Data Sheets TP-GE-F6

TurbinePROs
Data Sheets
for
GE Frame 6 Gas Turbine
© 2011 TurbinePROs
This document contains confidential technical data proprietary to TurbinePROs LLC. The drawings and all other
disclosures in this document are the property of TurbinePROs LLC. Unauthorized use, copying, distribution to third
parties, or reproduction in whole or part is prohibited.
Page TP-1
TP-GE-F6
ORIGINAL ISSUE:
Apr 27/11
REVISION:
Apr 27/11
Data Sheets
LIST OF DATA SHEETS
CLEARANCES
MS 6571-B BOLT TORQUING – FUEL NOZZLE PIPING
MS 6571-B BOLT TORQUING – CAN TO DISCHARGE
MS 6571-B BOLT TORQUING – X-FIRE FLANGES
MS 6571-B BOLT TORQUING – FLAME SCANNER FLANGES, NON-DLN
MS 6571-B BOLT TORQUING – SPARK PLUG
MS 6571-B BOLT TORQUING – CAN DOORS
FLOW SLEEVE GENERAL CONDITION – MS5002 AND 6001B
GAS FUEL NOZZLE (DLN) – MS6001 (SHEET 1 OF 3)
GAS FUEL NOZZLE (DLN) – MS6001 (SHEET 2 OF 3)
GAS FUEL NOZZLE (DLN) – MS6001 (SHEET 3)
LINER DISTORTION – MS6001B AND 9001F
COMBUSTION LINERS (DEFECTS) – MS6001B DLN
COMBUSTION LINER GENERAL CONDITION – MS6001B
SPARK PLUG BALL JOINT – DLN-1
TRANSITION PIECE GENERAL CONDITION –
MS6001B (SHEET 1 OF 2)
TRANSITION PIECE GENERAL CONDITION – MS6001B (SHEET 2)
ACCESSORY COUPLING FRAME – MS6001B (SHEET 1 OF 2)
ACCESSORY COUPLING FRAME – MS6001B (SHEET 2)
LOAD COUPLING – MS6001B
1ST STAGE BUCKETS GENERAL CONDITION – MS6001B (SHEET 1 OF 4)
1ST STAGE BUCKETS CORRELATION SHEET – MS6001 (SHEET 2 OF 4)
1ST STAGE BUCKETS CORRELATION SHEET – MS6001 (SHEET 3 OF 4)
1ST STAGE BUCKETS CORRELATION SHEET – MS6001 (SHEET 4)
2ND STAGE BUCKETS GENERAL CONDITION – MS6001B (SHEET 1 OF 4)
2ND STAGE BUCKETS GENERAL CONDITION – MS6001B (SHEET 2 OF 4)
2ND STAGE BUCKETS GENERAL CONDITION – MS6001B (SHEET 3 OF 4)
2ND STAGE BUCKETS GENERAL CONDITION – MS6001B (SHEET 4)
3RD STAGE BUCKETS GENERAL CONDITION – MS6001B & 9001E (SHEET 1 OF 4)
3RD STAGE BUCKETS GGENERAL CONDITION – MS6001B & 9001E (SHEET 2 OF 4)
3RD STAGE BUCKETS GENERAL CONDITION – MS6001B & 9001E (SHEET 3 OF 4)
3RD STAGE BUCKETS gENERAL CONDITION – MS6001B & 9001E (SHEET 4)
1ST STAGE SHROUDS GENERAL CONDITION – MS6001B
COMBUSTION CANS GENERAL – MS5001, 6001B, & 7001E
TP-GE-F6
Page 1
Apr 27/11
Data Sheets
CROSS FIRE TUBE GENERAL CONDITION – MS6001B
CROSS FIRE TUBE RETAINER GENERAL CONDITION – MS6001B
CROSS FIRE TUBE GENERAL CONDITION – MS6001 DLN
CROSS FIRE TUBE RETAINER GENERAL CONDITION – MS6001 DLN
1ST STAGE TURBINE CLEARANCES – MS6001B
2ND STAGE TURBINE CLEARANCES – MS6001B
3RD STAGE TURBINE CLEARANCES – MS6001B
NOZZLE TURBINE CLEARANCES – MS6001B
ACCESSORY & LOAD COUPLING – MS3002, 5001, 5002, 6001B, 7001E, & 9001E
ALIGNMENT SUPPORTS – MS5001 & 6001B
BEARING & SEAL CLEARANCES, NO. 1 – MS6001B (SHEET 1 OF 3)
BEARING & SEAL CLEARANCES, NO. 1 – MS6001B (SHEET 2 OF 3)
BEARING & SEAL CLEARANCES, NO. 1 – MS6001B (SHEET 3)
BEARING & SEAL CLEARANCES, NO. 2 – MS6001B (SHEET 1 OF 2)
BEARING & SEAL CLEARANCES, NO. 2 – MS6001B (SHEET 2)
JOURNAL BEARING (GENERAL CONDITION) – MS3002, 5001/2, 6001B, 7001E/F, & 9001E/F (SHEET
1 OF 2)
JOURNAL BEARING (GENERAL CONDITION) – MS3002, 5001/2, 6001B, 7001E/F, & 9001E/F (SHEET
2)
SLEEVE JOURNAL BEARING NO. 1 – MS5001, 6001B (SHEET 1 OF 2)
SLEEVE JOURNAL BEARING NO. 1 – MS5001, 6001B (SHEET 2)
OIL DEFLECTOR (ALIGNMENT) – MS3002, 5001, 5002, 6001B, 7001E/F, & 9001E/F
ROTOR JOURNAL CONDITION – MS3002, 5001/2, 6001B, 7001E/F, & 9001E/F
TILTING PAD THRUST BEARINGS KINGSBURY – MS6001B
ROTOR CLEARANCES - MS6001B
V.I.G.V. GENERAL CONDITION – MS5002, 6001B, & F (SHEET 1 OF 3)
VARIABLE INLET GUIDE VANES GENERAL CONDITION – MS5002, 6001B, & F (SHEET 2 OF 3)
VARIABLE INLET GUIDE VANES GENERAL CONDITION – MS5002, 6001B, & F (SHEET 3)
2ND STAGE SHROUDS GENERAL CONDITION – MS6001B
2ND STAGE DIAPHRAGM SEALS – MS6001B & 9001E (SHEET 1 OF 2)
2ND STAGE DIAPHRAGM SEALS – MS6001B & 9001E (SHEET 2)
3RD STAGE DIAPHRAGM SEALS – MS6001B (SHEET 1 OF 2)
3RD STAGE DIAPHRAGM SEALS – MS6001B (SHEET 2)
NOZZLE, ELLIPTICITY, & RADIAL CONCENTRICITY CHECKS 1ST STAGE – MS6001B
NOZZLE, ELLIPTICITY 1ST STAGE – MS3002, 5001/2, 6001B, 7001E/F, & 9001E/F (SHEET 1 OF 2)
NOZZLE, ELLIPTICITY 1ST STAGE – MS3002, 5001/2, 6001B, 7001E/F, & 9001E/F (SHEET 2)
2ND STAGE NOZZLE CONDITION – MS5001, 6001 B/F
TP-GE-F6
Page 2
Apr 27/11
Data Sheets
NOZZLE GENERAL CONDITION, 3RD STAGE – MS6001 B/F
1ST STAGE NOZZLE PARTITIONS – MS6001, 7001E, & 9001E (SHEET 1 OF 8)
1ST STAGE NOZZLE PARTITIONS – MS6001, 7001E, & 9001E (SHEET 2 OF 8)
1ST STAGE NOZZLE PARTITIONS – MS6001, 7001E, & 9001E (SHEET 3 OF 8)
1ST STAGE NOZZLE PARTITIONS – MS6001, 7001E, & 9001E (SHEET 4 OF 8)
1ST STAGE NOZZLE PARTITIONS – MS6001, 7001E, & 9001E (SHEET 5 OF 8)
1ST STAGE NOZZLE PARTITIONS – MS6001, 7001E, & 9001E (SHEET 6 OF 8)
1ST STAGE NOZZLE PARTITIONS – MS6001, 7001E, & 9001E (SHEET 7 OF 8)
1ST STAGE NOZZLE PARTITIONS – MS6001, 7001E, & 9001E (SHEET 8)
2ND STAGE NOZZLE PARTITIONS – MS6001 & 9001E (SHEET 1 OF 10)
2ND STAGE NOZZLE PARTITIONS – MS6001 & 9001E (SHEET 2 OF 10)
2ND STAGE NOZZLE PARTITIONS – MS6001 & 9001E (SHEET 3 OF 10)
2ND STAGE NOZZLE PARTITIONS – MS6001 & 9001E (SHEET 4 OF 10)
2ND STAGE NOZZLE PARTITIONS – MS6001 & 9001E (SHEET 5 OF 10)
2ND STAGE NOZZLE PARTITIONS – MS6001 & 9001E (SHEET 6 OF 10)
2ND STAGE NOZZLE PARTITIONS – MS6001 & 9001E (SHEET 7 OF 10)
2ND STAGE NOZZLE PARTITIONS – MS6001 & 9001E (SHEET 8 OF 10)
2ND STAGE NOZZLE PARTITIONS – MS6001 & 9001E (SHEET 9 OF 10)
2ND STAGE NOZZLE PARTITIONS – MS6001 & 9001E (SHEET 10)
3RD STAGE NOZZLE PARTITIONS – MS6001B & 9001E (SHEET 1 OF 10)
3RD STAGE NOZZLE PARTITIONS – MS6001 & 9001E (SHEET 2 OF 10)
3RD STAGE NOZZLE PARTITIONS – MS6001B & 9001E (SHEET 3 OF 10)
3RD STAGE NOZZLE PARTITIONS – MS6001 (SHEET 4 OF 10)
3RD STAGE NOZZLE PARTITIONS – MS6001 (SHEET 5 OF 10)
3RD STAGE NOZZLE PARTITIONS – MS6001 (SHEET 6 OF 10)
3RD STAGE NOZZLE PARTITIONS – MS6001 (SHEET 7 OF 10)
3RD STAGE NOZZLE PARTITIONS – MS6001 (SHEET 8 OF 10)
3RD STAGE NOZZLE PARTITIONS – MS6001 (SHEET 9 OF 10)
3RD STAGE NOZZLE PARTITIONS – MS6001 (SHEET 10)
SUPPORT RING GENERAL CONDITION – MS6001B
TP-GE-F6
Page 3
Apr 27/11
Data Sheets
MS 6571-B BOLT TORQUING – FUEL NOZZLE PIPING
NOZZLE NO.:
ITEM
DESCRIPTION
QUANTITY
PART NO.
SIZE
LENGTH
T.P.I.
TORQUE
A & B
C & D
GASKETS ANTI‐SEIZE BOLT BOLT CORRECTLY ON DIRECTION LENGTH NUT SIZE ALIGNED + FITTED
THREADS CONSISTENT CONSISTENT CONSISTENT PARALLEL TORQUE
INITIAL
Flange A
Flange B
Flange C
Flange D
NOTE: All bolts should point in the direction of flow.
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
MS 6571-B BOLT TORQUING – CAN TO DISCHARGE
CAN NO.:
ITEM
DESCRIPTION
QUANTITY
PART NO.
SIZE
LENGTH
T.P.I.
TORQUE
1
SIGNATURE
SIGNATURE
Gasket Fitted
Anti‐Seize on Threads
TORQUE
SIGNATURE
TORQUE
Bolt No. 1
Bolt No. 11
Bolt No. 2
Bolt No. 12
Bolt No. 3
Bolt No. 13
Bolt No. 4
Bolt No. 14
Bolt No. 5
Bolt No. 15
Bolt No. 6
Bolt No. 16
Bolt No. 7
Bolt No. 17
Bolt No. 8
Bolt No. 18
Bolt No. 9
Bolt No. 19
Bolt No. 10
Bolt No. 20
SIGNATURE
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
MS 6571-B BOLT TORQUING – X-FIRE FLANGES
TUBE NO.: ITEM
DESCRIPTION
QUANTITY
TO TUBE NO.: PART NO.
SIZE
LENGTH
T.P.I.
GAP
LHS
RHS
SIGNATURE
SIGNATURE
Gasket Fitted
Anti‐Seize on Threads
L.H.S
GAP
R.H.S
SIGNATURE
GAP
P1
P1
P2
P2
P3
P3
P4
P4
SIGNATURE
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
MS 6571-B BOLT TORQUING – FLAME SCANNER
FLANGES, NON-DLN
ITEM
DESCRIPTION
QUANTITY
PART NO.
SIZE
LENGTH
T.P.I.
TORQUE
1
FLANGE
GASKETS ANTI‐SEIZE CORRECTLY ON FITTED
THREADS BOLT 1
BOLT 2
BOLT 3
BOLT 4
TORQUE
SIGNATURE
Scanner 2
Scanner 3
Scanner 7
Scanner 8
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
MS 6571-B BOLT TORQUING – SPARK PLUG
ITEM
DESCRIPTION
QUANTITY
PART NO.
SIZE
LENGTH
T.P.I.
TORQUE
1
FLANGE
GASKETS ANTI‐SEIZE CORRECTLY ON FITTED
THREADS BOLT 1
BOLT 2
BOLT 3
BOLT 4
TORQUE
SIGNATURE
Spark Plug 1
Spark Plug 10
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
MS 6571-B BOLT TORQUING – CAN DOORS
CAN NO.:
ITEM
DESCRIPTION
QUANTITY
PART NO.
SIZE
LENGTH
T.P.I.
TORQUE
1
SIGNATURE
SIGNATURE
Gasket Fitted
Anti‐Seize on Threads
TORQUE
SIGNATURE
TORQUE
Bolt No. 1
Bolt No. 13
Bolt No. 2
Bolt No. 14
Bolt No. 3
Bolt No. 15
Bolt No. 4
Bolt No. 16
Bolt No. 5
Bolt No. 17
Bolt No. 6
Bolt No. 18
Bolt No. 7
Bolt No. 19
Bolt No. 8
Bolt No.20
Bolt No. 9
Bolt No. 21
Bolt No. 10
Bolt No. 22
Bolt No. 11
Bolt No. 23
Bolt No. 12
Bolt No. 24
SIGNATURE
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
FLOW SLEEVE GENERAL CONDITION – MS5002 AND 6001B
FORWARD FLOW SLEEVE:
S. NO. OUT
AFT FLOW SLEEVE:
S. NO. IN
CONDITION
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
GAS FUEL NOZZLE (DLN) – MS6001 (SHEET 1 OF 3)
CHAMBER NO.
FUEL NOZZLE
CLASSIFICATION
GAS
RTS
Returned to Service
DISTILLATE
R
Repaired
DUAL FUEL
RR
Replaced
PRIMARY
NOZZLE POSITION
SERIAL NUMBER
1
Mark with an X if nozzle is okay.
2
Mark with an X if nozzle is okay.
CONDITION OF PARTS
CLASSIFICATION
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
GAS FUEL NOZZLE (DLN) – MS6001 (SHEET 2 OF 3)
PRIMARY
NOZZLE POSITION
SERIAL NUMBER
3
Mark with an X if nozzle is okay.
4
Mark with an X if nozzle is okay.
5
Mark with an X if nozzle is okay.
6
Mark with an X if nozzle is okay.
CONDITION OF PARTS
CLASSIFICATION
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
GAS FUEL NOZZLE (DLN) – MS6001 (SHEET 3)
CHAMBER NO.
FUEL NOZZLE
CLASSIFICATION
GAS
RTS
Returned to Service
DISTILLATE
R
Repaired
DUAL FUEL
RR
Replaced
SERIAL NUMBER
CONDITION OF FUEL NOZZLE
CLASSIFICATION
SECONDARY AND TERTIARY Mark with an X if FUEL nozzle is okay.
NOZZLES
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
LINER DISTORTION – MS6001B AND 9001F
FORWARD END
LINER
D1
DIFFERENCE
D2
D1/D2
1
2
3
4
5
6
7
8
9
10
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
COMBUSTION LINERS (DEFECTS) – MS6001B DLN
COMBUSTION LINER NO.:
LINER PORT TYPE (MARK WITH AN X)
5 TYPE
6 TYPE
SERIAL NUMBER
LINER BODY CONDITION
Out
In
X If Condition is OK
Hula Skirt
X‐Fire Holes
Fuel Nozzle Port Condition
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
COMBUSTION LINER GENERAL CONDITION – MS6001B
COMBUSTION LINER NO.:
SERIAL NUMBER
LINER BODY CONDITION
HULA SKIRT
X‐FIRE HOLES
Out
In
X If Condition is OK
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
SPARK PLUG BALL JOINT – DLN-1
CLASSIFICATION
RTS
DEFECT CODES
Return to Service
W
Wear
R
Renew
CR
Cracked
RR
Repair
BT
Bent
BU
Burned
H
Hot Spots
SPARK PLUG POSITION
CONDITION
CLASSIFICATION
DEFECT
Chamber 1
Chamber 10
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
TRANSITION PIECE GENERAL CONDITION –
MS6001B (SHEET 1 OF 2)
TRANSITION NO.:
CHAMBER
S. NO. OUT
S. NO. IN
DESCRIPTION OF DEFECT
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
TRANSITION PIECE GENERAL CONDITION –
MS6001B (SHEET 2)
SLOT FRAME THICKNESS
TRANSITION OPERATING PIECE
HOURS
HL
HC
HR
AFT A
AFT B
AFT C
AFT D
Forward A
Forward B
Forward C
Forward D
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
ACCESSORY COUPLING FRAME – MS6001B (SHEET 1 OF 2)
COUPLING TYPE – MARK WITH AN X
DIMENSIONAL CHECKS
Oil Filled
OPENING
Grease Filled
End Float
Cont. Lubricated
Radial Clearances
CLOSING
Turbine End
Load Gear End
COUPLING RUNOUT
OPENING CHECK
Top
Left
Bottom
CLOSING CHECK
Right
Top
Left
Bottom
Right
Turbine End Hub
Midspan
Load Gear End Hub
TEETH CONDITION
GEAR END
TURBINE END
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
ACCESSORY COUPLING FRAME – MS6001B (SHEET 2)
CONDITION OF LUBRICANT
GEAR END
TURBINE END
DISPOSITION OF COUPLING – MARK WITH AN X
Returned to Service
Replaced
Repaired
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
LOAD COUPLING – MS6001B
NOTE: Runout reading to be taken on the uncoupled side when the other side of the coupling is finally assembled.
COUPLING INTERFERANCE FIT DIMENSIONS
TURBINE END
LOAD
GENERATOR END
TURBINE END
Male Dimension
Rim A
GENERATOR END
Rim B
Rim C
Rim D
Female Dimension
Fit
LOAD COUPLING ELONGATION DATA
TURBINE END
BOLT NO.
GENERATOR END
BOLT LENGTH
Initial
Final
BOLT LENGTH
Recheck ELONGATION
Initial
Final
Recheck ELONGATION
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
1ST STAGE BUCKETS GENERAL CONDITION –
MS6001B (SHEET 1 OF 4)
CODING KEYS
Buckets S/N & Positions:
Erosion/Corrosion: Code = E/C
Serial number from bottom of blade (if available) and position on State dimensions of corrosion. Use coding key to indicate the wheel.
effected zone.
Cracks: Code = C
State if crack is: AX = Axial
Foreign Object Damage:
Use coding to indicate position of damage.
RD = Radial
Use letters to identify the location of cracks and their length.
CR = Cracked
Tip Rubs: P = Punctured
Indicate tip rub severity as:
T = Torn
N = Normal
M = Missing Metal
M = Moderate
L = Light
H = Heavy
Buckets
(Mark With X)
BT = Bent
NEW PRODUCT
REFURBISHED
RETURN TO SERVICE
Classification: RTS = Return to Service, R ‐ Renew, RR = Repair
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
1ST STAGE BUCKETS CORRELATION SHEET –
MS6001 (SHEET 2 OF 4)
Wheel
Position
S/N OUT
S/N IN
CRACKS
Code
Length
Erosion/Corrosion
F.O.D.
Classification
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
1ST STAGE BUCKETS CORRELATION SHEET –
MS6001 (SHEET 3 OF 4)
Wheel
Position
S/N OUT
S/N IN
CRACKS
Code
Length
Erosion/Corrosion
F.O.D.
Classification
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
1ST STAGE BUCKETS CORRELATION SHEET –
MS6001 (SHEET 4)
Wheel
Position
S/N OUT
S/N IN
CRACKS
Code
Length
Erosion/Corrosion
F.O.D.
Classification
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
2ND STAGE BUCKETS GENERAL CONDITION – MS6001B
(SHEET 1 OF 4)
CODING KEYS
Buckets S/N & Position:
Erosion/Corrosion: Code = E/C
Serial number from bottom of blade (if available) and position on turbine wheel.
State dimensions of corrosion. Use coding key to indicate the effected zone.
Cracks: Code = C
State if crack is: AX = Axial
Foreign Object Damage:
Use coding to indicate position of damage.
RD = Radial
Use letters to identify the location of cracks and their length. CR = Cracked
Tip Rubs: P = Punctured
Indicate tip rub severity as:
T = Torn
N = Normal
M = Missing Metal
M = Moderate
L = Light
H = Heavy
Buckets
(Mark With X)
BT = Bent
NEW PRODUCT
REFURBISHED
RETURN TO SERVICE
Classification: RTS = Return to Service, R ‐ Renew, RR = Repair
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
2ND STAGE BUCKETS GENERAL CONDITION – MS6001B
(SHEET 2 OF 4)
Wheel
Position
S/N OUT
S/N IN
Cracks
Code
Length
Erosion/Corrosion
F.O.D.
Classification
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
2ND STAGE BUCKETS GENERAL CONDITION – MS6001B
(SHEET 3 OF 4)
Wheel
Position
S/N OUT
S/N IN
Cracks
Code
Length
Erosion/Corrosion
F.O.D.
Classification
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
2ND STAGE BUCKETS GENERAL CONDITION – MS6001B
(SHEET 4)
Wheel
Position
S/N OUT
S/N IN
Cracks
Code
Length
Erosion/Corrosion
F.O.D.
Classification
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
3RD STAGE BUCKETS GENERAL CONDITION – MS6001B & 9001E
(SHEET 1 OF 4)
CODING KEYS
Buckets S/N & Position:
Erosion/Corrosion: Code = E/C
Serial number from bottom of blade (if available) and position on turbine wheel.
State dimensions of corrosion. Use coding key to indicate the effected zone.
Cracks: Code = C
State if crack is: AX = Axial
Foreign Object Damage:
Use coding to indicate position of damage.
RD = Radial
Use letters to identify the location of cracks and their length. CR = Cracked
Tip Rubs: P = Punctured
Indicate tip rub severity as:
T = Torn
N = Normal
M = Missing Metal
M = Moderate
L = Light
H = Heavy
Buckets
(Mark With X)
BT = Bent
NEW PRODUCT
REFURBISHED
RETURN TO SERVICE
Classification: RTS = Return to Service, R ‐ Renew, RR = Repair
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
3RD STAGE BUCKETS GGENERAL CONDITION – MS6001B & 9001E
(SHEET 2 OF 4)
Wheel
Position
S/N OUT
S/N IN
Cracks
Code
Length
Erosion/Corrosion
F.O.D.
Classification
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
3RD STAGE BUCKETS GENERAL CONDITION – MS6001B & 9001E
(SHEET 3 OF 4)
Wheel
Position
S/N OUT
S/N IN
Cracks
Code
Length
Erosion/Corrosion
F.O.D.
Classification
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
3RD STAGE BUCKETS GENERAL CONDITION – MS6001B & 9001E
(SHEET 4)
Wheel
Position
S/N OUT
S/N IN
CRACKS
Code
Length
Erosion/Corrosion
F.O.D.
Classification
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
1ST STAGE SHROUDS GENERAL CONDITION – MS6001B
SHROUD NO.:
SHROUD SURFACE DEFECTS
DAMAGE
NONE
Position
LIGHT
Position
MEDIUM
Position
HEAVY
Position
Corrosion
Erosion
Cracks
Foreign Object Damage
Rubs/Wear
Deposits
Percentage of Nozzle cooling Holes Plugged
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
COMBUSTION CANS GENERAL – MS5001, 6001B, & 7001E
CAN NO.:
S. NO OUT
S. NO IN
CONDITION
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
CROSS FIRE TUBE GENERAL CONDITION – MS6001B
TO POSITION NO.: CROSS FIRE TUBE POSITION NO.: CONDITION
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
CROSS FIRE TUBE RETAINER GENERAL CONDITION – MS6001B
TO POSITION NO.: CROSS FIRE TUBE POSITION RETAINER NO.: CONDITION
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
CROSS FIRE TUBE GENERAL CONDITION – MS6001 DLN
CROSS FIRE TUBE POSITION NO.: TO POSITION NO.: CONDITION
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
CROSS FIRE TUBE RETAINER GENERAL CONDITION –
MS6001 DLN
TO POSITION NO.: CROSS FIRE TUBE POSITION RETAINER NO.: CONDITION
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
1ST STAGE TURBINE CLEARANCES – MS6001B
1ST STAGE TURBINE CLEARANCES
OPENING
Left
CLOSING
Right
Left
Right
SPECIFICATION
1N1
1N2
1F1
1F2
1F3
1F4
1F5
1F6
1A1
1A2
1A3
1A4
1R
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
2ND STAGE TURBINE CLEARANCES – MS6001B
2ND STAGE TURBINE CLEARANCES
OPENING
Left
CLOSING
Right
Left
Right
SPECIFICATION
2F1
2F2
2F3
2F4
2A1
2A2
2A3
2B
2S
2SA
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
3RD STAGE TURBINE CLEARANCES – MS6001B
3RD STAGE TURBINE CLEARANCES
OPENING
Left
CLOSING
Right
Left
Right
SPECIFICATION
3F1
3F2
3F3
3F4
3A1
3A2
3A3
3A4
3A5
3B
3S
3SA
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
NOZZLE TURBINE CLEARANCES – MS6001B
3RD STAGE TURBINE CLEARANCES
OPENING
Left
CLOSING
Right
Left
Right
SPECIFICATION
A
AC
1PH
1PL
B
BC
2PH
2PL
E
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
ACCESSORY & LOAD COUPLING – MS3002, 5001, 5002, 6001B,
7001E, & 9001E
Note:
1: Alignment checks to be taken looking in the downstream position.
2: Rim readings should reflect indicator riding at coupling outside diameter or on male rabbet;
if indicator rides on female rabbet, the sign conventions must be converted.
3: Couplings should all be shunted to the downstream position for all checks.
ACCESSORY COUPLING
ALIGNMENT DATA OPENING
POSITION
TOP
LEFT
BOTTOM
RIGHT
BOTTOM
RIGHT
BOTTOM
RIGHT
BOTTOM
RIGHT
Rim
Face
ALIGNMENT DATA CLOSING
POSITION
TOP
LEFT
Rim
Face
LOAD COUPLING
ALIGNMENT DATA OPENING
POSITION
TOP
LEFT
Rim
Face
ALIGNMENT DATA CLOSING:
POSITION
TOP
LEFT
Rim
Face
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
ALIGNMENT SUPPORTS – MS5001 & 6001B
DIAL INDICATOR LOCATIONS
SUPPORT JACK LOCATIONS
DIAL INDICATOR READINGS
A
B
C
D
E
A. Jack Inlet Bell / Fwd Flange
(0.006” +/‐ 0.001”)
Inspector:
Date:
Inspector:
Date:
Inspector:
Date:
Inspector:
Date:
Inspector:
Date:
B. Jack Fwd Comp. / Aft Comp. Flange*
(0.002” ‐ 0.003”)
C. Jack Aft Comp. / Discharge Flange
(0.002” ‐ 0.003”)
D. Jack Discharge / Turbine Flange
(0.002” ‐ 0.003”)
E. Jack turbine / Exhaust Flange
(0.004” ‐ 0.001”)
*Note: Not required if compressor case is a one‐piece case (no aft case)
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
BEARING & SEAL CLEARANCES, NO. 1 – MS6001B
(SHEET 1 OF 3)
Bearing Angularity:
(1B1 ‐ 1B2) = L
or
Rotor should be shunted into the upstream position (towards the accessory compartment)
(1B2 ‐ 1B1) =
L
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
BEARING & SEAL CLEARANCES, NO. 1 – MS6001B
(SHEET 2 OF 3)
INSPECTION DATA
OPENING
CLEARANCES
DIM
Left
Top
Right
Bottom
COMMENTS
1S1
1S2
1S3
1S4
1S5
1S6
1S7
1S8
1S9
1S10
1WF1
OPENING
DIM
DESCRIPTION
TAS
INSP. DATE
Rotor Float
T1
T1S
MEASUREMENT
Inactive Thrust
Upper Half
Shim Thickness
Lower Half
Active Thrust
Upper Half
Shim Thickness
Lower Half
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
BEARING & SEAL CLEARANCES, NO. 1 – MS6001B
(SHEET 3)
CLOSING
CLEARANCES
DIM
Left
Right
Left
COMMENTS
Right
1S1
1S2
1S3
1S4
1S5
1S6
1S7
1S8
1S9
1S10
1WF1
CLOSING
DIM
DESCRIPTION
T1
Rotor Float
T1S
TAS
MEASUREMENT
Inactive Thrust
Upper Half
Shim Thickness
Lower Half
Active Thrust
Upper Half
Shim Thickness
Lower Half
INSP. DATE
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
BEARING & SEAL CLEARANCES, NO. 2 – MS6001B
(SHEET 1 OF 2)
Bearing Angularity:
(2B1 ‐ 2B2) = L
or
Clamp sizes only to be taken #2 bearing is moved.
(2B2 ‐ 2B1) =
L
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
BEARING & SEAL CLEARANCES, NO. 2 – MS6001B
(SHEET 2)
INSPECTION DATA
OPENING
DIM
CLEARANCES
Left
Right
Left
Right
COMMENTS
2S1
2S2
2S3
2B1
2B2
BC1
BC2
CLOSING
DIM
CLEARANCES
Left
Right
Left
Right
COMMENTS
2S1
2S2
2S3
2B1
2B2
BC1
BC2
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
JOURNAL BEARING (GENERAL CONDITION) – MS3002, 5001/2,
6001B, 7001E/F, & 9001E/F (SHEET 1 OF 2)
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
JOURNAL BEARING (GENERAL CONDITION) – MS3002, 5001/2,
6001B, 7001E/F, & 9001E/F (SHEET 2)
Brg No.
1
Code
2
Zone
Code
3
Zone
Code
4
Zone
Code
Zone
Burn Pat.
Cracks
Babb. Loss
Babb. Smr
Dispos.
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
SLEEVE JOURNAL BEARING NO. 1 – MS5001, 6001B
(SHEET 1 OF 2)
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
SLEEVE JOURNAL BEARING NO. 1 – MS5001, 6001B
(SHEET 2)
BRG NO.
1
CODE
2
ZONE
CODE
ZONE
Burn Pat.
Cracks
Babb. Loss
Babb. Smr
Dispos.
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
OIL DEFLECTOR (ALIGNMENT) – MS3002, 5001,
5002, 6001B, 7001E/F, & 9001E/F
OIL
DEFLECTOR
POSITION (MILS)
1
2
3
4
5
CLEARANCE
6
Median
Min
Max
IDEAL POSITION
Top
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
Bottom Sides
AS LEFT
Apr 27/11
Data Sheets
ROTOR JOURNAL CONDITION – MS3002,
5001/2, 6001B, 7001E/F, & 9001E/F
OPENING
0 DEGREES
90 DEGREES
ALL
0 DEGREES
90 DEGREES
ALL
Maximum
Minimum
Difference
Average
CLOSING
Maximum
Minimum
Difference
Average
RESULTS
0 DEGREES
90 DEGREES
1
2
3
4
5
6
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
TILTING PAD THRUST BEARINGS KINGSBURY – MS6001B
TYPE CODES
SHIM THICKNESS
I.
HP Active
II.
HP Inactive
III.
LP Active*
IV.a
LP Inactive*
IV.b
VISUAL
INSPECTION
TYPE
PAD SURFACE
PAD SUPPORTS
LEVELING
COLLAR
Condition Disposition Condition Disposition Condition Disposition Condition
Disposition
HP Active
HP Inactive
LP Active*
LP Inactive*
N
W
CR
BT
M
J
BR
AJ
S
F
D
Condition Codes
Normal
Worn
Cracked
Bent
Missing Metal
Jammed
Broken
Adjustments
Scored
Fretted
Deformed
N
RG
RC
RO
RN
RR
Disposition Codes
No Repair or Replacement Necessary
Repaired By WGHIT
Repaired By Customer
Repaired By Other
Replaced With New Component
Replacement Recommended
Thrust Clearance
HP
LP*
Opening
Closing
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
ROTOR CLEARANCES - MS6001B
NOTE: Clearances to be taken with the rotor upstream against the loaded thrust face. All sizes to be taken using feeler gauges.
ROTOR STAGE
R1
S1
R2
S2
R3
S3
R4
S4
R5
S5
R6
S6
R7
S7
R8
S8
R9
S9
R10
S10
OPENING
Left
Right
CLEARANCEOMETER
CHECK
1 Stage
8th Stage
16th Stage
CLOSING
Left
Right
OPENING
Left
Right
Rotor Stage
CLOSING
Left
Right
R11
S11
R12
S12
R13
S13
R14
S14
R15
S15
R16
S16
R17
S17
EXGV1
EXGV2
TOP
BOTTOM
LEFT
RIGHT
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
V.I.G.V. GENERAL CONDITION – MS5002, 6001B, & F
(SHEET 1 OF 3)
Classification: RTS = Return To Service, R = Renew, RR = Repair
VIGV CRACK DAMAGE
QUANTITY
CLASSIFICATION
Tip Cracks
Root Cracks
Midspan Cracks
Brazed Joint Cracks
CONDITION CHECKS
(MARK WITH X)
CORROSION
EROSION
Light
Medium
Heavy
Severe
NONE
DRY
DEPOSITS (MARK WITH X)
SOOTY
OILY
AUXILIARY COMPONENTS
COMPONENT
Rack
Gears
Gear Bushings
Root Bushing
Tip Bushing
Thrust Washer
Outer Shaft
Inner Stub
WEAR
CORROSION
CRACKS
MISSING MATERIAL
CLASSIFICATION
COMMENTS
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
VARIABLE INLET GUIDE VANES GENERAL CONDITION –
MS5002, 6001B, & F (SHEET 2 OF 3)
POSITION
SPEC. SIZE
X
Inner
Outer
X Actual
Note: X is measured with rotor loaded Fwd. Inner and Outer dimensions are with VIGVs full open.
Vane Inner Gap
Outer Gap
Backlash
Bush Clear Vane Inner Gap
Outer Gap
Backlash
V‐1
V‐11
V‐2
V‐12
V‐3
V‐13
V‐4
V‐14
V‐5
V‐15
V‐6
V‐16
V‐7
V‐17
V‐8
V‐18
V‐9
V‐19
V‐10
V‐20
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
Bush Clear
AS LEFT
Apr 27/11
Data Sheets
VARIABLE INLET GUIDE VANES GENERAL CONDITION –
MS5002, 6001B, & F (SHEET 3)
Vane Inner Gap
Outer Gap
Backlash
Bush Clear Vane Inner Gap
V‐21
V‐43
V‐22
V‐44
V‐23
V‐45
V‐24
V‐46
V‐25
V‐47
V‐26
V‐48
V‐27
V‐49
V‐28
V‐50
V‐29
V‐51
V‐30
V‐52
V‐31
V‐53
V‐32
V‐54
V‐33
V‐55
V‐34
V‐56
V‐35
V‐57
V‐36
V‐58
V‐37
V‐59
V‐38
V‐60
V‐39
V‐61
V‐40
V‐62
V‐41
V‐63
V‐42
V‐64
Outer Gap
Backlash
Bush Clear
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
2ND STAGE SHROUDS GENERAL CONDITION – MS6001B
CLASSIFICATION
Return to Service
Repair
Replace
SHROUD SURFACE DEFECTS
DAMAGE
NONE
Position
LIGHT
Position
MEDIUM
Position
HEAVY
Position
Corrosion
Erosion
Cracks
Foreign Object Damage
Rubs/Wear
Deposits
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
2ND STAGE DIAPHRAGM SEALS – MS6001B & 9001E
(SHEET 1 OF 2)
DEFECT CODES
Worn Rubbed
Corroded
Bent
Eroded
Missing Pieces
DIAPHRAGM
SEGMENT
WR
CO
BT
ER
MP
DIAPHRAGM SEAL
RADIAL TEETH
DISPOSITION CODES
No repair or replacement necessary
Replaced with new component
Replacement Recommended
Repaired by customer
Repaired by other
N
RN
RR
RC
RO
WHEELSPACE SEAL
1st Stage Aft
2nd Stage Fwd
COMMENTS
Condition Disposition Condition Disposition Condition Disposition
1
2
3
4
5
6
7
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
2ND STAGE DIAPHRAGM SEALS – MS6001B & 9001E
(SHEET 2)
DIAPHRAGM
SEGMENT
DIAPHRAGM SEAL
RADIAL TEETH
WHEELSPACE SEAL
1st Stage Aft
2nd Stage Fwd
COMMENTS
Condition Disposition Condition Disposition Condition Disposition
8
9
10
11
12
13
14
15
16
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
3RD STAGE DIAPHRAGM SEALS – MS6001B (SHEET 1 OF 2)
DEFECT CODES
Worn Rubbed
Corroded
Bent
Eroded
Missing Pieces
DIAPHRAGM
SEGMENT
WR
CO
BT
ER
MP
DIAPHRAGM SEAL
RADIAL TEETH
DISPOSITION CODES
No repair or replacement necessary
Replaced with new component
Replacement Recommended
Repaired by customer
Repaired by other
N
RN
RR
RC
RO
WHEELSPACE SEAL
1st Stage Aft
2nd Stage Fwd
COMMENTS
Condition Disposition Condition Disposition Condition Disposition
1
2
3
4
5
6
7
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
3RD STAGE DIAPHRAGM SEALS – MS6001B (SHEET 2)
DIAPHRAGM
SEGMENT
DIAPHRAGM SEAL
RADIAL TEETH
WHEELSPACE SEAL
1st Stage Aft
2nd Stage Fwd
COMMENTS
Condition Disposition Condition Disposition Condition Disposition
8
9
10
11
12
13
14
15
16
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
NOZZLE, ELLIPTICITY, & RADIAL CONCENTRICITY
CHECKS 1ST STAGE – MS6001B
NOTE: Take dia. readings at the I.D. of the outer sidewall and at the centre of the nozzle segment.
Vertical dimension V =
Horizontal dimensions =
(Average H1 & H2)
Ellipticity (H‐V) =
NOZZLE TO SUPPORT RING DIMENSION
CONDITION
Pos No. 1
Pos No. 2
Pos No. 3
Pos No. 4
Pos No. 5
MAX.
ECC.
Pos No. 6
DISASSEMBLY
REASSEMBLY
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
NOZZLE, ELLIPTICITY 1ST STAGE – MS3002, 5001/2,
6001B, 7001E/F, & 9001E/F (SHEET 1 OF 2)
NOTE: Take dimensions across the half joint of the nozzle assembly.
ELLIPTICITY
Vertical
Horizontal H2
Horizontal H1
(H1+H2)/2
Ellipticity
Nozzle Out S/N
Nozzle Out Fired Hours
Nozzle In S/N
Nozzle Ins Fired Hours
SURFACE DEFECTS
None
Light
Medium
Other Observations
Heavy
Deposits
Corrosion
Erosion
Foreign Object Damage
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
NOZZLE, ELLIPTICITY 1ST STAGE – MS3002, 5001/2,
6001B, 7001E/F, & 9001E/F (SHEET 2)
RETURN TO SERVICE
REPAIR
REPLACE
Nozzle Condition
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
2ND STAGE NOZZLE CONDITION – MS5001, 6001 B/F
NOTE: Take diameter dimensions across the half joint of the nozzle assembly.
ELLIPTICITY
Vertical
Horizontal H2
Horizontal H1
(H1+H2)/2
Ellipticity
Nozzle Out S/N
Nozzle Out Fired Hours
Nozzle In S/N
Nozzle Ins Fired Hours
SURFACE DEFECTS
None
Light
Medium
Other Observations
Heavy
Deposits
Corrosion
Erosion
Foreign Object Damage
RETURN TO SERVICE
REPAIR
REPLACE
Nozzle Condition
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
NOZZLE GENERAL CONDITION, 3RD STAGE – MS6001 B/F
Nozzle Out S/N
Nozzle Out Fired Hours
Nozzle In S/N
Nozzle Ins Fired Hours
SURFACE DEFECTS
None
Light
Medium
Other Observations
Heavy
Deposits
Corrosion
Erosion
Foreign Object Damage
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
1ST STAGE NOZZLE PARTITIONS – MS6001, 7001E, & 9001E
(SHEET 1 OF 8)
CODING KEYS
Disposition Codes:
Condition Codes:
N =
No Repair Or Replacement Needed
N =
R=
Repaired
BT = Bent/Bowed
Normal
RN = Replaced With New Component
BR = Broken
RR = Replacement Recommended
ER = Eroded
IW = Inner Wall
CR = Cracked
M =
Missing Metal
CO = Corroded
OW = Outer Wall
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
1ST STAGE NOZZLE PARTITIONS – MS6001, 7001E, & 9001E
(SHEET 2 OF 8)
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
1ST STAGE NOZZLE PARTITIONS – MS6001, 7001E, & 9001E
(SHEET 3 OF 8)
SERIAL NO.
PART NO.
Removed
Removed
Installed
Installed
NOZZLE CONDITION
Partition No.
Partition Code
Condition Code
No. of Plugged Cooling Holes
1
2
3
PARTITIONS
4
5
6
7
8
PARTITION T/EDGE BOWING
None
Light
Medium
Heavy
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
1ST STAGE NOZZLE PARTITIONS – MS6001, 7001E, & 9001E
(SHEET 4 OF 8)
SERIAL NO.
PART NO.
Removed
Removed
Installed
Installed
NOZZLE CONDITION
Partition No.
Partition Code
Condition Code
No. of Plugged Cooling Holes
9
10
11
PARTITIONS
12
13
14
15
16
PARTITION T/EDGE BOWING
None
Light
Medium
Heavy
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
1ST STAGE NOZZLE PARTITIONS – MS6001, 7001E, & 9001E
(SHEET 5 OF 8)
SERIAL NO.
PART NO.
Removed
Removed
Installed
Installed
NOZZLE CONDITION
Partition No.
Partition Code
Condition Code
No. of Plugged Cooling Holes
17
18
19
PARTITIONS
20
21
22
23
24
PARTITION T/EDGE BOWING
None
Light
Medium
Heavy
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
1ST STAGE NOZZLE PARTITIONS – MS6001, 7001E, & 9001E
(SHEET 6 OF 8)
SERIAL NO.
PART NO.
Removed
Removed
Installed
Installed
NOZZLE CONDITION
Partition No.
Partition Code
Condition Code
No. of Plugged Cooling Holes
25
26
27
PARTITIONS
28
29
30
31
32
PARTITION T/EDGE BOWING
None
Light
Medium
Heavy
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
1ST STAGE NOZZLE PARTITIONS – MS6001, 7001E, & 9001E
(SHEET 7 OF 8)
SERIAL NO.
PART NO.
Removed
Removed
Installed
Installed
NOZZLE CONDITION
Partition No.
PARTITIONS
33
34
35
Partition Code
Condition Code
No. of Plugged Cooling Holes
PARTITION T/EDGE BOWING
None
Light
Medium
Heavy
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
1ST STAGE NOZZLE PARTITIONS – MS6001, 7001E, & 9001E
(SHEET 8)
SERIAL NO.
PART NO.
Removed
Removed
Installed
Installed
NOZZLE CONDITION
Partition No.
Partition Code
Condition Code
No. of Plugged Cooling Holes
41
42
43
PARTITIONS
44
45
46
47
48
PARTITION T/EDGE BOWING
None
Light
Medium
Heavy
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
2ND STAGE NOZZLE PARTITIONS – MS6001 & 9001E
(SHEET 1 OF 10)
CODING KEYS
Disposition Codes:
Condition Codes:
N =
No Repair Or Replacement Needed
N =
R=
Repaired
BT = Bent/Bowed
Normal
RN = Replaced With New Component
BR = Broken
RR = Replacement Recommended
ER = Eroded
IW = Inner Wall
CR = Cracked
M =
Missing Metal
CO = Corroded
OW = Outer Wall
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
2ND STAGE NOZZLE PARTITIONS – MS6001 & 9001E
(SHEET 2 OF 10)
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
2ND STAGE NOZZLE PARTITIONS – MS6001 & 9001E
(SHEET 3 OF 10)
SERIAL NO.
PART NO.
Removed
Removed
Installed
Installed
NOZZLE CONDITION
Partition No.
PARTITIONS
1
2
3
4
5
6
10
11
12
Partition Code
Condition Code
No. of Plugged Cooling Holes
NOZZLE CONDITION
Partition No.
PARTITIONS
7
8
9
Partition Code
Condition Code
No. of Plugged Cooling Holes
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
2ND STAGE NOZZLE PARTITIONS – MS6001 & 9001E
(SHEET 4 OF 10)
PARTITION T/EDGE BOWING
Partition No.
1
2
3
4
5
6
7
8
9
10
11
12
None
Light
Medium
Heavy
PARTITION T/EDGE BOWING
Partition No.
None
Light
Medium
Heavy
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
2ND STAGE NOZZLE PARTITIONS – MS6001 & 9001E
(SHEET 5 OF 10)
SERIAL NO.
PART NO.
Removed
Removed
Installed
Installed
NOZZLE CONDITION
Partition No.
PARTITIONS
13
14
15
16
17
18
23
24
Partition Code
Condition Code
No. of Plugged Cooling Holes
NOZZLE CONDITION
Partition No.
PARTITIONS
19
20
21
22
Partition Code
Condition Code
No. of Plugged Cooling Holes
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
2ND STAGE NOZZLE PARTITIONS – MS6001 & 9001E
(SHEET 6 OF 10)
PARTITION T/EDGE BOWING
Partition No.
13
14
15
16
17
18
19
20
21
22
23
24
None
Light
Medium
Heavy
PARTITION T/EDGE BOWING
Partition No.
None
Light
Medium
Heavy
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
2ND STAGE NOZZLE PARTITIONS – MS6001 & 9001E
(SHEET 7 OF 10)
SERIAL NO.
PART NO.
Removed
Removed
Installed
Installed
NOZZLE CONDITION
Partition No.
PARTITIONS
25
26
27
28
29
30
35
36
Partition Code
Condition Code
No. of Plugged Cooling Holes
NOZZLE CONDITION
Partition No.
PARTITIONS
31
32
33
34
Partition Code
Condition Code
No. of Plugged Cooling Holes
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
2ND STAGE NOZZLE PARTITIONS – MS6001 & 9001E
(SHEET 8 OF 10)
PARTITION T/EDGE BOWING
Partition No.
25
26
27
28
29
30
31
32
33
34
35
36
None
Light
Medium
Heavy
PARTITION T/EDGE BOWING
Partition No.
None
Light
Medium
Heavy
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
2ND STAGE NOZZLE PARTITIONS – MS6001 & 9001E
(SHEET 9 OF 10)
SERIAL NO.
PART NO.
Removed
Removed
Installed
Installed
NOZZLE CONDITION
Partition No.
PARTITIONS
37
38
39
40
41
42
47
48
Partition Code
Condition Code
No. of Plugged Cooling Holes
NOZZLE CONDITION
Partition No.
PARTITIONS
43
44
45
46
Partition Code
Condition Code
No. of Plugged Cooling Holes
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
2ND STAGE NOZZLE PARTITIONS – MS6001 & 9001E
(SHEET 10)
PARTITION T/EDGE BOWING
Partition No.
37
38
39
40
41
42
43
44
45
46
47
48
None
Light
Medium
Heavy
PARTITION T/EDGE BOWING
Partition No.
None
Light
Medium
Heavy
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
3RD STAGE NOZZLE PARTITIONS – MS6001B & 9001E
(SHEET 1 OF 10)
CODING KEYS
Disposition Codes:
Condition Codes:
N =
No Repair Or Replacement Needed
N =
Normal
R=
Repaired
BT =
Bent/Bowed
RN =
Replaced With New Component
BR =
Broken
RR =
Replacement Recommended
ER =
Eroded
IW =
Inner Wall
CR =
Cracked
M =
Missing Metal
CO
Corroded
OW
Outer Wall
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
3RD STAGE NOZZLE PARTITIONS – MS6001 & 9001E
(SHEET 2 OF 10)
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
3RD STAGE NOZZLE PARTITIONS – MS6001B & 9001E
(SHEET 3 OF 10)
SERIAL NO.
PART NO.
Removed
Removed
Installed
Installed
NOZZLE CONDITION
Partition No.
PARTITIONS
1
2
3
4
5
6
7
8
14
15
16
Partition Code
Condition Code
No. of Plugged Cooling Holes
NOZZLE CONDITION
Partition No.
PARTITIONS
9
10
11
12
13
Partition Code
Condition Code
No. of Plugged Cooling Holes
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
3RD STAGE NOZZLE PARTITIONS – MS6001 (SHEET 4 OF 10)
PARTITION T/EDGE BOWING
Partition No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
None
Light
Medium
Heavy
PARTITION T/EDGE BOWING
Partition No.
None
Light
Medium
Heavy
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
3RD STAGE NOZZLE PARTITIONS – MS6001 (SHEET 5 OF 10)
SERIAL NO.
PART NO.
Removed
Removed
Installed
Installed
NOZZLE CONDITION
Partition No.
PARTITIONS
17
18
19
20
21
22
23
23
30
31
32
Partition Code
Condition Code
No. of Plugged Cooling Holes
NOZZLE CONDITION
Partition No.
PARTITIONS
25
26
27
28
29
Partition Code
Condition Code
No. of Plugged Cooling Holes
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
3RD STAGE NOZZLE PARTITIONS – MS6001 (SHEET 6 OF 10)
PARTITION T/EDGE BOWING
Partition No.
17
18
19
20
21
22
23
23
25
26
27
28
29
30
31
32
None
Light
Medium
Heavy
PARTITION T/EDGE BOWING
Partition No.
None
Light
Medium
Heavy
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
3RD STAGE NOZZLE PARTITIONS – MS6001 (SHEET 7 OF 10)
SERIAL NO.
PART NO.
Removed
Removed
Installed
Installed
NOZZLE CONDITION
Partition No.
PARTITIONS
33
34
35
36
37
38
39
40
46
47
48
Partition Code
Condition Code
No. of Plugged Cooling Holes
NOZZLE CONDITION
Partition No.
PARTITIONS
41
42
43
44
45
Partition Code
Condition Code
No. of Plugged Cooling Holes
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
3RD STAGE NOZZLE PARTITIONS – MS6001 (SHEET 8 OF 10)
PARTITION T/EDGE BOWING
Partition No.
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
None
Light
Medium
Heavy
PARTITION T/EDGE BOWING
Partition No.
None
Light
Medium
Heavy
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
3RD STAGE NOZZLE PARTITIONS – MS6001 (SHEET 9 OF 10)
SERIAL NO.
PART NO.
Removed
Removed
Installed
Installed
NOZZLE CONDITION
Partition No.
PARTITIONS
49
50
51
52
53
54
55
56
62
63
64
Partition Code
Condition Code
No. of Plugged Cooling Holes
NOZZLE CONDITION
Partition No.
PARTITIONS
57
58
59
60
61
Partition Code
Condition Code
No. of Plugged Cooling Holes
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
3RD STAGE NOZZLE PARTITIONS – MS6001 (SHEET 10)
PARTITION T/EDGE BOWING
Partition No.
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
None
Light
Medium
Heavy
PARTITION T/EDGE BOWING
Partition No.
None
Light
Medium
Heavy
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11
Data Sheets
SUPPORT RING GENERAL CONDITION – MS6001B
INNER SEAL
OUTER SEAL
Seal Damage & Area
SUPPORT RING GENERAL CONDITION
Damage & Zones
REMARKS:
UNIT NAME UNIT SERIAL NO. MODEL UNIT LOCATION (INDOORS/OUTDOORS) INSTRUMENTATION ID NO. STATUS:
CALIBRATION DUE DATE WEATHER CONDITIONS TIME DATE READING TAKEN BY APPROVED BY TP-GE-F6
AS FOUND
AS LEFT
Apr 27/11