Installation Instructions - SunHaven Awning

Installation Instructions - SunHaven Awning
Width
Parts List
10'
11'
12'
13'
14'
15'
16'
17'
18'
19'
20'
a) Fabric awning cover
1
1
1
1
1
1
1
1
1
1
1
b) Wall molding assembly
1
1
1
2
2
2
2
2
2
2
2
c) Head rod
1
1
1
2
2
2
2
2
2
2
2
d) Rafter assembly
5
5
6
6
6
6
7
7
8
8
9
e) Front bar assembly
1
1
1
2
2
2
2
2
2
2
2
f) Upright assembly
2
2
2
3
3
3
3
3
3
3
3
i) Valance stabilizer
2
2
2
2
2
2
2
2
2
2
2
j) Lag bolts & washers
8
8
9
11
12
12
13
13
13
14
14
k) Lag shields (brick mount)
8
8
9
11
12
12
13
13
13
14
14
1 pkg
1 pkg
1 pkg
1 pkg
1 pkg
1 pkg
1 pkg
1 pkg
h) Cable zip ties
1 pkg
1 pkg 1 pkg
c) head rod
b) wall molding assembly
d) rafter assembly
e) front bar assembly
i) valance stabilizer
side curtain
(optional)
solar screen
(optional)
f) upright assembly
a) fabric awning cover
front valance
Required tools:
h) cable zip tie
side valance
•
•
•
•
•
•
•
(not provided)
6 ft. step ladder
Tape measure
Power drill
4 ft. level
1/4" allen wrench
Ratchet wrench with 9/16" socket
Wire cutters for cutting cable zip ties
VERSION 1 - 3/07
© 2007 QUEEN CITY AWNING
Installation Instructions - Awning Frame
Wood Mount
top of
awning
Brick Mount
caulk
lag
bolt
lag
3" bolt
washer
wood stud
washer
lag shield
brick
1
2
2a
Mark level line on wall where top of
awning will be attached. Locate
studs in wall and mark stud locations
on wall molding.
Drill 3/8" hole through channel in
wall molding at every other stud
location, approx 32" on center. See
diagram 2a. Position wall molding
on wall and mark holes. For wood
mount drill 1/4" pilot holes for lag
bolts.
For brick mount drill 5/8" holes in
brick then insert lag shields into
holes in brick. See diagram above.
Hint: Where possible locate lag
bolts near awning rafter locations.
3
4
5
Position wall molding on wall surface
and insert 3/8" lag bolt into each
hole and tighten bolt. Caulk top of
wall molding to wall surface.
Connect each end rafter to wall
molding. Insert eye-end of each
rafters into jaw-stub on wall molding.
Connect front bar to end rafters.
Tighten set screws in corner elbows.
6
7
8
Connect remaining rafters to wall
molding. Insert eye-end of each
rafter into jaw-stub on wall molding.
Connect opposite end of each rafter
to front bar and tighten set screws in
T-fittings.
Raise front bar with rafters attached
and insert top of upright into t-fitting
and tighten set screw.
Plumb each upright and attach base
flange and tighten set screw.
Anchor base flange of each upright
to patio or deck surface.
VERSION 1 - 3/07
© 2007 QUEEN CITY AWNING
Installation Instructions - Fabric Awning Cover
wall
molding
awning
cover
1/2" rod
carriage bolt
finger clip
1
2
3
Remove awning cover from storage
bag and position on top of frame
rafters. Spread awning cover across
rafters and insert 1/2" rod into
pocket at top of awning cover.
Position awning cover with rod in
pocket into top channel of wall
molding. Tighten carriage bolt on
each finger clip to secure 1/2" rod.
See diagram above.
Pull awning cover over front bar, start
at each front corner of awning frame,
insert zip ties thru tie band loops and
around front bar, then pull zip ties
tight. Continue to secure cover along
front bar with zip ties about every 10
inches or closer if needed.
4
5
6
Secure awning cover at each end raf- Secure front awning valance to side
ter with zip ties starting at front and
awning valance at each corner by
working to the rear of the awning.
inserting zip ties thru bungee straps.
Continue to insert and tighten zip ties
until cover is drum tight, then cut off
each excess length of zip tie.
Wrap velcro straps on underside of
awning cover around rafter of
awning frame and secure.
7
8
9
Secure back of each side valance to
valance stabilizer bar with black zip
ties.
Attach optional SunSpot Side Curtain
to end rafter with black zip ties.
Secure front of side curtain to front of
awning valance at bungee straps with
black zip ties. Next secure back of
side curtain to stabilizer bar with
black zip tie.
Attach optional SunSpot Solar Screen
to tie band on inside of side curtain
with zip ties. If attaching SunSpot
Solar Screen to front of awning insert
zip ties thru loops at top of solar
screen and around front bar of
awning frame.
VERSION 1 - 3/07
© 2007 QUEEN CITY AWNING
Removal Instructions - Fabric Awning Cover
wall
molding
awning
cover
1/2" rod
carriage bolt
finger clip
1
2
3
Fabric awning cover can be
removed for seasonal storage.
Before removing awning cover for
storage make sure the fabric is clean
and dry. Awning frame can remain
in place all year.
Undo velcro rafter straps. Cut zip ties
at each corner of awning cover and
at back of each valance side. Cut zip
ties along front bar and each end
rafter.
Loosen finger clips and pull awning
cover out of wall molding. Slide 1/2"
rod out of awning cover pocket and
place 1/2" rod back into wall molding to store it, then re-tighten finger
clips. See diagram above.
4
5
Remove awning cover from frame
and lay flat. Inspect awning cover
and remove any dirt or debris.
Fold awning cover and place in
storage bag. Store in a cool, dry
place.
VERSION 1 - 3/07
© 2007 QUEEN CITY AWNING