Cat Telehandler Product Specs

Cat
®
TH255
Telehandler
Specifications
Engine
Model Gross Power Maximum Torque Displacement Hydraulic System — Implement
Cat C4.4 Stage IIIA DIT
63 kW
84 hp
353 Nm/1400 rpm
4.4 litre
Pump Type
Single Section Gear Pump
Maximum system
pressure 240 bar
Maximum Pump Flow 85 litre/min
• Auxiliary Hydraulic Circuit used for all attachments
equipped with cylinders or other hydraulic components.
Consists of valves, controls, and hydraulic lines.
5897 kg
Transmission
®
Weights
Operating Weight with
Carriage and Forks
Operating Specifications
Rated Load Capacity
Maximum Lift Height Maximum Forward Reach Top Travel Speed Load at Max Height Load at Max Reach Turning Radius Over Tyres Turning Radius Over Forks
2500 kg
5600 mm
3250 mm
26 km/h
2500 kg
940 kg
3200 mm
4254 mm
Service Refill Capacities
Fuel Tank Hydraulic System 91 litre
98 litre
Tyres
Standard 14.00 x 17.5 Foam Filled
Brakes
Service Brakes Inboard wet disc brakes on front axle
Parking Brakes Wet disc spring-applied hydraulic release
• Light on dash indicates when brake is on.
Axles
• Planetary on front and rear axles.
• High bias limited slip differential on front axle.
Transmission Forward Reverse Hydrostatic
Variable Speed
Variable Speed
Boom Performance
Boom Up Boom Down Tele In Tele Out Bucket Dump Bucket Crowd Drawbar Pull (Loaded) 6.2 Seconds
4.3 Seconds
3.4 Seconds
6.3 Seconds
2.0 Seconds
2.4 Seconds
38.7 kN
Instruments
• Indicators for machine hours, fuel-level, steer mode,
steering pressure, battery charge, coolant temperature,
parking brake and engine pre-heat.
• Reverse motion alarm.
• Panel and switches are illuminated for night operation.
TH255 Telehandler
Dimensions
All dimensions are approximate.
TL255
1920 mm
279 mm
1820 mm
2290 mm
3660 mm
Load Chart and Dimensions
IMPORTANT
6m
70°
0m
4m
0°
2500 kg
30 40
50 60
1500 kg
2000 kg
70 80
2500 kg
60
940 kg
3m
B
A
-10
2m
1m
70
80
5
TL25
10°
C
20
10
1m
20°
80
-10
2m
30°
70
5
TL25
40°
3m
30 40
50 60
D
50°
4m
20
10
5m
-10
E
60°
Rated lift capacities shown are with machine
equipped with standard carriage and pallet
forks. When lifting loads, the machine requires
a firm surface with undamaged, properly inflated
tyres. Machine specifications and stability are
based on rated lift capacities at specific boom
angles and boom lengths. (If specifications
are critical, the proposed application should
be discussed with your dealer.)
0m
10
20 30
40 50
DO NOT exceed rated lift capacity loads,
as unstable and dangerous machine
conditions will result.
DO NOT tip the machine forward
to determine the allowable load.
TL255
Due to continuous product improvements, machine
specifications and/or equipment changes may
be made without prior notification. This machine
meets or exceeds AS1418.19-2007 as originally
manufactured for intended applications.
600 mm
For more complete information on Cat products, dealer services, and industry solutions, visit us on the web at
www.cat.com
© 2 009 Caterpillar
All rights reserved.
CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow” and the POWER EDGE trade dress, as well as
corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
AEHQ6033-01 (10-2009)
Cat
®
TH336
Telehandler
Specifications
74.5 kW Engine
93.1 kW Engine
Engine
Engine
Standard
Optional
Gross Power
Standard Optional Maximum Torque
Standard Optional Bore Stroke Displacement • All engine horsepower (hp) are metric.
Hydraulic System
Cat C4.4 DITAAC
Cat® C4.4 DITAAC-ACERT ™
®
74.5 kW/101 hp
93.1 kW/126 hp
410 Nm/1400 rpm
496 Nm/1400 rpm
105 mm
127 mm
4.4 litre
Weights
Operating Weight Non-Agriculture Agriculture 6573 kg
6693 kg
Operating Specifications
Rated Load Capacity Maximum Lift Height Maximum Forward Reach Top Travel Speed Load at Max Height Load at Max Reach Turning Radius Over Tyres
Turning Radius Over Forks
3000 kg
6100 mm
3109 mm
40 km/h
2250 kg
975 kg
3700 mm
4670 mm
Service Refill Capacities
Fuel Tank Hydraulic Tank 150 litre
90 litre
Tyres
Standard 15.5/80-24 16PR
Brakes
Service Brakes Parking Brakes Servo assisted on front axle
Mechanical on front axle
Sound
Operator Sound Exterior Sound
106 dB (A)
107 dB (A)
78 dB(A)
Maximum System Pressure Maximum Pump Flow Pump Type
Auxiliary Hydraulic Supply
Intermittent Continuous 250 bar
113 litre/min
Variable Displacement
Load Sensing Axial
Piston Pump
80 litre/min
60 litre/min
Transmission Speeds
Forward
1
2
3
4
5*
Reverse
1
2
3
7 km/h
12 km/h
21 km/h
32 km/h
40 km/h
7 km/h
12 km/h
21 km/h
* ACERT engine option only
Boom Performance
Boom Up Boom Down Tele In Tele Out Crowd Forward (dump) Crowd Backward Combined
Up and Out Down and In Drawbar Pull 74.5 kW Drawbar Pull 93 kW Bucket Breakout Force to ISO 8313 Boom Breakout Force
6.0 Seconds
4.0 Seconds
5.0 Seconds
5.0 Seconds
3.0 Seconds
3.0 Seconds
10.0 Seconds
7.0 Seconds
82,4 kN
86,8 kN
55 kN
36 kN
TH336 Telehandler
Dimensions
All dimensions are approximate.
920 mm – agricultural
880 mm – non agricultural
2323 mm
1753 mm
430 mm
375 mm
2950 mm
4253 mm
1988 mm
2400 mm
4621 mm
Load Chart and Dimensions
7m
IMPORTANT
2250 kg
6m
67.5º
2700 kg
50º
5m
4m
30º
3m
1m
10º
975 kg
2m
20º
1300 kg
1500 kg
1750 kg
40º
DO NOT exceed rated lift capacity loads, as unstable and dangerous machine
conditions will result.
3000 kg
0º
4m
3m
2m
Rated lift capacities shown are with machine equipped with standard carriage and pallet forks. When lifting loads, the machine requires a firm surface with undamaged, properly inflated tyres. Machine specifications and stability are based on rated lift capacities at specific boom angles and boom lengths. (If specifications are critical, the proposed application should be discussed with your dealer.)
1m
DO NOT tip the machine forward to determine the allowable load.
Due to continuous product improvements, machine specifications and/or equipment changes may be made without prior notification. This machine meets or exceeds AS1418.19-2007 as originally manufactured for intended applications. When utilising a suspended load, the JLG Load Management Indicator System (LMIS) must be installed in order to remain compliant with AS1418.19-2007.
600 mm
For more complete information on Cat products, dealer services, and industry solutions, visit us on the web at www.cat.com
© 2010 Caterpiller
All rights reserved.
CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow” and the POWER EDGE trade dress, as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
AEHQ6050-02 (03-2010)
Cat
®
TH406
Telehandler
Specifications
Engine
Hydraulic System
Model
Standard
Optional
Gross Power
Standard
Optional
Maximum Torque
Standard
Optional
Bore
Stroke
Displacement
• All engine horsepower (hp) are metric.
Cat ® C4.4 DITAAC
Cat ® C4.4 DITAAC ACERT ™
74.5 kW/101 hp
93.1 kW/126 hp
410 Nm/1400 rpm
496 Nm/1400 rpm
105 mm
127 mm
4.4 litre
Weights
Operating Weight with Carriage & Forks
Non-Agriculture
7200 kg
Agriculture
7320 kg
Operating Specifications
Rated Load Capacity
Maximum Lift Height
Maximum Forward Reach
Top Travel Speed
Load at Max Height
Load at Max Reach
Outside Turning Radius Over Tyres
Outside Turning Radius Over Forks
3700 kg
6100 mm
3109 mm
40 km/h
2500 kg
1500 kg
3700 mm
4670 mm
Service Refill Capacities
Fuel Tank
Hydraulic Tank
150 litre
90 litre
Tyres
Standard
15.5/80-24 16PR
Brakes
Service Brakes
Parking Brakes
Servo assisted on front axle
Mechanical on front axle
Sound
Operator Sound Exterior Sound
(74.5 kW Engine)
(93.1 kW Engine)
78 dB(A)
106 dB (A)
107 dB (A)
Maximum System Pressure Maximum Pump Flow
Pump Type
Auxiliary Hydraulic Supply
Intermittent Continuous 250 bar
150 litre/min
Variable displacement load sensing axial piston pump
80 litre/min
60 litre/min
Transmission Speeds
Forward
1
2
3
4
5 (ACERT engine option only)
Reverse
1
2
3
7 km/h
12 km/h
21 km/h
32 km/h
40 km/h
7 km/h
12 km/h
21 km/h
Boom Performance
Boom Up Boom Down Tele In Tele Out Crowd Forward (dump) Crowd Backward Combined
Up and Out Down and In Drawbar Pull 74.5 kW
Drawbar Pull 93.1 kW
Bucket Breakout Force to ISO8313 Boom Breakout Force
5.0 Seconds
4.0 Seconds
4.5 Seconds
5.0 Seconds
3.0 Seconds
3.0 Seconds
8.0 Seconds
6.0 Seconds
82,4 kN
86,8 kN
55 kN
36 kN
TH406 Telehandler
Dimensions
All dimensions are approximate.
920 mm — agricultural
880 mm — non-agricultural
2323 mm
1753 mm
430 mm
662 mm
2950 mm
1988 mm
4253 mm
2382 mm
4621 mm
Load Chart and Dimensions
TH406
IMPORTANT
2000 kg
2m
1500 kg
3m
20°
3700 kg
30°
B
40°
4m
3m
3000 kg
2500 kg
4m
2m
B
A
DO NOT exceed rated lift capacity loads, as unstable and dangerous machine
conditions will result.
DO NOT tip
the machine forward 30°
to determine the allowable load.
3700 kg
A
40°
5m
2500 kg
B
5m
C
Due to continuous product improvements, machine specifications and/or equipment 20°
changes
may be made without prior notification.
10°
3000 kg
50°
6m
2000 kg
B
C
6m
Rated lift capacities shown are with67.5°
machine
equipped with carriage and pallet forks. The machine must be level on a firm surface with
undamaged, properly inflated tyres. Machine
specifications and stability
50°are based on rated lift capacities at specific boom angles and boom
lengths. (If specifications are critical, the proposed
application should be discussed with your dealer.)
1500 kg
67.5°
10°
1m
1m
0°
0m
4m
0°
0m
3m
2m
1m
0m
500 mm
For more complete information on Cat products, dealer services, and industry solutions, visit us on the web at www.cat.com
© 2010 Caterpillar
All rights reserved.
CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow” and the POWER EDGE trade dress, as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
4m
3m
2m
1m
0m
500 mm
HEHB3859-05 (02-2010)
Cat
®
TH407
Telehandler
Specifications
Engine
Hydraulic System
Model
Standard
Optional
Gross Power
Standard
Optional
Maximum Torque
Standard
Optional
Bore
Stroke
Displacement
Cat® C4.4 DITAAC
Cat® C4.4 DITAAC-ACERT™
74.5 kW
93.1 kW
101 hp
126 hp
410 Nm/1400 rpm
496 Nm/1400 rpm
105 mm
127 mm
4.4 litre
Weights
Operating Weight with Carriage & Forks
Non-Agriculture
7700 kg
Agriculture
7820 kg
Operating Specifications
Rated Load Capacity
Maximum Lift Height
Maximum Forward Reach
Top Travel Speed
Load at Max Height
Load at Max Reach
Turning Radius Over Tyres
Turning Radius Over Forks
3700 kg
7300 mm
3763 mm
40 km/h
2000 kg
1300 kg
3750 mm
4740 mm
Service Refill Capacities
Fuel Tank
Hydraulic Tank 150 litre
90 litre
Tyres
Standard
15.5/80-24 16PR
Brakes
Service Brakes
Parking Brakes
Servo assisted on front axle
Mechanical on front axle
Sound
Operator Sound
Exterior Sound
74.5 kW Engine
93.1 kW Engine
78 dB(A)
106 dB(A)
107 dB(A)
Maximum System Pressure
Maximum Pump Flow
Pump Type
Auxiliary Hydraulic Supply
Intermittent
Continuous
250 bar
150 litre/min
Variable displacement load sensing axial piston pump
80 litre/min
60 litre/min
Transmission Speeds
Forward
1
2
3
4
5 *
Reverse
1
2
3
7 km/h
12 km/h
21 km/h
32 km/h
40 km/h
7 km/h
12 km/h
21 km/h
* ACERT engine option only
Boom Performance
Boom Up
Boom Down
Tele In
Tele Out
Crowd Forward (dump)
Crowd Backward
Combined
Up and Out
Down and In
Drawbar Pull 74.5 kW
Drawbar Pull 93.1 kW
Bucket Breakout Force to ISO 8313
Boom Breakout Force
7.5 Seconds
5.1 Seconds
4.8 Seconds
5.7 Seconds
3.0 Seconds
3.0 Seconds
11.5 Seconds
6.6 Seconds
83,4 kN
87,3 kN
65 kN
42 kN
TH407 Telehandler
Dimensions
All dimensions are approximate.
920 mm — agricultural
880 mm — non-agricultural
2385 mm
1838 mm
430 mm
962 mm
3050 mm
1988 mm
4679 mm
2382 mm
5153 mm
Load Chart and Dimensions
2000 kg
7m
IMPORTANT
67.5°
60°
6m
50°
5m
40°
30°
20°
2m
10°
1300 kg
3m
2000 kg
2500 kg
3000 kg
4m
3700 kg
Due to continuous product improvements, machine specifications and/or equipment changes may be made without prior notification. This machine meets or exceeds AS1418.19-2007 as originally manufactured for intended applications. When utilising a suspended load, the JLG Load Management Indicator System (LMIS) must be installed in order to remain compliant with AS1418.19-2007.
0°
5m
4m
3m
2m
DO NOT exceed rated lift capacity loads, as unstable and dangerous machine
conditions will result.
DO NOT tip the machine forward to determine the allowable load.
1m
0m
Rated lift capacities shown are with machine equipped with standard carriage and pallet forks. When lifting loads, the machine requires a firm surface with undamaged, properly inflated tyres. Machine specifications and stability are based on rated lift capacities at specific boom angles and boom lengths. (If specifications are critical, the proposed application should be discussed with your dealer.)
1m
0m
600 mm
For more complete information on Cat products, dealer services, and industry solutions, visit us on the web at www.cat.com
© 2010 Caterpillar
All rights reserved.
CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow” and the POWER EDGE trade dress, as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
AEHQ6035-02 (03-2010)
Cat
®
TH414
Telehandler
Specifications
Engine
Hydraulic System
Model
Gross Power
Maximum Torque
Bore
Stroke
Displacement Cat C4.4 DITAAC
74.5 kW/101 hp
410 Nm/1400 rpm
105 mm
127 mm
4.4 litre
®
Weights
Maximum System Pressure Maximum Pump Flow Pump Type
Auxiliary Hydraulic Supply
Intermittent Continuous
Operating Weight with Carriage & Forks 9550 kg
Transmission Speeds
Operating Specifications
Forward
1
2
3
4
Reverse
1
2
3
Rated Load Capacity
On Tyres
On Stabilizers
Maximum Lift Height
Stabilizers Up
Stabilizers Down
Maximum Forward Reach
Top Travel Speed
Load at Max Height
Stabilizers Up
Stabilizers Down
Load at Max Reach
Stabilizers Up
Stabilizers Down
Outside Turning Radius Over Tyres
Outside Turning Radius Over Forks
Drawbar Pull 74.5 kW
3700 kg
3700 kg
13 700 mm
13 700 mm
9225 mm
32 km/h
1250 kg
2500 kg
350 kg
1000 kg
3805 mm
5640 mm
88,0 kN
Service Refill Capacities
Fuel Tank Hydraulic Tank 150 litre
90 litre
Tyres
Standard 15.5/80-24 16PR
Brakes
Service Brakes Parking Brakes
Servo assisted on front axle
Mechanical on front axle
250 bar
113 litre/min
Variable displacement
load sensing axial
piston pump
80 litre/min
60 litre/min
7 km/h
12 km/h
21 km/h
32 km/h
7 km/h
12 km/h
21 km/h
Boom Performance
Boom Up
Boom Down
Tele In
Tele Out
Crowd Forward (dump)
Crowd Backward
Combined
Up and Out
Down and In
Bucket Breakout Force to ISO 8313
Boom Breakout Force
13.0 Seconds
8.0 Seconds
11.0 Seconds
11.0 Seconds
3.0 Seconds
3.0 Seconds
23.0 Seconds
13.4 Seconds
65 kN
45 kN
Sound
Operator Sound
Exterior Sound (74.5 kW Engine)
78 dB(A)
106 dB(A)
TH414 Telehandler
Dimensions
All dimensions are approximate.
880 mm
2592 mm
1979 mm
458 mm
1225 mm
3200 mm
2036 mm
5091 mm
2449 mm
6325 mm
Load Chart and Dimensions
75°
60°
12 m
50°
40°
9m
3m
2m
10°
750 kg
20°
4m
350 kg
500 kg
5m
1000 kg
6m
1500 kg
7m
10 m
kg
8m
-1 m
30°
7m
6m
5m
20°
4m
3m
2m
1m
0m
40°
9m
kg
3000
30°
2500 kg
8m
kg
3700
10 m
50°
11 m
10°
3000 kg
2000
1500 kg
2000 kg
11 m
1000 kg
12 m
75°
60°
13 m
2500 kg
13 m
2500 kg
14 m
3700 kg
1250 kg
14 m
1m
0°
600 mm
9m 8m 7m 6m 5m 4m 3m 2m 1m 0m
0m
0°
-1 m
600 mm
9m 8m 7m 6m 5m 4m 3m 2m 1m 0m
Stabilizers Up
Stabilizers Down
IMPORTANT
Rated lift capacities shown are with machine
equipped with standard carriage and pallet forks.
When lifting a load, the machine requires a firm
surface with undamaged, properly inflated tyres.
Machine specifications and stability are based
on rated lift capacities at specific boom angles
and boom lengths. (If specifications are critical,
the proposed application should be discussed
with your dealer.)
DO NOT exceed rated lift capacity loads, as unstable
and dangerous machine conditions will result.
DO NOT tip the machine forward
to determine the allowable load.
Due to continuous product improvements,
machine specifications and/or equipment
changes may be made without prior notification.
For more complete information on Cat products, dealer services, and industry solutions, visit us on the web at
www.cat.com
© 2010 Caterpillar
All rights reserved.
CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow” and the POWER EDGE trade dress, as well as
corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
This machine meets or exceeds AS1418.19-2007
as originally manufactured for intended
applications. When utilising a suspended
load, the JLG Load Management Indicator
System (LMIS) must be installed in order
to remain compliant with AS1418.19-2007.
AEHQ6036 02(12-2010)
Cat
®
TH417
Telehandler
Specifications
Engine
Hydraulic System
Model
Gross Power
Maximum Torque
Bore
Stroke
Displacement Cat C4.4 DITAAC
74.5 kW/101 hp
410 Nm/1400 rpm
105 mm
127 mm
4.4 litre
®
Weights
Maximum System Pressure Maximum Pump Flow Pump Type
Auxiliary Hydraulic Supply
Intermittent Continuous
Operating Weight with Carriage & Forks 11 800 kg
Transmission Speeds
Operating Specifications
Forward
Rated Load Capacity
Maximum Lift Height
4000 kg
Stabilizers Up
Stabilizers Down
15 290 mm
17 300 mm
Maximum Forward Reach
Top Travel Speed
Load at Max Height
Stabilizers Up
Stabilizers Down
12 900 mm
32 km/h
500 kg
3000 kg
Load at Max Reach
Stabilizers Up
Stabilizers Down
0 kg
500 kg
Outside Turning Radius Over Tyres
Outside Turning Radius Over Forks
3920 mm
5650 mm
Service Refill Capacities
Fuel Tank Hydraulic Tank 150 litre
90 litre
Tyres
Standard 14.00-24 16PR TG02
Brakes
Service Brakes Parking Brakes
Servo assisted on front axle
Mechanical on front axle
1
2
3
4
250 bar
150 litre /min
Variable displacement load sensing axial piston pump
80 litre/min
60 litre/min
7 km/h
12 km/h
21 km/h
32 km/h
Reverse
1
2
3
7 km/h
12 km/h
21 km/h
Boom Performance
Boom Up
Boom Down
Tele In
Tele Out
Crowd Forward (dump)
Crowd Backward
Combined
Up and Out
Down and In
Drawbar Pull 74.5 kW
Bucket Breakout Force to ISO 8313
Boom Breakout Force
16.0 Seconds
13.0 Seconds
20.0 Seconds
25.0 Seconds
3.4 Seconds
3.0 Seconds
30.0 Seconds
23.0 Seconds
88,0 kN
65 kN
60 kN
Sound
Operator Sound
Exterior Sound (74.5 kW Engine)
78 dB(A)
106 dB(A)
TH417 Telehandler
Dimensions
All dimensions are approximate.
880 mm
2630 mm
2080 mm
401 mm
1275 mm
3200 mm
2078 mm
5135 mm
2440 mm
6670 mm
Load Chart and Dimensions
TH417
TH417TH417
14 m
14 m
13 m
13 m
13 m
12 m
12 m
12 m
11 m
11 m
10 m
10 m
9m
9m
14 m
50°
40°
11 m
10 m
30°
9m
8m
8m
8m
7m
7m
7m
20°
6m
6m
10°
2m
1000 kg
3m
500 kg
4m
250 kg
5m
2700 kg
20°
1500 kg
2000 kg
6m
3700 kg
4000 kg
1m
0m
0°
5m
5m
4m
10°4 m
3m
3m
2m
2m
1m
1m
0m
600 mm
-1 m
13 m 12 m 11 m 10 m 9 m 8 m 7 m 6 m 5 m 4 m 3 m 2 m 1 m 0 m
-1 m
0°
0m
50°
16 m
60°
15 m
50°
14 m
50°
13 m
40°
30°
40°
12 m
40°
11 m
10 m
30°
20°
10°
4000 kg
30°
9m
8m
20°
7m
1000 kg
15 m
17 m
6m
2700 kg
4000 kg
5m
4m
2m
1m
0°
0m
600 mm 600 mm
-1 m
10°
3m
13 m 12 m 11
13mm 10
12 m
m 11
9 mm 810mm 79 m
m 68 m
m 57mm 46mm 35 mm 24mm 13 mm 02 m
m 1m 0m
500 kg
15 m
60°
15 m
60°
18 m
2700 kg
16 m
1500 kg
2000 kg
16 m
3000 kg
16 m
72°
70°
1000 kg
17 m
500 kg 2000 kg
18 m
17 m
1000 kg
250 kg
18 m
17 m
500 kg
18 m
TH4
0°
-1 m
13 m 12 m 11 m 10 m 9 m 8 m 7 m 6 m
Stabilizers Down
Stabilizers Up
Stabilizers Up
Stabilizers
IMPORTANT
Rated lift capacities shown are with machine
equipped with carriage and pallet forks. The machine
must be level on a firm surface with undamaged,
properly inflated tyres. Machine specifications and
stability are based on rated lift capacities at specific
boom angles and boom lengths. (If specifications
are critical, the proposed application should be
discussed with your dealer.)
DO NOT exceed rated lift capacity loads, as unstable
and dangerous machine conditions will result.
DO NOT tip the machine forward to determine the
allowable load.
Due to continuous product improvements, machine
specifications and/or equipment changes may be
made without prior notification.
For more complete information on Cat products, dealer services, and industry solutions, visit us on the web at www.cat.com
© 2010 Caterpillar
All rights reserved.
Printed in U.S.A
Materials and specifications are subject to change without notice. Featured machines in photos may include additional equipment. See your Cat dealer for available options.
CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow” and the POWER EDGE trade dress, as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
This machine meets or exceeds AS1418.19-2007 as originally manufactured for intended applications. When utilising a suspended load, the JLG Load Management Indicator System (LMIS) must be installed in order to remain compliant with AS1418.19-2007.
AEHQ6148 (08-2010)
Cat
®
TH514
Telehandler
Specifications
Engine
Hydraulic System
Model
Gross Power
Maximum Torque
Bore
Stroke
Displacement Cat C4.4 DITAAC
74.5 kW/101 hp
410 Nm/1400 rpm
105 mm
127 mm
4.4 litre
®
Weights
Maximum System Pressure Maximum Pump Flow Pump Type
Auxiliary Hydraulic Supply
Intermittent Continuous
Operating Weight with Carriage & Forks 11 000 kg
Transmission Speeds
Operating Specifications
Forward
1
2
3
4
Reverse
1
2
3
Rated Load Capacity
On Tyres
On Stabilizers
Maximum Lift Height
Stabilizers Up
Stabilizers Down
Maximum Forward Reach
Top Travel Speed
Load at Max Height
Stabilizers Up
Stabilizers Down
Load at Max Reach
Stabilizers Up
Stabilizers Down
Outside Turning Radius Over Tyres
Outside Turning Radius Over Forks
Drawbar Pull 74.5 kW
4600 kg
5000 kg
13 380 mm
14 000 mm
9225 mm
32 km/h
1800 kg
2000 kg
500 kg
1200 kg
3920 mm
5570 mm
88,0 kN
Service Refill Capacities
Fuel Tank Hydraulic Tank 150 litre
90 litre
14.00-24 TG-02
Brakes
Service Brakes Parking Brakes
80 litre/min
60 litre/min
7 km/h
12 km/h
21 km/h
32 km/h
7 km/h
12 km/h
21 km/h
Boom Performance
Boom Up
Boom Down
Tele In
Tele Out
Crowd Forward (dump)
Crowd Backward
Combined
Up and Out
Down and In
Bucket Breakout Force to ISO 8313
Boom Breakout Force
17.0 Seconds
10.0 Seconds
20.0 Seconds
17.5 Seconds
4.0 Seconds
3.0 Seconds
28.0 Seconds
19.0 Seconds
95 kN
63 kN
Sound
Tyres
Standard 250 bar
150 litre/min
Variable displacement load sensing axial piston pump
Servo assisted on front axle
Mechanical on front axle
Operator Sound
Exterior Sound (74.5 kW Engine)
78 dB(A)
106 dB(A)
TH514 Telehandler
Dimensions
All dimensions are approximate.
880 mm
2630 mm
1979 mm
401 mm
3200 mm
2078 mm
5091 mm
2440 mm
6520 mm
Load Chart and Dimensions
70º
13 m
60º
12 m
50º
11 m
10 m
40º
9m
30º
7m
20º
3m
10º
2m
1m
0m
500 kg
4m
1000 kg
5m
1350 kg
6m
1800 kg
2500 kg
3450 kg
4300 kg
8m
15 m
14 m
14 m
13 m
13 m
12 m
12 m
11 m
11 m
10 m
10 m
9m
9m
8m
8m
30º
7m
7m
6m
5m
4600 kg
20º
10º
1m
0m
-1 m
11 m 10 m 9 m 8 m 7 m 6 m 5 m 4 m 3 m 2 m 1 m 0 m
600 mm
3m
2m
2m
0º
5m
4m
4m
3m
6m
1200 kg
14 m
15 m
0º
1m
0m
TH514
TH514
2000 kg
70º
60º
50º
75º
70º
60º
50º
40º
40º
30º
5000 kg
2000 kg
2600 kg
500 kg 3000 kg
4000 kg
1000 kg
1350 kg
TH514
15 m
20º
1800 kg
2500 kg
3450 kg
4300 kg
1225 mm
10º
4600 kg
0º
600 mm
-1 m
-1 m
11 m 10 m 9 m 8 m 117mm 106mm 9 5mm 8 4mm 7 3mm 6 2mm 5 1mm 4 0mm 3 m 2 m 1 m 0 m
Stabilizers Up
Stabilizers Down
600 mm
Stabilizers Up
IMPORTANT
Rated lift capacities shown are with machine
equipped with standard carriage and pallet forks.
When lifting a load, the machine requires a firm
surface with undamaged, properly inflated tyres.
Machine specifications and stability are based on rated lift capacities at specific boom angles and boom lengths. (If specifications are critical, the proposed application should be discussed with your dealer.)
DO NOT exceed rated lift capacity loads, as unstable
and dangerous machine conditions will result.
DO NOT tip the machine forward to determine the allowable load.
Due to continuous product improvements, machine specifications and/or equipment changes may be made without prior notification.
This machine meets or exceeds AS1418.19-2007 as originally manufactured for intended applications. When utilising a suspended load, the JLG Load Management Indicator System (LMIS) must be installed in order to remain compliant with AS1418.19-2007.
For more complete information on Cat products, dealer services, and industry solutions, visit us on the web at www.cat.com
© 2010 Caterpillar
All rights reserved.
Printed in U.S.A
Materials and specifications are subject to change without notice. Featured machines in photos may include additional equipment. See your Cat dealer for available options.
CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow” and the POWER EDGE trade dress, as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
AEHQ6083-01 (08-2010)