SuperSport™ Club - Fitness Equipment

SuperSport™ Club
Fold-Away™
OWNER’S MANUAL
Super Gym’s FitnessBlowout.com
2210 S. Sepulveda Blvd.
Los Angeles, CA 90064
Phone: 800-FIT-4-LESS
or 800-348-4537
Fax: 310-235-2008
CONGRATULATIONS
Congratulations for selecting Super Gym’s CardioZone as your primary source of fitness.
CardioZone treadmills offer many exercise programs that benefit users of all levels and ages. The
treadmill is designed to make your workouts more effective and enjoyable.
Please read this manual carefully before using your CardioZone SuperSport™ Club. This will allow
you to get a full understanding of all the features that CardioZone treadmills provide. If you have
any questions or concerns, please contact Super Gym’s FitnessBlowout.com.
For service, please visit http://www.fitnessblowout.com/service
Register your warranty at http://www.fitnessblowout.com/warranty
Super Gym’s FitnessBlowout.com
2210 S. Sepulveda Blvd.
Los Angeles, CA 90064
Phone: 800-FIT-4-LESS
or 800-348-4537
Fax: 310-235-2008
1
2
TABLE OF CONTENTS
SECTION
PAGE
1. OVERVIEW DRAWING.......................................................................................... 4
2. IMPORTANT SAFETY INSTRUCTIONS .............................................................. 5
3. GROUNDING INSTRUCTIONS ............................................................................ 6
4. MOTORIZED TREADMILL PRE-ASSEMBLY..................................................... 7
5. ASSEMBLY STEPS ................................................................................................. 8
6. CAUTIONS .............................................................................................................. 11
7. MAINTENANCE ..................................................................................................... 12
8. COMPUTER INSTRUCTION ................................................................................. 13
9. EXPLODED VIEW .................................................................................................. 19
10. TROUBLESHOOTING............................................................................................ 21
11. WARRANTY ............................................................................................................ 23
3
OVERVIEW DRAWING
4
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed,
including the followings:
Read all instructions before using the treadmill.
DANGER – To reduce the risk of electric shock:
1.
Always unplug this appliance from the electrical outlet immediately after using and
before cleaning.
WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:
1.
An appliance should never be left unattended when plugged in. Unplug
when not in use, and before putting on or taking off parts.
from
outlet
2.
Close supervision is necessary when this appliance is used by, on, or near children,
invalids, or disabled persons.
3.
Use this appliance only for its intended use as described in this manual. The
manufacturer does not recommend attachments onto the appliance.
4.
Never operate this appliance if it has a damaged cord or plug, if it is not working
properly, if it has been dropped or damaged, or dropped into water. Return
the
appliance to a service center for examination and repair.
5.
Do not carry this appliance by supply cord or use cord as a handle.
6.
Keep the cord away from heated surfaces.
7.
Never operate the appliance with the air openings blocked.
free of lint, hair, and the like.
8.
Never drop or insert any object into any opening.
9.
Do not use outdoors.
Keep the air openings
10. Do not operate where aerosol (spray) products are being used or where oxygen is
being administered.
11. To disconnect, turn all controls to the off position, than remove plug from outlet.
12. Connect this appliance to a properly grounded outlet only.
Base on content of product. If treadmill has elevation function, it needs to consider the
following issues:
13. If the treadmill is foldable, when user finishes using the treadmill, the elevation needs
to be back to original position.
14. When user is using the treadmill, it cannot be folded at the same time.
15. The appliance is intended for household use on.
5
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This product must be grounded. If malfunction or breakdown occurs, grounding provides a path of
least resistance for electric current to reduce the risk of electric shock.This product is equipped with
a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged
into an appropriate outlet that is properly installed and grounded in accordance with all local codes
and ordinances.
DANGER – Improper connection of the equipment-grounding conductor can result in a risk
of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether
the product is product is properly grounded. Do not modify the plug provided with the product - if it
will not fit the outlet; have a proper outlet installed by a qualified electrician.
This product is for use on a nominal 110~120volt circuit and has a grounding plug that looks like
the plug illustrated in the figure. Make sure that the product is connected to an outlet having the
same configuration as the plug. No adapter should be used with this product.
Figure
Grounding methods
GROUNDED
OUTLET
GROUNDED PIN
6
MOTORIZED TREADMILL PRE-ASSEMBLY
Handrail control button and heart rate strap are optional items in the package
1.Heart rate can be measured in this treadmill. Attach strap to chest during exercise, the heart rate value will
display on the PULSE window.
2. Except using the control button on the console, the control button on the handrail can also be used to
adjust speed and elevation. The control button on the left handrail is for elevation while the right handrail
button is for speed adjustment.
3. Under START/READY condition, if you did not hold grip pulse sensor, then PULSE window will display HP,
when you hole the both sides of grip pulse sensor, you will see the PULSE window display the heart rate values.
ITEM
Description
Qty
A
B
C
D
E
F
G
H
I
J
K
L
Computer set
Frame
Left Upright
Right Upright
Left Side Cover
Right Side Cover
Left handrail
Right handrail
Left handrail cover
Right handrail cover
Bottle holder
Bottle
1
1
1
1
1
1
1
1
1
1
1
1
ITEM
Description
Qty
a
Bolt M8xP1.25x15
10
b
Bolt M5xP0.8x10
4
c
Bolt M8xP1.25x60
4
d
Bolt ψ5x25
2
e
Allen Wrench
5mm
1
f
Allen Wrench
6mm
1
g
SILICON
1
h
Safety Key/Clip
1
i
Power Cord
1
7
ASSEMBLY STEPS
Two people are requested for all assembly steps
(Please note: please follow each step of the assembly
instruction.)
1. First tighten the bottom control wire to the plastic
wire protection sleeve by pulling the guide wire
inside the right upright tube (D). And position it
to the side round hole in the right upright tube,
then insert the upright tubes (C, D) into the two
locations (as the direction arrows shown in the
drawing) on the frame. Secure them with bolts (a)
and wrench provided.
(P.S. In order to prevent it from danger, two persons
are required to assemble the product. Please don't
assemble it alone.)
(P.S. Please be aware that one person must hold the
upright tubes during the assembly process, just in
case, if the tubes fall.)
2. Press the left and right covers (E and F) into
position and secure them with 4 (b) bolts as
shown.
8
3.Computer assembly:
Please connect the control wires between handrails
(L&R) and computer. Then, put handrail (G and H)
according to arrow's direction into the computer (A)
(Ps1. When assembly, make sure that the holes of left,
right handrails are in alignment.)
(Ps2. If treadmill has handrail switches function, please
be aware to assemble, left side of handrail switch is for
incline. Right side of handrail switch is for the speed.)
4. First put the computer on the upper side of frame
which just finished assembly from previous step,
also connect control wire (upper) attached in
computer with control wire (bottom) attached on
treadmill, after finished, then have the control
wire through the upright, then use bolt (c) to
screw tightly according to the drawing on the
right.
(Ps1. To avoid to press the control wire of
handrail)
(Ps2. In order to prevent it from danger, two
people are required to assemble the product.
Please don’t assemble it alone)
9
5. Then, press left screw cover and right screw cover
(I and J) into place and secure them with 2 (d)
screws.
6. Finally secure water holder (K) on computer
console, then the assembly is completed.
10
CAUTIONS
Note: The cylinder contains high pressure; please avoid
contact with any objects.
Note: If the cylinder were damaged, the frame would
not be stable and may cause serious danger during
folding up process.
This treadmill have the foldable mechanism for storage,
when storage must stop all movement (include treadmill
belt stop, take off the power cord), then pull out the
Pop-Pin according to arrow’s direction, then lift up the
treadmill, until POP=Pin click the hole, then can take the
had off, opposite, if want to use treadmill, just pull out the
POP-Pin as the arrow’s direction, then put the treadmill
slowly on the floor, until POP-Pin click to the position.
(Ps.1.Prevent from causing dangerous is careful if the kids
are around. If want to move the treadmill, must fold the
treadmill, let hands hold on rear adjust box, then make the
treadmill incline until the roller can be moved smoothly,
then can move the treadmill.)
(Ps.2.In order to avoid of dangerous, DO NOT move the
treadmill on uneven ground.)
11
MAINTENCE
1. If the Walking Belt tracks off center to the right or left of
the deck, first turn the power off.
Then use a 6mm
wrench (f) to tighten the rear roller bolt on the side of the
treadmill toward which the belt is moving.
For
example, if the belt moves to the left and the deck
becomes exposed on the right, tighten the bolt on the left
side of the frame. Tighten about 1/4 of turn (clockwise).
If the belt does not move back to the center of the
treadmill, make another adjustment to the same bolt.
Once the Walking Belt has been adjusted closer to the
center,
the
treadmill
can
be
started
again.
(Ps.1.This action is very important, please follow the
above steps.)
(Ps.2. The potion of running belt might not stay precisely
in the center with slightly moving the left or right side,
and the situation varies with how end-users use and
weight of end-users. When end-user use properly, the
belt won’t scotch side rails. )
2. It is recommended that the deck be lubricated every
6~12 months according to the frequency of usage. First,
use wrench to loosen the bolts in the end caps. Pull up
the Walking Belt, dispense the lubricant on the deck, and
spread evenly.
After lubricating the deck, center the
belt, and check the belt tension. Adjust the belt as
mentioned in step 1.
(Ps. If the belt happens to slip, follow the above steps
and lubricate the running deck.)
SUGGESTED PREVENTIVE MAINTENANCE SCHEDULE IN
ACCORDANCE WITH THE AVERAGE RUNNING SPEED
Measurement
Speed
Interval
6KM/hr below
1 year
Metric
6~12KM/hr
6 months
12KM/hr above
3 moths
4mile/hr below
1 year
English
4~8mile/hr
6 months
8mile/hr above
3 moths
Note: This preventive maintenance schedule is
only meant for home use. It is suggested to
maintain the unit every month for
commercial use.
12
Computer Instruction
I. General operation
1. Turn on the On-off switch.
2. Put the safety key into the recess of the console. The beeper will make an alerting sound,
meanwhile the dot matrix LED light will be blinking, program light will blink to lead user;
this means the treadmill is ready to start. At the ready-start stage, hold the heart rate
sensor to measure your heart rate
** The chart below provides different heart rate due to age and amount of exercise：
HEART BEATS/MIN
170
150
120
20
166
146
117
25
162
143
114
30
OVER
MIDDLE
LOW
157
137
111
35
153
135
108
149
131
105
40
45
145
128
102
50
140
124
99
55
136
120
96
60
132
116
93
65
(Age)
3. Press
to begin, MANUAL will blink, the treadmill starts with a velocity of 0.5MPH.
While the belt is running, press
、
to accelerate or decelerate the speed of the belt, (or
press
、
、
、
、
to choose the speed you want) or press
inclination angle greater or smaller. (or press
you want.) Press
、 、 、 、 、
to stop all motions. (Press
13
、
to adjust the
to choose the angle
once, Time Window will display
STOP, to pause motions of the treadmill and values on the computer console and will
remain paused for 60 seconds, after 60 seconds all values will return to zero including the
inclination which means its back to the ready-start stage. If press
twice, and
for 3 second for the second attempt, the computer will automatically RESET
hold
itself and return to the ready-start motion.)
** Speed Range：0.5~12MPH，each level raise 0.1 MPH.
Angle Range：0~15 %，each level raise 1 %
4. Except using the control button on the console, the control button on the handrail can also be
used to adjust speed and elevation. The control botton on the left handrail is for elevation
while the right handrail botton is for speed adjustment.
5.
II.
At the ready-start condition, press
to select other functions:
** If the safety key is not inserted into the recess of the console, then all the windows will
display *-----*, this means the treadmill is not ready to start.
**While in motion, if the safety key fell off from the recess console, an alarm will be turned
on, and then all motions will be stopped. Reenter the key into the key slot, all values
will return to original PROGRAM setting
**At ready state, if the heart rate sensor is not being held by 2 hands, then the PULSE
window will display “HP”. If the heart rate sensor is being held, then the heart-beeping
rate will be shown on the display
MODE function key:
1.
At the ready-start condition, press
function key, MANUAL LED will be blinking,
、
or
、
to change to MANUAL、P1~P5 or HRP LED.
press
2. MANUAL Function：
2.1 While MANUAL light is blinking; press
, MANUAL will stop blink, it will
continue bright, TIME light will be blinking, now, you can adjust time.
2.2 Press
, the motor will operate directly according to installed value 0.5MPH, at the
、
、 to adjust the treadmill inclination up/down、speed
time, press
or
increase/decrease.
2.3 Dot matrix LED will arrange in a circle according to the running distances. 40 LED make
up a circle, mean that 0.25mil in total.
3. P1~P5 Program Control Function (Each PROGRAM control has 12 grades.)
3.1. When MANUAL LED is blinking, press
、
or
、
to select the P1~P5
to confirm. After enter the program control function,
LED light you want, press
the indicator light will keep blinking.
3.2. At this time, L1 LED will be blinking. This function is used to select violent degree of
exercise. (L1~L5) Pres
、
or
、 to select the grade you want. Press
to
confirm, the LED will keep bright.
3.3. When the grade option confirmation is done, the TIME LED indicator light will be
blinking, press
、
or
、
to adjust time, after setting up, press
to start the
treadmill, or press
to reenter the PROGRAM selection mode.
**Pre-set Time：25(min) ; Time Range：5~99(min).
3.4. Press
, the motor will operate directly according to installed value, the treadmill
program is installed with 12 grades each of speed and inclination, the changing method
adapts 12 circulation value, the first degree time setting is 2 minutes, after that each
14
degree for time setting is 1 minute. When time is up, the speed and inclination value
will be changed directly. (When operating, press
、
or
、
can control the
speed increase/decrease and the inclination angle bigger or smaller directly as your
wish.)
3.5. In P1~P5 function setting, if press
, the treadmill will start according to program
settings. Those didn’t set up any value; the system will adapt the installed (pre-set)
value automatically. Press
、
or
、
can change PROGRAM setting, but
entering next grade will return to the original PROGRAM setting.
3.6. In each PROGRAM, before L1~L5 begin, they all have 1 minute for warm up. It will
start with each LEVEL initial velocity
3.7. P1 and P2 both has its definition as below.：
P1 5K RUN：The pre-set distance in this program is 5000m（3.1mil）. It will be
finished, after you run 5000m（3.1mil）, and the treadmill will stop.
Under this mode, jog is the main part purpose.
P2 9 HOLE：The pre-set distance in this program is 3500m（2.17mil）. It will be
finished, after you run 3500m（2.17mil）, and the treadmill will stop.
Under this mode, it imitated golf course, and the difficulty is basing on
the changes of upgrade or downgrade.
3.8. About pre-set value of P1~P5, refer to following PROGRAM figure：
15
P4 FAT BURN
P3 CARDIO
P5 HILL INTERVALS
16
4.
HRP function：(This function must be operated with heart rate strap.)
4.1 The purpose of this program is self-training based on heart rate. During the training, when
heart rate of runner achieves the preset heart rate, the speed and elevation are kept within a
certain range for best training effort.
4.2 When MANUAL LED is blinking press
blinking, press
4.3
to confirm.
or
、
until the HRP light is
、
At this time enter the values the program requires.
Supposedly the AGE indicating light is blinking, press
、
or
to adjust
、
your age. Press
to enter next sep.Preset Age： 30Range：13~80, Step is 1
4.4 At this time the PULSE LED is blinking, enter your pulse value. This value is variable
according to your age. Please see the following appendix and choose the value you fit.
You can press
or
to adjust pulse value. If you didn’t do any change,
、
, and the program will achieve according to the preset value and enter next step.
press
4.5
、
TIME indicating light is blinking, enter the time you want by press
、
or
、
or
directly and start exercising without countdown timer
**Adjustable Time range: 5~99 min
** Following provide the HRC option age and HRC pre-set list：
BPM
BPM
Age
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
BPM
Age
H
Pre-set
L
197
196
195
194
193
192
191
190
189
188
187
186
185
184
183
182
181
181
124
124
123
122
122
121
121
120
119
119
118
118
117
116
116
115
115
114
124
124
123
122
122
121
121
120
119
119
118
118
117
116
116
115
115
114
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
BPM
Age
H
Pre-set
L
180
179
178
177
176
175
174
173
172
171
170
169
168
167
166
165
164
163
113
113
112
112
111
110
110
109
109
108
107
107
106
106
105
104
104
103
113
113
112
112
111
110
110
109
109
108
107
107
106
106
105
104
104
103
17
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
Age
H
Pre-set
L
162
162
161
160
159
158
157
156
155
154
153
152
151
150
149
148
147
146
103
102
101
101
100
100
99
98
98
97
97
96
95
95
94
94
93
92
103
102
101
101
100
100
99
98
98
97
97
96
95
95
94
94
93
92
67
68
69
70
71
72
73
74
75
76
77
78
79
80
H
Pre-set
L
145
144
143
143
142
141
140
139
138
137
136
135
134
133
92
91
91
90
90
90
90
90
90
90
90
90
90
90
92
91
91
90
89
89
88
88
87
86
86
85
85
84
,
III、Body Fat Measurement
1. Press
to start the function.
2. Please enter your 『Age』,『Sex』,『Height』and『Weight』
Press
or
、
、
to change the value.
After entering each value, press
to confirm, and continue next value setting.
3. While selecting the function, the program requires you to enter the below values:
*Age：Preset 30
Range：13~80
Step = 1
Press
to confirm, and go to next setup.
*Sex：Preset 1 (Male)
Range :1(Male)、0(Female)
Press
、
or
、
to switch ♂(Male)、♀(Female)
Press
to confirm, and go to next setup.
*Height：Preset 5’7”
Range：3’11” ~6’7”
Step =1”
Press
to confirm, and go to next setup.
*Weight：Preset 150LBS
Step =2 LBS
Press
to confirm.
4. After selecting the above values, hold the heart rate sensor for about 30 seconds.
After 30 seconds, the display will show the “body fat” value.
5. When setting, under the setting items, each items LED indicator light is flashing and display
the pre-set value directly, also can change the pre-set values
**The below is a list indicating degrees of fat, it is divided into male and female sections.
Indicator
Sex
1(Male)
0.0~10.0
10.1~25.0
25.1~30.0
30.1~35.0
35.1~
0(Female)
0.0~20.0
20.1~35.0
35.1~40.0
40.1~45.0
45.1~
18
EXPLODED VIEW
19
PARTS LIST – CardioZone SuperSport™ Club
Description
Item
1
1-1
2
4
4.1
5
6
7
7-1
8
9
10
11
11-1
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
Computer Console
Water Holder Tray
Bolt
K-299
Handler Upper Cover (L)
P-1102L
Handler Upper Cover (R)
P-1102R
Handler plate
NO.2405
Bolt
ψ4x10
Handler Bottom Cover (L)
P-1099L
Handler Bottom Cover (R)
P-1099R
Handler
Cap
ψ1-1/2"x1.5t
PVC Sponge
Upright (L)
Upright (R)
Support Base
Active wheels
P-1312
Spring Washer
M8
Spacer
T*1316
Plastic Washer
P-1057
Axile
T*1318
Incline Base
Wheels
P-320
Bolt
M8xP1.25x15
Bolt
M10xP1.5x12(Blue Locktite)
Double D Washer
NO.2737
Bolt
M10xP1.5x35(Blue Locktite)
Bot
M8xP1.25x40
Bolt
ψ5x25
Plate (L)
NO.2392-L
Plate (R)
NO.2392-R
Base
Bolt
K-288
Nut
M10xP1.5
Post
T*1026
Bolt
M8xP1.25x35
Deck
NO.2393
Nut
M8xP1.25
Spring
S-077
Spring Spacer
P-1058
Safety key/ Clip
Cylinder
CY-004
Water Bottle
Tx771
Bolt
M5xP0.8x10
Cover (L)
P-1103L
Cover (R)
P-1103R
Motor Bottom Cover
P-1314
Description
Qty Item
1
1
4
1
1
2
2
1
1
2
2
2
1
1
1
4
6
4
6
2
1
2
8
8
8
4
1
2
1
1
1
4
5
1
1
1
15
1
1
1
2
1
10
1
1
1
20
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
Sensor (Round)
Bolt
M5xP0.8x12
Wire Button
UC-1
Bolt
M4xP0.7x15
Bolt
M8xP1.25x40
Belly Pan
P-1388
Bolt
M8xP1.25x50(25m
Cushion
P-1301
Bolt
M4xP0.7x10
Plastic
P-1034
Bolt
ψ4x12
Bolt
M8xP1.25x55
Washer
ψ8xψ12x1.5t
Bolt
M8xP1.25x45
Bolt
M8xP1.25
Rear Adjust Box (L)
P-1054L
Rear Adjust Box (R)
P-1054R
Bolt
M4xP0.7x20
Upper Cover
P-1313
Front Roller
Running Belt
Side Rail
P-1053C
Rear Roller Set
Bolt
M8xP1.25x35
Sponge
20x100x1.5t
Running Deck
Power Cord
Control Wire (Bottom)
Wire Button
UC-0
Side Cover Plastic
P-1319
Extention wire (Green)
14AWGx120mmx1T1R
Extention wire (White)
14AWGx90mmx2T
Extention wire (Black)
14AWGx90mmx2T
Extention wire (White)
14AWGx170mmx2T
Extention wire (Black)
14AWGx170mmx2T
Allen Wrench
6mm（80mmx80mm）
Allen Wrench
Wheels
5mm（80mmx80mm）
P-1145
Bolt
M4xP0.7x16
Bolt
M8xP1.25x25
Foot Pad
P-1151
Bolt
ψ4x20
Metal Powder
T*1312
Sensor plate
P-1152
Metal Powder
T*1312A
Bolt (Steel)
M5xP0.8x8
Qty
1
4
2
1
2
1
2
6
8
8
32
3
3
1
2
1
1
2
1
1
1
2
1
6
6
1
1
1
2
2
1
2
1
1
1
1
1
2
4
2
4
8
8
1
2
3
TROUBLESHOOTING
ERROR MESSAGE
PROBABLE CAUSES
SOLUTION
- Loss of Feedback
Speed Sensor disconnected
Check Speed
Sensor Connection
- Running Deck
Running Deck not lubricated
Check R-Deck oil
Speed Sensor misaligned
Check Sensor position
Speed Sensor Faulty
Replace S-Sensor
Loose Display Cable
Check Display
Cable connection
Faulty MCB
(D2 LED on)
Replace MCB
Drive Motor disconnected
Check D-Motor connection
Drive Motor Faulty
Replace D-Motor
- Body Fat Data Incomplete
Heart Rate not detected
Hold Heart Rate Grip Properly
- Loss of Data
Faulty Receiver in Display
Replace Heart Rate Receiver
Faulty Control Board in
Display
Replace Heart Rate Control
Board
E1
E4
21
ERROR MESSAGE
PROBABLE CAUSES
SOLUTION
- Safety Key Off
Safety Key Faulty
Check Safety Key or Switch
- Elevation Motor
Elevation Motor not moving
Check Elevation Motor
connection
- Stalled Elevation
Elevation Motor screw binding
Clean screw and lubricate
Elevation Motor out of Range
Check Zero Position of
E-Motor
E-Motor Potentiometer
Replace Elevation Motor
- Elevation Motor
Elevation Motor out of Range
Replace Elevation Motor
Display Doesn’t Lit Up
On/Off switch
Check if unit is turned on
Insufficient Power Source
Plug unit in a dedicated 120V,
20Amp Outlet
Line Cord Damaged
Replace Line Cord
Fuse
Check Fuse on MCB
E6
E7
22
WARRANTY
USA Warranty
Warranties may vary in other countries.
Please register your warranty at http://www.fitnessblowout.com/warranty
SUPER GYM’S FITNESSBLOWOUT.COM extends the following exclusive, limited warranty of CARDIOZONE,
which shall apply only to the use of the device in the home, for residential, non-commercial purposes only unless
otherwise stated in writing. Any other use of the device shall void this warranty.
FRAME – LifeTime
Super Gym’s FitnessBlowout.com warrants the Frame against defects in workmanship and materials for Lifetime, so
long as it remains in the possession of the original owner.
DRIVE MOTOR – LifeTime
Super Gym’s FitnessBlowout.com warrants the Drive Motor against defects in workmanship and materials for Lifetime
from the date of original purchase, so long as the device remains in the possession of the original owner.
ELECTRONICS & PARTS – 2 Years
Super Gym’s FitnessBlowout.com warrants the Electronic components and all original parts (other than the Motor)
against defects in workmanship and materials for a period of two years from the date of original purchase, so long as the
device remains in the possession of the original owner.
LABOR – 1 Year
Super Gym’s FitnessBlowout.com shall cover the labor cost for the repair of the device for a period of one year from
the date of original purchase, so long as the device remains in the possession of the original owner.
EXCLUSIVE REMEDY
The exclusive remedy for any of the above warranties shall be repair or replacement of defective parts, or the supply of
labor to cure any defect, provided that labor shall be limited to one year. All labor shall be supplied by the local retailer
and the product must be located within the retailer’s service area. Products located outside the retailer’s service area will
not be covered by the labor warranty.
23
EXCLUSIONS AND LIMITATIONS
This warranty applies only to the original owner and is not transferable. This warranty is expressly limited to the repair
or replacement of a defective Frame, Electronic component, or defective part and is the sole remedy of the warranty.
The warranty does not cover normal wear
Super Gym’s FitnessBlowout.com expressly disclaims all other warranties, express or implied, including but not limited
to all warranties of fitness for a particular purpose or of merchantability. This warranty gives you specific legal rights
and your rights may vary from state to state.
WARRANTY REGISTRATION
Register your warranty online at http://www.fitnessblowout.com
24