View PDF - AltecAus

presents
Hydraulic Tools
Call Toll Free
1-877-GO ALTEC
9002-00000 09/05
Hydraulic Tools
Impact Wrenches, Drills, and Accessories .....................................................................................p 3
Pole Tampers ....................................................................................................................................p 5
Long-Reach Hydraulic Tools............................................................................................................p 6
Saws ...................................................................................................................................................p 7
Pole Pruners .....................................................................................................................................p 8
Crimping Tools ...................................................................................................................................p 9
Alternator ...........................................................................................................................................p 11
Paving Breakers ................................................................................................................................p 11
Sign Post Drivers and Pullers ..........................................................................................................p 13
Rock Drill and Chipping Hammer ....................................................................................................p 13
Ground Rod Drivers and Pole Pullers .............................................................................................p 14
Submersible Pumps .........................................................................................................................p 15
Power Units .......................................................................................................................................p 16
Miscellaneous Hydraulic Tools ........................................................................................................p 16
Reels and Accessories .....................................................................................................................p 17
Hydraulic Tool Accessories .............................................................................................................p 18
Hydraulic Tool Replacement Parts ..................................................................................................p 19
Call Toll Free
1-877-GO ALTEC
Fairmont Impact Wrenches, Drills, and Accessories
Impact wrench and drill with 7/16” hex and 1/2” square
drive. For use on an open or closed-center hydraulic system. Internal control prevents overspeeding and allows
up to 12 gpm. This impact operates
in both forward and reverse. The
impact features high torque for drilling
salt-cured and creosoted poles and
a handle that is heat-insulated and
ergonomically positioned for comfort.
A twin hammer impact mechanism
aids in increasing performance and
reliability.
• Available with variable torque control adjustable from 80 to 400 ft.-lb.
• Flow range of 4 - 12 gpm, optimum flow range of 5 - 8 gpm
• Operating pressure of 1,000 - 2,000 psi
• Weighs: 7.1 lbs.
P/N 7010-69023
P/N 8126-20300
Fairmont 48330
Fairmont 48755 - Adjustable Torque
This compact, lightweight reversible
and variable speed drill is ideal for
line construction applications. For
use on an open or closed-center
hydraulic system.
• 1/2” reversible drill
• Weighs 6 lbs.
• Flow range of 4 - 8 gpm
• Operating pressure of 1,000 - 2,000 psi
P/N 9000-42260
Fairmont H6400C
Naileater Impact Bits
Naileater impact bits quickly bore through
creosoted and salt-treated utility poles.
They resist wear and even eat through
nails and staples. The self-feeding screw
point draws the bit through the wood.
9/16”
13/16”
11/16”
15/16”
18” Length
P/N 9000-37868
P/N 9000-37870
P/N 9000-37869
P/N 9000-37871
24” Length
9000-37875
9000-37874
9000-37876
Mag Timber Drill Bit
This 3/4” square drive and 5/8” hex
quick change chuck impact wrench
has added power and torque for
heavy-duty jobs. Operates on either
an open or closed-center hydraulic
system.
• Flow range of 4 - 6 gpm
• Operating pressure of 1,000 - 2,000 psi
• Torque at 6 gpm is 2,150 ft.-lb.
P/N 9000-42268
This 1” square drive impact wrench is
heavy-duty enough to be used in multiple
applications. This reversible wrench is run
on an open-center hydraulic system.
• Flow range of 4 - 6 gpm
• Operating pressure of 1,000 - 2,000 psi
• Torque at 6 gpm is 2,150 ft.-lb.
P/N 9000-42274
9/16” x 7/16” shank - P/N 9000-73009
11/16” x 7/16” shank - P/N 9000-73011
Fairmont H6520
This rotary impact hammer drill features adjustable flow control that prevents overspeeding and allows precise control
of drilling speed. The reversible drill can be used on either
an open or closed-center hydraulic system.
• Hammer drills concrete, brick, rock, and other difficult materials
• Drill in wood or steel with auxilliary chuck
• Selector for drill or hammer/drill modes
• Flow range of 5 - 10 gpm
• Operating pressure of 1,000 - 2,000 psi
P/N 9700-42309
Fairmont HID6506
Nut Runner
The nut runner is used for installing and
tightening the four most common sizes
of pole hardware - 3/4”, 13/16”, 1”, and
1 1/8”. The nut runner’s hollow design
allows those bolts that extend up to 6”
beyond the nut to be accommodated.
Includes a 7/16” hex adapter for use
with impact wrenches and drills.
P/N 9000-99795
P/N 9000-99796
• 30” overall with a 26” long flute
• Double flute and double spur design for clean holes and quick
chip removal
• Available in numerous sizes
Fairmont H6510A
Nut Runner Assembly
Nut Runner Replacement Adapter
Adapters
These square drive, 7/16” x 1/2” drive shank adapters are
used with impact wrenches.
P/N 9000-15321
P/N 9000-99489
Fairmont F015321
Fairmont 49314
Heavy Duty
3
Stanley Impact Wrenches, Drills, & Accessories
ID07 Impact/Drill Wrench
DL07 Drill
• Ideal for nut and bolt driving, anchor bolt setting, and wood drilling
• Rugged swing hammer impact mechanism reduces torque transmission
to operator
• Drills holes from 1/2” to 1-1/16” diameter, 18” in length and 1/2” to 11/16” fasteners
• Dual Spool for O.C. or C.C. hydraulic systems.
• Detent type forward/reverse spool.
• Reverse check valve to prevent incorrect connection.
• Integral HYREVZ™ gear-type motor.
• Large trigger for gloved operation.
• Trigger guard
The Stanley DL07 Drill is a 1/2 inch capacity drill for drilling in wood,
metal, or masonry. Stanley DL07 features are:
• 12 gpm (45 lpm) maximum operating range.
• 1/2 in. keyed Jacobs® Chuck.
• Assist handle.
• Integral HYREVZ™ gear-type motor.
• Reversable.
• Open-center or closed-center operation
• Couplers, whip hoses, and assist handle included.
Capacity: 7/16” QC
Torque: 500 ft. lb.
Pressure: 750 - 2,000 psi
Flow Range: 4 - 12 gpm
Weight: 7.2 lbs.
Length: 10 in.
Width: 4.5 in.
Chuck Size: 1/2”1, 5/8”2
Range: 3 - 10 gpm
Weight: 6 lbs.
Length: 9 in.
Width: 4 in.
Pressure: 1000-2000 psi
Altec P/N
9000-07815
Altec P/N
P/N 9000-20025
Stanley P/N
ID07815
Stanley P/N
DL07550
Miscellaneous Impact Wrenches & Accessories
Reliable Impact Wrench
• 12” square drive
• Designed with an E-Z selector for use
on both open or closed center hydraulic systems
• Light weight of 6.3 lbs.
• Delivers 425 ft.-lb. torque at 6 gpm
• 1/2” square drive nose configuration
will accept standard 1/2” drive impact
sockets
Ingersoll-Rand Electric
Impact Wrench
• Industrial Duty Electric, 5/8” Hex Drive
Impact Wrench
• The wrench has a built-in 5/8” quick
change chuck for faster tool changes
• Comes standard with an 8’ cord
Standard Sockets
Heavy Duty, 5/8” Hex Impact Type
P/N 9817-52738
P/N 9817-53398
P/N 9817-52741
P/N 9910-05374
P/N 9817-52740
P/N 9910-05376
P/N 9817-53232
P/N 9817-52744
P/N 9700-10785
P/N 9817-53399
9/16”
5/8”
7/8”
11/16”
3/4”
13/16”
15/16”
1”
1-1/16”
1-1/8”
Deep Sockets
Heavy Duty, 5/8” Hex Impact Type
P/N 9000-96175
P/N 9910-05384
P/N 9817-53401
P/N 9817-53230
P/N 9817-53400
P/N 9817-53233
P/N 9817-52734
P/N 9910-05372
11/16”
3/4”
13/16”
1”
1-1/16”
1-1/8”
2-in-1 Lineman’s Socket
Altec P/N
360-20035
360-20034
Call Toll Free
1-877-GO ALTEC
4
Stanley P/N
33155 13/16” & 15/16”
33156 1” and 1-1/8”
Fairmont Pole Tampers
These pole tampers make quick work of
setting poles, asphalt patch, and general
construction backfill compacting. There are
only three moving parts for low maintenance.
A reversible on/off valve allows these tampers
to be used on an open or closed-center hydraulic system. Comes standard with a
kidney-shaped foot.
These tampers make quick work of setting poles,
asphalt patching, and general construction backfill compacting. With only three moving parts,
the maintenance of these tampers is low. The
rotating trigger spool allows these tampers to be
used on either an open or closed-center hydraulic
system. Comes standard with a kidney-shaped
tamper foot.
• Hose end valve
• Kidney shaped foot standard (P/N 900040301), 6” round (P/N 9000-40371) or 4” x 8
13/16” rectangular (P/N 9000-40372) also
available.
• Available in 60” and 72” lengths
• Flow range of 4 - 6 gpm
• Operating pressure of 1,000 - 2,000 psi
P/N 8930-00400
P/N 7010-69148
60”
85”
• Valve on tube.
• Kidney shaped foot standard (P/N 9000-40301), 6”
round (P/N 9000-40371) or 4” x 8 13/16” rectangular
(P/N 9000-40372) also available.
• Available in 60” and 72” lengths.
• Flow range of 4 - 6 gpm.
• Operating pressure of 1,000 - 2,000 psi.
P/N 9000-42200
P/N 7010-69084
Fairmont H4802
Fairmont H4802-1
60”
72”
Fairmont H4802-3
Fairmont H4802-5
Stanley Pole Tampers & Accessories
• Pole tamper - without valve
• Kidney-shaped foot standard, round or
rectangular are available
• Pole tamper - valve on tube
• Kidney-shaped foot standard, round or
rectangular are available
Altec P/N
360-30013
Altec P/N
360-30001
Stanley P/N
TA54603 - 3 ft.
Stanley P/N
TA54103 - 3 ft.
Optional Accessories:
Altec P/N
0360-30010
9000-30013
9000-30014
Stanley P/N
00833
00840
01070
Description
Kidney-shaped shoe, 3 x 8 in. diameter
Round shoe, 6 in. diameter
Rectangular shoe, 4 x 8 in. diameter
Reliable Pole Tamper
• Makes quick work of setting poles, asphalt patching and general construction backfill compacting
• Reversible on/off valve for open and closed-center systems
• Standard with kidney-shaped foot
• 60 ft. length
• 1,160 blows per minute @ 5 gpm
P/N 9007-00060
5
Fairmont Long-Reach Hydraulic Tools
Utility Pruners -- Fairmont
These pruners are used for line clearing and
selective pruning of shade trees. The insulated
fiberglass extension tubes are tested to meet
OSHA regulation 1910.269. A heavy cut capacity
allows users to cut branches up to 2 inches.
Long-Reach Chain Saw -- Fairmont
These long-reach chain saws cut hard-to-reach
branches from aerial baskets or from the ground.
The insulated fiberglass extension tubes are tested
to meet OSHA regulation 1910.269. Safety features
include: two-step trigger, trigger guard, and fully
covered sprocket guard. Additional safety features
include an anti-kickback chain and automatic
chain oiler. The Super Spool™ selector control
allows these chain saws to be used on either an
open or closed-center system.
• Trigger guard
• Heat-insulated handle
• Full power return
• 86” overall length
• Flow range of 4 - 6 gpm
• Operating pressure of 1,000 - 2,000 psi
P/N 7010-69147
P/N 7010-69149
P/N 9000-48525
Fairmont 48200
Fairmont 48520
Fairmont 48525
• Available in three lengths - 62.5”, 75”, and 88.5”
• Cut capacity of 13”
• Flow range of 5 - 8 gpm
• Operating pressure of 1,000 - 2,000 psi
• Chain size of 0.325” pitch
Super Sleeve™
Open-Center
Closed-Center
P/N 7010-69018
P/N 9000-38568
P/N 7010-69017
Orchard Pruner -- Fairmont
This heavy-duty large capacity pruner is a valuable tool for the tree care industry. The pruner is
lightweight at only 7.7 lbs., and has a full trigger
guard and heat barrier grip. This pruner runs off
an open-center hydraulic system. This pruner is
not to be used near high voltage lines.
• Cut capacity of 1 3/4”
• Overall length of 60”
• Flow range of 4 - 6 gpm
• Operating pressure of 1,000 - 2,000 psi
P/N 9000-42909
Fairmont 42909
Circular Saw -- Fairmont
This circular saw is used for high production utility line
clearing and general tree clearing applications. This circular saw is not to be used for ground level
operation. Safety features include: hand
stop safety collar, trigger guard, two-step
safety trigger and branch stop. The insulated fiberglass extension tube has been
tested to meet OSHA regulation 1910.269.
The angular head design makes flush cuts
easier and directs chips away from the
operator. Operates on either an open or
closed-center hydraulic system.
• Standard 9” diameter blade
• Cut capacity of 3.5”
• Weighs 9 lbs.
• Overall length 82”
• Flow range of 4 - 6 gpm
• Operating pressure 1,000 - 2,000 psi
P/N 7010-69155
Fairmont 43180
Circular Saw Accessories
P/N 9000-42853
9” blade
P/N 9000-43973
9” chain blade
P/N 9000-54878
Chain for P/N 9000-43973
62.5 in.
75.0 in.
88.5 in.
Long-Reach Chain Saw -- Fairmont
These long-reach chain saws feature a newly designed
handle. Oil does not flow through the handle of these saws.
This allows the handle to stay cool while the saw is
in use. These saws also feature a “gasoline chain saw” style two-step trigger. The
improved two-step trigger operates like a
gasoline chain saw for ease of use while
performing professional tree trimming and
line work from aerial lifts. The insulated
fiberglass extension tube has been tested
to meet OSHA Regulation 1910.269. The
extended length of the saw makes reaching
in to tree centers easy, and the high speed
of the 0.325” pitch chain makes quick work
of the cut. These saws are equipped with
a standard bar of 13” and are available in
three lengths.
• Available in 62.5”, 75”, and 88.5” length
• Cut capacity of 13”
• Super Spool™ selector control for use on open or closedcenter hydraulic systems.
• Flow range of 5 - 8 gpm
• Operating pressure of 1,000 - 2,000 psi
P/N 9000-46310
P/N 9000-46305
Fairmont 46310
Fairmont 46305
Long-Reach Chain Saw Accessories
P/N 7017-89901
11” Bar
P/N 7017-89902
11” Chain
P/N 9000-43369
13” Bar
P/N 9000-43370
13” Chain
P/N 9000-48266
16” Chain
P/N 9000-48265
16” Bar
P/N 9000-99929
Bar Tip Guard
Call Toll Free
1-877-GO ALTEC
6
Fairmont 43178
Fairmont 38568
Fairmont 43177
62.5 in.
75.0 in.
Stanley Chain Saws
Pole Saw
• Lightweight 5 ft fiberglass pole offers convenient handling in tight places
• Dual spool feature permits the user to operate the saw from either
open or closed-center circuits
• Automatic chain oiling for long, reliable service
• Low kick-back chain is standard
• HyrevzTM Motor
• Pressure: 1000-2000 psi
• Length: 74”
• Weight: 9 lbs.
Altec P/N
0360-00008
0360-00016
8126-54106
Stanley P/N
CS23811
CS23821
CS23831
Cutting Capacity
12 in.
15 in.
18 in.
Replacement Bar
360-09037
8126-00156
Replacement Chain
360-09036
8126-02037
Replacement Bar
8126-08347
8126-07683
8126-08347
8126-07683
8126-04643
Replacement Chain
8126-08348
8126-07641
8126-08348
8126-07641
8126-07642
Standard Chain Saw
• Ideal for all types of pruning and clearing applications
• Models designed for use on HTMA Type I or II circuits
• Automatic chain oiling for long, reliable service
• Unconventionally high power-to-weight ratio
• Interlocking trigger, hand guard, and low kickback bars and chains
• HyrevzTM motor
• Dual spool for open center or closed center operation
Altec P/N
8126-05610
0360-00020
8126-06610
0360-00022
0360-00003
Stanley P/N
CS05610
CS05620
CS06610
CS06620
CS06630
Cutting Capacity
12 in.
15 in.
12 in.
15 in.
20 in.
Stanley Circular Saws
• Hydraulic blade brake minimizes coast-down time
• Lightweight fiberglass poles for convenient handling in tight spots
• Angled head design for more visibility and reduced operator fatigue
• Double cone-lock blade nut
• Uses a unique one-piece angled motor and yoke for durability
Blade diameter:
Pressure:
Flow Range:
Weight:
Length:
Connection:
9”
1,000 - 2,000 psi
5 - 7 gpm
9.75 lbs.
79”
3/8” NPT Male Adapter
Altec P/N
360-00007
Stanley P/N
CR27891
9” Replacement Blade
9000-34356
7
Fairmont Standard and Pistol-Grip Chain Saws
Standard Chain Saw -- Fairmont
Pistol-Grip Chain Saw -- Fairmont
These standard chain saws are ideal for large trimming applications and cut-up removal jobs. Super Spool™ selector
control for open and closed-center hydraulic systems. The
handle position on these saws can be oriented to horizontal, 60 or 30 degrees relative to bar and chain according
to operator preference. Safety features on these saws
include: two-step safety trigger, high impact polymer front
handle/shroud, wide lower handle protects hands/knuckles,
chain catcher stops chain rotation. The chain and bar can
be adjusted without removing the sprocket cover. The
sprocket cover can be removed without tools for easy saw
cleaning. Automatic chain oiler can be adjusted without
tools. These saws come with 12” steel braided whip hoses.
(Couplers not included.)
This lightweight pistol-grip chain saw is ideal for cutting
back or trimming from an aerial basket. The Super Spool™
selector control allows this saw to be used on open or
closed-center hydraulic systems. The handle position on
this saw can be oriented to horizontal, 60, or 30 degrees
relative to bar and chain according to the operator preference. Safety features include: two-step safety trigger, high
impact polymer front handle/shroud, wide lower handle
protects hands/knuckles, chain catcher stops chain rotation. The chain and bar can be adjusted without removing
the sprocket cover. The sprocket cover can be removed
without tools for easy saw cleaning. Automatic chain oiler
can be adjusted without tools. These saws come with 12”
steel braided whip hoses. (Couplers not included.)
• Chain pitch of 3/8”
• Cut capacities range from 16” - 24”
• Flow range of 4 - 8 gpm
• Operating pressure of 1,000 - 2,000 psi
• Cut capacity of 13”
• Chain size is 0.325” pitch
• Flow range of 4 - 8 gpm
• Operating pressure of 1,000 - 2,000 psi
P/N 9000-49566
P/N 9000-49603
P/N 9000-49604
Fairmont HCS816
Fairmont HCS820
Fairmont HCS824
16 inch
20 inch
24 inch
P/N 9000-49565
Fairmont HPS513
Stanley Pole Pruners
Altec P/N
0360-00014
8126-40231
Cut Capacity:
Pressure:
Flow Range:
Weight:
Length:
Stanley P/N
PR41131 - oc
PR41231 - cc
2.25 in
1,000 - 2,000 psi
3 - 9 gpm
11.5 lbs.
84 in.
• Operates from a tree-trimming vehicle or bucket truck
• Strong outer tube provides increased durability and extended tool life
• Light weight and easy to use handle
• Built in trigger guard
• External knife adjustment for easy routing maintenance
Call Toll Free
1-877-GO ALTEC
8
13 inch
Fairmont Low Pressure Hydraulic Crimping Tools
5 Ton Crimping Tool
This crimper does not require a high pressure intensifier.
Accepts Burndy “W” dies and Kearney “O” dies. Comes
standard with Kearney “D” dies. Rotating allows easy tool
positioning. Operates on either an open or closed-center
hydraulic system. Relief valve signals operator when crimp
is complete.
• 1” jaw capacity
• Weight - 11.75 lb.
• Flow range of 3 - 9 gpm
• Operating pressure of 1,400 - 2,500 psi
P/N 9000-48740
Fairmont 48740
12 Ton Crimping Tools -- Fairmont
These crimpers do not require a high pressure intensifier.
Operates on either an open or closed-center hydraulic
systems. Each has a flow range of 3 - 9 gpm and an operating pressure of 1,500 - 2,000 psi. Their crimping force
at 1,500 psi is 24,000 lbs.
• Jaw Opening 1.20”
• Weight - 18.5 lb.
• Accepts standard “U”-style dies
• Compatible with dies for: Burndy Y35; Alcoa 12A, 12AC, 12HA,
12HAC; and Anderson HC-12, HC-12H
P/N 9000-42184
Fairmont LPK1230
• Jaw Opening 1.65”
• Weight - 19.7 lb.
• Crimps up to 750 MCM copper and aluminum
• Compatible with dies for: Burndy Y35; Alcoa 12A, 12AC, 12HA,
12HAC; Anderson HC-12, HC-12H and Thomas & Betts 12-ton
P/N 9000-49345
Fairmont LPK1240
15 Ton Crimping Tool
This crimper does not require a high pressure intensifier.
Relief valve signals operator when crimp is complete. This
crimper operates on either open or closed-center hydraulic
systems. Compatible with dies for: Kearney PH2*, PH4/
PH14; Burndy Y35*, Y46; Teledyne TPU-15PH*; Thomas
& Betts TBM 15PF*. The crimper can be converted
with adapters for use with
Burndy “U”-style dies and
Kearney PH2 as well as
some WH12 dies.
*Requires Adapter
• Weight - 28.6 lb.
• Crimping force at 1,500 psi - 30,000 lb.
• Flow rate of 3 - 9 gpm
P/N 9000-48750
Fairmont LPK1550
Quad-Point Dieless Crimping Tools
No high pressure intensifier required. These lightweight
tools complete crimps in seconds. Uses four indentors to
make the crimp. Operates on an open or closed-center
hydraulic system. Head rotates for easy tool and connector
positioning. P/N 9000-88836 uses a pull pin to open head for
easy removal from connector.
• Weight - 12.7 lb.
• Crimping force at 1,400 psi - 6.2 tons
• Flow rate of 3 - 9 gpm
• Operating pressure of 1,400 - 2,500 psi
P/N 9000-49605
Fairmont LPK06AT
• Weight - 19.5 lb.
• Compatible with dies for
Kearney PH-2 and PH-3 tools
P/N 9000-48735
Fairmont LPK1240K
• Flip-top head
P/N 9000-88836
Fairmont LPK06FT
9
Fairmont Low Pressure Hydraulic Crimping Tools,cont.
60 Ton Crimping Tool -- Fairmont
This tool is ideal for use in substation and transmission construction. To remove
splices, the top of the head easily swivels 90 degrees and then can be lifted
from the tool. Removing the tool from the stand exposes a lifting eye that is
used when the tool must be used above ground level. This tool accepts Burndy
“L” dies and Alcoa “6000 Series” crimping dies. Operates with most 10,000
psi hydraulic power systems. Includes steel carrying case with storage space
for dies.
• Weight - 45 lb.
• Oil volume required - 0.75 pint
• Crimping force at 10,000 psi - 120,000 lbs.
P/N 9000-10604
Fairmont RK6040
Stanley Hydraulic Crimping Tools
Stanley crimping tools operate from truck system pressure -- there is no high pressure intensifier required. An accurate
built-in pressure relief ensures that a full die load is achieved at the minimum 1650 psi and prevents over-crimping if
higher pressure is present. Continuous 360 degree rotation of the cylinder and die head allow for easy crimp alignment
and the patented open center/closed center selector permits use on either type of hydraulic system.
ALTEC P/N
9000-00449
Pressure:
Flow Range:
Weight:
Length:
Width:
Capacity:
Connectors:
STANLEY P/N
CT15036UN
1,650 - 2,500 psi
3 - 9 gpm
29 lbs.
29 in.
7 in.
500 MCM Copper, 1500
MCM Aluminum and 795
MCM ACSR
3/8” male pipe adapter to
-8 SAE port
ALTEC P/N
9000-00448
Pressure:
Flow Range:
Weight:
Length:
Width:
Connectors:
Capacity
STANLEY P/N
CT06026N
1,650 - 2,500 psi
3 - 9 gpm
13 lbs.
20 in.
7.25 in.
3/8” male pipe adapter to
-8 SAE port
#10-750 MCM Aluminum
& #10-500 MCM Copper
ALTEC P/N
9000-00446
9000-00447
Uni. Pressure:
Flow Range:
Weight:
Length:
Width:
Capacity:
Connectors:
Crimping connectors to electric power cable
with Anderson VC6 die-less head
Reliable 60-Ton Hydraulic Crimping Tool
The 9000-60000 double-acting, 60-ton press is designed to compress sleeves and
lugs on ACSR and ACAR transmission and distribution cables. Operable from any
10,000 psi pumping source, these tools are portable for easy positioning. Accepts
most shell type dies currently used with Alcoa, Burndy, and Huskie 60-ton presses.
Double acting feature eliminates the possibility of jamming or hanging up. 3/8”
screw-type couplers included. Also comes with tool stand and steel case.
• 60 ton output
• Weighs 47 lbs.
• 5” wide x 17” high
P/N 9000-60000
Call Toll Free
1-877-GO ALTEC
10
STANLEY P/N
CT10066AN
CT10064A
1,650-2,500 psi
3 - 9 gpm
17 lbs.
22 in.
7 in.
#10-750 MCM Aluminum
& #10-500 MCM Copper
3/8” male pipe adapter to
-8 SAE port
Stanley Alternator
• Applications include power for lights, small electric tools, etc.
• Weighs less than one-third of gas or diesel powered alternators
• Convenient to handle and uses very little space in vehicle
• Built-in circuit breaker protection
• Brushless design reduces maintenance
Output:
ALTEC P/N
0683-70118
STANLEY P/N
AL35095
Pressure:
Flow Range:
Weight:
Length:
Width:
Height:
3,500W, 120/240V,
60 Hz
1,000 - 2,000 psi
7 - 9 gpm
70 lbs.
19 in.
9 in.
10 in.
Fairmont Paving Breakers
25 LB Hydraulic Breaker -- Fairmont
35 LB Hydraulic Breaker -- Fairmont
This 25 lb. hydraulic breaker is light enough and small
enough to be easily stored on trucks. The versatile breaker
is light enough to be used in a horizontal position. This
breaker is also much quieter than its pneumatic counterpart. Hydraulic cushioning of the ram return stroke helps
to reduce operator fatigue. The lever-style latches ensure
quick tool changes.
The 35 lb. hydraulic breaker is light enough and small
enough to be easily stored on trucks.
This breaker is also much quieter
than its pneumatic counterpart. Vibration-isolated, cushioned handles and
hydraulic cushioning of the ram return
stroke help to reduce operator fatigue.
The lever-style latches ensure quick
tool changes.
• Uses tools with 1” x 4 1/4” shanks.
• Uses tools with 7/8” x 3 1/4” shanks.
P/N 9000-49537
P/N 9000-49538
Fairmont HPB25
Fairmont HPB35
45 LB Hydraulic Breakers -- Fairmont
55 LB Hydraulic Breakers -- Fairmont
The 45 lb. hydraulic breaker is great for breaking sidewalks
and curbs, or for driving ground rods and other small demolition jobs. Operator comfort is a key design feature in these
45 lb. breakers. The modular design minimizes protrusions
that rub on operators’ legs, and provides
reduced noise and vibration levels. An
integrated rubber damper in the front head
reduces chisel noise. Standard breaker
models feature vibration-dampened and
cushioned handles. AVS tools have
patented spring-dampened handles that
reduce the vibration transmitted to the
operator by 80 - 90%. All breakers are
equipped with a two-step trigger.
The 55 lb. hydraulic breaker has a high blow energy, providing maximum breaking power that can handle those big
demolition tasks with ease. The modular design of these
breakers minimizes protrusions that rub on operators’ legs,
and provides reduced noise and vibration levels. An integrated rubber
damper in the front head reduces
chisel noise. Standard breaker models feature vibration-dampened and
cushioned handles. AVS tools have
patented spring-dampened handles
that reduce the vibration transmitted to the operator by 80 - 90%. All
breakers are equipped with a twostep trigger.
• Flow range of 5 - 8 gpm
• Blow energy of 63 ft-lb.
• Open-Center hydraulic system
P/N 9000-02195
P/N 9000-02196
P/N 9000-02197
P/N 9000-02198
Fairmont HPB45-1
Fairmont HPB45-2
Fairmont HPB45-1AVS
Fairmont HPB45-2AVS
1 1/8” x 6”
1” x 4 1/4”
1 1/8” x 6” AVS
1” x 4 1/4” AVS
• Flow range of 5 - 8 gpm
• Blow energy of 81 ft-lb.
• Open-Center hydraulic system
P/N 9000-02199
P/N 9000-02200
P/N 9000-02201
P/N 9000-02202
Fairmont HPB55-1
Fairmont HPB55-2
Fairmont HPB55-1AVS
Fairmont HPB55-2AVS
1 1/8” x 6”
1 1/4” x 6”
1 1/8” x 6” AVS
1 1/4” x 6” AVS
11
Fairmont Paving Breakers, cont.
75 LB Hydraulic Breakers -- Fairmont
The 75 lb. hydraulic breaker has a high blow energy, providing maximum breaking power that can handle those big
demolition tasks with ease. These breakers provide an
impressive 118 ft-lbs. of blow energy at 1,500 times per
second, yet the sound level is only 93 dBa when measured
at a distance of 3 feet. The operator comfort is another
key design feature in these 75 lb. breakers. The modular
design minimizes protrusions that rub on operators’ legs,
and provides reduced noise and vibration levels. An integrated rubber damper in the front head reduces chisel noise.
Standard breaker models feature vibration-dampened
and cushioned handles. AVS tools have patented springdampened handles that reduce the vibration transmitted to
the operator by 80 - 90%. All breakers are equipped with
a two-step trigger.
P/N 9000-09751
P/N 9000-02204
P/N 9000-02205
P/N 9000-02206
Fairmont HPB75-1
Fairmont HPB75-2
Fairmont HPB75-1AVS
Fairmont HPB75-2AVS
1 1/8” x 6”
1 1/4” x 6”
1 1/8” x 6” AVS
1 1/4” x 6” AVS
Paving Breaker Accessories
P/N 9000-41706
Moil Point 1 1/8” x 6”
P/N 9000-41707
3” Chisel 1 1/8” x 6”
P/N 9000-41708
5” Asphalt Cutter 1 1/8” x 6”
• Flow range of 7 - 9 gpm
• Blow energy of 118 ft-lb.
• Open-Center hydraulic system
Stanley Paving Breakers
BR37110 is a lightweight breaker wellsuited for breaking sidewalk and curbing, asphalt cutting and driving rods. Its
handy size and lightweight construction
make it particularly useful for use as a
digger in trench work where horizontal
operation is required.
BR40550 is the ideal breaker for light applications where noise and economy of
operation are prime concerns. Requiring
only 5 gpm of hydraulic flow, the BR40 is
lightweight, making it ideal for light construction applications where horizontal
operation might be required.
• Suitable for light to heavy concrete demolition, driving of posts, pole anchors, and
asphalt cutting.
• Each features a trouble-free diaphragm
accumulator and can handle system back
pressures of up to 250 psi/17 bar.
Altec P/N
8126-37110
Stanley P/N
BR37110 7/8” hex oc
The rugged, lightweight, and powerful
construction of the BR45130 makes it
ideal for use in the 35-65 lb. class. Designed for light-to-medium duty operation, they excel at curb and sidewalk demolition, asphalt cutting, and are popular
for ground rod driving with electric utilities.
The BR67120 And BR67130, featuring
the T-type handles and the standard feet,
are medium-duty tools for work in the 7090 lb. class. They are highly productive
in utility construction, street maintenance,
repair of water and gas mains and general contracting jobs.
• Lightweight and powerful general purpose
tools
• Use for curb and sidewalk work, asphalt
cutting and ground rod driving
• Utilizes Stanley Easi-Ride™ foot, designed
to absorb and control tool-bit bounce to
reduce operator fatigue
• Available with anti-vibration handles
• A lower noise level than a pneumatic breaker.
• No tool exhaust
• Trouble-free diaphragm accumulator for
added blow energy
• Continuous lubrication
• Handles system back pressures up to 250 psi
• Strong tie-bolt design for durability
Hydraulic Flow:
Weight:
Length:
Width:
Connection:
Tool Bit Size:
Hydraulic Flow:
Weight:
Length:
Width:
Connection:
Altec P/N
8126-45130
4-6 gpm
37 lbs
22.5”
14”
3/8” Flush Face Quick
Disconnect Coupler
Stanley P/N
BR45130
Call Toll Free
1-877-GO ALTEC
12
Altec P/N
0360-60001
8126-67130
1-1/8”x6” or 1-1/4”x6”
8 gpm
67 lbs
27”
16”
3/8” Flush Face Quick
Disconnect Coupler
Stanley P/N
BR67120 1 1/8” hex
BR67130 1 1/4” hex
Fairmont Sign Post Driver and Puller
Sign Post Driver -- Fairmont
These sign post drivers have quick-change
front head design that accommodates several
different types of post adapters. Integral
feathering trigger for maximum control on
units with built-in control valves. These sign
post drivers are supplied with steel braided
whip hoses. (Couplers not included.) A
rechargeable accumulator provides easier
service and a longer life.
• Open- or Closed-Center hydraulic System
• Flow range of 5 - 8 gpm
P/N 9000-11183
Fairmont 11183
P/N 9000-11186
Fairmont 11186
P/N 9000-11184
Fairmont 11184
P/N 9000-11187
Fairmont 11187
P/N 9000-11185
Fairmont 11185
P/N 9000-11188
Fairmont 11188
Sign Post Driver Accessories
P/N 9000-49532
Fairmont 49532
P/N 9000-49533
Fairmont 49533
P/N 9000-49534
Fairmont 49534
P/N 9000-41039
Fairmont 41039
P/N 9000-43041
Fairmont 43041
Internal Trigger, w/universal
post adapter
Remote on/off valve w/
universal post adapter
Internal Trigger, w/3.8”
round post adapter
Remote on/off valve w/3.8”
post adapter
Internal Trigger, w/2.13”
square post adapter
Remote on/off valve w/2.13”
square post adapter
3.8 inch round head adapter
Universal head adapter
2-1/8” square head adapter
Drive cap for 2” round post
Post adapter 1-13/16” round
Heavy-Duty Sign Post Driver -- Fairmont
This heavy-duty sign post driver is ideal for DOT
and street departments. This driver is designed
to be boom-mounted.
• 3/4” diameter lifting eye
• 12” whip hoses included
• Flow range of 7 - 9 gpm
• Operating pressure of 1,000 - 2,000 psi
• Open and closed center hydraulic system
P/N 9000-42234
Fairmont 42234
Sign Post Puller -- Fairmont
This sign post puller uses serrated jaws or
wraparound, high strength alloy chain. This
puller is faster and easier than conventional
manual methods. Use this sign post puller to
pull almost any post size and shape.
• Open-Center hydraulic system
• Lifting capacity of 9,800 lb.
• Flow range of 4 - 6 gpm
• Operating pressure 1,000 - 2,000 psi
• Weighs 70 lbs.
P/N 9000-42237
Fairmont 42237
Fairmont Rock Drill and Chipping Hammer
This innovative rock drill has a built-in
air compressor that blows dust out of
the hole. This exclusive, cost-effective feature eliminates the need for
hook-up to an air compressor or water
supply. With adjustable drill rotation
speed, it adapts precisely to varying material hardness. Its hydraulic
power source generates less noise
than that of a pneumatic.
The new chipping hammer is more powerful and
quieter than comparable
pneumatic tools. The chipping hammer is lightweight
enough,12 lbs., for horizontal use, and compact
enough to work in tight spaces.
• Weighs 44 lbs.
• Drills holes up to 2 1/2” in diameter, and 10’ deep.
• Vibration isolated and cushioned handles reduce
operator fatigue.
• Uses drills with 7/8” x 4 1/4” shanks.
• Heat insulated, anti-vibration comfort handle.
• Fast, efficient disassembly, maintenance.
• Vertical or horizontal operation design.
• Uses tools with 3/4” x 2” shanks.
P/N 9000-00944
P/N 9000-00912
Fairmont HRD44
Fairmont HCH12
13
Fairmont Ground Rod Drivers and Pole Puller
This pole puller works in confined areas,
next to buildings, or out in the open.
With a lifting capacity of 56,000 lbs. this
pole puller is great for heavy-duty construction. Works on either an open or
closed-center hydraulic system. Comes
standard with a 5/8” proof-certified 6 ft.
alloy chain.
These ground rod drivers drive various size
ground rods and can be used with single
or stacked rods. A reversible on/off valve
allows these drivers to be used on an open
or closed-center system. Drivers come
with built-in dual carrying handles and a
built-in lifting eye. Available with a 1” or
5/8” diameter opening.
• Flow range of 5 - 8 gpm
• Maximum input pressure 2,000 psi
• Flow range of 4 - 15 gpm
• Operating pressure of 300 - 2,800 psi
P/N 9000-11192
P/N 9000-11193
P/N 7010-69005
Fairmont HRD-58
Fairmont HRD-1
Fairmont H4910A
Stanley Ground Rod Drivers & Pole Puller
Capacity: 1/2” - 5/8” rod or 3/4” - 1” rod
Input flow range: 7 - 9 gpm
Input pressure: 1,500 - 2,000 psi
Weight: 52 lbs.
Length: 25”
Width: 16”
Input flow range:
Input pressure:
Weight:
Length:
Width:
The Stanley GD50 Ground Rod Drivers drive
1/2 to 1 inch rod from the top of the rod. A
valve, in-line on the hoses, permits control
of the GD50 while it is slung to the top of the
rod. Stanley GD50 features are:
• Top driving
• Long side handles give the operator
control during the driving process
• In-line valve in the 8-ft. hose whips gives
the operator ON - OFF control where he is
standing
• Rapid Fire
• Designed to remove flanged type sign
posts and irregularly shaped posts up to 8
in. wide
• Gripper jaws grasp any flanged post
Altec P/N
7010-69008
• 5-9 gpm (19-34 lpm) operating range.
• In-line valve on hoses for ON/OFF control.
• Assist handles.
• Lifting eye.
• HTMA quick disconnect couplers.
5 - 9 gpm
1,500 - 2,000 psi
52 lbs.
25.5”
10.0”
Altec P/N
9000-99427
1/2”- 5/8” rod
Stanley P/N
GD50132RF
Altec P/N
9000-994271
1/2” & 5/8” rod
Stanley P/N
GD50132-RS
9000-99428
3/4”- 1” rod
GD50133RF
9000-994282
3/4” & 1” rod
GD50133-RS
Call Toll Free
1-877-GO ALTEC
14
Stroke:
Pull Force:
Pressure:
Flow Range:
Weight:
Width:
Height:
8 in.
9,800 lbs.
2,000 psi
3 - 9 gpm
62 lbs.
12.75”
18.75”
Stanley P/N
PP10100
Fairmont Submersible Pumps
Submersible Water Pumps
These submersible pumps are compact and lightweight.
The carrying handle makes it easy to transport, move, lift
and lower. These pumps can run dry without damage for
longer working life. An open or closed center hydraulic
system can be used to run these pumps. These pumps
are also self-priming.
P/N 9000-42191
2” Submersible
up to 275 gpm
Fairmont H4665A
P/N 9000-42190
2 1/2” Submersible
up to 400 gpm
Fairmont H4660B
Submersible Trash Pump
These submersible trash pumps are lightweight and durable. These pumps can be run dry without damage. The
carrying handle makes it easy to transport, move, lift, and
lower.
P/N 9000-49333
3” Submersible
3/8” opening
Fairmont H4630
P/N 9000-49334
3” Trash Pump
Fairmont 49334
P/N 9000-42192
4” Trash Pump
Fairmont 42192
Stanley Submersible Pumps
• Pumps up to 250 gpm at a 10 ft. head
• Ideal for manholes
• Moves solids up to 5/16 in.
• Affordable alternative to large, heavy gas or
electric pumps
• Can run dry without damage
• Designed for use in confined, narrow
openings
• Pumps up to 300 gpm at a 10 ft. head
• Mixed-flow type cast iron impeller reduces
wear from abrasive fluids
• Can run dry without damage
Altec P/N
8126-20531
Stanley P/N
SM2053101
Altec P/N
8126-21511
Stanley P/N
SM2151101
Altec P/N
7050-00344
7050-00345
7050-00346
Stanley P/N
02183
05133
05135
Accessory Description
Fire hose w/pin lug, 25’
2 1/2” thread adapter for sump pump to fire hose
Spanner wrench for pin lug coupler
The SM50 Water Pump, built for high
capacity pumping of vaults and manholes,
is a submersible, centrifugal type pump
that requires no priming. The motor is a
contaminant-tolerant gear motor uniquely
designed for continuous high-speed operation. A series of seals on the drive shaft
effectively keep hydraulic fluid and pumped
water where they belong while allowing the
pump to run dry without sudden seal failure.
This pump can draw water to a depth of
3.5 inches and pumps up to 3/8 in. solids
at 375 gpm.
Altec P/N
9700-40138
Stanley P/N
SM50100
15
Fairmont Power Units
Fairmont’s portable, dependable hydraulic power unit features an easy starting and dependable Honda 6.5 HP OHV
engine that produces an output flow of 5 gpm. Works great
for powering impact wrenches, drills,
water/trash pumps, post hole augers,
chain saws and pruners. This power
unit is lightweight and fits easily in
most vehicles. To save fuel, a poweron-demand feature is standard.
Fairmont’s portable high-performance power unit with a
20 HP Honda OHV engine is designed for long hours of
continuous use. Hydraulic flow is variable from 5 to 10
gpm. Featuring 10 inch tires and
a folding handle, this power unit is
easy to maneuver at the job site and
is compact for storage. The openframe design provides easy access
for maintenance and service.
Specifications:
Horse power:
Hydraulic System:
Rated Flow:
Rated Pressure:
Fuel:
Hyd. Oil Capacity:
Length:
Width:
Specifications:
Horse power:
Hydraulic System:
Rated Flow:
Rated Pressure:
Fuel:
Hyd. Oil Capacity:
Length:
Width:
6.5 @ 3,600 rpm
Open-Center
5 gpm
1,700 psi
0.95 gal gas
1.8 gal
30 in.
17 in.
P/N 9000-45835
Fairmont F07
20 @ 3,600 rpm
Open-Center
4 - 10 gpm
2,000 psi
2.3 gal gas
3.1 gal
34 in.
29 in.
P/N 9000-45895
Fairmont F20
Fairmont Miscellaneous Hydraulic Tools
Portable Alternator
This portable alternator provides instant electric power for
lighting, heaters, and most electrically driven equipment.
Operating off hydraulic systems with flow rates from 8 - 12
gpm this alternator has a capacity
of 3,500 watts. This Fairmont alternator is circuit breaker protected
with two 120 and one 240 AC volt
outlets.
Specifications:
Hydraulic System: Open and closed
center
Capacity:
3,500 Watts
Flow Range:
8 - 12 gpm
System Pressure: 2,500 psi
Weight:
63 lb.
Height:
14 in.
Width:
8.5 in.
P/N 9000-42276
Fairmont H6635
Cut-Off Saw
This Fairmont cut-off saw easily cuts concrete, stone, or
steel when equipped with the appropriate blade. (Blade
not included.)
Specifications:
Hydraulic System: Open-center
Operating Pressure:1,000 - 2,000 psi
Cutting Capacity: 5.25 in. with 14 in. blade
Blade Speed:
4,100 rpm at 8 gpm
Blade Diameter:
14 in. max.
Arbor Shaft Dia.:
1 in.
Flow Range:
5 - 8 gpm
Weight:
21 lbs.
P/N 9000-42252
P/N 9000-42993
P/N 9000-42994
Dynapress® Hydraulic Intensifier
This small, compact intensifier operates 10,000 psi remote
head tools. Operates on either open or closed center
systems without making any
changes to the tool. Supplied
with pressure and return high
pressure screw-type couplers.
Also supplied with convenient
foldable carrying handle, and can
be permanently mounted.
Specifications:
Low Pressure Side:
Input Pressure:
1,000 - 2,200 psi
Input Flow:
4 - 8 gpm
Max. Back Pressure:
200 psi
Port Sizes:
3/4 - 16 SAE O-ring
High Pressure Side:
Output Pressure:
10,000 psi
Output Flow:
35 cu-in/min
Relief Valve Setting: 10,000 psi
Port Sizes:
1/4 - 18 NPSM
Fast Advance Flow: 320 cu-in./min
P/N 9000-49830
Cut-off Saw
Metal Saw Blade
Concrete Saw Blade
Call Toll Free
1-877-GO ALTEC
16
Fairmont HB10
Hydraulic Reel Ball Stops and Swivels
Hydraulic Reel Ball Stop
These hose stops are recommended with spring rewind reels
and 4-way roller assemblies.
Each stop is easily assembled
with the fasteners provided,
without any special tools. These
ball stops are two-piece molded
plastic spheres, custom-drilled to
the size you specify.
P/N 276-90011
P/N 276-90051
Hydraulic Reel Ball Swivel
• 1/2” swivel joint
• 90 degrees - male to female
• Made from steel
• Rated to 3000PSI
P/N 276-99034
For dual 3/4” hose
For 3/8” and 1/2” hose
Reels
Hose Reels
Because rewind power is self-contained, spring rewind
reels are extremely versatile. No power connections are
required and the reels may be installed in almost any position and on all types of equipment. These reels rewind hose
automatically when the hose is pulled to release the ratchet.
The ratchet provides interval locking or may be detached
for constant tension operation. A declutching hub arbor
prevents damage to the spring from reverse winding. The
heavy-duty spring operates through thousands of cycles
without power loss. Each unit is equipped with rollers to
protect the hose as it extends and retracts from the reel.
Each hose reel is equipped with two swivel joints, allowing
the use of two hoses simultaneously. Models are available
to handle a variety of hose sizes and lengths.
Reels
P/N 276-90002
P/N 276-90058
Reel holds 50’ of 1/2” hose and 65’ of 1/4”
Hose not included
Reel holds 50’ of 3/8” and 1/2” hoses
Hose and ball stop included
Reel Hose Assembly
P/N 271-39058
25’ of 1/2” hose
P/N 271-39003
50’ of 1/2” hose
P/N 271-29007
P/N 271-29027
25’ of 3/8” hose
50’ of 3/8” hose
17
Hydraulic Tool Accessories
Non Conductive Tool Hose
HTMA Couplers
Twin line, certified 3/8” non conductive tool hose assembly.
Available in three standard lengths 8-,
10- and 25 ft. Special order lengths
are also available.
This female HTMA coupler is 3/8” NPTF internal thread.
The maximum operating pressure is 3,000 psi.
P/N 271-29444
P/N 271-29457
P/N 271-29542
8’ Length
10’ Length
25’ Length
Please contact your Altec service representative at
1-877-GO ALTEC for special order lengths.
P/N 9000-41777
Fairmont F020195K
This male HTMA coupler is 3/8” NPTF internal thread. The
maximum operating pressure is 3,000 psi.
P/N 9000-41780
Fairmont F020198K
High Pressure 10,000 PSI Hose Assembly
Available in standard lengths:
P/N 9000-50026
P/N 9000-50027
P/N 9000-50028
P/N 9000-50029
6 Ft
10 Ft
15 Ft
20 Ft
Twinned Hose
New technology allows two
hydraulic hoses to be joined
(twinned), during the manufacturing process through vulcanizing.
The “twinned hose” will always
remain parallel, preventing the
hoses from “flopping” around.
P/N 9000-50030
P/N 9000-50031
25 Foot Assembly
50 Foor Assembly
Quick Release Coupling
• Spillage .008cc
• Interchangeable
• Special profile eurothane seal
• Special design on seal eliminates
dirt inclusion
• Coupler allows perfect connect
under highest pressure without any seal extrusion
• Eliminates leakage at lowest pressure (dripless)
• 3/8” body size coupler with 3/8” female pipe thread at
each end
• 10GPM unit withstands pressure up to 3625 PSI
• HTMA Hydraulic Tools Association Standard
• Complete unit (male/female)
P/N 9000-20132
Quick Release Coupling, Complete
Quick Disconnect Couplers
Dust Cap & Dust Plugs
Protect your couplers and
adapters from dust and debris
with these convenient dust
caps and plugs. The dust cap
fits the female end, and the
dust plug fits the male end.
P/N 9000-20144
P/N 9000-20145
Dust Cap
Dust Plug
Chuck Adapter for Impact Tool
Adapts a 1/2” square drive impact to be used with drill
bits up to 1/2” shank.
P/N 9700-13302
Set of 3/8” HTMA flush face couplers.
Includes both the male and female
couplers.
P/N 356-20132
Swivel Adapters
Hose assemblies can be applied
directly to the tool without the use
of body assemblies or nose pieces,
eliminating the quick-disconnect
feature by ordering one of each.
P/N 274-01155
P/N 7010-68821
3/8” x 3/4”
3/8” x 9/16”
Hydraulic Tool Replacement Parts
Fairmont Impact Wrench Replacement Parts
Fairmont Tamper Replacement Parts
Seal kit
Anvil
Link for trigger
Seal kit for tamp with valve
Seal kit for tamp without valve
Hose clamp
Ram
Packing nut
9000-99877
9000-49272
9000-48313
Fairmont Long-Reach Chainsaw Replacement Parts
Seal kit
Sprocket
9000-48254
9000-99890
9000-39009
9700-06663
9000-99898
9000-99807
9000-14651
Fairmont Crimper Replacement Parts
Seal kit for model LPK1230
Seal kit for model LPK1550
Seal kit for model H1216
Seal kit for model 48735/48730
Seal kit for model 48750
9700-14415
9000-49358
9700-14407
9700-14416
9700-14414
Stanley Impact Wrench Replacement Parts
Stanley Tamper Replacement Parts
Seal kit for model ID04
Seal kit for model ID07
Seal kit for model IW08
Seal kit for model IW09
Seal kit for model with valve
Seal kit for model without valve
Ram kit with nose guard and seals
Hose guide
8855-32328
9000-60791
360-29003
360-29004
Stanley Long Reach Chainsaw Replacement Parts
Seal kit for CS23/26
360-09010
360-39004
360-39007
360-39001
360-09050
Stanley Crimper Replacement Parts
Seal kit for model CT10
Seal kit for model CT15
8126-06538
9700-14402
19
Altec Direct offers a wide range of replacement parts for these Greenlee/Fairmont products.
Please call your Altec Service representative at 1-877-GO ALTEC for more information.
Contact your nearest Altec location for assistance with all part and accessory needs.
1-877-GO ALTEC