Installation for Mazda Miata (ND) PN-11919

BORLA PERFORMANCE INDUSTRIES
500 Borla Drive
Johnson City TN, 37604-7523
805-986-8600
Installation for Mazda Miata (ND)
PN-11919
***** Please compare the parts in the box with the bill of materials provided *****
to assure that you have all the parts necessary for this installation.
These instructions have been written to help you with the installation of your Borla Performance Exhaust System. Please read this document completely before beginning the installation of your system.
To ensure this part number fits your specific model year, please visit our website for the latest model year listings at www.BORLA.com
Thank you for purchasing a Borla Performance Exhaust System.
Borla Performance Rear Section Exhaust System (PN-11919) is designed for the Mazda Miata (ND)
equipped with a 2.0L engine, automatic or manual transmissions.
Borla Performance Industries recommends that an exhaust shop or professional after market parts installer perform the installation of
this system. However, if you decide to perform the installation on your own it is recommended that two people are used. This installation should not be performed by one person due to the risk of injury. Ensure the installers use all under car safety precautions including eye protection.
Please take time to read and understand the following…
By installing your Borla Performance Exhaust System, you indicate that you have read this document and you agree with the terms
stated below.
It is the responsibility of the purchaser to follow all installation instruction guidelines and safety procedures supplied with your Borla
Performance Exhaust System.
Borla Performance Industries assumes no responsibility for damages occurring from misuse, abuse, improper installation, improper
operation, lack of responsible care, or all previously stated reasons resulting from incompatibility with other manufacturer’s products
and/or systems.
Included with your Borla Performance Exhaust System is a warranty card. Please read it carefully before you begin any work on
your vehicle. If you should have any questions regarding our warranty policy, installation, or any other matter pertaining to your new
Borla Performance Exhaust System, please give us a call at the number provided on the warranty card.
INSTALLATION INSTRUCTIONS
DOCUMENT PART NUMBER
PAGE
Mazda Miata (ND)
A-35851 Rev. B
1 of 4
BORLA PERFORMANCE INDUSTRIES
500 Borla Drive
Johnson City TN, 37604-7523
805-986-8600
Minimum Required Tool List:
TOOLS:
1
2
3
5
3/8” Drive Ratchet
3/8” Drive Extension 3”
13mm Socket
Pry Bar
SHOP SUPPLIES:
1
Spray Lubricant
Borla Performance - Bill of Materials
11919
INSTALLATION INSTRUCTIONS
DOCUMENT PART NUMBER
PAGE
Mazda Miata (ND)
A-35851 Rev. B
2 of 4
BORLA PERFORMANCE INDUSTRIES
500 Borla Drive
Johnson City TN, 37604-7523
805-986-8600
Caution!!! Never work on a hot exhaust system. Serious injury in the form of burns can result If the vehicle
has been in use and the exhaust system is hot, allow vehicle to cool for at least 1 hour. Always wear eye
protection when working under any vehicle.
Note: It is our recommendation that you use a hoist or hydraulic lift to facilitate the installation of your new
Borla Performance Exhaust System.
Taking all under car safety precautions, lift the vehicle using a hoist or hydraulic lift. Once this has been
done, you may begin the removal of your old exhaust system from your vehicle.
Note: Before removing the original exhaust system from your vehicle, please compare the parts you have
received with the bill of materials provided on the previous page to assure that you have all the parts necessary for the installation of your new Borla Performance Exhaust System.
Note: With a used vehicle, we suggest a penetrating spray lubricant to be applied liberally
to all exhaust fasteners and allowing a significant period of time for the chemical to lubricate the threads before attempting to disassemble.
Original Exhaust
System Removal
1
2
1. Loosen (2) flange nuts using a 13mm socket, put hardware to the
side. NOTE: Reuse factory gasket. (See Figs. 1 & 2)
2. Using a muffler stand or an additional person to hold the muffler assembly, slide the (4) hangars out of the rubber isolators and remove
the system from the rear. Keep the hardware for use during the installation of your new exhaust system. (See Fig. 3)
3
Reuse Factory Gasket
3. Exhaust system removed. (See Fig. 4)
WARNING: Use extreme caution during installation. Torque all fasteners according to manufacturer’s torque values and tightening sequence. DO NOT use air impact tools to tighten fasteners on
Borla Performance Exhaust Systems. Use of such tools may result in bent flanges or gasket contact
areas leading to exhaust leaks.
4
NOTE: When you first start your vehicle after the installation of your new Borla Performance
Exhaust System, there may be some smoke and fumes coming from the system. This is a protective
oil based coating used in the manufacturing of mandrel bent performance exhaust tubing. This is
not a problem and will disappear within a very short period of time after the exhaust has reached
normal operating temperatures.
INSTALLATION INSTRUCTIONS
DOCUMENT PART NUMBER
PAGE
Mazda Miata (ND)
A-35851 Rev. B
3 of 4
BORLA PERFORMANCE INDUSTRIES
500 Borla Drive
Johnson City TN, 37604-7523
805-986-8600
Borla Performance
Exhaust System Installation
5
1. Install Muffler Assembly to vehicle carefully inserting hangers into
rubber isolators. (See Fig. 5)
2. NOTE: Reuse factory gasket. Install Muffler Assembly to vehicle
flange using factory hardware and provided Copper Lock Nut. (See
Figs. 6 & 7)
3. Check your exhaust system for proper clearance under the vehicle
and also for tip alignment. Once position has been determined to be
correct, tighten the clamp bolts, 32-35 ft. lbs. Then tighten the flange
bolts, 12-15 ft. lbs. (See Fig. 8)
4. Before starting your vehicle, make sure to check all wires, hoses,
brake lines, body parts and tires for safe clearance from the exhaust
system.
5. Start vehicle and check for any leaks. If any leaks are found, determine cause (such as loose or incorrectly positioned clamp) and repair
as necessary.
WARNING: Use extreme caution during installation. Torque all fasteners according to manufacturer’s torque values and tightening sequence. DO NOT use air impact tools to tighten fasteners on
Borla Performance Exhaust Systems. Use of such tools may result in bent flanges or gasket contact
areas leading to exhaust leaks.
6
7
8
NOTE: When you first start your vehicle after the installation of your new Borla Performance
Exhaust System, there may be some smoke and fumes coming from the system. This is a protective
oil based coating used in the manufacturing of mandrel bent performance exhaust tubing. This is
not a problem and will disappear within a very short period of time after the exhaust has reached
normal operating temperatures.
INSTALLATION INSTRUCTIONS
DOCUMENT PART NUMBER
PAGE
Mazda Miata (ND)
A-35851 Rev. B
4 of 4