620 Series Medium Bi-Pin Fluorescent Quickwire

Transcription

620 Series Medium Bi-Pin Fluorescent Quickwire Lampholders
for T8 and T12 Lamps
UL File. No. E36983
CSA File No. LR11209
Rated 660W - 600V
620A
Thin quickwire fluorescent lampholders are molded in white thermosetting urea, with
black phenolic available to order. Quickwire pressure terminals of high-strength brass
alloy accept #18 AWG solid, topcoat or twisted and tinned stranded leads. Silverplated contacts are available by special order. Consult factory for minimums required.
Lampholders are available with various features for a wide range of mounting methods.
Each contact features a double-contact connection, permitting a jumper connection for
rapid start circuits. Screws and nuts can be supplied separately or can be inserted to
order. See hardware chart below for ordering options. Consult the mounting chart and
dimensional drawings for information on variations in mounting methods. Lampholders
and socket combinations available.
•
•
•
•
Features quickwire terminals
Permits jumper connection for rapid-start circuits
Circuit interrupting type featuring disconnect
Three different mounting configurations available
620A
11/32
1
Catalog Number Description
620A
Screw and nut, and/or 18 gauge
mounting grooves
Part Number
Catalog Number/Description
F0960000A005-M
620A NASB
F0960000A006-M
620A NASB 6-32 x 1/2”
F0960000A007-M
620A LNLS
5/32
1- 1/8
0.058
0.053
2- 3/8
1/16
11/32
5/8
Hardware Ordering Options
Description
Ordering Code
Less nuts, less screws
LNLS
Nuts inserted, screws in bulk
NASB
620 Series slotted screws are 6-32 x 5/8” length, part #18-59134-625.
620 and 630 Series PAL nuts are 6-32 thread gauge, part #019-12632.
Phillips head screws are available by special order.
Screws and nuts are not included, unless requested.
Lampholders are suitable for use in fixtures designated for damp or wet locations.
Add hardware code as suffix to catalog number i.e., 620A-NASB.
A.L.P. Lighting Components, Inc.
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
1- 15/32
13/16
UL File No. E36983
Rated 660W - 600V
630A
630A-1
Thin quickwire fluorescent lampholders are molded in white thermosetting urea, with black
phenolic available to order. Quickwire pressure terminals of high-strength brass alloy accept
#18 AWG solid, topcoat or twisted and tinned stranded leads. Silver-plated contacts are
available by special order. Consult factory for minimums required. Lampholders are available
with various features for a wide range of mounting methods. Each contact features a doublecontact connect, permitting a jumper connection for rapid start circuits. Screws and nuts can
be supplied separately or can be inserted to order. See hardware chart on next page for
ordering options. Consult the mounting chart and dimensional drawings for information on
variations in mounting methods. Lampholder and socket combinations available.
•
•
•
•
Permits jumper connection for rapid-start circuits
Features quickfire terminals
13 different mounting configurations available
Part Number
F1020000A001-M
630A NASB (018-59140-375 SCR)
F1020000A002-M
630A
F1020000A003-M
630A NASB (018-59134-375 SCR)
F1020000A006-M
630A NALS
F1020001A001-M
630A-1
F1020001A008-M
630A-1 NALS
F1020003A003-M
630A-3 LNLS
F1020003A004-M
630A-3 NALS
F1020005A002-M
630A-5 NALS
F1020051A002-M
630A-51 LNLS with 11” #18 AWM 1015 topcoat leads strip 7/16”
F1020051A018-M
630A-51 NASB with 9” #18 AWM 1015 strip 1/2”
F1020052A005-M
630A-52 with 9” white #18 AWM 1015 strip 1/2”
630A
11/32
1
2- 1/16
1- 3/16
5/16
23/32
630A-1
1
11/32
1- 3/4
Catalog Number
Description
630A
Screw and nut
630A-1
18 gauge panel mount
630A-3
20 gauge panel slot
630A-5
Full base
630A-51
Disconnect lead and screw nut
630A-52
18 gauge panel mount disconnect lead
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
2- 1/16
0.043
0.047
1
+.005
-.005
1- 1/4
23/32
Description
Ordering Code
LNLS
Nuts in bulk, screws in bulk
NBSB
Nuts inserted, less screws
NALS
NASB
Nuts and screws inserted
NASA
630A
1- 3/16
620 and 630 Series pal nuts are 6-32 thread gauge, part #019-12632.
630A-1
630A-3
1
5/16
1
630A-5
1- 3/4
1- 3/4
0.043
0.047
0.043
0.047
1
+.005
-.005
1
+.005
-.005
1- 1/4
1- 1/4
630A-51
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
630A-52
1
631 Series Medium Bi-Pin Quickwire Fluorescent Low Profile Lampholders
UL File. No. E36983
Rated 660W - 600V
631A-1
These thin quickwire lampholders are molded in white thermosetting urea, and also are
available in black to order. Quickwire pressure terminals of high-strength brass alloy permit
easy, positive wire connection. Terminals will accept #18 AWG solid, topcoat or twisted
and tinned stranded leads. Silver-plated contacts are available by special order. Consult
factory for minimums required. Circuit interrupting disconnect available on the 631 Series.
Variations available for screw and nut mounting or slide-on mounting grooves.
•
•
•
Quickwire terminals for easy wire connection
Screw and nut or panel mounting available
Terminals accept a variety of leads
Part Number
F104A1LNLS01-M
631A-1 LNLS
F1040000A002-M
631A NASB
F1040000A005-M
631A NASB (018-59140-375 SCR)
F1040000A006-M
631A LNLS
631A-1
63/64
Description
Ordering Code
LNLS
NBSB
NALS
NASB
NASA
11/32
1- 13/16
15/16
0.053
0.058
5/16
47/64
1- 5/32
Table of Mounting Methods
631A
Screw and nut
631A-1
18 gauge panel mount
PAL nuts are part #019-12632.
Add hardware code as suffix to catalog number, i.e., 631A-NASB.
631A
11/32
63/64
1- 13/16
15/16
5/16
1- 5/32
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
47/64
Series 635, 636 Medium Bi-Pin Quickwire Fluorescent Butt-On Lampholders
For T8 and T12 Lamps
UL File No. E36983
635A
These butt-on lampholders are molded in black phenolic or white thermosetting urea,
and are supplied with 9” #18 AWM 1015 105°C wire. Other types and lengths are
available. Lampholders are available with tempered steel snap-in springs or 4-36
tapped holes, or 0.140” diameter slip holes. Mounting screws sold separately, please
specify. Leads may be brought out straight or from rear for flush mounting.
•
•
•
Either snap-in springs, clearance hole, or tapped hole mountings available
Black phenolic or white thermosetting urea composition
Part Number
F106635A0002-M
635A with 9” #18 AWM 1015 topcoat leads strip 1/2”
F106635A0005-M
F106635A0006-M
F106635A0013-M
635A 6” #18 AWM 1015 strip 9/16”
F106635A0026-M
635A with 9” #18 AWM 1015 strip 1/2”
F106635A5103-M
635A-51 with 9” #18 AWM 1015 black and white, leads strip 3/8”
NOTE: Disconnect lead to be white “A” lead black and “B” lead white
F106636A0008-M
636A with 9” #18 AWM 1015 leads strip 1/2”
F106636A0018-M
636A with (1) 10” white (‘A’ lead) #18 AWM 1015 topcoat lead strip 7/16”
& (1) 6- 1/2” white (‘B’ lead) #18 AWM 1015 lead strip 3/16”, less screws
F106636A0019-M
636A with (1) 5-1/2” white (‘A” lead) #18 AWM 1015 topcoat lead strip 7/16”
& (1) 14- 3/4” white (‘B’ lead) #18 AWM 1015 lead strip 3/16”, less screws
636
4-36
Catalog Number
Catalog Number
Color
Rated 660W - 600V Rated 660W - 250V
Mounting Methods
635A
635A-101
White
Snap spring, screws not
necessary
635A-51
635A-151
White
Snap spring with disconnect,
screws not necessary
636A
635A-101
White
4-36 tapped holes, screws
optional
635
1- 1/4
31/32
dimensional data for 635 & 636 Series
1- 7/32
35/64
7/16
5/32
“A” Lead
White unless
otherwise specified
31/32
suggested cutout for 635
Snap Spring Series
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
“Disconnect” Lead Blue
unless otherwise specified
“B” Lead
Black unless
otherwise specified
645 Series Medium Bi-Pin Fluorescent Butt-On Lampholders
UL File No. E36983
Rated 660W - 600V
645A-2
These fluorescent butt-on lampholders, molded of white thermosetting urea, come
with high-strength brass alloy quickwire pressure terminals that accept #18 AWG solid,
topcoat or twisted and tinned stranded leads. Silver-plated contacts are available by
special order. Consult factory for minimums required. Lampholder features release
slots at each connection. Multiple terminal slots permit double contact connection at
each contact, allowing a jumper connection for rapid start circuits. Available with center
hole for butt-on mounting, with side slots, mounting grooves, or mounting brackets.
Consult chart for variations.
•
•
•
Designed for fast wiring
High-strength alloy quickwire terminals
Options allow many mounting configurations
645A-1
1- 3/8
Catalog Number
Mounting Variations
645A-1
With 0.150 diameter hole in center
645A-2
With #8-32 tapped hole in center
645A-8
Slide-on mounting tabs in body made to
engage formed lancings in fixture plate
645A-27
With 0.038 mounting grooves
Part Number
F1100001A005-M
645A-1 externally shunted (side draw)
F1100001A002-M
645-1
F1100002A002-M
645A-2 (side draw with #8-32 tap)
F1100008A007-M
645A-8
F1100027A002-M
645A-27
F1100027A003-M
645A-27 externally shunted
11/32
9/16
1- 7/16
13/32
5/32
645A-8
11/32
1- 3/8
1/8
1- 15/32
1/4
9/16
9/32
1/2
13/32
1/8
1- 17/32
645A-27
9/32
645A-2
1- 3/8
1- 3/8
9/16
9/16
0.043
0.038
13/32
13/32
3/16
1- 23/64
1- 1/2
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
#8/32
649 Series Medium Bi-Pin Fluorescent Lampholders - Low Profile
For T8 Lamps
UL File No. E36983
Rated 660W - 600V
649A
These thin quickwire lampholders are molded in white thermosetting urea. Available
in black to order. Quickwire pressure terminals of high-strength brass alloy permit
easy, positive wire connection. These terminals will accept #18 AWG solid topcoat or
twisted and tinned stranded leads. Silver-plated contacts are available by special order.
Consult factory for minimums required. Variations available for screw and nut mounting
or slide-on mounting grooves.
•
•
•
Quickwire terminals for easy wire connection
Screw and nut or panel mounting available
Terminals accept a variety of leads
Part Number
F1140000A001-M
649A NASB
F1140000A003-M
649 NBSB
F1140000A004-M
649A
F1140000A012-M
649A NASB
F11400000001-M
649A NALS
649A-1
11/32
63/64
1- 17/32
Description
Ordering Code
Less Nuts, less screws
LNLS
NBSB
NALS
NASB
NASA
37/64
25/64
23/32
649A
11/32
63/64
Table of Mounting Methods
649A
Screw and nut
649A-1
Screw and nut
Add hardware code as suffix to catalog number i.e., 631A-NASB.
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
1- 17/32
21/32
5/16
23/32
650 Series Medium Bi-Pin Fluorescent Starter Base Holder Sockets
UL File No. E41860
Rated 660W - 250V
650-11
These starter base holder sockets, molded in black phenolic or white urea, are supplied
with high-strength brass alloy quickwire terminals for easy wire insertion. Quickwire
termination will accept #18 solid or topcoat wire. Used for independent mounting or in
combination with our catalog #630-A series. This combination will provide quickwire
features to both a starter socket and a lampholder.
650-1
Starter sockets with wires attached can be supplied with #18 AWG stranded, topcoat,
or prebond leads. Consult the chart and dimensional drawings for information on the
variation in mounting methods available. The suffix number must be added to the
catalog number when ordering. Order mounting screws separately.
Part Number
32/32
7/8
7/16
1- 1/4
F11600030016-M 650-3 No leads
7/16
F11600090018-M 650A-9 No leads - white
F11600110001-M 650-11 red #18 AWM 1015 topcoat (1) 7” (1) 26” lead strip 3/8”
F11600110004-M 650-11
F11600120010-M 650-12 Using PBT material for the fiber
F11600260028-M 650-26 Note: use -14 bracket mounted at 90° angle
F11600260030-M 650-26 Note: use -14 bracket mounted at 90° angle
F1020001A009-M 630A-1 / 650 combo (1) 5-1/2” #18 gauge 1015 solid black lead pushin wire lead to be inserted into right side wire port of 650
F1020001A011-M 630A-1 / 650 combo inserted, joined with black #18 AWM 1015
solid lead between the devices, (1) with 18” and (1) 6”
630A with
650-6 combo
Table of Mounting Variations
-3
Flat metal bracket - two holes tapped 6/32”
-9
U-shaped metal spring for snap-in attachment. 1.350” height
-11
Shallow U-shaped bracket. Height 37/64” two holes tapped 6/32”
-12
Two 9/64” diameter clearance holes
-26
-14 bracket mounted on 90° angle
Mounting Variations
650-9
650-3
1- 1/4
650-11
1- 7/16
31/32
ROSCA 6/32
7/8
.150 D.
ROSCA 6/32
7/8
1- 7/16
1- 1/4
1- 7/16
1- 1/4
7/16
650-26
31/32
1- 11/32
7/8
37/64
7/16
1- 13/16
31/32
1- 1/4
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
659 Lead Series Miniature Bi-Pin Fluorescent Lampholders
For T5 Lamps
UL File No. E36983
Rated 75W - 250V
These lampholders, molded of black phenolic or white urea, are ideal for mirror case
lighting, showcase lighting, or any other confined space applications. High-strength
brass alloy contacts, designed for firm lamp grip, to protect against vibration. Supplied
with 6” #18 AWM 1015 105°C or #18 topcoat wire leads, with other types and lengths
of wire available to specific order. Lampholders are available with various mounting
brackets for front or back mounting, or as butt-on mounting, without a bracket. Catalog
#659-black, catalog #659A-white. Add the suffix number from the table listing to the
catalog number when ordering.
659 Series Front Mount Brackets
Part Number
F1200001A008-M
659A-1 tapped 6-32 with 6” #18 AWM 1015 strip 5/8”
F1200001A033-M
659A-1 tapped 6-32 with 9” #18 AWM 1015 strip 3/8”
F1200001A042-M
659CA-1 with one contact crimped without wire and put into housing and
one 23” #22 AWM 1007-1569 white lead cut blunt
F1210001A001-M
659A-6V-1 with front mount bracket and 9” #18 AWM 1015 black and
white topcoat strip 3/8”
Cat. No.
A
B
C
D
1
17/32”
19/32”
11/32”
6-32
659A-1
Front Mount
659A-1
Front Mount
5/8
3/4
17/32
19/32
659 Series Back Mount Brackets
Part Number
23/64
659A-2
Back Mount
F1210002A001-M 659A-6V-2 with 9” #18 AWM 1015 black & white topcoat leads through strip 3/8”
F1210002A007-M 659A-6V-2 with 9” #18 AWM 1015 black & white topcoat leads through strip 3/8” packed 100/bag
F1201184A005-M 659A-1184 with 9” #18 solid AWM 1015 strip 1/2” not through
F1201184A037-M 659A-1184 with 19” black & 5” white #18 solid AWM 1015 strip 1/2” not through
659A-2
Back Mount
23/64
5/8
F1211341A001-M 659A-6V-1341 9” #18 AWM 1015 black & white topcoat leads through strip 3/8”
F1211383A001-M 659A-6V-1383 9” black & white #18 AWM 1015 topcoat strip 1/2”
F1211385A002-M 659A-6V-1385 with 8” #18 AWM 1015 topcoat leads through bracket strip 3/8”
3/4
F1211385A004-M 659A-6V-1385 with 15” #18 AWM 1015 topcoat leads through bracket strip 3/8”
5/32
F1211386A001-M 659A-6V-1386 with 9” black & white #18 AWM topcoat leads strip 1/2”
F1211387A001-M 659A-6V-1387 with 9” black & white #18 AWM 1015 topcoat leads strip 3/8”
F1211387A002-M 659A-6V-1387 tapped 6-32 with 9” #18 AWM 1015 topcoat leads strip 3/8”
Cat. No. A
B
C
2
1- 1/32”
25/32”
6-32
1184*
1- 1/32”
25/32”
6-32
1341
1- 1/32”
25/32”
0.140 Dia.
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
11/32
#6-32
25/32
660 Series Low Profile Medium Bi-Pin Quickwire Lampholders
UL File No. E36983
Rated 660W - 600V
660A-13
Shunted
These lampholders, molded in white thermosetting urea or black phenolic, feature
quickwire pressure terminals with recessed wire wells to insulate against shorting.
High-strength brass alloy quickwire contact accept #18 gauge solid, topcoat or twisted
and tinned stranded leads, and are available with a wide variety of mounting methods.
The multiple terminal slots permit a double contact connection at each contact point,
allowing a jumper connection for rapid start circuits. Silver-plated contacts are available
by special order. Consult factory for minimums required.
•
•
•
•
Knife edge contact design ensures positive “cut-in” lamp/pin contact
Available for rapid start, instant start, program start, and pre-heat ballasts
Performs better during catastrophic end-of-life (EOL) lamp failure
Thermoset urea housing resists heat distortion up to 132°C*
*Catastrophic end-of-life failure can generate temperatures at that lamp end far higher that the
deformation point of any plastic lampholder. A.L.P. recommends installing ballasts designed to
provide integral end-of-life protection.
Catalog/Part
Number
Shunted/
Non Shunted
Face to Back Mounting
Thickness
660A-13
F1220013A008-M
Non Shunted
11/32”
Combo 20 gauge upper and 18 gauge lower grooves
for slide-on mounting in open-back socket bars
660A-13SH
F1220013A010-M
Shunted
11/32”
for slide-on mounting in open-back socket bars
660A-13-NALS
F1220013A006-M
Non Shunted
11/32”
for slide-on mounting in open-back socket bars. Nuts
inserted, less screws
660A-13SH-NALS
F1220013A038-M
Shunted
11/32”
for slide-on mounting in open-back socket bars. Nuts
inserted, less screws
Suffix SH= shunted lampholders for use with instant start ballast.
Suffix NALS = Nuts inserted, less screws.
660A Non Shunted
660A Shunted
1
1
1- 21/32
1- 21/32
7/8
7/8
3/8
3/8
1
1- 1/4
1
1- 1/4
23/32
9/32
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
23/32
9/32
661A-100 Series Low Profile Medium Bi-Pin Fluorescent Lampholders
Straight-In For T8 and T12 Lamps
UL File No. E36983
Rated 660W - 600V
These lampholders, molded of white thermosetting urea, are supplied with straightin, double-edge contacts for positive lamp grip. High-strength brass alloy quickwire
pressure terminals accept #18 AWG solid, topcoat, or twisted and tinned stranded
leads. Silver-plated contacts are available by special order. Consult factory for
minimums required. Lampholders are available with #20 gauge and #18 gauge
mounting grooves. Consult chart for variations. 661A Series circuit interrupting type,
featuring disconnect design, is available upon special request.
•
•
•
•
Edge wipe contacts
Provides positive lamp grip
Mounting variations available
Part Number
F1240101A001-M
661A-101 externally shunted
F1240103A001-M
661A-103
F1240111A005-M
661A-111
F1240111A006-M
661A-111sh int. shunt
F1240112A011-M
661A-112 less nut, screw bag
Catalog
Number
Mounting Variations
661A-101
20 gauge top & bottom slots - no
nut slot
661A-103
20 gauge top 18 gauge bottom
slots - no nut slot
661A-111
20 gauge top and bottom slots with nut slot
661A-103
661A-103
1
7/8
1- 19/32
0.041
0.044
0.055
0.052
3/8
3/16
.990
1- 1/4
Ordering Code
LNLS
NBSB
NALS
Nuts inserted, screws in bulk NASB
23/32
661A-111
1
11/32
5/16
7/8
Description
11/32
5/16
1- 19/32
0.041
0.044
0.055
0.052
3/8
3/16
.990
1- 1/4
23/32
NASA
Add hardware code as suffix to catalog
number i.e., 661A-10-NASB.
661A-100 Series slotted screws are 6-32 x 3/8” length, part #018-59134-375.
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
11/32
661A-160 Series Medium Bi-Pin Fluorescent Lampholders
Floating Action For U-Shaped T8 and T12 Lamps
UL File No. E11033
Rated 660W - 600V
These lampholders, molded of white thermosetting urea, feature straight-in, doubleedge contacts for positive lamp grip. Quickwire pressure terminals are available with
#20 AWG and #18 AWG mounting grooves. Consult chart for variations. The 661A
Series circuit interrupting type, featuring disconnect design, is available upon special
request.
•
•
•
•
Edge wipe contacts
Provides positive lamp grip
Mounting variations available
Part Number
F1240168A002-M
661A-168
F1240171A001-M
661A-171
F1240175A001-M
661A-175
Catalog Number
Mounting Variations
661A-168
18 gauge top and 20 gauge
bottom slots - no nut slot
661A-171*
20 gauge top and bottom slots with nut slot
661A-175
661A-168
1
11/32
5/16
7/8
Less nuts, less
screws
LNLS
Nuts in bulk,
screws in bulk
NBSB
Nuts inserted,
less screws
NALS
Nuts inserted,
screws in bulk
NASB
Nuts and screws
inserted
NASA
number i.e., 661A-150S-NASB.
661A-160 Series slotted screws are 6-32 x 3/8” length, part #018-59134-375.
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
3/16
0.044
0.041
* 15,000 piece minimum required
Ordering Code
1- 19/32
0.055
0.052
20 gauge top, no bottom slot no nut slot
Description
661A-168
.990
1- 1/14
1- 11/32
3/8
23/32
668 Series Quickwire Miniature Bi-Pin Fluorescent Lampholders
For T5 Lamps
UL File No. E36983
Rated 75W - 250V
668
These lampholders, molded of black phenolic or white urea, are ideal for mirror case
lighting, showcase lighting, or any other confined space applications. High-strength
brass alloy contacts, designed for firm lamp grip, are supplied to protect against
vibration. Supplied with quickwire terminals that will accept #18 solid, topcoat or
twisted and tinned stranded wire. Catalog #668-black, catalog #668A-white. These
lampholders are available with various mounting brackets for front or back mounting,
or as butt-on mounting, without a bracket. Add the suffix number from the table listing
to the catalog number when ordering.
•
•
•
668
13/16
3/8
Ideal for mirror case and display lighting
Firm lamp grip prevents vibration
Variety of mounting brackets available
25/32
Part Number
F12800000001-M
668 Front mounted bracket
F1280000A001-M
668A Front mounted bracket
F1280001A001-M
668A-1 Front mounted bracket
Catalog Number
A
B
C
D
668
19/32”
9/15”
1/16:
0.0150
668-1
19/32”
9/16”
1/16”
6-32
680A Series Quickwire Fluorescent Circline Connector
For Use with High Voltage Instant Starting Transformers
UL File No. E36983
Rated 660W - 600V
680A
These connectors, molded in white urea, feature quickwire brass alloy contacts that
accept #18 AWG solid, topcoat, or twisted and tinned leads. Leads furnished on
request. Connector is available with body only or with mounting brackets. Used with
high voltage instant starting transformers.
•
•
•
For use with high voltage instant starting transformers
Contacts accept a variety of leads
Molded urea construction
680A
23/32
15/16
F1360000A001-M
680A
5/16
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
5/8
TRIBORO
660W 600V
Part Number
19/32
5/16
1/4
682 Series Medium Bi-Pin Fluorescent Lampholders - Standard Size
UL File No. E36983
Rated 660W - 600V
682A
Standard size lampholders molded of white thermosetting urea. High-strength brass
alloy quickwire pressure terminals accept #18 AWG solid, topcoat, or twisted and
tinned stranded leads. Multiple terminal slots permit double contact connection at each
contact, allowing a jumper connection for rapid start circuits. Silver-plated contacts
are available by special order. Consult factory for minimums required. Recessed wire
wells guide wire to positive locking with terminals, and completely enclose conductor
to insulate against shorts. Consult the chart and dimensional drawings for information
on mounting methods available.
•
•
•
Quickwire terminals accept a variety of leads
Permits jumper connection for rapid start circuits
Edge wipe contacts
Part Number
Catalog Number/
Description
F1380000A004-M
682A
F1380004A003-M
682A-4
F1380004A005-M
682A-4 NASB
F1380008A007-M
682A-8
F1380010A003-M
682A-10
682A
682A-4
1
11/32
1
2- 1/32
2- 1/32
5/32
11/32
5/32
1- 3/16
1- 3/16
0.042
0.044
3/8
Hardware Ordering Option
Description
Ordering Code
Less nuts, less
screws
LNLS
Nuts in bulk,
screws in bulk
NBSB
Nuts inserted,
less screws
NALS
Nuts inserted,
screws in bulk
NASB
Nuts and screws
inserted
29/32
1- 11/64
1- 3/8
23/32
1- 3/8
682A-8
682A-10
1
11/32
2- 1/32
1- 3/16
1- 9/32
number i.e., 682A-NASB.
Mounting Variations
Catalog Number
Panel Mount
682A
20 gauge
682A-4
6-32 screw and nut
682A-8
20 gauge with wide base
682A-10
18 gauge with wide base
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
1- 3/16
11/32
2- 1/32
1- 9/32
3/8
3/8
29/32
1- 11/32
1- 15/32
1
0.053
0.057
0.042
0.044
NASA
3/8
23/32
23/32
29/32
1- 11/32
1- 15/32
23/32
PAL nuts are part number #019-12682.
Lampholders are suitable for use in fixtures designated for damp and wet locations.
10T, 16 and 17 Series Medium-Base (E26) Phenolic Adapters
UL File No. E26302
Rated 660W - 250V
10T
The 10T Phenolic Flanged Adapter features a one-piece flanged body with standard
male screw shell and reinforcing ring. Molded of black phenolic or white urea, with
aluminum screw shell standard. Brass or brass-nickel plated shell available by special
order. Two holes spaced 1.275” on centers. Dimensions: 1-11/16” o.d. x 1-1/2” high.
Adapter is available with leads or eyelets for soldering. Standard leads are 6” #18
AWM 1015 105°C.
Fiber cover available upon request.
Catalog Number 16 Phenolic Adapter - Similar to catalog number 10T with a
unique new ratchet ring feature to prevent over-tightening. Reverse ratchet available
as special order.
Part Number
10A
F0060010T004-M 10T brass-nickel plated screw shell - no leads
1- 1/2
F0060010T024-M 10T brass-nickel plated screw shell with 7- 1/2” #18 XFF strip 1/2”
F0060010T036-M 10T brass-nickel plated screw shell with 8” #18 200°C SF-1
strip 3/8” with fiber leads exiting wireways in fiber cover
F0060010T055-M 10T adapter brass-nickel plated screw shell with 20” #18 1015
strip 5/8”
F0060010T059-M 10T brass-nickel plated screw shell - no leads (special plastic)
1- 9/32
1- 11/16
F0060010T060-M 10T brass-nickel plated screw shell - no leads
F00600160005-M #16 adapter brass-nickel plated screw shell with 6” #18
1015 strip 1/2”
17
F00600170002-M 17-2 brass-nickel plated screw shell with 3”/9” #18 200°C
SF-2 strip 1/2”
F00601130031-M 113 adapter brass shell with 15- 1/8”/14- 7/8” #18 1015 strip 3/16”
F00601130035-M 113 adapter brass shell with 4- 5/8” /4- 3/8” #18 1015 strip 3/16”
F00601130037-M 113 adapter brass screw shell - no leads
Catalog Number 17 Phenolic Adapter - One-piece phenolic body with standard male
screw shell with reinforcing ring molded of black phenolic or white urea. Aluminum
screw shell is standard. Brass or brass-nickel plated shell available to order. Dimensions:
1-11/32” o.d. x 1- 3/8” high with no mounting flange. Adapter is available with leads or
eyelets for soldering. Standard leads are 6” #18 AWM 1015 105°C.
Catalog Number
Rating
17-2
660W - 600V
17
1- 3/8
D.
1- 11/32
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
26 and 27 Series Quartz Halogen Lampholders
Front Flange Mounting
UL File No. E24691
26
This lampholder features a rugged two-piece porcelain body to withstand high ambient
temperatures. Corrosion-resistant housing and mounting bracket with reinforced
mounting plate are also included. Lampholder is assembled with a one-piece silverplated solid copper recessed contact, and a stainless steel spring to maintain contact
pressure. The telescoping lampholder is the same on both ends, giving a floating
condition to the lamp to absorb vibration. Standard leads are 18” #18 gauge SF-1,
SEW-1 200°C wire. Also available are 250°C wire leads.
•
•
•
Withstands high temperatures
Stainless steel spring maintains contact pressure
Absorbs vibration
Part Number
F01200260036-M
26 with 26” NAT #14 TXGT lead strip 1/2”
F01200270038-M
27 with 18” #18 200°C SF-2 lead strip 1/2”
Catalog
Number
Description
Temperature Rating
Wire Leads
Ratings
Lamps
26*
18” #18 TXGT leads
250°C
3000W - 600V
Tungsten-Halogen
27*
18” #18 SF-2 leads
200°C
3000W - 600V
Tungsten-Halogen
26
1- 7/64
15/16
31/32
11/64
1- 9/16
D.
53/64
21/32
1- 7/32
1/16
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
1- 11/16
MAX. PUSHED OUT POSITON OF PLUNGER
26A and 27A Series Quartz Halogen Lampholders
Rear Flange Mounting
UL File No. E24691
27A
This lampholder features a rugged two-piece porcelain body to withstand high ambient
temperatures. Corrosion-resistant housing and mounting bracket with reinforced
mounting plate are also included. Lampholder is assembled with a one-piece silverplated solid copper recessed contact, and a stainless steel spring to maintain contact
pressure. The telescoping lampholder is the same on both ends, giving a floating
condition to the lamp to absorb vibration. Standard leads are 18” #18 gauge SF-1,
SW-1 200°C wire. Also available are 250°C wire leads.
•
•
•
Stainless steel spring maintains contact pressure
Absorbs vibration
Part Number
F0120026A038-M
26A with 26” NAT #14 TXGT lead strip 1/2”
F0120027A017-M
27A with 18” #18 200°C SF-2 lead strip 1/2”
F01200270038-M
Catalog
Number
Description
Temperature Rating
Wire Leads
Ratings
Lamps
26A
250°C
3000W - 600V Tungsten-Halogen
27A
18” #18 SF-2 leads
200°C
3000W - 600V Tungsten-Halogen
26A
9/64
31/32
1
11/64
1- 9/16
D.
21/32
1- 7/32
D.
53/64
23/32
1/16
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
MAX. PUSHED OUT POSITON OF PLUNGER
34 and 35 Series Quartz Halogen Lampholders
Front Flange Mounting
UL File No. E24691
34
This one-piece porcelain body withstands high ambient temperatures. Its plunger
does not extend beyond the metal housing and features a corrosion-resistant housing
and mounting bracket. The lampholder is assembled with silver-plated, solid copper
recessed contacts. The body has access slots for easy lamp mounting. Standard leads
are 18” #18 gauge SF-1, SEW-1, 200°C wire. Also available are 250°C wire leads.
•
•
•
•
•
Easy mounting
Variety of mounting styles
Absorbs vibration
Very economical
Part Number
F01200340011-M
34 with 18” #14 TXGT lead strip 5/8”
F01200350011-M
35 with 9” #18 SF-2 black strip 1/2”
F01200350013-M
F01200350014-M
F01200350040-M
35 with 48” #18 SF-2 black strip 1/2”
F01201340037-M
134 with 18” #18 250°C TXGT leads strip 1/2”
Catalog
Number
Description
Temperature Rating
Wire Leads
Ratings
Lamps
34
250°C
3000W - 600V
Tungsten-Halogen
35
18” #18 SF-2 leads
200°C
3000W - 600V
Tungsten-Halogen
134
250°C
3000W - 600V 5kV pulse
Metal Halide (HQI)
135
18” #18 SF-2 leads
200°C
3000W - 600V 5kV pulse
Metal Halide (HQI)
34
31/32
15/16
1- 9/16
D.
53/64
1- 7/32
1/16
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
11/64
D.
21/32
226A and 227A Quartz Halogen Stationary Lampholders
Rear Flange Mounting
UL File No. E24691
226A
This lampholder features a rugged one-piece porcelain body to withstand high
ambient temperatures. A corrosion-resistant housing with reinforced mounting plate
is standard. The lampholder is assembled with a one-piece silver plated solid copper
recessed contact. A variety of conductors are available. See chart below.
•
•
For use in sets with quartzline telescoping lampholders
226A
15/16
Stationary and telescoping sockets may be used in sets to meet accessibility
requirements for relamping found in the UL Standard for incandescent lighting
fixtures. Place lamp in neutral-wired lampholder first when relamping
31/32
11/64
1- 9/16
Part Number
F0120226A001-M
226A with 18” black #16 TXGT strip 1/2”
F0120226A032-M
226A with 23” black #18 TXGT strip 1/2”
F0120227A040-M
227A with 18” #18 200°C black SF-2 strip 1/2”
D.
41/64
1- 7/32
D.
53/64
1- 9/64
Temperature Rating
Wire Leads
Ratings
Lamps
226A
250°C
3000W - 600V
Tungsten-Halogen
227A
18” #18 SF-2 leads
200°C
3000W - 600V
Tungsten-Halogen
*Quartzline lamps must be operated with 4 degrees of horizontal
326 Series Porcelain Recessed Lighting Lampholders
UL File No. E11033
Rated 660W - 250V
This white glazed porcelain lampholder is recessed approximately 3/16” on the
underside, with live eyelets recessed an additional 1/8”. It features a large wireway and
two mounting holes for easy assembly. The standard screw shell is aluminum with brass
or brass-nickel plated available by special order. Specify length and type of leads.
Leads attached. Rated 660W - 250V.
Mounting hole diameter 0.220.
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
425 Series Phenolic Twin-Light Lampholders
UL File No. E11033
425
These twin-light lampholders feature an all-molded construction which, eliminates
the need for metal brackets. They are ideally suite for ceiling fixtures, wall fixtures,
and aquariums. They can be molded using 175°C black phenolic (Catalog Number
425) or 100°C white urea (Catalog Number 425U). Various fittings and heights are
available to meet your exact needs. Lampholders with a snap spring are available
with a ground wire (Catalog #s 9425 or 9425U). The 425 Series can be ordered with
two conductor 18/2 SPT-1 with molded polarized plug or other end cut blunt, and with
in-line switches.
Twin-light lampholders with switches are Underwriters Laboratories recognized
components. Lampholders without switches, with standard 18 gauge leads are IL
listed. Lampholders with special usage 20 gauge leads are Underwriters Laboratories
recognized components.
Part Number
F02707L00003-M
425-7L with 19” #18 AWM 1015 leads strip 1/2”
F02707L00004-M
425-7L with 12” #18 AWM 1015 leads strip 1/2”
Catalog
Number
Top “C”
Dimension
Bottom “B”
Dimension
Top Fitting “A”
Dimension
Bottom Fitting “A” Rating
Dimension
425-7L
1- 21/32”
1- 5/32”
Snap Spring
None
660W - 250V
425-72M
2- 31/64
3/4
7/16
1- 17/64
1
1- 5/32
1- 17/64
1- 21/32
13/32
3/4
31/32
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
1/8-27 STD.
PIPE THD.
3/4
505A Series Keyless, Cap, Porcelain Lampholders
With Screw Terminals or Leads
UL File No. 11033
Rated 660W - 250V
•
•
•
•
Supplied standard with aluminum screw shell; brass or brass-nickel plated screw shell
also available to order.
Brass center contact is standard. Nickel brass plated center contacts are available. Optional
special leaf spring or coil spring loaded center contacts are available. Please specify.
Die-cast cap with fiber, 1/8” IP or 1/4” IP available. Please specify whether cap is to be
assembled or in bulk. When suited for wet locations, Nobestos fiber is available upon
request.
When ordering with leads, please specify lead length and type and strip length; also
specify whether leads are to be placed through cap or cut wireways (notches).
•
505A Series also available with screw (threaded 6-32 x 1/2”) or bushing mounting
(threaded 6-32).
•
•
•
Porcelain body can be supplied with one or two side notches, glazed or unglazed.
Reinforcing washers for placement inside screw shell are available upon request.
When ground wire is required, a “9” should be added as a prefix to the catalog number. All
ground leads are eyeletted to cap.
When ordering Catalog Number 505A specify with or without 1/8” IP die-cast cap. Order
Catalog Number 506A to specify with 1/4” IP cap.
•
505A
*Standard Stock: When ordering Catalog Number 505A with 1/8 IP cap refer to Part
Number F03800100C (unglazed, no side notches, two mounting screws captive,
aluminum screw shell, screw terminal, cap bulk packed).
Part Number
505A*
D.
19/32
1/8 Pipe Thread
7/16
2- 1/16
D.
1- 1/2
505A with
screw terminals
F03800060018-M 505A-6 unglazed with one side notch 84” #18 1015 Strip 1/2” fiber separate
F03800060039-M 505A-6 with terminals glazed with two side notches no cap fiber separate
F03800060044-M 505A-6 glazed with one side notch, 25” #18 SF-1 strip 1/2”
505A-6
F03800060046-M 505A-6 glazed one side notch, with leaf spring, reinforcements washers
and two bushings and 15” #18 SF-1 blunt
OPTIONAL
SIDE NOTCH
27/32
F03800060047-M 505A-6 glazed with one side notch with 6-32 bushings installed, reinforcement washer with 36” 18/3 SJTOW black cord, ROJ 6” on socket end, black
& white conductors on socket end to be covered with 3” #8 fiberglass sleeving. ROJ 2- 1/2”, strip all conductors 1/2” on customer end
6-32 BUSHING (2)
F038505A0073-M 505A glazed one side notch with cap 12” 1015 strip 1/2”
F038505A0132-M 505A unglazed 0SN 60” 1015 blunt leads through cap
505A-9
6-32 BUSHING (2)
27/32
F038505A0133-M 505A glazed, no side notches with 5/8” long screws inserted with 30” #18
SF-1 strip 1/2”
F038505A0137-M 505A glazed, no side notches, 9” black and white XFF 150°C leads, strip 1/2”
with fiber rubberized insulator gasket packed in bulk
1- 5/8
27/32
6-32 SCREWS (2)
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
1- 1/2
505A Series Keyless, Cap, Porcelain Lampholders
With Screw Terminals or Leads
505A Series Variations
Catalog
Number
Electrical
Leads
505A
505A-6
505A-9
Terminals
Mounting
Bushings
Finish
Screws
Side
Notches
Glazed Unglazed
Ratings
All 660W
X
X
X
X
None
250V
X
X
X
X
1
250V
X
X
X
X
None
250V
X
X
X
X
1
250V
X
X
X
X
None
250V
X
X
X
X
1
250V
X
X
X
None
250V
X
X
X
1
250V
X
X
X
2
250V
X
2
250V
X
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
X
557-37 Series Phenolic Fixture Lampholders with Insulating Cap
UL File No. E11033
Rated 600W - 250V
557-37-57 DN
The 557-37 Series phenolic cap completely covers and insulates the wire lead
terminal connection to comply with UL safety standards. Available on Catalog Number
557 phenolic lampholders, with any length and type of leads, to order. Cover has
regular mounting to fit our complete line of hickeys, brackets and springs. Phenolic
body is molded of heat-resistant phenolic. Standard screw shell is aluminum, with
brass or brass-nickel plated shell available to order. Ground wire available. Add “9”
to prefix.
Catalog Number 557-37-57 with side hickey lampholder with insulating cap and
side hickey mounted up or down. Variations in wiring option: Wire leads through side
notch in cap and through hickey. Both wires are put through the notch in the cap and
threaded through hickey.
Catalog Number 557-37 lampholder with insulating cap and spring attached, with
wire leads through individual wireways. Insulating cap accepts all springs used in
the 557 Series.
Part Number
557-37-57
5/16
1- 11/16
F05000370036-M 557-37-57 down 5/16R nipple with 6” #18 AWM 1015, leads routed
through notch in the cap, and leads through the hickey
F05000370055-M 557-37-305 up and 9” black #18 AWM 1015 strip 1/2” with 13”
white # 18 AWM 1015 strip 1/2”
F05008570010-M 557-38-857 down with 13- 3/4” (AWL) #18 black AWM 3173 125°C
topcoat strip 7/16” with 14” (AWL) #18 white AWM 3173 125°C
topcoat lead strip 7/16”
1- 1/4
D
557-37-A
5/16
1- 11/16
F05008570011-M 557-38-857 down with 25” (AWL) #18 black and white AWM 3173
125° strip 1/2”
1- 1/4
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
D.
557P Series Keyless, Cap, Porcelain Lampholders
Series 557P-147 through -150
UL File No. E11033
Rated 660W - 250V
557P-147
This unglazed porcelain body is available with screw terminals or with leads attached.
When ordering with leads, specify length and type of leads desired. Lampholder is
supplied with aluminum screw shell. Brass or brass-nickel plated shell is available to
order. Lampholder is available with screws or bushings for mounting. Also available with
caps. Caps furnished bulk packed when the lampholder is supplied with terminals.
Part Number
F05501470057-M 557P-147 with 18” #18 AWM 1015 leads strip 3/8”
F05601480029-M 557P-148 with side notch, bushings installed attached to 10T adapter with 10”
#18 SF-1 between with fiber 011-61010 on back of adapter
557P-147
F05601480043-M 557P-148 with side notch, 7- 1/8” #18 white SF-1 with 012-53808 lug and 7- 5/16”
# 18 black SF-1 with 012-53808 lug
7/16
D.
19/32
1/8 PIPE THREAD
1- 7/8
F05601480050-M 557P-148 with side notch 10- 1/2” #19 SF-1 with 012-53808 lug on each lead
F05601480061-M 557P-148 with one side notch with bushings with 30” black and white SF-1 leads
strip 1/2” with fiber insulator 011-61505A packed separate
F05201480003-M 557P-148 unglazed CNPS, NPCC with 6-32 bushings installed, reinforcement
washer with 36” 18/3 SJTOW black cord, ROJ 6” on socket end, cut back black
and white leads on socket end 3”, strip green conductor on socket end 1/4” and
leave free black and white conductors on socket end to be covered with 3” #8
fiberglass sleeving. ROJ 2- 1/2” strip all conductors 1/2” on customer end
D.
1- 3/8
557P-148
F05201480004-M 557P-148 unglazed CNPS, NPCC with 6-32 bushings installed, reinforcement
washer with 58” 18/3 SJTOW black cord, ROJ 6” on socket end, cut back black
and white leads on socket end 3”, strip green conductor on socket end 1/4” and
leave free black and white conductors on socket end to be covered with 3” #8
fiberglass sleeving. ROJ 2- 1/2” strip all conductors 1/2” on customer end
F05201480005-M 557P-148 with 7- 1/2” #18 AWM 1015 strip 1/2” and reinforced washers
F05201500011-M 557P-150 attached to a 10T adapter with an 001-11035 bracket eyeletted.
Fiber 011-61505A on the porcelain socket. The adapter and bracket assembly
screwed into the socket
557P-148
27/32
557P-147 through 150 Variations
Catalog Number
Electrical
Mounting
Side Notches
557P-147
leads
1/8” IP cap
none
1- 1/2
Listing
D.
1- 3/8
557P-148
leads
6-32 bushings
one
557P-150
leads
6-32 screws
none
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
561 Series High-Heat Bottom Turn Knob Socket
UL File No. E11033
Rated 660W - 250V
561
This one-piece phenolic bottom turn knob socket is molded of high-heat phenolic throughout.
Featuring a built-in rotary switch with non-removable knob or less knob with 4-36 threaded
stem. It is supplied with 3/8-27 shank by 11/32” long below hex nut, allowing for mounting not
over 1/8” thick. A 1/8 IP shank is available to order. Available with screw terminals or with wire
leads attached. Standard leads are 6” #18 AWM 1015 105°C. Other lengths or types of wire are
available to order. The socket is available in four bracket sizes. Overall lengths are measured
from top of socket to bottom of bracket. Removable knobs are available in metal or phenolic.
Finishing nuts are supplied separately.
•
•
•
561
One-piece construction
High-heat phenolic
Suitable for pin-up lamps and bullet lights
Part number
1- 1/4
2
F06620010022-M 561-1 aluminum screw shell with 3” #18 AWM 1015 strip 3/8”
with hex nut installed and aluminum finishing nuts separate
29/32
Switch Hardware
•
•
•
Hex nuts available in 1/8”-27 x 1/16” in zinc or black oxide finish. 1/8-27 x 3/32” in zinc
plated. 3/8-27 x 1/16” in brass plated and black oxide finish. 3/8-27 x 1/8” in brass plated.
Finishing nuts available in 1/8-27 double knurled in nickel, brass or black oxide finish.
3/8-27 single knurled in nickel, brass or black oxide finish.
Switch knobs available in long brass knurled, small brass knob, small zinc plated knob,
and small phenolic knob.
571V Series Snap-In Porcelain Lampholders for Recessed Lighting Fixtures
Rear Mounted
With leads attached
UL File No. E11033
Rated 660W - 250V
571V
This unglazed porcelain body supplied with any length and type of leads. This
lampholder is designed to reject the UL probe.
Sockets featuring recessed wire terminals (Style V Series) comply with the
accessibility probe requirement of UL Standard 1571. When ordering the 557 or 571
Series, add the suffix “V”.
Lampholders rated 660W - 600V are available. Consult factory.
571
D.
1- 3/8
Part Number
5/16
F0760000V001-M 571V with 36” black and white #18 XFF strip 1/2”
1- 1/4
F0760030V008-M 571V-30 with 14771-250 spring with 26” black and white
#18 SF-1 strip 1/2”
D.
1- 21/32
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
571V-30 Series In-Line Thermal Protection Wiring Harness Set
UL File NO. E123530
In-Line Thermal Protection Wiring Sets can be custom designed for your specific
applications. Thermal protection devices are available in temperature ratings from
70°C and up. Devices can be provided with insulating sleeves of various materials
and temperature ratings, or with our patented snap-in molded housing (suitable
for temperatures up to and including 130°C). Thermal protection device ratings are
available in 5° increments. When ordering, specify thermostat value in °C.
571V-30 with thermal
switch & insulation
sleeve closed
Specify wire type, lead lengths, and strip length. Also, specify length and type of wire
lead between thermal unit and lampholder.
The molded housing assembly is a recognized component under File Number E123530
(temperature indicating and regulating equipment).
Part Number
571V-30
F0760030V038-M 571V-30 with #14773-250 spring, BNPSS with 23- 1/4” #18 white SF-1 strip
5/8” with 10” #18 black SF-1 to #020-110A thermal switch with #98040 insulation sleeve closed with 17- 1/4” (AWL) #18 black XFF strip 5/8” off switch
F0760030V039-M 571V-30 with #14773-250 spring, BNPSS with 23- 1/4” #18 white SF-1 strip
3/8” twist and full tin with 10” #18 black SF-1 to #020-110A thermal switch
with #98040 insulation sleeve closed with 17- 1/4” (AWL) #18 black XFF strip
3/8” twist and full tin
F0760030V045-M 571V-30 with #14773-250 spring, BNPSS with 26” (AWL) #18 white SF-1
strip 5/8” with 12” #18 black SF-1 to #020-110A thermal switch with #98040
insulation sleeve closed with 22” (AWL) #18 black XFF strip 5/8” off switch
F0760030V046-M 571V-30 with #14773-250 spring BNPSS with 23” (AWG) #18 white XFF
strip 5/8” with 4- 1/2” #18 black XFF to #020-105A thermal switch with
#98040 insulation sleeve closed with 19” (AWG) #18 black XFF strip 5/8” off
switch
F0760030V063-M 571V-30 with# 007-14775 spring BNPSS with 24- 5/8” #18 white XFF strip
1/2” with 8- 3/4” #18 black XFF to #020-110A thermal switch without cover
with 20- 1/8” #18 black XFF strip 1/2” off switch
F07630021000-M 571V-30 with #007-14775 spring, with 30- 5/8” white #18 XFF strip 1/2” 153/4” black #18 XFF to #020-105A thermal switch without cover and 22- 1/8”
black #18 AWM 125° strip 1/2” off the switch
F07630022000-M 571V-30 with #007-14775 spring, with 30- 5/8” white #18 SF-1 strip 1/2”, 153/4” black #18 SF-1 to #020-105A thermal switch without cover and 22- 1/8”
black #18 AWM 125° strip 1/2” off the switch
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
WHITE
F0760030V034-M 571V-30 with #007-14775 spring with 24- 5/8” #18 white XFF strip 1/2” with
8- 3/4” #18 black XFF to #020-110A thermal switch without cover, with 201/8” #18 black XFF strip 1/2” off switch. Leave insulation on both strip
BLACK
F0760000V033-M 571V with 30” #18 white SF-1 lead strip 1/2” with 16” #18 black SF-1 lead to
#020-110A thermal switch with 26” #18 black SF-1 lead off switch strip 1/2”
BLA
CK
F0760000V031-M 571V BSSNP with 24- 5/8” # 18 white SF-1 lead strip 1/2” with 9- 1/8” #18
black SF-1 lead to #020-115A thermal switch with 24- 1/2” # 18 black SF-1
lead off switch strip 1/2”
571V-60 Series In-Line Thermal Protection Wiring Harness Set
UL File No. E123530
In-Line Thermal Protection Wiring Sets can be custom designed for your specific
applications. Thermal protection devices are available in temperature ratings from
70°C and up. Devices can be provided with insulating sleeves of various materials
and temperature ratings or with our patented snap-in molded housing (suitable for
temperatures up to and including 130°C). Thermal protection device ratings are
available in 5° increments. When ordering, specify thermostat value in °C.
571V-30 with
thermal switch
Specify wire type, lead lengths, and strip length. Also, specify length and type of wire
lead between thermal unit and lampholder.
The molded housing assembly is a recognized component under File Number
E123530 (temperature indicating and regulating equipment).
571V-60 with #14771-600 spring with 20- 5/8” white #18 SF-1
strip 7/16” and 8- 1/8” black SF-1 to #020-120A thermal switch
with 14- 3/4” black #18 AWM 1722 strip 7/16” off switch
F0760060V011-M
571V-60 with #14771-600 spring 20- 5/8” #18 white 200°C SF-1
lead strip 7/16” with 8- 1/8” (AWL) #18 200°C blue SF-1 lead to
#020-090A thermal switch with 14- 3/4” #18 XFF black lead strip
7/16” off switch
F0760060V012-M
571V-60 with #14771-600 spring, 20- 5/8” #18 white 200°C SF-1
lead strip 7/16” with 8- 1/8” #18 200°C red SF-1 lead to #020100A thermal switch with 14- 3/4” #18 AWM 125°C black lead
strip 7/16” off switch
F0760060V018-M
571V-60 with #14771-600 spring, 20” (AWG) #18 white 200°C
SF-1 lead strip 3/8” with 8- 1/4” (AWG) #18 200°C black SF-1
lead to #020-100B thermal switch with #06098040 sleeve on 17”
(AWG) #18 200 °C black strip 3/8” off switch
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
WHITE
F0760060V002-M
BLACK
BLA
CK
571V-60
Part Number
570-2 Series Snap-In Porcelain Lampholders for Recessed Lighting Fixtures
UL File No. E11033
Rated 660W - 250V
570-2
These one-piece porcelain lampholders are ideally suited for use in recessed lighting
fixtures. All feature a rust-proofed and tempered mounting spring attached to the
lampholder. The standard screw shell is aluminum, with brass or brass-nickel plated
shells available to order. Each of these lampholders can be supplied with any type and
length of leads.
Each of these lampholders can also be furnished with an insulated thermal switch
attached in-line, which is recognized by UL under the Wiring Harness program.
570-2
D.
1- 11/32
Part Number
F07200020005-M
570-2 with 30” #18 200°C SF-1 leads strip 1/2”
F07200020009-M
570-2 with 9” #18 AWM 1015 leads strip 1/2”
F07200020037-M
570-2 with 30” #18 200°C SF-1 leads strip 1/2”
F07200020052-M
570-2 with BNPSS with lamp grips with 36” #18 AWM
1015 strip 1/2”
27/32
27/32
1- 11/16
D.
616 Series Threaded Phenolic Lampholders
UL File No. E11033
Rated 660W - 250V
616
This medium-base phenolic lampholder features an outer threaded body with standard
aluminum shell.
Part Number
F09410000004-M
616 aluminum screw shell with 17” #18 AWM 1015
leads strip 5/8”
Catalog Number
Description
616
phenolic lampholder
616
D.
3/16
23/32
1/2 1- 9/16
1- 13/16
27/32
1- 9/16
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
1- 9/16
624 Series Quartz Halogen Lampholders
Rated 500W - 125V
624
This double-contact bayonet-base socket offers new operating convenience with single-ended quartz halogen lamps. This socket positions the lamp more accurately and
holds the lamp more securely, minimizing the possibility of the lamp shaking loose
from vibration. It is designed to provide optimum heat sink for cooler operation while
in the fixture.
Its construction complies with Underwriters’ Laboratories specifications for sockets
operating under heat conditions generated by quartz halogen lamps, and it is manufactured with high temperature leads. Sockets are supplied with 200°C or 250°C 6”
standard wire leads, with other lengths available to order. These sockets can be fitted
with all standard brackets and hickeys, as shown on the bayonet socket listings.
•
•
•
For general lighting, optical devices and instruments
Stage, film, and TV lights
Withstand high heat for quartz halogen lamp uses
Part Number
F0984A020106-M
624A-2 with 20” #18 200°C SF-1 black leads strip 1/2”
F0984A020108-M
624A-2 attached to 10A adapter BNPS, with SF-2 #18 black
between sockets, 624A-2 to be eyeletted to 10A adapter
F0984B050089-M
624B-5 with 8” #18 TXGT 250°C strip 3/16” with 1/8 x 27 hex
nut separate
Catalog Number
Description
*624A
with 6” 200°C wire leads
*624B
with 6” 250°C wire leads
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
624A
15/16
(2) 5/32 D. Holes
1- 5/16
1- 5/8
740 Series Medium & Ad Medium Base/HID Pulse Rated Porcelain Lampholders
UL File No. E11033
UL Recognized Component E11033.
threaded 6-32 on 27/32” centers.
Supplied with two captive bushings
740
This medium base 4kV pulse rated porcelain lampholder, with 660W - 600V 4kV
starting pulse., is for use with high pressure sodium lamps. The glazed porcelain
lampholder is supplied with a brass-nickel plated screw shell. Standard leads are 9”
#18 gauge SF-2 200°C -600 V wire. Other types or lengths of 600 V wire leads are
available to order.
A corrosion-resistant leaf spring under the center contact is available upon request.
Lamp grip screw shell is available upon request.
Part Number
F15000120003-M
740-12 brass-nickel plated screw shell, leaf spring and 12”
#18 200°C SF-2 strip 1/2”
F15000120004-M
740-12 brass-nickel plated shell, leaf spring and 36” #18
200°C SF-2 strip 1/2”
F15000120005-M
740-2 bushings installed brass-nickel plated screw shell
with 9” #18 200°C SF-2 leads strip 1/2”
F15000120006-M
740-12 brass-nickel plated screw with 36” #18 SF-2 strip
1/2”
F15000120013-M
740-12 brass-nickel plated screw shell with 18” #18 200°C
SF-2 leads strip 1/2” with 2 side notches
F15000120018-M
740-12 with 9” #18 200° SF-2 leads strip 1/2”
F15000120026-M
740-12 with 24” #18 200°C SF-2 strip 1/2” with 6-32 bushing installed and reinforcement washers
F15000120028-M
740-12 brass-nickel plated screw shell with lamp grip leaf
spring under contact, with reinforcement washers and 12”
#18 SF-2 leads strip 1/2” fiber insulator packed separate
F15000120032-M
spring under contact, with reinforcement washers and 28”
#18 SF-2 leads strip 1/2” fiber insulator packed separate
F15000120035-M
740-12 brass-nickel plated screw shell with 72” #18 SF-1
strip 1/2”
F15000120036-M
strip 1/2” with leaf spring under contact and reinforcement
washers
F15000120037-M
spring under contact with reinforcement washers and 18”
#18 SF-2 leads strip 1/2” fiber insulator paced separate
F15000120038-M
strip 3/8” with leaf spring under contact (no bushing)
Catalog Number Side Notches
740-12
2
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
740-12
D.
1- 17/32
START OF
THREADS
4KV
PULSE
RATED
TRIBORO
1- 21/32
3/16
6-32
BUSHINGS
27/32
770-2, 770-7 and 771 Series Snap-In High Heat Phenolic Lampholders
UL File No. E11033
Rated 660W - 250V
Tested by Underwriters Laboratories, Inc. at 200°C for 1,000 hours
770-2
Catalog Number 770-2 Front Mounted
High-heat phenolic body supplied with any length and type of leads. Spring clip
will accommodate material thicknesses from 0.032 to 0.093 inches.
Catalog Number 770-1 has a panel thickness range of 0.060 to 100 (1 or 2
panels).
Catalog Number 770-2 has a panel thickness range of 0.032 to 0.060.
Catalog Number 771 Rear Mounted
770-2
Part Number
F15400020002-M
770-2 brass screw shell with 9” #18 AWM 1015
strip 3/8”
F15400020028-M
770-2 10’ #18 white AWM 1015 strip 3/8” and 15”
#18 black 1015 strip 1/2”
F15400020037-M
770-2 with 15” #18 XFF strip 1/2” black and white
F15400020058-M
770-2 with spacer under spring aluminum screw
shell with 6- 1/2” 18/2 black SPT-1 105°C with bold
white stripe on ribbed conductor and with black
polarized plug
F15400020081-M
9770-2 with 15” #18 AWM 1015 strip 1/2” with 15”
#18 bare copper
F15400020084-M
770-2 with 5” #18 red AWM 1015 strip 3/8” with 4”
#18 white AWM 1015 strip 3/8”
F15500000020-M
771 with 14” #18 white AWM 125°C and with 9”
#18 black AWM 125°C with #012-53605 AMP lug
attached on both leads
D.
1- 11/16
High-heat phenolic body supplied with any length and type of leads.
Catalog Number 771 with leads attached. Designed specifically for recessed
down lighting.
23/64
19/64
1- 37/64
D.
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
1- 23/64
771
1- 5/8 D.
FLANGE
D.
1- 23/64
5/16
7/64
1- 9/16
1- 53/64
21/64
D.
1- 7/16
788 Series Snap-In Porcelain Lampholders
Surface Mounted
UL File No. E11033
This surface mounted lampholder features an unglazed porcelain body, with a flange
supplied with any length and type of lead.
Catalog Number 788 with leads attached UL File No. E11033 Rated 660W - 250V
Part Number
F171010T0002-M
1788 with 10” #18 SF-1 leads attached to 10T Adapter
with brass-nickel plated screw shells on both socket and
adapter with fiber on adapter
788
788
D.
1- 21/32
D.
1- 3/8
1- 5/8
9/16
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
800 Series High Heat Lampholders
UL File No. E11033
Tested by Underwriters Laboratories, Inc at 200°C for 1,000 hours
Rated 660W - 250V
802
These lampholders are fabricated from 200°C rated phenolic and come with a diecast metal cap with a set screw and fiber. Nobestos fiber is also available, but it must
be specified. Overall height is 1- 41/64” without the cap and 2- 3/32” with the cap.
Standard screws are 6-32 x 1/2” fillister head full thread when the lampholder is
supplied without a cap. When cap is supplied, either on or off, standard screws are
6-32 x 3/8” fillister head with full thread.
810-50
The lampholder comes with a standard center contact. A spring-loaded center contact
is available with a leaf spring only, and, if desired, it must be specified in the ordering
description. Reinforcing washers must also be specified if required.
1- 41/64
1- 9/16
When the lampholder is supplied with leads attached, all through instructions must
be specified.
1- 13/32
Part Number
mounting hole
for 6-32 captive
bushings or 6-32
captive screws
F15680200002-M 802 with 2 side notches with screw terminals less mounting
screws with fiber separate
F15680200004-M 802 with 2 side notches with screw terminals
Catalog
Number
Side
Notches
802
2
Wire Leads Terminals
X
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
Mounting
Screws
X
forms to accept
wire leads
Mounting
Bushings
1- 21/64
2 optional
side notch
1570-2 and 1770-2 Series Lampholders/Adapter (E26) Harness Combinations
UL File No. E26360
1770-2 17-2
This wiring harness designed for use in recessed downlighting features a high-heat
phenolic or porcelain snap-in lampholder attached to a phenolic adapter. Many
combinations of porcelain or phenolic sockets are available. Specify wire length and
type between the socket and adapter.
•
•
•
Many combinations available
Withstands high heat
Durable
Part Number
F16500170002-M
1570-2 attached to #17-1 adapter with 9” #18 XFF
leads between socket and adapter with brass-nickel
plated screw shell on both devices
F17400020002-M
1770-2 with #17-2 adapter with brass-nickel plated
screw shell on both devices with 9” #18 XFF between
socket and adapter
1770-2
Harness Combinations
Catalog Number
Load Fitting
Line Fitting
1570-2
570-2 lampholder attached to
10T or 17 phenolic adapter
1770-2
770-2 lampholder attached to
10T or 17 phenolic adapter
Cat. No. 17
Cat. No. 770-2
1570-2
CAT. No 17
CAT. No 570-2
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
H567-201 Series High Heat Phenolic Keyless Lampholders
For Outdoor Castings
UL File No. E11033
Rated 660W - 250V
Tested by Underwriters Laboratories, Inc. at 200°C for 1,000 hours
H567-201
These lampholders, molded of 200°C phenolic, are designed specifically for fast
assembly in outdoor castings. The standard screw shell is aluminum, with brass or
brass-nickel plated screw shell available to order. These lampholders are supplied
with leads attached, or with eyelets for soldering. Length and type of leads must be
specified when ordering. Reinforcing washers are available on request.
These lampholders feature several different installation options that allow the user to
choose configurations for any assembly requirements.
H567-201
1- 15/32
H567 Series is sold without brackets. If bracket is required, see 557 Series. Ground
wire available, add “9” to prefix.
Catalog Number H567-201
With captive 8-32 PAL nut.
Note wiring positions: Positions 3 or 4 must be black, positions 5 or 6 may be white or
optionally positions 1 or 2. Standard wiring position is black 3 and white 5.
Part Number
F07002010015-M
H567-201 brass-nickel plated screw shell and center contact
with 36” #18 AWM 1015 strip 5/8” lugged leads using 3-5 pattern
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
D.
1- 11/32
403 Series Snap-In Convenience Outlet and Male Load Plug
UL File No. E18457
Rated 15A - 125V
403-1
These snap-in outlets, molded of black phenolic or white urea, are designed specifically
for surface mounting in fixtures and appliances. They also are adapted for use with
flat type plug caps. The outlet is supplied with tempered-steel spring clips to hold-in
place. This spring will accommodate a wall thickness of 0.031” to 0.062”. Standard
leads are 6” #14 AM 1015 105°C leads, with other lengths available to order.
•
•
•
For appliances, lighting fixtures, home entertainment systems and general
applications
Designed to allow surface and panel mounting
Snap-in design allows easy mounting and tight fit
Part Number
403-1
29/32
F02800010009-M 403-1 6” #14 1015 black and white
3/16
F02800110004-M 403-11
F02800210014-M 403-21 with 6” #18 1015 black and white
29/32
F02800210022-M 403-21 with 18” #18 1015 black and white
1- 5/32
F02800250003-M 403-25 with 6- 1/4” #18 1015 black and white
403-11
403-1
Snap-in outlet, black with #14 or #16 gauge leads
403A-1
Snap-in outlet, white with #14 or #16 gauge leads
403-11
Snap-in outlet, with quick tab terminals -black
403A-11
Snap-in outlet, with quick tab terminals -white
*403-21
Snap-in outlet, black with #18 gauge leads
*403A-21
Snap-in outlet, white with #18 gauge leads
*403-25
Snap-in outlet, black with #18 gauge wire exits back of outlet
*403A-25
Snap-in outlet, white with #18 gauge wire exits back of outlet
403-11
* UL recognized components (not CSA)
1- 5/32
3/16
29/32
1- 5/32
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
655 Series Snap-in Outlets 3-Wire and 4-Wire U-Ground
Narrow Rectangular Face
UL File No. E18457
Rated 15A - 125V
655
These snap-in outlets, molded of black phenolic or white urea resin, are designed
specifically for use in narrow locations and shallow canopies. These outlets meet the
latest 3-wire National Electrical Code grounding requirements.
Tempered-steel spring clips with corrosion-resistant finish are supplied to accommodate
any material from 0.031 to 0.062” thick. Standard leads are 2 #14 gauge 105°C 6”
black and white AWM leads and one #16 gauge 105°C 6” green AWM lead. Any length
and type of wire is available to order. These outlets are also available with 4 wire
ground lead styles with terminal lugs attached for permanently fastening the ground
lead to the fixture.
655A
When ordered with #18 gauge AWM UL 1015, product is a Recognized Component.
Use -31 as suffix when ordering.
•
•
•
Snap-in for easy installation
For use in narrow and shallow installations
Clips fit a wide range of material thicknesses
Part Number
F1180000A007-M
655A 6” #14 1015 and 6” green #16 strip 1/2”
F1180000A008-M
655A 6” #14 1015 black and white with #8 ring lug on green wire
F11800000003-M
655 6” #14 1015 black and white, 6” green #16 strip 1/2”
F1180031A001-M
655A-31 2- 1/2” black, white and green with #808 lugs (3) leads
Catalog Number
Color
Description
655
black
3-wire grounded outlet
655A
white
3-wire grounded outlet
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
1- 7/32
15/16
27/32
5/32
675 Series U-Ground Snap-In Male Load Plugs
UL File No. E26302
NEMA 5-15P
675-81
These load plugs, molded of black phenolic or white urea, feature tempered-steel
spring clips with a corrosion-resistant finish. Plugs are also supplied with brass blades
and grounding-pin.
Terminations: Load plugs are available in the following combinations: Two 250°C quick
connect tab terminals, one green grounding lead #16 AWM 1015 105°C, two 250°C
quick connect tab terminals and ground terminal screw; two #14 AWM 1015 105°C
leads and one green grounding lead #16 AWM 1015 105°C. When ordered with #18
AWM UL 1015, product is a Recognized Component. Use -31 suffix when ordering.
•
•
•
Matches 675-11 for lighting fixtures and major appliances
Meets three-wire code requirements
Snaps in for easy installation and secure fit
Part Number
F13200510003-M
675-51 6” #16 green 1015 with #10 ring lug
F1320081A001-M
675A-81 6” #14/#16 1015 green strip 1/2”
F1320081A016-M
675A-81 #16 1015 black, white and green
F13200810025-M
675-81 6” #14/#18 1015 with #10 ring lug on green wire
Catalog Number
Color
Description
675-51
black
male terminals and #16 green ground leads
675A-51
white
male terminals and #16 green ground leads
675-81
black
#14 plastic leads and #16 green ground lead
675A-81
white
#14 plastic leads and #16 green ground lead
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
675
5/16
1- 1/16
1- 1/16
1- 3/16
3/16
25/32
19/32
675 Series U-Ground Snap-In Outlets
UL File No. E18457
NEMA 5-15R
Rated 15A - 125 V
675-1
These snap-in outlets feature tempered-steel clips with corrosion-resistant finish to
accommodate any material from 0.031 to 0.062” thick. The molded plastic body is
available in black phenolic or white urea.
Terminations: Outlets are available in the following combinations: two .250” quick
connect tab terminals, one green grounding lead #16 AWM 1015 105°C; two .250”
quick connect tab terminals and ground screw; or two #14 AWM 1015 105°C leads
and ground screw. For panel thicknesses other than stated, consult factory. When
ordered with #18 AWM UL 1015, product is a Recognized Component. Use -341 as
suffix when ordering.
•
•
•
675A
5/16
1- 1/16
For lighting fixtures and major appliances
Meets three-wire code requirements
Snaps-in for easy installation and secure fit
Part Number
F13200010021-M
675-1 with 6” green #16 1015 strip 1/2”
F13200010022-M
675-1 6- 1/2” green #16 1015 with #10 ring lug
F13200010024-M
675-1 6” green #16 1015 with #10 ring lug
F13200010025-M
675-1 6” green #16 1015 with 263 ring lug
1- 1/16
1- 3/16
3/16
19/32
Catalog Number
Color Description
675-1
black
Male terminals and #16 green ground leads
675A-1
white
Male terminals and #16 green ground leads
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
ZE-204 Series Rocker Switches
Single Pole, Single Throw
UL File No. E89885
Rocker switches are available in black and white. Standard versions with leads are
6” #18 gauge AWM 1015 105°C tinned inners, stripped 1/2”. Other lead lengths are
available upon request, subject to minimum order. On/Off markings are not standard
stock, however they are available upon request. Consult factory.
Part Number
SRK-F11WL6FT
6” length of (2) black #18 UL 1015, 105°C stranded tinned
copper strip 0.375” minimum to 0.437” maximum full tinned
solder dipped
SRK-M11WL6FT
ZE-204
ZE-204
1.235
miniature rocker switch with (2) black 6” leads, color white
#18 AWM UL 1015 105°C stranded tinned inners, cut the
5/8” strip length down to 3/8”, twist and full tin on 3/8” strip
on both ends
0.200
0.860
1.120
0.675
0.390
0.050
0.810
0.544
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
Uninsulated Copper Wire
UL 79D2 Fixture Fitting
Catalog Number AWG Size
Stranding
Weight LB/M
Standard Package
508A
7/.0152 Bare 3/8 Lay
5
250’
18
508S
18
7/.0152 Bare 3/8 Lay
5
1000’
508R
18
7/.0152 Bare 3/8 Lay
5
2500’
518A
18
7/.0152 Bare 3/8 Lay
5
250’
518S
18
7/.0152 Bare 3/8 Lay
5
1000’
518R
18
7/.0152 Bare 3/8 Lay
5
2500’
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
AWM Style 1015 Single Conductor
AWM Style #1015
Rated 105°C - 600V
CSA Type TEW
Underwriters’ Laboratories Recognized
CSA Certified
solid
Appliance Wiring Material
Conductor: Solid or stranded bare or stranded tinned copper Insulation: PVC
Catalog
Number
AWG
Size
Inches Stranding Approximate Weight
Thick
O.D.
LB/M
Standard Standard
Package Carton
208S
18
0.031
16/30
0.107
10
500’
2000’
208R
18
0.031
16/30
0.107
10
5000’
-
228S
18
0.031
SOLID
0.105
10
500’
2000’
228R
18
0.031
SOLID
0.105
10
5000’
-
206S
16
0.031
26/30
0.123
14
500’
2000’
206R
16
0.031
26/30
0.123
14
4000’
-
226S
16
0.031
SOLID
0.128
14
500’
2000’
226R
16
0.031
SOLID
0.128
14
4000’
-
204S
14
0.031
41/30
0.139
20
500’
1000’
204R
14
0.031
41/30
0.139
20
4000’
-
224S
14
0.031
SOLID
0.128
20
500’
1000’
224R
14
0.031
SOLID
0.128
20
4000’
-
Part Number
F21600200024-M
18” white #18 AWM 1015 solid strip 3/8” both ends
F21600300079-M
12” red #18 AWM 1015 solid strip 3/8” both ends
F21600300107-M
8” red #18 AWM 1015 solid strip 3/8” both ends
F21600400012-M
12’ blue #18 AWM 1015 solid plastic strip 3/8” on both ends
F21600400068-M
8” blue #18 AWM 1015 solid strip 3/8” both ends
F21600500007-M
6” green #18 AWM 1015 strip 3/4” with #6 lug
F21600500127-M
6” green #18 AWM 1015 strip 3/8” with #6 lug, twist and full dip tin
F21600500130-M
9” #18 1015 VW BC green strip 1/4” 1 end other end #6 lug
F21600500131-M
12” #18 SBC green 1015, with #8 ring lug X strip 1/2”
F21600500132-M
9” green #18 AWM 1015 with 01253271 lug on both ends
F21600500134-M
8- 1/2” white #18 AWM 1015 with #10 terminal on both ends
F21600700004-M
18” yellow #18 AWM 1015 solid strip 3/8” both ends
F21600100120-M
18” black #18 TFN SBC strip 3/8” both ends
F21600700097-M
F21600700109-M
12” yellow #18 AWM 1015 SBC, strip 3/8” both ends
F21600700112-M
F23820029000-D
blue #18 solid bare copper 105°C on 5000 foot reel
F23820034000-D
red #18 solid 1015 DEG with bare copper inners on 5000 foot reel
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
stranded
lugs
AWM Style XFF Single Conductor
AWM Style #XFF
Rated 150°C - 600V
CSA Type CL - 3321
Underwriters’ Laboratories Recognized
CSA Certified
#18 XFF
AWM Thermoplastic Elastomer
Catalog
Number
AWG
Size
Inches
Thick
Stranding
Approximate
O. D.
590S
18
0.031
16/30
0.110
590R
18
0.031
16/30
0.110
Part Number
F21600100021-M
28” black #18 XFF 150°C, strip 3/16” x 3/8”
F21600100022-M
15” black #18 XFF 150°C, strip 3/16” x 3/8”
F21600100060-M
12” black #18 XFF 150°C, strip 3/8” both ends
F21600200022-M
23- 5/8” white #18 XFF 150°C, strip 3/16” x 3/16”
F21600200040-M
12” white #18 XFF 150°C, strip 3/8” both ends
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
Style SF-1 and SF-2 Single Conductor
Type UL SF-1,
CSA SEW-1 200°C 300V
UL SF-2
CSA SEW-2 200°C 600V
style #18 SF-1
Silicone Rubber Insulated Fixture with Fiberglass Braid
Conductor: Stranded tinned copper Insulation: Silicone rubber Braid: Fiberglass
Catalog Number AWG
Size
Inches
Thick
Stranding
Approximate
O. D.
Weight
LB/M
Standard
Package
488S
18
0.016
7 x 0.0152
0.098
9
500’
488R
18
0.016
7 x 0.0152
0.098
9
5,000’
498S
18
0.031
7 x 0.0152
0.128
12
500’
498R
18
0.031
7 x 0.0152
0.128
12
5,000’
496S
16
0.031
7 x 0.0192
0.137
18.5
500’
496R
16
0.031
7 x 0.0192
0.137
18.5
4,000’
SF-1
SF-2
SF-2
SF-2
494S
14
0.031
7 x 0.0242
0.153
25
500’
494R
14
0.031
7 x 0.0242
0.153
25
3,500’
Part Number
F21600200042-M
14” white #18 SF-1 strip 1/2” and full dip, tin, cut 2nd. end blunt
F23820007000-D
18 SF-1 white 7,500/RL
F23820008000-D
green #18 SF-1/SEW-1 200°C on 5,000 foot reel
F23820024000-D
black #18 SF-2/SEW-2 200°C on 5,000 foot reel
F23820025000-D
white #18 SF-2/SEW-2 200°C on 5,000 foot reel
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
style #16 SF-2
Harness Assembly
Labelled AWM Style 1015 14 AWG
Rated 105°C 600V
Recognized Component Connector Molex Series 1396
Rated 350 volts
Part Number
F21602040000-M
12- 1/2” harness 3-wire black, white and red
F21602040001-M
12- 1/2” harness 2-wire black and white
F21602040002-M
12- 1/2” harness 2-wire orange and gray
2-wire black & white
Tel: (877) 257-5841 • Fax: (800) 438-2500
www.alplighting.com
2-wire range & gray
3-wire black, white & red

620 Series Medium Bi-Pin Fluorescent Quickwire

Transcription

Similar documents