Shelving Package Parmly Billings Library
Transcription
Shelving Package Parmly Billings Library
Parmly Billings Library 510 N Broadway Billings, Montana 59101 Shelving Package index: PART A: LIBRARY SHELVING Specifications List of Components Drawing A1 – Shelving End Panels Drawing A2 – Shelf Mounted Light Bracket Elevation Drawing A3 – Shelf Mounted Light Bracket Details Drawing A4 – Shelf Mounted Light Bracket Details Drawing A5 – Shelf Mounted Light Bracket Details Tabulation Form PART B: COMPACT MOBILE SHELVING Specifications List of Components Drawing B1 – CMS-01 Plan Drawing B2 – CMS-02 Plan Drawing B3 – Elevations Tabulation Form general notes: DRAWINGS Coded Shelving Plan – 11” x 17” (Not to Scale) Coded Shelving Plan – Scale: 1/8” = 1’-0” 1. Shelving Dealer to submit shop drawings and finish samples to Architect / Interior Designer for approval prior to fabrication. 2. Shelving Dealer is responsible for the provision, delivery and complete installation of all specified products and the removal of all packaging materials from the project site. 3. Shelving Dealer to coordinate the delivery and installation schedule with the Architect / Interior Designer and the access to the building with the General Contractor, who has full control of the project site. 10 may 2013 will bruder PARTNERS LTD + 2524 North 24th Street Phoenix, Arizona 85008 602 324 6000 fax 602 324 6001 www.willbruder.com Parmly Billings Library 510 N Broadway Billings, Montana 59101 Shelving Package PART A: LIBRARY SHELVING index: Specifications List of Components Drawing A1 – Shelving End Panels Drawing A2 – Shelf Mounted Light Bracket Elevation Drawing A3 – Shelf Mounted Light Bracket Details Drawing A4 – Shelf Mounted Light Bracket Details Drawing A5 – Shelf Mounted Light Bracket Details Tabulation Form will bruder PARTNERS LTD + 2524 North 24th Street Phoenix, Arizona 85008 602 324 6000 fax 602 324 6001 www.willbruder.com 10 may 2013 PARMLY BILLINGS LIBRARY PART A: LIBRARY SHELVING - SPECIFICATIONS Page 1 of 5 PART 1 – GENERAL: SCOPE: Work includes materials, delivery and installation of steel library shelving of the Starter/Adder and bracket type only. Furnish and install all shelving units as specified. SUBMITTALS: Product Data: Manufacturer’s descriptive literature shall be submitted, indicating materials, finishes, construction, and installation instructions and verifying that product meets requirements specified. Manufacturer’s recommendations for maintenance and cleaning shall be included. Shop Drawings: Submit installation plans and elevations of each type of shelving. Samples: Submit samples of paint finish (which will be used for actual production) and acrylic end panel material to the Architect / Interior Designer for verification and approval prior to ordering. QUALITY ASSURANCE: Warranty: Manufacturer’s standard form in which the manufacturer agrees to repair and/or replace shelving components for a period of five (5) years from the time of installation. Said warranty shall replace or repair any component that fails its intended use under normal usage and/or develops finish problems under standard use. Supplier: The manufacturer, subsidiary, or licensed agent shall be approved to supply the products specified, and to honor any claim against the product presented in accordance with the warranty. Vendor/Installer: The installer shall be affiliated directly with vendor. The installer shall be qualified to install the specified products by prior experience, demonstrated performance and acceptance of any requirement of manufacturer or any subsidiary or licensed agent. The installer shall be responsible for acceptable installation. References shall be provided to the Owner with Proposal Submission. DELIVERY, STORAGE, AND HANDLING: Product shall be delivered to the project site in manufacturer’s original packaging. Product shall be handled and stored to prevent damage to materials and finishes. SEISMIC: Billings, Montana is considered to be in a Seismic Design A designation. PARMLY BILLINGS LIBRARY PART A: LIBRARY SHELVING - SPECIFICATIONS Page 2 of 5 PART 2 – PRODUCTS: Burden of proof that proposed substitutions shall be equal in quality and function to the specified is on the offerer. 2.01- Quality Assurance A. Only the finest materials and quality of workmanship will be acceptable. Sheet metal is to be cold rolled, Class I steel. Gauge thickness shall be U.S. standard with the following minimum requirements: 1. 2. 3. 4. Upright Columns: #14 Gauge Top and Bottom Spreaders: #16 Gauge Shelves: (Including Base Shelf) #18 Gauge Shelf end Brackets: #16 Gauge B. All shelving shall be carefully adjusted to the floor and leveled. Wall shelving shall be attached to the walls at the most inconspicuous. 2.02 – Basis of Design Stack Shelving Steel book stacks shall be cantilever with Starter/Adder frame assemblies as manufactured by Estey/Tennsco Corporation, Dickson, TN. Weld frame unit construction is not acceptable. Commercial or case-type shelving will not be considered. Any bracing that prevents insertion of oversize material (past the center line) on any base or adjustable shelf is not acceptable. 2.03 – Approved Equals Manufacturers offering Starter/Adder Frame products that comply with the requirements shall meet or exceed specialized library shelving systems as manufactured by: 1. Estey/Tennsco PO Box 1888 Dickson, TN 37056 2. MJ Industries PO Box 259 Georgetown, MA 01833 3. Biblomodel Ocampo 167, Col. Las Encinas Escobedo, N.L. 66050 Mexico 4. BCI Eurobib 100 Hilltop Road Ramsey, NJ 07446 PARMLY BILLINGS LIBRARY PART A: LIBRARY SHELVING - SPECIFICATIONS Page 3 of 5 2.04 - Material Components Individual standard (cataloged) components to be as follows: A. Upright Columns are formed from no less than #14 gauge tubular steel. Overall dimensions are 2-1/2” in the web and 1-1/2” across the front and rear surfaces. Uprights are perforated the full height with a series of 5/16” x 5/8” slots spaced on 1” vertical centers and located ¾” of the outer web surface to the center of the slot. All slots are rectangular in shape to allow ease of installation and resting shelves. Every fifth and sixth slot has a rounded top for visual alignment of shelves. Side slots are located at the top, bottom, and middle of the upright with a special design allowing the strut to lock in place. Base supports are welded into place creating a single upright and base support assembly, with leveling bolts at each end of the base support. B. Top and Bottom Spreaders are formed of no less than #16 gauge steel in a channel shape, measuring 1-1/3” x 4-11/32” in cross section and attached to the uprights by means of pressure lock system and secure cover, insuring any possible walking of strut from the upright. C. Integral Back Adjustable Shelves are forged of no less than #18 gauge steel and support book loads of 50 pounds per square foot without deflection in excess of 3/16”. Nominal depth of shelf shall be 1” greater than the actual dimension measured from front of the shelf to frame upright. The front edge of the shelf to be box formed a minimum of 13/16” high to receive an under shelf, front edge mounted wire book support or snap-on label holder if required. The rear edge of the shelf shall be upturned a minimum of 2”. Side of shelf to be flanged for locking into end bracket grips. End brackets shall be no less than #16 gauge steel and extend at least 6” above the shelf surface. D. Shelf Accessories shall consist of 6” findable book supports and be made of not less than 18 gauge steel and include a non-skid composition cork base. E. Periodical/Newspaper Shelves shall be pivoting display shelves hinged to shelf brackets, which engage in slots in upright. Sloped display shelves are 14” actual height with 1-5/16” flange at the bottom and boxed flange upwards with an inside safety hem. Standard storage shelf is 12” deep nominal. Brackets allow for a slope of approximately 20 degrees from vertical. Newspaper sloping shelf shall include a hinged plexi-glass flap for paper security. All shelves to have integrated label holder. PARMLY BILLINGS LIBRARY PART A: LIBRARY SHELVING - SPECIFICATIONS Page 4 of 5 F. Media/AV Shelving shall consist of zigzag and browser style shelving. Browser shelves shall be no less than #16 gauge steel, 12”d x 6”h with 5-dividers and rubber non-skid mat. Zigzag shelves shall be no less than #16 gauge steel, 7”d x 8”h with 5integrated sections. G. Slotted/Adjustable Divider Shelves shall be slotted on 1” centers to accommodate dividers. They should include 5” backs, brackets, and (5) 9” dividers per shelf. H. Integrated Shelving Light Brackets shall consist of no less than #12 gauge steel. Lighting T-arm shall measure 5’-6” with each arm measuring 2’-9”w with the channel tapering from 2” at the upright to 1” at the end. The center post shall be an open channel and inserted into the top of the upright for ease of electrical wiring. *Refer to drawing. Light Fixtures and Electrical by General Contractor. 2.05 - Finishing Application All parts are thoroughly cleaned, neutralized and given a slight etch for adhesion. The final coat shall be epoxy powder applied by electrostatic method. The finish must yield a minimum average thickness of 1.0 to 1.8 mils and has a metallic finish. Abrasion resistance requires a minimum of 60 liters of sand to remove finish to bare metal and withstand rigid hammer and 180 degree fold test without flaking. 2.06 – Color Selection Paint Color shall be Pioneer Powder Coatings #HC32-2D6-M, AZ Satin Stainless Silver. Plastic upright plugs shall be grey. 2.07 – Basis of Design Acrylic End Panels Stacks end panels shall be Lumiclear Acrylic by Lumicor. The end panels should provide for resistance to UV degradation and be a renewable surface. Sheet thickness should be a minimum of 3/8” with a standard eased edge. The edges should be finished to a gloss. Product, color and finish shall be S022708 Lumiclear, Clear / .354”, 133469 Frost/Frost. Refer to drawing for panel sizes and attachment point locations. PARMLY BILLINGS LIBRARY PART A: LIBRARY SHELVING - SPECIFICATIONS Page 5 of 5 PART 3 – EXECUTION 3.01 – Installation A. Bookshelf Units: Install units at locations shown, in continuous ranges made up of The number of units shown, complying with the manufacturer’s instructions. Set units plumb and level, use non-corrosive metal shims as required. B. Anchor single faced ranges less than 12” deep and over 42” in height to the wall using manufacturers recommended method. C. Install adjustable shelves at equal spacing unless otherwise indicated. D. Vendor shall install product. Installation services shall not be brokered out. 3.02 – Adjustment and Cleaning Verify that moving parts are operating freely. Clean exposed surfaces and touch up marred finishes or replace components as necessary to eliminate evidence of deterioration. PARMLY BILLINGS LIBRARY PART A: LIBRARY SHELVING – LIST OF COMPONENTS Page 1 of 8 Code Manufacturer (Model/Model #) Location Quantity SH-01 Estey (Designer Series / See below for model numbers) Paperback Fiction / Double-Faced Bookstack Shelving Large Print Overall Dimensions: 36”w x 20”d x 88”h Base Shelves: 10”d Shelving: 10”d Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (49) 88”h x 20” Upright, #EDDUPT8810 (84) Connecting Struts, #DSTRUT36 (588) 10”d Integral back shelves, #DBLIB3610A (588) 6” Steel Book supports, #BSN6 (12) Light Brackets (14) EP-8: Acrylic End Panels, 89”h x 22”w (nominal) 42 SH-02 Estey (Designer Series / See below for model numbers) A/V Double-Faced Bookstack Shelving Overall Dimensions: 36”w x 66”h x 24”d Base Shelves: 12”d Browser Shelves: 12”d Zig-Zag Shelves: 7”d Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (63) 66”h x 24”d Uprights, #EDDUPT6612 (108) Connecting Struts, #DSTRUT36 (324) Browser Shelves, #BRS3611A (216) Zig-Zag Shelves, #DSDAV36 (108) 12” Integral back shelves, #DBLIB3612A (108) Steel Book Supports, #BSN6 (18) EP-5: Acrylic End Panels, 67”h x 26”w (nominal) 54 SH-03 Estey (Designer Series / See below for model numbers) New Books Double-Faced Bookstack Shelving Overall Dimensions: 36”w x 66”h x 20”d Base Shelves: 10”d Shelves: 10”d Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (20) 66”h x 20”d Uprights, #EDDUPT6610 (28) Connecting Struts, #DSTRUT36 (112) 10”d Integral back shelves, #DBLIB3610A (112) Steel Book Supports, #BSN6 (12) EP-4: Acrylic End Panels, 67”h x 22”w (nominal) 14 PARMLY BILLINGS LIBRARY PART A: LIBRARY SHELVING – LIST OF COMPONENTS Code Manufacturer (Model/Model #) Page 2 of 8 Location Quantity SH-04 Estey (Designer Series / See below for model numbers) Reserves Single-Faced Bookstack Shelving Overall Dimensions: 36”w x 88”h x 10”d Base Shelves: 10”d Shelves: 10”d Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (8) 88”h x 10”d Uprights, #EDSUPT8810 (14) Connecting Struts, #DSTRUT36 (42) 10”d x 36”w Integral back shelves, #DBLIB3610A (42) Steel Book Supports, #BSN6 (2) EP-7: Acrylic End Panels, 89”h x 12”w (nominal) 7 SH-05 Estey (Designer Series / See below for model numbers) Children’s Single-Faced Bookstack Shelving Workroom Overall Dimensions: 36”w x 88”h x 10”d Base Shelves: 10”d Shelves: 10”d Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (5) 88”h x 10”d Uprights, #EDSUPT8810 (8) Connecting Struts, #DSTRUT36 (30) 10”d x 36”w Integral back shelves, #DBLIB3610A (30) Steel Book Supports, #BSN6 4 SH-06a Estey (Designer Series / See below for model numbers) Easy Readers Double-Faced Bookstack Shelving Overall Dimensions: 36”w x 44”h x 20”d Base Shelves: 10”d Shelves: 10”d Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (29) 44”h x 20”d Uprights, #EDDUPT4410 (46) Connecting Struts, #DSTRUT36 (184) 10”d x 36”w Divider Shelves w/5 dividers, #DDS3610A (12) EP-2: Acrylic End Panels, 45”h x 22”w (nominal) 23 PARMLY BILLINGS LIBRARY PART A: LIBRARY SHELVING – LIST OF COMPONENTS Page 3 of 8 Code Manufacturer (Model/Model #) Location Quantity SH-06b Estey (Designer Series / See below for model numbers) Easy Readers Single Faced Bookstack Shelving Overall Dimensions: 36”w x 44”h x 10”d Base Shelves: 10”d Shelves: 10”d Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (7) 44”h x 10”d Uprights, #EDSUPT4410 (10) Connecting Struts, #DSTRUT36 (20) 10”d x 36”w Divider Shelves w/ 5 dividers, #DDS3610A (4) EP-1: Acrylic End Panels, 45”h x 12”d (nominal) 5 SH-07 Estey (Designer Series / See below for model numbers) Media Double-Faced Bookstack Shelving Overall Dimensions: 66”h x 36”w x 10”d Base Shelves: 10”d Shelves: 10”d Browser Shelves: 12”d Zig-zag Shelves: 7”d Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (20) 66”h x 36”w x 20”d Uprights, #EDDUPT6610 (36) Connecting Struts, #DSTRUT36 (36) 10”d x 36”w Integral back shelves, #DBLIB3610A (36) Steel Book Supports, #BSN6 (108) Zig-zag Shelves, #DSDAV36 (72) Browser Shelves, #BRS3611A (4) EP-4: Acrylic End Panels, 67”h x 22”w (nominal) 18 SH-08 Estey (Designer Series / See below for model numbers) Juvenile Double-Faced Bookstack Shelving South Overall Dimensions: 44”h x36”w x 20”d Base Shelves: 10”d Shelves: 10” d Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (20) 44”h x 20”d Uprights, #EDDUPT4410 (34) Connecting Struts, #DSTRUT36 (102) 10”d x 36”w Integral back shelves, #DBLIB3610A (102) Steel Book Supports, #BSN6 (6) EP-2: Acrylic End Panels, 45”h x 22”w, (nominal) 17 PARMLY BILLINGS LIBRARY PART A: LIBRARY SHELVING – LIST OF COMPONENTS Page 4 of 8 Code Manufacturer (Model/Model #) SH-09a Estey (Designer Series / See below for model numbers) Juvenile Double-Faced Bookstack Shelving North Overall Dimensions: 66”h x 36”w x 20”d Base Shelves: 10” Shelves: 10” Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (103) 66”h x 20”d Uprights, #EDDUPT6610 (170) Connecting Struts, #DSTRUT36 (850) 10”d x 36”w Integral back shelves, #DBLIB3610 (850) Steel Book Supports, #BSN6 (36) EP-4: Acrylic End Panels, 67”h x 22”w (nominal) 85 SH-09b Estey (Designer Series / See below for model numbers) Holiday Double-Faced Bookstack shelving Overall Dimensions: 66”h x 36”w x 20”d Base Shelves: 10” Shelves: 10” Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (21) 66”h x 20”d Uprights, #EDDUPT6610 (36) Connecting Struts, #DSTRUT36 (180) 10”d x 36”w Integral back shelves, #DBLIB3610 (180) Steel Book Supports, #BSN6 (6) EP-4: Acrylic End Panels, 67”h x 22”w (nominal) 18 SH-10a Location Estey (Designer Series / See below for model numbers) Juvenile Single-Faced Bookstack Shelving North Overall Dimensions: 66”h x 36”w x 10”d Base Shelves: 10” Shelves: 10” Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (32) 66”h x 10”d Uprights, #EDSUPT6610 (62) Connecting Struts, #DSTRUT36 (155) 10”d x 36”w Integral back shelves, #DBLIB3610A (155) Steel Book Supports, #BSN6 (2) EP-3: Acrylic End Panels, 67”h x 12”d (nominal) Quantity 31 PARMLY BILLINGS LIBRARY PART A: LIBRARY SHELVING – LIST OF COMPONENTS Page 5 of 8 Code Manufacturer (Model/Model #) Location Quantity SH-10b Estey (Designer Series / See below for model numbers) Juvenile Single-Faced Bookstack Shelving South Overall Dimensions: 66”h x 36”w x 10”d Base Shelves: 10” Shelves: 10” Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (10) 66”h x10”d Uprights, #EDSUPT6610 (18) Connecting Struts, #DSTRUT36 (45) 10”d x 36”w Integral back shelves, #DBLIB3610A (45) Steel Book Supports, #BSN6 (2) EP-3: Acrylic End Panels, 67”h x 12”d (nominal) 9 SH-11 Estey (Designer Series / See below for model numbers) Non-Fiction / Double-Faced Bookstack Shelving Teen Overall Dimensions: 88”h x 36”w x 20”d Base Shelves: 10” Shelves: 10” Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (277) 88”h x 20”d Uprights, #EDDUPT8810 (498) Connecting Struts, #DSTRUT36 (2652) 10”d x 36”w Integral back shelves, #DBLIB3610A (2652) Steel Book Supports, #BSN6 (84) Light Brackets (56) EP-8: Acrylic End Panels, 89”h x 22”w (nominal) 249 SH-12 Estey (Designer Series / See below for model numbers) Large Type Double-Faced Bookstack Shelving Overall Dimensions: 88”h x 36”w x 20”d Base Shelves: 10” Shelves: 10” Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (18) 88”h x 20”d Uprights, #EDDUPT8810 (32) Connecting Struts, #DSTRUT36 (192) 10”d x 36”w Integral Back Shelves, #DBLIB3610A (192) Steel Book Supports, #BSN6 (4) EP-8: Acrylic End Panels, 89”h x 22”w (nominal) 16 PARMLY BILLINGS LIBRARY PART A: LIBRARY SHELVING – LIST OF COMPONENTS Code Manufacturer (Model/Model #) Page 6 of 8 Location Quantity SH-13 Estey (Designer Series / See below for model numbers) Large Type / Double-Faced Bookstack Shelving Periodicals Overall Dimensions: 88”h x 36”w x 10/12”d Base Shelves: 10”/12” Shelves: 10” Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (18) 88”h x 24”d Uprights, #EDDUPT8812 (32) Connecting Struts, #DSTRUT36 (96) Periodical Shelving, #DPDS3612ACLH (96) 10”d x 36”w Integral Back Shelves, #DBLIB3610A (96) Steel Book Supports, #DSTRUT36 (9) Light Brackets (4) EP-9: Acrylic End Panels, 89”h x 24”w (nominal) 16 SH-14 Estey (Designer Series / See below for model numbers) Periodicals / Single-Faced Bookstack Shelving Newspapers Overall Dimensions: 78”h x 36”w x 12”d Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (16) 78”h x 12”d Uprights, EDSUPT7812 (46) Connecting Struts, #DSTRUT36 (25) Periodical Display w/plexi cover, #DPDSCA (40) Periodical Display Shelves, #DPDS3612ACLH (2) EP-6: Acrylic End Panels, 79”h x 14”w, (nominal) 13 SH-15a Estey (Designer Series / See below for model numbers) Reference Double-Faced Bookstack Shelving Overall Dimensions: 88”h x 36”w x 20d” Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (12) 88”h x 20”d Uprights, #EDDUPT8810 (18) Connecting Struts, #DSTRUT36 (108) 10”d x 36”w Integral Back Shelves, #DBLIB3610A (108) Steel Book Supports, #BSN6 (4) Light Brackets (4) EP-8: Acrylic End Panels, 89”h x 22”w, (nominal) 12 PARMLY BILLINGS LIBRARY PART A: LIBRARY SHELVING – LIST OF COMPONENTS Page 7 of 8 Code Manufacturer (Model/Model #) Location Quantity SH-15b Estey (Designer Series / See below for model numbers) Reference Single-Faced Bookstack Shelving Overall Dimensions: 88”h x 36”w x 10d” Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (4) 88”h x 10”d Uprights, #EDSUPT8810 (6) Connecting Struts, #DSTRUT36 (24) 10”d x 36”w Integral Back Shelves, #DBLIB3610A (24) Steel Book Supports, #BSN6 (2) EP-7: Acrylic End Panels, 89”h x 12”w, (nominal) 3 SH-16 Estey (Designer Series / See below for model numbers) Fiction Double-Faced Bookstack Shelving Overall Dimensions: 88”h x 36”w x 20”d Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (140) 88”h x 20”d Uprights, #EDDUPT3610 (238) Connecting Struts, #DSTRUT36 (1666) 10”d x 36”w Integral Back Shelves, #DBLIB3610A (1666) Steel Book Supports, #BSN6 (42) EP-8: Acrylic End Panels, 89”h x 22”w, (nominal) 119 SH-17 Estey (Designer Series / See below for model numbers) Montana Double-Faced Bookstack Shelving Room Overall Dimensions: 88”h x 36”w x 20”d Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (12) 88”h x 20”d Uprights, #EDDUPT3610 (20) Connecting Struts, #DSTRUT36 (120) 10”d x 36”w Integral Back Shelves, #DBLIB3610A (120) Steel Book Supports, #BSN6 (4) EP-8: Acrylic End Panels, 89”h x 22”w, (nominal) 10 SH-18 Estey (Designer Series / See below for model numbers) Genealogy Single-Faced Bookstack Shelving Overall Dimensions: 88”h x 36”w x 10”d Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (25) 88”h x 10”d Uprights, #EDSUPT8810 (40) Connecting Struts, #DSTRUT36 (120) 10”d x 36”w Integral Back Shelves, #DBLIB3610A (120) Steel Book Supports, #BSN6 (4) EP-7: Acrylic End Panels, 89”h x 12”w, (nominal) 20 PARMLY BILLINGS LIBRARY PART A: LIBRARY SHELVING – LIST OF COMPONENTS Page 8 of 8 Code Manufacturer (Model/Model #) Location SH-19 Estey (Designer Series / See below for model numbers) Digitizing Single-Faced Bookstack Shelving Overall Dimensions: 88”h x 36”w x 10”d Finish: Pioneer Paint #HC32-2D6-M, AZ Satin Stainless Silver Composition: (6) 88”h x 10”d Uprights, #EDSUPT8810 (10) Connecting Struts, #DSTRUT36 (35) 10”d x 36”w Integral Back Shelves, #DBLIB3610A (35) Steel Book Supports, #BSN6 (2) EP-7: Acrylic End Panels, 89”h x 12”w, (nominal) Quantity 5 PARMLY BILLINGS LIBRARY PART A: STEEL LIBRARY SHELVING - PROPOSER'S TABULATION FORM Code Quantity Shelving Quantity Light Brackets Quantity End Panels SH-01 42 12 14 SH-02 18 0 54 SH-03 14 0 12 SH-04 7 0 2 SH-05 4 0 0 SH-06a 23 0 12 SH-06b 5 0 4 SH-07 18 0 4 SH-08 17 0 6 SH-9a 85 0 36 SH-9b 18 0 6 SH-10a 31 0 2 SH-10b 9 0 2 SH-11 249 84 56 SH-12 16 0 4 SH-13 16 9 4 Shelving & Light Bracket Price Page 1 of 2 End Panel Price Total Price PARMLY BILLINGS LIBRARY PART A: STEEL LIBRARY SHELVING - PROPOSER'S TABULATION FORM Code Quantity Shelving Quantity Light Brackets Quantity End Panels SH-13 16 9 4 SH-14 13 0 2 SH-15a 9 4 6 SH-15b 3 0 2 SH-16 119 0 42 SH-17 10 0 4 SH-18 20 0 4 SH-19 5 0 2 Manufacturer: Shelving & Light Bracket Price Page 2 of 2 End Panel Price Subtotal: Model: Name of Company: (If Applicable) Freight: Authorized Signature: Installation: Date: Total Price: Total Price Parmly Billings Library 510 N Broadway Billings, Montana 59101 Shelving Package PART B: COMPACT MOBILE SHELVING index: Specifications List of Components Drawing B1 – CMS-01 Plan Drawing B2 – CMS-02 Plan Drawing B3 – Elevations Tabulation Form will bruder PARTNERS LTD + 2524 North 24th Street Phoenix, Arizona 85008 602 324 6000 fax 602 324 6001 www.willbruder.com 10 may 2013 PARMLY BILLINGS LIBRARY PART B: COMPACT MOBILE SHELVING - SPECIFICATIONS Page 1 of 6 PART 1 – GENERAL: SCOPE: Work includes materials, delivery and installation of two (2) Mechanically Assisted High Density Mobile Shelving Systems. Furnish and install all mobile carriages and shelving units as specified. SUBMITTALS: Product Data: Manufacturer’s descriptive literature shall be submitted, indicating materials, finishes, construction, and installation instructions and verifying that product meets requirements specified. Manufacturer’s recommendations for maintenance and cleaning shall be included. Shop Drawings: Submit installation plans and elevations of each type of shelving. Samples: Submit samples of paint finish for shelving units (which will be used for actual production) and plastic laminate for end panels to the Architect / Interior Designer for verification and approval prior to ordering. QUALITY ASSURANCE: Warranty: 5-YEAR LIMITED WARRANTY - Manufacturer warrants that all equipment, other than structural frames, shall be free from defects in materials and workmanship for five (5) years from the date of written acceptance of installation. Labor is included at no cost during the 1st year of the warranty period and will be charged at current rate thereafter. LIFETIME LIMITED WARRANTY – Manufacturer warrants that the mobile carriages (“structural frames”) will be free from defects in materials and workmanship for the lifetime of the structural frames. “Structural frames” exclude all moving parts, controls and guides that have immediate contact with any moving parts. Supplier: The manufacturer, subsidiary, or licensed agent shall be approved to supply the products specified, and to honor any claim against the product presented in accordance with the warranty. Vendor/Installer: The installer shall be affiliated directly with vendor and must be factory trained and certified. The installer shall be qualified to install the specified products by prior experience, demonstrated performance and acceptance of any requirement of manufacturer or any subsidiary or licensed agent. The installer shall be responsible for acceptable installation. References shall be provided to the Owner with Proposal Submission. DELIVERY, STORAGE, AND HANDLING: Product shall be delivered to the project site in manufacturer’s original packaging. Product shall be handled and stored to prevent damage to materials and finishes. SEISMIC Billings, Montana is considered to be in a Seismic Design A designation. PARMLY BILLINGS LIBRARY PART B: COMPACT MOBILE SHELVING - SPECIFICATIONS Page 2 of 6 PART 2 – PRODUCTS: Burden of proof that proposed substitutions shall be equal in quality and function to the specified is on the offerer. 2.01 – Quality Assurance A. B. Only the finest materials and quality of workmanship will be acceptable. Metal shall feature the strength of cold-rolled steel with gauge thickness that meets or exceeds U.S. Standards. Minimum requirements: 1. 4-POST SHELVING Closed Upright Posts – 18 Gauge “Closed” uprights closure panel between each post – 24 Gauge Shelf Supports – 14 gauge Shelf Reinforcements – 18 Gauge File Dividers - 18 Gauge Backstops for Single Faced File Dividers – 18 Gauge Centerstops for Double Faced File Dividers – 18 Gauge 2. MOBILE CARRIAGES Steel Carriage Side Profile – 12 Gauge Carriage Back to Back Supports – 12 Gauge Carriage Wheel Housing – 12 Gauge Stationary Platform – 12 Gauge. Stationary or fixed Platforms to be designed similar to Mobile Carriages and to be the same height, width, depth, and quality of Mobile Carriages. In Rail Anti-Tip Hooks – 8 Gauge Provide all necessary components to complete quality compact Mobile Shelving Systems. Items to be included but not limited to: 1. 4 POST SHELVING Closed Upright Angles Closed Upright “Tees” Low Profile Slotted Shelves Low Profile Plain Shelves (Canopy Tops) Shelf Supports Shelf Reinforcements Backstops Centerstops File Dividers Pull Out Reference Shelves Upright Wall Anchors for Stationary Ranges against walls Floor Anchors PARMLY BILLINGS LIBRARY PART B: COMPACT MOBILE SHELVING - SPECIFICATIONS 2. C. Page 3 of 6 MOBILE CARRIAGES B Rail End Stops B Anti Tip Rail with Channels and Necessary Grout In Rail Anti Tip Brackets that meet Seismic Seismic Design A designation L Floor & Ramp Dual Flange Line Shaft Mechanical Assist Carriages Stationary Platforms High Pressure Laminate End Panels Floor & Ramp Anchors Mobile Shelving Systems to be adjusted and leveled to existing floor. Rails to be laser leveled and laid out evenly so that moveable carriages will not drift or move on their own. Rail to be fully grouted along the entire length of the rail. No shims permitted. 2.02 – Basis of Design Compact Mobile Shelving System Mechanical assist compact mobile shelving system shall be Dual Flange Line Shaft High Density Mobile Shelving System with B Anti-Tip Rail as manufactured by Spacesaver Corporation, Fort Atkinson, WI. MOBILE SYSTEM DESCRIPTION A. General: The system consists of manufactured storage units mounted on manufacturer’s track-guided carriages to form a compact storage system. System design permits access to any single aisle by manually moving units until the desired aisle is opened. The carriage/rail system provides uniform carriage movement along the total length of travel, even with unbalanced loads. B. Carriage System Design and Features: The carriage system consists of a formed structural steel frame with machined and balanced wheels riding on steel rails surface mounted to the floor. Rails shall be B Anti Tip type to ensure smooth operation and self-centering of mobile storage units during travel without end play or binding. All bearings used in the drive mechanism shall be permanently shielded and lubricated. C. Movement Controls: Triple operating wheels (single arm handles not permitted) with rotating hand knobs shall be provided on the accessible (drive) ends of shelf units, centered on the end panel, located 40 inches from the base of each unit to permit units to be moved to create a single aisle opening. Turning the handle transmits power through chain drive to drive wheels on each carriage. D. Drive System: The system shall be designed with a positive type mechanically-assisted drive which minimizes end play, ensures there is no play in the drive handle, and that carriages will stop without drifting. 1. System shall include a chain sprocket drive system for each movable carriage to ensure that carriages move uniformly along the total length of travel, even with unbalanced loads. All system components shall be selected to ensure a smooth, even movement along the entire carriage length. Drive system gearing shall be PARMLY BILLINGS LIBRARY PART B: COMPACT MOBILE SHELVING - SPECIFICATIONS Page 4 of 6 designed to permit 1 lb. of force applied to the drive handle to move a minimum of 4,000 lbs. of load. E. F. 2. A tensioning device shall be provided on each chain drive with provision for adjusting tension without removing end panels. 3. All bearings used in the drive mechanism shall be permanently shielded and lubricated. Safety Features: 1. Color-coded visual indicators shall provide verification that carriages are in a locked or unlocked mode. 2. A single safety lock button, mounted on each operating wheel hub, will permit moving a carriage in either direction to create a new access aisle when pulled out (unlocked), or locking the carriage when pushed in. Finishes: 1. Fabricated Metal Components and Assemblies: Manufacturer’s standard powder coat paint finish. 4 POST SHELVING DESCRIPTION G. Design: 1. H. Wedge-lock type consisting of uprights, shelves, and shelf supports, designed to be assembled without fasteners or clips. Shelves shall not have any holes on exposed surfaces. Front and back flanges shall be flush with outside faces of posts. Design shall permit individual shelf adjustment and/or removal anywhere along the entire height of uprights. Materials and Workmanship: 1. Fabricate units from Class 1, cold-rolled steel sheet with all bends sharp and true and no exposed “knife” edges. a. All units shall be free of burrs, sharp edges and projecting hardware with smooth, non-abrasive surfaces and edges. b. After fabrication, shelving shall exhibit no dents, “oil canning”, buckling or other surface irregularities. I. Uprights: 1. Formed from steel sheet to a hollow “tee” shape for intermediate supports and formed angles for end supports. Uprights shall have keyhole slots on inner wall only. Provide with sheet steel panels full height and depth of end uprights. Provide intermediate “tee” uprights between adjacent units. All uprights to be “closed” uprights. PARMLY BILLINGS LIBRARY PART B: COMPACT MOBILE SHELVING - SPECIFICATIONS J. Shelves: 1. K. N. Form from heavy gauge steel sheet with four solid steel shoulder rivets, two per ear, that interlock with inner wall of uprights. Nominal Shelf Dimensions: 1. Standard Widths per drawings: Based on 6” increments 2. Shelf Edge Vertical Profile: 3/4 inch maximum. 3. Vertical Adjustment Increment: 1-1/2 inches. 4. Width Of Intermediate Uprights: 2 inches. 5. Clearance Between Uprights: Nominal shelf section width minus 2 inches. 6. Levelness of Completed Shelf Units: Maximum 1/8 inch between bottom shelf and canopy top, measured along the edge of any upright in any direction. 7. Number of Vertical Shelf Spaces per drawings. 8. Vertical Shelf-To-Shelf Spacing per drawings. Load Carrying Capabilities: 1. O. Same construction as shelf units. Shelf Supports: 1. M. Form from sheet steel with flanges on all sides and return them on front and back flanges. Ends shall be formed to clear inside of upright offset panels. Shelves shall be independently adjustable. Provide all shelves with slots for file dividers. Canopy Tops: 1. L. Page 5 of 6 Provide shelf units capable of supporting 40 pounds per lineal foot with maximum deflection of L/140. Shelves shall exhibit no permanent deflection under fully loaded conditions. Accessories: 1. File Dividers: Provide 2 file dividers per shelf. Provide manufacturer’s standard. 2. Center Stops: Provide manufacturer’s standard. 3. Back Stops: Provide manufacturer’s standard. 4. Reference Shelf: Provide manufacturer’s standard. See drawings for single faced or double faced locations, FABRICATION P. General: Coordinate fabrication and delivery to ensure no delay in progress of the Work. PARMLY BILLINGS LIBRARY PART B: COMPACT MOBILE SHELVING - SPECIFICATIONS Page 6 of 6 FINISHES Q. Paint Finish: Provide factory applied electrostatic powder coat paint in a smooth finish which meets or exceeds specifications. R. Paint Color: Selected from manufacturer’s standard available colors by Architect / Interior Designer. S. End Panels: Surface finish shall be high pressure plastic laminate selected from manufacturer’s standard available colors by Architect / Interior Designer. 2.03 – Approved Equals Manufacturers offering compact mobile shelving products that comply with the requirements shall meet or exceed compact mobile shelving systems as manufactured by: 1. Spacesaver Corporation 1450 Janesville Avenue Fort Atkinson, WI 53538 2. Montel, Inc. 225 4th Avenue Montmagny, QC Canada G5V 3S5 3. Tab US Headquarters 605 Fourth Street Mayville, WI 53050 PART 3 – EXECUTION: 3.01 – Installation A. Vendor shall install product. Installation services shall not be brokered out. B. Installation to be completed by a factory certified technician. C. Access to the building shall be coordinated with the General Contractor who has full control of the project site. D. Vendor shall be responsible for removal of all packaging material from the project site. E. Vendor to provide (2) cans of touch-up paint for future application. 3.02 – Adjustment and Cleaning Verify that moving parts are operating freely. Clean exposed surfaces and touch up marred finishes or replace components as necessary to eliminate evidence of deterioration. PARMLY BILLINGS LIBRARY PART B: COMPACT MOBILE SHELVING SYSTEM – LIST OF COMPONENTS Code Page 1 of 6 Manufacturer (Model/Model #) Basis of Design: Spacesaver Mechanical Assist Dual Flange Line Shaft High Density Mobile Shelving System with B Anti-Tip Rail CMS-01 Location: 114 Friend’s Workroom Spacesaver (DFMA Line Shaft Series): Overall Dimensions: 18’-2 3/4”w x 79”d x 83 1/16” h Shelves: 10”d single faced / 20” d double faced (10” each side divided by a centerstop) Shelving Finish: Manufacturer’s Standard Powder Coat Paint / Color to be selected End Panel Finish: Formica Plastic Laminate, Color: 1097-58, Citadel, Matte Finish Composition: Mobile (2) (38) (96) (19) (1) (8) (16) (1) (8) RE3 RL002 FF1L FR1L P2S06NN CDW2S06NA AT4 EHPL1296 EHPL2496 Composition: 4-Post and Case (2) US-1076-CA (16) US-2076-CA (1) US-1076-CT (8) US-2076-CT (2) SF-3610-P (16) SF-3620-P (12) SF-3610-S (96) SF-3620-S (216) SS-3614-F (36) SS-3614-HC (80) SR-20-F (16) SR-20-H (12) BS-36-F (96) CS-36-F (408) FD-0806 (1) RS-3310-S (8) RS-3320-D (3) UWA End Stop Kit Anti-Tip B Rail Rail – B Rail Anti-Tip Standard Floor – L Rail L Ramp Stationary Platform Line Shaft Mechanical Assist Carriage Anti-Tip Brackets Dual Flange In-Rail HPLF Panel HPLF Panel 4-Post Upright, Closed Angle 4-Post Upright, Closed Angle 4-Post Upright, Closed Tee 4-Post Upright, Closed Tee Low Profile Shelf, Plain Low Profile Shelf, Plain Low Profile Shelf, Slotted Low Profile Shelf, Slotted Shelf Support Shelf Support with Ears Cut Off Shelf Reinforcement Shelf Reinforcement Back Stop Center Stop File Divider Shelf Assembly – Reference, 4-Post Shelf Assembly – Reference, 4-Post Upright Wall Anchor PARMLY BILLINGS LIBRARY PART B: COMPACT MOBILE SHELVING SYSTEM – LIST OF COMPONENTS Page 2 of 6 CMS-01 System Description – Mechanical Assist High Density Mobile Shelving System Mobile shelving system should be designed to store library books and/or supplies related to the everyday operation of a standard public library. System should be designed per attached drawings and should have/include the following: (8) Mobile Double Faced Movable Carriages with 4-Post Shelving. Each carriage to have (2) 36” wide sections of 4-Post shelving. Each Carriage to be 20 ½” wide and have 20” deep shelving (10” useable each side). (1) Stationary Single Faced Shelving Range mounted on a Platform. A platform or fixed unit is similar to a carriage but without wheels and is made of the same material as a carriage. Shelving mounted to the platform is to be the exact height as shelving on moveable carriages. Stationary range to be 10 ½” wide and have 10” deep shelving. Stationary shelving range to have (2) 36” wide sections of 4-Post Shelving. Stationary Shelving range on platform to be mounted and anchored to the platform and be mounted to wall with wall mounting anchors for added rigidity. 2 Rail System – System to have (2) B Anti-tip Rails and are to extend under platforms and to be bolted to platforms for added rigidity. Rails to be laser leveled based on the levelness of the floor. Rails to be anchored to the floor and adhered to the floor using grout. The use of shims is not permitted. Seismic Anti-Tips to be attached from carriages to rails. Wood Deck and Ramp – A wood deck and ramp is to be installed under the carriage and in-between the rails. Wood deck and ramp to extend all the way across the length of the rails and underneath the stationary platform. System to have (1) Aisle – 33 3/4” wide (to be field verified) High Pressure Laminate End Panels to be on stationary shelving range and moveable carriages. 3-Spoke Ergonomic Handles to be located on each moveable carriage. Single spoke handles are not permitted. Rubber floor covering to be furnished and installed by General Contractor. Rubber roll goods shall be 3.2 mm thick. Assure that wood deck and ramp are manufactured to account for this thickness. Coordinate the installation of the rubber roll goods with the General Contractor. 4-Post Adjustable Shelving. Shelving to have standard 4-Post Shelving. Shelving to be adjustable vertically on 1 ½” increments. Shelving shall not require bolts, nuts, cross bracing, etc. to be assembled. Shelving upright angles and middle tees to be closed (not open). Each moveable carriage to have (2) 36” wide sections of shelving. PARMLY BILLINGS LIBRARY PART B: COMPACT MOBILE SHELVING SYSTEM – LIST OF COMPONENTS Page 3 of 6 Single Face Stationary range to have (2) 36” wide sections of shelving. Each section to have 6 levels of storage with minimum of 11 ¼” of clearance between each shelf. Some elevations to have 12 ¾” clearance. See drawing for details. Uprights to be 76 ¼” tall. Total system height to be no higher than 83 1/16” from the concrete floor to the top of the canopy tops on shelving. Single Faced shelving to be 10” deep and to have Backstops on each level. (2) adjustable File Dividers to be located on each shelf. File Dividers to be adjustable horizontally on 2” increments. Double Faced shelving to be 20” deep pass-thru shelving and to have Centerstops on each level. (2) adjustable File Dividers to be located on each side/shelf. File Dividers to be adjustable horizontally on 2” increments. System to have Pull Out Reference shelves located throughout the system. Pull Out Reference shelves to be located on the “3rd” opening of each shelving section and pull out similar to a work table. Each reference shelf able to hold a maximum of 50 lbs. System to have (1) single faced Reference Shelf located on single faced shelving range, and a total of 8 double faced Reference Shelves located on moveable carriages. (See drawings for locations). Capacity – System to have a total of 578 lineal filing feet of book/supply storage (6,936 lineal filing inches). PARMLY BILLINGS LIBRARY PART B: COMPACT MOBILE SHELVING SYSTEM – LIST OF COMPONENTS Code Page 4 of 6 Manufacturer (Model/Model #) Basis of Design: Spacesaver Mechanical Assist Dual Flange Line Shaft High Density Mobile Shelving System with B Anti-Tip Rail CMS-02 Location: 125 Outreach Services Spacesaver (DFMA Line Shaft Series): Overall Dimensions: 13’-9 1/2”w x 42 3/4”d (wall to outside handle) x 83 1/16” h Shelves: 10”d single faced / 20” d double faced (10” each side divided by a centerstop) Shelving Finish: Manufacturer’s Standard Powder Coat Paint / Color to be selected End Panel Finish: Formica Plastic Laminate, Color: 1097-58, Citadel, Matte Finish Composition: Mobile (28) (3) (39) (14) (2) (5) (10) (2) (5) RL002 RS1L FF1L FR1L P2S03NN CDW2S03NA AT4 EHPL1296 EHPL2496 Composition: 4-Post and Case (4) US-1076-CA (10) US-2076-CA (2) SF-3610-P (5) SF-3620-P (12) SF-3610-S (30) SF-3620-S (84) SS-3614-F (14) SS-3614-HC (25) SR-20-F (5) SR-20-H (12) BS-36-F (30) CS-36-F (144) FD-0806 (2) RS-3310-S (2) RS-3320-D (2) UWA Rail – B Rail Anti-Tip Standard L Rail Skirt Floor – L Rail L Ramp Stationary Platform Line Shaft Mechanical Assist Carriage Anti-Tip Brackets Dual Flange In-Rail HPLF Panel HPLF Panel 4-Post Upright, Closed Angle 4-Post Upright, Closed Angle Low Profile Shelf, Plain Low Profile Shelf, Plain Low Profile Shelf, Slotted Low Profile Shelf, Slotted Shelf Support Shelf Support with Ears Cut Off Shelf Reinforcement Shelf Reinforcement Back Stop Center Stop File Divider Shelf Assembly – Reference, 4-Post Shelf Assembly – Reference, 4-Post Upright Wall Anchor PARMLY BILLINGS LIBRARY PART B: COMPACT MOBILE SHELVING SYSTEM – LIST OF COMPONENTS Page 5 of 6 CMS-02 System Description – Mechanical Assist High Density Mobile Shelving System Mobile shelving system should be designed to store library books and/or supplies related to the everyday operation of a standard public library. System should be designed per attached drawings and should have/include the following: (5) Mobile Double Faced Movable Carriages with 4-Post Shelving. Each carriage to have (1) 36” wide sections of 4-Post shelving. Each Carriage to be 20 ½” wide and have 20” deep shelving (10” useable each side). (2) Stationary Single Faced Shelving Ranges mounted on Platforms. A platform or fixed unit is similar to a carriage but without wheels and is made of the same material as a carriage. Shelving mounted to the platform is to be the exact height as shelving on moveable carriages. Stationary ranges to be 10 ½” deep and have 10” deep shelving. Stationary shelving range to have (1) 36” wide sections of 4-Post Shelving. Stationary Shelving ranges on platforms to be mounted and anchored to the platform and be mounted to wall (left stationary unit) with wall mounting anchors for added rigidity. 2 Rail System – System to have (2) B Anti-tip Rails and are to extend under platforms and to be bolted to platforms for added rigidity. Rails to be laser leveled based on the levelness of the floor. Rails to be anchored to the floor and adhered to the floor using grout. The use of shims is not permitted. Seismic Anti-Tips to be attached from carriages to rails. Wood Deck and Ramp – A wood deck and ramp is to be installed under the carriage and in-between the rails. Wood deck and ramp to extend all the way across the length of the rails and underneath the stationary platform. System to have (1) Aisle – 36” wide (to be field verified) High Pressure Laminate End Panels to be on stationary shelving range and moveable carriages. 3-Spoke Ergonomic Handles to be located on each moveable carriage. Single spoke handles are not permitted. Rubber floor covering to be furnished and installed by General Contractor. Rubber roll goods shall be 3.2 mm thick. Assure that wood deck and ramp are manufactured to account for this thickness. Coordinate the installation of the rubber roll goods with the General Contractor. 4-Post Adjustable Shelving. Shelving to have standard 4-Post Shelving. Shelving to be adjustable vertically on 1 ½” increments. Shelving shall not require bolts, nuts, cross bracing, etc. to be assembled. Shelving upright angles and middle tees to be closed (not open). Each moveable carriage to have (1) 36” wide section of shelving. PARMLY BILLINGS LIBRARY PART B: COMPACT MOBILE SHELVING SYSTEM – LIST OF COMPONENTS Page 6 of 6 Single Face Stationary range to have (1) 36” wide section of shelving. Each section to have 6 levels of storage with minimum of 11 ¼” of clearance between each shelf. Some elevations to have 12 ¾” clearance. See drawing for details. Uprights to be 76 ¼” tall. Total system height to be no higher than 83 1/16” from the concrete floor to the top of the canopy tops on shelving. Single Faced shelving to be 10” deep and to have Backstops on each level. (2) adjustable File Dividers to be located on each shelf. File Dividers to be adjustable horizontally on 2” increments. Metal Back – A metal back that matches the color of the shelving to be located on back side of single faced stationary range located on the right side of the system. Rail Skirt – A rail skirt to be installed under far right platform to cover exposed rail, deck and ramp. Double Faced shelving to be 20” deep pass-thru shelving and to have Centerstops on each level. (2) adjustable File Dividers to be located on each side/shelf. File Dividers to be adjustable horizontally on 2” increments. System to have Pull Out Reference shelves located throughout the system. Pull Out Reference shelves to be located on the “3rd” opening of each shelving section and pull out similar to a work table. Each reference shelf able to hold a maximum of 50 lbs. System to have (2) single faced Reference Shelves located on single faced shelving ranges, and a total of 2 double faced Reference Shelves located on moveable carriages. (See drawings for locations). Capacity – System to have a total of 204 lineal filing feet of book/supply storage (2,448 lineal filing inches). PARMLY BILLINGS LIBRARY PART B: COMPACT MOBILE SHELVING - PROPOSER'S TABULATION FORM Code Quantity Single-Face Stationary Unit Quantity Double-Face Mobile Unit CMS-01 1 row of 2 units 8 rows of 16 units CMS-02 2 5 Manufacturer: Page 1 of 1 Price Subtotal: Model: Name of Company: (If Applicable) Freight: Authorized Signature: Installation: Date: Total Price:
Similar documents
A-Frame Display Shelving - Estey Library Solutions Tomorrow`s
Simply start with the A-Frame unit then choose from a variety of shelving options* to accommodate your needs. End panels are also available which hide any exposed hardware and create a finished loo...
More information