A-dec 371-200 Dental Light on an A

A-dec 371-200 Dental Light on
an A-dec 200 Dental Chair
INSTALLATION GUIDE
Install the Dental Light
4
1. Insert and fully seat the bearing in the support
center post.
2. Place the trim cover on top of the bearing.
3
2
4. Insert the dental light post.
5. Route the wiring out of the post into the support
center.
1
5
86.0314.00 Rev D
3. Route wiring down into the support center post.
A-dec 371-200 Dental Light on an A-dec 200 Dental Chair Installation Guide
Connect the Dental Light
Task 1.
Prepare the dental light cable in the support center.
If the dental light cable has a green wire with a WAGO connector already attached, go to Task 2 on
the next page.
NOTE
back the sheath 80 mm (3") then strip
1 Strip
back the green wire 7 mm (1/4").
a WAGO connector to the end of the
2 Attach
green wire.
To
Floor Box
2
86.0314.00 Rev D
A-dec 371-200 Dental Light on an A-dec 200 Dental Chair Installation Guide
Task 2.
Connect the wires from the light to the WAGO connectors with the same color wires.
To Dental Light
To Floor Box
86.0314.00 Rev D
3
A-dec 371-200 Dental Light on an A-dec 200 Dental Chair Installation Guide
Connect the Floor Box Utilities
Install the Dental Light Relay Circuit Board
Recommended Tool
Phillips head screwdriver
Secure the dental light relay circuit board with the screw from the top of the power supply.
4
86.0314.00 Rev D
A-dec 371-200 Dental Light on an A-dec 200 Dental Chair Installation Guide
Connect the Dental Light Jumper Cable and Data Line
Get the dental light jumper cable and data line from the kit and make the following connections.
2 Connect the white plug.
3 Connect the data line.
1 Connect the red plug.
86.0314.00 Rev D
5
A-dec 371-200 Dental Light on an A-dec 200 Dental Chair Installation Guide
Connect the Dental Light Cable
Follow the procedure according to the type of dental light cable used.
The circuit board is static sensitive. ESD precautions are required. The circuit board should be
installed by an electrician or qualified service personnel.
CAUTION
Light Cables with a Green Wire Attached
If the end of the light cable includes a green wire connected to the red connector, complete the following
procedure:
Connector with Green Wire Attached
1 Connect the wires to their positions on the relay board.
BLK
VIO
2
Connect the light cable (from kit).
WHT
BLK/WHT
6
86.0314.00 Rev D
A-dec 371-200 Dental Light on an A-dec 200 Dental Chair Installation Guide
Light Cables without a Green Wire Attached
If the end of the light cable does not have a connector or does not have a green wire connected to the red
connector, complete the following procedures:
Cable with No Connector
Cable without a Green Wire Attached to the Connector
Task 1.
1 Snip off the wires at the end of the sheath.
2 Strip back the sheath 80 mm (3").
3 Strip back the wires 7 mm (1/4").
86.0314.00 Rev D
7
A-dec 371-200 Dental Light on an A-dec 200 Dental Chair Installation Guide
Task 2.
the dental light wires to the adaptor cable with WAGO connectors.
1 Attach
Match the wire to the WAGO connector with the same color wire.
BLK
BLK
VIO
VIO
BLUE
GRN
2 Connect the adaptor cables.
WHT
BLK/WHT
the wires from the second adaptor
3 Connect
cable to their positions on the relay board.
8
86.0314.00 Rev D
A-dec 371-200 Dental Light on an A-dec 200 Dental Chair Installation Guide
Install the Dental Light Flexarm Rotation Stop Pins
the
1 Lift
trim ring.
the
2 Insert
stop pin.
Actual Size of Pin
86.0314.00 Rev D
9
A-dec 371-200 Dental Light on an A-dec 200 Dental Chair Installation Guide
Adjust the Dental Light Flexarm Counterbalance (if needed)
Recommended Tools
• Phillips head screwdriver
• 1/2" combination wrench
NOTE An optional travel stop limit kit (p/n 90.1044.00) can be installed to limit the upward and
downward motion of the flexarm.
1 Remove the two screws and end cap.
2 Remove the screw and end cap.
3 Remove the cover.
the light drifts up, turn the nut
4 Ifcounterclockwise.
If the light drifts down, turn the
nut clockwise.
the cover onto the
5 Set
flexarm to test the drift.
10
86.0314.00 Rev D
A-dec 371-200 Dental Light on an A-dec 200 Dental Chair Installation Guide
Adjust the Dental Light Rotation Tension (if needed)
Adjust the Dental Light Horizontal Rotation
Recommended Tool
5/32" hex key
To increase tension, turn the screw clockwise.
To decrease tension, turn the screw counterclockwise.
Adjust the Dental Light Vertical Rotation
Recommended Tool
3/16" hex key
To increase tension, turn the screw clockwise.
To decrease tension, turn the screw counterclockwise.
86.0314.00 Rev D
11
A-dec 371-200 Dental Light on an A-dec 200 Dental Chair Installation Guide
Adjust the Dental Light Focus (if needed)
The A-dec 371-200 does not have a focus adjustment.
Touchpad Settings
For dental light touchpad settings, see the “Touchpad Settings” section of the A-dec 200 Installation Guide
(p/n 86.0004.00).
Regulatory Information
Regulatory information is provided with A-dec equipment as mandated by agency requirements. This
information is delivered in the equipment’s Instructions for Use or the separate Regulatory Information and
Specifications document. If you need this information, please go to the Document Library at www.a-dec.com.
A-dec Headquarters
2601 Crestview Drive
Newberg, OR 97132 USA
Tel: 1.800.547.1883 Within USA/Canada
Tel: 1.503.538.7478 Outside USA/Canada
Fax: 1.503.538.0276
www.a-dec.com / www.a-dec.biz
A-dec Inc. makes no warranty of any kind with regard to
the content in this document including, but not limited
to, the implied warranties of merchantability and fitness
for a particular purpose.
ÍvÈ.Ç#.È.00wÎ
86.0314.00 Rev D
Copyright 2012 A-dec Inc.
All rights reserved.
IGgrph4