docSMDK-BRIDGE-BOARD Manual
download 
Report Transcription
SMDK-BRIDGE-BOARD Manual
SMDK-BRIDGE-BOARD Manual Rev.1.00 NOTICE No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any liability of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or circuit and, further, there is no representation that this material is applicable to products requiring high level reliability, such as, medical products. Moreover, no license to any intellectual property rights is granted by implication or otherwise, and there is no representation or warranty that anything made in accordance with this material will be free from any patent or copyright infringement of a third party. This material or portions thereof may contain technology or the subject relating to strategic products under the control of the Foreign Exchange and Foreign Trade Law of Japan and may require an export license from the Ministry of Economy, Trade and Industry or other approval from another government agency. All brands or product names mentioned herein are trademarks and/or registered trademarks of their respective companies.. ©SEIKO EPSON CORPORATION 2009, All rights reserved. Scope This document applies to the SMDK-BRIDGE-BOARD released by SEIKO EPSON. Table of Contents 1. Overview............................................................................................................................................ 1 2. Jumper Settings................................................................................................................................ 2 3. SMDK Board Interface ...................................................................................................................... 3 4. EVA Board Interface.......................................................................................................................... 3 5. Power Supply .................................................................................................................................... 3 6. Appendix............................................................................................................................................ 4 6.1 External View........................................................................................................................... 4 6.2 Circuit Diagram........................................................................................................................ 5 6.3 Components List...................................................................................................................... 5 6.4 Circuit Board Dimensional Diagram......................................................................................... 5 6.5 Connection .............................................................................................................................. 6 6.6 DC5V supply for S1R72V27 EVA Boad ................................................................................... 7 6.7 S1R72V27 EVA Board Jumper settings................................................................................. 10 SMDK-BRIDGE-BOARD Manual (Rev. 1.00) Seiko Epson Corporation i 1. Overview 1. Overview This “SMDK-BRIDGE-BOARD” is a joint board between SMDK6400/6410 and S1R72V27 Evaluation Board. (Note) SMDK6400/6410 : SAMSUNG Mobile Development Kit SMDK-BRIDGE-BOARD Manual (Rev. 1.00) Seiko Epson Corporation 1 2. Jumper Settings 2. Jumper Settings Set the jumpers on the board as they are suitable for your evaluation environment. Settings marked “*” as shown Table 2-1 are default settings. No. Details Setting (* indicates default) JP1 XINT selection * 1-2 XINT connects XEINT3 1-3 XINT connects XEINT4 JP2 XDREQ selection * 1-2 XDREQ connects XuRXD_2/ExdREQ 1-3 XDREQ connects XuRXD_3/ExdREQ JP3 XDACK selection * 1-2 XDACK connects XuTXD_2/ExdACK 1-3 XDACK connects XuTXD_3/ExdACK JP4 XRESET selection * 1-2 XRESET connects nReset from SMDK 1-3 XRESET connects on this board XRESET Table 2-1 Jumper Settings Fig.2-1 Jumper Settings JP1, JP2, JP3, JP4 2 Seiko Epson Corporation SMDK-BRIDGE-BOARD Manual (Rev. 1.00) 3. SMDK Board Interface 3. SMDK Board Interface Connect JF1 on SMDK6400/6410 via CN1 on this board. Refer to “6.2 Circuit Diagrams” for pin assignment specifics. The CN1 connector and mating connector are provided as shown below. CN1 : QSE-040-01-L-D-EM2 / SAMTEC Opposite side : QTE-040-01-L-D-EM2 / SAMTEC 4. EVA Board Interface Connect CN4 on S1R72V27 Evaluation Board via CN2 on this board. Refer to “6.2 Circuit Diagrams” for pin assignment specifics. The CN2 connector and mating connector are provided as shown below. CN2 : NDS100-002-BF / Yamaichi Electronics Opposite side : NDP100-002-BF / Yamaichi Electronics 5. Power Supply This board don’t have a connector for Power Supply. It’s no need for this board to supply power especially from extenal. SMDK-BRIDGE-BOARD Manual (Rev. 1.00) Seiko Epson Corporation 3 6. Appendix 6. Appendix 6.1 External View Fig.6-1 External View CN1: SMDK Board Interface CN2: EVA Board Interface 4 Seiko Epson Corporation SMDK-BRIDGE-BOARD Manual (Rev. 1.00) 6. Appendix 6.2 Circuit Diagram Refer to attachments. 6.3 Components List Refer to attachments. 6.4 Circuit Board Dimensional Diagram External dimensions: 40.00 x 100.00 [mm] Fig.6-2 Circuit Board Dimensional Diagram [Unit: mm] SMDK-BRIDGE-BOARD Manual (Rev. 1.00) Seiko Epson Corporation 5 6. Appendix 6.5 Connection SMDK6400/6410 and SMDK-BRIDGE-BOARD connect to use External ROM Bus port (JF1) on SMDK6400/6410. Fig.6-3 Connection between SMDK6400 and S1R72V27 EVA Board JF1 Fig.6-4 Connection between SMDK6410 and S1R72V27 EVA Board JF1 6 Seiko Epson Corporation SMDK-BRIDGE-BOARD Manual (Rev. 1.00) 6. Appendix 6.6 DC5V supply for S1R72V27 EVA Boad S1R72V27 EVA Board needs to be supplied DC5V without via SMDK-BRIDGE-BOARD. Because JF1 on SMDK6400/6410 doesn’t have any pins for DC5V. On the other hands, JF1 has GND pins. So GND on SMDK6400/6410 connects both GND on SMDK-BRIDGE-BOARD and ones on S1R72V27 EVA Board. Please make a cable for DC5V to connect between SMDK6400/6410 and S1R72V27 EVA Board. Case.1 SMDK6400 to S1R72V27 EVA Board Fig. 6-5 SMDK6400 DC5V output point：J4_1pin (B_PWR_5V) Fig. 6-6 S1R72V27 EVA Board DC5V input point (red cable)：CN7_1pin SMDK-BRIDGE-BOARD Manual (Rev. 1.00) Seiko Epson Corporation 7 6. Appendix Case.2 SMDK6410 to S1R72V27 EVA Board Fig. 6-7 SMDK6410 DC5V output point：CON4_1pin (DC_5V) with SW5 sets PWR ON SW5：PWR ON Fig. 6-8 S1R72V27 EVA Board DC5V input point (red cable)：CN7_1pin 8 Seiko Epson Corporation SMDK-BRIDGE-BOARD Manual (Rev. 1.00) 6. Appendix If the current on DC5V from SMDK6400/6410 is not sufficient, supply DC5V from a external power unit to S1R72V27 EVA Board directly. In this case, turn on and off DC5V at the same timing both SMDK6400/6410 and S1R72V27 EVA Board. Case.3 a External power unit to S1R72V27 EVA Board Fig. 6-9 S1R72V27 EVA Board DC5V input point DC5V (red cable)：CN7_1pin SMDK-BRIDGE-BOARD Manual (Rev. 1.00) GND (black cable)：CN7_2pin Seiko Epson Corporation 9 6. Appendix 6.7 S1R72V27 EVA Board Jumper settings Fig6-10 CN2, CN3 CN2、SN3 CN2：1pin_2pin short CN3：1pin_2pin short Fig6-11 JP3 (Solder Jumper) JP3 JP3：CVDD_3.3V short Please set this Jumper as suitable for your evaluation environment. 10 Seiko Epson Corporation SMDK-BRIDGE-BOARD Manual (Rev. 1.00) 5 4 3 2 1 NDS100-002-BF CA[10:1] Modified 0 -> 100 ohm TP1 CA1 TP2 CA2 R1 0 B_ADDR1 CA1 R2 CA2 B_DATA1 CA3 B_DATA2 CA1 CA2 CA3 CA4 CA5 CA6 CA7 CD[15:0] R11 0 R12 0 B_DATA0 0 B_ADDR2 XBEL Modified 0 -> 56 ohm B_ADDR[10:1] CD0 TP13 CD1 D1 D R35 270 R3 0 R13 B_ADDR3 R4 0 CD2 R14 B_ADDR4 TLGV1022(F) CA4 CA8 CA9 CA10 0 LA1 LA2 LA3 LA4 LA5 0 B_DATA3 TP14 CD3 TP3 R5 0 R15 B_ADDR5 CA5 B_DATA4 CA6 B_DATA5 0 CA11 CA12 CA13 CA14 CA15 CD0 CD4 B_OEn R6 CN1 0 R16 B_ADDR6 TP4 0 CD5 CD1 TP15 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 nCS_EXT B_WEn LA11 B_ADDR2 B_ADDR4 B_ADDR6 B_ADDR8 B_ADDR10 B_ADDR12 B_ADDR14 LA7 LA9 C B_DATA0 B_DATA2 B_DATA4 B_DATA6 B_DATA8 B_DATA10 B_DATA12 B_DATA14 XEINT4 XEINT3 B_nBE1 B_nBE0 XuTXD2/ExdACK XuTXD3/ExdACK R7 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 0 B_ADDR7 B_ADDR1 B_ADDR3 B_ADDR5 B_ADDR7 B_ADDR9 B_ADDR11 B_ADDR13 B_ADDR15 CA7 R8 0 R9 0 R10 0 B_ADDR8 CA8 B_ADDR9 B_ADDR10 R17 0 R18 0 R19 0 R20 0 R21 0 R22 0 R23 0 R24 0 R25 0 R26 0 B_DATA6 CD6 B_DATA7 CA9 B_DATA8 CA10 B_DATA9 LA6 LA8 LA10 TP16 CD8 CD9 B_DATA10 CD10 B_DATA11 CD12 B_DATA13 B_DATA9 B_DATA11 B_DATA13 B_DATA15 CD8 CD9 CD10 CD11 CD12 CD13 CD14 CD15 CD11 B_DATA12 B_DATA1 B_DATA3 B_DATA5 B_DATA7 CD0 CD1 CD2 CD3 CD4 CD5 CD6 CD7 CD7 CD13 B_DATA14 CD14 B_DATA15 XCS CD15 XRD XBEH XWR TP5 B_DATA[15:0] R27 0 R28 0 TP6 B_nBE0 XuRXD2/ExdREQ XuRXD3/ExdREQ XINT TP7 nCS_EXT R29 0 R30 0 R31 0 TP8 B_OEn QSE-040-01-L-D-EM2 TP9 B_nBE1 B TP10 B_WEn R32 0 R33 0 TP11 JP1 XEINT3 2 XDREQ XDACK TP12 1 XEINT4 3 R34 0 JP2 XuRXD2/ExdREQ XRESET 2 1 XuRXD3/ExdREQ 3 J1 RST VDD GND 2 1 U1 Modified 0 -> 100 ohm JP3 XuTXD2/ExdACK 2 XuTXD3/ExdACK 3 5V MCP100-270DI/TO 1 3.3V JP4 A XnRSTOUT D2 R36 2 270 B50 A50 B49 A49 B48 A48 B47 A47 B46 A46 B45 A45 B44 A44 B43 A43 B42 A42 B41 A41 B40 A40 B39 A39 B38 A38 B37 A37 B36 A36 B35 A35 B34 A34 B33 A33 B32 A32 B31 A31 B30 A30 B29 A29 B28 A28 B27 A27 B26 A26 B25 A25 B24 A24 B23 A23 B22 A22 B21 A21 B20 A20 B19 A19 B18 A18 B17 A17 B16 A16 B15 A15 B14 A14 B13 A13 B12 A12 B11 A11 B10 A10 B9 A9 B8 A8 B7 A7 B6 A6 B5 A5 B4 A4 B3 A3 B2 A2 B1 A1 D C B A 1 U2 LA12 LA13 LA17 1 2 3 4 1A 1B 2Y GND U3 8 7 6 5 Vcc 1Y 2B 2A TC7WH00FU LA18 LA14 LA15 LA16 LA19 LA20 LA24 1 2 3 4 1A 1B 2Y GND 3 U4 Vcc 1Y 2B 2A 8 7 6 5 LA25 LA26 LA21 LA29 LA22 LA30 LA23 TC7WH02FU 1 2 3 4 1A 3Y 2A GND Vcc 1Y 3A 2Y 8 7 6 5 CN2 TLGV1022(F) LA32 LA27 LA28 LA31 Title Bridge Board TC7WH04FU Size A3 SN74LVC2G02DCTR Date: 5 4 3 2 Document Number <Doc> Monday, September 01, 2008 Rev 1.0 Sheet 1 1 of 1 SMDK-BRIDGE-BOARD Components List ■Board reference CN1 CN2 D1,D2 JP1,JP2,JP3,JP4 JS1,JS2,JS3,JS4 J1 LA1,LA2,LA3,LA4,LA5,LA6, LA7,LA8,LA9,LA10,LA11,LA 12,LA13,LA14,LA15,LA16,L A17,LA18,LA19,LA20,LA21, LA22,LA23,LA24,LA25,LA26 ,LA27,LA28,LA29,LA30,LA3 1,LA32 R1,R2,R3,R4,R5,R6,R7,R8, R27,R28,R29,R30,R31,R33, R34 R11,R12,R13,R14,R15,R16, R17,R18,R19,R20,R21,R22, R23,R24,R25,R26 R9,R10,R32 R35,R36 TP1,TP2,TP3,TP4,TP5,TP6, TP7,TP8,TP9,TP10,TP11,T P12 TP13,TP14,TP15,TP16 U1 U2 U3 U4 ■Accessory reference － Quantity 1 1 2 4 4 1 Maker Part Name ＳＡＭＴＥＣ ＹＡＭＡＩＣＨＩ ＴＯＳＨＩＢＡ MAC8 MAC8 MAC8 QSE-040-01-L-D-EM2 NDS100-002-BF ＴＬＧＶ１０２２（Ｆ） WL-1-3P JS-1 WL-1-2P 32 no_maker land 15 ROHM MCR03EZHJ101 16 ROHM 2 ＲＯＨＭ 2 ＲＯＨＭ MCR03EZHJ560 MCR03EZHJ000 MCR03EZHJ271 12 4 1 1 1 1 ＭＡＣ８ ＭＡＣ８ ＭＩＣＲＯＣＨＩＰ ＴＯＳＨＩＢＡ TI ＴＯＳＨＩＢＡ Quantity Maker 1 no_maker Note for JP1,JP2,JP3,JP4 ＬＣ－３３－Ｓ(Yellow) ＬＣ－３３－Ｓ(Black) MCP100-270DI/TO TC7WH00FU SN74LVC2G02DCTR TC7WH04FU TO-92 No mount No mount No mount Part Name Note Cable for DC5V supply from SMDK6400/6410 to S1R72V27 EVA Board Revision History Revision History Revision details Date 08/17/2009 Rev. 1.00 Page All pages Type New Details New issue International Sales Operations AMERICA ASIA EPSON ELECTRONICS AMERICA, INC. EPSON (CHINA) CO., LTD. 2580 Orchard Parkway, San Jose, CA 95131, USA Phone: +1-800-228-3964 7F, Jinbao Bldg., No.89 Jinbao St., Dongcheng District, Beijing 100005, CHINA Phone: +86-10-6410-6655 FAX: +86-10-6410-7320 FAX: +1-408-922-0238 SHANGHAI BRANCH EUROPE EPSON EUROPE ELECTRONICS GmbH Riesstrasse 15, 80992 Munich, GERMANY Phone: +49-89-14005-0 FAX: +49-89-14005-110 7F, Block B, Hi-Tech Bldg., 900 Yishan Road, Shanghai 200233, CHINA Phone: +86-21-5423-5522 FAX: +86-21-5423-5512 SHENZHEN BRANCH 12F, Dawning Mansion, Keji South 12th Road, Hi-Tech Park, Shenzhen 518057, CHINA Phone: +86-755-2699-3828 FAX: +86-755-2699-3838 EPSON HONG KONG LTD. 20/F, Harbour Centre, 25 Harbour Road, Wanchai, Hong Kong Phone: +852-2585-4600 FAX: +852-2827-4346 Telex: 65542 EPSCO HX EPSON TAIWAN TECHNOLOGY & TRADING LTD. 14F, No. 7, Song Ren Road, Taipei 110, TAIWAN Phone: +886-2-8786-6688 FAX: +886-2-8786-6660 EPSON SINGAPORE PTE., LTD. 1 HarbourFront Place, #03-02 HarbourFront Tower One, Singapore 098633 Phone: +65-6586-5500 FAX: +65-6271-3182 SEIKO EPSON CORP. KOREA OFFICE 50F, KLI 63 Bldg., 60 Yoido-dong, Youngdeungpo-Ku, Seoul 150-763, KOREA Phone: +82-2-784-6027 FAX: +82-2-767-3677 SEIKO EPSON CORP. SEMICONDUCTOR OPERATIONS DIVISION IC Sales Dept. IC International Sales Group 421-8, Hino, Hino-shi, Tokyo 191-8501, JAPAN Phone: +81-42-587-5814 FAX: +81-42-587-5117 Document Code: 411806600 First Issue August 2009, JAPAN