manual - Snorkel

Transcription

manual - Snorkel

REPAIR PARTS
MANUAL
Serial number 000000 and after
Part Number 1500835
November 2014
The aerial platform is not electrically insulated. Death or serious injury will result from contact
with, or inadequate clearance from, an energized conductor.
Do not go closer than the Minimum Safe Approach Distance as defined by ANSI standards.
Regard all conductors as energized.
Allow for electrical wire sag and aerial platform sway.
If the platform, scissors structure, or any part of the aerial platform contacts a high-voltage electrical
conductor, the entire machine can become electrically charged.
If that happens, remain on the machine and do not contact any other structure or object. This includes the ground, adjacent buildings, poles, and any other objects that are not part of the aerial
platform.
Such contact could make your body a conductor to the other object, creating an electrical shock
hazard resulting in death or serious injury.
If an aerial platform is in contact with an energized conductor the platform operator must warn ground
personnel in the vicinity to stay away. Their bodies can conduct electricity creating an electrical shock
hazard resulting in death or serious injury.
Do not approach or leave the aerial platform until the electricity has been turned off.
Do not attempt to operate the lower controls when the platform, scissors structure, or any part of
the aerial platform is in contact with a high-voltage electrical conductor or if there is an immediate
danger of such contact.
Personnel on or near an aerial platform must be continuously aware of electrical hazards, recognizing that death or serious injury can result from contact with an energized conductor.
California
Proposition 65 Warning
Battery posts, terminals and related accessories contain lead
and lead components, chemicals known to the State of California
to cause cancer and birth defects or other reproductive harm.
Wash hands after handling.
© Snorkel – all rights reserved
Table of Contents
Electrical Hazard...................... Inside front cover
California Proposition 65.......... Inside front cover
General Information
About This Manual
Repairs and Maintenance
Abbreviations
Additional Information
Component Identification
Service and Parts Information
Ordering Parts
ANSI and OSHA Compliance
Manuals
Machine Information
Parts Order Form
Repair Parts
Chassis, Steering and Brakes................... CSB
Pothole Protector...................................... PHP
Rear Tray.....................................................RT
Control Tray..................................................CT
Hydraulic Tray..............................................HT
Battery Trays................................................ BT
Scissor Stack...............................................SS
Lift Cylinder Mounting ............................LCMT
Platform...................................................... PLT
Placards and Decals....................................PD
Placards and Decals – Spanish..............PDES
Hydraulics
Pump Unit.................................................PMU
Hydraulic Brake/Hub..............................BRK/H
Manifold Valve............................................. MV
Steering Cylinder....................................... SCY
Lift Cylinder................................................LCY
S3219E/S4732E – 1500835
Electrical
Lower Control Panel...................................LCP
Upper Control Box....................................... UC
Joystick....................................................JSTK
Chassis Harness.......................................... CH
Chassis Harness Section A.......................CH-A
Chassis Harness Section B.......................CH-B
Chassis Harness Section C..................... CH-C
Chassis Harness Pin ID............................CHID
Stack Harness.............................................. SH
Options
Loading Control......................................... LDC
Maintenance
Maintenance
Daily Prestart Inspection
Frequent Inspection and Maintenance
Annual Maintenance
Major Repairs
Lubrication Points
Batteries
Fastener Torque Chart – Standard
Fastener Torque Chart – Metric
Appendix
Hydraulic Schematic.................................... HS
Limited Warranty
Contact Information
Europe, Middle East, Africa/Asia.....Back cover
North and South America................Back cover
Australia..........................................Back cover
New Zealand...................................Back cover
S3219E/S4732E – 1500835
General Information
About This Manual
This manual covers S1930E and S1932E aerial platforms. Information is included for machines that have
been manufactured to conform to all applicable requirements of the following organizations:
yy
yy
yy
yy
American National Standards Institute (ANSI)
Canadian Standards Association (CSA)
European Committee for Standardization (CE)
Australian Standards (AS) certification
Part pages include a drawing and a bill of material.
The bill of material lists the item number that is on the
drawing, the Snorkel part number, quantity used and a
description of the item.
Some callouts in the drawings may have a balloon with
two numbers. The top number is the item number and
the bottom number is the quantity of the item at that
location.
While Snorkel has attempted in every way to confirm that
all information in this manual is correct, improvements
are being constantly made to the machine that may not
be reflected in this manual.
If you find information in this manual that is not correct
or is confusing, you are urged to report your findings to
Snorkel for our evaluation. Your input is important to us
and will be used in future printings of this manual.
This machine is covered by a limited warranty that specifically identifies items warrantied by Snorkel and those
items covered by original manufacturer's warranty. A
copy of the Snorkel Limited Warranty is located on the
inside of the back cover of this manual.
Repairs and Maintenance
Every person who maintains, inspects, tests or repairs
the machine must be qualified and authorized to do so.
Caution
Do not modify this aerial platform without prior
written consent of Snorkel Engineering Department.
Modification may void the warranty, adversely affect
stability or affect the operational characteristics of
the aerial platform.
Abbreviations
The following abbreviations may be used in this manual.
AC
alternating current
ANSI American National Standards Institute
AR
as required
CCA cold cranking amps
cmcentimeter
DC
direct current
ftfeet
GFCI ground fault circuit interruptor
ininch
lbspounds
mmmillimeter
nonumber
NPT national pipe thread
psi
pounds per square inch
qtyquantity
rpm
revolutions per minute
UL
Underwriters Laboratories Inc.
Additional Information
All correspondence relative to this machine, such as field
reports, discrepancy reports, requests for information,
etc., should be directed to:
Snorkel North America
P.O. Box 1160
St. Joseph, MO 64502-1160 USA
Phone: 1-800-255-0317
Snorkel Europe
Vigo Centre
Birtley Road
Washington
Tyne & Wear
NE38 9DA
Phone: +44 (0) 845 1550 058
http://www.snorkellifts.com
S3219E/S4732E – 1500835
Component Identification
Platform Extension
Platform
Toeboards
Emergency
Lowering Lever
Entry
Step
Drive and Steer
Wheels
Control Valve Tray
Freewheeling Valve/Brake Release Valve
Hand Pump/Diagnostic Display
Serial
Number
Tie-Down/Lifting Lugs
Battery Tray
Front
Right Side
Electrical
Upper Power Outlet
Controls
Guardrails
Operator’s
Manual
Entry
Doors
Scissors
Structure
Forklift
Pockets
Tie-Down/Lifting
Lugs
Chassis
Groundstrap
Battery Tray
Hydraulic Tray
Pump/Reservior/Fluid Filter
Left Side
Pothole
Protector Skid
Battery
Charger
Receptacle
Power to Platform
Receptacle
Lower
Controls
Rear
Battery Charger
LED Charge Indicators
S3219E/S4732E – 1500835
Service and Parts Information
Ordering Parts
When placing an order for service or repair parts,
please have the following machine information readily
available.
yy
yy
yy
yy
yy
yy
yy
yy
Model number
Serial number
Snorkel part number
Description of part
Quantity of parts required
Your purchase order number
Address for order to ship to
The desired shipment method
The parts order form on the following page may be
mailed or faxed to the attention of the Parts Department
at the following location:
Snorkel North America
P.O. Box 1160
St. Joseph, MO 64502-1160 USA
Phone: 1-800-255-0317
Parts Fax: 1-785-989-3077
Snorkel Europe
Vigo Centre
Birtley Road
Washington
Tyne & Wear
NE38 9DA
Phone: +44 (0) 845 1550 058
Parts Fax: +44 (0) 1952 607 678
Manuals
Manuals are available from Snorkel to support any of
the machines that we produce.
The specific manuals for S3219E and S4732E aerial
platforms are as follows:
S3219E/S4732E Operator’s Manual ANSI
Snorkel part number – 1500834
S3219E/S4732E Operators Manual CE
S3219E/S4732E Operator’s Manual Spanish
S3219E/S4732E Repair Parts Manual
S3219E/S4732E CSA Inspection and Maintenance
Checklists
ANSI Manual of Responsibilities
ANSI/SIA A92.6-2006
Machine Information
Model Number:
Attention: Parts Department
For your convenience, our electronic on-line ordering
system is available at the following Internet location:
http://www.snorkellifts.com
Serial Number:
Date of Purchase:
ANSI and OSHA Compliance
All owners and users of the aerial platform must read,
understand and comply with all applicable regulations.
Ultimate compliance to OSHA regulations is the responsibility of the user and their employer.
Purchased From:
ANSI publications clearly identify the responsibilities
of all personnel who may be involved with the aerial
platform. A reprint of the “Manual of Responsibilities for
Dealers, Owners, Users, Operators, Lessors and Lessees of ANSI/SIA A92.6-2006 Self-Propelled Elevating
Work Platforms” is available from Snorkel dealers or
from the factory upon request.
Snorkel Dealer or Distributor:
Copies are also available from:
Scaffold Industry Association, Inc.
P.O. Box 20574
Phoenix, AZ 85036-0574 USA
S3219E/S4732E – 1500835
Parts Order Form
Fill out completely and fax attention Parts Department to:
Snorkel USA 1-785-989-3077
Snorkel Europe +44 (0) 1952 607 678
Date:
Account Number:
Company:
Purchase Order Number:
Address:
Model Number:
Serial Number:
Ship To:
Contact Name:
Phone Number:
Fax Number:
Shipping Method:
Part Number
Description
Quantity
Note: Backordered parts will be shipped as soon as available using the same shipping method as the original
order unless otherwise indicated below.

Ship complete order only. Do not backorder parts.
Ship all available parts and disposition of backordered parts.
Other instructions as specified:
S3219E/S4732E – 1500835
Repair Parts
Chassis, Steering and Brakes.................... CSB
Pothole Protector........................................ PHP
Rear Tray.......................................................RT
Control Tray...................................................CT
Hydraulic Tray...............................................HT
Battery Trays.................................................BT
Scissor Stack.................................................SS
Lift Cylinder Mounting...............................LCMT
Platform....................................................... PLT
Placards and Decals.................................... PD
Placards and Decals – Spanish...............PDES
Chassis, Steering and Brakes
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Part No.
Qty.
1500665
1500845
058492-030
5563339
1500981
058494-040
056066-012
6091501
056065-090C
056056-012
1360604
301667
056060-030
056064-010
1500745
1500729
2509814
5592015
6047139
058494-025
2509820
2580430
5592001
1500174
6031625
1500224
988229
Description
1
2
10
10
1
4
4
2
16
16
4
1
1
1
2
2
2
2
1
4
4
2
2
1
2
1
2
WLDMT, CHASSIS S3219E
PLATE CHASSIS COVER
HHCS M8 X 1.25 X 30 G8.8 ISO 4014_DIN 931
M8 X 1.25 HEX WELD NUT
WELDMENT STEP S1932E
HHCS M12 X 1.75 X 40 G8.8 DIN 933
NUT HEX M12 X 1.75 GR 8.8 SELF LOCKING DIN 985
HYD BRAKE/HUB BK10 – REFER TO HYDRAULICS BRK/H
HHCS M12 X 1.75 X 90 G8.8 DIN 931
TIRE AND WHEEL ASSEMBLY
GROUND STRAP
HHCS M10 X 1.5 X 30 G8.8 DIN 933
PLT, STEERING LINKAGE
PIN, .375DIA X .88L
BRG CSB-50-1010
RETAINING RING, EXTERNAL, 10MM DIA, BASIC
STEERING CYLINDER – REFER TO HYDRAULICS SCY
HHCS M12 X 1.75 X 25 G8.8 DIN 933
BRG CSB-50-7540
THRUST BRG, 80MMID 100MMOD 3MM THK
SNAP RING
WLDMT, STRG SPDL LH
MOTOR DRIVE
WLDMT, STRG SPDL RH
PIN COTTER .125 DIA 2.50
2
3
4
5
6
7
1
8
15
16
23
19
17
11
12
21
18
9 10
13 14
23
17
18
22
18
20
11
27
24
1500664
25
26
9 10
Chassis, Steering and Brakes
CSB
Page 1 of 1
Pothole Protectors
Item
Part No.
Qty.
1
1501293
2
3
1501056
4
056064-008
5
6
1500952
7
058492-030
8
1501055
9
10
056066-012
11
056069-016
12
1500936
13
056069-010
14
056060-045
15
056069-016
16
1501053
1501054
17
1501270
18
500532-020
Description
1
1
1
4
1
2
4
2
2
4
4
4
4
4
2
1
1
1
1
5520113
1
5520114
1
PIN, .625 DIA X 2.19 L
POTHOLE ROLLER
WLDMT POTHOLE ACTUATOR
M8-10 NUT, HEX, SELF LOCKING
PULLEY
PLT, PULLEY MNT
HHCS M8 X 1.25 X 30 G8.8 ISO 4014_DIN 931
PLT, POTHOLE PIVOT
PIN POTHOLE CENTER
M16 FLAT WASHER DIN 125
PIN, POTHOLE
HHCS M10 X 1.5 X 45 G8.8 DIN 933
POTHOLE SKID – LEFT SIDE
POTHOLE SKID – RIGHT SIDE
WSHR POTHOLE SWITCH
FSHCS M6 X 1.0 X 20 CLASS 8.8 DIN7991
NOT SHOWN
POTHOLE CABLE
TURNBUCKLE POTHOLE CABLE
1
2
3
4
5
6
7
17 18
8
9
11
10
15
12
16
13
14
PHP
1500664
Pothole Protectors
Page 1 of 1
Rear Tray
Item
Part No.
Qty.
1
1500662
2
058490-020
3
056066-005
4
3020049
5
300840
6
3069521
7
8
056066-003
9
5516346
10
5563299
11
056064-008
12
5563068
13
3087787
14
058491-020
15
056069-006
16
056066-006
17
446086
18
19
3087800
20
058492-016
21
056021-008
22
512630-030
23
3050124
24
5563283
1
4
4
1
1
2
6
6
1
3
6
3
1
2
10
12
1
2
1
3
3
4
1
4
Description
LOWER CONTROL PANEL – REFER TO ELECTRICAL LCP
HHCS M5 X 0.8 X 20 G8.8 ISO 4017_DIN 933
SW BATTERY DISCONNECT
LOCK OUT LEVER ASSEMBLY
FLANGE INLET 15A 125V NEMA 5-15
HHCS M3 X 0.5 X 20 G8.8 ISO 4014_DIN 931
HINGE DRILLED REAR TRAY
SBHCS M8 X 1.25 X 25 GR 10.9 BLK FINISH
NUT HEX M8-1.25 GR 10.9 SELF LOCKING DIN 985
CONTACTOR, 24V SEALED
HHCS M6 X 1 X 20 G8.8 ISO 4017_DIN 933
NUT, HEX M6 X 1.0 GR 8.8 SELF LOCKING DIN 985
BLOCK FUSE
M6 CAPSCREW
PG TRIONICS EZLIFT 230 CONTROLLER
HHCS M8 X 1.25 X 16 G8.8 ISO 4017_DIN 933
WSHR LOCK M8
HHCS M6 X 1 X 30 G10.9 ISO 4017_DIN 933
CHARGER, PRO CHARGER
4
12 11
6
10 11
13
14 15 16
7 8
9
6
5
23
20
21
17
7 8
16 18
19
24 15 16
1
22 16
2 3
RT
1500664
Rear Tray
Page 1 of 1
Control Tray
Item
Part No.
1
1501006
2
5516345
3
1500947
4
1500948 5
6
7
3087803
8
3049978
9
6019273
10 501868-000
Qty.
Description
1
1
1
1
1
1
1
1
1
1
VALVE TRAY
LATCH, PADDLE BLK
PIN, TRAY HINGE
PLT, TRAY PIN KEEPER
METRIC IMPERIAL BUTTON HEAD CS
METRIC NYLON LOCKNUT
LCD SCREEN
ALARM, BEEPING
MANIFOLD – REFER TO HYDRAULICS MV
HORN
2
1
3
4
5
6
10
7
8
9
CT
1501176
Control Tray
Page 1 of 1
Hydraulic Tray
Item
Part No.
Qty.
1
5516345
2
1501009
3
1500947
4 5
1500948 6
7
114067-000
114067-012
8
5076526
9
6029678
1
1
1
1
1
1
1
1
1
1
Description
LATCH, PADDLE BLK
HYDRAULIC TRAY
PIN, TRAY HINGE
METRIC IMPERIAL BUTTON HEAD CS
PLT, TRAY PIN KEEPER
METRIC NYLON LOCKNUT
RETURN FILTER TANK IMMERSED
HYDRAULIC FILTER ELEMENT
CAP WITH DIPSTICK
PUMP UNIT – REFER TO HYDRAULICS PMU
1
2
3
4
6
7
5
8
9
HT
1501009
Hydraulic Tray
Page 1 of 1
Battery Trays
Item
Part No.
1
3050009
2
1501007
3
1501008
4
1500947
5
6
1500948 7
Qty.
4
1
1
1
1
1
1
Description
BTRY 6V GOLF CAR – TWO PER TRAY
BATTERY TRAY LEFT SIDE OF CHASSIS
BATTERY TRAY RIGHT SIDE OF CHASSIS
PIN, TRAY HINGE – ONE PER TRAY
METRIC IMPERIAL BUTTON HEAD CS – ONE PER TRAY
PLT, TRAY PIN KEEPER – ONE PER TRAY
METRIC NYLON LOCKNUT – ONE PER TRAY
1
1
4
2
3
4
5
5
6
6
7
7
1501007
1501008
Left Side of Chassis
Right Side of Chassis
BT
Battery Trays
Page 1 of 1
Scissor Stack
Item
Part No.
Qty.
1
1500866
1
2
1500858
8
3
1500876
2
4
1500857
2
5
1500877
1
6
1500880
2
7
1500881
28
8
056059-085
18
9
1500882
10
10
056066-008
20
11
1500883
6
12
1500884
4
13
1500978
2
14
1500979
2
15
1500888
12
16
1500890
1
17
1500891
8
18
5592016
16
19
1500892
24
20
2509816
36
21
062642-023
32
22
1500893
2
Description
WLDMNT, FIRST INNER ARM
WLDMNT, SINGLE ARM
WLDMT, INNER ARM 3219
BOSS, STACK ROLLER 3219
WLDMT, THIRD INNER ARM 3219
PIN, LOWER SLIDER
PLT, PIN RETAINER
HHCS M8 X 1.25 X 85 G8.8 ISO 4014 DIN 931
PIN, END DOUBLE RETAINER
NUT HEX M8 X 1.25 GR 8.8 SELF LOCKING D IN 985
PIN, END
TUBE, STACK CROSS
STACK PAD, IMPERIAL, 1ST INNER
STACK PAD, IMPERIAL, 1ST OUTER
STACK PAD, IMPERIAL, UPPER
BAR, CYL ROD MNT – REFER TO REPAIR PARTS LCMT
PIN, CENTER
RETAINING RING EXT 1.25 HEAVY DUTY
WASHER, CENTER PIN
BRG CSB-50-14IB 16
BRG CSB-50-20IB 20
PLT, PLATFORM MNT BEND
CONTINUED ON NEXT PAGE...
SS
1501002
Scissor Stack
Page 1 of 2
Scissor Stack
Item
Part No.
Qty.
23
24
25
26
27
28
29
30
31
32
33
34
1500894
1500898
500532-020
056066-006
988379
1500988
1500889
056059-100
2502416
056060-030
056066-010
3030157
2
4
8
8
8
2
2
2
2
3
3
2
Description
WLDMNT, PLATFORM SLIDER
SLIDE PAD, UPPER SLIDER
FSHCS M6 X 1.0 X 20 CLASS 8.8 DIN 7991
NUT HEX M6 X1.0 GR 8.8 SELF LOCKING DIN 985
PLT, SAFETY PROP
TRUNION MNT – REFER TO REPAIR PARTS LCMT
HHCS M8 X 1.25 X 100 G8.8 ISO4014 DIN931 – REFER TO REPAIR PARTS LCMT
BRG CSB-50-24IB 16 – REFER TO REPAIR PARTS LCMT
HHCS M10 X1.5 GR 8.8 DIN 985
ANGLE TRANSDUCER
SS
Page 2 of 2
1501002
Scissor Stack
Lift Cylinder Mounting
Item
Part No.
1
2
1500890
3
2502416
4
1500889
5
056059-100
6
7
6047135
8
9
583956
10
583976
11
12
13
1500887
14
15
16
17
1500885
18
Qty.
1
1
4
4
4
4
1
1
1
1
1
1
1
1
1
1
1
2
Description
METRIC HHCS M20 X 2.5
BAR, CYL ROD MNT
BRG CSB-50-24IB 16
TRUNION MNT
HHCS M8 X 1.25 X 100 G8.8 ISO 4014 DIN 931
METRIC NYLON LOCK NUT
LIFT CYLINDER – REFER TO HYDRAULICS LCY
FTG 6MB-6MORF 90 DEG
COIL 20 VDC
VALVE CART 2WAY N/C POPPET
METRIC HHCS M8
PLT CYLINDER BLEED LEVER
METRIC HHCS M8
METRIC HEX NUT
WLDMT CYLINDER BLEED
METRIC HHCS M6
1
2
3
4
6
8
9 10
5
11 12
13
14 15 16
17
7
18
3
6
5
4
LCMT
6047135
Lift Cylinder Mounting
Page 1 of 1
Platform
Item
Part No.
Qty.
Description
1
1500964
1
2
1501106
1
3
058492-055
4
4
056067-508
4
5
056066-008
20
6
1501303
1
7
1501107
2
8
16
9
056069-010
12
GATE SALOON LH
GATE SALOON RH
HHCS M8 X 1.25 X 55 G8.8 ISO 4014_DIN 931
NUT, HEX, THIN, M8 X 1.25 DIN 936
WLDMT HNDRL OUTER MAINS S3219
PIN, .375DIA X 10.83L
RETAINING RING, EXTERNAL, .375 DIA, BASIC
CONTINUED ON NEXT PAGE...
6
8
7
9
12
1
2
8
13
11
3 4 5
5
14
15
18
16
17
19
23
18 19
43
5
19 20
21
28
34 33
29
32 8
32 8
30
31
36
32 8
38 19
22
35
24
25
37 9 19
39
40
41 42 5
28
36
27
18 19
26
1501344 C
24 25
23
PLT
Platform
Page 1 of 2
Platform
Item
Part No.
10
0071837
11
1501308
12
1501157
13
058492-020
14
1501339
15
5563446
16
17
1501175
18
056060-055
19
056064-010
20
058509-065
21
1501018
22
1501343
23
1501231
1501019
24
1501110
25
26
1501341
27
1501334
28
1501321
29
5569973
30
5563445
31
1501450
32
1501408
33
1501347
34
1501327
35
1501317
36
1501323
37
056060-080
38
056060-045
39
1501324
40
562386
41
056059-016
42
056069-008
43
058492-025
Qty.
2
1
1
4
1
4
1
1
10
22
2
1
2
5
1
4
8
2
1
2
6
2
2
6
2
2
2
2
4
2
1
1
4
4
8
Description
TORSION SPING GATE – NOT SHOWN
WLDMT HNDRL CONTROL S3219
UPPER CONTROL – REFER TO ELECTRICAL UC
HHCS M8 x 1.25 x 20 G8.8 ISO 4017 DIN 933
PLT, CABLE GUARD W/DRIVE CONT
1/4-20 PAN HEAD SCREW
LOADING CONTROL – REFER TO OPTIONS LDC
COVER, CABLE GUARD S3219
HHCS M10 X 1.5 x 55 G8.8 DIN 933
HHCS M10 X 1.5 x 65 G10.9 DIN 931
WLDMNT S3219 PLATFORM
ROLLER, MAIN DECK S3219
SLIDE PAD, PLATFORM INNER
SPACER LEFT – NOT SHOWN
PIN, .875DIA X 2.90L
RETAINING RING, EXTERNAL, .875 DIA, BASIC
ROLLER, EXT DECK INNER S3219
WLDMT EXT DECK S3219
PLT, HNDRL TOP SLIDE S3219
WEAR PAD
#8 PAN HEAD DRILLING SCREW
SPRING, EXT DECK LATCH
PIN, HNDRL SLIDER MNT
WLDMT EXT DECK SLIDER HANDLE
WLDMT EXT DECK LATCH
WLDMT HNDRL FRONT S3219
TUBE, HNDRL MID TELESCOPE S3219
HHCS M10 X 1.5 X 80 G8.8 DIN 931
HHCS M10 X 1.5 X 45 G8.8 DIN 933
WLDMT FRONT GATE S3219
COMPARTMENT LITERATURE 8.5X11
HHCS M8 X 1.25 X 16 G8.8 ISO 4017_DIN 931
HHCS M8 X 1.25 X 25 G8.8 ISO 4014_DIN 931
PLT
Page 2 of 2
1501344 C
Platform
Placards and Decals
Item
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
1501225 J
Part No.
Qty.
1501475
1501476
0073224
0073043
1501230
300699
0083426
1501472
416836
569295
1500836
7030068
0361259
1501533
1500840
451726
300760
501453-000
0181562
7030160
969249
0361533
300700
0070901
0074311
0150606
8974
451986
451776
0361367
500834
0361528
1
1
1
1
1
1
4
1
1
3
2
2
2
1
6
2
2
2
1
2
32"
1
1
1
1
1
4
1
1
1
1
1
Description
DECAL, DNGR TIPOVER/ELEC HAZARD LH
DECAL, DNGR TIPOVER/ELEC HAZARD RH
DECAL MANUAL REORDER
DECAL OPERATING INFORMATION INSIDE
DECAL PLAT CAP 550# W/WIND SP
PLACARD OPERATORS CHECKLIST
DECAL, TIE DOWN SYMBOL
DECAL, BATT CHARGER CODES
DECAL BATTEY CHARGER PLUG
DECAL, SNOKEL BRAND LOGO 3.00
DECAL S3219E MODEL
DECAL, WEB ADDRESS LOGO 1.38
DECAL, DNGR SAFETY PROP
DECAL, WARNING TOW INSTRUCTIONS
DECAL, FORKLIFT
DECAL, CHK BTRY BEFORE CHARGING
TIPOVER HAZARD DECAL
DECAL, FOOT TRAP
DECAL, MACH COMPLIES W/ANSI
SHUR-STEP 2" GP 12"
DECAL, STRIPE YE/BLK 2"
DECAL EMERGENCY BLEED DOWN
DECAL, DNGR SHEARING/CRUSHING
PLACARD SERIAL NUMBER
DECAL, DNGR CYLINDER FAILURE
DECAL, 125V 15AMP PWR TO PLATF
SCREW-HAMMER DRIVE 4MM/3/8"
DECAL. DNGR DO NOT ALTER SW
DECAL, HYDR FUID LEVEL
MANUAL RESPONSIBILITIES A92.6
MANUAL, OPERATORS S3219E ANS
DECAL CSA COMPLIANT – CSA MACHINES ONLY
Front
Right Side
Placards and Decals
PD
Page 1 of 2
Placards and Decals
Rear
Left Side
PD
Page 2 of 2
1501225 J
Placards and Decals
Placards and Decals – Spanish
Item
Part No.
0070901P
0074311P
0150606P
0181562ES
0361259P
1501230
0361533
300699P
300700P
300760P
416836P
451726P
451776P
451986P
569295
1500840
0083426
0361367
8974
1500836
501453-000
7030068
0361562ES
1501533ES
5563068
056066-008
3220141
1501480
1501474ES
1501475ES
1501476ES
7030067
Qty.
1
1
1
1
2
1
1
1
1
2
1
2
1
1
3
6
4
1
4
2
2
2
1
1
3
3
18
1
1
1
1
1
Description
PLAC CAUTN SERIAL NUMBER SPANISH
DECAL, DANGER CYLINDER FAILURE, SPANISH
DECAL 125V 15AMP PWR TO PLATF- SPANISH
DECAL MACH COMPLIES WITH ANSI- SPANISH
DECAL DNGR SAFETY PROP SPANISH
DECAL PLAT CAP 550# W/WIND SP
DECAL EMER BLEED DOWN 1930 PICTORIAL
DECAL, OPERATORS CHECKLIST, SPANISH
DECAL - BEWARE DESCENDING PLAT SPANISH
DECAL, DANGER TIP OVER HAZZARD, SPANISH
DECAL BTRY CHARGE 115V ONLY SPANISH
DECAL, CHECK BATTERY BEFORE CHARGING, SPANISH
DECAL, HYDRAULIC FLUID LEVEL, SPANISH
DECAL, DNGR DO NOT ALTER SW, SPANISH
DECAL SNORKEL BRAND LOGO 3.00
DECAL, FORKLIFT PHOENIX II
DECAL TIE DOWN SYMBOL
MANUAL RESPONSIBILITIES A92.6-2006 ANSI/SIA SCISSORS EWP
SCREW - HAMMER DRIVE 4MMX3/8"
DECAL, S3219E MODEL
DECAL, FOOT TRAP MX19 / SL20 /
DECAL, WEB ADDRESS
PLAC BATT CHARGER INFO SPANISH
DECAL, WARNING TOWING INSTRUCTIONS S3219E - SPANISH
SCR BUTT HD M8 X 20
NUT, NYLOCKNUT M8 DIN985 GR 8.8 ZINC PLATED
GRIP TAPE GT
MANUAL, OPERATORS S3219E, SPANISH
DECAL, LOADING CONTROL, SPANISH
DECAL, DNGR TIPOVER/ELEC HAZARD RH, SPANISH
DECAL, DNGR TIPOVER/ELEC HAZARD LH, SPANISH
SPANISH SHIPPING INFO
PDES
1501479
Placards and Decals – Spanish
Page 1 of 1
Hydraulics
Pump Unit.................................................PMU
Hydraulic Brake/Hub..............................BRK/H
Manifold Valve............................................. MV
Steering Cylinder....................................... SCY
Lift Cylinder................................................LCY
Pump Unit
Item
Part No.
Qty.
6029678 1
Description
PUMP UNIT 24 VDC 4.3 CC
Relief Valve
(+) Terminal
24 VDC Motor
“P” Port
4.3 CC Pump
Strainer
(-) Terminal
PMU
6029678 A
Pump Unit
Page 1 of 1
Hydraulic Brake/Hub
Item
1
2
Part No.
Qty.
6091501
6047150
5569975
Description
1
1
1
HYDRAULIC BRAKE/HUB
SEAL REPAIR KIT
1
2
BRK/H
6091501 A
Hydraulic Brake/Hub
Page 1 of 1
Manifold Valve
Item
Part No.
Qty.
6019273 1 2
6019300
3
6019301
4
6019302
5
6019303
6
6019304
7
6019305
8
6019306
9
6019307 10 6019308 11 3019309 12 3019310 13 6019311
14 6019312
15 6019313 16 6019314
17 6019315 18 6019316 19 5075305 1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
1
2
2
2
Description
MANIFOLD VALVE
MANIFOLD VALVE WITH PLUGS
SOLENOID VALVE
SOLENOID VALVE
FLOW REGULATOR
HAND PUMP
MANUAL PULL VALVE
RELIEF VALVE
SOLENOID VALVE
OVERCENTER VALVE
SHUTTLE VALVE
NEEDLE VALVE
SOLENOID COIL
ORIFICE PLUG
COIL SPACER
SOLENOID COIL
COIL SPACER
ORIFICE CHECK DISC
SOLENOID COIL
FTG PL HOL HEX
Test Port
Main System Pressure
2 14 15
3 12
5
7
1
4
10 19
8 16 18
9
6
13 19
11
17
MV
6019273 C
Manifold Valve
Page 1 of 2
Manifold Valve
SL
SR
L
B1
B2
17
RA RB
LA LB
17
2
6
4
9
3
11
P
G
7
13
10
5
8
9
T
MV
Page 2 of 2
6019273 C
Manifold Valve
Steering Cylinder
Item
Part No.
6047139
6047150
Qty.
1
1
Description
CYLINDER, STEERING
SEAL REPAIR KIT
SCY
6047139 B
Steering Cylinder
Page 1 of 1
Lift Cylinder
Item
Part No.
6047135
6047147
Qty.
1
1
Description
CYLINDER, LIFT
SEAL REPAIR KIT
LCY
6047135 C
Lift Cylinder
Page 1 of 1
Electrical
Lower Control Panel...................................LCP
Upper Control Box....................................... UC
Joystick....................................................JSTK
Chassis Harness.......................................... CH
Chassis Harness Section A.......................CH-A
Chassis Harness Section B.......................CH-B
Chassis Harness Section C..................... CH-C
Chassis Harness Pin ID............................CHID
Stack Harness.............................................. SH
Lower Control Panel
Item
1
2
3
4
5
6
Part No.
1500663
3028845
8080210
3020047
510524-000
302829
1500438 Qty.
1
1
1
1
1
1
1
Description
PLT GRD CTRL PANEL
SELECTOR SWITCH
SPARE KEYS – SET OF TWO
SW TGL SPDT (ON/NONE/ON)
PUSH/PULL SW ASSY W/NC CONTACT
LED RED
DECAL LOWER CONTROL PANEL
1
2
5
6
3
4
LCP
1500662 B
Lower Control Panel
Page 1 of 2
Lower Control Panel Wiring
Item
Part No.
1
2
3
4
5
6
7
3011641
3044155
3044161
3046697
509741-000
509740-000 3220218
Qty.
A/R
6
3
2
1
1
1
Description
WIRE 16GA SINGLE CONDUCTOR WHT
TERM SPADE 8I 16/14
TERM R10I 16/14
TERM FEM 188I 16/14 GA
BLADE FUSE HOLDER
BLADE FUSE 20 AMP
CONN AMP 9-PIN SOCKET
2
PLAT
1
P4-1
Control Select
Ground Operation
3
P4-4
P4-5
Platform Raise/Lower
P1-8
LED
4
7
5 6
EMS
FUSE HOLDER
9
8
7
6
5
4
3
2
1
LOWER
CONTROLS
1-480707-0
CAV
CKT
1
P1-8
2
P4-1
3
P4-4
4
P4-5
5
6
7
EMS
8
PLAT
9
-
Emergency Stop
LCP
Page 2 of 2
1500662 B
Lower Control Panel Wiring
Upper Control Box
Item
1
2
3
4
5
6
7
8
9
10 11 12
13
14 15
Part No.
1501112 510524-000 3020047 510542-000
302829 1501158
1501159
3040624
3040625
512714-025 056066-004 978629
1501116
1501359
3087801 Qty.
1
1
1
1
1
1
1
1
1
4
4
4
1
1
1
Description
WLDMT, UPPER CONTROL BOX
PUSH/PULL SW ASSY W/NC CONTACT
SW TGL SPDT (ON/NONE/ON)
SW PUSH BUTTON\
LIGHT RED 24 VDC BEZEL MOUNT
PLAC, PLTFRM CONT BOX
PLAC, PLTFRM CONT BOX E-STOP/HORN
RECEPTICAL GFCI OUTLET 20 AMP
WEATHERPROOF PAD
HHCS M4 X 0.7 x 25 G8.8 ISO 4014 DIN 931
BLT HEXHD SLFTPG .250-20 .500
PLT BOTTOM PLATFORM CONTROL BOX
PLAC LIFT/DRIVE
JOYSTICK – REFER TO ELECTRICAL – JSTK
1
15
5
3
6
14
8 9
12
4
10 11
13
2
7
UC
1501157 C
Upper Control Box
Page 1 of 2
Upper Control Box Wiring
Item
1
Part No.
1501298
Qty.
Description
1
CONN, S3219 CONTROL BOX
P1-7
P1-8
P8-5
P1-1
P1-3
P1-4
P3-8
P3-9
P3-12
P3-3
1
P3-6
P8-4
P3-7
P8-2
P8-3
P3-1
PLAT
P8-1
UC
Page 2 of 2
1501157 C
Upper Control Box Wiring
Joystick
Item
1
2
3
4
5
6
7
8
9
10
11
12
Part No.
3087801
3087816
3087807
3087814
3087808
3087811
3087819
3087820
3087810
3087806
3087815
3087813
5563176
Qty.
1
1
1
1
1
1
1
1
1
2
4
1
4
Description
JOYSTICK – INCLUDES ITEMS 1 THROUGH 12
RING, RETAINING, BOOT
BOOT, BH HANDLE
MOUNTING NUT
ACTUATOR, BH HANDLE
LEVER, ENABLER, BH HANDLE
GASKET, BH HANDLE
GASKET, BH HANDLE
PUSHBUTTON, MOMENTARY (BLACK)
MICROSWITCH, BH HANDLE
SCREW, BH HANDLE
SCREW, BH HANDLE
MACHINE SCREW M5 X 16 PAN H
JSTK
3087801 B
Joystick
Page 1 of 1
Chassis Harness
Item
Part No.
1
2
3
4
5
6
7
8
Qty.
3049803
3049807
3220622
3040047
3220163
3049965
3044146
3049993
3220132
1
2
5
18
2
2
2
3
3
Description
CONNECTOR 2-WAY PLUG GRAY
WEDGELOCK 2-WAY SOCKET
CONNECTOR 3-WAY PLUG NATURAL
TERMINAL .250 22-18 AWG
RING TERMINAL 5/16 STUD
RING TERMINAL #10 STUD
CONNECTOR 12-WAY PLUG
5
4
Display
Forward
Horn 4
Motion
3
3
Drive
Speed
3
3
3
1
6
Contactor
5
4
Display
3
3
Section 1
Refer to Page CH-A
Pressure
Sensor
6
Drive
Speed
Lift
Steer R
Reverse
3
3
Steer L
7
2
7
Section 2
Refer to Page CH-B
Lift
Cylinder
7
Control Module
8
Angle
Transducer 2
Angle
Transducer 1
Stack
Harness
8
2
2
8
Lower
Controls
Interlock
Pothole
Section 3
Refer to Page CH-C
CH
1500211
Chassis Harness
Page 1 of 4
Chassis Harness
Section 1
Refer to Page CH
Pressure
Sensor
1
2
Lift
Cylinder
Angle
Transducer 2
2
Angle
Transducer 1
2
Pothole
CH-A
Page 2 of 4
1500211
Chassis Harness
Chassis Harness
Section 2
Refer to Page CH
Display
Forward
Horn 4
Motion
3
Drive
Speed
3
3
3
Drive
Speed
Lift
Steer R
Reverse
3
3
Steer L
3
3
3
Stack
Harness
CH-B
1500211
Chassis Harness
Page 3 of 4
Chassis Harness
4
5
6
6
Section 3
Refer to Page CH
Contactor
5
4
Display
7
7
7
Control Module
8
8
8
Lower
Controls
Interlock
CH-C
Page 4 of 4
1500211
Chassis Harness
Chassis Harness – Electrical System Pin ID
P1 Output and Analog Input
Wire
Description
P1-1
5V to Joystick (low current)
P1-2
Spare analog input
P1-3
0V to Joystick (low current)
P1-4
Joystick analog input
P1-5
CAN H (optional CANbus)
P1-6
CAN L (optional CANbus)
P1-7
Tilt lamp output (0V=active)
P1-8
Overload lamp output (0V=active)
P1-9
Platform alarm output (0V=active)
P2 Connects to Sensors
Wire
Description
P2-1
5V (low current, for sensors only)
P2-2
EZfit height sensor #1 input
P2-3
0V (low current, for sensors only)
P2-4
Pressure sensor input
P2-5
EZfit height sensor #2 input (optional)
P2-6
Spare analog input
P2-7
B+ feed (low current, for switches only)
P2-8
Lift down valve return (0V=active)
P2-9
Spare lamp output (0V=active)
P3 Upper Controls
Wire
Description
P3-1
EMS Platform (B+ during platform mode)
P3-2
Valve supply (high current B+ during platform mode,
supplies all valve outputs)
P3-3
Torque/traction switch (B+=active)
P3-4
Reverse/Down joystick switch (B+=active)
P3-5
Forward/Up joystick switch (B+=active)
P3-6
Drive select switch (B+=active)
P3-7
Lift select switch (B+=active)
P3-8
Steer right switch (B+=active)
P3-9
Steer left switch (B+=active)
P3-10
Spare switch input (B+=active)
P3-11
Spare switch input (B+=active)
P3-12
Trigger switch (B+=active)
CHID
1500211
Page 1 of 2
P4 Lower Controls
Wire
Description
P4-1
EMS Ground (B+ during ground mode)
P4-2
Spare switch input
P4-3
Spare switch input
P4-4
Lift down switch (B+=active in ground mode only)
P4-5
Lift up switch (B+=active in ground mode only)
P4-6
Elevation switch (B+=lowered, open=elevated)
P4-7
Spare switch input
P4-8
Spare switch input
P4-9
Spare switch input
P4-10
Spare switch input
P4-11
Spare switch input
P4-12
Spare switch input
P5 Valve Outputs
Wire
Description
P5-1
Line contactor output (B+ when active)
P5-2
Forward valve output (B+ when active)
P5-3
Reverse valve output (B+ when active)
P5-4
Brake Valve output (B+ when active)
P5-5
Motion light output (B+ when active)
P5-6
Steer left valve output (B+ when active)
P5-7
Down valve output (B+ when active)
P5-8
Steer right valve output (B+ when active)
P5-9
Torque valve output (B+ when active)
P5-10
Overload and motion alarm output (B+ when active)
P5-11
Up valve output (B+ when active)
P5-12
Spare valve output
P6 Connects to EZcal Hand-Held Device
Wire
Description
P6-1
Supply
P6-2
Receive
P6-3
Transmit
P6-4
0 V Return
CHID
Page 2 of 2
1500211
Stack Harness
Item
Part No.
1500290
1500289
1500288
1
3220205
2
3220206
3
3220176
4
5
106911-000
6
Qty.
1
1
1
1
1
4
A/R
1
A/R
Description
STACK HARNESS S3219E
CONNECTOR CIRCULAR 20-WAY PLUG
CONNECTOR CIRCULAR 20-WAY PLUG RECEPTACLE
PLUG CAVITY SIZE 20
HEATSHRINK DUAL WALL WIRES CAV 17 THROUGH 20
BOOT HDP/HD SHELL SIZE 18 GRAY
CABLE 18 GA/16 CONDUCTOR
Upper Control Box
Chassis Harness
SH
A50002A
Stack Harness
Page 1 of 1
Options
Loading Control.......................................... LDC
Loading Control
Item
1
2
3
4
5
6
7
8
9
Part No.
Qty.
3020016
510542-000 3020016 5516349
1501352
1501406
5563446
1501474
Description
1
1
1
1
1
4
1
4
1
SW TGL SPDT (M/OFF/M)
PUSHBUTTON BLACK, FLUSH MOUNT
SW TGL SPDT (M/OFF/M)
MAGNETIC LATCH
HHCS M12 X 1.75 X 90 G8.8 DIN 931
STEEL POP RIVET 3.2 X 6.1 STEEL MANDREL
PLT CABLE COVER BOTTOM
1/4-20 PAN HEAD SCREW
DECAL, LOADING CONTROL
7
8
1
2
5
3
9
6
4
LDC
1501344 C
Loading Control
Page 1 of 1
Appendix
Hydraulic Schematic..................................... HS
Hydraulic Schematic
HS
1501591 A
Hydraulic Schematic
Page 1 of 1
Product Warranty
1. Snorkel warrants each new machine manufactured and sold by it to be free from defects in material
and workmanship for a period of one (1) year from date of delivery to a Customer. The warranty will
apply subject to the machine being operated in accordance with the rules, precautions, instructions
and maintenance requirements outlined in the Snorkel Operator's and Repair Parts Manuals.
2. Snorkel further warrants the structural components, specifically the mainframe chassis, turntable,
booms and/or scissor arms of each new machine manufactured by it to be free from defects in
material and workmanship for an additional period of four (4) years. Any such part or parts which,
upon examination by the Snorkel Warranty Department, are found to be defective will be replaced or
repaired by Snorkel through its local Authorised Dealer. The structural warranty specifically excludes
adverse affects on the machine structure arising from damage, abuse or misuse of the equipment.
3. Machines may be held in an authorised Distributor stock for a maximum of six (6) months from the
date of shipment from Snorkel, before the warranty period is automatically initiated.
4. It is the responsibility of the Distributor to complete and return a Predelivery/Warranty registration,
before the act of rental/loan/demonstration of the machine or delivery to an end user.
5. The Customer and Dealer shall not be entitled to the benefits of this warranty and Snorkel shall have
no obligations here under unless the “Predelivery and Inspection Record” has been properly completed and returned to the Snorkel Warranty department within fifteen (15) days after delivery of the
Snorkel product to the Customer or Dealer’s demonstration/rental fleet. Snorkel must be notified, in
writing, within ten (10) days, of any machine sold to a Customer from a Dealer’s rental fleet during
the warranty period.
6. Any part or parts which upon examination by the Snorkel Product Support Department are found to
be defective within the specified warranty period, will be replaced or repaired at the sole discretion of
Snorkel, through Snorkel directly or an authorised Distributor, at no charge. Any parts replaced under
warranty must be original Snorkel parts obtained through Snorkel directly or an authorised Distributor, unless expressly agreed otherwise in writing and in advance by Snorkel’s Warranty Department.
7. All parts being claimed under warranty must be held available for return and inspection upon request
for a period of 90 days from date of claim submission, it is necessary that all parts are individually
tagged or marked with their part number and the warranty claim number. After 90 days all parts
replaced under warranty which have not been returned to Snorkel should be destroyed. Failure to
produce parts requested by the Warranty Administrator for inspection within a period of 14 days will
result in the claim being automatically rejected in full. Materials returned for warranty inspection
must have the following procedure:




Carefully packaged to prevent additional damage during shipping
Drained of all contents and all open ports capped or plugged
Shipped in a container tagged or marked with the RMA number
Shipped PREPAID. Any item(s) returned for warranty by any other means maybe refused and returned,
unless prior approval is agreed with Snorkel.
© Snorkel International, Inc. – all rights reserved
© Snorkel 2014
Printed in the U.S.A.
Product Warranty
8. At the direction of the Snorkel Warranty Department, any component part(s) of Snorkel products to
be replaced or repaired under this warranty program must be returned freight prepaid for inspection.
An RMA (Returns Material Authorisation) must be requested from Snorkel Warranty Department, a
copy to be placed with the returning component part(s).
9. All warranty replacement parts will be shipped freight prepaid (standard charge) from the Snorkel
Parts/Service Department or from the Vendor to Dealer or Customer.
10. All warranty claims are subject to approval by Snorkel Service Department. Snorkel reserves the right
to limit or adjust claims with regard to defective parts, labor or travel time based on usual and customary guidelines.



REPLACEMENT PARTS WARRANTY
Any part replaced under this limited warranty is not subject to further warranty cover beyond the normal
warranty period of the machine upon which the part was installed.
Any replacement parts sold (not delivered under a warranty claim) will be subject to a warranty period of
(6) six months from the date of invoice.
Parts held by a Distributor are covered under warranty for a period of (12) twelve months from the date
of invoice, provided that those parts have been subject to appropriate storage to prevent damage and
deterioration.
CLAIM PROCEDURE
The Snorkel Warranty Department must be notified within (48) forty-eight hours of any possible warranty situation
during the applicable warranty period. Personnel performing major warranty repair or parts replacement must obtain
specific approval by the Snorkel Warranty Department prior to performing the warranty repair or replacement.
When a Distributor/Customer perceive a warranty issue to exist the following steps must be adhered to:
 All warranty claims must be submitted within 30 days of the date of the machine repair
 All correspondence in respect of the claim to be on an official Snorkel warranty claim form as supplied by
Snorkel’s Warranty Department
 Allocate a warranty claim number to the repair
 Place a purchase order for genuine Snorkel replacement parts
 Snorkel to dispatch parts via the requested method (in line with the required response time)
 Confirmation that a qualified technician is available to replace the part and that this person has been accepted by Snorkel to carry out such work under the warranty of the machine. Failure to do this may nullify
the warranty.
FREIGHT DAMAGE
If a machine is received in a damaged condition, then the damage must be noted on the bill of lading and/or delivery
documents and if possible photographs taken, prior to signing acceptance of the consignment. The freight company
must be contacted by the Distributor and a damage claim registered immediately.
THIS WARRANTY EXCLUDES AND SNORKEL DOES NOT WARRANT:
1. Engines, motors, tires and batteries are manufactured by suppliers to Snorkel, who furnish their own
warranty. Snorkel will, however, to the extent permitted; pass through any such warranty protection
to the Distributor/Customer.
2. Any Snorkel product which has been modified or altered outside Snorkel factory without Snorkel written approval, if such modification or alteration, in the sole judgment of Snorkel Engineering and/or
Service Departments, adversely affects the stability, reliability or service life of the Snorkel product or
any component thereof.
© Snorkel 2014
Product Warranty
3. Any Snorkel product which has been subject to misuse and abuse, improper maintenance or accident.
“Misuse” includes but is not limited to operation beyond the factory-rated load capacity and speeds.
“Improper maintenance” includes but is not limited to failure to follow the recommendations contained in the Snorkel Operator's and Repair Parts Manuals.
4. Normal wear of any Snorkel component part(s). Normal wear of component parts may vary with the
type, application or type of environment in which the machine may be used; such as, but not limited
to sandblasting applications.
5. Routine maintenance, routine maintenance items and minor adjustments are not covered by this warranty, including but not limited to hydraulic fluid, filters and lubrication, paint and decals.
6. Any Snorkel product that has come into direct contact with any chemical or abrasive material.
7. Incidental or consequential expenses, losses, or damages related to any part or equipment failure,
including but not limited to freight cost to transport the machine to a repair facility, downtime of the
machine, lost time for workers, lost orders, lost rental revenue, lost profits, expenses or increased
cost. This warranty is expressly in lieu of all other warranties, representations or liabilities of Snorkel,
either expressed or implied, unless otherwise amended in writing by Snorkel.
8. Snorkel Warranty policy does not cover any duties, taxes, environmental fees including without limitation, disposal or handling of tires, batteries and petrochemical items.
9. Item specifically excluded are, fuel injectors, motor brushes, glow plugs, contactor tips and springs, oil
filters, lamp bulbs, lamp lenses, O-rings, coolants, lubricants and cleaning material.
10. Failure of replacement parts due to fault misdiagnosis or incorrect fitting by the Distributor/Customer.
SNORKEL MAKES NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION OF THIS LIMITED WARRANTY
SNORKEL MAKES NO IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE AND DISCLAIMS ALL LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING
BUT NOT LIMITED TO INJURY TO PERSONS OR PROPERTY.
The Customer shall make all warranty claims through Snorkel directly or an Authorised Distributor. If unable to contact
the Distributor, contact the Snorkel Service Department for further assistance.
© Snorkel 2014
Product Warranty
APPEAL
The buyer may appeal in writing against a rejected or adjusted claim to Snorkel Warranty Department within a period
of 21 days of receiving the rejection or adjustment notice. The appeal should be grounded on express reasons and
supported by relevant evidence. Appeals received outside of this time limit will not be considered.
WARRANTY SCHEDULE
Limited Warranty Periods
Warranty Period
Item
New machine materials and workmanship
1 year parts replacement
Structural components (Chassis, Turntable, Booms,
Scissors)
5 years parts replacement or repair
Parts held in a Distributor’s stock
12 months from date of invoice
Parts sold (non warranty)
Batteries
Other specifically excluded parts:
Fuel injectors
Motor brushes
Glow plugs
Contactor tips and springs
Oils
Filters
Lamp bulbs
Lamp lenses
O-rings
Coolants
Lubricants
Cleaning materials
Not covered by Warranty
© Snorkel 2014
Local Distributor / Lokaler Vertiebshändler / Distributeur local
El Distribuidor local / ll Distributore locale
EUROPE, MIDDLE EAST
AFRICA & ASIA
PHONE: +44 (0) 845 1550 058
FAX: +44 (0) 845 1557 756
NORTH & SOUTH AMERICA
PHONE: +1 785 989 3000
TOLL FREE: +1 800 255 0317
FAX: +1 785 989 3070
AUSTRALIA
PHONE: +61 1300 700 450
FAX: +61 2 9609 3057
NEW ZEALAND
PHONE: +64 6 3689 168
FAX: +64 6 3689 164

manual - Snorkel

Transcription

Similar documents

Desoutter tools

Warranty Information

Scanpan Warranty Process_1 - rtsales

July 2014

compresor nebulizador pingüino compresseur nébuliseur penguin

Snorkel feature of the month - November 2013

Jon Boats-Owner`s Manual

Energy Hog?

IDEAL STANDARD - MOMENTS VANITY BASIN

TX Systems Pricelist