Cast-In-PlaCe (wet-set) RePlaCeable taCtIle

Transcription

Cast-In-PlaCe (wet-set) RePlaCeable taCtIle
5-Year
Warranty
Proudly Made in
the U.S.A.
Cast-In-Place (wet-set)
Replaceable Tactile
www.adatile.com • 800-372-0519
Cast-In-Place (wet-set)
Replaceable Tactile
2
Proudly Made in
the U.S.A.
In stock colors
White
37875
Brick Red
20109
Yellow
33538
Blue
15187
Safety Red
31350
Seattle Yellow
23594
US Patents*
*www.adatile.com/patents
Black
37038
Dark Gray
36081
Clay Red
22144
3
Cast-In-Place Replaceable Tactile
Installation Procedure
Be sure to read and understand all of these instructions before you begin.
A. The physical characteristics of the concrete shall be as specified in the contract
documents while maintaining a slump range of 4-7 inches to permit the solid
placement of the ADA Cast-In-Place Replaceable Tactile Unit (ADAREP) in the
wet cement.
B.The concrete shall be poured and finished level, true and smooth to
the required dimensions prior to the placement of the ADAREP unit.
C. Place the ADAREP unit 6-8 inches from the curb line. Working in a
grid pattern, tamp the ADAREP unit into the wet concrete using a rubber
mallet and a piece of wood. Continue this process until all of the air has
been released, and the ADAREP unit surface is flush with the surrounding area.
IMPORTANT: Avoid striking the surface of the ADAREP unit directly.
D.Following the placement, the ADAREP unit elevation should be checked to
Pull-Strength
6200 P.S.I.
the adjacent surface with a straight edge. The ADAREP unit elevation should
be consistent with the Contract Drawings and Specifications. Any required
adjustments must be made prior to the time when the concrete begins to set.
E. Important Notice to Installer: To allow for expansion and contraction,
after tile is installed, use a 1/4” finish edge trowel around entire perimeter. On a continous
run, be sure to space each unit 1/8” apart.
F. When you are confident that the ADAREP unit is in place and no further ad-
justments are needed, place a cinder block on both ends, if necessary, to hold the
ADAREP unit in place while the concrete sets.
G. During and after the ADAREP unit installation, as well as the concrete curing
stage, no walking or external forces can be placed on the ADAREP unit. The area
must be protected from pedestrian traffic until concrete is cured. The ADAREP
Warning Surface will be ready for pedestrian traffic within 2-4 hours.
H.Be sure to remove plastic
protective covering from the face
of the ADAREP Unit once the
concrete is cured.
*Not recommended or warrantied for
asphalt installation.
Do not cut Cast-In-Place Replaceable Tactile. Use an appropriate
sized tactile or Radius Tactile to fit the requirement.
Contact manufacturer for more details.
4
www.adatile.com • 800-372-0519
PRODUCT SIZES
2’x3’ 2’x4’ 2’x5’
3’x4’ 3’x5’
APPLICATION
Fresh Pour
Concrete Ramps
& Replacement
Cast-In-Place Replaceable Tactile
(WET-SET)
Replacement Procedure
Be sure to read and understand all of these
instructions before you begin.
A. Lift the existing composite bolt cap from each anchor location on the
ADA Cast-In-Place Replaceable Tactile unit (ADAREP) with a flat head
screw driver.
B.Remove the existing 1/2” x 1½” heavy duty steel bolts and washers from
each anchor location on the ADAREP unit with a ratchet. Save & reuse.
C. Tap around all sides of the ADAREP unit and across the middle with a
rubber mallet, working in a grid pattern.
D. Pry the existing ADAREP unit from the concrete ramp with a small
prybar, working around the edges until it can be lifted cleanly away.
E. Be sure to remove all small debris and dust from the existing impression
in the concrete ramp.
IMPORTANT: Be careful not to get debris into anchor locations.
F. Replace new ADAREP unit, of same size and orientation, into impression
in concrete ramp. Lightly tamp down the ADAREP unit with a rubber
mallet and a piece of wood. Continue this process until the ADAREP unit
is set firmly into existing impression in concrete ramp.
IMPORTANT: Avoid striking the ADAREP unit directly.
G. Bolt existing 1/2” x 1½” heavy duty steel bolts and washers back into each
anchor location on new ADAREP unit.
H.Snap a new composite bolt cap provided, into each anchor location
on the ADAREP unit. The ADAREP unit is ready for pedestrian
traffic immediately after installation is complete.
View additional photos, drawings and
specifications on our website: www.adatile.com.
Call (800) 372-0519 with any questions.
US Patents*
*www.adatile.com/patents
www.adatile.com • 800-372-0519
5
24.
21.
14.
Cast-In-Place Replaceable Tactile
B
B
PATENT PENDING
1.250
34.286
Inline
Dome
Pattern
VIEW-D
15 - EQUAL SPACES
DOME GEOMETRY
NOTE: US PATENT PENDING APPEARS ON
TOP SIDE OF PART AS SHOWN.
AIR VENTS AROUND THE
OUTSIDE EDGES OF PANEL
VIEW -B
PANEL DIMENSIONS
CAP COVER
.045 HIGH
TYP.
ADA Cast-In-Place
Replaceable
Tactile units (ADAREP) are available in 24” x 36”,
.900
DIA. TYP.
60.000°
.500
24” x 48”, 24” x DIA.
60”,TOP
36”
x
48”
and
36”
x 60”
sizes. ADAREP units may also be custom
OF DOMES
1.375
DIA.
(4)
configured to accommodate specific project
requirements. ADAREP units measure
1.125
DIA.
(4)
¼” nominal thickness and feature a ⅜” thick
x 1” wide perimeter “flange.”
0.6250
(4)
0.875
(4)
.090 DEG. POINTS
Recessed
Anchor
Location
2.350
In accordance with ADA Regulations for Detectable Warning on Curb Ramps: Raised
truncated domes with a diameter of nominal 0.9”, a height of nominal 0.2” and a
center-to-center spacing of 2.35”.
MATERIAL
0.250
0.250
0.312
0.062
0.870
0.245
0.200
0.625
2.350
A durable exterior grade homogenous glass, carbon and fiberglass reinforced
composite material which is colorfast and UV stable. The color of the ADAREP unit
is uniform throughout and does not rely on any type of paint
R0.250coating to achieve color stability. Standard colors include: Federal
TYP.
Yellow, Seattle Yellow, White, Brick Red, Clay Red, Safety Red, Blue, Dark Gray and Black. For superior wheelchair, walker
HEX HEAD BOLTS & WASHER 4-PL.
and shopping cart mobility, truncated domes have a center-to-center (horizontally and vertically) spacing of 2.35 inches.
PHYSICAL CHARACTERISTICS
Compressive Strength Flexural Strength
Water Absorption
Slip Resistance
Flame Spread Index
Salt Spray
Chemical Stain Testing
Abrasion Resistance
Accelerated Weathering
Tensile Strength
Load Bearing at 16,000 lbs.
Freeze/Thaw/Heat
28,900 psi
29,300 psi
.07%
1.18 Dry, 1.05 Wet
20
No Change (200 hours)
No Deterioration
549
Delta E<5.0 (2,000 hours) 11,600 psi
No Damage
No Disintegration
ASTM D 695
ASTM D 790
ASTM D 570
ASTM C 1028
ASTM E 84
ASTM B 117
ASTM 1308
ASTM C 501
ASTM G 155
ASTM D 638
AASHTO-H20
ASTM C 1026
5-Year
Warranty
INCIDENTALS
Fasteners: ½” x 1½”
heavy duty steel
bolts and washers.
Anchors: 1½” corrosion
resistant concrete inserts.
WARRANTY
ADAREP units shall be guaranteed in writing
for a period of five (5) years from date of contract’s
final completion. The guarantee includes breakage and
deformation of the tactile warning
surface material.
6
www.adatile.com • 800-372-0519
Color
Throughout
VIEW -B
DIA. TOP OF DOMES
.450
.090 DEG. POINTS
.045 HIGH TYP.
0.245
34.286
.900
DIA. TYP.
VIEW -B
3 x SIZE
DIA.(8)
1.125
DIA.(8)
1.375
60.000°
SECTION A-A
SIDE VIEW
15 - EQUAL SPACES
0.22
1.200
9 - EQUAL SPACES
24.000
21.600
14.400
1.200
VIEW-D
0.967
TOP VIEW
0.500
1.250
0.200
0.722
www.adatile.com • 800-372-0519
0.062
HEX HEAD BOLTS & WASHER 8-PL.
TYP.
R0.250
*www.adatile.com/patents
A
NOTE: U.S. Patents*
CAP COVER
US PATENT # 7,779,581
0.6250
(8)
A
0.875
(8)
2.350
VIEW - " D" 2 x SIZE
FIELD DOT 7 DOME LAYOUT
2.350
AIR VENTS LOCATED ON
THE ENDS OF THE TWS UNIT
TACTILE WARNING SURFACE
VIEW
2436NV8REP_
PART NO.
DATE
www.adatile.com
(800)372-0519
P.O. Box 3
N.Billerica, Ma. 01862
ADA-REP2436
DRAWING NO.
WET SET ADA STD REPLACEABLE TACTILE
WARNING SURFACE UNIT
8-BOLT LOCATIONS
2.350" IN LINE TRUNCATED DOME PATTERN
PART SIZE 24" x 36"
PLANS AND DETAILS
PROJECT
SMC COMPOSITE
MATERIAL
TRADE
BOTTOM
(WET-SET)
0.250
36.000
27.429
Cast-In-Place Replaceable Tactile
24”x36” (610 x 914mm) Tile
2.35” (59.7 mm) Dome Spacing
7
Cast-In-Place Replaceable Tactile
24”x48” (610 x 1219mm) Tile
2.35” (59.7 mm) Dome Spacing
0.245
9.1429
1.250
18.286
.900
DIA. (8)
48.000
20.571
2.286
9.1429
45.714
TOP VIEW
20 - EQUAL SPACES
SIDE VIEW
CAP COVER
SECTION A-A
60.000°
1.375
TYP.
R 0.250
HEX HEAD BOLTS & WASHER 8-PL.
US PATENT # 7,779,581
A
AIR VENTS LOCATED ON
THE ENDS OF THE TWS UNIT
*www.adatile.com/patents
NOTE: U.S. Patents*
2.350
VIEW - " D" 2 x SIZE
FIELD DOT 7 DOME LAYOUT
2.350
A
VIEW-D
0.200
0.722
DIA. TYP.
0.875
(8)
VIEW -B
.090 DEG. POINTS
.045 HIGH TYP.
.450
DIA. (8)
1.125
0.6250
(8)
0.250
(8)
DIA. TOP OF DOMES
0.500
VIEW -B 3 x SIZE
BOTTOM
VIEW
TACTILE WARNING SURFACE
SMC COMPOSITE
MATERIAL
TRADE
PROJECT
2448NV8REP_
PART NO.
DATE
WET SET ADA REPLACEABLE TACTILE
WARNING SURFACE UNIT
8-BOLT LOCATIONS
2.350" IN LINE TRUNCATED DOME PATTERN
PART SIZE 24" x 48"
PLANS AND DETAILS
ADA-REP2448
DRAWING NO.
www.adatile.com
(800)372-0519
P.O. Box 3
N.Billerica, Ma. 01862
www.adatile.com • 800-372-0519
8
0.22
0.062
1.200
9 - EQUAL SPACES
24.000
21.600
14.400
1.200
0.967
1.200
9 - EQUAL SPACES
VIEW -B
0.245
0.967
DIA. TOP OF DOMES
.450
.090 DEG. POINTS
.045 HIGH TYP.
24.000
21.600
14.400
1.200
VIEW-D
1.250
.900
DIA. TYP.
0.22
DIA.(11)
VIEW -B 3 x SIZE
DIA.(11)
1.125
1.375
60.000°
57.143
CAP COVER
SECTION B-B
SIDE VIEW
25 - EQUAL SPACES
TOP VIEW
13.714
0.875
(11)
6.314
0.500
60.000
TYP.
R0.250
HEX HEAD BOLTS & WASHER 11-PL.
18.286
6.314
US PATENT # 7,779,581
VIEW - " D" 2 x SIZE
FIELD DOT 7 DOME LAYOUT
2.350
AIR VENTS LOCATED ON
THE ENDS OF THE PANEL
*www.adatile.com/patents
NOTE: U.S. Patents*
B
2.350
B
0.200
0.722
www.adatile.com • 800-372-0519
0.062
0.6250
(11)
BOTTOM VIEW
TACTILE WARNING SURFACE
2460NV11REP_
PART NO.
DATE
www.adatile.com
(800)372-0519
P.O. Box 3
N.Billerica, Ma. 01862
ADA-REP2460
DRAWING NO.
WET SET ADA REPLACEABLE TACTILE
WARNING SURFACE UNIT
11-BOLT LOCATIONS
2.350" IN LINE TRUNCATED DOME PATTERN
PART SIZE 24" x 60"
PLANS AND DETAILS
PROJECT
SMC COMPOSITE
MATERIAL
TRADE
(WET-SET)
0.250
(11)
18.286
Cast-In-Place Replaceable Tactile
24”x60” (610 x 1524mm) Tile
2.35” (59.7 mm) Dome Spacing
9
Cast-In-Place Replaceable Tactile
36”x48” (914 x 1219mm) Tile
2.35” (59.7 mm) Dome Spacing
A
1.143
18.286
36.000
PART O.A.
PART O.A.
20.571
CAP COVER
A
AIR VENTS AROUND THE
OUTSIDE EDGES OF PANEL
1.143
13.500
13.500
48.000
2.286
45.714
20 - EQUAL SPACES
B-B
SIDE VIEW
SECTION
DIA. (12)
1.375
TYP.
R 0.250
HEX HEAD BOLTS & WASHER 12-PL.
U.S. Patents*
*www.adatile.com/patents
2.350
BOTTOM VIEW
VIEW - " D" 2 x SIZE
FIELD DOT 13 ON DOME LAYOUT
2.350
33.750
VIEW-D
0.245
60.000°
DIA. (12)
1.125
0.875
(12)
VIEW-B
.900
DIA. TYP.
0.500
.090 DEG. POINTS
.045 HIGH TYP.
0.200
0.722
.450
0.062
0.562
VIEW -B 3 x SIZE
QT'Y
SEE MATERIAL LIST
PART NO.
PART NO.
MATERIAL LIST
ITEM DESCRIPTION
3
2
1
4
SCALE
AS NOTED
FULL SIZE
TRADE
DETECTABLE WARNING SURFACE
PROJECT
MATERIAL
REV. NO.
WET SET ADA REPLACEABLE TACTILE
WARNING SURFACE UNIT
2.375" IN LINE TRUNCATED DOME PATTERN
PART SIZE 36" x 48"
PLANS AND DETAILS
DRAWING NO.
www.adatile.com
(800)372-0519
P.O. Box 3
N.Billerica, Ma. 01862
www.adatile.com • 800-372-0519
10
0.6250
(12)
0.250
(12)
DIA. TOP OF DOMES
0.967
1.125
15 - EQUAL SPACES
1.125
www.adatile.com • 800-372-0519
.450
.090 DEG. POINTS
.045 HIGH TYP.
0.245
DIA. TOP OF DOMES
VIEW-B
0.967
.900
DIA. TYP.
0.562
VIEW -B 3 x SIZE
DIA. (12)
1.125
DIA. (12)
1.375
60.000°
SECTION B-B
SIDE VIEW
57.143
20 - EQUAL SPACES
CAP COVER
HEX HEAD BOLTS & WASHER 12-PL.
TYP.
R 0.250
16.000
AIR VENTS AROUND THE
OUTSIDE EDGES OF PANEL
1.143
13.500
"B"
13.500
33.750
36.000
PART O.A.
1.125
15 - EQUAL SPACES
1.125
VIEW-D
0.500
1.143
0.062
59.429
0.875
(12)
18.286
*www.adatile.com/patents
U.S. Patents*
2.350
VIEW - " D" 2 x SIZE
FIELD DOT 13 ON DOME LAYOUT
2.350
"B"
0.200
0.722
0.6250
(12)
BOTTOM VIEW
AS NOTED
FULL SIZE
PART NO.
SEE MATERIAL LIST
QT'Y
www.adatile.com
(800)372-0519
P.O. Box 3
N.Billerica, Ma. 01862
DRAWING NO.
REV. NO.
WET SET ADA REPLACEABLE TACTILE
WARNING SURFACE UNIT
2.375" IN LINE TRUNCATED DOME PATTERN
PART SIZE 36" x 60"
PLANS AND DETAILS
PROJECT
MATERIAL
PART NO.
MATERIAL LIST
TRADE
DETECTABLE WARNING SURFACE
SCALE
4
3
2
1
ITEM DESCRIPTION
(WET-SET)
0.250
(12)
16.000
Cast-In-Place Replaceable Tactile
36x60” (914 x 1524mm) Tile
2.35” (59.7 mm) Dome Spacing
11
Product Information / Submittal
www.adatile.com • 800-372-0519
4/13

Similar documents