MilsIP Bulk Encryptor Installation Instructions

MilsIP Bulk Encryptor
Installation Instructions
CONFIDENTIAL
Date: 2016-03-14
Version: 1
Page 1 of 5
Contents
1
Required components ..................................................................................................... 2
2
3
Appliance installations .................................................................................................... 2
2.1
Installing M1 models ............................................................................................................................ 2
2.2
Installing R5 and R10 models ........................................................................................................... 4
MilsIPBE Initial Configuration ........................................................................................ 5
Erik Pollmann
KB_IPBE_Installation Instructions-1xe_01.docx
MilsIP Bulk Encryptor
Installation Instructions
1
CONFIDENTIAL
Date: 2016-03-14
Version: 1
Page 2 of 5
Required components
To execute the installation of a MilsIP Bulk Encryptor (MilsIPBE) equipment you need the following components:
 A computer equipped with a serial communication interface (RS232)
 A terminal program, e.g. Putty, running on the setup computer which must support the following communication modes: Speed 115200 Baud, 8 bits, no parity, 1 stop bit
 A serial console cable with a RJ45 connector at one end to be able to attach to the MilsIPBE
equipment
 A MilsIPBE USB installation stick provided by mils electronic, from which all product types
are installed
2
Appliance installations
The installation procedure depends on the appliance model (M1, R5 and R10).
2.1





Installing M1 models
Connect your PC to the Console Port of the IPBE M1 equipment
Start the terminal program. Connect to COM1 with 115200 Baud
Insert the installation USB stick to one of the USB slots of the equipment
Power on the equipment and hit the ‘TAB’ key permanently to access the BIOS
Go to Boot > Boot node select, and set the value to ‘UEFI’
Erik Pollmann
KB_IPBE_Installation Instructions-1xe_01.docx
MilsIP Bulk Encryptor
Installation Instructions
CONFIDENTIAL
Date: 2016-03-14
Version: 1
Page 3 of 5

Go to Save & Exit > Save Changes and Exit, press Enter and confirm the ‘Save & Exit Setup’
dialog with Yes


The appliance reboots. Hit the ‘TAB’ key permanently to access the BIOS again
Go to Save & Exit, select the UEFI partition of the USB stick as boot device and press Enter

Press any key to continue
Erik Pollmann
KB_IPBE_Installation Instructions-1xe_01.docx
MilsIP Bulk Encryptor
Installation Instructions
CONFIDENTIAL
Date: 2016-03-14
Version: 1
Page 4 of 5

The installation menu appears. Select ‘M1 MilsIP Bulk Encrpytor’ and press Enter to start the
installation

At the end of the installation, the device reboots automatically. Remove the USB stick
2.2 Installing R5 and R10 models





Connect your PC to the Console Port of the IPBE R5/R10 equipment
Start the terminal program. Connect to COM1 with 115200 Baud
Insert the installation USB stick to one of the USB slots of the equipment
Power on the equipment and hit the ‘TAB’ key permanently to access the BIOS
Go to Save & Exit, select the UEFI partition of the USB stick as boot device and press Enter
Erik Pollmann
KB_IPBE_Installation Instructions-1xe_01.docx
MilsIP Bulk Encryptor
Installation Instructions
CONFIDENTIAL
Date: 2016-03-14
Version: 1
Page 5 of 5

Press any key to continue

The installation menu appears. Depending on the desired product type select ‘R5 MilsIP Bulk
Encryptor’ or ‘R10 MilsIP Bulk Encryptor’ and press Enter to start the installation

At the end of the installation, the device reboots automatically. Remove the USB stick
3
MilsIPBE Initial Configuration
After installation, the IPBE appliances have the following default values:
 IP at the Management Port: 10.255.255.100
 Password: ‘6068Mil$’
To configure the equipment, proceed as follows:
 Connect your PC to the Management Port (= Port 1) of the MilsIPBE equipment
 Start a web browser and login with the default IP and the default password mentioned above
 Perform the Initial Configuration as described in the Manual. For this purpose, a MilsCard
and a Site List file have to be provided by the MilsAdministrator
Erik Pollmann
KB_IPBE_Installation Instructions-1xe_01.docx