glider rocker

GLIDER ROCKER
Sand Chair & Ottoman
Model # 164100A-002
IMPORTANT:
RETAIN FOR FUTURE REFERENCE, READ CAREFULLY
Congratulations on your purchase of the
Childcare Glider Rocker Chair and Ottoman.
Safety Precautions
Read all instructions before assembly and use of the rocker chair and
ottoman. Keep instructions for future use.
WARNING
ADULT ASSEMBLY REQUIRED:
• DUE TO THE PRESENCE OF SMALL PARTS DURING
ASSEMBLY, KEEP OUT OF REACH OF CHILDREN
UNTIL ASSEMBLY IS COMPLETE
CRUSH AND AMPUTATION HAZARDS:
• A CHILD’S HANDS CAN BE TRAPPED IN MOVING
PARTS OF THE ROCKER CHAIR OR OTTOMAN.
• ALWAYS ENSURE CHILD’S HANDS ARE CLEAR
FROM MOVING PARTS OF THE ROCKER CHAIR OR
OTTOMAN.
• ENSURE THE FABRIC COVERS OVER THE CHAIR AND
OTTOMAN BASES ARE FITTED AT ALL TIMES
• CARE SHOULD BE TAKEN AS THE UNDERSIDE
MECHANISM OF THIS GLIDER COULD PRESENT A
HAZARD TO OTHER PEOPLE WHEN IN USE
• THE FOOTSTOOL IS INTENDED TO BE USED FOR
SUPPORTING THE FEET AND LEGS ONLY, NOT FOR
SITTING ON
• DO NOT SIT ON THE EDGE OF THE SEAT, ARMRESTS
OR ON THE BACKREST AS THIS COULD CAUSE THE
CHAIR TO TIP OVER
• DO NOT USE THE CHAIR AS A STEP STOOL
• DO NOT LEAVE CHILDREN UNATTENDED ON OR
BESIDE THE GLIDER AND FOOT STOOL
This product has been designed and developed with
safety, comfort and functionality in mind. Please take
the time to read this manual carefully before using
this product and keep it in a safe place for future
reference.
Contents
Assembly Contents
Assembly Instructions
Care Instructions
Due to variations in the style and design of our products, the photographs and illustrations
shown in this instruction manual are generic, therefore product fabrics, colour and
design may vary from images shown. CNP Brands reserves the right to alter product
specifications without notice as a result of our ongoing policy of product improvement.
3
Assembly Instructions
Assembly Contents
Check what you have received...
Assembling chair frame
You have received 1 box. Please check the contents of the box against the list below. If anything is
missing, please contact Customer Service. In Australia, contact CNP Brands on 1300 667 137, in
New Zealand contact Wainhouse Distribution on 0800 567 5000.
1.
Unfold backrest of chair frame.
2.
Insert T bush into both sides of the
hole in the backrest frame.
3.
Insert 50mm bolt through the
T bush so it is pointing to the
outside of the chair.
4.
Place plastic spacer onto bolt.
5.
Tighten bolt onto locating tube on armrest using the allen key.
Repeat steps 2-5 to assemble other side.
Supplied loose in box:
50mm Bolt
Chair frame
x2
x1
45mm Bolt
Seat cushion
x1
(Dome head)
x4
16mm Bolt
Armrest Pads
(L + R)
x2
(Dome head)
x4
Rocker frame
Ottoman frame
x1
base cover
x1
Ottoman frame
Ottoman cushion
x1
base cover
x1
WARNING: Ensure screws are secure but not over-tightened.
T Bush
x4
Allen key (sml)
x1
Plastic spacer
x2
Allen key (med)
x1
4
5
Assembly Instructions
Assembly Instructions
To attach seat cushion
Assembling armrests
1.
Slide pocket on top rear of seat cushion over the top of the seat
frame.
1.
Place armrest into position on the seat frame. Ensure the correct
armrest is located on the correct side, as indicated by stickers
on the frame and armrests.
2.
Pull cushion down until it is completely in position.
2.
Secure the armrests using 45mm bolts and tighten with allen
key. Secure the velcro tabs on the armrests around the bottom
bar of the seat frame as shown.
3.
Slide pocket underneath base of seat cushion over the front of
the seat frame.
3.
Repeat steps 1-3 to assemble other side armrest.
4.
Hook seat cushion loops onto the pins.
Fitting fabric base cover
1.
6
Secure cover to rear of seat frame by wrapping velcro around
rear bar as shown.
7
Assembly Instructions
Assembly Instructions
Fitting fabric base cover
(continued)
Assembling ottoman
1.
Place fabric ottoman cover over frame of ottoman.
Pass sides of cover behind frame and armrests as shown.
2.
Turn ottoman over, and secure velcro loops around bottom of
ottoman frame.
4.
Attach lowermost velcro loops
on cover front around rocking
mechanism frame as shown.
3.
Place ottoman frame onto ottoman cushion.
5.
Attach uppermost velcro loops
around sea frame as shown.
4.
Secure ottoman cushion onto frame using 16mm domed head
screws. Tighten using allen key.
2.
Attach velcro loops on top and
bottom of rear fabric around frame
as shown. Repeat for loops on
other side of rear.
3.
4.
6.
8
Join the two velcro ends of the fabric cover together.
5.
9
Assembly Instructions
Assembling ottoman (continued)
5.
Fasten velcro loops on ottoman sides around base of ottoman
frame
Care Instructions
Cleaning
To ensure the long-lasting use of your rocker chair, wipe down with a damp cloth and use a mild
soap solution if necessary. Do not use abrasive cleaners. Always store product in a clean dry place.
Maintenance
Always check parts regularly for tightness of screws, nuts and other fasteners – tighten or replace
if required. To maintain the safety of your rocker chair, seek prompt repairs for bent, torn, worn or
broken parts. Use only those parts and accessories approved by CNP Brands.
Adjusing backrest
To adjust backrest, push lever down and slide base of cushion
forwards or backwards.
10
11
Distributed in Australia by CNP Brands, 20 Calarco Drive, VIC, 3030
Customer Service 1300 667 137 www.cnpbrands.com.au
Distributed in New Zealand by Wainhouse Distribution, 2-6 Argyle St,
Morningside, PO Box 41-014, St Lukes, Auckland, New Zealand
Customer Service: 0800 567 5000 [email protected]