Kahler 2300, 2310, 2315, 2320 install

05/29/12 SUPERSEDES ALL PRIOR PRINTS
CODE: I-2300
2310
2315
2320
FOR TREMOLO
INSTALLATION INSTRUCTIONS
BRIDGES 2300, 2310, 2315, 2320
SIX STRING SERIES
OF (2) FRONT MOUNTING HOLES (USE CENTERLINE OF FRETBOARD).
X : LOCATION
SCALE LENGTH MEASUREMENT FOR CORRECT INTONATION IS FROM
CRITICAL CONTACT POINT (CCP) AT NUT AND TO THE CENTER OF
SADDLE TRAVEL (CST).
OF (2) REAR MOUNTING HOLES (USE CENTERLINE OF FRETBOARD)
Y: LOCATION
ALIGNMENT LEFT & RIGHT FOR CORRECT STRING LOCATION ON
FRETBOARD. (NOTE: L-R SADDLE ADJUSTMENTS ON BRIDGE).
"Y"
DIMENSION
"X" DIMENSION
CENTERLINE OF
FRETBOARD AT NUT
2.160
54.9
.150 FORWARD
SADDLE
3.8 ADJUSTMENT
1.000
25.4
1.475
37.5
2.950
74.9
1.160
29.5
REARMOST
.150 SADDLE
3.8 ADJUSTMENT
1.475
37.5
NUT
CRITICAL CONTACT
POINT AT NUT (CCP)
VERY CRITICAL MEASUREMENT
(MEASURE SCALE LENGTH PLUS1.930 FOR
CORRECT LOCATION OF REAR MOUNTING
SCREWS P/N 8371 #6 x 1.500 LG PH OVAL)
1.930
49.0
SCALE LENGTH
MEASUREMENT
CRITICAL CONTACT POINT AT SADDLE (CCP)
AT CENTER OF SADDLE TRAVEL (CST)
SCALE LENGTHS ARE VARIABLE
LUTHIER 100% RESPONSIBLE
DWG is to offer assistance to a
qualified Luthier. We do not
guarantee 100% satisfaction on this
DWG, therefore the Luthier is 100%
responsible for the
measurements and routings.
KAHLER INTERNATIONAL INC.
TITLE:
LOCATION MEASUREMENTS
ASSY: 2300, 2310, 2315, 2320
DWG. NO.
DRAWN:
TASC
6200RIMA
DATE:
03/213/11
SCALE:
1:1
KAHLER INTERNATIONAL, INC. Gateway Business Park, 1836 Ord Way, Oceanside, CA 92056 USA
Tel: (760)643-0000 Fax: (760)643-0074 www.kahlerparts.com [email protected]
SHEET 1 OF 3
07/24/12 SUPERSEDES ALL PRIOR PRINTS
CODE: I-2300
2310
2315
2320
LOCATION FOR ROUTING SHAPE AND DEPTH FOR
CORRECT CAM AND SPRING ACTION
CENTERLINE OF
FRETBOARD AT NUT
Z:1
Y
2.600
66.0
X
1.250
31.8
3.430
87.1
.500
12.7
.390
9.9
ROUTING OUTLINE
ROUTING LINE
BRIDGE MOUNTING PLATE
Z:2
Z
.850
21.6
X
.500
12.7
1.700
43.2
.600
15.2
2.300
58.4
Z:3
BRIDGE MOUNTING PLATE LOCATION AND
HEIGHT MEASUREMENT FOR CORRECT STRING ACTION
Z
X
BRIDGE MOUNTING
PLATE
.500±.020
TOP FACE OF GUITAR BODY
STRAIGHT EDGE ON
CENTERLINE OF FRETS.
SPAN AT LEAST 18 "
OF FRETBOARD
FRETS
FRET
BOARD
NOMINAL HEIGHT. IF GREATER, ADJUST NECK ANGLE OR ADD SHIMS
UNDER BRIDGE PLATE.
IF LESS, ADJUST NECK ANGLE OR ROUTE AN INSET.
DWG is to offer assistance to a
qualified Luthier. We do not
guarantee 100% satisfaction on
this DWG, therefore the Luthier
is 100% responsible for the
measurements and routings.
"A GUIDE ONLY"
KAHLER INTERNATIONAL INC.
TITLE:
ROUTING/FRET HT. MEASUREMENTS
ASSY: 2300, 2310, 2315, 2320
DWG. NO.
DRAWN:
TASC
6200RIMA
DATE:
03/21/11
SCALE:
1:1
KAHLER INTERNATIONAL, INC. Gateway Business Park, 1836 Ord Way, Oceanside, CA 92056 USA
Tel: (760)643-0000 Fax: (760)643-0074 www.kahlerparts.com [email protected]
SHEET 2 OF 2