Portable Emergency Repeater Programming Cheat

Wrightwood Communications Group
Non-profit 501(c)(3)
P.O. Box 3100
Wrightwood CA 92397
(760) 249-5248 Fax (760) 249-3538
[email protected]
KW6WW Emergency Repeater Odd Offset Programming
The frequency pair is a TASMA emergency split and not the normal
600 KHz offset. If you haven’t already programmed it, the chances
are you won’t be able to do it during an emergency.
The two repeaters are not operating at all times and activated from
time to time for testing of radio programming, exercises and during
emergencies when needed.
Emergency Repeater #1
RX of 144.930
TX of 147.585 and Tone of 100.0.
Emergency Repeater #2
RX of 144.930
TX of 147.585 and Tone of 91.5
Cheat sheets for the odd offset programming is included for:
Vertex VX150-VX170
Kenwood TM-V71A
Kenwood TH-F6
Yaesu FT 7900
Wouxun KG-UVD1P
\fXj~l50
\M4fvr w
vomciA
IS MtEP
CTCJLS
ro
IT
aa
vfo ) ? ?a
PR TO "TKj
-ate PTT
T>t€
cape"^ Key
^ (ft)
lo.Q
PL-
If 1
L
AM>
5 S
TH%
icex P^ i
TTT5 DIAL, ro
,,p
P.IAL TG
AS w
.MVP
To
AIR
TV^X f TJ
DIM. n- nix pss^tep
UUonJCs Fa/L
l/X I7o
t
A/VO TV/W
Kenwood TM-V71A (Mobile) 144/430 MHz
Programming / VFO entry
Fast Method
Save VFO [previous step} to
Memory
Alt method
Copy closest Memory Freq
into VFO Mode.
Direct Freq Entry – push Prg
key on Mic for Enter Mode.
(Call A) in this case
[F] >[VFO]>Dial Tuning
Control {push knob to
access MHz mode}
[F] > Dial to mem
ch.>[MR] {prog ch has
“s” with data; and
“” without data}
Type numbers from Key
pad on Mic
STORING ODD SPLIT REPEATER – Steps –
Kenwood TM-V71A
1) Store the Rcv freq in memory as
2) enter [VFO]
normal.
3) Select Tx freq
4) select any other
setting, tone on/off,
etc.
5) Press [F]
6) select same
channel as in step 1.
7) press [PTT] + [MR] stores in mem
Display shows “+”
and “-“
Kenwood_TH_F6_TMtmV71cheatsh.pdf
September 2010
Kenwood TH-F6 - handheld
Action
Keypad
Select Band
[A/B]
Copy MR into VFO
When in memory Press [F] , [VFO]
Use top dial to select Freq Dial freq
Save Freq into Memory
[F] > dial to channel.( “” is empty) > [MR] to save
Select offset
[F] > [REV], (cycle thru “+”,” –“, “ “off)
PL/CT select
[F] > [Tone] T/CT/DCS/ off > use dial freq
Select PL or CT
Tone toggle
Select odd offset
Menu > dial 6 > menu >dial offset
Freq entry with key pad [VFO] > [Ent]
Toggle between freq/Alpha
[Mn-f]
STORING ODD SPILT REPEATER FREQ - steps
¬Press [VFO]
- select Rcv freq.[use tuning knob or s /t ]
¯ Press [F] A memory channel number
® Also select tone
function or CTSS/DCS if
appears and blinks. “” indicates empty,
desired.
“” indicates channel contains data.
± Press [MR] to store data to the channel.
° Select mem channel
² (in VFO) Select TX Freq ³ Press [F]
µ Press [PTT]+[MR]
´ Select the same Mem
the TX freq is stored
channel as step 4 above.
Press [MR] to access mem channels
An odd-split mem ch appears “+” and “-“ on display. Press [REV] to confirm TX
freq. freq step size must be same for both when revising only TX freq.
Kenwood_TH_F6_TMtmV71cheatsh.pdf
September 2010
Model Wouxun KG-UVD1P
June 18, 2012
KG-UVD1P Menu
Selections.
MENU #
1
2
3
FUNCTION
Frequency Step
Squelch Level
Battery Save
4
5
Transmit Power
TXP
Transmit Voice Prompt ROGER
6
Time Out Timer
TOT
High (5 or 4 Watts, Low 1 Watt)
On or Off
15 seconds and Up (Must have voice # 9 on in order to be
useful)
7
VOX
1 to 10 and Off
8
Vox
Wide / Narrow
Bandwidth
WN
25 or 12.5 KHz (works with transmit output only)
9
10
11
12
13
Voice Toggle
Time Out Alert
Beep
Power On Message
Lock Transmit
VOICE
TOA
BEEP
PONMSG
BCL
Chinese , English and Off
1 to 10 seconds and Off
On or Off
Off - Battery Voltage - Welcome
On or Off
14
15
16
17
18
Auto Lock
Receive CTCSS Tone
Transmit CTCSS Tone
Receive DCS
Transmit DCS
AUTOLK
R-CTC
T-CTC
R-DCS
T-DCS
On or Off
Set RX Tone Frequency
Set TX Tone Frequency
Set RX DCS Value
Set TX DCS Value
19
Scan Mode
SC-REV
20
Set Side Key
Freq Mode / Channel
Mode Display
(Auto) Backlight
Offset Frequency
PF-1
Shift
Stopwatch
Channel Name Edit
Enter Memory Channel
Deleting Memory
Channel
Radio Reset
CTCSS / DCS
Frequency Scan
SFT-D
SECOND
CHNAME
MEM-CH
- , + and Off
On and Off
A to Z (caps only and No spaces) and 0 to 9
1 to 128
DEL-CH
1 to 128
RESET
Menu or All
SCNCD
CTCSS or DCS
21
22
23
24
25
26
27
28
29
30
DISPLAY
STEP
SQ - LE
SAVE
SELECTIONS
5 , 6.25 , 10 , 12.5 , 25 , 50 , 100 KHz
0 to 9 (4 was used with test sample, 5 is default)
On or Off
TO-Time (5 sec), CO-Carrier (3 sec delay), SE-Carrier
(instant)
Scan, Lamp, FM Radio, SOS
CH-MDF Channel, Freq + Chan # , Channel Name
ABR
On or Off (no "on" full time is provided)
OFFSET 0 to 69.950 MHz
http://groups.yahoo.com/group/WOUXUN_KG-UVD1P
Model Wouxun KG-UVD1P
These instructions are with the MENU 9 (voice) is set to off
1. Turn on the radio.
 If in channel mode, press [MENU], then TDR, to switch to Frequency Mode.
2. Press 6-DIGIT FREQ (your Rx Freq) (e.g., 1,4,4,9,3,0).
 If using Tx tone: [MENU] 1,6, [MENU], scroll Tone freq, [MENU]
 If using Rx tone: [MENU] 1,5, [MENU], scoll tone freq, [MENU]
3. Press [MENU], 2, 7, [MENU]. (QUICKLY THEN SELECT MEMORY NEXT STEP)
4. Type 3-DIGIT memory (e.g., 0, 9, 9), [MENU].
(Or scroll using right knob to the memory channel, [MENU])
5. Wait a second, or press cancel to exit the menu.
6. Press 6-digit Tx freq (e.g., 1,4,7,5,8,5).
7. Press [MENU], 2, 7, [MENU], Press 3-digit memory as above (0, 9, 9), [MENU].
The odd split is now programmed.
USE TO SCROLL SELECTION
TDR (one band selection)
M ENU FUNCTION
Reverse Tx/Rx freq