DISTRIBUTED BY: www.iMETAL.net PHONE: 267-983-1017

Transcription

secondary framing
Profiles
STANDARD CEES AND ZEES
Members can be manufactured to the nearest 1/8" in length from 6'-0" to 45'-0" (for Cees) and 7'-0" to 45'-0" (for Zees).
For lengths other than listed, please inquire.
B1
CEE
ACTUAL SIZE GAUGE
Web x B1 x B2 12 14 16
FINISH
 
 

 




10" x 21/2" x 21/2" 
10" x 3" x 3" 
10" x 31/2" x 31/2"  10" x 4" x 4" 
12" x 21/2" x 21/2"  12" x 3" x 3" 
12" x 31/2" x 31/2"  Red Oxide
Red Oxide
Galvanized
Red Oxide
Galvanized
Red Oxide
Red Oxide
Red Oxide
Red Oxide
Red Oxide
Red Oxide
Red Oxide
Red Oxide
Red Oxide
Red Oxide
4" x 21/2" x 21/2"
6" x 21/2" x 21/2"
6" x 21/2" x 21/2"
8" x 21/2" x 21/2"
8" x 21/2" x 21/2"
8" x 31/2" x 31/2"
9" x 3" x 3"
9" x 31/2" x 31/2"
WEB
B2
B1
ZEE
WEB
B2
(Symmetrical Flange)
MANUFACTURED
LOCATION
Sellersburg / Longmont / Jacksonville / Woodland
Sellersburg / Jacksonville / Woodland
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
LGSI ZEES
Members can be manufactured to the nearest 1/8" in length from 7'-0" to 45'-0".
For lengths under 7'-0" or over 45'-0", please inquire.
ACTUAL SIZE GAUGE
Web x B1 x B2 12 14 16
 
 
B1

 


5
7
9" x 2 /8" x 2 /8" 
LGSI ZEE
WEB
9" x 31/8" x 33/8" 
10" x 21/8" x 23/8"  
10" x 25/8" x 27/8" 
10" x 31/8" x 33/8"  10" x 35/8" x 37/8" 
B2
12" x 21/8" x 23/8" 
(Unsymmetrical Flange) 12" x 25/8" x 27/8" 
12" x 31/8" x 33/8" 
4" x 21/8" x 23/8"
6" x 21/8" x 23/8"
6" x 21/8" x 23/8"
8" x 21/8" x 23/8"
8" x 21/8" x 23/8"
8" x 31/8" x 33/8"
PSF-4
FINISH
Red Oxide
Red Oxide
Galvanized
Red Oxide
Galvanized
Red Oxide
Red Oxide
Red Oxide
Red Oxide
Red Oxide
Red Oxide
Red Oxide
Red Oxide
Red Oxide
Red Oxide
MANUFACTURED
LOCATION
© Metal Sales Manufacturing Corporation/ Subject to change without notice/ Effective Date 9/11
800.406.7387
(Corporate
Office) • www.metalsales.us.com
iMetal.net
- Phone:
267-983-1017 - www.iMetal.net
secondary framing
PATTERN #1
Cee and Zee Punch Patterns
FOR STANDARD ZEES ONLY
7"
CL
11/2"
1
/2" Bay Width
2"
5
4"
5
/8" x 3/4" Vertical Slots
/8" Round Holes
11/2"
11/2"
Punch pattern
is similar on
both ends.
/ " Round Holes Shown (Sellersburg, IN) or (Jacksonville, FL)
/ " x 3/4" Horizontal Slots (Longmont, CO only)
5 8
5 8
11/4"
Flange
Bottom of Purlin
31/2"
11/2"
PATTERN #2
/ " x 3/4" Vertical Slots Shown (Sellersburg, IN) or (Jacksonville, FL)
Standard punch patterns not available on 4" web members.
5 8
5 8
1
1 /2"
1
1'-2"
11/4"
Flange
CL
/2" Bay Width
1'-1/2"
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
5
4"
2'-4"
5
/8" Round Holes
11/2"
11/2"
Punch pattern
is similar on
both ends.
Bottom of Purlin
11/2"
1'-1/2"
1'-2"
PATTERN #3
11/2"
5 8
5 8
/ " Round Holes Shown (Sellersburg, IN only)
5 8
1
11/2"
3'-6"
CL
/2" Bay Width
1'-71/2"
1'-9"
5
4"
5
11/4"
Flange
/8" Round Holes
11/2"
11/2"
Punch pattern
is similar on
both ends.
Bottom of Purlin
1'-71/2"
1'-9"
5 8
11/2"
5 8
5 8
5 8
800.406.7387
(Corporate Office)
• www.metalsales.us.com
iMetal.net - Phone:
267-983-1017
- www.iMetal.net
PSF-9
secondary framing
PATTERN #A
13/4"
For 2'-31/2" or 4'-31/2" Laps
For Standard and LGSI Zees
1'
1'
2"
2"
1'
CL
1'
5
2"
2"
11/2"
11/2"
Punch pattern
is similar on
both ends.
If LGSI, Wide Flange Indicator
4"
2"
4"
4"
5
/8" Round Holes
2'-4"
No flange punching for pattern #A.
PATTERN #B
13/4"
For Standard and LGSI Zees
1'
1'
1'
For 2'-31/2", 4'-31/2", or 6'-31/2" Laps
1'
CL
1'
1'
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
2"
2"
2"
4"
2"
11/2"
11/2"
Punch pattern
is similar on
both ends.
4"
4"
2"
2'-4"
33/4"
5
4"
/8" Round Holes
5
No flange punching for pattern #B.
PATTERN #C
4"
For Standard and LGSI Cees and Zees only
No Lap
1
1
/4"
13/4"
CL
/2" Bay Width
1"
5
/8" Round Holes
11/2"
4"
/ " Round Holes Shown (Sellersburg, IN only) or 5/8" x 3/4" Horizontal Slots (Longmont, CO only)
5 8
11/4"
Flange
/2" Gap
No Lap
1
11/2"
Punch pattern
is similar on
both ends.
Bottom of Purlin
11/4"
3"
/ " x 3/4" Vertical Slots Shown (Sellersburg, IN only)
5 8
5 8
PSF-10
800.406.7387
(Corporate
iMetal.net
- Phone:
secondary framing
PATTERN #D
For 2'-31/2" or 4'-31/2" Laps
For LGSI Zees only.
1'
13/4"
1'
2"
4"
1'
1'
2" 4"
2"
2"
CL
4"
4"
5
11/2"
/8" Round Holes
11/2"
Punch pattern
is similar on
both ends.
4"
5
13/4"
Flange
Bottom of Purlin
21/4"
11/2"
11/2" 11/2"
11/2"
1'-13/4"
11/2"
11/2"
1'
11/2"
11/2"
/ " x / " Vertical Slots Shown (Sellersburg, IN) or (Jacksonville, FL)
5 8
3 4
5 8
11/2"
1'
5 8
5 8
For LGSI Zees only.
PATTERN #E
1'
1'
13/4"
2"2"
4"
1'
2"
2"
For 2'-31/2", 4'-31/2", or 6'-31/2" Laps
2" 4"
1'
1'
2" 2"
2"
CL
1'
4"
4"
4"
11/2"
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
Punch pattern
is similar on
both ends.
4"
11/2"
5
Bottom of Purlin
/8" Round Holes
5
21/4"
11/2" 11/2"
11/2"
1
2
1
/
"
11/2"
1'
1'-13/4"
13/4" from web (Sellersburg, IN) or (Jacksonville, FL)
11/4" from web (Longmont, CO only)
PATTERN #F
11/2" 11/2"
11/2"
1'
5 8
For LGSI or Standard Zees only.
1'
1'
2"
4"
5 8
5 8
1
13/4"
5 8
2'-31/2"
CL
/2" Bay Width
1'-4"
2"
11/2"
5
5
11/2"
/8" Round Holes
Punch pattern
is similar on
both ends.
Bottom of Purlin
11/2"
1'-1 /4"
3
5 8
11/2"
5 8
5 8
5 8
800.406.7387
(Corporate Office)
iMetal.net - Phone:
267-983-1017
- www.iMetal.net
PSF-11
secondary framing
PATTERN #G
For Standard Zees only.
4'-31/2"
1
13/4"
2'
2'
2"
4"
CL
/2" Bay Width
2"
4"
11/2"
5
5
11/2"
Punch pattern
is similar on
both ends.
/8" Round Holes
Bottom of Purlin
/ " x 3/4" Vertical Slots Shown (Sellersburg,IN) or (Jacksonville, FL)
5 8
5 8
11/2"
11/2"
5 8
2'-13/4"
5 8
PATTERN #H
For Standard Zees only.
6'-31/2"
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
1
13/4"
8"
2'-4"
2'-4"
CL
8"
2"
2"
4"
/2" Bay Width
11/2"
5
5
11/2"
/8" Round Holes
Punch pattern
is similar on
both ends.
Bottom of Purlin
5 8
5 8
11/2"
11/2"
3'-13/4"
5 8
PATTERN #J
5 8
For LGSI or Standard Zees and Cees only.
13/4"
4"
5
Punch pattern
is similar on
both ends.
/8" Round Holes
PSF-12
800.406.7387
(Corporate
iMetal.net
- Phone:
secondary framing
Custom Punching
Sellersburg, Indiana line only
Custom punching can be done for Standard
Cees, Zees, LGSI Zees, and Eave Struts.
Web punching is available in 4" to 12" Cees,
Zees, and Eave Struts. Punching is available
only on center line of web for 4" member.
Any combination of punching (1-11)
can be punched together.
Flange punching is available in 6" to 12" Cees,
Zees, and Eave Struts only.
Both holes or slots in 3, 4, 5, 6, 7, 10, and 11
must be punched together.
1
2
3
4
5
6
7
8
9
10
10
11
11
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
1"
1"
C
L 1"
1"
3"
3"
5
"X"
"Z"
5
3" spacing required between
holes or slots in flanges.
/8" Round Holes
FLANGE PUNCHING
Flange punching can be punched in either "X" or "Z".
"X" must be 11/4", 13/4", or 2" from web.
"Z" must be 21/4", 3", or 4" from web.
Flange width must be 27/8", 3", 33/8",
31/2", 37/8", 4", or 5" for punching
second holes or slots ("Z").
Zee
LGSI Short
Flange
Web
Cee or
Eave Strut
"X"
"X"
"Z"
Flange
PSF-14
C
L
800.406.7387
(Corporate
iMetal.net
- Phone:
Flange
secondary framing
Custom Punching
Longmont, Colorado line only
Cees, Zees, and Eave Struts.
Zees, and Eave Struts.
Any combination of punching (1-12)
can be punched together.
1
2
3
4
5
6
7
8
12
11
9
1"
1"
C
L 1"
1"
11/4"
10
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
5
5
5
21/4"
5
/8" x 3/4" Horizontal Slots
/8" Round Holes
FLANGE PUNCHING
Flange punching can be punched in either "X", "Z", or Both dimensions from web.
Zee
Flange width must be 3" or 31/2" for
punching second slots.
Web
Cee or
Eave Strut
11/4"
C
L
21/4"
11/4"
Flange
Flange
800.406.7387
(Corporate Office)
iMetal.net - Phone:
267-983-1017
- www.iMetal.net
PSF-15
secondary framing
Custom Punching
Jacksonville, Florida line only
Cees, Zees, LGSI Zees, and Eave Struts.
Any combination of punching with the exception
of (8) can be punched together.
Zees, and Eave Struts. Punching is available
only on center line of web for 4" member.
Both holes or slots in 3, 4, 5, 6, 7, 8, 14, and 15
must be punched together.
All four holes or slots in 9, 10, and 11 must be
punched together.
1
2
3
4
5
6
8 8
7 3"
9
9
4"
10
10
4"
11
11
4"
15
14
13
12
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
3"
3"
1"
1"
C
L 1"
1"
5
"X"
"Z"
5
3" spacing
required between
holes or slots in
flanges.
/8" Round Holes
FLANGE PUNCHING
Flange punching can be punched in either "X" or "Z".
"X" must be 11/4", 13/4", or 2" from web.
"Z" must be 21/4", 3", or 4" from web.
Zee
LGSI Short
Flange
Flange width must be 27/8", 3", 33/8",
31/2", 37/8", 4", or 5" for punching
second holes or slots ("Z").
Web
Cee or
Eave Strut
"X"
"X"
"Z"
Flange
PSF-16
C
L
800.406.7387
(Corporate
iMetal.net
- Phone:
Flange
secondary framing
Custom Punching
Woodland, California line only
*Punching Capabilities
Cees, Zees, and LGSI Zees.
Description
/8" Hole
/8" x 3/4" Vertical Slot
5
/8" x 3/4" Horizontal Slot
13
/16" Hole
13
5
Web punching is available in 4" to 14" Cees
and Zees.
5
11
Flange punching is available in 4" to 14" Cees
and Zees only.
/16" Hole
1 /16" Hole
13
1
7
/16" Hole
1
2
3
4
5
9
6
"Z"
"X"
C
L
A**
D**
7 8
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
B**
C**
*See Punching Capabilities
*See Punching Capabilities
"Q"
"R"
*See Punching Capabilities (above left).
**Dimensions A, B, C, and D must be within web of purlin, please contact
the Woodland Branch for more information (see page PGI-2-3).
FLANGE PUNCHING
Top Flange
Flange punching can be punched in either "X", "Z", "Q", or "R".
"X" must be 3/4" from web and no more than 3/4" from flange.
"Z" must be 3/4" from web and no more than 3/4" from flange.
"Q" must be 3/4" from web and no more than 3/4" from flange.
"R" must be 3/4" from web and no more than 3/4" from flange.
Top Flange
Bottom Flange
Flange
"Z"
"X"
"Q"
"R"
"X"
LGSI Short
Flange
C
L
Zee
Web
Cee or
Eave Strut
Flange
Flange width must be 27/8", 3", 33/8", 31/2", 37/8", or 4" for
punching second holes or slots ("Z")"Top Flange" or
("R")"Bottom Flange".
800.406.7387
(Corporate Office)
iMetal.net - Phone:
267-983-1017
- www.iMetal.net
C
L
"Q"
Bottom
Flange
PSF-17
secondary framing
Standard Cee and Zee Information
GENERAL INFORMATION
Standard Secondary Framing (members with symmetrical flanges) are available in 4", 6", 8", 9", 10", and 12" web sizes and
available in 2-1/2", 3", 3-1/2", 4", and 5" flange sizes. Metal Sales offers members in various gauges and finishes. In addition,
members can be ordered to your desired length with standard or custom punching. For your specific loading requirements please
reference Metal Sales' Technical Reference Product Manual.
Symmetrical Flanges at Lapping
Lapped Zees
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
Cees
PSF-18
800.406.7387
(Corporate
iMetal.net
- Phone:
secondary framing
SHORT LAP
Standard Zee Lap Information
TWO SPAN
7"
7"
lapped
section
Zee
Lapped
Section
3 OR MORE SPANS
7"
7"
7"
lapped
section
lapped
section
lapped
section
LONG LAP
2' - 4"
TWO SPAN
Zee
2' - 4"
lapped
section
Lapped
Section
3 OR MORE SPANS
2' - 4"
lapped
section
MAX LAP
2' - 4"
2' - 4"
lapped
section
lapped
section
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
3' - 6"
Zee
TWO SPAN
Lapped
Section
3' - 6"
lapped
section
3 OR MORE SPANS
3' - 6"
lapped
section
SIMPLE SPAN (NO LAP)
3' - 6"
lapped
section
3' - 6"
lapped
section
800.406.7387
(Corporate Office)
iMetal.net - Phone:
267-983-1017
- www.iMetal.net
PSF-19
secondary framing
STANDARD SHORT LAP
Standard Zee Lap Information (cont.)
7" Lap
11/2"
11/2"
4"
11/2"
3"
For required lap condition use standard
punch pattern #1.
STANDARD LONG LAP
2'-4" Lap
11/2"
11/2"
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
11"
punch pattern #2.
STANDARD MAX LAP
11/2"
3"
1'-2"
11"
3'-6" Lap
11/2"
11/2"
11/2"
1'-6"
punch pattern #3.
STANDARD (NO LAP)
3"
1'-9"
1'-6"
4"
1
1"
/2" Gap
11/2"
punch pattern #C.
PSF-20
3"
800.406.7387
(Corporate
iMetal.net
- Phone:
secondary framing
Dimensions and Section Properties of Standard Zees
B1
Fy = 55.0 KSI
R = 0.125 In
WEB
B2
Effective Section Properties
(Fully Braced) X-X Axis
Full Section Properties
SIZE
Thickness Weight
in
plf
Web x Flange GA
A
In2
Ix-x
in4
rx
in
Iy-y
in4
ry
in
Cw
in6
J
In4
Ae
in2
Ixe
in4
Sxe
in3
Max
K-ft
Vay
Kips
16 0.057 1.926 0.5661.5521.6651.0791.3802.5430.000610.3811.3580.6211.704 3.665
4" x 21/2"
14 0.070 2.365 0.6961.8911.6491.3341.3853.1350.001140.5151.7040.7932.176 5.367
16 0.057 2.314 0.6803.9102.3971.0791.2596.2980.000740.3893.4521.0662.927 2.865
6" x 21/2"
14 0.070 2.841 0.8364.7782.3911.3341.2637.7670.001370.5304.3271.3553.719 5.331
16 0.057 2.701 0.7947.6283.0991.0791.16512.0000.000860.3936.6111.5124.150 2.102
8" x 21/2"
14 0.070 3.317 0.9769.3363.0941.3341.16914.8060.001590.5388.5092.0155.529 3.907
12 0.105 4.976 1.46313.8763.079 2.039 1.18022.5000.005381.05513.5983.354 9.20412.437
8" x 3"
14 0.070 3.555 1.045610.4373.160 2.111 1.42022.3660.001700.552 9.116 2.106 5.780 3.907
12 0.105 5.333 1.56815.5133.145 3.219 1.43333.9200.005761.054114.4303.447 9.46112.437
14 0.070 3.793 1.11611.5373.2163.1391.67831.8930.001820.5569.6102.1625.933 3.907
8" x 3 /2" 1
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
12 0.105 5.690 1.67317.1493.201 4.780 1.69048.2840.006151.02214.8563.408 9.35412.437
9" x 3"
14 0.070 3.793 1.11613.7253.508 2.111 1.37629.1620.00182 0.554 11.8922.429 6.665 3.446
12 0.105 5.690 1.67320.4273.494 3.219 1.38744.2440.006151.06219.0324.05111.11811.728
9" x 3 /2" 14 0.070 4.031 1.18615.1213.571 3.139 1.62741.6620.001940.55912.3412.431 6.671 3.446
1
12 0.105 6.047 1.77822.5043.557 4.780 1.64063.0990.006541.03019.5824.01211.01211.728
10" x 21/2" 14 0.070 3.793 1.11615.8463.796 1.334 1.09424.3480.001820.54214.1042.625 7.203 3.083
12 0.105 5.690 1.67323.6073.756 2.039 1.10437.0310.006151.07023.1394.57112.54510.483
10" x 3"
14 0.070 4.031 1.18617.5713.850 2.111 1.33436.9460.001940.55614.8602.681 7.357 3.038
12 0.105 6.047 1.77826.1773.837 3.220 1.34656.0740.006541.06824.4314.69112.87410.483
10" x 31/2" 12 0.105 6.404 1.88328.7483.907 4.781 1.59380.1100.006921.03625.1234.65312.77010.483
10" x 4"
14 0.070 4.507 1.32621.0223.982 4.455 1.83372.4130.002170.56215.8842.686 7.372 3.083
12 0.105 6.761 1.98831.3183.969 6.775 1.846109.550.007311.10227.1434.99513.70810.483
12" x 2 /2" 1
12 0.105 6.404 1.88336.6854.413 2.039 1.04155.4690.006921.07935.9805.92916.273 8.646
12" x 3"
14 0.070 4.507 1.32627.0774.520 2.111 1.26255.5200.002170.55921.9093.188 8.750 2.546
12 0.105 6.761 1.98840.3994.508 3.220 1.27384.3130.007311.07737.8336.07716.678 8.646
12" x 3 /2" 1
12 0.105 7.118 2.09344.1134.591 4.781 1.511120.840.007691.04538.8606.04216.583 8.646
800.406.7387
(Corporate Office)
iMetal.net - Phone:
267-983-1017
- www.iMetal.net
PSF-21
secondary framing
Dimensions and Section Properties of Cees
B1
Fy = 55.0 KSI
R = 0.125 In
WEB
B2
Full Section Properties
SIZE
Thickness Weight
in
plf
Web x Flange GA
A
In2
Ix-x
in4
rx
in
Iy-y
in4
ry
in
Cw
in6
Effective Section Properties
(Fully Braced) X-X Axis
J
In4
Ae
in2
Ixe
in4
Sxe
in3
Max
K-ft
Vay
Kips
16 0.057 1.926 0.5661.509 1.633 0.5150.9532.0581
0.000613
0.40641.3780.647 1.776 3.665
4" x 21/2"
14 0.070 2.365 0.6961.8351.6240.6300.3522.5640.0011360.5401.7140.8152.381 5.367
16 0.057 2.314 0.6803.8402.3760.5950.9354.5300.0007390.4153.5211.1113.049 2.865
6" x 21/2"
14 0.070 2.841 0.8364.6872.3680.7290.9345.6040.0013650.5554.3781.3953.829 5.331
16 0.057 2.701 0.7947.5323.0790.6520.9069.3280.000860.4186.8231.6034.400 2.102
8" x 21/2"
14 0.070 3.317 0.9769.2103.0720.8000.90610.2700.001590.5628.6262.0725.686 3.907
12 0.105 4.9756 1.46313.6493.054 1.196 0.90415.5610.0053781.10413.6493.412 9.36512.437
8" x 3"
14 0.070 3.555 1.04610.3113.1401.2431.09015.767
0.0017080.5839.3062.1866.000 3.907
12 0.105 5.3329 1.56915.2863.122 1.863 1.09023.9450.0057641.13414.8953.65510.03012.437
14 0.070 3.793 1.11611.4113.1981.8081.27322.735
0.0018220.5949.8802.2666.219 3.907
8" x 3 /2" 1
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
12 0.105 5.6899 1.67316.9223.179 2.712 1.27334.5690.0061501.09515.3713.616 9.92412.437
9" x 3"
14 0.070 3.7930 1.11613.5823.489 1.289 1.07520.3730.001820.58512.2562.562 7.031 3.446
12 0.105 5.68961.673420.1683.472 1.933 1.07530.8680.006151.14219.6494.28811.76911.728
9" x 3 /2" 14 0.070 4.0310 1.18614.9773.554 1.877 1.25829.3750.0019370.59612.8252.594 7.119 3.446
1
12 0.105 6.0466 1.77822.2453.537 2.818 1.25944.5610.0065361.10220.2484.24611.65411.728
10" x 21/2" 14 0.070 3.793 1.11615.6853.750 0.853 0.87416.7350.0018220.56614.4362.739 7.516 3.083
12 0.105 5.6896 1.67323.3163.733 1.277 0.87425.2560.0061501.11823.3164.66312.79810.483
10" x 3"
14 0.070 4.031 1.18617.4103.832 1.330 1.05925.7010.0019370.58715.3232.826 7.757 3.038
12 0.105 6.0466 1.77825.8873.815 1.995 1.05938.8750.0065361.14825.2214.95813.60610.483
10" x 31/2" 12 0.105 6.404 1.88328.4573.887 2.912 1.24356.1220.006921.10925.9584.91313.48510.483
10" x 4"
14 0.070 4.507 1.32620.8623.967 2.692 1.42551.0300.002170.60216.5862.879 7.901 3.083
12 0.105 6.7606 1.98831.0273.950 4.045 1.42677.3220.007311.16127.8005.20314.28010.483
12" x 2 /2" 1
12 0.105 6.404 1.88336.3314.392 1.340 0.84337.8370.006921.12736.3316.05516.618 8.646
12" x 3"
14 0.070 4.507 1.32626.8814.503 1.398 1.02738.6190.002170.58922.6163.358 9.217 2.546
12 0.105 6.7606 1.98840.0454.488 2.099 1.02758.2860.007311.15739.0256.40117.567 8.646
12" x 3 /2" 1
12 0.105 7.118 2.09343.759 4.572 3.072 1.211 84.1770.00769 1.118 40.0896.358 17.441 8.646
PSF-22
800.406.7387
(Corporate
iMetal.net
- Phone:
secondary framing
Maximum Reaction for Zees and Cees
Flange
Flange
Web
Web
Flange
Web of
C or Z
Ga.
Flange
End Bearing (kips)
Interior Bearing (kips)
Length of Bearing
Length of Bearing
2"3"4"5"6" 2"3" 4"5" 6"
16 0.650.7350.820.900.99 1.321.4521.6151.822.02
4"
14 1.09 1.211.331.451.572.0372.21 2.38 2.612.87
16 0.6 0.680.760.840.91 1.251.37 1.53 1.721.92
6"
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
14 1.03 1.141.251.371.48 1.952.11 2.28 2.502.75
16 0.56 0.630.700.770.84 1.181.30 1.44 1.631.81
8"
14 0.96 1.071.181.281.89 2.872.02 2.18 2.392.63
12 2.56 2.772.973.183.38 4.454.71 4.97 5.235.49
10"
14 0.9 1.0 1.1 1.201.30 1.781.93 2.08 2.282.51
12 2.46 2.662.833.053.25 4.324.57 4.83 5.085.33
1. Above values have been calculated in accordance with 2001 AISI Specification, Eq. C3.4-1 (End Reaction) and
Eq. C3.4-4 (Interior Reaction).
PSF-28
800.406.7387
(Corporate
iMetal.net
- Phone:
secondary framing
Allowable Uniform Loads
GENERAL NOTES
W - LB/FT
W - LB/FT
3"
3"
6"
3"
L
L
L
3"
TWO SPAN
SIMPLE SPAN
W - LB/FT
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
6"
6"
3"
L
L
L
3"
6"
L
THREE OR MORE SPANS
1. Tabulated values are allowable superimposed loads (PLF) on normal 1/2:12 to 4:12 roof pitches. Purlin weights have not been subtracted from them. They meet or exceed L/180 deflection criteria as indicated in the tables.
2. Weight of roofing material and other dead loads must be subtracted from tabulated values of purlins to determine net live load capabilities.
3. Allowable loads have been calculated in accordance with the 2001 edition of AISI Specifications. These values are valid only
if the compression flange of the section is adequately supported laterally.
4. Consult with your engineer or architect for design applications such as very low or very high roof pitches (1/4:12, over 4:12), floating SSR, and for uplift (suction) criteria. Sag rods of angle bracing are usually required when members are not laterally supported by sheeting on the compression flange.
5. For continuous girts, wind load values can be obtained by multiplying tabulated values by 1.333.
6. End bearing capacity must be checked using actual load, bearing lengths, and the bearing chart.
7. For full member capacity, 1/2" diameter A-325 bolts are recommended for all lap bolts.
8. Web stiffeners can be provided by welding or bolting a clip plate to the support rafters and connecting the purlins through the web holes to the clip.
9. Tabulated values are based on a 6" bearing at interior supports. Reaction at end supports can be approximated by
the following equations:
Simple Span
R = 0.50WL
2 Spans
R = 0.375WL
3 or More Spans R = 0.40WL
10. Maximum live loads for deflection ratios other than L/180 can be calculated using the values tabulated as follows:
For L/240: Max. LL (PLF) = (180/240) x (Tabulated Value).
For L/360: Max. LL (PLF) = (180/360) x (Tabulated Value).
800.406.7387
(Corporate Office)
iMetal.net - Phone:
267-983-1017
- www.iMetal.net
PSF-29
secondary framing
Allowable Uniform Loads in Pounds per Linear Foot
LOAD TABLES FOR STANDARD ZEES AND CEES
(Symmetrical Flanges Only)
Flange
Flange
Web
Web
Flange
Section
Flange
Span in
Feet
Simple Span (plf)
Defl. (L/180)
Controlling
Stress
Controlling
16 Ga
14 Ga
16 Ga
8
213
272
9
168
215
10
136
174
14 Ga
149
11
113144102112
95
121
79
86
4" x 21/2" 12
81
103
62
68
Cee or 13
Zee
14
70895054
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
15
61774044
16
53683336
17
47602830
18
42542326
Span in
Section
Feet
Simple Span (plf)
Defl. (L/180)
Controlling
Stress
Controlling
16 Ga
14 Ga
16 Ga
10
234
298
14 Ga
11
193
246
12
163
207
13
139
176
16
91
116
84
102
17
81
103
70
85
6" x 21/2" 14
119
152
Cee or
15
104132101124
Zee
18
72925972
20
59744352
Notes:
1. Tabulated values are allowable superimposed loads. Purlin and all other load weights have not been subtracted from them.
2. Allowable loads have been calculated in accordance with 2001 AISI Specifications.
3. Bearing must be checked using actual bearing length and loads.
4. Wind loads can be obtained by multiplying tabulated values by 1.33.
5. Tabulated values are valid only if the compression flange of the section is adequately supported laterally.
PSF-30
800.406.7387
(Corporate
iMetal.net
- Phone:
secondary framing
Flange
Flange
Web
Web
Flange
Flange
Simple Span (plf)
Span in
Section
Feet
Defl. (L/180)
Controlling
Stress
Controlling
16 Ga
14 Ga
12 Ga
16 Ga
14 Ga
12 Ga
15
148
197
327
16
130
173
288
17
115
153255247
18
102
137227208
92
123
204
119
177
8" x 2 /2" 19
Cee or 20
83111184102
152
1
Zee
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
217510016772 88131
22
69911526377114
2363 84 13955 67180
24
5877128485988
25
5371 118435278
Section
Span in
Feet
Simple Span (plf)
Defl. (L/180)
Controlling
Stress
Controlling
14 Ga
12 Ga
14 Ga
15
206
336
16
181
296
17
160
262
12 Ga
257
18
143234137217
8" x 3" 19
Cee or 20
Zee
21
22
128
210
116
184
116
189
100
158
105
172
86
136
96
156
75
119
23
8714366104
24
80
131
58
91
25
74
121
51
81
Notes:
800.406.7387
(Corporate Office)
iMetal.net - Phone:
267-983-1017
- www.iMetal.net
PSF-31
secondary framing
Flange
Flange
Web
Web
Flange
Section
Flange
Span in
Feet
Simple Span (plf)
Defl. (L/180)
Controlling
Stress
Controlling
14 Ga
12 Ga
14 Ga
15
211
333
16
185
292
17
164
259
18
146
231
8" x 3 /2" 19
Cee or 20
131
207
119
187
21
108
170
1
12 Ga
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
Zee
162
22
9815598141
23
9014183123
24
8213073109
25
Span in
Section
Feet
76
120
65
96
Simple Span (plf)
Defl. (L/180)
Controlling
Stress
Controlling
14 Ga
12 Ga
14 Ga
14
272
454
16
208
347
18
165
275
20
133
222
12 Ga
110
184
168
9" x 3" 22
Cee or 24
9315487129
Zee
26
7913268102
28
68
113
55
81
30
59994566
32
52873755
34
46773146
Notes:
PSF-32
800.406.7387
(Corporate
iMetal.net
- Phone:
secondary framing
Flange
Flange
Web
Web
Flange
Flange
Span in
Section
Feet
Simple Span (plf)
Defl. (L/180)
Controlling
Stress
Controlling
14 Ga
12 Ga
14 Ga
14
272
449
12 Ga
16
208
344
18
165
272
20
133
220
9" x 3 /2" 22
Cee or 24
Zee
26
101
182
93
153
143
79
130
75
112
28
68
112
60
90
1
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
30
59984973
32
52864060
34
46763450
Span in
Section
Feet
Simple Span (plf)
Defl. (L/180)
Controlling
Stress
Controlling
14 Ga
12 Ga
14 Ga
14
294
512
12 Ga
16
225
392
18
178
310
20
144
251
10" x 21/2" 22
Cee or 24
Zee
26
119
207
194
100
174
150
85
148
79
118
28
74
128
63
94
30
64
112
51
77
32
56984263
34
50873553
Notes:
800.406.7387
(Corporate Office)
iMetal.net - Phone:
267-983-1017
- www.iMetal.net
PSF-33
secondary framing
Flange
Flange
Web
Web
Flange
Section
Flange
Span in
Feet
Simple Span (plf)
Defl. (L/180)
Controlling
Stress
Controlling
14 Ga
12 Ga
14 Ga
12 Ga
14
300
525
16
230
402
18
182
318
20
147
257
10" x 3" 22
Cee or 24
122
213
102
179
166
26
87
152
130
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
Zee
28
7513170104
30
65
114
57
85
32
57
101
47
70
34
51893958
Span in
Section
Feet
Simple Span (plf)
Stress
Controlling
Defl. (L/180)
Controlling
12 Ga
12 Ga
14
664
16
509
18
402
20
325
12" x 21/2" 22
Cee or 24
Zee
26
269
193
183
28
166
146
30
145
119
32
127
98
34
113
82
226
Notes:
PSF-34
800.406.7387
(Corporate
iMetal.net
- Phone:
secondary framing
Flange
Flange
Web
Web
Flange
Flange
Span in
Section
Feet
Simple Span (plf)
Defl. (L/180)
Controlling
Stress
Controlling
14 Ga
12 Ga
14 Ga
14
357
680
16
273
521
18
216
411
20
175
333
12" x 3" 22
Cee or 24
Zee
26
144
275
121
231
103
197
12 Ga
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
28
89
170
160
30
77
148
130
32
68
130
107
34
60
115
89
Notes:
800.406.7387
(Corporate Office)
iMetal.net - Phone:
267-983-1017
- www.iMetal.net
PSF-35
secondary framing
LOAD TABLES FOR STANDARD ZEES
Flange
2'-4" Lap
Web
Long Lap
Flange
Long Lap - 2 Spans
Long Lap - 3 Spans
Span in
Defl. (L/180)
Stress
Stress
Defl. (L/180)
Section
Feet Controlling, plf Controlling, plf Controlling, plf Controlling, plf
16 Ga 14 Ga 16 Ga 14 Ga 16 Ga 14 Ga 16 Ga 14 Ga
12 139
177155
198194
14
Z4" x 21/2" 16
96122 11314499121
70 90 8611066 81
18 5368 68864656
Long Lap - 2 Spans
Long Lap - 3 Spans
Span in
Stress
Stress
Defl. (L/180)
Defl. (L/180)
Section
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
14 153
202195
240
16 115
149145
189
Z6" x 21/2" 18 88
114112
146142
20
Span in
Section
Feet
70 91 8911684102
Long Lap - 2 Spans
Stress
Controlling, plf
Defl. (L/180)
Controlling, plf
Long Lap - 3 Spans
Stress
Controlling, plf
Defl. (L/180)
Controlling, plf
16 Ga 14 Ga 12 Ga 16 Ga 14 Ga 12 Ga 16 Ga 14 Ga 12 Ga 16 Ga 14 Ga 12 Ga
16
139205370 174261436
18
110160286 140203360
20
90 128226 115163285
22
74 105184 95 134232
225
Z
24 6387
151 80
111
192 170
8" x 21/2"
25 5880
139 73
102
175 152
26
53 74128 68 94162 90 135
28
46 64109 58 80123 72 120
30 405594 50691184863 93
Notes:
PSF-36
800.406.7387
(Corporate
iMetal.net
- Phone:
secondary framing
Flange
2'-4" Lap
Web
Long Lap
Flange
Long Lap - 2 Spans
Long Lap - 3 Spans
Span in
Stress
Defl. (L/180)
Stress
Defl. (L/180)
Section
18
165
292
211
370
20 133
231169
293
22 109
188138
238
Z8" x 3"
24 91
155115
196193
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
25 83
142106
180171
26 77
131 97165146
28
66 111 83 14181 121
30 5796 721216698
Long Lap - 2 Spans
Section
Long Lap - 3 Spans
Span in
Stress
Defl. (L/180)
Stress
Defl. (L/180)
18 169
289215
367
20 136
229173
290
22 112
186142
235
2493
154
118
194
Z8" x 31/2" 25 86
141108
178
26 79
129100
163
28
68110 85 139 134
30 58
9574
120
73
108
Notes:
800.406.7387
(Corporate Office)
iMetal.net - Phone:
267-983-1017
- www.iMetal.net
PSF-37
secondary framing
Flange
2'-4" Lap
Web
Long Lap
Flange
Long Lap - 2 Spans
Long Lap - 3 Spans
Span in
Defl. (L/180)
Stress
Stress
Defl. (L/180)
Section
18 179
338226
429
20 146
268185
341
22 120
218153
277
Z9" x 3"
24 101
181128
229
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
2593
166
118
210
26 86
152109
193
28 74
130 94164159
30
64112 81 142 129
Long Lap - 2 Spans
Section
Long Lap - 3 Spans
Span in
Stress
Stress
Defl. (L/180)
Defl. (L/180)
18 179
335226
425
20 146
266185
337
22 120
216153
274
24 101
179128
227
Z9" x 31/2" 2593
164
118
208
26 86
151109
191
2874
129
94
163
3064
111
81
140
Notes:
PSF-38
800.406.7387
(Corporate
iMetal.net
- Phone:
secondary framing
Flange
2'-4" Lap
Web
Long Lap
Flange
Long Lap - 2 Spans
Long Lap - 3 Spans
Span in
Stress
Defl. (L/180)
Stress
Defl. (L/180)
Section
20 149
297186
377
22 124
242156
307
24 105
202132
255
25 97
185122
234
Z10" x 21/2" 2690
170
113
215
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
28
78145 98 184
30 68
126 86159151
32
59110 75 138 123
Long Lap - 2 Spans
Section
Long Lap - 3 Spans
Span in
Stress
Defl. (L/180)
Stress
Defl. (L/180)
20 152
300188
388
22 128
245158
318
24 107
207134
262
Z-10" x 3"
25 100
190125
240
26 92
175116
221
28 79
149101
189
30
69129 88162
32 61
113 77
142136
Notes:
800.406.7387
(Corporate Office)
iMetal.net - Phone:
267-983-1017
- www.iMetal.net
PSF-39
secondary framing
Flange
2'-4" Lap
Web
Long Lap
Flange
Long Lap - 2 Spans
Long Lap - 3 Spans
Span in
Stress
Defl. (L/180)
Defl. (L/180)
Stress
Section
12 Ga
12 Ga
20
358
456
22
296
376
24
248
315
25
Z1
12" x 2 /2" 26
229
290
211
268
28
182
230
30
158
200
32
138
175
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
Long Lap - 2 Spans
Long Lap - 3 Spans
Span in
Stress
Defl. (L/180)
Stress
Defl. (L/180)
Section
20 155
365184
463
22 132
302158
384
24 113
254137
322
25 106
234127
296
Z12" x 3" 2698
216
119
273
28 86
186105
235
3076
161
93
204
3267
141
83
179
Notes:
PSF-40
800.406.7387
(Corporate
iMetal.net
- Phone:
secondary framing
Flange
3'-6" Lap
Web
Flange
Max Lap
Max Lap - 2 Spans
Section
Max Lap - 3 Spans
Span in
Stress
Stress
Defl. (L/180)
Defl. (L/180)
10 226
288229
292
12 160
204157
201198
14
119 152 115 147101 124
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
Z16
4" x 21/2"
84107 87 11266 82
18 6280 69 884757
20 4861475755 713441
22 3844354145 582531
Max Lap - 2 Spans
Section
Max Lap - 3 Spans
Span in
Stress
Defl. (L/180)
Stress
Defl. (L/180)
14 185
250190
250
16 135
178152
193
18 103
135115
150140
Z20
6" x 21/2"
80104 95 12285105
22 6483 791006378
24 5368 66 834860
25 4862 61 774353
Notes:
800.406.7387
(Corporate Office)
iMetal.net - Phone:
267-983-1017
- www.iMetal.net
PSF-41
secondary framing
Flange
3'-6" Lap
Web
Max Lap
Flange
Max Lap - 2 Spans
Span in
Section
Feet
Stress
Controlling, plf
Defl. (L/180)
Controlling, plf
Max Lap - 3 Spans
Stress
Controlling, plf
Defl. (L/180)
Controlling, plf
16 Ga 14 Ga 12 Ga 16 Ga 14 Ga 12 Ga 16 Ga 14 Ga 12 Ga 16 Ga 14 Ga 12 Ga
16
156240435 205286470
18
126183330 161225370
20
101145250 130180301
22 83
118
204106
147
246 226
Z
24 6997
166 88
123
208118176
8" x 21/2"
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
25 6388
153 81
113
190103154
26 5981
139 74
103
176 92137
28
50 67118 64 8815159 72 110
30
43 59102 54 7512848 59 89
Max Lap - 2 Spans
Max Lap - 3 Spans
Span in
Stress
Stress
Defl. (L/180)
Defl. (L/180)
Section
18 189
339234
383
20 150
264188
309
22
121
211
155
252
Z8" x 3"
24 100
172128
213197
25 92
157117
196174
26 84
144107
181
103
154
28
72121 91 15482123
30
62 104 78 13267 99
Notes:
PSF-42
800.406.7387
(Corporate
iMetal.net
- Phone:
secondary framing
Flange
3'-6" Lap
Web
Max Lap
Flange
Max Lap - 2 Spans
Max Lap - 3 Spans
Span in
Stress
Defl. (L/180)
Stress
Defl. (L/180)
Section
16 250
448300
480
18 194
337240
380
20 154
260193
300
22 124
210158
250
Z24 102
170130
212
8" x 31/2"
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
25 94
155120
194190
26 86
142110
180168
28
74120 93 15290135
30
63 102 81 13073 110
Max Lap - 2 Spans
Max Lap - 3 Spans
Span in
Stress
Stress
Defl. (L/180)
Defl. (L/180)
Section
18 202
391261
449
20 163
305209
363
22 133
245171
299
Z9" x 3"
24 111
201142
250
25 102
183130
230229
26 94
167119
212203
28 80
142102
180162
30 69
122 88154131
32
60
105
77
133
72
108 Notes:
800.406.7387
(Corporate Office)
iMetal.net - Phone:
267-983-1017
- www.iMetal.net
PSF-43
secondary framing
Flange
3'-6" Lap
Web
Flange
Max Lap
Max Lap - 2 Spans
Max Lap - 3 Spans
Span in
Stress
Defl. (L/180)
Stress
Defl. (L/180)
Section
18 203
387261
445
20 163
303209
359
22 133
243171
296
24 111
199142
248
Z1
9" x 3 /2" 25 102
181130
228
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
26 94
166120
210
28 80
140102
178
30 69
120 88152144
Max Lap - 2 Spans
Max Lap - 3 Spans
Span in
Stress
Defl. (L/180)
Stress
Defl. (L/180)
Section
20
166
336
211
410
22 136
271176
337
24 115
223147
282
25 106
204135
258
Z10" x 21/2" 26 98
187125
237235
28 84
158107
201187
30 73
136 93172152
32
64118 81 149 124
Notes:
PSF-44
800.406.7387
(Corporate
iMetal.net
- Phone:
secondary framing
Flange
3'-6" Lap
Web
Flange
Max Lap
Max Lap - 2 Spans
Section
Max Lap - 3 Spans
Span in
Stress
Defl. (L/180)
Stress
Defl. (L/180)
18 205
435260
520
20 168
345213
420
22 140
242176
350
Z
24 117
228150
290
10" x 3"
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
25 106
208138
265
26 100
190127
245
28 86
162108
205
Section
Max Lap - 2 Spans
Max Lap - 3 Spans
12 Ga
12 Ga
Span in
Stress
Defl. (L/180)
Defl. (L/180)
Stress
20
401514
22
328419
24
273
348
25
Z12" x 21/2" 26
250
319
231
293
28
197
250
30
170
216
32
148
188
Notes:
800.406.7387
(Corporate Office)
iMetal.net - Phone:
267-983-1017
- www.iMetal.net
PSF-45
secondary framing
Flange
3'-6" Lap
Web
Flange
Max Lap
Max Lap - 2 Spans
Section
Max Lap - 3 Spans
Span in
Stress
Defl. (L/180)
Stress
Defl. (L/180)
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
20 170
410200
520
22 143
335175
430
24 123
280150
350
Z
25 114
255140
325
12" x 3"
26 105
235131
300
2893
202
115
260
30 81
194100
220
Notes:
PSF-46
800.406.7387
(Corporate
iMetal.net
- Phone:
secondary framing
LGSI Information
The 2001 revision of the AISI specifications made it necessary for manufacturers of light gauge structural sections to make substantial revisions to their design properties, load table, and other published data.
In an effort to answer the requirements mandated by this code revision, several manufacturers formed the Light Gauge Structural
Institute in 1989. The Light Gauge Structural Institute is a nonprofit organization comprised of member companies who are in the
business of manufacturing light gauge cold-formed sections. This manual is the result of an effort to develop uniform information
about light gauge structural sections.
Companies that are members of the Light Gauge Structural Institute conform to a set of bylaws and standards that ensure their
compliance with the various policies set forth by the institute including, but not limited to, annual unannounced inspections that
allow members to receive certification of compliance.
The AISI code revisions created a need to investigate light gauge structural sections in a manner not previously addressed. As a
part of this investigation, sections with unequal flanges were considered; and as a result of considerable design analysis and study,
it became obvious that unequal flanges offered considerable advantages, particularly due to the number of applications that were
lapped.
Metal Sales also manufactures other light gauge structural sections that are not included in the scope of this manual. Metal
Sales will provide information for these shapes unique to their operation. However, a requirement of the Light Gauge Structural
Institute is that these shapes be designed in the same manner and using the same criteria applied to the sections in the Light Gauge
Structural Steel Framing System Design Handbook.
Section properties, section allowables, load tables and sample calculations are available in the "Light Gauge Structural Steel
Framing System Design Handbook". Please refer to the latest edition of this handbook when inquiring about Light Gauge Structural Institute criteria.
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
Light Gage Structural Steel
Framing System Design
Handbook
Volume 1
800.406.7387
(Corporate Office)
iMetal.net - Phone:
267-983-1017
- www.iMetal.net
PSF-47
secondary framing
LGSI Zee Information
LGSI Secondary Framing (members with unsymmetrical flanges) are available in 4", 6", 8", 9", 10", and 12" web sizes and available in 21/8" x 23/8", 25/8" x 27/8", 31/8" x 33/8", and 35/8" x 37/8" flange sizes. Metal Sales offers members in various gauges and
finishes. In addition, members can be ordered to your desired length with standard or custom punching. For your specific loading
requirements please reference Metal Sales' Technical Reference Product Manual.
Bolt
Bolt
OR
Purlin
Clip
Attached inverted purlins
to beam with clip
Attached purlins to
beam with flange bolt
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
Lapped Purlins
Triangle punch in LGSI Purlin reflects where larger flange is located.
PSF-48
800.406.7387
(Corporate
iMetal.net
- Phone:
secondary framing
LGSI Zee Lap Information (cont.)
LONG LAP
For Zees Only
2' - 31/2"
TWO SPAN
Zee
2' - 31/2"
Lapped
Section
lapped
section
FOUR SPAN
2' - 31/2"
2' - 31/2"
2' - 31/2"
lapped
section
lapped
section
lapped
section
2' - 31/2"
2' - 31/2"
2' - 31/2"
2' - 31/2"
2' - 31/2"
lapped
section
lapped
section
lapped
section
lapped
section
lapped
section
punch pattern #A, #D, or #F.
SIX SPAN
MAX LAP
For Zees Only
4' - 31/2"
Zee
TWO SPAN
4' - 31/2"
lapped
section
FOUR SPAN
4' - 3 /2"
1
lapped
section
SIX SPAN
4' - 31/2"
lapped
section
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
4' - 31/2"
4' - 31/2"
Lapped
Section
punch pattern #A or #D.
lapped
section
lapped
section
4' - 31/2"
4' - 31/2"
4' - 31/2"
4' - 31/2"
lapped
section
lapped
section
lapped
section
lapped
section
STANDARD LAP
For Zees Only
2'-31/2"
4' - 31/2"
Zee
Zee
Lapped
Section
punch pattern #A or #D.
FOUR SPAN
2'-31/2"
4' - 31/2"
lapped
section
lapped
section
lapped
section
4' - 31/2"
2'-31/2"
2'-31/2"
2'-31/2"
lapped
section
lapped
section
lapped
section
lapped
section
4' - 31/2"
Lapped
Section
SIX SPAN
4' - 31/2"
lapped
section
800.406.7387
(Corporate Office)
iMetal.net - Phone:
267-983-1017
- www.iMetal.net
PSF-49
secondary framing
SUPER LAP
For Zees Only
6' - 31/2"
Zee
Lapped
Section
TWO SPAN
punch pattern #B, #E, or #H.
6' - 31/2" Lap
Lapped
Section
EXTENDED LAP
For Zees Only
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
4' - 31/2"
6' - 31/2"
Zee
Lapped Section
Lapped Section
punch pattern #B or #E.
FOUR SPAN
6' - 31/2"
4' - 31/2"
6' - 31/2"
Lapped Section
Lapped Section
Lapped Section
SIX SPAN
6' - 31/2"
Lapped Section
SIMPLE SPAN
PSF-50
Zee
4' - 31/2"
4' - 31/2"
4' - 31/2"
6' - 31/2"
Lapped Section
Lapped Section
Lapped Section
Lapped Section
For Zees Only
800.406.7387
(Corporate
iMetal.net
- Phone:
secondary framing
LGSI LONG LAP
For Zees Only
2' - 31/2" Lap
1'-0"
2" 2"
1'-0"
punch pattern #A, #D, or #F.
LGSI MAX LAP
For Zees Only
4' - 31/2" Lap
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
2'-0"
2" 2"
2'-0"
punch pattern #A, #D, or #G.
LGSI SUPER LAP
For Zees Only
6' - 31/2" Lap
3'-0"
2" 2"
3'-0"
punch pattern #B, #E, or #H.
800.406.7387
(Corporate Office)
iMetal.net - Phone:
267-983-1017
- www.iMetal.net
PSF-51
secondary framing
Use Eave Strut
Punch Patterns:
#S 3 C
#S 3 D
#S 4
#S 5
See Page PSF-13 for
information.
.5"
3"
Holes punched at center point of
member for bracing or sag rods.
DISTRIBUTED BY:
www.iMETAL.net
PHONE: 267-983-1017
Vertical Slots or Holes
for beam attachment.
EAVE STRUT NOTES
1. Single Slope, Double Slope, or Universal Eave Struts are available, please specify.
2. Before ordering Eave Struts, you must subtract 1/2" from bay width.
PSF-52
800.406.7387
(Corporate
iMetal.net
- Phone:
Punch Pattern
similar on both
ends

DISTRIBUTED BY: www.iMETAL.net PHONE: 267-983-1017

Transcription

Similar documents