Price list Price list 2016 - ermes-sub

ERMES-SUB
HIGH QUALITY SPEARGUN COMPONENTS
Price list 2016
PHONE: +39 3407144021
+39 080601202
WhatsApp: +001 8293805702
www.ermes
www.ermes-sub.net
[email protected]
skipe: ermes-sub
ermes
P.I. IT06799850729
C.F. PTRNTN59S29A662X
PATRUNO ANTONIO
FABBRICAZIONE ARTICOLI SPORTIVI
Trigger mechanism
We produce mechanisms with the traditional system and system reverse. The numerous configurations
on request include in some models the short trigger for hilt in wood and the system of gearing down
Roll (patent pending), which allows to have a sensitivity on the trigger unthinkable, the trigger weight
does not vary with increasing load (maximum operating force of 0,500 kg of pulling the trigger of 300 kg
!!!) with virtually unlimited endurance.
Upgrade Phatos D'angelo 2
Kit tooth, trigger mechanism for D'angelo II, with this kit will solve
the problem of hardening of the trigger mechanism Phatos
D'angelo 2, only replacing tooth and original trigger with those
supplied in the kit.
00.0020.00
00.0413.00
Kit Phatos Dangelo 2
Line release
€
€
20,00
6,00
Spear: Slim,Medium,Large
The Spear series is characterized by a new optimization of from 1.5 mm box design, the width of the
box is only 10 mm, 14 mm at the top to facilitate the nocking of shaft. This new concept of the box
causes the recess to be carried out is really small, The profile of the mechanism also has been further
lowered. There are three sizes available, short, medium, long. Locking, in two of the three models
(Short and Medium), you can also do with a single screw behind, after an ad hoc burglary before, where
you can perfectly insert the wedge-shaped box. Of course it is also expected the system usually front
locking after pinning. The components are always 6 mm and is raking perfectly inside the box, without
the use of shims avoiding decentration. Has requested is supplied with Roll system. The line release is
always 2.5 mm and can be quickly mounted to the right or left only unscrewing the nut supplied and
reversing it
00.0014.00
00.0014.01
00.0015.00
00.0015.01
00.0016.00
00.0016.01
Short-Spear
Roll Short-Spear
Medium-Spear
Roll Medium-Spear
Long-Spear
Roll Long-Spear
€
€
€
€
€
€
46,00
50,00
48,00
52,00
50,00
54,00
Back
Mounting screw and plug back side, even with Roll system, and trigger Short. Box thickness 2 mm tooth
and trigger 6 mm, automatic thread release lever, movement with a torsion spring.
00.0001.00
00.0001.01
00.0001.02
00.0001.03
Back
Roll-Back
Back trigger short
Roll-Back trigger short
€
€
€
€
48,00
53,00
48,00
53,00
Evo-Back
To be mounted with only three screws from the top, the installation depth is freely adjustable.
Same features as the Back, possibility trigger short and Roll system.
00.0001.00
00.0001.01
00.0001.02
00.0001.03
Back
Roll-Back
Back trigger short
Roll-Back trigger short
€
€
€
€
50,00
55,00
50,00
55,00
Future-black,Future
Mounting in-line with only three screws from above, it does not need shims for adjustment.
Black color (Black) or steel (Steel), same features of the Back, possibility Roll system.
00.0003.00
00.0003.01
00.0003.02
00.0003.03
Black-Future
Roll Black-Future
Future
Roll Future
€
€
€
€
50,00
55,00
50,00
55,00
Black-Micro
Write mechanism, Box 2 mm thick with anti-reflective black finish, (unpainted) components trigger tooth
6 mm, trigger movement assisted by one torsion spring, line release 2.5 mm, width of the box 16mm,
overall length 45 mm
00.0006.00
Black-Micro
€
45,00
Tekno
Derived from 'Evo Back in economic version, the box has to be 1.5 mm, but the components are 6 mm,
longer than the Evo back of about 5 mm. Supplied with a trigger shorter than about 5 mm, suitable for
rifles with wooden .
00.0012.00
Tekno
€
40,00
Ocean, New Ocean
They differ in the assembly, with only three seen from the New Ocean and traditional system with front
and rear screw plug for the Ocean, have the ability to mount the system Roll, Box 2 mm thick polished
finish, components tooth- trigger 6mm.
00.0007.00
00.0007.01
00.0008.00
00.0008.01
Ocean
Roll Ocean
New Ocean
Roll New Ocean
€
€
€
€
48,00
53,00
50,00
55,00
Steel, Classic
The Classic presents the release line above the box and the screw that supports it also acts as a
regulator of trigger pull. The Steel is a very simple mechanism and spartan but quite reliable.
Technical specifications for the Classic and Steel: 1.5 mm thickness of the box, components trigger
tooth 5 mm line release 2 mm, width of the box 15, overall length 80 mm
00.0009.00
00.0010.00
Classic
Steel
€
€
45,00
32,00
Reel
Plastic components are back from solid Delrin, including the coil. The clutch is jerky with anti-lock
systems, operating bearings, adjustable in intensity. Frame stainless steel 2 mm thick, the attacks are
universal and fit all the guns n trade. Particular attention was paid to the robustness of and design.
Colibrì
Adjustable clutch shots, ball and roller scroll-wire crowds, pull handle a capacity of approximately 25
meters of line 1.5 mm, weight: 140 g, coil diameter 46 mm, overall dimensions in vertical height 49 mm.
01.0010.46
11.0005.00
Colibri
Colibrì Handle replacemtent
€
€
60,00
10,00
Falco 57-77
Adjustable clutch shots, ball and roller scroll-wire idle capacity of approximately 50 meters of wire 1.5
mm for the 57 and 100 meters for 77, coil diameter 60 mm to 57 mm and 77 to 77.
01.0020.57
01.0030.77
11.0006.00
Falco 57
Falco 77
Falco 57 Handle replacemtent
€
€
€
68,00
75,00
12,00
Leonardo 57-77-93
Adjustable clutch shots with ball. Single reel in the world with a guide-wire
guide wire automated., This device will
have the turns of the wire neatly next to one another. The transmission is on request
with pulleys (lighter and quieter) or Sprockets, provide a kit and retractable handle crowds.
00.0040.57
00.0050.77
01.0051.77
01.0060.93
01.0061.93
01.0006.00
11.0008.01
11.0008.00
Leonardo 57 P
Leonardo 77 P
Leonardo 77 R
Leonardo 93 P
Leonardo 93 R
Leonardo-Falco
Falco 57/77 Handle replacemtent
Leonardo 93 Handle replacemtent
Leonardo retractable handle
€
€
€
€
€
€
€
€
110,00
120,00
135,00
130,00
145,00
12,00
12,00
10,00
Sula 80
Adjustable clutch shots sphere, capacity of 50 meters of wire 1.5 for the model 80, the handle can be
removed, the attacks are universal.
01.0070.80 Mulinello Sula 80
11.0007.00 Albatros, Sula Handle replacemtent
€
€
60,00
10,00
Head and roller accessories
Head Roll
The pulleys are chosen from Glass, mono-Iron, and Sliding, free holes and the hole in the graft may be
used if necessary to balance the head with the joint lead.
CNC machined from full, in very strong Delrin, no additional parts steel passes the line is integrated in
the lower profile of the head. Suitable for all pipes with internal diameters from 25.5 to 26.5, the
supplied screws and washers M4 x 60.
03.0018.01
03.0018.02
03.0018.03
Head Roll Sliding+kit screws m4x60
Head Roll Iron + kit screws m4x60
Head Roll Glass + kit screws m4x60
€
€
€
85,00
95,00
95,00
Head Pure Inverter
Machined from solid plastic float, the stopper is shockproof material, specially created for systems to
rope, supplied two or ring that can be moved at will in three specific locations. Supplied screws and
washers M4 x 60
03.0020.00
03.0020.01
Head Pure Inverter Iron
Head Pure Inverter Sliding
€ 100,00
€ 90,00
Support Reel Hook
Support Hook reel is designed to install reels Ermes with 2
comfortable poliers broad-headed screws M4 x 8 (supplied), on
the commercial tube D 28 mm guns are 3 holes installation, the
side has three convenient fastening side for systems .
03.0022.00 Multiblock
€ 28,00
Kit Steel Wood Inverter
Kit inverter for wood easily and inexpensively, is composed of:
inverter stopper stainless steel 4 mm polished, measurements
are calibrated for easy installation, it fastens the wood through the
legs arranged in fish bones for a safe anchorage;
2 pulleys Delrin with single bearing steel with high load and speed;
1 axis 6 x 38 mm screws and washers poliers
03.0019.00 Kit Steel Wood Inverter
€ 48,00
Kit Plastic Wood Inverter
Wood Plastic kit consists of: 1 stopper Delrin , 2 pulleys inverter, 1
axis M4 x 6 x 50mm complete with spacer washers large washers
and screws.
03.0019.01 Kit Plastic Wood Inverter
€ 52,00
Puleggia Inverter
The pulley Inverter and machined from solid delrin, presents a
micro central steel bearing that makes it optimal for all those
systems which require a high operating load, some 122 kg to
38000 rpm, it is known in fact that is the speed of rotation that It
affects the yield of these systems. Please grease before use.
Measuring 6 x 30 x 11 throat 26.
04.3011.00 Inverter D30 x H11 Iron
€ 15,00
04.3011.01 Inverter D30 x H11 Sliding
€
9,00
Stopper Steel Inverter
This stopper is designed to be inserted directly into the wood,
through two simple holes, the anchor legs are fishbone that
prevent leakage from the timber. The thickness is less than 4 mm
It presents two inclined slots for the passage of the line.
07.2300.00 Stopper Inverter Inox
€
12,00
Stopper Q
Stopper Delrin for inverter systems tested, or for wood
Due to its square shape you can plug them into the wood from the
bottom.
03.0021.01 Q stopper + kit screws m4x60
€
18,00
Kit Roller Wood
Kit Roller Mono
Roller Kit Mono base comprises:
1 pair of pulleys Sliding 16 x 28 throat 20 h 14 or 16 mm,
1 axis 6 x 54 with 2 round-head screws Hex key. M4 x 6 plus 2
washers
1 stopper claw mono with 2 countersunk screws 2.9 x 13
1 pair shores wave with 4 screws round head 3.5 x 13;
1 hook pre-tensioning crocus plan
1 scroll-line transformer
Iron configuration: 2 sheaves with bearings Niro Steel 6 x 15 x 5;
Iron mono configuration: 1 pulley bearing Niro Steel 6 x 15 x 5 mm
width 14 or 16;
Glass configuration: 2 sheaves with bearings Glass 6 x 19 x 6;
03.0000.00 Kit pulley 14 sliding
€ 55,00
03.0000.01 kit pulley 16 sliding
€ 55,00
03.0001.00 kit pulley Iron 14 mono cusc.
€ 65,00
03.0001.01 kit pulley Iron 16 mono cusc.
€ 65,00
03.0002.00 kit pulley Iron 16 doppio cusc
€ 70,00
03.0003.00 kit pulley Glass
€ 70,00
Kit Roller Double
Kit double roller base is composed as follows:
2 pairs of pulleys 16 x 28 Sliding groove 19 width 14 or 16 mm;
2 axes 6 x 82 with 4 screws M4 x 6
1 stopper tube 170 with 3 screws self-tapp. 2.9 x 13
1 pair shores wavelengths with 4 screws self-tapp. round head 3.5
x 13
1 scroll-line transformer
Iron configuration: 2 sheaves with bearings Niro Steel 6 x 15 x 5;
Iron mono configuration: 1 pulley bearing 6x15x5 Steel Niro;
Glass configuration: 2 sheaves with bearings Glass 6 x 19 x 6
03.0004.00 Kit pulley 14 sliding
€ 90,00
03.0004.01 kit pulley 16 sliding
€ 90,00
03.0005.00 kit Iron pulley 14 mono bearing
€ 110,00
03.0005.01 Kit Iron pulley 16 mono bear.
€ 110,00
03.0006.00 kit Iron pulley 16 double bearing
€ 115,00
03.0007.00 kit pulley Glass
€ 115,00
Kit Roller Mono Transformer
The kit is compatible and customizable, and can optionally be
equipped with the economical and reliable Pulleys Sliding core
polymer white, single bearing Iron, Glass double ball (22 x 30
throat diameter), Iron and double bearing.
Transformer kit mono roller base is composed of:
1 pair of pulleys Sliding Transformer (diam.28, throat 20, width 16
mm) on request with width 14 mm;
1 board 6 x 54 mm;
1 pair of stopper mono Transformer;
1 shore simple Transformer;
1 bank with stand bar Transformer;
1 hook pretension;
1 grommet Transformer.
Iron configuration: 2 sheaves with bearings Niro Steel 6 x 15 x 5;
Iron mono configuration: 1 pulley bearing Niro Steel 6 x 15 x 5
width 14 or 16;
Glass configuration: 2 sheaves with bearings Glass 6 x 19 x 6
03.0008.00 Kit pulley 14 sliding
€ 65,00
03.0008.01 Kit pulley 16 sliding
€ 65,00
03.0009.00 kit pulley Iron 14 mono bearing
€ 70,00
03.0009.01 kit pulley Iron 16 mono bearing
€ 70,00
03.0010.00 kit pulley Iron 16 double bear.
€ 75,00
03.0011.00 kit pulley Glass
€ 75,00
Components roller
Bearing Iron
Technical table Bearing Iron High Speed.
size
material
static load dynamic load
speed
6 * 15 * 5 niro steel
kg 48
Kg122
38,000
Given the stagnation of salt water, we recommend lubricate it with
lithium grease periodically
04.0696.00 Bearing Iron
€ 6,00
Bearing Glass
Technical table Bearing Glass
Dimensions
material
dynamic static load
6 * 19 * 6 glass / resin acetal kg 7 Kg
9
04.0626.00 Bearing Glass
€
speed
2600
5,00
Pulley Iron mono
Made of Delrin, encompasses within 1 micro stainless steel
bearing, and greater resistance to static and dynamic load, the
measures are: outer 28 mm, 19 mm throat, axis x 6 mm, thickness
14 or 16 mm. It recommends rinsing with fresh water after use and
a splash of lubricant lithium.
04.2814.01 Iron mono bear. D28 x H14
€ 20,00
04.2816.01 Iron mono bear. D28 x H16
€ 20,00
PulIey Iron double
Made of Delrin, encompasses within 2 micro stainless steel
bearing, and greater resistance to static and dynamic load, the
measures are: outer 28 mm, 19 mm throat, axis x 6 mm, thickness
14 or 16 mm. It recommends rinsing with fresh water after use and
a splash of lubricant lithium.
04.2816.02 Iron double bearing. D28 x H16
€ 25,00
Puleggia Sliding
The particular shape of the core, facilitates even more the glide in
the water of the pulley, is maintenance-free, the width of the pulley
is from 14 and 16 mm
04.2814.00 Sliding D 28 x H 14
04.2816.00 Sliding D 28 x H 16
€
€
11,00
11,00
Puleggia Inverter
The pulley inverter is composed of a body in Pom c in which is
housed a micro stainless steel bearing, placed, in a central, each
pulley is able to withstand some 122 kg, to 38,000 rpm, and then
adapts to all systems that require a big load.
04.3011.01 Inverter it D 30 x H 11
€
18,00
Axis
Available different lengths, supplied with screws and washers.
04.3011.01 Axis M3 x 5 x 48 mm
€
6,00
05.0305.65 Axis M3 x 5 x 65 mm
€
6,00
06.0406.38 Axis M4 x 6 x 38 mm
€
6,00
06.0406.48 Axis M4 x 6 x 48 mm
€
6,00
06.0406.50 Axis M4 x 6 x 50 mm
€
6,00
06.0406.54 Axis M4 x 6 x 54 mm
€
6,00
06.0406.60 Axis M4 x 6 x 60 mm
€
6,00
06.0406.65 Axis M4 x 6 x 65 mm
€
6,00
06.0406.70 Axis M4 x 6 x 70 mm
€
6,00
06.0406.82 Axis M4 x 6 x 82 mm
€
6,00
Stopper Artiglio 60 mono
Profile nonlinear designed to cushion the blow of the whip limit
spinner. Featuring numerous lightening, it has two forward-facing
claws that can be used to stop the line. Supplied with self-tapping
screws 2.9 x 13
Claw 60: thickness 2 mm length 60 mm spacing
07.0060.00 Stopper Artiglio 60
€
12,00
Stopper Tube 110
Cut from a tube with outer diameter 16 mm and internal 13 mm
provided with many lightening clean design, avoids cuts the wire in
abutment with the stopper
07.1110.00 Stopper Tube L 110 x 16 x 1,5
€
25,00
Stopper Tube 170
Cut from a tube with outer diameter 16 mm and internal 13 mm
provided with many lightening clean design, avoids cuts the wire in
abutment with the stopper
07.1170.00 Stopper Tube L 170 x 16 x 1,5
€
28,00
Stopper mono Transformer
They can transform any wooden speargun in a roller
performance, with a simple operation you can saw off the head so
that it can accommodate the two opposing stopper that will be
fixed with 4 simple countersunk screws 3.5 x 9.5.
9.5
07.2200.00 Stopp. (2pz) mono Transformer
€
16,00
Stopper a couple
Modular in both width and height, fixed in wooden nails through
integrated anchor.
Stopper 65: thickness 1.5 mm wheelbase 65 mm anchor.
Stopper 130: 1.5 mm wheelbase 130 mm anchor.
07.2065.00 Stopper 65 (2 pz)
07.2130.00 Stopper 130 (2pz)
€
€
7,00
8,00
Banks Transformer
This bank has two nails for hosting the turns of wire, the holes are
4 mm, the wheelbase is 30.7 mm. 1.5 mm thick.
08.0002.00 Banks Transformer
€
4,00
Banks Onda 68-70
Produced in two different sizes, they have a central hole axis of 5
or 6 mm and are equipped with nails for winding line supplied in
couples with four round head screws 3.5 x 13.
08.2668.00 Banks Onda 6 x 68 (2pz)
08.3670.00 Banks 6x 70 (2pz)
€
€
10,00
10,00
Banks Onda 82
They bore central axis of 6 mm and are equipped with nails for
winding line supplied in couples with four round head screws 3.5 x
13
08.2682.00 Banks Onda 6x 82 (2pz)
€
11,00
Hook Eagle mono
Comprising three parts, a base, a central building where you will
engage the spinner textile and a lid with a special adjustable spout
that prevents the accidental release of the spinner the distance is
calculated to keep perfectly lined rubber bands of a single roller.
Width 26mm.
09.0026.00 Hook pret. Eagle mono
€
7,00
Hook Eagle double
Comprising three parts, a base, a central building where you will
engage the spinner textile and a lid with a special adjustable spout
that prevents the accidental release of the spinner the distance is
calculated to keep perfectly lined rubber bands of a double roller.
Width 58mm.
09.0058.00 Hook pret. Eagle double
€
10,00
Hook Croco mono
Align the rubber band under the stem and prevent after the shot
the same jump on, facilitated introduction of the line, comes with 2
round-head screws 3.5 x
09.0016.00 Hook pret. Crocolock mono
€
9,00
Hook Croco double
Line up two pairs of rubber band under the barrel, the same is
supplied with self-tapping screws round head. 3.5 x 19.
09.4424.00 Hook pret. Croco double
€
14,00
Line guide
Hole of generous size, you can adjust the angle of installation with
a simple clamp, very comfortable winding of the coils of line,
provided with two self-tapping screws 2.9 x 13
10.0004.00 Line guide
€
7,00
Bracket camera
The modular system Avant is composed of a support and a movable arm removable, rolling stock, until
the total closure. The advantage is undoubtedly that of being able to position the camera at the desired
distance, up to which, closing it backwards, positions the camera above the back of the speargun
easier to transport. The arm is suitable for all cameras in production and can be removed.
Bracket Avant Ermes
Suitable for the mechanisms Ermes and in general for
mechanisms for guns in wood, the camera in the closed position is
placed right behind the mechanism and in the recovery position
rear. The assembly does not interfere with release system of the
line mechanism.
02.0010.00 Sup. Avant Ermes
€ 12,00
02.0003.05 Arm Avant
€ 13,00
Bracket Avant Ermes-Call fish
Suitable mechanisms for the Ermes and in general for
mechanisms for wood spearguns, the camera in the closed
position is Placed right behind the mechanism and in the recovery
position rear. The assembly does not interfere with release of the
line.
02.0011.00 Sup. Ermes Avant-Call Fish
€ 32,00
02.0003.05 Arm Avant
€ 13,00
Bracket Avant Phatos-Devoto-Apnea
The support of this bracket is adaptable to Pathos-Devoto-Apnea,
attaches to the speargun Phatos with a cable not supplied, and
the Devoto-Apnea with a screw on the back included.
Endowment support: ring, 1 screw M4x40 with nut, 1 screw
M3x10,1 plastic washer.
02.0014.00 Sup. Avant Phatos
€ 12,00
02.0003.05 Arm Avant
€ 13,00
Bracket Avant Omer
The support of this bracket is adaptable to speargun Omer.
Endowment support: ring, 1 screw M4x40 with nut, 1 screw M3x4
0.1 plastic whaser.
02.0013.00
02.0003.05
Sup.Avant Omer
Arm Avant
€
€
12,00
13,00
Bracket Avant C4
The support of this bracket is adaptable to speargun C4.
Endowment support: ring, 2 screw M4x 14
02.0012.00
02.0003.05
Sup. Avant C4
Arm Avant
€
€
12,00
13,00
Bracket Roll Ermes
Bracket born to mechanisms Ermes, in a rest position to a position
exactly behind the center of the mechanism, thus avoiding the
clutter of a traditional bracket, and facilitating the transport of the
speargun. Support consists of a fixed and a mobile arm adjustable
and removable, swinging the arm allows filming the companion
diving safely without pointing your speargun
02.0004.02 Sup. Roll Ermes
02.0003.04 Arm Roll Ermes
€
€
10,00
10,00
Bracket Ermes
Bracket designed specifically for the mechanisms Ermes, for
GoPro, Midland, just one point back fixing, if you want you can
block further using the side holes, is suitable for the whole range
of mechanisms Ermes, precise measurements will offer you the
same you fits perfectly preventing any movement. Includes: rubber
washer and screw the American step.
02.0001.01 Bracket Ermes
€ 15,00
Kit photographic
Photographic camera mounting screw with gasket supplied.
11.0013.00 Kit vite e rondella mont. camera
€
2,50
Knurled Knob
Knob steel parts system Avant and Roll.
knurled knob M4x16x4
€
2,50
Recalls
This useful tool has been designed to be applied across the series of mechanisms Ermes, several
placements are in fact being symmetrical, the wheel can be positioned to the right or left, can also be
operated by holding it comfortably in the hand and attached to the wrist with a drawstring.
The striker beating against the gear making a clicking sound with varying intensity controlled by the
operator, various species are attracted to the characteristic ticking and it is in the imagination of the
fisherman to adapt to the situations that arise
Call-fish Siren
.
With shell and plastic roller., Really small size, universal model
11.0014.00 Call Fish Siren
11.0023.00 Bracket Univ. For Siren
€
€
22,00
3,00
Call-fish Ermes
Suitable for the whole series of Ermes mechanisms , one should
not make additional holes on the rifle, it is fixed on the same holes
of the mechanism..
11.0014.00 Call Fish Ermes
€
18,00
Call-fish Side
Same folding model with a simple clamp, is positioned laterally
and makes it even more comfortable drive
11.0014.01 Call Fish Side
€
22,00
Call-fish C4
Model specially designed to be inserted in C4 spearguns
Equipment: 2 screws M4 x 14, 2 washers plastic
11.0014.03 Call Fish C 4
€
18,00
Call-fish Tube Omer-Apnea-Devoto
Designed for rifles Omer, Apnea, Devoto, making it suitable for
most rifles on the market.
Equipment: 1 screw M4x40 with nut, 1 screw M3 x 40 with nut, two
washers Plastic
11.0014.02 Call Fish Tube Omer
€ 18,00
Other accessories
Dynema
Double braided rope with high tenacity polyester external twists in
opposing and balanced and inner core DYNEEMA® SK75
braided.
14.0015.00 Dynema with sock 1,5 mm
14.0020.00 Dynema with sock 2 mm
€
€
0,50
0,60
Line high tenacity
Double braided rope with outer and inner core braided high
tenacity polyester.
1.6 mm diameter: Tensile strength: kg. 90
14.0016.00 m 1.6 bianco
€
0,25
Hilt 1 hole
Supplied already folded in L, the model can be with the desired
shape, 86 mm long, 2 mm thick
10.0000.00 Hilt 1 hole
€
7,00
Hilt 2 holes
Supplied already folded in L, the model can be with the desired
shape, 86 mm long, 2 mm thick
10.0000.01 Hilt 2 holes
€
7,00
Large plane hilt
Can be shaped at will, it is suitable to be bent and formed an
inverted U, is provided with two self-tapping screws 3.5 x 13
countersunk head
10.0001.00 large plane hilt
€
7,00
Small plane hilt
Can be shaped at will, it is suitable to be bent and formed an
inverted U, is provided with two self-tapping screws 3.5 x 13
countersunk head
10.0002.00 small hilt
€
6,00
Release propeller lever
It interacts with the shaft and thus does not interfere on the
sensitivity of the trigger, always resumes the correct position as it
is of helical shape, measuring 34 mm in diameter, 2.5 mm thick.
00.0405.01 Release propeller lever
€
7,00
Release Ocean
He interacts with the tooth and is mounted in the lower part of the
mechanism.
00.0407.00 Release Ocean
€
6,00
Kit ballast compartment
Lid to the ballast compartment, indispensable to balance his
weapon, with a comfortable passing the line, which can be cut if
necessary, leads not provided, interest measure 18 mm x 90 mm.
complete with inserts and screws M4 x 25 mm.
11.0001.00 Kit ballast compartment
€
8,00
Kit line guide
. Accessories indispensable for the construction in wood
speargun, comprising a push rod line passes from a line guide
plate, complete with 4 screws for fixing countersunk head 2.9 x 13
11.0000.00 kit line guide
€
12,00
€
23,00
kit accessories
composed by:
1 kit line guide
1 hilt
1 kit compartment cover ballast
11.0002.00 kit accessories
Kit midle Handle
Plate central handle, in combination with the remote trigger kit
(sold separately) allows you to build speargun American type,
It includes a hilt two holes and comes with five screws
countersunk 3.5 x 22 and 2 holes hilt.
11.0004.00 Kit Midle Handle
€
45,00
Kit trigger
Kit command mechanism, useful for when you want to retract the
firing mechanism,
anism, is inspired by the speargun with central handle,
is composed of a trigger, 2 platelets holder dipstick, 4 screws, 2.9
x 13, 1 x 300 mm rod 3, and a pin 4 mm x 16 mm.
11.0003.00 Kit trigger
€ 12,00
Fixing
fixing kit three screws
Mounting kit for mechanisms spineless side, you can fix the
mechanism with this handy kit includes 3 Hexagon blind steel M 4
x L 16 and 3 screws round head hex wrench M 4 x L 20, 9 contact
washer elastic thickness stainless
11.0010.00 kit fixing. Mec. 3 screws
€
4,50
Kit trigger fixing
.Fixing
Fixing kit mechanisms, consisting of: 1 plug DA 3 mm x W 55 mm
+ 1 M4 x 20mm L + 1 insert hexagonal blind steel M4 x L 16,
1 contact washer elastic. The convenient insert combined with the
stainless steel screw, makes the detachable fixing and
professional
11.0009.00 kit fixing
€ 2,00
Kit reel fixing
Kit for fixing reels avoiding using self-tapping
tapping screws,
scr
is composed
of 2 Hexagon blind Stainless M 4 x 16 L, 2 round head screws
Allen key M 4 x 14 L, 2 conical spring washers.
11.0012.00
Kit reel fixing
€
2,50
Hexagonal insert
Very comfortable and safe insertion in the wood due to its
hexagonal shape, coupled with the M4 screws, makes the
removable fixing, the blind bottom fixes it from the infiltration of
resin. Measure M4 x L 16
Hexagonal insert M4 x L 16 fondo cieco
€
1,50
€
2,50
Knurled Knob
M4 x 16 x 4
Traction spring with eyelets
Parts mechanisms series Steel , Classic and Call-fish
Call
Traction spring with eyelets
€ 1,50
Torsion spring
Torsion Spring
€ 1,50
Double torsion spring
For old trigger Back
For Trigger New Back
For Trigger Spear
Double torsion spring
€
2,00
Fixing pin
D 3 x L 55
D 4 x L 10
D 4 x L 16
€
€
€
0,50
0,40
0,40
€
€
€
€
€
€
€
0,40
0,40
0,40
0,40
0,40
0,40
0,40
€
€
€
€
€
0,10
0,30
0,15
0,40
0,60
€
€
€
0,10
0,15
0,20
€
€
€
0,20
0,20
0,20
Elastic pin
2,5 x 10
2,5 x 14
2,5 x 16
3 x 14
3 x 16
4 x 30
4 x 32
Hexagon screw
M 3 x L 6,-10
M 3 x L 40
M 4 x L 6,-8-14-20-25
M 4 x L 40,-60
M 4 x L 90
Hexagon screw
M3 x L 5
M 4 x L 14,-16-20
M 5 x L 14
Screw Poliers
M4xL5
M4xL8
M4 x L 12
Hex nut
M3xH4
M4x H5
€
€
0,10
0,10
€
0,30
€
€
€
€
€
0,10
0,10
0,10
0,10
0,10
€
€
0,30
0,30
€
€
0,30
0,30
Wing nut
.
M4
Special whasher
d 4,3 x D 10
d 4,3 x D 9
d 4,3 x D 12
Split D 3
Split D 4
Elastic safety ring
For shaft 4 mm
For shaft 8 mm
Anello elastico di arresto
For shaft 4 mm d 3,2
For shaft 8 mm d 6
Screws
2,9 x L 13
3,5 x L 13
3,5 x L 19
3,5 x L 25
3,5 x L 32
€
€
€
€
€
0,15
0,15
0,15
0,15
0,15
€
€
€
€
€
0,08
0,15
0,15
0,15
0,15
Screws
2,9 x L 13
3,5 x L 9,5
3,5 x L 13
3,5 x L 19
3,5 x L 22