mode

Transcription

mode
Setting Guide
Version 1.0
September / 22/ 2014
Table of Contents
1.
2.
3.
4.
5.
Device Descriptions ........................................................................................................... 4
Operation Modes ................................................................................................................ 6
Key Function Description .................................................................................................. 7
LED , Buzzer and Vibration ............................................................................................... 8
Bluetooth Connect Description ........................................................................................ 10
5.1. Specification ......................................................................................................... 10
5.2. Data transfer via Bluetooth Under Batch mode ................................................... 10
5.3. SPP Communication............................................................................................. 11
5.3.1.
SPP Transfer Data format ......................................................................... 11
5.3.2.
Host command.......................................................................................... 12
5.4. HID Communication ............................................................................................ 14
6.
7.
8.
USB connect ..................................................................................................................... 16
6.1. Specification ......................................................................................................... 16
6.2. USB Mass Storage communication...................................................................... 16
6.2.1.
USB data transfer mode ........................................................................... 16
6.2.2.
The Data format of data file ..................................................................... 17
6.3. USB-HID communication .................................................................................... 18
The Suitable use method .................................................................................................. 19
Simple Setting .................................................................................................................. 20
8.1. Batch Mode setting............................................................................................... 20
8.1.1.
Data transfer by USB situation................................................................. 20
8.1.2.
Data transfer by SPP Master mode situation ............................................ 20
8.1.3.
Data transfer by SPP Slave mode situation .............................................. 21
8.2. Real mode setting under HID communication ..................................................... 22
8.3. Real mode setting under SPP communication ..................................................... 22
8.3.1.
Real mode setting under SPP master mode .............................................. 23
8.3.2.
Real mode setting under Spp Slave mode ................................................ 23
8.4.
9.
Hybrid mode setting under SPP communication ................................................. 23
8.4.1.
Hybrid mode setting under SPP Master mode ......................................... 24
8.4.2.
Hybrid mode setting under SPP Slave mode............................................ 24
System Detail Setting ....................................................................................................... 26
9.1. Factory Default Setting ........................................................................................ 26
9.2. The setting Barcode of System............................................................................. 30
9.2.1.
System mode setting................................................................................. 30
9.2.2.
HID Communication Setting .................................................................... 36
Cyclops-II BlueTooth Scanner Configuration Guide
2
9.2.3.
10.
11.
SPP Communication Setting .................................................................... 39
9.2.4.
Batch mode setting ................................................................................... 43
9.2.5.
Barcode Data and Scanner Setting ........................................................... 47
9.2.6.
Alpha-Numerical Setting barcode ............................................................ 69
Appendix 1 ............................................................................................................... 74
Appendix 2 ............................................................................................................... 75
Cyclops-II BlueTooth Scanner Configuration Guide
3
1. Device Descriptions
Scan Window
Bluetooth LED
Scan LED
Power LED
SCAN Key
FUNCTION Key
Battery
Strap Post
USB Port & Reset button
Table - 1
Item
Scan Window
Descriptions
Scanner scans barcode via this window ( DO NOT SCRATCH or
BLOCK )
Power LED
Battery Status
Green light ON: Charging Completed
Green light blinking: Battery Low
Red light ON: Battery Charging in Process
Red light blinking: Charging Failed
Scan LED
Barcode Scanning Result:
Green ON: Barcode decoding success
Red ON: Barcode reading fail (decode time-out error )
Orange blinking: System firmware update in process
Orange ON: System firmware update completed
Bluetooth LED
Bluetooth Communication Status
Blue fast-blinking: Radio Fail, Pairing Started,
Paring Fail, Lost Connection,
Not Connected,
Communication Error
Cyclops-II BlueTooth Scanner Configuration Guide
4
Scan Key
Blue slow-blinking: Successful Connection
USB Connection Status( Bluetooth Mode )
Blue ON: USB Connected
Blue slow-blinking: Data Transmitting
Press and hold more then 3 seconds: Power On
Press:Barcode Scan
Function Key
According difference mode it will have difference function, Please
reference【3. Key Function Description】。
Battery
AC Adapter for charging
USB Port
Use USB cable for data transfer.
Reset Button
Press the button, The system will be power off
Strap Post
Hand strap use
Cyclops-II BlueTooth Scanner Configuration Guide
5
2. Operation Mode
This device have three action mode, the default action mode is real mode.
The mode can be changed by scan setting barcode. But, the customer can not change the
mode If the data file(data.txt)have some records not be send out .
The description of mode, please see the follow table.
Table - 2
Action Mode
Real Mode
Description




Batch Mode
The scan data will be transferred via Bluetooth connect, and the scan
data will not be transferred and not be saved to data file when the
Bluetooth is disconnect.
HID communication support.
This mode support connection error handshake on SPP.
It need an application to handle the communication handshake and
data receive / send on SPP communication
The scan data will be saved to this device.
You have two methods to get the scan data
 Bluetooth data transfer:You can send the data via Bluetooth SPP
connection.
 USB transfer:You can transfer the data file via USB cable connect.
You have two methods to delete the data.
 Scan a factory default of setting barcode
 Delete the data file after USB connect
Hybrid Mode
USB-HID
Mode

The scan data will be transferred via Bluetooth connect, and if
Bluetooth disconnect, the scan data will be saved to the data file, after
Bluetooth reconnect, the records of data file will be transfer to host
device via SPP communication. After transfer complete the records on
the data file will be deleted.

You need an application to handle the handshake under SPP
communication.
In this mode, the scan data will be transferred via USB cable to Hos. It will
like a USB scanner. You can change to Bluetooth mode by setting, then the
scan data will be transferred via Bluetooth.
The customer can make a decision, according the customer environment to choice the best
mode.
Cyclops-II BlueTooth Scanner Configuration Guide
6
3. Key Function Description
The follow table descript the motion of the status and key function.
Table – 3
Motion status
Power
Off
Scan
Bath mode
HID
Scan Key
Disconnect SPP
Disconnect
—
—
—
—
—
Bluetooth
+
Function
Key
—
Scan Key
—
data transfer
and wait state
mode
2
Scan
Delete one
—
recode of data
file3
Reset
Button
SPP
Hybrid mode
Power
Key( press On1
more then
3 seconds)
Function
Key
Real mode
—
Send key
4
code
Send
Reconnect
key
Send
Reconnect
Key
code5
code
Reset
6
1
This BTS700 will auto Power off。
Press Scan key and hold more then 3 seconds on the BTS700, it will start on and load the
system configure.
2
When you change it to Bluetooth data transfer mode, BTS700 will wait the host command
from terminal host device include smart phone or tablet device or PC .
3
The scan data will be saved to the file of memory. You can delete the same record on the
data file of memory。 The last record will be deleted first, even you scan the same data on
4
5
6
the different time. It can not delete multi records on the same time.
It can be set enable or disable according you setting.
The software keyboard of iPhone, iPad can be call by press Fn key of BTS700 Via
Bluetooth communication, It can be setting enable/disable different Key code to data
transmit..
It can be setting enable/disable different Key code to data transmit
The power is off after reset
Cyclops-II BlueTooth Scanner Configuration Guide
7
4. LED , Buzzer and Vibration
The following table is description of the LED display and sound on the different issue.
Data collect status
Scan LED
Vibration
User good scan
Green (50ms)
Vibrate 100ms
User bad Scan
(default 5s scan
timeout, 0.5s~25.5s
timeout setting ranged
0.5s)
Configuration good
scan
Red( 300ms)
Configuration bad
scan ( 5 second time
out)
Enter SPP Slave
mode
Enter SPP Master
mode
Red( 300ms)
Green (100ms)
Battery
LED
Sound
Bi
Bi, Bi, Bi
Vibrate
200ms,100ms
(Time interval
between two
vibrations:30ms)
Bi~, Bi
Bu, Bu, Bu
Bu, Bu
Bi, Bi
Enter HID mode
Bu, Bi
Real mode Power Up
Green
Vibrate 300ms
Batch mode Power Up
Red
Vibrate 300ms
Never reset Date and
Time when Power Up
( Only Batch mode )
Orange Flash
On:300 ms
Off:500 ms
3 Times
Green Flash
On:300 ms
Off:500ms
3 Times
Vibrate 300ms
The data file of
memory have data
record When Power
Up
Bluetooth
LED
Bu~,Bu~,Bu~
Vibrate 300ms
Memory Full
Red Flash
On:300 ms
Off:500ms
3 Times
Bu~, Bu~
Delete one record of
data file on the
memory success
It is not found that
press Fn key to delete
one record Under
Batch mode.
The record format of
data file on memory be
changed
Orange
Bi, Bi,
RED
Bu, Bu, Bu
Red( 300ms)
Bu, Bu, Bu
Battery Charging
Red
Cyclops-II BlueTooth Scanner Configuration Guide
8
Battery Charging fail
Red Flash
On:100 ms
Off:100ms
Battery Charging finish
Green
Batter low
Red Flash
On:200 ms
Off:800ms
Bluetooth Paring
Quickly Blue
Flash
wait enter the PIN
code when Bluetooth
paring ( 60 second
time out )
Quickly Blue
Flash
Bi~, Bi~ until
paring ok or
Time out
Bluetooth Paring fail
Quickly Blue
Flash
Quickly Blue
Flash
Slow Blue
Flash
Slow Blue
Flash
Quickly Blue
Flash
Slow Blue
Flash
Bu~,Bu~,Bu~
No Bluetooth connect
Bluetooth connect
success
Vibrate 300ms
Bluetooth connected
Vibrate 300ms
Bluetooth disconnect
or connect fail
Bluetooth reconnected
and data transmit
under batch mode
Bluetooth reconnected
and data transmit
under Hybrid mode
Vibrate 300ms
Red( when the
data
transmitting )
Blue On
USB data transmit
Quick Blue
Flash
Press Fn Key to wait 6
seconds while
Bluetooth reconnect.
Blue On
Firmware Updating
Orange Flash
Firmware Update
finish
Restore Factory
Default
Orange

Bu, Bu
Red( when the
data
transmitting )
USB connected

Bi, Bi
Fast Blinking
Green
Tone :
Bi: short、High tone
Bi~ :Long、High tone
Bu:short、Low tone
Bu~:Long、Low tone
Vibration:
If set vibration on, then enable vibration behave work .
Cyclops-II BlueTooth Scanner Configuration Guide
9
5. Bluetooth Connect Description
5.1. Specification
This BT700 is a wireless interface device, it is follow Bluetooth ver2.1+EDI Class II
specification, include the SPP ( Serial Port Profile ) and HID ( Human Interface Device
Profile) on this device, It must install the same profile on the paring device (ex. iPhone, iPad
or PC ) too for Bluetooth communication.
Specification
Description
Intensity of the
electric wave
Class II
The max distance is 10 M for Bluetooth communication, The
max distance will different according user environment.
Paring
One BTS700 paring with one host device, it can not paring
with more then one host device in the same time.
SPP : It is a serial port communication for SPP slave mode or
Communication
SPP master mode.
HID: It is Human interface communication.
Authentication &
Encryption
Authentication :
Default PIN Code is “0000”, it can be changed by
configure barcode.
Encryption :
The data can be encrypted by Bluetooth communication,
Default is no encryption. It can be enabled / disable by
configure barcode.
※ If BTS700 want connect with the iPhone、iPad of Apple product , the iOS of iphone 、
iPad must lately of version 5.0.
※ If BTS700 want connect with the product of Android smart phone, the OS of Android
must lately of version 4.0.
※ If BTS700 want connect with the BT dongle of PC or NB, the dongle must lately of BT
version 2.0.
5.2. Data transfer via Bluetooth Under Batch
Cyclops-II BlueTooth Scanner Configuration Guide
10
mode
The customer can get the data that be saved under Batch mode by Bluetooth。 The BTS700
must change to Bluetooth data transfer mode, you can reference the「5.3 SPP communication」
Item
Description
How to transfer the Two method of transfer
 Press Key(Scan Key + Fn Key)
data

Scan the “BT data transmission mode change” configuration
barcode (A033A)
5.3. SPP Communication
This section is about the SPP communication
The BTS700 will execute the handshake with host device ( ex. PC, iPhone, iPad or Android
smart phone ) according the setting of BTS700 configuration under SPP communication. So
the customer must install an application on the host device to handle the communication
handshake with BTS700.
The follow table is for customer application reference.
Master mode
BTS700(This Device) send out the paring request to host device.
Please reference “The setting barcode about physical address of
Bluetooth module”
The Bluetooth physical address of Host device only 12 digital.
Slave mode
The host device sent out the paring request to BTS700.
Please reference “The Setting barcode about Device Name of BTS700”
The BT manger application of host device select the BTS700 device name
※ If BTS700 want connect with the BT dongle of PC or NB, the dongle must lately of BT
version 2.0.
5.3.1. SPP Transfer Data format
The Bluetooth communication of SPP mode is simulate the communication of virtual serial
Port, So the host device must install and execute an application to handle the handshake with
BTS700.
Cyclops-II BlueTooth Scanner Configuration Guide
11
The data format of SPP transfer of BTS700 as follow for handshake with Host
application:
[Prefix][Digit][Data][Checksum][Suffix]
Item
Byte
Number
Prefix
1
Digit
2
Value
Description
STX(0x02) The start bit of SPP communication.
The size of Data
Data
The scan data
Check Sum
2
The check sum of Data
Suffix
1
ETX(0x03) The Stop bit of SPP communication.
5.3.2. Host command
Under SPP communication mode, the host device (include Android smart phone, PC ) can
send Host Command to BTS700 to control BTS700, and BTS700 will return the result to host
device after execute the host command.
The data format of Host command as follow:
[Start][Command][Option][End]
Field
Format
Description
Start
!
Host command start
character.
Command
1~8
Command number, that
have 1 to 8 , you can
reference「Host Command
function list table」
Option
YYYMMDDHHMM
For date and time setting
End
CRLF(0x0D0A)
Host command stop
character.
The data format of result that BTS700 execute the host command, the data will be return to
the host device as follow:
Cyclops-II BlueTooth Scanner Configuration Guide
12
[Start][Command][,][Response][End]
Field
Format
Description
Start
RE
The start character of response after
executed host command.
Command
1~8
The response after execute host command
number.
,
Separation
Response
OK
NG
The result after execute host command
YYMMDDHHMM
The date & time of BTS700 for host
command 3
F
M
The battery status of BTS700 for host
command 4
L
End
*******
The record count of data file for host
command 8
CRLF(0x0D0A)
The stop character of response after
executed host command.
The detail of host command and return value, please reference “Host command function
list” table as follow.
The number 5 ~ 8 is used while BTS700 waiting state of “Bluetooth data transmit mode”.
Table : Host Command function list table
No
1
Function
Scan
Host sand
!1<CRLF>
Host Receive
Notes
RE1,OK<CRLF> and
The BTS700 will auto
<data>
scan when the host
RE1,NG<CRLF>
command be executed,
BTS700 will return scan
ok or not and scan data
according SPP transfer
format.
2
Set data and
!2YYYYMMDDHHM
RE2,OK<CRLF>
BTS700 will set date &
Time to
M<CRLF>
RE2,NG<CRLF> ( this
time according this host
is data NG , ex
command.
BTS700
“20130430190000”)
RE,NG<CRLF> ( This
Cyclops-II BlueTooth Scanner Configuration Guide
13
is data format NG , ex
“201304312300”)
3
Read Date of
!3<CRLF>
BTS700
4
Power status
!4<CRLF>
RE3,
BTS700 will return date
YYYYMMDDHHMM
& time according to host
<CRLF>
device.
RE4,F<CRLF>
BTS700 will return
RE4,M<CRLF>
battery status to host
RE4,L< CRLF>
device.
F is Full power
M is Middle power
L is Low power.
5
Send the scan
!5<CRLF>
Send data to host
BTS700 will send all
data file of
[Prefix][Digit] [Time
records of the data.txt on
BTS700
Stamp] [Delimiter]
Memory to host device.
[Data][Checksum][Suffix]
6
Delete the scan
!6<CRLF>
data file of
RE6,OK<CRLF>
BTS700 will delete the
RE6,NG<CRLF>
data.txt file on memory
RE7,OK<CRLF>
BTS700 will change to
RE7,NG<CRLF>
waiting next host
BTS700
7
Communication
!7<CRLF>
Wait status
command status, in this
time BTS700 scan
function will not work.
8
recode count of
!8<CRLF>
RE8, XXXX<CRLF>
data file
BTS700 will return the
record count of data.txt
on memory.
5.4. HID Communication
BTS700 pairing with iPhone, iPad of Apple product or paring with Android, PC by HID
communication, the BTS700 will be keyboard interface of those terminal host device. The
HID mode is default factory mode of BTS700, so the product of Apple can quickly connect
with BTS700 and ease use.
About connect method, please reference the Bluetooth menu of those terminal host device.
The customer can press Fn key to call the software keyboard of iPhone, iPad to show or hide
Cyclops-II BlueTooth Scanner Configuration Guide
14
After BTS700 connect with iPhone, iPad complete.
※ If BTS700 want connect with the iPhone, iPad of Apple product, the iOS of iphone , iPad
must lately of version 5.0.
※ If BTS700 want connect with the product of Android smart phone, the OS of Android
must lately of version 4.0.
※ If BTS700 want connect with the BT dongle of PC or NB, the dongle must lately of BT
version 2.0.
Nots:
If you want the BTS700 be the key board interface of iPhone, iPad, Please set
to“English”mode on the keyboard setting of iPad, iPhone first. If you does not set to
“English”mode, it will display other character on iPhone, iPad after you use BTS700 scan a
barcode data.
Cyclops-II BlueTooth Scanner Configuration Guide
15
6. USB connect
6.1. Specification
This device (BTS700)have a USB port , it will not support charge when you use USB cable
to connect with BTS700 and PC host.
Specification
Communication
Spec
description
USB 2.0 Full speed
 USB Mass Storage support.
 USB-HID communication support.
Cable
Micro USB type B
Connect USB
cable
USB Mass Storage support :
If set Bluetooth (SPP, HID) communication, the BTS700 will
be a USB Mass Storage when USB cable connect between BT700
and Host PC.
USB-HID communication support :
If set USB-HID communication, the BTS700 will like a USB
scanner, then you can scan barcode when the USB cable connect
between BT700 and Host PC.
6.2. USB Mass Storage communication
6.2.1. USB data transfer mode
Under Batch mode, the scan data will be saved into the data.txt file of BTS700 memory.
User can obtain data.txt file that stored in memory of BTS700 with USB thread.
Specification
Transfer
Description
Connect with PC:
When the BTS700 connect with PC via USB cable, the
USB memory of BTS700 will be a disk of PC.
※Please use the USB cable we offer , or buy to us.
USB Memory
Function
Under Batch mode. The maximum records of data.txt are 8000
records. It will include two files on the memory of BTS700.
Cyclops-II BlueTooth Scanner Configuration Guide
16
Data.txt :Under batch mode, the scan data will be saved to
this file, if user use USB cable to connect between
PC and BTS700, the user can read this file or
delete this file.
System.cfg :This is a setting file of BTS700. When this file
be updated, and repower on this device, the system
will be start up and be set according this file.
Notes
Under USB data transfer mode. The follow function will be
limited.
 Bluetooth will be disable ( it will be disconnect ).
 Scan function or other operate will be disable.
6.2.2. The Data format of data file
The recode size is 2048 Bytes on data.txt, the scan data will be saved into this data file. Please
reference the『9.2.4 Batch mode setting』
Data format descript as follow
[Mark][Checksum][Delimiter][Timestamp][Delimiter][Data][Termination]
Item
bytes
Default value
description
Special Mark
+:Added
—:deleted
# : Send out ok
Mark
1
Check sum
4
Check sum
Use 2 digital of ASCII code
Delimiter
1
Separate mark
Time stamp
19
YYYY/MM/DD,hh:mm:ss
Date & time
The separate of data & time,
It is same with Delimiter
field.
Delimiter
1
Separate mark
Data
2020
Scan data,
If data length at the full 2020
Bytes, will fill blank in order
to mend all over 2020bytes
behind data
Record
2
CRLF(0x0D0A)
The termination of every
Cyclops-II BlueTooth Scanner Configuration Guide
17
Termination
record.
6.3. USB-HID communication
Description
Setting
Setting Barcode
Cord
ID
Change to
USB-HID mode
Enable
A114A0
Change to
Bluetooth mode
Enable
A114A1
If set “change to USB-HID mode” , after connect the USB cable , the device like a USB
scanner .
If set “change to Bluetooth mode” , after connect the USB cable , The device will be a USB
mass storage device.
Default is “Bluetooth mode” .
Cyclops-II BlueTooth Scanner Configuration Guide
18
7. The Suitable use method
The user can follow the follow chart to select the best mode for use.
Start
The scan data must be
save to memory and
doesn’t need pairing
with smart phone or PC
via Bluetootn?
The data must be saved
Use Bluetooth
Selsect Batch mode
(reference 8.1 Batch mode setting)
transfer data
by USB
Is it need connect with
Apple product?
Connect with PC or
Android
Transfer data
by Bluetooth
Send pairing
request by
BTS600
Send pairing request
by Host
SPP Master
mode
SPP Slave
mode
Need connected with Apple product
Is it the key board
interface of PC or
Android ? And need
handshake.
Same with Key Board
Real mode under HID connect
(Reference 8.2 the setting of real mode under
HID communication)
Need Handshake
The distance will over
10M( or over the max
distance of BT
communication)?
Never over
the max
distance
of bluetooth
Real Mode under SPP connect
(Reference 8.3 the Setting of Real mode
under SPP communication)
Sometimes will over the max
distance of BT
communication
Hybrid Mode under SPP Connect
(reference 8.4 The setting of Hybrid
mode under Spp communication)
Send pairing
request by
BTS600
Send pairing
request by
Host
SPP Master
Mode
SPP Slave
mode
Send pairing
request by
BTS600
Send pairing
request by
Host
SPP Master
mode
SPP Slave
mode
Cyclops-II BlueTooth Scanner Configuration Guide
19
8. Simple Setting
The use choice the best mode according【7. The Suitable use method】
8.1. Batch Mode setting
If the user want scan the barcode data and be saved into the memory of BTS700, please use
Batch Action mode.
The user can get the record of memory on the BTS700 by different method, according User
setting.
Use USB:If user choice the data transfer mode by USB, please reference【6. USB Connect】
Use Bluetooth:If user choice the data transfer mode by Bluetooth, it will need an application
be install and running on the terminal host like Android smart phone、PC.
please reference【5. Bluetooth Connect Description】
8.1.1. Data transfer by USB situation
Description
Setting
Setting Barcode
Cord
ID
Communication
setting
SPP Slave
mode
A002A
Action mode setting
Batch
mode
A014A2
※ It must setting SPP Slaver mode even the user use USB cable for data transfer.
8.1.2. Data transfer by SPP Master mode situation
Description
Setting
Setting Barcode
Cyclops-II BlueTooth Scanner Configuration Guide
Cord
ID
20
Enter the physical
Imput
B001A
Communication
start
Enter SPP
Master
mode
A001B
Action mode setting
Batch mode
A014A2
Wait host command
under Bluetooth
Start data
transfer by
A033A
address of BT
module
communication
Bluetooth
communic
ation
※please reference 【The Setting barcode about Bluetooth Device name of BTS700】of【9.2.1
System mode Setting】
8.1.3. Data transfer by SPP Slave mode situation
Description
Setting
Communication
Setting
SPP Slave
mode
A002A
Action mode setting
Batch mode
A014A2
Wait host command
under Bluetooth
Start data
transfer by
A033A
communication
Setting Barcode
Cord
ID
Bluetooth
communic
ation
Cyclops-II BlueTooth Scanner Configuration Guide
21
8.2. Real mode setting under HID
communication
The BTS700 pairing with iPhone, iPad of Apple product or pairing with terminal host like
Android smart phone、tablet、PC,and the BTS700 is a keyboard interface of those terminal
host, Please use Real mode under HID communication.
The real mode and HID mode are factory default mode of BTS700, so those host can quickly
pairing with the BTS700.
※ If BTS700 want connect with the iPhone , iPad of Apple product , the iOS of iphone, iPad
must lately of version 5.0.
※ If BTS700 want connect with the smart phone of Android product , the OS of Android
must lately of version 4.0.
※ If BTS700 want connect with the BT dongle of PC or NB, the dongle must lately of BT
version 2.0.
Description
Setting
Setting Barcode
Cord ID
Action mode
setting
Real mode
A014A1
Communication
setting
HID mode
A003A
8.3. Real mode setting under SPP
communication
If the customer want to raise the fault-tolerant of communication, the customer can choice the
real mode and SPP communication mode.
The real mode under SPP communication, it is virtual serial port data communication between
BTS700 and host device. It will make relevant communication protocols by setting to prevent
the data lost.
it will need an application be install and running on the terminal host (like Android smart
Cyclops-II BlueTooth Scanner Configuration Guide
22
phone、PC) . please reference【5. Bluetooth Connect Description】
8.3.1. Real mode setting under SPP master mode
Description
Enter the
physical
address of BT
Setting
Setting Barcode
Cord
ID
Input
B001A
Communication
start
Enter
SPP
Master
mode
A001B
Action mode
setting
Real
mode
A014A1
module
please reference【The Setting barcode about Bluetooth Device name of BTS700】of【9.2.1 System
mode Setting】
8.3.2. Real mode setting under Spp Slave mode
Description
Setting
Setting Barcode
Cord
ID
Communication
setting
SPP
slave
mode
A002A
Action mode
Real
A014A1
setting
mode
8.4. Hybrid mode setting under SPP
Cyclops-II BlueTooth Scanner Configuration Guide
23
communication
Because out of the communication or other reason that the Bluetooth disconnect, in order to
avoid the lost of data, the system will save the scan data into the data file of memory of
BTS700 on the Hybrid mode, so Hybrid mode have higher dependability the Real mode.
Once after the Bluetooth reconnect complete, the system in accordance with storing in the
order in the storing device file, and then pass back and give the end a not host computer.
it will need an application be install and running on the terminal host (like Android smart
phone、PC) . please reference【5. Bluetooth Connect Description】
8.4.1. Hybrid mode setting under SPP Master mode
Description
Setting
Setting Barcode
Cord
ID
Enter the
physical
address of BT
module
Input
B001A
Communication
start
Enter
Spp
Master
mode
A001B
Action mode
setting
Hybrid
mode
A014A3
8.4.2. Hybrid mode setting under SPP Slave mode
Description
Communication
setting
Setting
Setting Barcode
SPP
slave
mode
Cyclops-II BlueTooth Scanner Configuration Guide
Cord
ID
A002A
24
Action mode
Hybrid
setting
mode
Cyclops-II BlueTooth Scanner Configuration Guide
A014A3
25
9. System Detail Setting
9.1. Factory Default Setting
BTS700 Factory Default setting as following tables.
Item
Default
BTS700Action Mode
Real Mode
Communication Mode
HID mode
Device Name
BTS700+last 4 digital of BT MAC Address
Authentication
Disable
Encryption
Disable
PIN Code
“0000”
Power off time out
3 minutes
Beep on Reconnect/Disconnect
Enable
Beep for bad scan
Enable
Sound Volume
High
The default value of Real mode under HID communication as following table.
Item
Default
Function Key code Setting
Return(Enter)
Eject Key※
Delay Time Before Data Transmission
None
Record Termination Character Setting
Setting
Delay Time Between Characters Setting
None
※ Press Fn Key will call soft keyboard of iPad, iPhone display / hide, The Fn key can be
enable/disable by setting.
Under SPP communication the Real mode、Batch mode(Bluetooth data transfer mode)and
Hybrid mode setting as following table。
Item
Default
Master Mode Reconnection Interval Setting
30 seconds
SPP data transfer format
STX[ditital][Data][CheckSum]ETX
ACK/NAK handling of SPP Communication
Enable ACK/NAK handling
Cyclops-II BlueTooth Scanner Configuration Guide
26
※
Setting
※ On the Real mode、Batch mode the “ACK/NAK handling of SPP communication setting”
can be set enable / disable, The Hybrid mode must enable can not change to disable。
The default value of Batch mode as follow table。
Those setting will not influence about Real mode initial.
Item
Default
Time Stamp format
YYYY/MM/DD,hh:mm:ss
Record Termination Character Setting
Termination Character Setting
CRLF
,
Data transfer sequence setting
Unsent data only
Memory Initialization Setting After Data
Disable(The data file will not be deleted)
Transmission
The default value of Scanner as following table
Item
Default
Redundancy Level
Level 1
Security Level
Level 1
All barcode symbologies be disable
All Symbologies return to default
USB-HID /Bluetooth scan mode
Bluetooth scan mode
Inter Character Gap size
Normal inter character Gaps
Character String setting
No Convert
Decode Illumination
Off
Illumination Brightness
Level 5
Picklist mode
Disable Always
Fuzzy 1D Processing
Enable
Decoding AIM pattern
Enable
Codabar, MSI, Discrete 2of5,
Level 4
Interleave 2of5
Inverse Barcode
Regular
Code ID character
None
UPC-A
Enable
UPE-E
Enable
UPE-E1
Disable
EAN-8/JAN-8
Enable
Cyclops-II BlueTooth Scanner Configuration Guide
27
EAN-13 / JAN-13
Enable
Bookland EAN
Disable
Bookland ISBN Format
ISBN-10
UPC/EAN supplemental (Add On)
None
UPC/EAN/JAN supplemental
AIM Code ID format
Combined
UPC-A check digit
Enable
UPC-E check digit
Enable
UPC-E1 check digit
Enable
UPC-A preamble
System
UPC-E preamble
System
UPC-E1 preamble
System
UPC-E convert to UPC-A
Disable
UPC-E1 convert to UPC-A
Disable
EAN-8 convert to EAN-13
Disable
UCC coupon expend code
Disable
Coupon Report
Both Coupon
ISS EAN
Disable
Code 128
Enable
GS1-128
Enable
ISBT-128
Enable
ISBT- connect
Disable
ISBT table check
Enable
Code 39
Enable
Trioptic Code 39
Disable
Code39 convert to Code32
Disable
Code32 prefix
Disable
Code39 check digital verify
Disable
Code39 check digital transfer
Disable
Code39 full ASCII transfer
Disable
Code 93
Disable
Code 11
Disable
Code 11 check digital verify
Disable
Code 11 check digital transfer
Disable
I 2 of 5( Interleave 2 of 5)
Enable
I 2 of 5 check digital verify
Disable
I2 of 5 check digital transfer
Disable
Cyclops-II BlueTooth Scanner Configuration Guide
28
I2 of 5 convert to EAN13
Disable
Discrete 2 of 5
Disable
Chinese 2 of 5
Disable
Matrix 2 of 5
Disable
Matrix 2 of 5 check digital verify
Disable
Matrix 2 of 5 check digital transfer
Disable
Codabar(NW7)
Enable
CLSI Editing
Disable
NOTIS Editing
Disable
MSI
Disable
MSI check digital
One
MSI check digital transfer
Disable
MSI check digital algorithm
MOD 10 /mod 10
GS1 Databar
Enable
GS1 DataBar Limited
Enable
GS1 DataBar Expanded
Enable
GS1 DataBar convert to UPC/EAN
Disable
Micro QR
Enable
Korean 2 of 5
Disable
US Postnet
Disable
US Planet
Disable
Transmit US Postal Check Digit
Transmit US postal Check Digit
UK Postal
Disable
Transmit UK Postal Check Digit
Transmit UK postal Check Digit
Japan Postal
Disable
Australia Post
Disable
Australia Post Format
Auto discriminate
Netherlands KIX code
Disable
USPS 4CB/One Code/Inteligent Mail
Disable
UPS FICS Postal
Disable
GS1 DataBar Limited Security Level
Level 3
Composite CC-C
Disable
Composite CC-A/B
Disable
Composite TLC-39
Disable
UPC Composite Mode
UPC Always Linked
GS1-128 Emulation Mode for
UCC/EAN composite Codes
Disable
Cyclops-II BlueTooth Scanner Configuration Guide
29
PDF 417
Enable
Micro PDF 417
Disable
Code128 Emulation
Disable
Data Matrix
Enable
Data Matrix Inverse
regular
Decode Mirror Images(Data Matrix
only)
Auto
Maxicode
Disable
QR code
Enable
QR Inverse
Regular
Aztec
Enable
Aztec Inverse
Regular
9.2. The setting Barcode of System
Having recorded the establishment bar code that this machine uses as follows, this machine is
dispatched from the factory the setting up value and please reference [9.1 Factory Default setting],
the user can scan the following establishment barcode to change the setting of BTS-600.
9.2.1. System mode setting
The Setting barcode of action mode and Bluetooth communication as follow..
Real mode:
When set up into Batch mode、 Hybrid mode, if still there are records to exist in Data.txt file in the
memory of BTS700, The BTS700 can't switch over into Real mode. It must delete Data.txt file in
memory of BTS700 , then it could change into Real mode
Descriptio
n
Setting
Real Mode
SPP
Master
commu
Setting Barcode
Cyclops-II BlueTooth Scanner Configuration Guide
Cord
ID
A001B
30
nication
A014A1
mode
SPP
Slave
commu
nication
mode
A002A
HID
commu
A014A1
A014A1
nication
mode
A003A
※ Please enter the physical address of BT module of the Host device first, when use SPP
Master communication mode.
Please reference【The Setting barcode about physical address of Bluetooth module】
Batch mode:
When use USB data transfer mode, need to set up SPP Slave communication mode again too。
Descriptio
n
Setting
Setting Barcode
Cord
ID
Batch mode USB
Data
transmis
sion
mode
A002A
Data
transmis
sion
mode
under
SPP
Master
A001B
Cyclops-II BlueTooth Scanner Configuration Guide
A014A2
A014A2
31
commun
ication
mode
Data
transmis
sion
mode
under
SPP
Slave
commun
A002A
A014A2
ication
mode
Hybrid Mode:
Descriptio
n
Setting
Hybrid
SPP
Mode
Master
Communi
cation
mode
Setting Barcode
SPP Slave
communic
ation
mode
Cord
ID
A001B
A014A3
A002A
A014A3
※ Please enter the physical address of BT module of the Host device first, when use SPP
Master communication mode.
Please reference【The Setting barcode about physical address of Bluetooth module】
The Setting barcode about physical address of Bluetooth module
The originally setting barcode for the BTS700 to set up SPP Master mode, then BTS700 can know
Cyclops-II BlueTooth Scanner Configuration Guide
32
and fast connect with host computer.
The physical address of Bluetooth module is 12 digital, you can and only enter 0~9, A~F。
Please use barcode of 【9.2.6 Alpha-Numerical Setting barcode】to enter the physical
address of Bluetooth module。
Description
Enter the
physical address
of BT module
Setting
Setting Barcode
Input
Cord
ID
B001A
The Setting barcode about Device Name of BTS700
The originally setting barcode for Bluetooth communication, that Bluetooth manager of host device
( ex iPhon, iPad, Android smart phone , PC , NB) can search and set pairing connect with BTS700.
Default device name is “BTS700” + last 4 digital of physical address of BT module。
The customer can change the device name of BTS700 use follow setting barcode.
The customer can enter 31 character for device name, you can and only enter 0~9, A~Z, a~z。
Please use barcode of 【9.2.6 Alpha-Numerical Setting barcode】to enter the Device name。
Description
Setting
Setting Barcode
Cord
ID
Device name
setting
Input
B011A
The Setting barcode of Bluetooth Authentication
Description
Authentication
Setting
Setting Barcode
Cord
ID
Enable
A008A
Disable
A008B
Setting
The Setting barcode of Bluetooth Encryption
Cyclops-II BlueTooth Scanner Configuration Guide
33
Description
Setting
Bluetooth
Encryption
setting
Setting Barcode
Cord ID
Enable
A009A
Disable
A009B
The Setting barcode of PIN code
The customer can enter 16 character for PIN code, you can and only enter 0~9, A~Z, a~z。
Please use barcode of 【9.2.6 Alpha-Numerical Setting barcode】to enter the PIN code。
Description
Setting
PIN code setting
Setting Barcode
input
Cord ID
B018A
The Setting barcode of Default PIN Code
The default PIN code is『0000』
Setting
Setting Barcode
Return default PIN code
setting
Cord ID
A017A
The Setting Barcode of Power off time out
Description
Setting
Power off
1
time out
setting.
minutes
Setting Barcode
Cord
ID
A004A1
3
minutes
A004A2
5
minutes
A004A3
Cyclops-II BlueTooth Scanner Configuration Guide
34
10
A004A4
minutes
15
minutes
A004A5
30
minutes
A004A6
45
minutes
A004A7
60
minutes
A004A8
The Setting Barcode of Beep on Reconnect/Disconnect
Description
Setting
Setting Barcode
Cord
ID
The Beep on
reconnect /
disconnect
setting
Enable
A005A
Disable
A005B
The Setting Barcode of Beep for bad scan
Description
Setting
Setting Barcode
The Beep for
bad scan
setting
Enable
A006A
Disable
A006B
Cyclops-II BlueTooth Scanner Configuration Guide
Cord ID
35
The Setting Barcode of Sound volume
Description
The sound
volume
setting
Setting
Setting Barcode
Cord
ID
Off
A010A0
Low
A010A1
Middle
A010A2
High
A010A3
The Setting Barcode of restore Factory Default
Setting
Setting Barcode
Restore Factory default
Cord ID
A012A
setting
wh
9.2.2. HID Communication Setting
This is advanced establishment when Real mode under HID communicates。
HID termination character setting
Description
HID termination
Setting
Setting Barcode
0x28
Cord ID
A021A
character setting
The customer can utilize the following establishment bar codes to set up the ' additional characters '
to the data.
The Key code setting must 2 digital word, and the word can only 0~9, A ~ F.
Cyclops-II BlueTooth Scanner Configuration Guide
36
For example, Scan the barcode Id「B019B」 first, then 「2」
、
「0」
、
「EOC」, The Key Code is 『#』
Please use barcode of 【9.2.6 Alpha-Numerical Setting barcode】to enter the additional
characters。
HID termination character setting
Description
Setting
Setting Barcode
Cord ID
Input
B021A
Input
B021B
additional
characters +Alt
Key setting
Input
B021C
additional
characters
+Ctrl Key
Input
B021D
Normal Key
setting
additional
characters
+Shift Key
setting
setting
The customer can utilize the following establishment bar code to set up the key code beyond '
Eject Key.
The Key code setting must 2 digital word, and the word can only 0~9, A ~ F.
For example, Scan the barcode Id「B019B」 first, then 「2」
、
「0」
、
「EOC」, The Key Code is 『#』
Please use barcode of 【9.2.6 Alpha-Numerical Setting barcode】to enter the Key code。
The setting barcode for transfer key code of Function key under Communication
Description
Setting
Setting Barcode
Transfer key
Disable
code of
function key
under
Enable
communicatio
n setting
Cyclops-II BlueTooth Scanner Configuration Guide
Cord ID
A022A
A022B
37
The setting barcode for the association key code that will be sent while pushing Fn key
Description
Setting
Setting Barcode
Cord ID
Normal
Input
B022A
Input
B022B
Input
B022C
Input
B022D
Function Key
Code Setting
under HID real
mode setting
Function Key
Code + Shift
Key code
Setting under
HID real mode
setting
Function Key
Code + Alt
Key code
Setting under
HID real mode
setting
Function Key
Code + Ctrl
Key code
Setting under
HID real mode
setting
The setting Barcode for delay time before data transmission under BT communication
Description
The delay time
Setting
Setting Barcode
Cord ID
None
A023A0
100 ms
A023A1
before sending
data of each
record can be
set
Cyclops-II BlueTooth Scanner Configuration Guide
38
200 ms
A023A2
300 ms
A023A3
500 ms
A023A4
The setting barcode delay time between characters under BT communication
Description
The delay time
Setting
Setting Barcode
Cord ID
none
A024A0
10 ms
A024A1
20 ms
A024A2
30 ms
A024A3
between
characters of
sending data
can be set.
9.2.3. SPP Communication Setting
This item is advance setting about Real mode, Batch mode(Bluetooth data transfer mode)and
Hybrid mode under SPP communicate.
The setting barcode for SPP Master reconnect time interval
Description
Setting
Setting Barcode
SPP Master
reconnect
time interval
setting
None
A007A0
15 sec
A007A1
Cyclops-II BlueTooth Scanner Configuration Guide
Cord ID
39
30 sec
A007A2
45 sec
A007A3
1 min
A007A4
5 min
A007A5
10 min
A007A6
15 min
A007A7
30 min
A007A8
The transfer data format setting under SPP communication
When set up into Batch mode、 Hybrid mode, if still there are records to exist in Data.txt file in the
memory of BTS700, The follow settings that can not be changed。
The setting barcode of Prefix
The prefix setting must 2 digital word, and the word can only 0~9, A ~ F.
For example, Scan the barcode Id「B019A」 first, then 「3」、「3」、「EOC」, prefix is 『,』
Please use barcode of 【9.2.6 Alpha-Numerical Setting barcode】to enter the Prefix。
Description
Setting
Setting Barcode
Prefix Setting STX(0x02)
Input
Cyclops-II BlueTooth Scanner Configuration Guide
Cord ID
-
B019A
40
Description
Digital
Setting
Description
Checksum
Setting
Setting
Setting Barcode
Cord ID
Digital
exist
A019A
No Digital
A019B
Setting
Setting Barcode
Cord ID
Checksum
exist
A019C
No
Checksum
A019D
The setting barcode of Suffix
The suffix setting must 2 digital word, and the word can only 0~9, A ~ F.
For example, Scan the barcode Id「B019A」 first, then 「3」、「3」、「EOC」, Suffix is 『,』
Please use barcode of 【9.2.6 Alpha-Numerical Setting barcode】to enter the Suffix。
Description
Suffix
Setting
Setting
Setting Barcode
ETX(0x03)
Cord ID
-
Input
B019B
The setting barcode for the handshake of SPP communication
When set up into Batch mode、 Real mode, the customer can setting to enable / disable of
“ACK/NAC of SPP communication”, if Set up into Hybrid mode. It must set enable of
“ACK/NAC of SPP communication”, and it could not change to disable
The setting barcode about ACK/NAK of SPP communication
Description
Setting
Setting Barcode
Cyclops-II BlueTooth Scanner Configuration Guide
Cord ID
41
ACK /NAK
Enable
A020A
of SPP
communicati
on setting
Disable
A020B
The setting barcode for time out of ACK/NAK of SPP communication
Description
Time out of
ACK /NAK
of SPP
communicati
on setting
Setting
Setting Barcode
Cord ID
100 ms
A020C1
200 ms
A020C2
300 ms
A020C3
500 ms
A020C4
1
seconds
A020C5
2
seconds
A020C6
3
seconds
A020C7
5
seconds
A020C8
The Setting barcode for retry cycle of ACK/NAK of SPP communication
Description
Setting
Setting Barcode
Cyclops-II BlueTooth Scanner Configuration Guide
Cord ID
42
Retry cycle of
ACK /NAK
of SPP
communicati
on setting
None
A020D0
1 cycle
A020D1
2 cycles
A020D2
3 cycles
A020D3
The setting barcode for key code send when press Fn Key
The Key code setting must 2 digital word, and the word can only 0~9, A ~ F.
For example, Scan the barcode Id「B019A」 first, then 「3」
、
「3」
、
「EOC」, Key code is 『,』
Please use barcode of 【9.2.6 Alpha-Numerical Setting barcode】to enter the Key code。
Please reference key code on Append 2
Description
Setting
Key code
sent when
press Fn
Key setting
None( D
efault )
Key code
sent when
press Fn Key
setting
Input
Setting Barcode
Cord ID
-
B019C
9.2.4. Batch mode setting
This item is advance setting about Batch mode
The setting barcode for time stamp
Description
Setting
Setting Barcode
Cyclops-II BlueTooth Scanner Configuration Guide
Cord
ID
43
Time stamp
Disable
Setting
(_____#
____)
※_ is
A027A0
space
Enable
(YYYY/
MM/DD#
hh:mm:ss)
A027A1
※ The “#” is a termination character, please reference 「Termination Character Setting」
on the following table
Description
Termination
Setting
Setting Barcode
Cord
ID
;
A028A1
Space
A028A2
Tab
A028A3
Character
Setting
Description
Record
Setting
Setting Barcode
Cord
ID
,
A026A1
Space
A026A2
CR
A026A3
LF
A026A4
Termination
Character
Setting
Cyclops-II BlueTooth Scanner Configuration Guide
44
CRLF
A026A5
Tab
A026A6
The Setting barcode for RTC time clock
Description
Read RTC
date Setting
Setting
Setting Barcode
Start
Cord ID
A034A
Year:please set up 4 digital,Pleas use AD.
Month:please set up 2 digital。
Date:please set up 2 digital。
Please use barcode of 【9.2.6 Alpha-Numerical Setting barcode】to enter the Date。
Description
Set RTC
Setting
Setting Barcode
Input
Cord ID
B035A
date setting
Hour:please set up 2 digital。
Minutes:please set up 2 digital。
Please use barcode of 【9.2.6 Alpha-Numerical Setting barcode】to enter the Time。。
Description
Set RTC
time setting
Setting
Setting Barcode
input
Cord ID
B036A
The Setting Barcode about Bluetooth data transfer
Description
BT Data
Setting
Setting Barcode
Batch mode
Cord
ID
A033A
Transmission
Mode
BT
Cyclops-II BlueTooth Scanner Configuration Guide
45
Change
Data
setting
Transmission
Mode
※ This is same with press Scan + Fn Key
Description
Data transfer
Setting
Setting Barcode
Cord
ID
From top
A038A1
Unsent data
A038A2
sequence
setting
only
Description
Memory
Setting
Setting Barcode
Cord
ID
Enable
A030A
Disable
A030B
Initialization
Setting After
Data
Transmission
Setting
The setting Barcode of Fn key
Description
Func. Key
Setting
Setting Barcode
Cord
ID
Enable
A037A
Disable
A037B
Setting
The setting barcode for USB memory initialization
The data file will be deleted on the USB memory include Data.txt and system.cfg
Description
Setting Barcode
Cyclops-II BlueTooth Scanner Configuration Guide
Cord
46
ID
A029A
Memory Initialization
9.2.5. Barcode Data and Scanner Setting
Description
Pick list
Fuzzy 1D
Setting
Setting Barcode
Cord
ID
Disable
A127A0
Enable
A127A1
Disable
A129A0
Enable
A129A1
Disable
A130A0
Enable
A130A1
Regular
A098A0
Only
Inverse
Barcode
A098A1
Processing
Decoding AIM
Pattem
Inverse 1D
Cyclops-II BlueTooth Scanner Configuration Guide
47
Code ID
UPC-A
UPE-E
UPE-E1
Auto
A098A2
None
A112A0
AIM Code
ID
A112A1
Symbol
Code ID
A112A2
Disable
A042A0
Enable
A042A1
Disable
A043A0
Enable
A043A1
Disable
A044A0
Enable
A044A1
Cyclops-II BlueTooth Scanner Configuration Guide
48
EAN-8
Disable
A045A0
Enable
A045A1
Disable
A046A0
Enable
A046A1
Disable
A047A0
Enable
A047A1
ISBN-10
A048A0
ISBN-13
A048A1
Decode
Ignore
A049A0
UPC/EAN
supplemental
EAN-13
Bookland
EAN
Bookland
ISBN format
Supplementals
Decode with
A049A1
supplemental
Autodiscrimin
A049A2
ate UPC/EAN
supplemental
Enable smart
A049A3
supplemental
mode
Cyclops-II BlueTooth Scanner Configuration Guide
49
Enable
A049A4
378/379
supplemental
mode
Enable
A049A5
978/979
supplemental
mode
Enable
A049A6
414/419/434/
439
supplemental
mode
Enable 977
A049A7
supplemental
mode
Enable 491
A049A8
supplemental
mode
Supplemental
A049A9
user-program
mable Type 1
Supplemental
A049AA
user-program
mable Type 1
and 2
Smart
A049AB
supplemental
plus
user-program
mable 1
Smart
A049AC
supplemental
plus
user-program
mable 1 and
2
Cyclops-II BlueTooth Scanner Configuration Guide
50
UPC/EAN/J
Separate
A051A0
AN AIM
Code ID
format
Combined
A051A1
Separate
Transmissio
ns
A051A2
UPC-A check Disable
Digital
A052A0
Transfer
Enable
UPC-E check Disable
digital
Transfer
UPC-E1
check digital
Transfer
UPC-A
preamble
A052A1
A053A0
Enable
A053A1
Disable
A054A0
Enable
A054A1
None
A055A0
System
A055A1
Country
code
A055A2
Cyclops-II BlueTooth Scanner Configuration Guide
51
UPC-E
None
A056A0
System
A056A1
Country
code
A056A2
None
A057A0
System
A057A1
Country
code
A057A2
Disable
A058A0
Enable
A058A1
Disable
A059A0
Enable
A059A1
Disable
A060A0
Enable
A060A1
preamble
UPC-E1
preamble
UPC-E
convert to
UPC-A
UPC-E1
convert to
UPC-A
EAN-8
convert to
EAN-13
Cyclops-II BlueTooth Scanner Configuration Guide
52
UCC Coupon
Disable
A062A0
Enable
A062A1
Old coupon
report
A063A0
New coupon
report
A063A1
Both
Coupon
A063A2
Disable
A064A0
Enable
A064A1
Disable
A065A0
Enable
A065A1
Disable
A067A0
Enable
A067A1
Disable
A068A0
Extended
Code
Coupon
Report
ISSN EAN
Code128
GS1-128
ISBT 128
Cyclops-II BlueTooth Scanner Configuration Guide
53
ISBT
Enable
A068A1
Disable
A069A0
Enable
A069A1
Auto
A069A2
Disable
A070A0
Enable
A070A1
Disable
A071A0
Enable
A071A1
Disable
A072A0
Enable
A072A1
Disable
A073A0
Enable
A073A1
Concatenation
Check ISBT
Table
Code 39
Trioptic Code
39
Convert
Code39 to
Code32
Cyclops-II BlueTooth Scanner Configuration Guide
54
Code32 Prefix
Code39 Check
Disable
A074A0
Enable
A074A1
Disable
A076A0
Enable
A076A1
Disable
A077A0
Enable
A077A1
Disable
A078A0
Enable
A078A1
Disable
A079A0
Enable
A079A1
Disable
A081A0
Enable
A081A1
Digit
Verification
Transmit
Code39 Check
Digit
Code39 Full
ASCII
Code 93
Code 11
Cyclops-II BlueTooth Scanner Configuration Guide
55
Code11 Check
Disable
A083A0
One Digital
A083A1
Two Digital
A083A2
Disable
A084A0
Enable
A084A1
Disable
A085A0
Enable
A085A1
Disable
A087A0
USS check
A087A1
Digit
Verification
Transmit
Code11 Check
Digit
Interleaved 2
of 5
I 2 of 5 Check
Digit
Verification
digit
OPCC check
A087A2
digit
Transmit I 2 of
Disable
A088A0
Enable
A088A1
5 Check Digit
Cyclops-II BlueTooth Scanner Configuration Guide
56
Convert I 2 of
Disable
A089A0
Enable
A089A1
Disable
A090A0
Enable
A090A1
Disable
A092A0
Enable
A092A1
Disable
A093A0
Enable
A093A1
Disable
A096A0
Enable
A096A1
Disable
A097A0
Enable
A097A1
5 to EAN-13
Discrete 2 of 5
Chinese 2 of 5
Matrix 2 of 5
Matrix Check
Digit
Verification
Transmit
Matrix Check
Digit
Cyclops-II BlueTooth Scanner Configuration Guide
57
Codabar(NW7
Disable
A099A0
Enable
A099A1
Disable
A101A0
Enable
A101A1
Disable
A102A0
Enable
A102A1
Disable
A103A0
Enable
A103A1
Disable
A105A0
Enable
A105A1
Disable
A106A0
Enable
A106A1
)
CLSI Editing
NOTIS Editing
MSI
MSI Check
Digits
Transmit MSI
Check Digit
Cyclops-II BlueTooth Scanner Configuration Guide
58
MSI Check
Disable
A107A0
Enable
A107A1
Disable
A108A0
Enable
A108A1
Disable
A109A0
Enable
A109A1
Disable
A110A0
Enable
A110A1
Disable
A111A0
Enable
A111A1
Disable
A126A0
Enable
A126A1
Digit Algorithm
GS1-DataBar
GS1 DataBar
Limited
GS1 DataBar
Expanded
Convert GS1
DataBar to
UPC/EAN
Micro QR
code
Cyclops-II BlueTooth Scanner Configuration Guide
59
Korean 2 of 5 Disable
US postnet
US Planet
Transmit US
Postal check
A132A0
Enable
A132A1
Disable
A133A0
Enable
A133A1
Disable
A134A0
Enable
A134A1
Disable
A135A0
Enable
A135A1
Disable
A136A0
Enable
A136A1
Disable
A137A0
Enable
A137A1
digital
UK Postal
Transmit UK
Postal check
digital
Cyclops-II BlueTooth Scanner Configuration Guide
60
Japan Postal
Australia
Postal
Australia
Postal
Format
Netherlands
KIX code
USPS
4CB/One
code/Intelige
nt Mail
Disable
A138A0
Enable
A138A1
Disable
A139A0
Enable
A139A1
Auto
Discriminat
e
A140A0
Raw Format
A140A1
Alphanumer
ic Encoding
A140A2
Numeric
Encoding
A140A3
Disable
A141A0
Enable
A141A1
Disable
A142A0
Enable
A142A1
Cyclops-II BlueTooth Scanner Configuration Guide
61
UPS FICS
Disable
A143A0
Enable
A143A1
Level 1
A144A0
Level 2
A144A1
Level 3
A144A2
Level 4
A144A3
Disable
A145A0
Enable
A145A1
Disable
A146A0
Enable
A146A1
Disable
A147A0
Enable
A147A1
Postal
GS1 DataBar
Limited
security
Level
Composite
CC-C
Composite
CC-A/B
Composite
TLC-39
Cyclops-II BlueTooth Scanner Configuration Guide
62
UPC
UPC Never
Composite
Mode
linked
A148A0
UPC always
Linked
A148A1
Auto
Discriminat
e UPC
composite
A148A2
GS1-128
Disable
A149A0
Emulation
mode for
UCC/EAN
composite
codes
Enable
A149A1
PDF 417
Disable
A150A0
Enable
A150A1
Disable
A151A0
Enable
A151A1
Disable
A152A0
Enable
A152A1
Disable
A153A0
Micro PDF
417
Code 128
Emulation
Data Matrix
Cyclops-II BlueTooth Scanner Configuration Guide
63
Data Matrix
Inverse
Enable
A153A1
Regular
A154A0
Inverse
A154A1
Only
Decode
Mirror Image
(Data Matrix
only)
Maxicode
Inverse
Autodetect
A154A2
never
A155A0
always
A155A1
Auto
A155A2
Disable
A156A0
Cyclops-II BlueTooth Scanner Configuration Guide
64
QR Code
QR Invers
Aztec
Enable
A156A1
Disable
A157A0
Enable
A157A1
Regular
A158A0
Inverse
Only
A158A1
Inverse
Auto Detect
A158A2
Disable
A159A0
Enable
A159A1
Cyclops-II BlueTooth Scanner Configuration Guide
65
Aztec Inverse regular
A160A0
Inverse
Only
A160A1
Inverse
Auto Detect
A160A2
Level 1
A161A0
Level 2
A161A1
Level 3
A161A2
Level 4
A161A3
Level 0
A162A0
Redundancy
Level
Security
Level
Cyclops-II BlueTooth Scanner Configuration Guide
66
Level 1
A162A1
Level 2
A162A2
Level 3
A162A3
Inter
character gap
Normal
character
A163A0
size
gap size
Decode
Illumination
Large
character
gap size
A163A1
Decode
Illumination
on
A164A0
Decode
Illumination
A164A1
off
Character
string setting
Illumination
Brightness
No convert
A165A0
Convert all
letters to
Upper case
A165A1
Convert all
letters to
low case
A165A2
Exchange
capital/Sm
all letters
A165A3
Level 1
A166A0
Cyclops-II BlueTooth Scanner Configuration Guide
67
All barcode
Symbologies
be disable
Level 2
A166A1
Level 3
A166A2
Level 4
A166A3
Level 5
A166A4
Level 6
A166A5
Level 7
A166A6
Level 8
A166A7
Level 9
A166A8
Level 10
A166A9
All
Symbologie
s be disable
A167A0
All
Symbologie
s return to
default
A167A1
Cyclops-II BlueTooth Scanner Configuration Guide
68
9.2.6. Alpha-Numerical Setting barcode
This item is for input of Alpha Numerical setting.
Descript
Setting Barcode
Code ID
Stop Input
EOC
Cancel
CL
Descript
Numerical
( Include Hex)
Setting Barcode
Code ID
Setting Barcode
Code ID
0
1
2
3
4
5
6
7
8
9
A
B
Cyclops-II BlueTooth Scanner Configuration Guide
69
Descript
Alphabetic Letter
Setting Barcode
C
D
E
F
Code ID
Setting Barcode
Code ID
A
B
C
D
E
F
G
H
I
J
K
L
Cyclops-II BlueTooth Scanner Configuration Guide
70
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
a
b
c
d
Cyclops-II BlueTooth Scanner Configuration Guide
71
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
Cyclops-II BlueTooth Scanner Configuration Guide
72
w
x
y
z
Cyclops-II BlueTooth Scanner Configuration Guide
73
10. Appendix 1
How to make the setting Code
The code type of BTS700 setting code is Code128
The customer can make the setting code of BT drive address and BT device name by yourself.
How to make the setting barcode of Bluetooth Driver Address
Start Code
Setting ID
Address ( Alpha numerical )
FNC4
A001A
0 ~ 9 , A~ F
Ex. 0011223388AF
※ The barcode muse has a space between FNC4 and A001A.
Example . How to make the setting barcode of Bluetooth device Name
Start Code
Setting ID
Address ( Alpha numerical )
FNC4
A011A
0 ~ 9 , A~ Z, a ~z
Ex. DatatCollector1
※ The barcode muse has a space between FNC4 and A001A.
Cyclops-II BlueTooth Scanner Configuration Guide
74
11. Appendix 2
About Key Code
Function key is pressed during Real mode under HID connection, Function Key code Setting
will set up the key code when press Fn key on the Real mode under HID communication.
The Kye code for terminal host ( Android , iPhone, iPad ) as follow
Key Code(Hex)
Normal
1E
1
+Shift
!
1F
2
@
20
3
#
21
4
$
22
5
%
23
6
24
7
^
&
25
8
*
26
9
﹙
27
0
﹚
28
Return(Enter)
2B
Tab
2C
Space
2D
—
╴
2E
=
+
2F
〔
{
30
〕
}
31
﹨
33
;
$
:
34
‘’
“”
36
,
<
37
.
>
38
/
?
Cyclops-II BlueTooth Scanner Configuration Guide
75

Similar documents

the Blue Moon Vintage Parts Catalog

the Blue Moon Vintage Parts Catalog We are open 9:00 A.M.–6:00 P.M. Tuesday–Friday and 10:00 A.M.–5:00 P.M. on Saturday. You may call us at (770) 447-6945 during these hours, or fax us at (770) 447-5798 24 hours a day, seven days a w...

More information