Installation Instructions Tubular Lockset Diagram Door Preparation

®
Installation Instructions
TL3700 Series
Tubular Lockset
In U.S.:
Corbin Russwin, Inc.
225 Episcopal Road
Berlin, CT 06037 USA
www.corbinrusswin.com
ASSA ABLOY
In Canada:
ASSA ABLOY Door Security Solutions Canada
160 Four Valley Drive
Vaughan, Ontario, Canada L4K4T9
www.assaabloy.ca
Technical Product Support: Phone: 888-607-5703
Tubular Lockset Diagram
1
5
2
13
6
7
1
12
14
3
2
3
6
4
5
9
11
10
Parts List
1 Lever
2 Set Screw
3 Rose
4 Mounting Post
5 Spring Housing
6 Spindle
7 Latch
(2)
(2)
(2)
(2)
(2)
(2)
(1)
8
9
10
11
12
13
14
Faceplate
Screws-Latch & Strike #8-32 x 3/4"
Strike
Strike Box
Push Button (TL3720 only)
Mounting Post Screw
Fire Guard Clip (Fire Rated option only)
(1)
(4)
(1)
(1)
(1)
(2)
(1)
Tools Required For Assembly
#2 Phillips Screwdriver
3/32" Hex Wrench
1/8" Drill Bit
2-1/8" Bore
1" Bore
Door Preparation
Use Door Marker supplied in box. Information below is for reference only.
Final Door Prep
Mark and Drill Holes
IMPORTANT:
Fold template onto high
edge of door bevel
Centerline of
latch front and
strike
1"
(25mm)
hole
2-1/8"
(54mm)
hole
Template
2-1/4"
(57mm)
Backset
must match lock
Frame Prep for Strike
Screws (2)
#8-32 x 3/4"
Door
Bevel
38" from
Finished Floor
1-1/8"
(29mm)
DOOR
FRAME
FM271 (09/12)
Copyright © 2012 Corbin Russwin Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
Permission of Corbin Russwin, Inc. is prohibited.
1 of 3
®
TL3700 Series Tubular Lockset
Latch Installation
Lock & Trim Installation
1
2
Install first for fire
rated option only.
ASSA ABLOY
IMPORTANT
Test for proper
operation before
closing door
Mounting Post Screws (2)
#6 x 3/4"
Install loosely;
tighten after step #2
Screws (2)
#8-32 x 3/4"
Rose
Align studs on rose with
bushings on spring housing.
Push on rose to install.
Note: TL3720
The threaded hole on locking
piece must be to the inside of
the door, so the Push Button
(Detail #12) can be threaded
into it.
Note: Rose to be removed
with a flat head screwdriver at notch.
For square rose installation, see page 3.
Dummy Trim Installation (TL3750 / TL3770)
Note: Only (2) door prep holes are required for Dummy Trim.
See door marker supplied in box for further details.
1
3
5
#7 O/S Thru-Bolt Plate Assembly
is only used for the TL3750.
7
DO
OR
2
6
6
3
2
4
Align studs on rose with
bushings on mounting plate.
Push on rose to install.
1
Parts List
1 Lever
2 Set Screw
3 Rose Assembly
4 Mounting Post
2 of 3
(2)
(2)
(2)
(2)
5 Mounting Post Screw
6 Mounting Plate Assembly
7 O/S Thru-Bolt Plate Assembly
(TL3750 only)
Copyright © 2012 Corbin Russwin Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
(2)
(2)
(1)
FM271 (09/12)
®
TL3700 Series Tubular Lockset
Square Rose Installation
ASSA ABLOY
1
Figure 1
NOTE: To level plate, place a right angle square
on the flat portion of the mounting plate.
1
Pilot
Hole
3
5
Pilot Hole
2
Spring Housing
Square Mounting Plate
4
Parts List
1 Square Mounting Plate
2 #6 x 3/4" Machine Screws
3 Rose
4 Lever
5 Set Screw
(1)
(2)
(1)
(1)
(2)
Tools Required For Assembly
Drill
Pilot Bit
Phillips Screwdriver
Right Angle Square
1. Install lock per instructions on page 2.
a. Square rose installation begins after spring housing installation.
2. Position square mounting plate over spring housing as seen in Figure 1.
3. Drill two centered pilot holes for the #6 mounting screws in the upper right and lower
left portions of the square mounting plate.
4. Loosely attach mounting plate to both sides of the door with screws.
5. Square top surface of mounting plate to edge of door.
a. NOTE: The square edge MUST be on the flat surface of the square mounting plate for
proper leveling.
6. Tighten mounting screws.
7. Press rose onto mounting plate, fasten lever with set screw.
FM271 (09/12)
Copyright © 2012 Corbin Russwin Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
Permission of Corbin Russwin, Inc. is prohibited.
3 of 3