+P4B533 FRONT.P65

Motherboard
P4B533
Checklist
ii
iii
Features
Safeguards
iv
v
Federal Communications Commission Statement
This device complies with FCC Rules Part 15. Operation is subject to the
following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the
graphics card is required to assure compliance with FCC regulations.
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to
operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
vi
vii
viii
ix
x
12 3
4
5
6
7
8
19
18
17
9
10
16
11
15
14
20
13
12
21
22
23
24
28
27
26
25
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
21.9cm (8.6in)
CPU_FAN
KBPWR
USBPWR_34
OVER_VOLT
USB20_12
Top:Line In
Center:Line Out
Below:Mic In
2 3
4 5
FLOPPY
0 1
DSW1
PWR_FAN
Accelerated Graphics Port (AGP)
PCI1
CHA_FAN
®
Intel I/O
Controller
Hub
(ICH4)
PCI2
AUX CD
BCS1
BCS2
IDE1
FP_LINE_IN
Super
I/O
AGP_WARN
PCI3
CLRTC
CR2032 3V
Lithium Cell
CMOS Power
FP_LO_SWL
FP_LO_SWR
PCI4
P4B533
DSW2
TRPWR
PCI5
4Mbit
Firmware
Hub
SMB
IR_CON
CHASSIS
IDE_LED
ASUS
PCISMB_SW1
PCISMB_SW2
ASIC
with
Hardware
Monitor
CMI8738 6CH
Audio Controller
C-Media
FP_AUDIO
SB_PWR
MODEM
AUDIO_SW
JEN
USBPWR_56
SPEECH
PCI6
Speech
Controller
SPDIF_C
GAME
SMARTCON
USB20_56
AFPANEL
PANEL
30.5cm (12.0in)
Intel 845E
Memory
Controller
Hub (MCH)
ATX12V
ATX Power Connector
USBPWR_12
IDE2
COM2
DDR DIMM3 (64/72 bit, 184-pin module)
PARALLEL PORT
COM1
DDR DIMM2 (64/72 bit, 184-pin module)
Socket 478
EZ_PLUG
USB20_34
DDR DIMM1 (64/72 bit, 184-pin module)
PS/2KBMS
T: Mouse
B: Keyboard
AGP_WARN
ON
Incorrect
AGP Card
OFF
Correct
AGP Card
®
SB_PWR
P4B533
P4B533 Onboard LED
ON
Standby
Power
OFF
Powered
Off
90 - 100
®
80 Pins
104 Pins
P4B533
P4B533 184-Pin DDR DIMM Sockets
®
P4B533
Keyed for 1.5v
P4B533 Accelerated Graphics Port (AGP)
DSW1
1 2 3 4 5 6
DSW2
ON
P4B533 DIP Switches
OFF
ON
ON
®
P4B533
1.Frequency Selection
2.Frequency Selection
3.Frequency Selection
4.Frequency Selection
5.Frequency Selection
6.Frequency Selection
OFF
1.Frequency Multiple
2.Frequency Multiple
3.Frequency Multiple
4.Frequency Multiple
ON
1 2 3 4
ON
DSW2
1 2 3 4 5 6
JEN
DSW1
ON
®
1 2 3 4
1 2
2 3
P4B533
P4B533
JumperFree™ Mode Setting
Jumper Free
(Default)
Jumper Mode
®
DSW2
P4B533
P4B533 CPU Frequency
Multiple Selection
ON
ON
ON
ON
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
8.0x
10.0x
11.0x
12.0x
ON
ON
ON
ON
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
13.0x
14.0x
15.0x
16.0x
ON
ON
ON
ON
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
17.0x
18.0x
19.0x
20.0x
ON
ON
ON
ON
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
21.0x
22.0x
23.0x
24.0x
CPU 141MHz
AGP 70MHz
PCI
35MHz
P4B533 CPU
External Frequency Selection
145MHz
72MHz
36MHz
ON
1 2 3 4 5 6
1 2 3 4 5 6
1 2 3 4 5 6
166MHz
66MHz
33MHz
133MHz
66MHz
33MHz
ON
1 2 3 4 5 6
ON
109MHz
72MHz
36MHz
ON
1 2 3 4 5 6
ON
105MHz
70MHz
35MHz
1 2 3 4 5 6
ON
P4B533
1 2 3 4 5 6
®
CPU 100MHz
AGP 66MHz
PCI
33MHz
ON
1 2 3 4 5 6
ON
DSW1
200MHz
66MHz
33MHz
KBPWR
3
2
2
1
®
+5V
(Default)
+5VSB
P4B533
P4B533 Keyboard Power Setting
OVER_VOLT
2
1
®
Disable
(Default)
P4B533
P4B533 OVER_VOLT Setting
3
2
Enable
USBPWR_34
3
2
2
1
+5V
(Default)
+5VSB
USBPWR_12
2 3
1 2
+5VSB
®
+5V
(Default)
USBPWR_56
P4B533
1 2
P4B533 USB Device Wake Up
+5V
(Default)
2 3
+5VSB
SPEECH
2 3
®
1 2
P4B533
LINEOUT
(Default)
BUZZER
P4B533 Speaker Selector
®
PCISMB_SW1
PCISMB_SW2
P4B533
P4B533 PCISMB Setting
1 2
Disable
(Default)
2 3
Enable
BLOL
FLOL
BLOR
FLOR
®
FP_LO_SWL
P4B533
FP_LO_SWR
P4B533 Internal Line Out Connectors
®
BCS1
BCS2
1 2
2 3
P4B533
P4B533 Bass Center Setting
(CENTER/BASS)
(Default)
(BASS/CENTER)
AUDIO_SW
®
1 2
P4B533
2 3
Enable
(Default)
Disable
P4B533 Audio Setting
®
Intel I/O
Controller
Hub
(ICH4)
P4B533
CLRTC
Short Jumper
to Clear CMOS
P4B533 Clear RTC RAM
®
TIP: If the case-mounted LED does not
light, try reversing the 2-pin plug.
IDE_LED
P4B533
P4B533 HD Activity LED
FLOPPY
PIN 1
®
NOTE: Orient the red markings on
the floppy ribbon cable to PIN 1.
P4B533
P4B533 Floppy Disk Drive Connector
P4B533 IDE Connectors
PIN 1
PRI_IDE Connector
P4B533
SEC_IDE Connector
®
PIN 1
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
Chassis Signal
GND
P4B533
+5VSB_MB
®
CHASSIS
P4B533 Chassis Intrusion Connector
®
SMB
Ground
SMBDATA
+3V
P4B533 SMBus Connector
1
FLOATING
SMBCLK
P4B533
®
P4B533
ATXPWR
EZ_PLUG
Pin 1
+5V
GND
GND
+12V
+12.0VDC
+5VSB
PWR_OK
COM
+5.0VDC
COM
+5.0VDC
COM
+3.3VDC
+3.3VDC
+5.0VDC
+5.0VDC
-5.0VDC
COM
COM
COM
PS_ON#
COM
-12.0VDC
+3.3VDC
ATX12V
+12V DC GND
+12V DC GND
P4B533 ATX & Auxiliary Power Connectors
GND
+12V
Rotation
®
PWRFAN
GND
+12V
Rotation
CPU_FAN
CHA_FAN
GND
+12V
Rotation
P4B533
P4B533 12-Volt Fan Connectors
®
TRPWR
P4B533
Ground
TRPWR
P4B533 Power Supply Thermal Connector
1
P4B533 Smartcard
VCC
NC
SCRFET#
SCRCLK
NC
GND
NC
NC
NC
SCRREST
NC
SCRUI
SCRRES#
®
P4B533
USB20_56
6
5
1
P4B533 USB 2.0 Header
NC
GND
LDP5
LDM5
USB+5V
10
SMARTCON
P4B533
GND
LDP6
LDM6
USB+5V
®
Front View
Back View
+5V
(NC)
IRRX
GND
IRTX
IR
®
1
+5V
(NC)
IRTX
GND
P4B533
IRRX
P4B533 Infrared Module Connector
8
+5V
J1B2
J1CY
GND
GND
J1CX
J1B1
+5V
®
GAME
1
P4B533
P4B533 Game Connector
9
MIDI_IN
J2B2
J2CY
MIDI_OUT
J2CX
J2B1
+5V
16
AUX (White) CD(Black)
®
Left Audio Channel
Ground
Ground
Right Audio Channel
P4B533
MODEM
P4B533 Internal Audio Connectors
®
BLINE_IN_R
LINE_IN_R
AGND
BLINE_LIN_L
ALINE_LIN_L
FP_LINE_IN
P4B533
P4B533 LINE_IN Connector
Modem-Out
Ground
Ground
Modem-In
+5 V
NC
GND
NC
CIRRX
+5VSB
CHASSIS#
EXTSMI#
+5V
MLEDPCIRST#
BATT
NC
IRRX
GND
IRTX
SMBDATA
+3VSB
SMBCLK
NC
NC
NC
NC
AFPANEL
Connect to AFPANEL Connector
IRRX
GND
IRTX
®
+5 V
Connect to iPanel
SIR
CIR
NC
GND
NC
CIRRX
+5VSB
P4B533
IR_CON
P4B533 iPanel Connector
SPDIF_C
SPDIF_OUT
GND
®
+5V
GND
P4B533
P4B533 Digital Audio Connector
SPDIF_IN
1
FP_AUDIO
Line out_L
NC
Line out_R
MICPWR
MIC2
®
BLINE_OUT_L
P4B533
BLINE_OUT_R
+5VA
AGND
P4B533 Front Panel Audio Connector
P4B533
Message LED
SMI Lead
P4B533 System Panel Connectors
Reset
Ground
®
+5 V
MLED
ExtSMI#
Ground
PWRBIN
Ground
+5 V
PLED
Keylock
Ground
Power LED
Speaker
Connector
+5V
Ground
Ground
Speaker
Keyboard Lock
Reset SW
ATX Power
Switch*
* Requires an ATX power supply.
ASUS EZ Flash V1.00
Copyright (C) 2002, ASUSTeK COMPUTER INC.
[Onboard BIOS Information]
BIOS Version
: ASUS P4B533 ACPI BIOS Revision 1002
BIOS Model
: P4B533
BIOS Built Date : 04/16/02
Please Enter File Name for NEW BIOS: _
*Note: EZ Flash will copy file from A:\, Press [ESC] to reboot
[BIOS Information in File]
BIOS Version: P4B533 Boot Block
WARNING! Continue to update the BIOS (Y/N)? _
Flash Memory:
SST 49LF004
1. Update Main BIOS area
2. Update Boot Block area
(Y/N)? _
(Y/N)? _
1.750V, 1.775V, 1.800V,
1.825V, 1.850V
1.750V, 1.775V, 1.800V,
1.825V, 1.850V, 1.875V,
1.900V, 1.925V, 1.950V
1.500V, 1.525V, 1.550V,
1.575V, 1.600V, 1.625V,
1.650V, 1.675V, 1.700V
1.500V, 1.525V, 1.550V,
1.575V, 1.600V, 1.625V,
1,650V, 1.675V, 1.700V,
1.725V, 1.750V, 1.775V,
1.800V, 1.825V, 1.850V,
1.875V, 1.900V, 1.925V,
1.950V
TV
Box