Diagram of completed installation

OUTLANDER
Diagram of completed installation
AUDIO NAVI SYSTEM
INSTALLATION BRACKET KIT
INSTALLATION MANUAL
WARNING
AUDIO NAVI SYSTEM
• Read these installation instructions thoroughly prior to starting installation work.
• Wiring should be performed after disconnecting the negative terminal of the battery. Otherwise , it may
cause electric shock or physical injury.
• This equipment is specific to vehicles equipped with 12V DC negative ground systems. Do not install it in
any vehicle equipped with a 24V system , such as a large truck or diesel powered automobile equipped
for cold regions. Such usage causes danger of fire.
• All cords should be kept together to avoid interference with driving operations. It is dangerous if they wind
around the steering column , gear shift lever or break pedal.
• If any cord comes in contact with a burr (sharp projection formed during the manufacture of parts) or any
other sharp object , protect the cord covering with tape to avoid damage. Any damage to the covering
may be a cause of fire or electric shock.
• Never install in a manner that blocks front visibility , interferes with normal driving operations of the steering wheel, gear shift lever or brake pedal or creates a danger to any passenger in the case of a sudden
stop. It may be the cause of a traffic accident or injury.
• Be sure to use all the accessory components as instructed and attach them securely. Never use a part
other than that specified. Use of such a part may cause danger of damage to the internal components of
the unit or loosening or detachment of components.
• When attaching the ground to bolts or nuts attached to the vehicle , never use those of any safety related
component such as the steering , brake system or fuel tank. Such usage may cause accidents.
• After completion of the wiring and installation work , ensure that all electric components , such as the brake
system, lights , horn and turn signal lights operate normally as before the installation. If operation is not
normal , find the cause by checking the wiring to make sure it is proper. Use with unknown problems may
be the cause of fire , electric shock and accidents.
• Never disassemble or modify the unit. It may be the cause of accident , fire or electric shock.
• If any abnormality , such as penetration by any foreign material , splashing , smoking or abnormal odors
occurs, stop use immediately and contact the dealer you purchased the unit from or a local service shop .
Continuing use may be the cause of accidents , fire or electric shock.
mb680a
Needed Tools
Ornament Remover
Screwdriver
Components
A-1.Audio Navi unit
A-2.Screw (M5x8)
A-3.Harness
A-4.Installation Manual
A-5.Option Coding
×8
System wiring layout
A-3.Harness
INSTALLATION BRACKET KIT
A-1.Audio Navi WPKV
32 Pin connector
B-1.CAN BOX
B-2.GPS Antenna
B-3.Bracket Assy
B-4.Bracket CAN BOX
B-5.Panel
B-6.Harness
B-7.Screw Tapping(M5×16)
B-8.Screw Tapping(M5×14)
B-9.Screw
B-10.STICKER
(Rockford Fosgate )
12 Pin connector
7 Pin connector
17 Pin connector
5 Pin connector
3 Pin connector
×2
B-2.GPS Antenna
Radio antenna plug( for Vehicle side )
×4
×5
B-11.Instruction
Manual
A-1.Audio Navi WPKV
12 Pin connector
3 Pin connector
A-3.
Harness
5 Pin connector
17 Pin connector
32 Pin connector
7 Pin connector
24 Pin connector
20 Pin connector for Vehicle side
10 Pin connector
B-1.CAN BOX
18 Pin connector
B-6.Harnes
N871LXXXXX 2009.XX epc-0393-2
1
6
Remove the center air outlet panels.
Remove the shipping bracket.
(The removed bracket and screw will not be used.)
11 Attach the audio navi unit (A-1) to the vehicle using
screw tapping (B-8).
B-8 Screw
tapping 4
mb674_ne
2
Screw×8
Shipping Bracket×2
Center air outlet panels
mb175a
A-1 Audio Navi unit
A-3.Harness
Rear view
Remove the two screws and remove the center
unique panel.
Disconnect the hazard switch connector.
A-1 Audio navi unit
mb678
Hazard switch connector
12 Attach the center upper panel using 4 screws (vehicle
part).
Connect the hazard switch connector and attach the
panel (B-5) using 2 screws (vehicle part).
Install the harness (A-3) as shown in the diagram.
7
Screw(2)
Attach the audio navi system (A-1) to the bracket
assy (B-3) using the screws (A-2).
A-2
Screw(8)
Center unique panel
Hazard switch
3
Center upper panel
Screw 4 (vehicle part)
mb176a
Remove the 4 screws and remove the audio unit
(vehicle part).
Note The removed audio unit Screws and
bracket will not be used.
Screw 2 (vehicle part)
mb674
A-1Audio navi unit
B-3 Bracket Assy
8
Attach the CAN BOX (B-1) to the bracket assy (B-3)
using the bracket CAN BOX (B-4) and 5 screws
(B-9).
B-9 Screw ×5
B-5 Center panel
Screw 4
mb679
13 Attach the center air outlet panels.
Audio unit
mb703
Hazard switch connector
4
B-1 CANBOX
Remove the 4 screws and remove the center upper
panel.
B-4 Bracket CAN BOX
Center upper panel
mb675
Screw 4
9
Attach the harness (B-6) to the bracket assy (B-3)
and connect each connector.
18Pin
mb177a
5
20Pin
24Pin
B-3 Bracket
Assy
Use the screw tapping (B-7) to attach the GPS antenna (B-2) as shown in the diagram.
Center air outlet panels
mb680
14 For vehicles equipped with a Rockford Fosgate Premium Sound System, apply the sticker (B-10) in the
Harness
position shown in the diagram.
Note The sticker (B-10) cannot be used on ve
B-1 CAN-BOX
hicles not equipped with a Rockford Fos
Connect the corresponding connectors to the har
gate Premium Sound System.
ness (B-6) and audio navi system (A-1).
B-6
mb676
B-2 ANTENNA
ASSY
Clip
10
B-7
Screw Tapping
5mm
(B-10)Sticker
mb672
Connect the harness (B-6).
Connect the GPS antenna
(GPS antenna connector) (B-2)
FM/AM antenna plug (vehicle side)to the audio navi system (A-1).
15 Refer to Option coding( A-5 ) and set the vehicle settings to navigation-equipped vehicle.
mb677