions. Select a location that will minimize the length and
complexity of the piping runs. See Table 1 for size of piping. The refrigerant connections for the
units are on the right side of the unit. Since the MVS120, 144, 180 & 240 have two compressors
and each compressor can operate independently, two sets of refrigerant lines and two independent
condensers or a condenser with two independent circuits are required. An appropriately sized
condenser must be selected based upon the cooling capacity of the compressor.
Page 6 of 18
Model
MVS60
MVS90
MVS120
MVS144
MVS180
MVS240
Unit
Connect
Size
HG LIQ
Circuit
1
1
1
2
1
2
1
2
1
2
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
1-1/8
1-1/8
Length of Run (feet)
0-25
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
7/8
7/8
26-60
51-75
76-100
101-125
126-150
HG
LIQ
HG
LIQ
HG
LIQ
HG
LIQ
HG
LIQ
HG
LIQ
5/8
7/8
5/8
5/8
7/8
5/8
7/8
7/8
1-1/8
1-1/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
1-1/8
1-1/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
1-1/8
1-1/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
7/8
7/8
7/8
1-1/8
7/8
7/8
1-1/8
7/8
1-1/8
1-1/8
1-3/8
1-3/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
7/8
7/8
7/8
1-1/8
7/8
7/8
1-1/8
7/8
1-1/8
1-1/8
1-3/8
1-3/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
7/8
7/8
7/8
1-1/8
7/8
7/8
1-1/8
7/8
1-1/8
1-1/8
1-3/8
1-3/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
5/8
7/8
7/8
Table 1. Recommended Refrigerant Line Sizes
Duct
The evaporator blowers in the MVS and MVW units were selected to be used with duct. Refer to
Table 2 for air flow at various static pressures.
CFM @ Various Static Pressures for 208-230v. 3ø, 60 Hz. air conditioners
Model
Number
60
90
120
144
180
240
Indoor Motor / Blower
Air Flow (CFM) at External Static Pressure (in. wg)
HP
Qty
0.2
0.4
0.6
0.8
1.0
1.00
1.75
3.00
3.00
1.50
1.50
1
1
1
1
2
2
2,365
3,400
4,950
5,350
6,550
8,730
2,165
3,115
4,535
4,900
6,000
8,000
1,980
2,850
4,150
4,485
5,490
7,320
1,775
2,560
3,725
4,025
4,925
6,570
1,570
2,260
3,290
3,555
4,350
5,805
CFM @ Various Static Pressures for 460v. 3ø, 60 Hz. air conditioners
Model
Number
60
90
120
144
180
240
Indoor Motor / Blower
Air Flow (CFM) at External Static Pressure (in. wg)
HP
Qty
0.2
0.4
0.6
0.8
1.0
1.00
1.75
2.50
2.50
1.50
1.50
1
1
1
1
2
2
2,640
3,700
4,800
5,200
6,360
8,480
2,420
3,390
4,400
4,765
5,825
7,770
2,215
3,100
4,025
4,360
5,530
7,110
1,990
2,785
3,615
3,915
4,780
6,380
1,760
2,460
3,195
3,460
4,225
5,635
Air flows were measured with a wet indoor coil.
Table 2. CFM at Various Static Pressures
CAUTION
THE DUCT SYSTEM MUST BE ENGINEERED TO PROVIDE SUFFICIENT AIR FLOW
THROUGH THE AIR CONDITIONER, EVEN UNDER ADVERSE CONDITIONS SUCH
AS A DIRTY FILTER. PROPER DESIGN OF THE DUCT SYSTEM IS CRITICAL TO
MAXIMUM PERFORMANCE AND QUIET OPERATION.
Page 7 of 18
Chapter 4
4.1 Installation
Rig and place the air conditioner
WARNING: UNITS ARE HEAVY
THE MVS AND MVW AIR CONDITIONERS WEIGH IN EXCESS OF 1,000 LBS. WHEN
MOVING THE UNIT, SUFFICIENT MANPOWER AND MECHANICAL EQUIPMENT
MUST BE USED TO PREVENT DAMAGE TO THE UNIT AND INJURY TO PEOPLE. TO
FACILITATE MOVING THE AIR CONDITIONER, IT MAY BE NECESSARY TO LAY THE
UNIT ON ITS SIDE ON DOLLIES. IF THIS IS REQUIRED, USE MULTIPLE DOLLIES
AND PLACE THE UNIT ON ITS LEFT SIDE. THE UNIT SHOULD NOT REMAIN ON ITS
SIDE ANY LONGER THAN REQUIRED FOR THE ACTUAL MOVING PROCESS. IF THE
AIR CONDITIONER HAS BEEN ON ITS SIDE, DO NOT ATTEMPT TO START THE UNIT
UNTIL IT HAS BEEN VERTICAL FOR AT LEAST 24 HOURS.
To lift the air conditioners, use slings with a spacer under the base skid to prevent damage to the
cabinet when using a hoist. The air conditioners are designed to minimize noise and vibration. If
additional dampening is desired, place a rubber mat or other material designed for this purpose
and of sufficient quality to support the weight of the air conditioner. Unit must be level; not to
exceed 1/8” per linear foot in any direction.
Figure 2. Rigging Details
Page 8 of 18
MVS refrigerant line connections and charging
Install the remote air cooled condenser in accordance with the installation instructions provided
with the condenser. Locations for the connection of the refrigerant lines are shown on the
dimensional drawings in Appendix A. Recommended line sizes are shown in Table 1.
Trap Must Be Above Condenser Coil
Remote
Condensing
Unit
Line Slopes Toward Condenser
MVS Unit
Hot Gas Line
Liquid Line
Hot Gas Line
MVS Unit
Liquid Line
Line Slopes Toward Condenser
Remote
Condensing
Unit
Figure 3a. Condenser above evaporator
Figure 3b. Evaporator above condenser
The MVS air conditioners are shipped with a holding charge of nitrogen. After refrigerant
connections are made, release the nitrogen, evacuate, leak test and charge the system as described
below.
Charging MVS units
A. When outdoor condenser is not precharged with refrigerant.
1. Open hot gas and liquid line service valves.
2. Purge the nitrogen holding charge evacuate and leak test the system.
3. Using standard refrigeration charging techniques and charging charts, add refrigerant as required to maintain proper operating conditions. Additional charge is required for piping runs over 25 feet (760 cm). Add charge at the rate of 0.38 oz. per foot for piping runs over 25 feet (760 cm).
B. When outdoor condenser is precharged with refrigerant.
1. Connect line sets to the indoor unit and outdoor condensing unit.
2. Purge the nitrogen from the indoor unit, evacuate and leak test the unit.
3. Open the service valves and add refrigerant to maintain proper operating conditions. Additional charge is required for piping runs over 25 feet (760 cm). Add charge at the rate of 0.38 oz. per foot for piping runs over 25 feet (760 cm).
Page 9 of 18
IMPORTANT
CHARGE THE COMPRESSOR ON BOTH THE HIGH AND LOW SIDES SIMULTAN-EOUSLY
TO PREVENT AXIAL LOADING OF THE SCROLL, WHICH MAY CAUSE A TEMPORARY NO
START CONDITION FOR THE COMPRESSOR. IF THIS OCCURS, LEAVE THE COMPRESSOR
OFF FOR 30 MINUTES BEFORE RESTARTING, ALLOWING THE INTERNAL PRESSURES TO
EQUALIZE. IF REMOVING THE COMPRESSOR, EVACUATE BOTH THE HIGH AND LOW SIDE
SIMULTANEOUSLY.
Use charging chart supplied with the condenser, if available. If not available, block off enough of
the condenser coil to maintain 220 psig discharge pressure and charge to 15°F to 20°F subcooling
according to Table 3, Required Liquid Line Temperature (°F) at Service Valve.
Required
Liquid Pressure (PSIG) at Service Valve
Subcooling
134 141 148 156 163 171 179 187 196 205 214 220 223 233 243 253 264 274 285 297 309 321 331 346 359
(°F)
0
5
10
15
20
25
76
71
66
61
56
51
79
74
69
64
59
54
82
77
72
67
62
57
85
80
75
70
65
60
88
83
78
73
68
63
91
86
81
76
71
66
94
89
84
79
74
69
97
92
87
82
77
72
100 103 106 108 109 112 115 118 121 124 127 130 133 136 139 142 145
95 98 101 103 104 107 110 113 116 119 122 125 128 131 134 137 140
90 93 96 98 99 102 105 108 111 117 120 123 126 129 129 132 135
85 88 91 93 94 97 100 103 106 109 112 115 118 121 124 127 130
80 83 86 88 89 92 95 98 101 104 107 110 113 116 119 122 125
75 78 81 83 84 87 90 93 96 99 102 105 108 111 114 117 120
Table 3. Required Liquid Line Temperature (°F) at Service Valve R-22
MVW water line connections
The MVW air conditioners have an internal condenser. The location of the water in and water
out connections are shown on the dimensional drawings in Appendix A. Size the water lines to
provide the minimum water flow rates shown in Table 4.
When connecting the water lines, hold the condenser inlet and outlet stubs firmly with a wrench
to prevent twisting. Observe all applicable codes.
Minimum Seawater Flow Rates
Model
MVW60
MVW90
MVW120
MVW144
MVW180
MVW240
Circuit
1
1
1
2
Total
1
2
Total
1
2
Total
1
2
Total
Gallon/Hour
Minimum
Maximum
600
1,050
900
1,578
600
1,050
600
1,050
1,200
2,100
600
1,050
900
1,578
1,500
2,628
900
1,578
900
1,578
1,800
3,156
1,200
2,100
1,200
2,100
2,400
4,200
Liters/Minute
Minimum
Maximum
38
66
57
100
38
66
38
66
76
132
38
66
57
100
95
166
57
100
57
100
114
199
76
132
76
132
151
265
Table 4. Minimum Seawater flow rates by Model
Proper water flow is absolutely critical to the operation of the air conditioner. If the pipe is too
small, back pressure is created causing a drop in water flow, even if the pump is correctly sized. If
Page 10 of 18
the piping is too large, the slow velocity of the water may cause silt build-up and barnacle growth
inside the piping, eventually restricting water flow.
The best material for sea water piping and fittings is cupronickel. Suitable materials for piping
are hi-grade bronze cupronickel and schedule 80 PVC pipe. Materials to avoid are yellow
brass, copper, poor grades of aluminum, stainless steel or steel pipe. Use Teflon® tape or other
appropriate sealant on all threaded fittings to prevent leaks.
Duct
Connect the duct or plenum to the flange on top to the units.
The duct system must be engineered to insure sufficient air flow. This includes proper duct
sizing and a sufficient number of supply registers. Duct must be firmly attached, secured and
sealed to prevent air leakage. When using insulated flexible duct, make sure that the inner duct
is secured and sealed to an adapter before pulling the insulation over the connection. Install the
supply grilles (if used) high on the cabin wall to create good air circulation. Insulate all transitions
and plenums. Stretch the duct tight in straight runs. Make bends and turns as large as possible.
Galvanized metal duct extensions may be used to simplify connections to duct work and grilles.
Use fabric boots to prevent transmission of vibration through the duct system. If the duct is in
storage or other high traffic areas, protect it from being crushed with a shield or box.
To prevent short cycling of the air conditioner, take care not to direct the conditioned air directly
onto the thermostat.
DANGER CARBON MONOXIDE POISONING
IF THE DUCT MUST BE RUN THROUGH AREAS CONTAINING ENGINES OR FOSSIL FUEL
DEVICES, IT IS ABSOLUTELY MANDATORY THAT THE DUCT SYSTEM BE AIR TIGHT TO
PREVENT CARBON MONOXIDE AND ANY OTHER HAZARDOUS GASES OR VAPORS FROM
BEING INTRODUCED INTO THE CONDITIONED AIR SYSTEM. SEE ABYC STANDARD “A-6
REFRIGERATION AND AIR CONDITIONING EQUIPMENT” FOR MORE INFORMATION ON
INSTALLING DUCT THROUGH THESE AREAS.
Condensate connection and disposal
The air conditioners will produce significant quantities of condensate in most marine applications
that may cause significant damage to the vessel if not disposed of properly. The condensate
openings on the units are from the right side. Always install a trap in the condensate line to ensure
proper drainage and to prevent condensate from overflowing the evaporator drain pan. Refer to
the drawings in Appendix A for the exact location of the condensate openings.
DANGER CARBON MONOXIDE POISONING
IF THE CONDENSATE LINE MUST BE RUN THROUGH AREAS CONTAINING ENGINES OR
FOSSIL FUEL DEVICES, IT IS ABSOLUTELY MANDATORY THAT THE LINE BE AIR TIGHT TO
PREVENT CARBON MONOXIDE AND ANY OTHER HAZARDOUS GASES OR VAPORS FROM
BEING INTRODUCED INTO THE CONDITIONED AIR SYSTEM. SEE ABYC STANDARD “A-6
REFRIGERATION AND AIR CONDITIONING EQUIPMENT” FOR MORE INFORMATION ON
INSTALLING A CONDENSATE LINE THROUGH THESE AREAS.
Page 11 of 18
4.2 Electrical Connection
WARNING ELECTRIC SHOCK HAZARD
FAILURE TO FOLLOW SAFETY WARNINGS EXACTLY COULD RESULT IN SERIOUS
INJURY, DEATH AND OR PROPERTY DAMAGE. TURN OFF ELECTRICAL POWER AT
SERVICE PANEL BEFORE MAKING ANY ELECTRICAL CONNECTIONS AND ENSURE
A PROPER GROUND CONNECTION IS MADE BEFORE CONNECTING LINE VOLTAGE.
All electrical work must meet the requirements of all applicable codes and ordinances. Work
should only be done by qualified persons.
If the wiring diagram that is on or was shipped with the unit is different from the one in this
manual, refer to and use the wiring diagram that is on or was shipped with the unit.
High Voltage Wiring
The MVS and MVW air conditioners are available for operation on a 208/230v. 3ø, 60 Hz.
or a 460v, 3ø, 60 Hz. Power supply. Refer to the data label on the air conditioner for field
requirements. The electrical data list fuse/HACR breaker and wiring size amps.
a) The power supply must have the proper voltage, phase and ampacity for the selected
model.
b) Refer to the data label on the unit for field wiring requirements. The electrical data lists
fuse and wire sizes for the unit.
c) Each unit has a Minimum Circuit Ampacity (MCA). Field wiring must be used that is
of sufficient size to carry that amount of current. Use copper conductors only. Refer to
the National Electrical Code for complete current carrying capacity data on the various
insulation grades of wiring materials.
d) Power supply must be within allowable range of ±10% of rated voltage.
e) The unit must be properly grounded to reduce the risk of shock or electrocution.
f) A properly sized circuit breaker must be used. Information required to size the breaker is on
the data sticker on the unit.
g) The breakers must be motor rated type B or, preferably type C.
h) Connections between the ship’s alternating current grounding conductor and the ship’s
negative or bonding system must be made as part of the ship’s wiring as per ABYC
standard E-11 or equivalent.
i) When servicing or replacing existing equipment that contains a chassis mounted ground
lug, the service person or installer must verify the ship’s wiring for the connection required
in item e & h. above.
j) All electrical connections must be made within the electrical junction boxes supplied
with the unit. A terminal strip and/or electrical connectors are provided for component
installation.
Page 12 of 18
IMPORTANT
Scroll compressors, like several other types of compressors, will only compress in one rotational
direction. The direction of rotation is not an issue with single-phase compressors since they will
always start and run in the proper direction. However, three phase compressors will rotate in
either direction depending upon phasing of power. Since there is a 50-50 chance of connecting
power in such a way as to cause rotation in the reverse direction, it is imperative to confirm
that the compressor is rotating in the proper direction at the initial field start-up of the system.
Verification of proper rotation is made by observing that the suction pressure drops and the
discharge pressure rises when the compressor is energized. An alternate method of verification
for self-contained system with small critical refrigerant charges, where the installation of gauges
may be objectionable, can be made by monitoring the temperature of the refrigerant lines at the
compressor. The temperature should rise on the discharge line while the suction
line temperature decreases. Reverse rotation also results in a substantially reduced current draw
when compared to tabulated values.
There is no negative impact on durability caused by operating three phase compressors in the
reversed direction for a short duration of time, usually defined as less than one hour. However,
after several minutes of operation the compressor’s internal protector will trip. The compressor
will then cycle on the protector until the phasing is corrected. Reverse operation for longer than
one hour may have a negative impact on the bearings.
1. Size the incoming power supply lines according to Code requirements. Run the power
conductors through the knockouts on the right side of the unit. Use appropriate conduit and
strain reliefs.
2. Connect the wires to the input side of the internal breaker or terminal block L1, L2, & L3
for three-phase models.
3. Install the ground wire on the ground lug.
4. For units designed for operation on 208/230V, 60Hz power supply, the transformer is
factory wired for a 230V power supply. For a 208V power supply, remove the orange lead
from the transformer and connect the red lead. Insulate the orange lead.
Page 13 of 18
Low Voltage (Control) Wiring
IMPORTANT
The following instructions are generic wiring instructions and may not be applicable for all
thermostats. Always refer to the wiring diagram in the air conditioner for the proper method to
wire your unit. The air conditioner uses an electronic thermostat mounted in the conditioned
space. The MVx60 and MVx90 have one compressor. A single stage cooling thermostat may be
used with these units. The MVx120 and MVx144 air conditioners have two compressors. For
optimal temperature control, a 2-stage cooling thermostat should be used with these units.
1. Pull the low voltage wiring (e.g., 18 gauge 4-conductor Class 2 thermostat wire) from the
air conditioner into the thermostat / sub base assembly. See Appendix B for connections to
various thermostats.
2. Mount the thermostat on the wall of the cabin. The thermostat should be located so that
the supply air from the unit does NOT blow directly on to the thermostat. Connect the
thermostat to the terminal block in the conditioner as shown in Appendix B.
Initial Start-Up & Shut Down
Chapter 5
Important: Be sure that the crankcase heater (if used) has been energized for at least 24 hours
before starting the unit(s). Double-check all electrical connections before applying power.
MVS & MVW air conditioners with scroll compressors running on 3Ø power must be checked
for proper rotation during the initial start-up. Please refer to Chapter 4 for determining if the
3Ø compressors are rotating correctly. Incorrect rotation can damage the compressor and is not
covered by the warranty.
Procedure:
1. Set the cooling set point temperature on the wall thermostat to a point higher than the cabin
temperature.
2. Set the thermostat system switch in the AUTO or COOL position. Nothing should operate at
this time.
3. Set the time delay on the control board in the control box to three minutes.
4. On MVW units (water source) turn on the condenser water supply. On MVS units, open the
refrigerant lines. Refer to 4.1 for recommended installation procedures.
5. Slowly lower the thermostat's cooling set point temperature until the switch closes. The indoor
fan should operate. Once the indoor fan turns on, allow approximately three minutes for the
compressor to start. On MVS units, verify operation of the condenser fans. The fans should be
running during compressor operation.
6. While the compressor is operating, check for proper phasing as described in Chapter 4.
7. To stop cooling, slowly raise the thermostat cooling set point to a temperature higher than the
ambient. If the unit fails to operate, refer to the troubleshooting information in Chapter 7.
8. Set thermostat for comfort as desired.
Page 14 of 18
NOTE: The fan purge allows the indoor fan to run for approximately 90 seconds after the
compressor is off.
Air Conditioner Shut Down
Turn thermostat’s selector switch to the OFF position. Do not shut off main power to the unit
except to service the air conditioner.
Winter Shut Down (MVW water cooled units only)
1. If the air conditioner may be exposed to freezing temperatures, drain the water from the
condenser and all water piping.
2. Pump a non-corrosive, potable anti-freeze solution throughout the system’s water supply and
discharge lines. Be sure to follow all state, local and federal ordinances if discharging the antifreeze solution overboard.
3. Run the air conditioner until a steady stream of anti-freeze solution is being discharged.
Chapter 6
Maintenance
Scheduled Maintenance
Marvair® strongly recommends that the air conditioner be serviced a minimum of twice a year. At
this time the filters, evaporator coil, condenser coil(s), the cabinet, and condensate drain should be
serviced as described below.
In addition to this seasonal check-out, the air conditioner should be maintained as follows:
Standard Air Filters
Replace the air filters whenever it is visibly dirty. Never operate the air conditioner without
the return air filters in place. If washable filters are used, flush with hot water or steam or soak
in a mild water solution with soap or detergent. Refer to filter manufacturer’s instructions as
necessary. Two inch filters are available for many units.
Model
60
90
120
144
180
240
Part
Number
92330
92334
92332
92334
92332
92332
92373
92334
92373
92334
Size
Unit Filters
(Inches)
15
20
16
20
16
16
20
20
20
20
x
x
x
x
x
x
x
x
x
x
20
25
25
25
25
25
20
25
20
25
x
x
x
x
x
x
x
x
x
x
1
1
1
1
1
1
1
1
1
1
MM
381
508
406
508
406
406
508
508
508
508
x
x
x
x
x
x
x
x
x
x
508
635
635
635
635
635
508
635
508
635
x
x
x
x
x
x
x
x
x
x
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
Table 5. Filter Sizes by Model
Qty
Total
2
2
1
2
1
4
4
4
4
4
2
3
3
4
8
8
Evaporator
If the evaporator becomes clogged or dirty, it may be cleaned by careful vacuuming or with a
Page 15 of 18
commercial evaporator cleaning spray. DO NOT use a solvent containing bleach, acetone, or
flammable substances. Turn off power before cleaning. Be careful not to wet any of the electrical
components. Be sure the unit has dried before restarting.
Use a fin comb of the correct tooth spacing to straighten mashed or bent fins.
Condenser
MVS units (air cooled). TURN OFF POWER BEFORE CLEANING! Be sure that all electrical
components are thoroughly dry before restoring power.
Periodically inspect the outdoor condenser for dirt or obstructions. Remove foreign objects such
as leaves, paper, etc. If the condenser coil is dirty, it may be washed off with a commercial solvent
intended for this purpose.
MVW units (water cooled). Verify that the unit has proper water flow. If insufficient water flow,
check any strainers and pumps for debris. If water flow still insufficient, descaling of the water
lines may be required.
Cabinet
The cabinet may be cleaned with a sponge and warm, soapy water or a mild detergent. Do not
use bleach, abrasive chemicals or harmful solvents.
Drains
Regularly check the condensate drain. An obstruction will force water to dump into the middle of
the unit and drain out the sides of the air conditioner, causing water on the floor.
Lubrication
Oiling of the the evaporator blower motor is not required as the motor is sealed and does not need
oiling
Chapter 7
Troubleshooting
Page 16 of 18
Chapter 8
Warranty
Marvair® Marine Warranty for Models MVS & MVW air conditioners
Parts
If any part of your Marvair unit fails because of a manufacturing defect within fifteen months
from the date of original shipment by Marvair of the air conditioner or within twelve months
from the date of start-up of the air conditioner, whichever is the earlier date, Marvair will furnish
without charge, EXW Cordele, Georgia, the required replacement part.
The responsibility of the Owner of the Equipment includes the following:
1. To operate the equipment according to the manufacturer's instructions.
2. To provide easy accessibility for service.
3. To check and reset circuit breaker(s) and disconnect before calling for service. (Circuit
breaker(s) may be in the main service panel.)
4. To keep the unit clean and free of dirt.
5. To clean and/or replace the filters as required.
6. To keep the evaporator coil clean and on MVW units to keep the condenser coil free of
sediment or scale. On MVS units, to keep the both the evaporator and condenser coils
clean.
7. To pay the charges incurred when any of the above have not been done.
8. To pay for repair or replacement of any material or part other than those within the Marvair
unit or thermostat itself.
9. To check any fuses on the circuit board and replace as required.
The owner of the product may ship the allegedly defective or malfunctioning product or part
to Marvair, at such owner’s expense, and Marvair will diagnose the defect and, if the defect is
covered under this warranty, Marvair will honor its warranty and furnish the required replacement
part. All costs for shipment and risk of loss during shipment of the product or part to Marvair
and back to the owner shall be the responsibility and liability of the owner. Upon request by
an owner, Marvair may arrange for remote diagnosis and repair of the allegedly defective or
malfunctioning product or part.
An owner requesting performance under this Warranty shall provide reasonable access to the
allegedly defective or malfunctioning product to Marvair and its authorized agents and employees.
This warranty does not cover damage caused by improper installation including any refrigerant
leaks in the tubing and fittings between the evaporator and condenser sections on split systems;
misuse of equipment; negligent servicing; damage due to use of the product for purposes other
than those for which it was designed; damage caused by natural disasters, power surges, lightning
and submersion; damage caused by unauthorized modifications; and damage caused by improper
wiring or power supply to the air conditioner including operating the unit with an undersized
generator or condenser.
Page 17 of 18
THIS WARRANTY AND SERVICE POLICY CONSTITUTE THE EXCLUSIVE REMEDY
OF ANY PURCHASER OF A MARVAIR AIR CONDITIONER AND IS IN LIEU OF
ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR USE, TO THE FULLEST EXTENT PERMITTED BY LAW. IN NO EVENT SHALL
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR USE
EXCEED THE TERMS OF THE APPLICABLE WARRANTY STATED ABOVE AND
MARVAIR SHALL HAVE NO OTHER OBLIGATION OR LIABILITY. IN NO EVENT
SHALL MARVAIR BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
OR MONETARY DAMAGES.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO
HAVE OTHER RIGHTS WHICH VARY FROM STATE-TO-STATE. Some states do not allow
limitations or exclusions, so the above limitations and exclusions may not apply to you.
Page 18 of 18
Appendix A - Dimensional Drawings
Dimensional Drawings - MVx60
Shipping Weights
Model
LBS
KG
MVS60
635
289
MVW60
640
291
Page A-1
Dimensional Drawings - MVx90/120
Shipping Weights
Model
LBS
KG
MVS90
785
357
MVW90
795
361
MVS120
945
430
MVW120
965
439
Page A-2
Dimensional Drawings - MVx180/240
Shipping Weights
Model
LBS
KG
MVS180
TBD
TBD
MVW180
TBD
TBD
MVS240
TBD
TBD
MVW240
TBD
TBD
Page A-3
Appendix B - Electrical Schematics
Electrical Schematics - MVS60 for 460v., 3ø, 60 Hz. Power Supply
Page B-1
Electrical Schematics - MVS120 for 460v., 3ø, 60 Hz. Power Supply
Page B-2
Electrical Schematics - MVW120 for 460v., 3ø, 60 Hz. Power Supply
Page B-3
Electrical Schematics - MVW180 & 240 for 460v., 3ø, 60 Hz. Power Supply
Page B-4
Appendix C - Start-Up Check List
A. Equipment Information
Marvair Air conditioner Compressor:
Compressor:
Condenser:
Model No.________________
Model No.________________
Model No.________________
Model No.________________
Serial No.________________
Serial No.________________
Serial No.________________
Serial No.________________
B. Pre-Start Up
Indoor Unit
Is there any shipping damage? (Y/N)_________
If so, where?_____________________________________________________________
________________________________________________________________________
Will this damage prevent starting the unit? (Y/N)_________
Check Power Supply, does it agree with data sticker on air conditioner? (Y/N)_________
Has the ground wire been connected? (Y/N)_________
Has the circuit protection been sized and installed properly? (Y/N)_________
Controls
MVS air cooled units only.
a) Has fan control for the remote condenser(s) been installed? (Y/N)_________
b) Do outdoor condenser fans operate when required? (Y/N)_________
Are thermostat and indoor blower control wiring connections made and checked?
(Y/N)_________
Are all wiring terminals (including main power supply) tight? (Y/N)_________
Has crankcase heater been energized for 24 hours? (Y/N)_________
Is control transformer wired for correct voltage? (Y/N)_________
Evaporator Section
Has water been placed in drain pan to confirm proper drainage? (Y/N)_________
Has trap been properly installed? (Y/N)_________
Are correct filters in place? (Y/N)_________
Page C-1
Water Piping (MVW water cooled units only)
Have water connections been checked? (Y/N)_________
Is water circulating pump operating properly? (Y/N)_________
Refrigerant Piping (MVS units only)
Have leak checks been made at the valves and all refrigerant connections, including,
solenoid valves, filter driers with a leak detector? (Y/N)_________
If leaks are found, repair and report any leaks. __________________________________
C. Check Voltage Imbalance
Line to Line Volts
AB_______V
AC________V
BC______V
(AB + AC + BC)/3 = Avg. Voltage = _______________
Max. deviation from avg. voltage = ______________volts
Voltage imbalance = (100 x Max. Deviation)/avg. Voltage = ___________%
If the voltage imbalance is greater than 2%, do not attempt to start the air conditioner!
Correct imbalance before starting the unit.
D. Check & Record Refrigerant Pressures
After 10 minutes of compressor operation, record the following:
Suction Pressure
Circuit 1
________
Circuit 2
_________
Suction Line Temperature
________
_________
Discharge Pressure
________
_________
Discharge Line Temperature
________
_________
Entering Condenser Air or Water Temp
________
_________
Leaving Condenser Air or Water Temp
________
_________
Evap. Entering Air DB Temp
________
_________
Evap. Entering Air WB Temp
________
_________
Evap. Leaving Air DB Temp
________
_________
Evap. Leaving Air WB Temp
________
_________
Compressor Amps (L1)
________
_________
________
_________
________
_________
Page C-2
Notes:
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
Page C-3

- Airxcel

Transcription

Similar documents

Brochure - Dunn Heating and Air Conditioning

sx 2300 air conditioner 13 seer

Atlantis Energy Systems Inc.

15,25,50 IBS! - Joshua Zeichner

Tempstar Residential Products

Aerosphere World Product Data Sheet

Coffing EC3 Manual

important - Beverage Air