catalog-09-09-09 - complete.qxp

Transcription

TABLE OF CONTENTS
ADAPTERS
Oil Filter By-Pass Adapter . . . . . . 27
Flywheel . . . . . . . . . . . . . . . . . . 30
V-Drive. . . . . . . . . . . . . . . . . . . . 33
Steering Wheels . . . . . . . . . . . . 60
ALTERNATORS BRACKETS. . . . . . . 78
BATTERY BOXES . . . . . . . . . . . . . . 78
BEARINGS
Flange . . . . . . . . . . . . . . . . . . . 37
Steering . . . . . . . . . . . . . . . . . . 59
Strut . . . . . . . . . . . . . . . . . . . . . 41
BOAT BUILDING BOOKS
(Glen-L). . . . . . . . . . . . . . . . . . . 79
BOW EYES . . . . . . . . . .. . . . . . . . . 72
CABLES
Shift . . . . . . . . . . . . . . . . . . . . . 56
Steering . . . . . . . . . . . . . . . . 59-60
Tach . . . . . . . . . . . . . . . . . . . . . .74
Throttle . . . . . . . . . . . . . . . . . . . 56
CARBURETOR
Flame Arrester . . . . . . . . . . . . . . 25
Throttle Bracket . . . . . . . . . . . . . 54
Tilt Shim . . . . . . . . . . . . . . . . . . 26
CAVITATION PLATE
Bosses . . . . . . . . . . . . . . . . . . . 63
Cavitation Plate Kit . . . . . . . . . . . 61
Clevis . . . . . . . . . . . . . .. . . . . . . 63
Control Arm . . . . . . . . . . . . . . . .66
Control Handle . . . . . . . . . . . . . 65
Control Shaft . . . . . . . . . . . . . . . 61
Foot Control . . . . . . . . . . . . . . . 67
Override Assembly . . . . . . . . . . . 67
Pillow Blocks . . . . . . . . . . . . . . . 66
Pins, Clips and Rings. . . . . . . . . . 64
Plate Kits . . . . . . . . . .. . . . . . . . 62
Plate Stock . . . . . . . . . . . . . . . . . 65
Thru-Hulls . . . . . . . . . . . . . . . . . 65
Turnbuckles . . . . . . . . . . . . . . . . 63
Water Pick-Ups . . . . . . . . . . . . . . 68
CLAMPS
Hose . . . . . .. . . . . . . . . . . . . . . 69
Steering . . . . . . . . . . . . . . . . . . 59
COLLARS
Split Safety. .. . . . . . . . . . . . . . . 42
Stainless Steel . . . . . . . . . . . . . . 42
Strut Collar . . . . . . . . . . . . . . . . 42
CONTROLS
Foot Throttle . . . . . . . . . . . . . . . 54
Hand Shift/Throttle . . . . . . . . . . . 55
COUPLERS
Chain . . . . . . . . . . . . . . . . . . . . 31
Split Sleeve . . . . . . . . . . . . . . . . 42
V-Drive . . . . . . . . . . . . . . . . . . . 29
COVERS
Timing Gear . . . . . . . . . . . . . . . .18
Water Plates . . . . . . . . . . . . 19-20
DECK HARDWARE . . . . . . . . . . . . 71
DIVIDERS (Water)
Split Tee . . . . . . . . . . . . . . . . . . 24
Water Discharge . . . . . . . . . . . . 21
DRAINS
Bilge . . . . . . . . . . . . . . . . . . . . . 70
Oil . . . . . . . . . . . . . . . . . . . . . . 28
DRIVE DAMPERS
Borg Warner . . . . . . . . . . . . . . . 17
EXHAUST SYSTEM
Elbows/Adapters . . . . . . . . . . . . . 7
Hose (flexible) . . . . . . . . . . . .10, 72
Manifolds (Log Type). . . . . . . . . . 3-4
Manifolds (I/O) . . . . . . . . . . . . . . 2
Manifolds (Rectangular) . . . . . . . . 5
Over-Transom Pipes . . . . . . . . . . . 8
Ports . . . . . . . . . . . . . . . . . . . 9-10
Risers . . . . . . . . . . . . . . . . . . . . . .6
FASTENERS
Nuts and Bolts . . . . . . . . . . . . . . 77
Stringer Washers . . . . . . . . . . . . 77
FINS . . . . . . . . . . . . . . . . . . . . . . 53
FLAME ARRESTERS . . . . . . . . . . . 25
FLYWHEEL POWER TAKE-OFF . . . . 30
FUEL
Gauges . . . . . . . . . . . . . . . . . . . 75
Fills . . . . . . . . . . . . . . . . . . . . . 11
Filters . . . . . . . . . . . . . . . . . . . 11
Vents . . . . . . . . . . . . . . . . . . . . 11
GASKETS . . . . . . . . . . . . . . . . . 7, 34
GAUGES . . . . . . . . .. . . . . . . . . 74-75
Bezels . . . . . . . . . . . . . . . . . . . . . 7 3
Block Temperature . . . . . . . . . . 75
Deck Mounts . . . . . . . . . . . . . . . 73
Senders . . . . . .. . . . . . . . . . . . . 75
HOSE
Borg Warner . . . . . . . . . . . . . . . .17
Clamps . . . . . . . . . . . . . . . . . . . 69
Fittings . . . . . . . . . . . . . . . . . 68-69
Exhaust . . . . . . . . . . . . . . . . . 10,69
Oil . . . . . . . . . . . . . . . . . . . . 17, 28
Shaft Log . . . . . . . . . . . . . . . . . . 35
Water . . . . . . . . . . . . . . . . . . . . 68
MOTOR MOUNTS . . . . . . . . . . .12-17
MUFFLERS . . . . . . . . . . . . . . . . . . 8
OIL
Brackets . . . . . . . . . . . . . . . . . . . 28
By-Pass Adapters . . . . . . . . . . . . 27
Coolers . . . . . . . . . . . . . . . . . . . 28
Drain . . . . . . . . . . . . . . . . . . . . 28
Filters . . . . . . .. . . . . . . . . . . . . . 28
PIPE-TO-HOSE FITTINGS . . . . . . . 69
PLATES
Block-Off (Water) . . . . . . . . . . 19-20
Cavitation . . . . . . . . . . . . . . . . 62
POWER TAKE-OFF
Crankshaft . . . . . . . . . . . . . . . . . 29
Flywheel . . . . . . . . . . . . . . . . . . 30
V-Drive . . . . . . . . . . .. . . . . . . . 29
PROPELLERS AND SHAFTING
Keys . . . . . . . . . . . . . . . . . . . . . 42
Nuts . . . . . . . . . . . . . . . . . . . . . 42
Pullers . . . . . . . . . . . . . . . . . . . . 45
Propellers . . . . . . . . . . . . . . 44-45
Shafts . . . . . . . . . . . . . . . . . . . . 43
PULLEYS (Steering) . . . . . . . . . . . . 57
PUMPS
Bilge . . . . . . . . . . . . . . . . . . . . . 23
Engine (Water). . . . . . . . . . . . 22-23
Water Pump Impellers . . . . . . 22-23
RUDDERS . . .. . . . . . . . . . . . . 49-51
GLENWOOD MARINE
-1-
Post Brackets . . . . . . . . . . . . . . . 48
Quadrants . . . . . . . . . . . . . . . . 48
Safety Collars . . . . . . . . . . . . . . . 42
Split Safety Collars . . . . . . . . . . . 42
Stuffing Boxes . . . . . . . . . . . . 46-47
Tiller Arm . . . . . . . . . . . . . . . . . 48
Transom Brackets . . . . . . . . . . . . 52
SHAFT LOG
Shaft Logs . . . . . . . . . . . . . . . . 35
Shaft Logs - Cruisers . . . . . . . . . . 36
Clamps and Hose. . . . . . . . . . . . 35
Stuffing Boxes . . . . . . . . . . . . 35,37
SKI TOWS . . . . . . . . . . . . . . . . 71-72
STEERING
Cable Steering Parts . . . . . . . 58-59
Pulleys . . . . . . . . . . . . . . . . . . . 57
Steering Shafts . . . . . . . . . . . . . 59
Wheels . . . . . . . . . . . . . . . . . . . 60
STRUTS . . . . . . . . . . . . . . . . . . 38-40
Bearings . . . . . . . . . . . . . . . . . . 41
Strut Collar . . . . . . . . . . . . . . . . 42
STUFFING BOXES
Plates . . . . . . . . . . . . . . . . . . . . 46
Rudder . . . . . . . . . . . . . . . . .46-47
Shaft Log . . . . . .. . . . . . . . . . 35,37
SWITCHES . . . . .. . . . . . . . . . . . . . 76
TACHOMETERS
Cables . . . . . . . . . . . . . . . . . . . 74
Deck Mount . . . . . . . . . . . . . . . . 73
Electrical . . . . . . . . . . . . . . . . . . 74
Mechanical . . . . . . . . . . . . . . . . 74
THROTTLES
Brackets . . . . . . . . . . . . . . . . . . .54
Foot Control . . . . . . . . . . . . . . . 54
Hand Control . . .. . . . . . . . . . . . 5 5
THRU-HULL
Cavitation Plate . . .. . . . . . . . . . .65
Water . . . . . . . . . . . . . . . . . . . . 69
THRUST BEARINGS/CAGES. . . . . . 37
TILLER ARM . . . . . . . . . . . . . . . . . 48
TILT SHIMS . . . . . . . . . . . . . . . . . 26
TIMING GEAR COVERS . . . . . . . . 18
TORQUE TUBE . . . . . . . . . . . . . . . 31
Guards . . . . . . . . . . . . . . . . . . . 32
TURNBUCKLES . . . . . . . . . . . . . . . 63
V-DRIVES
Casale . . . . . . . . . . . . . . . . . . . .34
Shifter . . . . . . . . . . . . . . . . . . . . 34
Take-Off . . . .. . . . . . . . . . . . . . . 29
Gasket Set (Split Case Only) . . . . 34
VENTS
Gas . . . . . . . . . . . . . . . . . . . . . . 11
Cowl . . . . . . . . . . . . . . . . . . . . . 74
WATER
Divider . . . . . . . . . . . . . . . 21, 24
Hose . . . . .. . . . . . . . . . . . . . . . 68
Pick-Up . . . . . . . . . . . . . . . . 24, 68
Pump Cover Plates . . . . . . . . . . . 19
Water Plates. . . . . . . . . . . . . .20-21
Pumps and Impellers . . . . . . . 22-23
(323) 757-3141
EXHAUST SYSTEMS
MAGNAFLOW® SERIES STERN DRIVE EXHAUST SYSTEM
Glenwood’s Magnaflow® Series Stern Drive Exhaust System is a lightweight and
affordable replacement for stock cast-iron MerCruiser, OMC and Volvo I/O manifolds
and risers. The Magnaflow® Series features weight saving precision cast aluminum
exhaust manifolds and risers which are a direct bolt-on, no modification installation.
To help insure maximum durability and corrosion resistance, Magnaflow® Exhaust
Systems are hard anodized inside and out to a battle ship gray finish and are also
available polished. Magnaflow® Exhaust Systems are available for both small block
(305 and 350 c.i.) and big block (454 c.i.) Chevrolet V-8 engines.
Catalog No.
Item No.
Magnaflow®
Magnaflow®
Magnaflow®
Magnaflow®
(exhaust manifolds only) small block V-8
(exhaust manifolds only) small block V-8
(exhaust manifolds only) big block V-8
(exhaust manifolds only) big block V-8
(Hard anodized)
(Polished
(Hard anodized)
(Polished)
35010
35020
45410
45420
1610
1611
1620
1621
MAGNAFLOW® RISER/ELBOW
The Magnaflow® exhaust riser/elbow is cast
aluminum and fully water jacketed. Risers are
hard anodized inside and out to a battle ship
gray finish and are also available polished.
Will fit both big block and small block Magnaflow®
exhaust manifolds. A direct replacement for
MerCruiser, OMC, and Volvo I/O cast-iron
riser/elbow. Accommodates standard MerCruiser
shift/throttle bracket attachment. Full 4” O.D. riser.
Catalog No.
29170
33472
Magnaflow® riser/elbow (Hard anodized)
Magnaflow® riser/elbow (Polished)
GLENWOOD MARINE
-2-
Item No.
1630
1631
(323) 757-3141
EXHAUST MANIFOLDS
CHEVROLET - SMALL BLOCK V-8
265-283-305-307-327-350 & 400 cu. in.
Free flowing, swept back design for
maximum performance.
Catalog No.
28320
Item No.
697
CHEVROLET - BIG BLOCK V-8
396-427 & 454 cu. in.
Cast 356 aluminum alloy.
Features smooth flowing
exhaust ports for maximum
efficiency.
Catalog No.
39620
Item No.
956
CHEVROLET - V-6
262 cu. in., 4.3 liter
A true performance fully water
jacketed header type manifold.
Use with 4” elbows or risers.
Catalog No.
23920
Item No.
1298
Out from head - 4-1/2”
GLENWOOD MARINE
-3-
(323) 757-3141
EXHAUST MANIFOLDS
FORD V-8
352-390-406-427 & early 428 cu. in.
All Glenwood header type manifolds
have large 3” exhaust outlets for
extra performance.
Catalog No.
42720
Item No.
959
FORD AND LINCOLN
429 - 460
Space saving header manifold design
with brightly polished aluminum finish.
Catalog No.
42920
Item No.
960
CHRYSLER WEDGE
383-413-426 & 440cu.in
Wedge 1959-1973 on B Block
engines. Will not fit a Hemi engine.
Catalog No.
44020
Item No.
961
OLDSMOBILE V-8
350-400-403-425 & 455 cu. in.
Every Glenwood header manifold is fully
water jacketed to minimize heat build-up.
Catalog No.
45520
Item No.
962
GLENWOOD MARINE
-4-
(323) 757-3141
EXHAUST MANIFOLDS
PONTIAC
389, 421 & 455 cu. in.
1959-1979 (except Ram Air)
Includes elbow adapters.
Catalog No.
29321
Item No.
720
FORD
221-260-289-302 & 351 cu. in.
(except Cleveland engine)
Distinctive finned exterior. Lightweight
cast aluminum construction. Includes
elbow adapters.
Catalog No.
31120
Item No.
755
CHEVROLET V-8
265-283-307-327-350 & 400 cu. in.
Lightweight and durable cast 356
aluminum alloy. Finned exterior. Has
full water jacketed cooling. Includes
elbow adapters.
Catalog No.
31620
Item No.
758
GLENWOOD MARINE
-5-
(323) 757-3141
RISERS - CAST ALUMINUM
WATER COOLED RISERS
Designed exclusively for Glenwood’s high performance
marine header manifolds. These water jacketed risers have
a full 3” exhaust outlet.
Flange
Size
4-7/8”
Hole
Size
3”
Hose
Size
Catalog
No.
2-7/8”or
3½” I.D.
29162
Item
No.
714
WATER COOLED RISERS
Thru-transom exhaust outlets on low freeboard hulls may
allow water to enter the engine. To prevent possible damage to valve chambers and other internal parts, exhaust risers are a must. (Fits header type manifolds only).
Flange
Size
Hole
Size
Hose
Size
Catalog
No.
Item
No.
4-7/8”
3”
2-7/8” or
3½” I.D.
29142
710
WATER COOLED SMALL RISERS
For Glenwood’s rectangular custom exhaust manifolds,
these cast aluminum risers feature complete water cooling.
Flange
Size
4”
Hole
Size
2½”
Hose
Size
2- 7/8”I.D.
Catalog
No.
Item
No.
29182
716
Same riser as above but with large flange for header type manifolds.
Flange
Hole
Hose
Catalog
Item
Size
Size
Size
No.
No.
4-7/8”
2½”
2-7/8”I.D.
29172
715
WATER COOLED SMALL RISERS
‘DOWN-ANGLE OUTLET’
Made for Glenwood’s rectangular and V-6 Chevrolet manifolds for typical I/O installation.
Flange
Hole
Hose
Catalog
Item
Size
Size
Size
No.
No.
2-7/8”I.D.
29192
717
4”
2½”
NOTE: ALL RISERS COME UNDRILLED
GLENWOOD MARINE
-6-
(323) 757-3141
EXHAUST ELBOWS
STRAIGHT WATER
COOLED OUTLET
35º WATER
COOLED
ELBOWS
The traditional Glenwood
rectangular custom exhaust
manifolds utilize these cast aluminum
elbows. All use 2-7/8” flexible hose to connect elbows to exhaust flanges.
Flange
Size
Hole
Size
Hose
Size
Catalog
No.
Item
No.
4”
2½”
2-7/8”
29112
707
Ideal for conventional inboard engine direct
applications (tournament type ski boats).
Flange
Size
4-7/8”
Hole
Size
80º WATER
COOLED
ELBOWS
Hole
Size
4”
2½”
Hose
Size
Catalog
No.
2-3/8 ”or 29122
2-7/8” I.D.
Item
No.
708
4-7/8”
3”
29130
Item
No.
1600
Rectangular type exhaust manifolds must
use these adapters when running water
cooled exhaust elbows. Furnished with studs,
nuts and gaskets.
Catalog
No.
29021
29022
29023
Item
No.
703
704
705
GASKETS ONLY
Description
All Glenwood marine header manifolds use
these large capacity water cooled elbows.
Designed for 2½” or 3” pipe size. (Fits
header type manifolds only).
Hole
Size
3½” I.D.
Flange
Use With
Size
Item No.
3½” x 3¾”
755 & 758
3-5/16 x 4½”
694
3-9/16” x 4½”
720
35º EXTRA
LARGE
WATER
COOLED
ELBOWS
Flange
Size
2-7/8”or
Catalog
No.
ELBOW ADAPTERS
For engine installations
close to the transom, (jets and
stern drives) these elbows will
accommodate 2” or 2½” pipe size. (Fits
rectangular type exhaust manifolds only).
Flange
Size
3”
Hose
Size
Hose
Size
2-7/8”or
3½” I.D.
Catalog
No.
29132
GLENWOOD MARINE
Item
No.
709
Square Gasket
Three Hole Gasket
Four Hole Gasket
Catalog No.
28999
29099
29199
Item No.
702
706
718
NOTE: ALL ELBOWS COME
UNDRILLED
-7-
(323) 757-3141
O.T. TRANSOM EXHAUST • GLASS PACK MUFFLERS
OVER TRANSOM EXHAUST
CAST ALUMINUM
Available in two length sizes, these highly polished cast aluminum Over-Transom
Exhaust pipes feature 3” outlets for maximum engine efficiency. (Fits header type
exhaust manifolds only - will not fit a jet boat).
Lengths
Catalog No.
Item No.
Pair 29”
29159
713
Pair 31”
29151
711
Pair 29” 31”
29152
712
GLASS PACK MUFFLERS
Easy to install. Used with steel
Over-Transom Exhaust Pipes.
Catalog No.
FOR STEEL O.T.’S ONLY
GLENWOOD MARINE
606241
-8-
Item No.
1124
(323) 757-3141
EXHAUST PORTS • GARDS
EXHAUST PORTS
Glenwood’s Aluminum Thru-transom
exhaust ports are available in three
sizes. They are epoxy powder coated
black for maximum durability and are
made to use Salisbury Exhaust Gards.
Pipe I.D.
2½”
3”
3½”
Pipe O.D. Catalog No. Item No.
30925
1810
2-7/8”
3½”
30935
1820
4”
30940
1830
SALISBURY EXHAUST GARDS
Exhaust Pipe Size:
2-½” to 3”
Salisbury Exhaust Gards are the most
widely used method of preventing engine
backwash. Salisbury Exhaust Gards are
made from durable, non-corrosive neoprene rubber. Furnished with a stainless
steel adjustable clamp to secure the gard
to the exhaust tip.
Catalog No. Item No.
EG-300
1400
NOTE: THE MANUFACTURER OF THE SALISBURY GARDS HAS DISCONTINUED THEIR
MARINE LINE. THE ABOVE GARDS ARE ALL WE
HAVE IN STOCK.
TRUMPET TYPE EXHAUST PORT
The popular Trumpet Exhaust Port keeps the
transom clean and attractive. Furnished with
studs, nuts and washers for easy installation.
Description
Pipe
I.D.
Polished Alum. 2½”
Polished Alum. 3”
Chrome Brass 2½”
Chrome Brass
3”
Pipe Catalog
O.D.
No.
2-7/8”
3½”
2-7/8”
3½”
21322
21323
21342
21343
Item
No.
488
489
490
491
SEE NEXT PAGE FOR EXHAUST HOSE
GLENWOOD MARINE
-9-
(323) 757-3141
EXHAUST PORTS • EXHAUST HOSE
CUSTOM EXHAUST PORT
Glenwood’s Custom Exhaust Port is available in
polished aluminum or chrome brass. Furnished
with studs, nuts and washers.
Description
Pipe
I.D.
Polished Alum. 2”
Polished Alum. 2½”
Polished Alum. 3”
Chrome Brass
2”
Chrome Brass 2½”
Chrome Brass
3”
Pipe
O.D.
Catalog
No.
Item
No.
2-3/8”
2-7/8”
3½”
2-3/8”
2-7/8”
3½”
30622
30625
30623
30642
30645
30643
743
745
744
746
748
747
FLAPPER TRUMPET EXHAUST PORT
This exhaust port features a built-in flapper to
prevent water from entering the engine on the
low freeboard and deep-vee hulls. Available in
polished aluminum, chrome brass and stainless
steel. Furnished with studs, nuts and washers.
Description
Pipe
I.D.
Pipe
O.D.
Catalog
No.
Polished Alum.
Polished Alum.
Polished Alum.
Chrome Brass
Chrome Brass
Chrome Brass
Stainless Steel
Stainless Steel
2½”
3”
3½”
2½”
3”
3½”
2½”
3”
2-7/8”
3½”
4”
2-7/8”
3½”
4”
2-7/8”
3½”
30825
30823
30824
30845
30843
30844
30865
30863
Item
No.
750
749
1601
752
751
1602
1293
1294
EXHAUST HOSE
CORRUGATED WITH WIRE
REPLACEMENT FLAPS
Catalog No.
Item No.
30800
753
Center to Center Hole Spread is 1-1/8”
Specify size when ordering
Small - 3-3/8”
Large - 4-3/16”
For Aluminum and Chrome Brass Ports OnlyFor
S.S. Replacement Flaps - please call.
GLENWOOD MARINE
Pipe O.D.
Hose I.D.
2-7/8”
3-1/2””
4”
2-7/8”
3-1/2”
4”
Catalog No.
21927
21935
21940
Item No.
520
521
522
NOTE: EXHAUST HOSE CUT TO SIZE IS NOT
RETURNABLE.
-10-
(323) 757-3141
GAS FILLS • FILTERS
GAS VENT
FLIP-TOP GAS FILL
STAINLESS STEEL
CAST BRASS
A two piece gas fill,
made of cast brass and
chrome plated. Made
for 2” hose.
This gas vent is machined from stainless
steel and highly polished. Designed to
receive 3/8” I.D. hose. Thread length: 1”
Catalog No.
19650
Item No.
405
CAST BRASS
A full 3/8” hole thru
this fitting, provides
venting for tanks.
Chrome plated brass.
Aluminum
Stainless
Pipe Length: 1-5/8”
Item No.
407
Chrome plated flush
mount deck plate, available
in three sizes with a hose
connection.
Catalog No.
25544
25545
25542
GLENWOOD MARINE
Catalog No.
Item No.
25825
25865
677
1296
This marine gasoline
filter can be installed
between fuel pump
and carburetor or
at tank.
CAST BRASS
Flange O.D.
3”
3½”
4”
Item No.
652
653
GASOLINE FILTERS
PIPE DECK PLATE
Pipe I.D.
1¼”
1½”
2”
Catalog No.
255200
255250
FLIP-TOP GAS FILL
Type
Pipe I.D.: 3/8”
19740
Flange O.D.
3-3/8”
3 ¾”
This flip top gas
fill is designed to
be connected to
the tank with 2”
I.D. hose. The
cap has a quick
release spring
and a leak proof
filler.
GAS VENT
Catalog No.
Throat I.D.
2”
2½”
Item No.
650
651
649
Description
Catalog No.
Complete
Extra Filter
12601
12609
-11-
Item No.
65
66
(323) 757-3141
MOTOR MOUNTS
FORD COVER AND MOUNT
FORD FLYWHEEL COVER
CAST ALUMINUM
CAST ALUMINUM
Ford 352-390-406-427 & 428 cu. in.
Ford 352-390-406-427 & 428 cu. in.
Made to receive starters 1964 or later
Engineered for maximum strength.
Features heat treated extruded
aluminum alloy. All bolts and aluminum
angle for installation are included.
Adjustable stringer spacing from 22”
to 28”.
Cover with Pump
Drive
One piece rear mounts bolt directly to
the engine and are machined to receive
the starter. Adjustable stringer spacing
from 22” to 28”.
35202
891
CHRYSLER COVER AND MOUNT
Catalog No
Item No.
35302
908
CHRYSLER FLYWHEEL COVER
CAST ALUMINUM
CAST ALUMINUM
361-363-383-413-426 & 440 cu. in.
361-383-413-426 & 440 cu. in.
B engines 1959 and later
Designed for simple installation.
Furnished with extruded aluminum
angle to bolt through stringers.
to 28”.
Motor mounts are furnished with extruded
aluminum angle to bolt through stringers.
Adjustable stringer spacing from 22” to
28”.
Catalog No.
Item No.
Cover with pump drive
for single bolt cam
35203
892
With gear
reduction starter
Cover with pump drive
for three bolt cam
35233
901
NOTE: ALL MOUNTS ARE FOR A FOUR
POINT APPLICATION.
GLENWOOD MARINE
-12-
35303
909
(323) 757-3141
MOTOR MOUNTS
PONTIAC COVER AND MOUNT
BUICK COVER AND MOUNT
CAST ALUMINUM
Pontiac 1965-1979
CAST ALUMINUM
Buick 1953-1965
Lightweight design, made from durable
356 T-6 aluminum alloy. Easy installation. All bolts, aluminum angle and pump
drive are included. Adjustable stringer
spacing from 22” to 28”.
Engineered for maximum strength. With
heat treated extruded aluminum alloy.
All bolts and aluminum angle for installation are included. Adjustable stringer
Catalog No.
35204
Item No.
Cover with Pump
Drive
893
CHEVROLET COVER AND MOUNT
CAST ALUMINUM
Chevrolet 396 - 427 & 454 cu. in.
Designed to handle the horsepower and
torque loads of the big block Chevrolet
engine. All bolts, aluminum angle and
pump drive are included. Adjustable
stringer spacing from 22” to 28”.
Catalog No.
35205
Item No.
894
NOTE: ALL MOUNTS ARE FOR A FOUR
POINT APPLICATION.
GLENWOOD MARINE
Catalog No.
35200
Item No.
890
CHEVROLET FLYWHEEL COVER
CAST ALUMINUM
Chevrolet V-6 - 327 - 350 - & 400 cu. in.
(1964-2002); 396 - 427 - 454 & 502 cu. in.
One piece flywheel covers bolt directly
to the engine. Machined to receive
starter. Easy installation. All bolts and
aluminum angle are included.
to 28”.
Catalog No.
Item No.
35305
911
-13-
(323) 757-3141
MOTOR MOUNTS
CHEVROLET FRONT MOUNT
CHEVROLET FLYWHEEL COVER
CAST ALUMINUM
Chevrolet 396 - 427 & 454 cu. in.
CAST ALUMINUM
Chevrolet 396 - 427 & 454 cu. in.
The most advanced design in engine
mounts. Features full adjustment.
Engine mounts on rubber shock pads.
Reduces vibration and noise. Adjustable
Catalog No.
Item No.
35206
895
A companion mount to Glenwood’s
#895 rubber front motor mount. These
mounts are fully adjustable and install
easily in a variety of deep vee hulls.
to 26”.
Catalog No.
35306
Item No.
912
OLDSMOBILE FRONT MOUNT
OLDSMOBILE FLYWHEEL COVER
CAST ALUMINUM
Oldsmobile 425 & 455 cu. in.
CAST ALUMINUM
Adjustable rubber front mount reduces
vibration, and lowers noise levels.
to 26”.
Catalog No.
35207
One piece flywheel cover with fully
adjustable rubber mounts. These
mounts are easily installed. Adjustable
Catalog No.
Item No.
35307
896
Item No.
913
NOTE: ALL MOUNTS ARE FOR A FOUR POINT APPLICATION.
GLENWOOD MARINE
-14-
(323) 757-3141
MOTOR MOUNTS
CHEVROLET FRONT MOUNT
CHEVROLET REAR MOUNT
CAST ALUMINUM
Chevrolet V-6-283-327 & 350 cu. in.
Chevrolet 396-427-454 & 502 cu. in.
Catalog No.
Item No.
CAST ALUMINUM
Chevrolet V-6-283-327 & 350 cu. in.
Chevrolet 396-427-454 & 502 cu. in.
(1964-2002)
Bolts directly to engine, machined to
receive starter. Engine stringer spacing
from 22” to 26”.
35209
35210
1292
897
Catalog No.
Item No.
35310
914
These mounts will adapt to engine
Small Block
Big Block
OLDSMOBILE FRONT MOUNT
OLDSMOBILE REAR MOUNT
CAST ALUMINUM
CAST ALUMINUM
Highly polished aluminum finish.
Durable lightweight construction. Engine
Catalog No.
Item No.
35211
898
Bolts directly to engine. Machined to
receive starter. Engine stringer spacing
from 22” to 26”.
Catalog No.
Item No.
35311
915
GLENWOOD MARINE
-15-
(323) 757-3141
MOTOR MOUNTS
FORD FRONT MOUNT
FORD REAR MOUNT
CAST ALUMINUM
Ford 429-460 cu. in.
CAST ALUMINUM
Ford 429-460 cu. in.
Perfect mount for big block Ford V-8.
Engine will adapt to stringer spacing
from 22” to 26”.
Catalog No.
Item No.
35214
900
Highly polished aluminum finish. Bolts
directly to engine. Precision machined
to receive starter motor. Stringer
Polished
Catalog No.
Item No.
32400
32401
1640
1641
Item No.
35314
917
BORG WARNER/CHEVROLET
REAR MOUNT STANDARD
BORG WARNER/CHEVROLET
REAR MOUNT WITH
TOP MOUNT
STARTER
Designed for
boats equipped
with Borg Warner
Velvet drive transmissions. Features
‘top-mount’ starter
placement for easy
access and corrosion protection. Uses
Delco Starter #1109485.
Catalog No.
Standard rear
mount for Borg
Warner Velvet
drive transmissions. Cast
aluminum.
Catalog No.
Polished
32424
32425
Item No.
781
784
GLENWOOD MARINE
-16-
(323) 757-3141
MOUNTS • DAMPERS • HOSE
BORG WARNER
FORD REAR MOUNT
Ford 429 - 460
Fits Borg Warner transmissions. Use either a small
or large flywheel, but must have stock plate that fits
between engine and transmission.
Catalog No.
Item No.
32414
782
BORG WARNER
OIL COOLER HOSES
Fits Borg Warner transmissions.
Hoses are 15” and 18” and are
sold in pairs.
Catalog No.
Item No.
32420
788
BORG WARNER
DRIVE DAMPER
For use with Borg Warner 71 and 72
transmissions. Made to go onto the
clutch flywheel.
Catalog No.
Item No.
32406
GLENWOOD MARINE
779
-17
(323) 757-3141
TIMING GEAR COVERS
CHEVROLET
TIMING
GEAR COVER
CHEVROLET
TIMING
GEAR COVER
Chevrolet 265-283327-350* & 400* cu in.
Chevrolet 396 427 & 454 cu in.
Includes bolts and water
pump cam drive. Please
specify cam drive needed (see below)
Catalog No.
Item No.
34720
875
*350 and 400 with small Harmonic
Balancers - These will only fit a 7” diamater or below harmonic balancer.
Mark IV aluminum
10 bolt cover for big
block Chevrolet engines.
Includes bolts, water pump cam drive and
gasket.
Catalog No.
Item No.
36920
935
Mark IV
CHEVROLET
TIMING
GEAR COVER
CHEVROLET
TIMING
GEAR COVER
Chevrolet 454 cu. in.
Chevrolet 454 502 cu. in.
Mark V Aluminum
block Chevrolet engines. Includes bolts,
water pump cam drive and gasket.
Please specify cam drive needed
(see below)
Mark VI Aluminum
block Chevrolet engines. Includes bolts,
water pump cam drive and gasket.
Please specify cam drive needed (see
below)
Mark V
Mark VI
Catalog No.
Item No.
36985
936
Catalog No.
Item No.
36986
937
Regular Chevy Cam Drive Specs
Roller Chevy Cam Drive Specs
Bolt Circle:
Hole Spread:
Bolt Circle:
Hole Spread:
1.306
1.178” or 1-3/16”
GLENWOOD MARINE
-18-
1.160
1.004” or 1”
(323) 757-3141
PUMP COVER PLATES
OLDSMOBILE 425 & 455
PUMP COVER PLATE
CAST ALUMINUM
Polished water pump cover plate. Ideal
for jet installations. Furnished with
bolts.
Catalog No.
27620
Item No.
691
FORD 429 & 460
PUMP COVER PLATE
CAST ALUMINUM
Polished water pump cover plate. Ideal
for jet installations. Furnished with
bolts.
Catalog No.
27820
Item No.
693
OLDSMOBILE 425 & 455
CAM DRIVEN WATER PUMP
COVER PLATE
CAST ALUMINUM
Pump cover plate is made to use with
stock steel timing chain cover. Furnished
with cam drive and bolts.
Catalog No.
Item No.
27685
1665
FORD 429 & 460 CAM DRIVEN
WATER PUMP COVER PLATE
CAST ALUMINUM
Pump cover plate is made to use with
stock aluminum timing chain cover.
Furnished with cam drive and bolts.
Catalog No.
27885
Item No.
1675
GLENWOOD MARINE
-19-
(323) 757-3141
COVER PLATES
WATER COVER PLATES
CAST ALUMINUM AND POLISHED
SOLD BY THE PAIR
CHEVROLET
265, 283, 327
and 350
Catalog No.
27220
Item No.
688
CHEVROLET
396, 427 and 454
Catalog No.
27720
Item No.
692
FORD
390, 406 and 427
Catalog No.
27320
Item No.
689
PONTIAC
389 and 421
Catalog No.
27420
Item No.
690
GLENWOOD MARINE
-20-
(323) 757-3141
WATER DIVIDERS • THERMOSTAT KIT
THERMOSTAT COVER PLATES
CAST ALUMINUM
To block off thermostat opening in the intake manifold. Polished finish.
CHEVROLET
Catalog No.
27027
FORD - 429-460
Item No.
1263
Catalog No.
27026
Item No.
686
WATER DISCHARGE DIVIDERS
WATER DISCHARGE DIVIDERS
CAST ALUMINUM
CAST ALUMINUM
Ford 332-352-390-406-427 & 428 cu. in.
Polished aluminum alloy. Provides for
equal discharge of water and easy
connection of water hoses.
Catalog No.
27023
Item No.
683
GLENWOOD MARINE
Allows water lines to be connected to
water cooled exhaust manifolds or
elbows with equal discharge rate.
Catalog No.
Chevrolet
27022
Oldsmobile
27024
Pontiac
27025
-21-
Item No.
682
684
685
(323) 757-3141
WATER PUMPS • IMPELLERS
MAGNAFLOW® CAM DRIVEN WATER PUMPS
1” MAGNAFLOW® WATER PUMP
The “Magnaflows®” are self-priming,
cam driven water pumps featuring
chrome brass construction, friction minimizing ball bearings, long lasting
ceramic seals and a tough neoprene
impeller. To accommodate a variety of
engine types, both “Magnaflow®”
pumps come standard with a large 1¼”
hose inlet, tapped 3/4” NPT and a pair
of 1/2” NPT outlets.
Catalog No.
Pump
60000
Impeller Kit* 60001
Item No.
1000
1001 (8 vanes)
3/4” MAGNAFLOW® WATER PUMP
Catalog No.
Pump
60034
Impeller Kit* 60034
Item No.
1009
1010 (12 vanes)
*Kits include 1 impeller and 2 “O” Rings.
“NEOVANE” IMPELLER KITS
Kits include impeller, shear pin and gasket
or “O” ring. Kits available for all models
listed below.
Repair Kit
Item No.
1018
1017
For “Neovane” Pump No.
V-505, V-755, H500 and V-750
V-105
GLENWOOD MARINE
-22-
(323) 757-3141
WATER PUMPS • BILGE PUMPS
Jabsco Water Pump
Port Size
3/4”
Impeller
Catalog No.
12100001
Pump Model
Catalog No.
58500001
Item No.
1058
Item No.
1036
Repair Kit No.
900330001
Item No.
1051
Jabsco Water Pump
Port Size
Pump Model
Catalog No.
Item No.
53309001
1035
1”
Impeller
Catalog No.
Item No.
12100001 (3/4”) 1058
9200001 (1”)
1057
Repair Kit No.
901110011 (3/4”)
901180001 (1”)
Item No.
1053
1054
Jabsco Water Pump
Pump Model
Port Size
Catalog No.
1”
7779001
1” High Speed
7779051
Impeller
Catalog No.
Item No.
Repair Kit No.
9200001
1057
901180001
Item No.
1024
1025
Item No.
1054
JABSCO BILGE
FOR BAIT TANK PUMP
JABSCO
SUBMERGIBLE
BILGE PUMP
Pump Model
Catalog No.
302202012
Item No.
1044
AUTOMATIC FLOAT SWITCH
Catalog No.
Item No.
302950000
1041
GLENWOOD MARINE
Volt D.C.
12
Pump Model
Catalog No.
18660-0121
Impeller
63030003
1062
-23-
Item No.
1038
Repair Kit No. Item No.
900610003
1052
(323) 757-3141
WATER PICK-UPS
MINIATURE WATER PICK-UP
HIGH SPEED SCOOP STRAINERS
CAST BRASS
CAST BRASS
A small streamline fitting which may be
used with centrifugal feed cooling to the
V-Drive.
Pipe I.D.:
3/8”
Water inlet fitting has a protective grate
over the intake.
Description
Brass
Chrome
Catalog No.
19731
19741
Item No.
406
408
Pipe I.D Pipe Length Catalog No. Item No.
1/2”
2-1/4”
30112
729
3/4”
2-9/16”
30134
730
1”
3”
30101
728
HIGH SPEED WATER PICK-UP
CAST BRASS
CAST BRASS
A pick-up which can be used with a
pump or centrifugal feeding the block.
Pipe I.D.:
1/2”
Description
Brass
Chrome
WATER DIVIDER TEE
Catalog No.
30230
30240
GLENWOOD MARINE
Item No.
731
732
This water divider is a must on V-8
engines to distribute an even flow of
water to both cylinder heads. The inlet is
tapped for 1/2” NPT and the outlets are
for 5/8” hose.
Description
Brass
Chrome
-24-
Catalog No.
21130
21140
Item No.
465
466
(323) 757-3141
FLAME ARRESTERS
GPI STAINLESS STEEL FLAME ARRESTERS
Equip your performance marine engine with a
U.S. Coast Guard approved GPI flame
arrester offered in nine different sizes to
accommodate a variety of popular four-barrel
Holly/Rochester and Dominator carburetor
models. GPI flame arresters are manufactured using 100% highly polished stainless
steel construction to insure maximum corrosion resistance, even in harsh saltwater environments. Each GPI flame arrester model has
been specially engineered to deliver optimum
air intake to the carburetor. Available in two
diameter sizes (8 and 10 inch) and three
heights (2, 3 and 5 inch).
Catalog No.
GFA-850-8-2
GFA-850-8-3
GFA-850-8-5
GFA-850-10-2
GFA-850-10-3
GFA-850-10-5
GFA-1050-10-2
GFA-1050-10-3
GFA-1050-10-5
Item No.
1500
1510
1520
1530
1540
1550
1560
1570
1580
ALUMINUM FLAME ARRESTERS
All aluminum flame arrester. Ideal for engines
installed in hulls using a motor box or hatch
covers. U.S. Coast Guard approved.
Air Horn
Size
2-5/8”
4-3/16
4-3/16”
5-1/8”
5-1/8”
5-1/8”
Element
Height
Height
Overall
Diameter
Cat.
No.
Item
No.
1-1/8”
1-1/2”
3”
1-1/2”
1-1/2”
3”
1-7/8”
2-3/8”
3-7/8”
1-1/2”
2-3/8”
3-7/8”
5-3/4”
5-3/4”
5-3/4”
5-3/4”
5-3/4”
5-3/4”
20922
20924
20924-A
20925-C
20925-F
20925-D
2-3/8”
1-1/2”
2-3/8”
3-3/4”
5-3/4”
5-3/4”
5-3/4”
8”
20924-B 459-B
20925-E 460-E
20925-G 460-G
20925-H 460-H
458
459
459-A
460-C
460-F
460-D
With Breathers:
4-3/16”
5-1/8”
5-1/8”
5-1/8”
1-1/2”
1-1/2”
1-1/2”
3”
GLENWOOD MARINE
-25-
(323) 757-3141
CARBURETOR TILT SHIMS
FOUR THROAT
CARBURETOR TILT SHIM - 12º
QUADRAJET TILT SHIM - 12º
CAST ALUMINUM
CAST ALUMINUM
Precision machined and drilled to fit most
four barrel carburetors with four bolt
patterns. Will not fit Holley Carburetors.
Length
6½”
Width
5”
Catalog No.
19910
Designed especially for four barrel
Quadrajet carburetors.
Catalog No.
20020
Item No.
410
TILT SHIM - 12º
TWO THROAT
CARBURETOR TILT SHIM - 12º
CAST ALUMINUM
CAST ALUMINUM
Machined and drilled to fit small block
Chevrolets with Rochester carburetors.
Length
5”
Width Catalog No.
3-3/8”
20010
GLENWOOD MARINE
Item No.
412
Designed for Holley and Carter AFB
carburetors with a 4-1/4” x 5-1/8”
or 5-5/32” x 5-5/8” bolt pattern.
Item No.
411
Catalog No.
20510
-26-
Item No.
455
(323) 757-3141
OIL FILTER BY-PASS ADAPTERS
For Use in By-Passing Standard Oil Filter to Install Remote Filter System
FORD V-8
CHRYSLER B - 1959 -1979
AND
FORD 1957 AND LATER
221, 260, 289, 292, 302, 312, 351,
400, 429 and 460 cu. in.
332, 351, 390, 406, 427 and 428 cu. in.
engines.
Catalog No.
12350
Catalog No.
12380
Item No.
48
CHEVROLET AND PONTIAC
1968 and later Chevrolet and 1971-72
Pontiac V-8s with spin-on oil filters.
Catalog No.
12390
OLDSMOBILE
350, 425 and 455 cu. in.
For spin-on type filters.
Item No.
52
GLENWOOD MARINE
Item No.
51
Catalog No.
12395
-27-
Item No.
1660
(323) 757-3141
FILTERS • COOLERS • ADAPTERS
OIL COOLERS
REMOTE
OIL FILTER
SINGLE
These oil coolers have 3/4” female N.P.T.
on each end for water. The pipe connections for oil are 1/2” N.P.T.
Easy to mount in a variety of locations.
Requires use of by-pass adapters.
Complete
Extra Filter only
Catalog No.
12401
12409
Item No.
53
54
Length
9”
12”
9” Chrome
12” Chrome
REMOTE
OIL FILTER
High capacity, high performance remote
dual filters. Requires use of by-pass
adapters.
12709
12712
12749
12742
67
68
70
69
Catalog No.
12421
12409
For remote oil filter connection.
Item No.
56
54
E-Z OIL DRAIN
FOR INBOARD BOATS
To drain oil, simply
push end of hose
through transom drain hole and remove
cap. When not in use, replace cap and
leave hose in bilge until next use. For
boat in water, attach pump. Hose is 42”
in length.
Length
Catalog No.
Item No.
12” Each
14” Each
16” Each
18” Each
22” Each
24” Each
12512
12514
12516
12518
12522
12524
58
59
60
61
62
63
OIL COOLER
BRACKETS
CAST ALUMINUM
Catalog No.
Item No.
12 X 1.75 mm
Chevy E-Z Oil Drain
3080380
1121
14 X 1.50 mm
Ford E-Z Oil Drain
3090380
1122
Catalog No.
Item No.
1125
Sandblast
Polished
12930
12940
1/2 x 20 Thread
E-Z Oil Drain
Item No.
HI-PRESSURE HOSE
DUAL
Complete
Extra Filter only
Catalog No.
3050380
GLENWOOD MARINE
To securely fasten Glenwood oil coolers,
use these sturdy aluminum brackets. Sold
per pair. Inside diameter is 2-1/8”.
-28-
71
72
(323) 757-3141
V-DRIVE AND FRONT ENGINE COUPLINGS
CRANKSHAFT
TAKE-OFF WITH V-PULLEY
CRANKSHAFT TAKE-OFF
STEEL
V-Belt pulley groove is an integral part of
this power take-off. Perfect for driving a
generator or water pump.
FOR INTERNALLY BALANCED ENGINES
ONLY. WHEN ORDERING SPECIFY
ENGINE.
STEEL
Available for most popular automotive
engines. Power take-offs used to couple
cranking end of engine to drive line.
FOR INTERNALLY BALANCED ENGINES
ONLY. WHEN ORDERING SPECIFY
ENGINE.
Drive Line
Series
Drive Line
Series
1310
1350
Catalog No.
33821
33825
Item No.
1310
1350
862
863
33811
33815
Item No.
860
861
BORG WARNER
TRANSMISSION FLANGES
V-DRIVE FLANGE TAKE-OFF
STEEL
STEEL
Drive Line
Series
Catalog No.
Bore
Size
Catalog No.
Item No.
1310
1310
1310
1310
1”
1-1/8”
1-1/4”
1-3/8”
33911
33911
33911
33911
86416
86418
86420
86422
1350
1350
1350
1350
1”
1-1/8”
1-1/4”
1-3/8”
33915
33915
33915
33915
86516
86518
86520
86522
GLENWOOD MARINE
Flanges are for the 4” and 5” diameter Borg
Warner 71 and 72, EXCEPT the 864-B and
864-E which are for a Casale C-500 ONLY.
Description
1” Male 71 B/W - 4”
339-11A
864-A
1” Male Spicer Casale- 4”
339-11B
864-B
1” Taper Male 71 B/W - 4” 339-11C
864-C
1-1/8” Male 71 B/W - 4”
339-18D
864-D
1-1/8” Male Spicer Casale - 4” 339-18E
864-E
1” Male 72 B/W - 5”
339-11A
865-A
1-1/8” Male 72 - 5”
339-18B
865-B
-29-
(323) 757-3141
FLYWHEEL POWER TAKE-OFFS
FLYWHEEL POWER TAKE-OFFS
STEEL
Precision drilled and tapped to receive
1310 or 1350 drive lines. Bolts to the
flywheel or flexplate, bolt pack included.
To determine drive line series, measure
the registration (see photo at right).
1310 Series Male Pilot - 2-3/8”
1350 Series Male Pilot - 2-3/4”
1310 DRIVE LINE SERIES
Drive Line
Catalog No.
Chevy - Automatic
Chevy - Standard
Chrysler 6 Bolt
Chrysler 8 Bolt
Ford - 272-312
Ford - 289-351
Ford - 331-460
65 Olds (425 c.i.)
66-81 Olds (350-455 c.i.)
59-64 Pontiac
65-88 Pontiac
Chevy (87 & newer) -Auto
Chevy (87 & newer) - Std
Chevy (81-86 V-6) - Auto
Chevy (81-86 V-6) - Std
1350 DRIVE LINE SERIES
Drive Line
Item No.
32710
32710
32710
32710
32710
32710
32710
32710
32710
32710
32710
32710
32710
32710
32710
Catalog No.
Buick Automatic - 55-56 32750
Cad/Oldsmobile - 49-64 32750
Chevy - Automatic
32750
Chevy - Standard
32750
Chrysler 6 Bolt
32750
Chrysler 8 Bolt
32750
Ford 2.3 Liter
32750
Ford - 289-351
32750
Ford - 331-460
32750
Olds (350-455c.i.)*66-81 32750
Pontiac - 59-64
32750
Pontiac - 65-88
32750
Chevy (87 & newer) -Auto 32750
Chevy (87 & newer) - Std 32750
Chevy LT1 - Automatic
32750
*SPECIFY IF STANDARD OR AUTOMATIC
793-E
793-F
793-G
793-H
793-I
793-J
793-K
793-L
793-M*
793-N
793-O
793-P
793-Q
793-R
793-S
*SPECIFY IF STANDARD OR AUTOMATIC
Item No.
796-A
796-B
796-C
796-D
796-E
796-F
796-G
796-H
796-I
796-J
796-K
796-M*
796-N
796-O
796-P
796-Q
796-T
CHEVROLET 1/2” SPACERS FOR AUTOMATIC FLYWHEEL FOR REVERSE ENTRY STARTERS
Big Block Chevrolet
Chevrolet (87)
Catalog No.
32710
32750
Item No.
793
796
BORG WARNER POWER TAKE-OFF
STEEL
Made exclusively to fit Borg Warner Velvet Drive
transmission for model 71 and 72 gears. Flange
adapter is drilled and tapped to receive the 1310
or 1350 drive line series.
Drive Line Series
1310
1350
1310
1350
for
for
for
for
71
71
72
72
Gear
Gear
Gear
Gear
Catalog No.
32711
32751
32712
32752
GLENWOOD MARINE
Item No.
794
797
795
798
-30-
(323) 757-3141
TORQUE TUBE • CHAIN COUPLINGS
CHAIN COUPLINGS
JET H-JOINT ASSEMBLY
CHROME MOLY STEEL, HEAT TREATED
Only the finest material and workmanship go
into the manufacturing of this coupling. 50
pitch chain - 14 teeth.
SPECIFY ENGINE AND SHAFT SIZE. A
MACHINING CHARGE WILL APPLY FOR ALL
SHAFTS OTHER THAN 1”.
Catalog No.
32050
Item No.
767
These 1310 or 1350 series H-Joints have a
1-3/8” 10-spline stub shaft which fit the
Berkeley, Jacuzzi and Bay Jet units.
Drive Line Series
1310 - 7-7/16” Long
1350 - 8” Long
Catalog No.
33744
33743
Item No.
844
843
H-JOINT ASSEMBLY
SHORT TORQUE TUBE
Identical to our custom torque tube assemblies
below. The running position lengths are listed
below.
Drive Line Series
10-1/2” 1310
11”
1350
13”
1350
Catalog No.
33701
33705
Item No.
834
835
33713
836
These 1310 H-Joints offer the shortest
possible U-Joint assemblies. Only 5½” long.
Drive Line Series
1310
Catalog No.
33751
Item No.
846
CUSTOM TORQUE TUBE ASSEMBLIES
These are the finest Spicer Tube and
U-Joint Assemblies offered in the
marine industry. Included in these
assemblies are two U-Joints, Spline
and Tube. Sizing to your requirements
is available. Give dimensions from
flange face at engine to flange face at
V-drive.
TURBO 400 DRIVE LINE IS AVAILABLE.
SPECIAL ORDER ONLY.
GLENWOOD MARINE
1310 Series
Stock Length
24”
36”
48”
1350 Series
Stock Length
Diameter of Tube Catalog No. Item No.
2½”
33721
837
2½”
33731
839
2½”
33741
841
Diameter of Tube Catalog No. Item No.
24”
36”
48”
Turbo 400 Drive Line
-31-
3”
3”
3”
33725
33735
33745
33752
838
840
845
848
(323) 757-3141
GUARDS • ADAPTERS
TORQUE TUBE GUARDS - CAST ALUMINUM
Designed to accommodate V-drives with low
angle input shafts. Bottom of guard to center
line measures 6½”. Furnished with aluminum
angle.
Catalog No.
Sandblast
Polished
33612
33622
For V-drives with steeper input shafts. Bottom
of guard to center line measures 8½”.
Furnished with aluminum angle.
Catalog No.
Item No.
Sandblast
Polished
830
832
33613
33623
Item No.
831
833
Specify Drive Line Series
Specify Drive Line Series
TORQUE TUBE GUARD TUBE TYPE - STAINLESS STEEL TUBE
Tube type guard eliminates the hazard of an
exposed rotating torque tube by completely
enclosing it. Made of corrosion resistant stainless
steel.
S.S. TUBE - POLISHED
S.S. TUBE ADAPTER SLEEVE
SATIN
FINISH
12” S.S. Tube
18” S.S. Tube
24” S.S. Tube
30” S.S. Tube
36” S.S. Tube
I.D. - 4-3/4”
Catalog No.
337512
337518
337524
337530
337536
Item No.
853
854
855
856
857
Tube adapter sleeve couples the stainless
steel tube to the V-drive adapter. Has a 5”
I.D. and a length of 12”. Approximately half
of sleeve length should cover the stainless
steel tube.
O.D. - 5”
NOTE:Requires extra 6” to go into adapter.
GLENWOOD MARINE
-32-
Catalog No.
337502
Item No.
852
(323) 757-3141
ADAPTERS
ENGINE ADAPTER
V-DRIVE ADAPTER
CAST ALUMINUM
CAST ALUMINUM
Adapts to any of Glenwood’s rear engine
mounts to accommodate stainless steel tube.
Has a 9½” O.D. and a 5” I.D. and is made
to fit our S.S. Tubes.
This adapter will fit all Casale V-drives. Has a
precision machined flange to hold the tube
adapter. Has a 5” O.D. and is made to fit our
Tube Adapter Sleeve.
Catalog No.
337500
Catalog No.
337501
Item No.
850
Item No.
851
ADAPTER FOR TURBO 400
V-DRIVE ADAPTER - C-500
CAST ALUMINUM
CAST ALUMINUM
This adapter is made for a Turbo 400 short tail
shaft transmission and made to fit our stainless steel tubes. Has a 4¾” O.D. and is made
to fit our S.S. Tubes.
This adapter will fit the C-500 Casale V-Drive.
Has a precision machined flange to hold the
tube adapter. Has a 5” O.D. and is made to
fit our Tube Adapter Sleeve.
Catalog No.
337498
Item No.
1692
GLENWOOD MARINE
Catalog No.
337599
-33-
Item No.
1693
(323) 757-3141
V-DRIVES
CASALE SPLIT CASE V-DRIVE
CASALE C-500
A direct drive V-drive for boats where a marine
transmission is coupled to the engine. An extra
heavy aluminum casting with oversize bearings
make this a very quiet gear box. V-drive is
equipped with input flange to suit torque tubes
or drive lines of our 1310 and 1350 series.
The output shaft is equipped with a flange to
couple to the prop. Shaft is 1” or 1-1/8” shaft
sizes. Comes complete with the mounting
bracket on flanges located on the thrust centerline of the V-drive.
Available in Overdrive or Underdrive Gear
Ratios of: 1.04, 1.10, 1.15, 1.22 and 1.29.
Catalog No.
355500
Item No.
929
NOTE: When ordering please specify: Overdrive or underdrive
ratio, 1310 or 1350 series input flange, prop shaft size and mounting spacing desired.
BEARING PULLER
The finest V-Drive for recreation or competition. Features water cooled case, precision
cut helical gears, heavy duty ball bearings and
a high tensile cast aluminum alloy exterior
casing. Available in direct drive or in-and-out
configuration.
10 Degree
Catalog No.
10º Standard V-Drive
35411
10º In-and-Out V-Drive 35420
10º Set of Gears
35410
Item No.
923
926
922
Specify ratio and left or right hand gears.
1.06.
1.09.
1.12.
1.15.
1.18.
1.22.
1.25.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
RATIOS (Overdrive)
37-35
1.29. . . . . . . . 40-31
37-34
1.32. . . . . . . . 41-31
38-34
1.37. . . . . . . . 41-30
38-33
1.40. . . . . . . . 42-30
38-32
1.45. . . . . . . . 42-29
39-32
1.48. . . . . . . . 43-29
40-32
1.54. . . . . . . . 43-28
Other ratios available - Special Order Only
Mounting Plate Size: 26”
12º Set of Gears
STEEL
35412
924
V-DRIVE SHIFTER
Provides quick and easy removal of bearings
in Casale Split Case V-drives.
Catalog No.
36050
Item No.
934
V-DRIVE GASKET SET
FOR SPLIT CASE V-DRIVES ONLY
Catalog No.
CASALE
Item No.
928
GLENWOOD MARINE
Ratchet type shift selector which keeps
V-Drive from sliding out of gear. Applicable
for all V-Drives.
Description
In-and-Out
In,Out and Reverse
-34-
Catalog No.
18322
18323
Item No.
335
336
(323) 757-3141
SHAFT LOGS • STUFFING BOXES
SELF ALIGNING SHAFT LOGS - CAST BRASS OR ALUMINUM
9 Degree Log:
Base Size 3½” x 18¾”
Aluminum Log
Aluminum Log - Polished
Bronze Log
Bronze Log - Chrome
Catalog No.
15610
15620
15630
15640
12 Degree Log:
Base Size 3½” x 11¾”
Aluminum Log
Bronze Log
Bronze Log - Chrome
16010
16020
16030
16040
Item No.
172
176
180
183
15 Degree Log:
Base Size 3¼” x 8½”
Aluminum Log
Bronze Log
Bronze Log - Chrome
Catalog No.
15810
15820
15830
15840
Item No.
187
191
195
199
Note: Please order the stuffing box, hose and clamps
separately.
207
211
215
219
SEAL TYPE STUFFING BOX
DOUBLE SEAL
TYPE STUFFING BOX
CAST BRONZE
Our stuffing box uses double
neoprene seals. Water must be
discharged into the stuffing
box, further lubricating the
Aqua Lube bearing insert. O.D. is 1-¾”.
For use with 1” and 1-1/8” shafts.
A neoprene seal
stuffing box furnished
in 1” or 1-1/8” shaft
sizes for shaft logs.
O.D. is 1-¾”. An
ideal stuffing box for
tight coupled
installations.
Description
Bronze - 1”
Chrome - 1”
Bronze - 1-1/8”
Chrome - 1-1/8”
Extra Seal - 1”
Extra Seal - 1-1/8”
Description
Bronze - 1”
Chrome - 1”
Bronze - 1-1/8”
Chrome - 1-1/8”
Extra Seal - 1”
CAST BRONZE
Catalog No.
16632
16642
16638
16648
16409
16489
Item No.
244
246
1663
1664
233
238
Catalog No.
16431
16441
16438
16448
16409
16489
Item No.
234
236
235
237
233
238
STUFFING BOX PARTS
HOSE
Length of Hose . . . . . . . . . . . . . . . . . . . . . . 3½”
Inside Diameter of Hose. . . . . . . . . . . . . . . . 1¾”
Outside Diameter of Hose . . . . . . . . . . . . . . 2¼”
Catalog No.
16300
GLENWOOD MARINE
STAINLESS CLAMPS
(2 required)
Item No.
232
-35-
Catalog No.
16200
Item No.
231
(323) 757-3141
SHAFT LOG AND STUFFING BOX FOR CRUISERS
HEAVY DUTY - 12° SHAFT LOG ONLY
12 Degree Log:
Base Size 3½” x 14”
Catalog No.
Heavy Duty Bronze Shaft Log Only
Accepts 2” hose only.
16500
Item No.
239
HEAVY DUTY - 12° SHAFT LOG COMPLETE
This heavy duty shaft log is made out of bronze. It is made especially for 1-1/4” shafts but may also
be used for 1-1/8” shafts. Sold as a complete unit with stuffing box, hose and clamps.
12 Degree Log
Catalog No.
1-1/4” Heavy Duty Bronze Shaft Log
1-1/8” Heavy Duty Bronze Shaft Log
GLENWOOD MARINE
16534
16538
-36-
Item No.
240
241
(323) 757-3141
STUFFING BOXES • BEARINGS • BEARING CAGES
GW MORSE-TYPE STUFFING BOX
Corrosion free, pre-packed with beveled
glands to force packing against shaft as it
is tightened. O.D. is 1-¾”.
Shaft Size Hose I.D.
1”
1-1/8”
1-3/4”
1-3/4”
Catalog No.
49409
49410
Description
Extra Packing:
*3/16”
**5/16”
Item No.
1215**
1216**
PACKING TYPE STUFFING BOX
Shaft Size
Bronze
Bronze
Bronze
Bronze
O.D. is
Catalog No.
1”
Chrome 1”
1-1/8”
Chrome 1-1/8”
1-¾”.
Catalog No.
Item No.
13700
106
Item No.
16131
16141
16138
16148
223***
227***
226*
230*
(SEE BELOW)
***1/4” - Please specify when ordering
FLANGE BEARINGS
THRUST BEARING CAGE
CAST ALUMINUM
A self-aligning flange type bearing.
Perfect for thrust installation on channel
between engine stringers.
Hi-tensil cast aluminum bracket for holding the flange type thrust bearing.
Fastens between engine stringers with
two pieces of aluminum angle.
Length
Width
Catalog No.
Item No.
23-1/2”
4-1/8”
16914
280
Shaft
Size
1”
1-1/8”
TWO HOLE FLANGE BEARING
Base
Size
3¼” x 5½”
18601
346
3¼” x 5½”
18618
347
TWO OR FOUR HOLE STANDARD DUTY
PLEASE SPECIFY TWO OR FOUR HOLE
BOLT CENTER FOR 2-HOLE IS 3-7/8”
BOLT CENTER FOR 4-HOLE IS 2-3/4” SQUARE
3/4”
7/8”
1”
3” X 3”
3¾” X 3¾”
3¾” X 3¾”
17334
17378
17301
286
287
285
MEDIUM DUTY/STANDARD DUTY
1”
GLENWOOD MARINE
-37-
4¼” X 4¼”
17401
288
(323) 757-3141
STRUTS
CRUISER SPEED STRUTS
CAST MANGANESE BRONZE
Strut is furnished in 10º angle and bored for
any 1¼” O.D. bearing. Bearing is not
included.
Strut is furnished in 12º angle and bored
for any 1¾” O.D. bearing. Bearing is not
included.
Base Size: 3½” x 7¾”
Holes: Center to Center 2-9/16” length 2-5/8” width
Length of Bearing Housing: 6-7/8”
Base Size: 5” x 8¾”
Length of Bearing Housing: 8¼”
Length of Drop
7½”
Catalog No.
11431
Item No.
18
Length of Drop
9”
11”
Catalog No.
14139
14131
Item No.
121
120
DELUXE SPEED STRUT
CUSTOM SPEED STRUT
Strut is furnished in 9º, 10º, 12º, 14º and 16º
angles. Bearings are placed in each end for less
resistance and more positive alignment. Uses
1¼” O.D. bearings. Bearing is not included.
Base Size: 3½” x 7½”
Holes: Center to Center 2½” length 2-3/16” width
Length of Bearing Housing: 8”
Length of Drop: 6¾”
Description
Bronze
Bronze
Bronze
Bronze
Bronze
Bronze
Bronze
Bronze
Bronze
Bronze
Chrome
Chrome
Chrome
Chrome
Chrome
Angle
9º
10º
12º
14º
16º
9º
10º
12º
14º
16º
Catalog No.
Item No.
14031-9
14031-10
14031-12
14031-14
14031-16
14041-9
14041-10
14041-12
14041-14
14041-16
11609
11610
11612
11614
11616
11809
11810
11812
11814
11816
GLENWOOD MARINE
Strut is furnished in 10º, 12º, 14º and 16º
angles. Bearings are placed in each end for less
resistance and more positive alignment. Uses
1¼” O.D. bearings. Bearing is not included.
Holes: Center to Center 2.100” length 3” width
Length of Drop: 7½”
Description
Bronze
Bronze
Bronze
Bronze
Bronze
Bronze
Bronze
Bronze
-38-
Chrome
Chrome
Chrome
Chrome
Angle
10º
12º
14º
16º
10º
12º
14º
16º
Catalog No.
14231-10
14231-12
14231-14
14231-16
14241-10
14241-12
14241-14
14241-16
Item No.
12210
12212
12214
12216
12410
12412
12414
12416
(323) 757-3141
STRUTS
COMPETITION STRUT
Cast of 90,000 tensile manganese bronze and
furnished in 9º, 12º or 16º angles. Available
for 1” and 1-1/8” prop shafts. Uses 1-3/8”
O.D. Bearings. Bearings are not included.
Base Size: 4” x 8½”
Holes: Center to Center 2.100” length 3” width
Length of Bearing Housing: 9½”
Length of Drop: 6¾”
Description
Bronze
Bronze
Bronze
Bronze Chrome
Bronze Chrome
Bronze Chrome
STREAMLINE STRUT
Angle
Catalog No.
Item No.
9º
12º
16º
9º
12º
16º
15031-9
15031-12
15031-16
15041-9
15041-12
15041-16
14009
14012
14016
14309
14312
14316
Furnished in 12º and 14º angles. Strut #1 is
for 12” propellers. Strut #2 is for 11” and
smaller propellers. Available for 1” shafts.
Uses 1¼” O.D. Bearings. Bearings are not
included.
#1 Strut Base Size: 3½” x 6”
#1 Strut Length of Bearing Housing: 4-5/8”
#1 Strut Length of Drop: 6¾”
#2 Strut Base Size: 3½” x 6¼”
#2 Strut Length of Bearing Housing: 5½”
#2 Strut Length of Drop: 5½”
Description
#1
#1
#2
#2
GLENWOOD MARINE
Strut
Strut
Strut
Strut
-39-
Angle
12º
14º
12º
14º
Catalog No.
Item No.
14561-12
14561-14
14551-12
14551-14
13212
13214
13012
13014
(323) 757-3141
STRUTS
WHIP STRUT
This small whip strut should be used when
running the flat shaft angles found on most
V-drive installations. Furnished in 9º and 12º
angles.
Base Size: 3” x 3”
Holes: Center to Center 1-9/16” length 2¼” width
Description
9º
9º
12º
12º
Bronze
Bronze Chrome
Bronze
Bronze Chrome
Catalog No.
14339
14349
14332
14342
Item No.
127
129
126
128
12º SPECIAL CUSTOM SPEED STRUT
Strut is furnished in 12º angle only. Bearings
are placed in each end for less resistance and
more positive alignment. Uses 1-3/8” O.D.
bearings. Bearing is not included.
Holes: Center to Center 2.100” length 3”
width
Length of Drop: 7½”
Description
Catalog No.
12º Bronze
14431-12
GLENWOOD MARINE
Item No.
12512
-40
(323) 757-3141
BEARINGS
BJ MARINE BEARINGS
The resilient rubber yields to any
abrasive particles which work
between the shaft and the bearing,
thus taking abrasive pressure off
the metal shaft. These particles
are rolled across the flat bearing
face, deposited in the open
groove, and washed out by the
lubricating water. There is minimum wearing action because
abrasives are never held tightly
between the shaft and bearing.
That is why B.J. Bearings are ideal
for tough sand conditions, why
they have a much longer life than
other types of bearings and give
maximum protection against shaft
scoring under all conditions.
Type
Shaft
Size
Albacore
Blenny
Barracuda
Bass
Blackfish
Bloater
Bonito
Broadbill
Bullhead
Cama
Carp
Catfish
Chobie
Chogset
Chub
Cod
Croaker
Devilfish
Dogfish
Dolphin
Eel
Flatfish
Flounder
Gar
Grayback
Grouper
Haddo
Hake
Halibut
Herring
Special
3/4”
1-1/4”
7/8”
1-1/4”
7/8”
1-3/8”
7/8”
1-1/2”
1”
1-1/4”
1”
1-3/8”
1”
1-1/2”
1”
1-5/8”
1”
2”
1-1/8” 1-1/2”
1-1/8” 1-5/8”
1-1/8” 1-3/4”
2”
1-1/8”
1-1/4” 1-1/2”
1-1/4” 1-3/4”
1-1/4”
2”
1-1/4” 2-1/8”
1-3/8” 1-7/8”
2”
1-3/8”
1-3/8” 2-1/8”
1-3/8” 2-3/8”
1-1/2”
2”
1-1/2” 2-3/8”
1-5/8” 2-1/8”
1-5/8” 2-5/8”
1-3/4” 2-3/8”
1-3/4” 2-5/8”
1-7/8” 2-5/8”
1-7/8” 2-15/16”
2”
2-5/8”
1-1/8” 1-3/8”
O.D.
Length
Catalog
No.
Item
No.
3”
3-1/2”
3-1/2”
3-1/2”
4”
4”
4”
4”
4”
4-1/2”
4-1/2”
4-1/2”
4-1/2”
5”
5”
5”
5”
5-1/2”
5-1/2”
5-1/2”
5-1/2”
6”
6”
6-1/2”
6-1/2”
7”
7”
7-1/2”
7-1/2”
8”
4”
18701
18702
18703
18704
18705
18706
18707
18708
18709
18710
18711
18712
18713
18714
18715
18716
18717
18718
18719
18720
18721
18722
18723
18724
18725
18726
18727
18728
18729
18730
18731
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
MARINE BEARINGS
AQUA LUBE
Water lubricated marine bearings.
Length
4-5/8”
4”
4”
GLENWOOD MARINE
-41-
I.D.
O.D.
1”
1¼”
1” 1-3/8”
1-1/8” 1-3/8”
Catalog No.
170 14
170 18
170 88
Item No.
282
283
284
(323) 757-3141
COUPLERS•COLLARS•PROP NUTS•KEYS•PINS
PROP NUT KIT
SPLIT SLEEVE
COUPLER - STEEL
STAINLESS STEEL
This type of coupler is used on V-drives with
1” shafts.
Length
O.D. I.D. Catalog No. Item No.
3½” Cad
2”
1”
34251
868
3½” Chrome 2”
1”
34261
869
SPLIT SAFETY
COLLARS - STEEL
Diameter
Catalog No.
1” Cad
21051
1” Chrome
21061
1-1/8” Cad
21058
21068
1-1/8” Chrome
Item No.
461
463
462
464
These safety collars are used on the rudder
shaft and prop shaft.
Item No.
402
403
400
401
STRUT COLLARS
STAINLESS STEEL
Catalog No.
19481
19488
GLENWOOD MARINE
Item No.
722
PROPELLER NUTS
BRASS AND S.S.
Item No.
725
726
LOCKING
PROPELLER NUTS
STAINLESS STEEL
Thread Size
3/4 x 10
Catalog No.
29901
Item No.
727
PROPELLER KEYS
These strut collars are used on propeller
shaft ahead of the strut.
Diameter
1”
1-1/8”
STAINLESS STEEL
Thread Size
Catalog No.
3/4 x 10 (Brass) 29801
Half Nut (S.S.)
29805
STAINLESS STEEL
Catalog No.
19434
19478
19401
19418
Item No.
723
COTTER PIN
Catalog No.
29501
SAFETY COLLARS
Diameter
3/4”
7/8”
1”
1-1/8”
Catalog No.
29569
STAINLESS STEEL
Size
1/4 x 1/4
Item No.
4001
4002
-42-
Catalog No.
29701
Item No.
724
(323) 757-3141
PROPERLLER SHAFTS • PULLERS
303 STAINLESS STEEL PROPELLER SHAFTS
The finest 303 Stainless Steel shafting for propeller shafts. Shafts are precision
machined with a standard propeller shaft taper, milled for ¼” key and threaded with
¾” standard thread on 1” and 1-1/8” shafts. Standard sizes are listed below or we
will cut to your specified length. Available in 1” and 1-1/8” shaft diameters.
NOTE: When ordering shafts tapered on both ends, you must specify the minor
diameter of the engine end of the shaft.
1” Shaft
Length
Catalog No.
Item No.
48”
54”
60”
66”
72”
78”
84”
90”
96”
102”
30348
30354
30360
30366
30372
30378
30384
30390
30396
30302
734
735
736
737
738
739
740
741
742
733
Length
1-1/8” Shaft
Catalog No.
Item No.
30448
30454
30460
30466
30472
30478
30484
30490
1710
1711
1712
1713
1714
1715
1716
1717
48”
54”
60”
66”
72”
78”
84”
90”
17-4 STAINLESS STEEL PROPELLER SHAFTS
Ideal for higher horse power engines or if running a 2-blade propeller. The tensil
strength is 130,000 to 135,000. Avaiable in 1” diamemter only.
Length
Catalog No.
Item No.
48”
54”
60”
66”
72”
78”
84”
90”
20348
20354
20360
20366
20372
20378
20384
20390
424
425
426
427
428
429
430
431
K-500 MONEL PROPELLER SHAFTS
The ultimate in fine propeller shafting. The tensil strength is 150,000 to 165,000
p.s.i. Ideal for 2-blade propellers. Sold per inch. Available in 1” and 1-1/8” shaft
diameters.
1” Shaft
Catalog No.
Machine Charge
31302
31302
GLENWOOD MARINE
1-1/8” Shaft
Item No.
756
757
Catalog No.
Machine Charge
-43-
31318
31318
Item No.
1720
1721
(323) 757-3141
BRONZE PROPELLERS
O.J. CUP THREE BLADE
BRONZE PROPELLER
Three blade edges are cupped and
tapered to 1-1/8”.
Diameter/Pitch
13 X 13
13 x 14
13 X 15
13 X 16
Catalog No.
3491313
3491314
3491315
3491316
Item No.
1263L
1264L
1265L
1266L
O.J. CUP FOUR BLADE
BRONZE PROPELLER
tapered to 1”.
Diameter/Pitch
12
12
12
12
12
12
12
12
13
13
13
13
13
13
14
14
14
14
14
14
14
14
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
13
13
14
14
15
15
16
16
13
13
14
15
15
16
13
13
14
14
16
16
18
18
Catalog No.
3491213
3491213
3491214
3491214
3491215
3491215
3491216
3491216
3491313
3491313
3491314
3491315
3491315
3491316
3491413
3491413
3491414
3491414
3491416
3491416
3491418
3491418
GLENWOOD MARINE
Item No.
1248L
1248R
1249L
1249R
1250L
1250R
1251L
1251R
1252L
1252R
1253L
1254L
1254R
1255L
1256L
1256R
1257L
1257R
1259L
1259R
1261L
1261R
Four blade edges are cupped and
tapered to 1”.
Diameter/Pitch
13 X 13
13 x 14
13 X 16
Catalog No.
3501313
3501314
3501316
Item No.
1267L
1268L
1270R
Diameter/Pitch
13 X 13
13 X 13
13 x 14
13 X 16
14 X 16
14 X 18
14 X 18
-44-
Catalog No.
3501313
3501313
3501314
3501316
3501416
3501418
3501418
Item No.
1271L
1271R
1272L
1274L
1276L
1278L
1278R
(323) 757-3141
STAINLESS STEEL PROPELLERS
O.J. CUP THREE BLADE
STAINLESS STEEL PROPELLER
AS OF JUNE 2005, O.J. PROPELLER NO LONGER
MANUFACTURES STAINLESS STEEL PROPELLERS.
LISTED ON THIS PAGE ARE THE ONLY TWO S.S.
PROPS THAT WE HAVE LEFT IN STOCK AS OF
01/22/08.
TWO BLADE STEEL PROPELLERS
tapered to 1”.
Diameter/Pitch
13 X 14
Catalog No.
35113
882
11-1/2 X 14
35114
883
11-1/2 X 15
35115
884
11-1/2 X 16
35116
885
12 X 13
35123
886
12 X 14
35124
887
12 X 15
35125
888
12 X 16
35126
889
Diameter/Pitch
3691314
Item No.
1372L
STANDARD PROP PULLER
CAST BRONZE
Small puller for 3 blade props
which is ideal when the prop is
located close to the strut. Pulls
from three directions.
Length: 5¾”
FOR 1” SHAFTS ONLY.
34530
870
GLENWOOD MARINE
Catalog No.
13 X 14
UNIVERSAL PROP PULLER
FOR 1” SHAFTS ONLY.
1353L
Item No.
11-1/2 X 13
Works equally well for 2 or 3
blade props. Will accommodate
propellers up to 13” in diameter
Has a single hardened bolt and
anopening of 4-5/8” maximum.
Length: 7”.
3621314
Item No.
O.J. CUP FOUR BLADE
STAINLESS STEEL PROPELLER
2 blade propellers are made of 4130
heat treated steel with a satin finish.
Specify a right or left hand rotation. If
size you need is not listed below, please
call.
Diameter/Pitch
Catalog No.
33530
-45-
829
(323) 757-3141
RUDDER STUFFING BOXES • PLATES
DOUBLE SEAL TYPE STUFFING BOX
CAST BRASS
This competition rudder stuffing box uses a double seal on
top and an “O” ring on the bottom, giving greater rudder
shaft stability and assuring a positive leak-proof unit.
Base: 3-5/16” x 3-5/16”
Holes: center to center 2-3/8”
O.D. - 1- 5/8”
Description
Catalog No.
Item No.
14631
14641
14638
14648
16409
16489
135
137
136
138
233
238
14600
139
1” Brass
1” Brass Chrome
1-1/8” Brass
1-1/8” Brass Chrome
Extra Seal - 1”
Extra “O” ring
(specify size)
SINGLE SEAL TYPE STUFFING BOX
CAST BRASS
This rudder stuffing box uses a neoprene seal. Furnished
in 1” or 1-1/8” rudder shaft size.
Base: 3-¼” x 3-¼”
O.D. - 1-½”
Description
Catalog No.
Item No.
13931
13941
13938
13948
112
114
113
115
Catalog No.
Item No.
1” Brass
1” Brass Chrome
1-1/8” Brass
RUDDER STUFFING BOX PLATE
Description
3¼” X 3¼” Brass
3¼” X 3¼” Brass Chrome
13837
13847
107
109
4” x 4” Brass
4” x 4” Brass Chrome
13839
13849
108
110
GLENWOOD MARINE
-46-
(323) 757-3141
RUDDER STUFFING BOXES
HEAVY DUTY STUFFING BOXES
CAST BRASS
Designed for rudders using a 1-1/8” shaft.
Designed for Tournament ski boat applications. This stuffing box is used with our
Tournament ski boat rudder for 1-1/8” shaft.
Base: 4” x 4”
Base: 4” x 4”
O.D. - 1-½”
O.D. - 1-½”
Description
Heavy Duty
Catalog No.
13638
Description
Tournament
Item No.
101**
Catalog No.
M/S
Item No.
1289**
MEDIUM DUTY STUFFING BOX
CAST BRASS
Base: 3¼” x 3-¼”
O.D. - 1-½”
Description
1” Brass
1” Brass Chrome
1-1/8” Brass
Description
Extra Packing:
*3/16”
GLENWOOD MARINE
**5/16”
-47-
Catalog No.
13731
13741
13738
13748
Item No.
102***
104***
103*
105*
Catalog No.
Item No.
13700
106
(SEE BELOW)
***1/4” - Please specify when ordering
(323) 757-3141
QUADRANT TILLERS • BRACKETS
CUSTOM RUDDER QUADRANT
CUSTOM TILLER
CAST BRONZE OR ALUMINUM
This heavy duty quadrant has a clamp type boss
for simple installation. The bolt locks the quadrant to the shaft. Quadrant has a 5” radius and
a 1/4” keyway for added safety.
Description
Catalog No.
1” Aluminum
1” Aluminum-Polished
1” Bronze
1” Bronze Chrome
1-1/8” Aluminum
1-1/8” Aluminum-Polished
1-1/8” Bronze
1-1/8” Bronze Chrome
12111
12121
12131
12141
12118
12128
12138
12148
Item No.
36
38
40
42
37
39
41
43
This tiller is furnished with a 1” or 1-1/8” hole.
Easy installation with clamp type single nut and
bolt design. Bolt locks tiller to shaft. Tiller has a
1/4” keyway for added safety. Length: 7”.
Description
Catalog No.
Item No.
11831
11841
11838
11848
28
30
29
31
1” Bronze
1” Bronze Chrome
1-1/8” Bronze
RUDDER POST BRACKET
CAST ALUMINUM
Hi-tensile aluminum casting for supporting the
rudder shaft. The quadrant can ride below or
above the bracket. The bracket fastens between
or on top of the engine stringers. Furnished with
1” or 1-1/8” brass bushing and aluminum angle.
Length: 3” x 28”.
Description
Catalog No.
1” Aluminum
1-1/8” Aluminum
Item No.
11911
11921
11918
11928
32
34
33
35
COMPETITION
RUDDER POST BRACKET
CAST ALUMINUM
This rudder post bracket is competition engineered. Bracket fastens between or on top of
engine stringers. Furnished with 1” or 1-/8”
brass bushing and aluminum angle.
Length: 2¾” x 26”.
GLENWOOD MARINE
Description
Catalog No.
1” Aluminum
1-1/8” Aluminum
-48-
11711
11721
11718
11728
Item No.
22
24
23
25
(323) 757-3141
RUDDERS
SPEED RUDDER*
CUSTOM WEDGE RUDDER*
Semi-wedge rudder design
with the shaft and rudder
cast in one piece. The rudder is unbalanced for the
higher speeds. Furnished in
1” or 1-1/8” shaft size.
The ultimate in fine rudders
for fast ski and speed boats.
Perfect steering qualities at
higher speed. This rudder is
wedge shaped and has the
shaft cast as an integral part
of the rudder. Furnished in
1-1/8” shaft size only.
Blade size: 6½” x 12”
Shaft length: 11-3/8”
Blade size: 5¾” x 12”
Description
1” Bronze
1” Bronze Chrome
1-1/8” Bronze
Catalog No.
Item No.
11031
11041
11038
11048
8
10
9
11
Description
1-1/8” Bronze
Catalog No.
Item No.
11238
11248
14
15
COMPETITION STEEL RUDDER*
CUSTOM CRUISER RUDDER*
4130 ALLOY STEEL
An ideal rudder for
cruisers up to 25 feet.
Offers excellent steering
control and responsive
handling. Furnished in
Our highest quality 4130 alloy
steel competition rudder.
Beautifully chrome plated.
Recommended for boats operating in a higher speed range.
Furnished in 1” and 1-1/8”
shaft size.
Shaft length: 12”
Description
1”
1-1/8”
Blade size: 7½” x 12½”
Shaft length: 14”
Catalog No.
Item No.
11101
11108
12
13
Description
1-1/8”
Catalog No.
Item No.
11338
16
*RUDDER NOT KEYED. IF YOU WANT US TO KEY RUDDER, MEASURE UP FROM
BLADE, SPECIFY WHERE YOU WANT KEYWAY AND LENGTH OF KEYWAY.
GLENWOOD MARINE
-49-
(323) 757-3141
RUDDERS
UNIVERSAL RUDDER*
SPEED RUDDER*
CAST MANGANESE
BRONZE
STAINLESS STEEL
This is the same style of rudder as
our bronze speed rudder, except
that it is made of stainless steel
and is polished to a high luster
finish. Available in 1” and 1-1/8”
shaft size.
A balanced rudder with
integral cast shaft.
Ideal for speed boats
or small cruisers.
Furnished in 1” or
1-1/8” shaft size.
Blade size: 9¼” x 9”
Shaft length: 10”
Description
1”
1-1/8”
Catalog No.
11531
11538
Item No.
Description
19
20
1”
1-1/8”
11081
11088
1160
1161
CUSTOM WEDGE RUDDER*
CAST MANGANESE
BRONZE
STAINLESS STEEL
This is the same style of rudder
as our bronze wedge rudder,
except that it is made of stainless
steel and is polished to a high
luster finish. Available in 1” and
Blade size: 5¾” x 12”
Blade size: 10” x 14”
Shaft length: 14”
1-1/8”
Item No.
CRUISER RUDDER*
A perfectly balanced
rudder for cruisers and
larger speed boats. This
rudder has an integral
cast shaft. Furnished in
Description
Catalog No.
Catalog No.
11638
Item No.
21
Description
1”
1-1/8”
Catalog No.
Item No.
11281
11288
1180
1181
GLENWOOD MARINE
-50-
(323) 757-3141
RUDDERS
CUSTOM WEDGE
CRUISER RUDDER*
TOURNAMENT
SKI BOAT RUDDER
Intended for tournament ski boat applications. Designed to
maximize steering
control and tracking
stability. Furnished
in 1-1/8” shaft size
only.
Designed for the faster
small cruisers.
Furnished in 1-1/8” shaft
size only.
Shaft length: 12”
Description
1-1/8”
Catalog No.
Item No.
120381
1267
Blade size: 8½” x 12½”
Description
Catalog No.
Item No.
6-1/8” Shaft Length
12838
1287*
10” Shaft Length
12838L
1287L
*RUDDER IS KEYED ON LEFT SIDE 12º
OFF OF 90º.
COMPETITION
STEEL SPADE RUDDER*
COMPETITION
STEEL SPEED RUDDER*
High quality 4130 Chrome
Moly, heat treated steel.
Chrome plated competition
rudder. Designed for light
cruisers with turbo systems.
Furnished in 1” or 1-1/8” shaft
size.
High quality 4130 Chrome
Moly, heat treated steel.
Chrome plated competition
rudder. Recommended for
boats operating at elevated
speeds. Furnished in 1” or
Shaft length: 12”
Description
1”
1-1/8”
Catalog No.
Item No.
11061
11068
1268
1269
Blade size: 7” x 12”
Shaft length: 12½”
Description
1”
1-1/8”
Catalog No.
Item No.
12261
12268
1290
1291
GLENWOOD MARINE
-51-
(323) 757-3141
TRANSOM BRACKETS
RUDDER TRANSOM BRACKET
CAST ALUMINUM HI-TENSILE
Designed for slanted transoms. Used
when converting outboard hulls to
inboard. Available in 1” or 1-1/8”.
Height: 6”
Width: 8½”
Depth: 8”
Description
1”
1-1/8”
Catalog No
10610
10618
Item No.
1
2
RUDDER TRANSOM BRACKET
CAST ALUMINUM HI-TENSILE
An exceptionally strong ribbed bracket.
Designed for straight or verticle transoms. Available in 1” or 1-1/8”.
Height: 6½”
Width: 7”
Depth: 7”
Description
1”
11/8””
Catalog No
10710
10718
GLENWOOD MARINE
Item No.
3
4
-52-
(323) 757-3141
FINS
CRUISER FIN
CUSTOM V- FIN
CAST BRASS OR ALUMINUM
Designed for day
cruisers. V Base is
27º included angle.
Base size: 3” x 11½”
Depth: 6¼” Holes Center to Center - 7”
Description
Aluminum
Aluminum Polished
Brass
Catalog No.
Item No.
10910
10920
10930
5
6
7
A heavy-duty custom fin designed for use
on high performance craft. Improves
turning characteristics when used in pairs.
V Base is 13º included angle.
Base size: 3½” x 8½”
Depth: 6½”
Holes Center to Center - 1-5/8” Width
6” Length
CRUISER FIN
CAST BRASS
Description
V-base fin is made for
the day cruiser. V
Base is 27º included
angle.
Aluminum
Aluminum Polished
Brass
Brass Chrome
Brass
Catalog No.
Item No.
20431
454
Base size: 4” x 7”
Depth: 8½”
Ideal fin for stabilizing
outboards and inboards.
Base size: 3” x 9”
Depth: 6-3/8”
Holes Center to Center - 1-5/8” Width
6” Length
Holes Center to Center - 2”
Description
Bronze
Bronze Chrome
Catalog No.
Item No.
17510
17520
17530
17540
289
290
291
292
GLENWOOD MARINE
293
294
295
296
A heavy-duty racing fin with
V-base. V Base is 10º
included angle.
Aluminum
Aluminum Polished
Brass
Brass Chrome
17610
17620
17630
17640
STREAMLINE FIN
Description
Item No.
CUSTOM RACING FIN
Base size: 2¾” x 9½”
Depth: 4½” Holes Center to Center - 7”
Description
Catalog No.
Catalog No.
Item No.
18530
18540
342
344
Same as above with a water pick-up.
Description
Catalog No.
Item No.
Bronze
Bronze Chrome
-53-
18531
18541
343
345
(323) 757-3141
FOOT THROTTLES • THROTTLE BRACKET
Pedal Length: 12-1/4”
Pedal Width: 4-3/4”
Base Length: 11”
Base Width: 4”
Floor to Top of Pedal: 11”
DELUXE FLOOR
MOUNT FOOT THROTTLE
This mechanical throttle has a built in return spring
and can be mounted anywhere on the floor of the
boat allowing positioning to where it is most comfortable for the driver. Cast from 356 Aluminum
and has a polished finish. *Cable not included.
Catalog No.
18000
Item No.
1283
*Order 33C cables from page 56.
Base Length: 11-1/2”
Base Width: 5-1/2”
COMPETITION FOOT THROTTLE
POLISHED ALUMINUM
Heavy duty competition mechanical foot throttle
may be mounted to the engine stringer or to a vertical block glassed to the bottom of the hull. Pedal
angle is adjustable.
*Cable not included.
Catalog No.
Item No.
16700
258
*Order 33C cables from page 56.
Pedal Width: 4”
Base Length: 8”
Base Width: 4”
Floor to Top of
Pedal: 11”
CABLE CONTROL
FOOT THROTTLE
Cast aluminum pedal with predrilled base, cable
adapters and a ball joint.
*Cable not included.
Catalog No.
17702
Polished
Item No.
306
*Order flexible throttle cable from page 56. See
Item Numbers 307 through 311.
NOTE: ALL FOOT THROTTLES ARE PUSH TO ACCELERATE
THROTTLE BRACKET
Eliminate troublesome carburetor linkage hook-up
with this throttle bracket designed for Holley carburetors. Stamped steel construction and chrome
plated. Includes cable clamp, screws and nuts.
Catalog No.
Item No.
51000
965
GLENWOOD MARINE
-54-
(323) 757-3141
HAND SHIFT • THROTTLE CONTROLS
MV CONTROL
Combines gear selector and throttle operation
in a single handle. Features a pull-out button
to disengage the shift for starting and engine
warm-up and also has a neutral safety switch.
MV-2 Standard
Control
MV-3 Right Hand
for Berkeley Jet
MV-3 Left Hand
for Berkeley Jet
Catalog No.
Item No.
306950
1214
311412
1220
311413
1221
MT CONTROL
SINGLE AND TWIN
ST CONTROL
Model ST - Uses 33-C Cable
Model ST/HD - Heavy Duty - Uses
43-C Cable
Provides remote control of either gear selector or throttle for gasoline or diesel engines
with hydraulic transmissions servicing light
loads. Can be used on a jet for reverse.
Catalog No.
Model ST
Model ST/HD
31791
39115
GLENWOOD MARINE
Combines gear selector and throttle operation in a single handle. Features a pull-out
button to disengage the shift for starting and
engine warm-up.
Item No.
1211
1212
Catalog No.
MT-3 Single
MT-2 Twin
-55-
308601
67979
Item No.
1218
1219
(323) 757-3141
CONTROL CABLES
FLEXIBLE THROTTLE CONTROL
FLEXIBLE SHIFT CONTROL
These heavy duty push-pull throttle cables have
stainless steel housing and core is covered with
plastic. Measure cable from end to end to determine length.
Same as our Flex Throttle Control Cables, except
made with plastic knob for use as dash mounted
shift or hand throttle control. Measure cable from
end to end to determine length.
Cable Length
8’
10’
12’
14’
16’
Catalog No.
17808
17810
17812
17814
17816
Item No.
307
308
309
310
311
Cable Length
8’
10’
12’
14’
16’
The 33C Cable has 10/32 threads on both ends.
Measure cable from end to end to determine
length.
Catalog No.
15306
15307
15308
15309
15310
15311
15312
15313
15314
15315
15316
15317
15318
Item No.
312
313
314
315
316
43C CABLE
33C CABLE
Cable Length
6’
7’
8’
9’
10’
11’
12’
13’
14’
15’
16’
17’
18’
Catalog No.
17908
17910
17912
17914
17916
Item No.
146
147
148
149
150
151
152
153
154
155
156
157
158
The 43C Cable has 1/4-28 threads on both ends.
Measure cable from end to end to determine
length.
Cable Length
8’
9’
10’
11’
12’
13’
14’
15’
16’
17’
18’
19’
Catalog No.
15408
15409
15410
15411
15412
15413
15414
15415
15416
15417
15418
15419
Item No.
160
161
162
163
164
165
166
167
168
169
170
171
43BC CABLE
CABLE CLAMP
STAINLESS STEEL
The 43BC Cable has 1/4-28 threads on both ends
with a bulk head fitting on one end. Measure
cable from end to end to determine length.
Securely lock your 33C
Cables with this easy to
mount stainless steel cable
clamp.
Catalog No.
15399
GLENWOOD MARINE
Item No.
159
Cable Length
10’
11’
12’
13’
14’
15’
16’
17’
18’
-56-
Catalog No.
38013-10
38013-11
30813-12
38013-13
38013-14
38013-15
38013-16
38013-17
38013-18
Item No.
1239
1240
1241
1242
1243
1244
1245
1246
1247
(323) 757-3141
PULLEYS
DOUBLE SWIVEL PULLEY
STATIONARY PULLEY
CAST ALUMINUM
CAST ALUMINUM
Same quality and precision machining as swivel
type pulley. Available in single or double pulley
configuration.
Competition double pulley set. Allows approximately 30º of swivel movement.
Pulley Diameter: 3¾”
Base Size: 1¾” x 4”
Description
Catalog No.
Single
19001
Double
19002
Pulley Diameter: 3¾”
Base Size: 1¾” x 4”
Catalog No.
Item No.
18902
393
Item No.
396
398
FRONT STEERING PULLEY
REAR STEERING PULLEY
This pulley is designed to mount on the engine
stringer. Cast of 356-T-6 Aluminum with a highly
polished finish. To be used with our Item
Number 1271.
Catalog No.
Item No.
190359
1270
Designed to mount on the outside of the engine
stringer and adjust tension of the steering cable.
Cast of 356-T-6 Aluminum with a highly polished
finish.
Catalog No.
Item No.
190358
1271
GLENWOOD MARINE
-57-
(323) 757-3141
CABLE STEERING PARTS
STEERING PARTS
Cable steering shown
complete
STEERING POST - 4”
Catalog No.
18804
Item No.
382
SPROCKET 11 TOOTH
3/4” bore with a 3/16”key
Catalog No.
18811
Item No.
1680
STEERING POST - 6¾”
Catalog No.
18806
Item No.
384
SPROCKET 17 TOOTH
STEERING POST - 10”
3/4” bore with a 3/16”key
Catalog No.
18817
Catalog No.
18802
Item No.
387
GLENWOOD MARINE
-58-
Item No.
381
(323) 757-3141
CABLE STEERING PARTS
CABLE CLAMPS
STEERING CHAIN
Securely fasten steering cables with these
copper clamps. Provides a positive lock to to
our stainless steel cable.
Diameter
Catalog No.
Item No.
3/16”
18443
340
5/32”
18432
341
Chain is 24” in length.
Catalog No.
18807
Item No.
385
STEERING SHAFTS
STAINLESS STEEL
STEERING CABLE
Description
Catalog No.
36” Steel
18838
48” Steel
18848
36” Stainless Steel
18858
48” Stainless Steel 18868
Item No.
389
390
391
392
Shafts are 3/4” in diameter with a standard
taper. Includes 5/8”-18 SAE standard lock
nut and woodruff key.
Non-corrosive, strong steering cable. Has a
high resistance to abrasion.
Diameter
Catalog No.
Item No.
3/16”
18416
338
STEERING BEARING
STEERING TURNBUCKLE
Catalog No.
18808
GLENWOOD MARINE
Catalog No.
18805
Item No.
386
-59-
Item No.
383
(323) 757-3141
STEERING • ADAPTERS
CUSTOM RACING WHEELS
COVICO CUSTOM
STEERING WHEELS
Three spoke dished steering wheel. Rim is double dipped foam and spokes are polished stainless steel. The perfect wheel for competition or
fun. Black only.
Diameter
12”
13”
Catalog No.
20220
20221
Item No.
414
415
High performance, deep dished steering wheel.
Sturdy, non-corrosive polished stainless steel
frame. Black only.
Diameter
13”
14”
Catalog No.
20222
20223
Item No.
2000
2010
CAP ASSEMBLY
AND HUB ADAPTERS
Description
Catalog No.
C. Cap Assembly
20240
Adapters
A. Rideguide
B. Teleflex
E. Steermaster
D. 3/4 Standard
B. Attwood
B. Morse
GLENWOOD MARINE
20241
20242
20243
20244
20245
20246
-60-
Item No.
417
418
419
420
421
422
423
(323) 757-3141
CAVITATION PLATE HARDWARE
DELUXE ADJUSTABLE CAVITATION PLATE HARDWARE
The deluxe kit is furnished with Item #580 bronze chrome pillow transom blocks with 7/8”
bronze bushings. The deluxe kit uses the stainless steel control arms (Item #583) which bolt
through the 7/8” control shaft (Item #593). Deluxe kit is also available with staggered stainless steel control arms. Please accompany order with drilling dimensions on control shaft
(use diagram below) and we will drill the shaft at no extra charge.
Description
Deluxe Kit
Deluxe Kit With Staggered Arm
Catalog No.
22710
22714
1” CONTROL SHAFT
7/8” CONTROL SHAFT
Drilled and spotfaced to receive our 3/4”
stainless control arms. This control shaft is
furnished with our deluxe adjustable plate
kit. Accompany order with layout on above
diagram to facilitate drilling and spotfacing.
Catalog No.
22750
Item No.
593
GLENWOOD MARINE
Item No.
577
578
Drilled and spotfaced to receive our 3/8”
stainless control arms or 7/16” x 1¼” stainless control arm. Accompany order with layout on above diagram to facilitate drilling and
spotfacing.
Description
1” Control Shaft
7/16” x 1¼” S.S. Control Arm
-61-
Catalog No.
Item No.
22760
22763
3050
3060
(323) 757-3141
CAVITATION PLATES
STANDARD CAVITATION PLATES
Our cavitation plates are adjustable and control the ride to individual preferences. Cavitation
plates are made of cad plated steel. Set includes 5/16” chrome brass plate bosses, stainless
steel turnbuckles, pins and clips and hardware for mounting. Sold per pair.
Length
18”
18”
Width
9”
9”
Transom Angle
90º
12º
Catalog No.
13490
13412
Item No.
100
99
CUSTOM CAVITATION PLATES
Our custom cavitation plates are made of stainless steel with a satin finish. Set includes 5/16”
chrome brass plate bosses, stainless steel turnbuckles, pins and clips and hardware for mounting. Sold per pair.
Length
18”
20”
30”
18”
20”
30”
Width
9”
6¾”
6¾”
9”
6¾”
6¾”
GLENWOOD MARINE
Transom Angle
90º
90º
90º
12º
12º
12º
-62-
Catalog No.
21219
21229
21239
21212
21222
21232
Item No.
468
471
474
467
470
473
(323) 757-3141
TURNBUCKLES
1/2” STAINLESS
STEEL TURNBUCKLE
Stainless steel turnbuckle for 3/8”
bosses. Easy adjustment and double
locking nuts for performance.
Uses Plate Boss - Item #472 or
Item #475.
Minimum
Maximum
Eye to Eye
Eye to Eye
Measurement Measurement
6¾”
7¾”
8¾”
9¾”
10¾”
11¾”
12¾”
13¾”
14¾”
15¾”
17¾”
19¾”
8¾”
9¾”
10¾”
11¾”
12¾”
13¾”
14¾”
15¾”
16¾”
17¾”
19¾”
20¾”
Catalog No
Item No.
13301
13302
13303
13304
13305
13306
13307
13308
13309
13310
13311
13312
3001
3002
3003
3004
3005
3006
3007
3008
3009
3010
3011
3012
Catalog No.
Item No.
13206
13207
13208
13209
13210
13211
13212
13213
13214
79
80
81
82
83
84
85
86
87
Catalog No.
Item No.
13106
13107
73
74
THREAD SIZE: 1/2-20
3/8” STAINLESS
STEEL TURNBUCKLE
Stainless steel turnbuckles for 3/8”
bosses. Easy adjustment and double
locking nuts.
Uses Plate Boss - Item #472 or
Item #475.
5/16” STAINLESS
STEEL TURNBUCKLE
Stainless steel turnbuckles for 5/16”
bosses. Allows adjustment to the
cavitation plate for ride comfort and
performance.
Uses Plate Boss - Item #469 ONLY.
GLENWOOD MARINE
Minimum
Maximum
Eye to Eye
Eye to Eye
6¾”
7¾”
8¾”
9¾”
10¾”
11¾”
12¾”
13¾”
14¾”
8¾”
9¾”
10¾”
11¾”
12¾”
13¾”
14¾”
15¾”
16¾”
THREAD SIZE: 7/16-20
Minimum
Maximum
Eye to Eye
Eye to Eye
6¼”
7¼”
8½”
9½”
THREAD SIZE: 3/8-24
-63-
(323) 757-3141
BRONZE AND STAINLESS STEEL COMPETITION BOSSES
Male bosses for 3/8” turnbuckles. Precision machined
and available chrome plated
or in stainless steel and are
2” in diameter.
Description
Bronze Chrome
Stainless Steel
Catalog No.
21230
21231
Item No.
472
475
Male bosses for 5/16” turnbuckles. Precision machined
and chrome plated and are
1-3/4” in diameter.
Description
Bronze Chrome
Catalog No.
21270
Item No.
469
STAINLESS STEEL CLEVIS
STAINLESS STEEL SCREWS
5/16” x 1/2” stainless steel
screws used to bolt cavitation
plate bosses to the plate.
Catalog No.
21220
Drilled and tapped 1/2-20 right hand
thread. Sturdy construction, precision
machined and polished.
Item No.
480
Catalog No.
22670
STAINLESS STEEL
PINS AND CLIPS
Item No.
569
CONTROL ARM
CAST MANGANESE
For connection of turnbuckles to bosses.
Stainless steel pin with Stainless E clips.
Description
Catalog No.
For 5/16” Male Boss
21242
For 3/8” Male Boss
21250
Extra Clip - 5/16”
212-4
Extra Clip - 3/8”
212-5
Item No.
476
477
485
486
STAINLESS STEEL
PINS AND RINGS
5/16” or 3/8” pins with
head and stainless steel
ring. May be used in place
of the pin and clip.
Description
5/16”
3/8”
Catalog No.
21265
21263
GLENWOOD MARINE
Item No.
479
478
Cast from 70,000 Manganese Bronze,
chrome plated. Machined for 3/4” shaft.
Use with 3/8” turnbuckles.
Description
3/8”
Catalog No.
22653
Item No.
565
STUDS, NUTS AND WASHERS
Attach bosses to the transom with these
5/16” x 2” studs, nuts and washers.
Catalog No.
21280
-64-
Item No.
481
(323) 757-3141
OVAL THRU HULL
CAVITATION PLATE HANDLE
7 position cavitation plate control handle
has the sector and lever cast of 70,000
manganese bronze, chrome plated. The
plunger rod and clevis are stainless steel.
Handle is polished and chrome plated.
Cast oval thru hull fitting for adjustable
cavitation plates. Made in 90º and 12º
angle for angled transoms.
Description
90º
12º
Catalog No.
22621
22622
Item No.
560
561
Catalog No.
22630
THRU HULL ASSEMBLY
ALUMINUM PLATE STOCK
Machined, bronze chrome plated. Has a
1/2” I.D. seal.
1/2” Seal Only
Catalog No.
22620
22609
GLENWOOD MARINE
Item No.
562
Item No.
559
556
Flat aluminum plate for fabricating cavitation plates. 6061-T6 aluminum plate.
Description
16” x 36” x .190
-65-
Catalog No.
22453
Item No.
541
(323) 757-3141
CONTROL LEVER
Cast from 70,000 Manganese Bronze and
is chrome plated. Precision machined for
3/4” or 7/8” shaft. Clevis is stainless for
1/2” shaft.
Size
3/4”
7/8”
Catalog No
22643
22647
Item No.
563
564
TRANSOM PILLOW BLOCK
Precision machined. Available in highly polished
aluminum or cast bronze chrome plated. Fitted
with a bronze bushing for 3/4” or 7/8” shaft.
Base is 1-1/8” x 3-1/16”.
Shaft
Size
3/4”
7/8”
7/8”
Description
Catalog No.
Bronze chrome (clearance)
Aluminum polished
Bronze chrome
Item No.
22723
22667
22727
579
568
580
STAINLESS CONTROL ARM
To obtain ultimate performance, it is
sometimes necessary to adjust a portion
of the cavitation plate up or down. To
accomplish this, these control arms are
available in staggered lengths. Bolts
through a 7/8” control shaft. To determine length, measure from bottom of
barrel to center of eye. Thread size is
3/8-24. Uses 3/8” pin.
GLENWOOD MARINE
From Shaft to
Center of Eye
Catalog No.
Item No.
7/8”
1”
1-1/8”
1-1/4”
1-3/8”
1-1/2”
1-5/8”
1-3/4”
1-7/8”
2”
2-1/8”
2-1/4”
22740
22741
22748
22744
22743
22745
22746
22738
22739
22742
22747
22749
583
584
591
587
586
588
589
581
582
585
590
592
-66-
(323) 757-3141
CAVITATION PLATE CONTROLS
CAVITATION FOOT CONTROL
Allows the driver to control the cavitation
plate adjustment with their foot, without
removing their hand from the steering
wheel. Includes 7/8” stainless steel shaft
keyed so pedal may be moved. Stringer
blocks have 7/8” oil lite bushings.
Catalog No.
22501
Pedal Heigth: 13-7/8”
Base Length: 11-5/8”
Item No.
543
OVERRIDE ASSEMBLY
Allows use of both a hand and foot pedal
cavitation plate control adjustment. Stainless
steel slip joint is furnished for the cavitation
handle, along with spring, collars, aluminum
angle and knuckle joint.
Catalog No.
22502
Item No.
544
ADJUSTABLE CAVITATION PLATE OVERRIDE
HOW IT WORKS
On high speed boats, quick accurate
setting of the cavitation plate is desirable
for safety and best performance. Using
a combination Foot Control and Control
Handle with an Override Assembly makes
such adjustment quick and positive.
Usually the cavitation plates are set by
the hand control to the desired pitch.
However, when quick acceleration is
desired, or when the bow of the boat
needs to be brought down instantly,
the foot control can be depressed to
override the hand control. When
the foot control is released the
cavitation plate will return to its initial
pre-set pitch.
GLENWOOD MARINE
-67-
(323) 757-3141
PICKUP KITS • HOSE
CAVITATION PLATE PICKUP KIT
STAINLESS STEEL
This stainless steel cavitation plate pickup is used to take
water from the cavitation plates to the engine.
Description
Catalog No.
Item No.
Kit complete (No. 10-AN less hose) 22350
Pickup only (No. 10-AN)
22351
Thru Hull only (No. 10-AN)
22352
Pickup only (No. 12-AN)
22353
Thru Hull only (No. 12-AN)
22354
537
538
539
542
540
BRAIDED HOSE
NEOPRENE HIGH PRESSURE
HOSE AND FITTINGS
STAINLESS STEEL
This hose is made of synthetic rubber with
stainless steel wire braid covering it.
Complete with stainless steel straight, swivel
nuts, 5/8” #10, to fit our Item #537
Cavitation Plate Pickup Kit.
Description
Catalog No.
12” of braided
hose and the fittings
22201
Item No.
Used for oil and transmission lines. This
hose has an average working pressure of
250 lbs. PSI and has an average burst pressure of 1,000 lbs. PSI per foot.
Fitting Only
I.D. Hose
Catalog No.
Item No.
1/4”
23614
616
3/8”
23638
618
1/2”
23612
615
5/8”
23658
619
3/4”
23634
617
534
WATER HOSE
Water hose for connecting water supply on
engine conversions.
I.D. Hose
5/8”
3/4”
1”
O.D. Hose
1”
1-1/8”
1-3/8”
15958
15934
15901
GLENWOOD MARINE
206
205
203
I.D. Hose
1/4”
3/8”
1/2”
5/8”
3/4”
-68-
Hose Only
Catalog No.
22914
22938
22912
22958
22934
Item No.
596
598
595
599
597
(323) 757-3141
FITTINGS • THRU-HULL • HOSE • CLAMPS
STAINLESS THRU HULL
PIPE TO HOSE FITTINGS
BRASS/CHROME PLATED
Stainless steel thru hull for 1/2” No. 8-AN
and 5/8” No. 10-AN hose fitting.
Description
No. 8-AN
No. 10-AN
Catalog No.
19850
19860
Item No.
409
1770
STAINLESS THRU HULL
Pipe Size
1/8”
1/4”
3/8”
3/8”
3/8”
1/2”
1/2”
3/4”
3/4”
3/4”
Hose Size
3/8”
3/8”
3/8”
1/2”
5/8”
5/8”
3/4”
3/4”
1”
5/8”
25600-01838
666
25600-01438
665
25600-03838
669
25600-03812
668
25600-03858
670
25600-01258
664
25600-01234
1750
25600-03434
667
25600-03410
1751
25600-03458
1752
Pipe Size
Hose Size
Catalog No.
Item No.
25600-91438
25600-93812
25600-93858
25600-91258
25600-91234
25600-93434
25600-93838
25600-93410
672
674
675
671
1760
673
1761
1762
Stainless steel thru hull used for overboard
water discharge. Use 1/2” hose.
Catalog No.
19550
Item No.
404
HOSE CLAMPS
1/4”
3/8”
3/8”
1/2”
1/2”
3/4”
3/8”
3/4”
STAINLESS STEEL
Minimum
Diameter
7/32”
7/16”
1/2”
9/16”
11/16”
13/16”
13/16”
1-1/6”
1-5/16”
1-9/16”
1-13/16”
2-1/16”
2-5/16”
2-9/16”
2-13/16”
3-1/6”
3-5/16”
3-9/16”
4-1/16”
Maximum
Diameter
5/8”
25/32”
29/32”
1-1/16”
1-1/4”
1-1/2”
1-3/4”
2”
2-1/4”
2-1/2”
2-3/4”
3”
3-1/4”
3-1/2”
3-3/4”
4”
4-1/4”
4-1/2”
5”
33405
810
33406
811
33408
812
33410
813
33412
814
33416
815
33420
816
33424
817
33428
818
33432
819
33436
820
33440
821
33444
823
33448
824
33452
825
33456
826
33460
827
33464
828
33472
1638
GLENWOOD MARINE
3/8”
1/2”
5/8”
5/8”
3/4”
3/4”
3/8”
1”
EXHAUST HOSE
CORRUGATED WITH WIRE
Pipe O.D.
Hose I.D.
Catalog No.
2-7/8”
2-7/8”
3-1/2””
3-1/2”
4”
4”
NOTE: EXHAUST HOSE
RETURNABLE.
-69-
Item No.
21927
520
21935
521
21940
522
CUT TO SIZE IS NOT
(323) 757-3141
DRAINS
TRANSOM BAILER PLUGS
The perfect way to securely seal your transom. Bailer plugs
furnished with or without brass sleeve and with “T” handle
type stopper. Tube fits 1” hole.
Description
Screw Type - Complete
Screw Type - Plug Only
Chrome Screw Type - Complete
Chrome Screw Type - Plug Only
Tube Only
Catalog No.
Item No.
21732
21731
21742
21741
21639
512
511
514
513
510
AUTOMATIC DRAIN PLUG
Automatically allows water to exit your boat while under way.
Closes with water pressure when stopped. Plug measures 2” x 2”.
Description
Catalog No.
Item No.
Black Only
22030
524
GARBOARD DRAIN PLUG
CAST BRONZE/CHROME PLATED
A neat, efficient fitting designed for drain or washout plugs. Two
drains are usually used - one on each side of the keel in the transom.
Flange Diameter: 2”
Pipe Size: I.D.
1/2”
Pipe Size: O.D.
1”
Flange Diameter: 2½”
Pipe Size: I.D.
1”
Pipe Size: O.D.
1½”
GLENWOOD MARINE
Catalog No.
Item No.
25741
676
Catalog No.
Item No.
25781
1780
-70-
(323) 757-3141
DECK HARDWARE
SMALL HATCH VENTILATOR
COWL VENTILATOR
CAST BRONZE
CAST BRONZE
Length: 4¼”
Height: 2”
Width: 3 5/8”
Length: 6 1/2”
Height: 1 1/2”
Width: 3 7/8”
Cowl ventilator has twist on hose flanges.
Chrome Plated
Catalog No.
23040
Item No.
600
Chrome Plated
STANDARD
STREAMLINE VENTILATOR
Catalog No.
24045
Item No.
1286
CUSTOM LIFTING EYE
CAST BRONZE
Length: 4 7/8”
Height: 1¾”
Hole Size: 1”
Length: 4¾”
Height: 2”
Width: 4½”
An Ultra-Streamline Lifting or Ski Tow eye.
Boss tapped for 1/2” standard thread.
Chrome Plated
Catalog No.
23540
Item No.
614
Chrome Plated
DELUXE HATCH VENTILATOR
Catalog No.
28740
Item No.
700
TRANSOM MOUNT SKI TOW
CAST BRONZE
Length: 5½”
Height: 1¾”
Width: 5”
Chrome Plated
Catalog No.
24040
GLENWOOD MARINE
Item No.
620
Polished
Stainless Steel
-71-
Catalog No.
Item No.
21500
492
(323) 757-3141
SKI TOWS • BOW EYES
SKI TOWS
These ski tows attach directly to the engine. Available for either front or rear mount
position. Made of stainless steel and are electro-polished.
Description
Catalog No.
Item No.
21501
493*
Oldsmobile - 455 - Ski Tow - Front
Oldsmobile - 455 - Ski Tow - Rear-Tall 21509
495
Chevy - Small Block - Ski Tow - Front
21511
496
Chevy - Small Block- Ski Tow - Rear
21512
497
Chevy - Big Block - Ski Tow - Front
21531
498
Chevy - Big Block - Ski Tow-Front/Rear 21533
500
Chevy - Big Block - Ski Tow-Front-Tall
21538
501
Chevy - Big Block - Ski Tow -Rear- Tall 21539
502
Ford 460 -
Ski Tow - Rear
21564
506
Ford 460 -
Ski Tow - Front/Rear
21565
507
ALL SKI TOWS ARE AT APPROXIMATELY CARBURETOR HEIGHT.
Front Ski Tows are for V-Drive Boats
Rear Ski Tows are for Jet Boats
*This ski tow is available in steel chrome plated ONLY.
BOW EYES
U-TYPE BOW EYES
STAINLESS STEEL
CAST MANGANESE
BRONZE CHROME
Easy to install. Extremely sturdy.
70,000 lbs. p.s.i. tensile strength.
Description
3/8” Bow Eye
7/16” Bow Eye
Catalog No.
28630
28670
GLENWOOD MARINE
Item No.
698
699
Shank
Length
6”
-72-
I.D.
Eye
Shank
Size
Catalog
No.
Item
No.
1”
7/16”
28846
701
(323) 757-3141
DECK MOUNTS • GAUGE BEZELS
DECK TACH MOUNT
DECK GAUGE MOUNT
CAST ALUMINUM
CAST ALUMINUM
Mounts on deck or cowling for easy visibility
of tachometer. Accomodates 3 3/8” diameter
tachometers. Polished aluminum.
Catalog No.
Item No.
24520
631
Matches our deck tachometer mount.
Accommodates 2 1/16” diameter gauges.
Polished aluminum.
Catalog No.
Item No.
24530
632
INSTRUMENTATION BEZELS
Upgrade the appearance of your dash panel with the addition of custom machined,
anodized aluminum instrumentation bezels. Bezels are offered in polished and four
colors, flat or angled cut.
Flat - 3-3/8”
Tachometer & Speedometer
Angled - 3-3/8”
Tachometer & Speedometer
Description
Catalog No.
Item No.
Black
Blue
Gold
Red
AG-338-BLK
AG-338-BLU
AG-338-GOL
AG-338-RED
2410
2420
2430
2440
Description
Catalog No.
Item No.
Black
Blue
Gold
FL-338-BLK
FL-338-BLU
FL-338-GOL
2610
2620
2630
Angled - 2-1/16”
Gauges
Description
Catalog No.
Black
Blue
Gold
Red
AG-2116-BLK
AG-2116-BLU
AG-2116-GOL
AG-2116-RED
GLENWOOD MARINE
Flat - 2-1/16”
Gauges
Item No.
2510
2520
2530
2540
Description
Polished
Black
Blue
Gold
Red
-73-
Catalog No.
FL-2116-POL
FL-2116-BLK
FL-2116-BLU
FL-2116-GOL
FL-2116-RED
Item No.
2700
2710
2720
2730
2740
(323) 757-3141
GAUGES
STEWART WARNER
ELECTRICAL TACHOMETER
Features Zener circuitry. Has a
constant voltage supply without
use of battery and an easy to
read 250º full sweep dial. Sturdy,
one piece construction requires
no sender except for application
on diesel engines.12 volt.
Reads 0-8,000.
Catalog No.
82170
Item No.
985
STEWART WARNER TACHOMETER CABLES
Description
6’
7’
8’
9’
10’
11’
12’
Catalog No.
53506
53507
53508
53509
53510
53511
53512
JONES MECHANICAL
TACHOMETER
Item No.
966
967
968
969
970
971
972
CASALE TACH
DRIVE ASSEMBLY
Mechanical activation. Perfect
for high performance applications.
Dial readings from 1,000 to
10,000 RPM. Calibrated 2:1.
SPECIFY TYPE OF V-DRIVE
Description
Catalog No.
Tach With Tattletail 24102
Item No.
622
This is a one piece unit and will fit most Casale
V-Drives.
Catalog No.
33399
Item No.
809
Catalog No.
Item No.
JONES TACHOMETER CABLES
Description
6’
7’
8’
9’
10’
11’
12’
Catalog No.
24106
24107
24108
24109
24110
24111
24112
GLENWOOD MARINE
Item No.
623
624
625
626
627
628
629
Drive Clutch
Drive Pig Tail
-74-
33302
33303
806
807
(323) 757-3141
GAUGES • SENDERS • ALTERNATORS
STEWART WARNER GAUGES
2-1/16” DIAMETER CASE
Stewart-Warner marine gauges have heavy duty
construction internal parts for accuracy,
long life and resistance to vibration, shock
and extremes of temperature. Bezels are
chrome plated and dials are black and white.
HOBBS HOUR METER
BLOCK TEMPERATURE GAUGE
A must for every boat to
keep accurate record of
engine service hours.
Electric gauge - built by
Stewart-Warner. 2¼” dia.
Catalog No.
23100
Description
Catalog No.
Item No.
Fuel Level
E-1/2-F (12V)
82111
987
Vacuum
0-30” Vacuum
82117
992
Pressure
0-80 lbs. Oil
82322
994
0-80 lbs. (12V)
82113
989
0-100 lbs. Oil
82323
995
0-10 lbs. Fuel
82319
993
Temperature
60º-240º Water (12V) 82114
990
100º-270º Oil (12V)
82115
991
Ammeters
60-0-60 Amperes
82108
986
Voltmeter
10-16 Volts (12V)
82112
988
Some of the above require senders - see below.
STAINLESS STEEL
Attaches directly to the engine
block. Reads cylinder head
or block temperature. 3/8”
N.P.T. thread, 2¼” dia.
23200
602
Item No.
601
SENDERS FOR MARINE GAUGES
WATER TEMPERATURE
Pipe Size
1/8”
1/4”
3/8”
1/2”
OIL TEMPERATURE
1/4”
3/8”
1/2”
UNIV.
FUEL TANK (Specify left or right)
Description
6”-12” depth - LH Arm
6”-12” depth - RH Arm
10”-15” depth - LH Arm
10”-15” depth - RH Arm
15½”-24” depth - LH Arm
15½”-24” depth - RH Arm
OIL PRESSURE
Pipe Size
1/8”
GLENWOOD MARINE
Catalog No.
362-CZ
362-AN
362-AJ
362-AH
Item No.
978
977
976
975
334-AA
334-AB
334-AD
280-ED
997
998
999
974
Catalog No.
385-B
385-C
391-A
391-B
391-C
391-D
Item No.
981
981
982
982
983
983
Catalog No.
82511
Item No.
973
-75-
(323) 757-3141
SWITHCES
MARINE SWITCHES - ALL BRASS CONSTRUCTION
All brass ignition switch. Two terminal single
throw “OFF/ON”. Furnished with chrome plated
brass face nut, brass lock nut and stainless steel
springs. Mounting bushing is 1-5/16” long, and
13/16” in diameter. Overall dimensions are 25/16” long and 1-1/4” in diameter.
Accommodates 1” panel.
All brass ignition starter switch. Three position
“OFF/IGNITIION/START”. Returns automatically from start to ignition position. Furnished
with chrome plated brass face nut, brass lock
nut and stainless steel springs. Mounting
bushing is 1-5/16” long, and 13/16” in diameter. Overall dimensions are 2-½” long and 1¼” in diameter. Accommodates 1” panel.
Catalog No.
34600
Catalog No.
34600
Item No.
871
Insulated type push
bottom starter and horn switch. Mounting bushing is 1¼” long, and 7/8” wide. Supplied with
brass chrome plated face nut, brass washer, back
up nut and stainless steel springs. Accommodates
1” panel.
Catalog No.
34600
Item No.
873
Item No.
872
Push-Pull switch.
Mounting stem is
1¼” long, and 3/8” in diameter. Overall
dimensions are 3-1/8” long and 7/8” wide.
Furnished with brass hex back up nut, brass
washer, brass chrome plated face nut, brass
chrome plated 3/4” knob and stainless steel
springs.
Catalog No.
34600
34600
Item No.
874
1920 (Plasticized)
Plasticized body. Rubber cap snaps over special face nut for moisture
and dirt protection. Two 18 gauge plasticized wire leads are 12” long.
Mounting stem is 5/8” 32 thread, and is 15/16” long. Fits panels up through 1/2” thick. Two positions, “OFF/ON”. On with button depressed, spring return to off.
Catalog No.
34600
Item No.
1930
GLENWOOD MARINE
-76-
(323) 757-3141
NUTS • BOLTS • WASHERS
FLAT HEAD
MACHINE SCREWS
Catalog No.
1/4-20 x 1
1/4-20 x 1½
1/4-20 x 2
1/4-20 x 2½
1/4-20 x 3
1/4-20 x 3½
5/16-18 x 1
5/16-18 x 1½
5/16-18 x 2
5/16-18 x 2½
5/16-18 x 3
5/16-18 x3½
3/8-16 x 1
3/8-16 x 1½
3/8-16 x 2
3/8-16 x 2½
3/8-16 x 3
3/8-16 x 3½
STANDARD NUTS
Catalog No.
1/4-20
5/16-18
3/8-16
Item No.
1063
1064
1065
1066
1067
1068
1069
1070
1071
1072
1073
1074
1075
1076
1077
1078
1079
1080
LOCK NUTS
Catalog No.
1/4-20
5/16-18
3/8-16
1/4-20 x 1
1/4-20 x 1½
1/4-20 x 2
1/4-20 x 2½
1/4-20 x 3
1/4-20 x 3½
5/16-18 x 1
5/16-18 x 1½
5/16-18 x 2
5/16-18 x 2½
5/16-18 x 3
5/16-18 x3½
3/8-16 x 1
3/8-16 x 1½
3/8-16 x 2
3/8-16 x 2½
3/8-16 x 3
3/8-16 x 3½
Catalog No.
1/4”
5/16”
3/8”
GLENWOOD MARINE
Item No.
1105
1106
1107
FLAT WASHERS
Catalog No.
1/4”
5/16”
3/8”
Item No.
1081
1082
1083
1084
1085
1086
1087
1088
1089
1090
1091
1092
1093
1094
1095
1096
1097
1098
Item No.
1102
1103
1104
LOCK WASHERS
HEX HEAD CAP SCREWS
Catalog No.
Item No.
1099
1100
1101
Item No.
1108
1109
1110
STRINGER WASHERS
Aluminum stringer washers available in 1/4”, 5/16” and 3/8”.
Plain or anodized.
Size
Plain
Item No.
1/4”
1111
5/16” 1112
3/8”
1113
-77-
Black
Item No.
111101
111201
111301
Blue
Gold
Item No. Item No.
111102
111202
111302
111103
111203
111303
Red
Item No.
111104
111204
111304
(323) 757-3141
ALTERNATORS • BATTERY BOXES
ALTERNATOR BRACKET
CAST ALUMINUM - Ideal for all applications.
A universal alternator bracket.
Catalog No.
41396
Item No.
957
BATTERY BOXES
THESE BATTERY BOXES ARE BEING DISCONTINUED - SEE THE
CLEARANCE PAGE FOR SPECIAL PRICING
Rigid-mount battery boxes. Strong, lightweight heattreated aluminum construction. Corrosion protected
by long lasting black powder coat finish. Non-conductive,
no sparks. Ideal battery box for all marine and automotive applications. Easy floor mount installation.
Available in two sizes.
Description
Group 24 (6¾” x 10¼”)
Group 24 (6¾” x 10¼”) with stainless steel hardware
GLENWOOD MARINE
-78-
Catalog No.
22124
22124-S/S
Item No.
1840
1845
(323) 757-3141
BOAT BUILDING BOOKS
GLEN-L BOOK OF BOAT DESIGNS
This Glen-L catalog covers a wide variety of designs for inboard, outboard,
je, sail dinghies, SK types, cruisers, cats and houseboats. All types of boats
with sizes ranging from 8’ to 36’ are presented. Designed by a Naval
Architect, the large scale plans, full-size patterns and frame kits include
complete written and pictorial step-by-step instructions and material listings. Glen L’s easy-to-follow instructions is the one way to build your boat
right from the start.
Item No. 1136
GLEN-L SERIES - BOAT BUILDING WITH PLYWOOD
This book covers plywood and its use in building small boats. A practical, hardcover book for the amateur or professional. The author, Glen L. Witt, takes you
step-by-step from lofting to finish. This is one book that is basic, simple and
helpful.
Item No. 1133
GLEN-L BOOK OF INBOARD MOTOR INSTALLATIONS
This hard-cover book covers how to install inboard engines in a various power
boats. It gives you the basic working knowledge of inboard propulsion systems
and the installations. Includes: Tolerance and standards for clearance, sizes
and types of fittings for various installations, parts and step-by-step procedure of
automobile engine conversion.
Item No. 1132
GLEN-L SERIES - HOW TO BUILD BOAT TRAILERS
A book for everyone who trailers a boat. This practical soft-cover book is
intended for building your own trailer and also for any individual contemplating the purchase of a trailer or who trailers a boat. The book covers trailers
from undercarriages through frame construction, to launching and boat trailer
handling procedures. The numerous drawings, photos and charts illustrate
almost every phase of the working parts of a boat trailer.
Item No. 1134
HOW TO FIBERGLASS BOATS
This soft-cover book takes you through the basic procedures of fiberglassing
boats. From materials and tools to safety, this step-by-step book will show you
how to do the job right.
Item No. 1135
GLENWOOD MARINE
-79-
(323) 757-31419
HISTORY OF GLENWOOD MARINE
Glenwood Marine began in the Witt Family garage in 1944.
Since then, Glenwood has grown and continues to develop and manufacture
marine engine equipment and underwater gear for V-Drive and jet boat
applications.
Glenwood still remains in the Witt Family, and is now in its third generation.
GLENWOOD MARINE
-80-
(323) 757-3141

catalog-09-09-09 - complete.qxp

Transcription

Similar documents

The 1897 Sears, Roebuck and Co. Catalog

ARI Partsmart Flyer

ARI Part Smart Flyer

xpedx.com 2.0.16 Release Notes

RAYPAK REPLACEMENT PARTS

KELLOGG SWITCHBOARD AND SUPPLY COMPANY

NAEIR Fact Sheet

Friday, August 21, 2009 Time: 6:00 PM

Alumex - xintex group

Woodshop News