Data Sheet (English)

Visual PLC
5.7" display, PROFIBUS-DP - VT250 series (Economy)
VT250-57P-L7-DPM
■ TFT LCD color display
■ 5.7’’, 320 x 240 pixels, 65K colors
■ Resistive Touch
■ 2 x RJ45 real-time Ethernet interface
■ Serial interface RS232/485 and USB device
■ PROFIBUS-DP master
■ Programmable with CoDeSys V3 acc.to
IEC 61131-3
■ 32 Bit RISC processor 200 MHz
■ 4 MB program and data memory
(CoDeSys and QViS project files)
■ 16 kB non-volatile memory
Type designation
Ident no.
VT250-57P-L7-DPM
6828009
Function
PLC with integrated touch display
Display / Touch
Display
Touch
Active screen area
Resolution (pixels)
Number of usable colours
TFT LCD colour display
resistive
5.7'' (approx. 118 * 89 mm)
320 x 240 (240 * 320 with edgewise design)
65536 colours
Controller
Processor
Program and data memory
Remanent memory
Add-on memory
Real time clock
Operating system
ARM9, 32 bit, 200 MHz
4 MB (CoDeSys and QViS)
16 kB SDRAM
1 x SD/MMC memory card
yes
rcX
Programming
CODESYS V.3
Interfaces
Ethernet
Protocols
Fieldbus
USB
Serial
Double (integrated switch)
PROFIBUS-DP (Master)
Modbus TCP (Master/Slave)
Modbus RTU (Master/Slave)
PROFIBUS-DP (Master)
Device
RS232 / RS485
Power supply
Rated value
Admissible voltage range
24 VDC reverse-polarity protected, 0.35 A maximum
20.4…28.8VDC
General data
Operating ambient conditions
Edition • 2016-09-21T21:15:31+02:00
Storage ambient conditions
Approvals
Protection class
Dimensions
Front (W x H x D)
Cut-out (W x H)
Weight
1/3
■ SD/MMC memory card
■ Front face protected, class IP65
The HMI touch panel with a 5.7“ TFT display
can be used both as operator and control terminal.
The control software applied is CoDeSys V3
and approved according to the international
standard IEC 61131-3.
QViS is the software used for visualization
and especially developed for embedded systems.
The exchange of variables between control
unit and visualization is implemented via interface. The HMI panel is equipped with all relevant RT Ethernet and fieldbus systems.
0…50 °C, 10…90 % relative humidity, non-condensing
-20…60 °C, 10…95 % relative humidity, non-condensing
CE, cULus
IP65 front
IP20 rear
212x156x50mm
198x142mm
approx. 0.7 kg
Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ [email protected] ñ www.turck.com
Visual PLC
5.7" display, PROFIBUS-DP - VT250 series (Economy)
VT250-57P-L7-DPM
Connection and pin assignment
Power Supply
Pin Assignment
Nominal voltage 24 VDC
Nominal current 0.35 A
PROFIBUS / MPI Fieldbus Interface
Pin Assignment
SUB-D female connector, 9-pole
Ethernet Ports
Pin Assignment
2 x RJ45 jack
Integrated switch
10/100 Mbps
RS232 Interface
Pin Assignment
SUB-D male connector, 9-pole
Attention:
Edition • 2016-09-21T21:15:31+02:00
Do not connect pins 1, 4, 6 and 9 when using RS232!
2/3
Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ [email protected] ñ www.turck.com
Visual PLC
5.7" display, PROFIBUS-DP - VT250 series (Economy)
VT250-57P-L7-DPM
USB Interface
Pin Assignment
USB device
Edition • 2016-09-21T21:15:31+02:00
Service interface
3/3
Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ [email protected] ñ www.turck.com