Assembly Instructions

Cook's Corner Kitchen
Assembly Instructions
Item #3950
© 2010 Melissa & Doug, LLC
All rights reserved
1011
We care about your comments
Please call us! 1-800-284-3948
www.MelissaAndDoug.com
Cook's Corner Kitchen
PARTS
D
A
E
Q
I
(2 pieces)
N
R
B
(2 pieces)
F
J
S
(3 pieces)
K
O
T
C
G
L
H
Item #3950
M
Page 2
P
(2 pieces)
U
Cook's Corner Kitchen
HARDWARE
9
10
(2 pieces)
5
3
1
(27 pieces)
(2 pieces)
7
(8 pieces)
(19 pieces)
(31 pieces)
NOTE: The (5) Screw
is a little shorter
than the (4) Screw
2 (11 pieces)
4 (8 pieces)
6 (10 pieces)
8
11 (4 pieces)
(3 pieces)
(Note that some packages of hardware may have extra pieces)
(Items above this line are shown full size)
17
(4 pieces)
12
13
Item #3950
18
14
(4 pieces)
15 (2 pieces)
16
Page 3
20
19
HINTS and TIPS
Cook's Corner Kitchen
This part is a Barrel Nut (3)
It is used to join the main wood
panels together with a screw.
The threaded hole in it should be
turned to make it easy for the
screw to attach. Using a screwdriver as shown will help to turn
the barrel nut so the hole is
lined up with the screw.
This part is a Locknut (7)
It is used in several places
and should be held with the
included wrench while assembling
with a screwdriver as shown.
When tightened properly, it will
prevent the screw from
loosening during play.
Item #3950
(Included Wrench)
Page 4
Lay out all the parts you will need
for each step. The parts are labeled
in alphabetical or numerical order by
the step.
Cook's Corner Kitchen
STEP 1
A
B
A
suggested assembly position
Assemble Panel (A) to Panel (B) as shown using
two Screws (1) and two Barrel Nuts (3).
It may be easier to start with Panel (A) on its
back as shown above.
Remember to line up the holes in the Barrel
Nuts with the screws as explained on page 4.
3
What hardware you
will need for this step:
3 (two pieces)
B
1 (two pieces)
Item #3950
Assembled view
1
Page 5
Cook's Corner Kitchen
STEP 2
D
E
D
suggested assembly position
small holes
E
small holes
What hardware you
will need for this step:
3 (4 pieces)
1 (4 pieces)
Item #3950
Assemble panels (D) and (E) to the parts from
step 1 using four Screws (1) and four Barrel Nuts (3)
as shown above.
Make sure that panels (D) and (E) are facing the correct way,
with the two small holes as shown.
Assembled view
Page 6
Cook's Corner Kitchen
STEP 3
C
F
suggested assembly position
C
F
1
3
What hardware you
will need for this step:
3 (8 pieces)
1 (8 pieces)
Item #3950
Now assemble panels (C) and (F)
as shown using eight screws (1) and
eight barrel nuts (3).
Remember to turn the barrel nuts
as explained on page 4 so that the
screws line up with the threaded holes.
Page 7
Assembled view
Cook's Corner Kitchen
STEP 4
18
17
I
First assemble the Range Knob
(17) to Panel (H) as shown here by
screwing on the Plastic Nut (18) to
the Range Knob.
H
I
Make sure to line up the peg
with the smaller hole in the panel.
Next, insert Panels (G) and (H)
by slightly spreading the side
panels and inserting the dowels
on the panels into the holes on
the side panel and the center
panel.
G
H
Now, lining up the Panels (I)
with the slots in the sides
and center panels, slide them
down into place as shown.
side panel
Item #3950
side panel
Assembled view
Page 8
Cook's Corner Kitchen
STEP 5
Assemble Panels (J) and (K) as
shown using three Screws (1) and
three Barrel Nuts (3).
Then assemble Panels (L) and (M)
using four Screws (1) and four
Barrel Nuts (3).
1
K
J
L
3
M
What hardware you
will need for this step:
6
6 (4 pieces)
3 (7 pieces)
Attach two Latch Plates (9) using
four Screws (6) as shown above
and in the detail on the left.
1 (7 pieces)
Item #3950
small holes
9
Page 9
Assembled view
Cook's Corner Kitchen
STEP 6
1
P
7
N
Assemble Handle (P) as shown to both the
Oven Door (N) and Fridge Door (O) using two
Screws (1) and two Nuts (7) for each Handle.
Tighten using the included wrench and a
screwdriver.
Next, assemble the Hinges (11) as shown to
each door. Make sure that the "bent" side of
the Hinge is attached to the door and that it
fits in the door notch properly. Use two
Screws (4) and two Nuts (7) for each Hinge.
4
6
O
10
Assemble a Door Latch (10)
to each door as shown using
two Screws (6).
P
6
What hardware you
will need for this step:
10
bent side of
the hinge
6 (4 pieces)
7
1
Assembled view
front side
NOTE: The small
holes are only on
the back of the
door as shown
here.
7 (12 pieces)
4
1 (4 pieces)
Item #3950
4
(8 pieces)
typical Hinge
assembly
7
11
Page 10
Assembled view
back side
Cook's Corner Kitchen
STEP 7
N
O
NOTE: The (5) screws are
shorter than the (4) screws.
Make sure you use the short
screws for this assembly.
Attach the Fridge Door (O)
and the Oven Door (N) using
two Screws (5) for each
Hinge as shown. The
screws will thread directly
into the center panel.
5
What hardware you
will need for this step:
5 (8 pieces)
Item #3950
Detail view of Hinge
assembly
Page 11
Assembled view
Cook's Corner Kitchen
STEP 8
Attach two Posts (R) using two
Screws (2).
Attach the three Range Burners
(S) with a Screw (2) and a Nut
(7) for each. Use the included
wrench to tighten.
2
R
Assemble the Hot and
Cold taps (14) with two
Plastic Spacers (15) and
two Screws (8).
R
13
Then attach the Faucet
Base (13) with a Screw (8).
Next assemble three Range Knobs
(17) using the Plastic Nut (18) as
shown. The Plastic Nut screws
on to the Range Knob from
underneath the counter top.
S
14
S
S
17
Q
8
8
What hardware you
will need for this step:
15
8
2
7
18
7 (3 pieces)
8 (3 pieces)
2 (5 pieces)
Item #3950
top view showing location
of parts and their holes.
Page 12
Assembled view
Cook's Corner Kitchen
STEP 9
Attach the Counter Top assembly
as shown using six Screws (1) and
six Barrel Nuts (3).
1
Don't tighten the screws completely
until all six screws have been
installed, then continue to
tighten all of them.
3
What hardware you
will need for this step:
3 (6 pieces)
1 (6 pieces)
Item #3950
Page 13
Assembled view
Cook's Corner Kitchen
STEP 10
Assemble the Timer (19) to the
Shelf (U) using two Screws (2)
and two Nuts (7) as shown. Don't
make the screws too tight.
2
12
16
19
U
R
2
T
7
R
Then assemble the Shelf (U) to
the Posts (R) using two screws (2).
Make sure the recessed holes are
facing up. This is the top side.
Attach the Cutting Board (T) with
two Screws (2) and two Nuts (7).
Next, drop the Sink (16) in
place as shown and attach
with two Screws (6). Attach
the Faucet (12) into the Base
by pushing it directly down
until it snaps.
2
7
Detail of Timer mounting
as shown from the back
Recessed holes
are face up.
Now your Cook's Corner
Kitchen is ready for play.
6
7
What hardware you
will need for this step:
7
(4 pieces)
2 (6 pieces)
6 (2 pieces)
Item #3950
Assembled view
Page 14