Tots in Mind - Safe Beginnings

CCTConvCribInstructions_6.2010
8/5/10
3:30 PM
Page 1
Patent Pending
Tots in Mind
Helping to keep children safe… from generation to generation!
Assembly Instructions for
Cozy Crib Tent for Convertible Cribs
Ages 0-36 Months – To be used by one child at a time.
WARNING!
This product must be assembled by an adult. Read these assembly instructions and
warnings completely before you begin.This will make assembly and use easier, quicker, and safer.
Keep Cozy Crib Tent II away from flames, cigarettes and all heat sources.
WARNING ! If your Cozy Crib Tent
Top Rod Sleeves
for Convertible Cribs does not fit the
crib, do not use it. Return to place of
purchase for a refund.
(Top Rod Position)
Rear Straps
(5, located on back
of tent, not shown)
FRONT VIEW (ZIPPER SIDE)
Horizontal Strap
Corner Rod Pocket
Railing Wrap
Horizontal Strap
Railing Wrap Straps (5)
End Panel
Vertical Strap
Vertical Strap
MATERIALS LIST:
4 Rod Sections with metal fittings
2 Rod Sections without metal fittings
1 Poly bagged mesh Cozy Crib Tent for Convertible Cribs
For information on how to attach a Cozy Crib
Tent for Convertible Cribs, visit TotsInMind.com.
The Cozy Crib Tent for Convertible Cribs
WILL NOT FIT if:
• The back or front of the crib is solid (without slats)
• The “slope” (height difference between where the side meets
the front & where the side meets the back) is greater than 6 1/2"
• The crib has any built in furniture (such as a changing table
or shelving)
• The crib is greater than 56" long
(outside edge to outside edge)
x 31" wide (from where the
61/2" slope
back rail meets the side rail to
the outside edge of the front rail.)
• The front railing is greater than
Not greater than 31"
20 1/2" around.
Diagram 1
*If using a bumper pad, place on OUTSIDE
of netting (between crib slats and net).
Zipper Pocket
STEP 1: Assemble rod sections
Assemble the two top rods, each
made up of 3 sections (2 with
metal fittings, 1 without) creating
two completed top rod assemblies
(diagram 1).
ing
itt
F
al
et
M
WARNING! Could Cause Injury.
Keep rods pointed away from face and pointed in
safe direction.Top rod tension could cause a
spring-back action during assembly!
Diagram 3
Push with Palm
Button
Hole Tab
STEP 3: Push rod
assemblies into
bottom of rod sleeves
Completely
covered rod
tucked properly
into reinforced
button hole tab.
Once both completed top rod assemblies are in their respective
sleeves (making sure each rod assembly is all the way into its
reinforced rod sleeve at back end), use a push-pull method to
completely cover both top rod assemblies. Cover exposed end
of rod assemblies by grasping material in one hand and pushing
rod assembly in with palm of other hand until rod is completely
covered and tucks back into its reinforced button hole tab
forming dome of tent (diagram 3).
Diagram 4
Covered rod tucked
into reinforced
button hole tab.
Diagram 2
Button
Hole
Button
Hole Tab
Front View
(Zipper Side)
STEP 2: Insert the two completed top rod assemblies
Locate the 2 button holes at front (zipper side) end of each top
rod sleeve. Insert one completed rod assembly into each of the
2 button holes (diagram 2) making sure each rod assembly is
all the way into its reinforced rod sleeve at back end of unit,
leaving both rod assemblies slightly sticking out of button hole
until Step 3.
The poly bag can suffocate a child. Promptly dispose of
the poly bag where it cannot be reached by children.
Corner
Rod Pocket
STEP 4: Place top rod assembly ends into pockets
Place the four rod assembly ends into their respective pockets
located in each corner by slightly bowing the end of each rod with
one hand and grasping the pointed tip end of border with other
hand, so it will gently slip into pocket (diagram 4). (DO NOT
attempt to stretch pocket over rod ends. Gently pull rod
pocket TIP and bow rod into pocket). The inserted rod end in its
pocket then sits INSIDE THE FOLD of the vertical strap material.
WARNING!
Total structure strength is only achieved
when rod ends are inserted into corner rod pockets.
Please see reverse side for further directions!
CCTConvCribInstructions_6.2010
8/5/10
3:30 PM
Page 2
STEP 5: Placing the Cozy Crib Tent for
Convertible Cribs on crib
A. Remove mattress from crib.
B. Crib frame MUST be set to the LOWEST setting.
C. If you are using a bumper pad, attach it to crib slats
BEFORE placing tent on crib (bumper pad placement is
BETWEEN crib slats and net).
D. Place assembled tent on crib (making sure zipper opening
faces front) with Crib Tent dome portion resting on top of
crib side rails allowing inside surround net to hang freely
inside crib (bottom net rests on top of mattress frame).
E. Adjust the tent so that it is evenly set on the crib frame
(check each corner).
WARNING!
DO NOT add additional strings, straps,
hook & loop, etc. to attach tent to crib!
Diagram 6A
Vertical
Strap
Diagram 8
Diagram 8A
Headboard & footboard
STEP 8: Securing horizontal end panels
Secure Horizontal End Panel Straps making sure to feed one
strap through the front and one strap through the rear of crib,
wrap around crib posts over vertical strap (diagram 8A), weave
into the first slot and out the second slot on the side of the crib
so that they connect crossing over the end panel laying flat
against the crib slats (diagram 8).
Diagram 6B
WARNING!
NEVER leave child unattended unless tent is securely
attached to crib and completely zipped.Tent should be
zipped when not in use. Failure to do so may cause injury.
Diagram 9
STEP 6: Securing tent to crib
A. Feed the 5 railing wrap straps, beginning at the center and
working outward, between the tent netting and crib frame.
Feed the straps between the slats on the front of the crib,
and through the loops on the underside of the railing wrap.
Pull straps in a downward motion to tighten, then pull the
strap up and around the backside of the front railing to
attach the strap to itself.
B. Feed five rear straps through the slats and attach each to
itself by wrapping it around the crib slats (diagram 6B).
NOTE: If there is excess strap after it is wrapped around the
crib slat, continue to wrap the rough end around itself near
the seam.
Diagram 7
STEP 9: Prepare crib and tent for use
Unzip the front panel, insert mattress into the Cozy Crib Tent
for Convertible Cribs so that it lays flat on bottom of crib, and
zip front panel (diagram 9). Always check to make sure all
straps are securely bonded and pulled as tautly as possible.
Also check that the zipper pull is completely tucked inside the
zipper pocket after placing your child inside the tent.
Collapses for easy storage or travel:
1. Detach unit from crib
2. Squeeze top rods together so unit flattens into a half circle
3. Tuck excess material (inside surround net) into flattened dome
4. Keep unit closed by wrapping the closest end hook and look
strap around both rod ends then secure strap to lock.
(subject to change for product improvement without notice.)
STEP 7: Secure top & bottom vertical straps
Secure top & bottom vertical straps. Make sure to feed bottom
straps through the corners of the mattress frame, out and under
the side of the crib. Then pull straps tightly and attach them
securely (top to bottom, diagram 7).
Use according to instructions —
to be used with (not in place of) parental supervision.
Failure to do so may cause injury.
IMPORTANT!
PLEASE NOTE THE FOLLOWING:
• When zipping the zipper, always make sure the zipper
pull is inserted into its safety pocket.
• When washing or storing, make sure all hook and loops
are properly closed so lint or dirt will not hinder bonding.
• Check all hook and loop fasteners each and every time
your Cozy Crib Tent for Convertible Cribs is in use.
• If your Cozy Crib Tent for Convertible Cribs does not fit
the crib, DO NOT USE! Return to place of purchase.
• NOT to be used as punishment.
• Please save these instructions for future reference.
LIMITED WARRANTY
This warranty is extended only to the original purchaser. A purchase receipt or other proof of date of original purchase will be
required before warranty performance is rendered.
This warranty only covers failures due to manufacturing defects
which occur during normal use. It does not cover damage which
results from misuse, abuse, mishandling, alteration, or improper
assembly.
There are no other express oral or written warranties with
respect to this product, and all warranties implied by law, including any warranties of merchantability or fitness for a
particular purpose, are limited in their duration to the 60-day warranty period. (Some states do not allow limitation on how long an
implied warranty lasts, so the above limitation may
not apply to you.)
This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
Cozy Crib Tent for Convertible Cribs is warranted against
defects in materials and workmanship for a period of 60 days
after the original date of consumer purchase. If the Cozy Crib
Tent for Convertible Cribs should become defective within the
warranty period, we will replace it free of charge. Contact Tots in
Mind at: [email protected]
For your convenience, please visit or website for additional products, additional information and the closest retail location near you.
www.TotsInMind.com
email: [email protected]