Fluid-o-Tech magnet drive rotary vane pumps TM series

Fluid-o-Tech magnet drive rotary vane pumps TM series

Fluid-o-Tech magnet drive rotary vane pumps
TM series
connected to the rotor, and an outer magnet
connected to the motor shaft.
The pole-to-pole alignment of the two magnets
provides the driving motion to the pump.
Decoupling occurs when the pump load exceeds the
coupling torque between the magnets.
The introduction of a new driving magnet with
improved torque (available upon request) brings the
maximum operating pressure to the same values of
the PO series with direct coupling.
The Rotoflow TM series magnetic drive rotary vane
pumps are available in stainless steel
AISI 303 or brass, with carbon graphite internal
components.
21.5
(0.85 in)
Dimensions in mm/inches
3/8"GAS
3/8"NPT
Pump with standard bypass
88 (3.46 in)
88 (3.46 in)
29
(1.14 in)
Ø 78 (Ø 3.07 in)
45 (1.77 in)
+0.000
Ø 69.5 – 0.046
(+0.000)
(Ø 2.74 in) (– 0.0018)
3/8"GAS
3/8"NPT
Pump with balanced bypass
38 (1.5 in)
Ø 78 (Ø 3.07 in)
38 (1.5 in)
21.5 (0.85 in)
88 (3.46 in)
45 (1.77 in)
45 (1.77 in)
45 (1.77 in)
www.fluidotech.it
80 (3.15 in)
93-103 (3.66 - 4.06 in)
Ø 69.5 +0.000
– 0.046
(+0.000)
(Ø 2.74 in) (– 0.0018 in)
80 (3.15 in)
• Max system pressure: 18 bar (260 psi)
• Max temperature: 70 °C (158 °F)
29
(1.14 in)
The Fluid-o-Tech magnetic drive rotary vane pumps
combine the established range of pumps with the
added advantage of an indirect
magnetic coupling:
• longer service life
• no mechanical seals
• totally sealed body
• low maintenance
• less power consumption
• smooth transmission
The principle of the magnetic drive comprises
an inner magnet embodied in the pump and
Available upon request:
- 3/8” GAS or NPT threaded ports
- standard or balanced relief valve
- NBR, EPDM or Viton® seals
- NSF listed pumps for potable water
(TM...A series)
Dimensions in mm/inches
Bypass
Model
TMSS030
TMSS050
TMSS070
TMSS100
TMSS150
TMSS200
TMSS031
TMSS051
TMSS071
TMSS101
TMSS151
TMSS201
TMOT030
TMOT050
TMOT070
TMOT100
TMOT150
TMOT200
TMOT031
TMOT051
TMOT071
TMOT101
TMOT151
TMOT201
TMOT034
TMOT054
TMOT074
TMOT104
TMOT154
TMOT204
Housing
No
Stainless
Steel
Standard
No
Brass
Standard
Balanced
Figure
Flow Rate GPH l/h
300
A-A
B-B
C-C
D-D
E-E
F-F
A-A
B-B
C-C
D-D
E-E
F-F
A-A
B-B
C-C
D-D
E-E
F-F
A-A
B-B
C-C
D-D
E-E
F-F
A-A
B-B
C-C
D-D
E-E
F-F
70
250 F
60
200
50
40
100 C
0
2
Code
TM series pump
-
0
Flow Rate GPH l/h
300
2
4
6
50
8
100
10
150
14
16 BAR
200 225 PSI
12
1725 RPM
F
250
60
40
F
E
200
50
E
D
150
C
30
D
100 B
20
10
C
A
50
B
A
0
0
0
2
4
6
50
8
10
150
100
12
Flow Rate GPH l/h
600
TMBF56S
140
High torque mounting assembly (M56-B14)
TMBS56C
120
500 F
100
High torque mounting assembly (M63-B14)
TMBS63C
80
300
Standard mounting assembly (NEMA 56C)
TMBF5BS
60
200 C
High torque mounting assembly (NEMA 56C)
TMBS5BC
40
20
E
D
D
C
B
A
B
100 A
0
Pressure
Flow Rate
F
400 E
TMBF63S
Note: The “C” series driving magnets provide a slot in the internal bore to accept the driving
key of motors M56 and M63 frame.
0
0
0
2
4
50
6
8
100
10
150
12
F
500
80
60
0
E
400
D
300
D
C
C
200 B
100
0
Pressure
B
A
40
20
F
E
120
100
14
16 BAR
200 225 PSI
3500 RPM
GPH l/h
600
140
14
16 BAR
200 225 PSI
2900 RPM
Standard mounting assembly (M63-B14)
1
C
B
A
0
0
Pressure
Standard mounting assembly (M56-B14)
2
D
B
A
50
10
Pressure
Description
E
D
20
70
F
E
150
30
0
Pos
1
1450 RPM
0
0
A
2
4
50
6
8
100
10
150
12
14
16 BAR
200 225 PSI
curves with driving magnets TMAF09S, TMAF11S, TMAF5BS
curves with driving magnets TMAS09C, TMAS11C, TMAS5BC
Note: Hydraulic characteristics with water at 20 °C (68 °F) and without bypass. Use filter before pump inlet not larger than 10 microns. Pump weight: 1,1 kg (2,4 Lbs).
For applications involving other fluids, high temperatures, unusual processing conditions or speed higher than 2500 rpm consult the factory or an authorized distributor.
Fluid-o-Tech reserves the right to alter the specifications indicated in this catalogue at any time and without prior notice.
Fluid-o-Tech srl
Via Leonardo da Vinci, 40
20094 Corsico, Milano, Italy
Tel. +39 02 8917071
Fax +39 02 89170799
Fluid-o-Tech Int’l Inc.
161 Atwater St.,
Plantsville CT (USA) 06479
Tel. +1 (860) 276-9270
Fax +1 (860) 620-0193
Fluid-o-Tech Int’l Inc. Japan
203, 2-17-19, Ebara, Shinagawa
Tokyo 142-0063, Japan
Tel. +81 (0) (3) 3783-9660
Fax +81 (0) (3) 3783-9661
TM en – 11/10 Ed
Fluid-o-Tech Asia (Beijing) Co., Ltd
Jingwei Industrial Zone,
Beifang Huairou, Beijing, 101400, PRC
Tel. +86 (0) (10) 61684650
Fax +86 (0) (10) 61684651