1 EC-TYPE EXAMINATION CERTIFICATE

1
2
EC-TYPE EXAMINATION CERTIFICATE
Equipment or Protective systems intended for use in Potentially
Explosive Atmospheres - Directive 94/9/EC
3
EC-Type Examination Certificate No:
FM11ATEX0019X
4
Equipment or protective system:
(Type Reference and Name)
®
®
1101 Series BULLET WirelessHART Adaptor
5
Name of Applicant:
MACTek Corporation
6
Address of Applicant:
7380 Stoneham Road
Gates Mills, Ohio 44040 USA
7
This equipment or protective system and any acceptable variation thereto is specified in the schedule to this
certificate and documents therein referred to.
8
FM Approvals Ltd, notified body number 1725 in accordance with Article 9 of Directive 94/9/EC of 23 March
1994, certifies that this equipment has been found to comply with the Essential Health and Safety Requirements
relating to the design and construction of equipment intended for use in potentially explosive atmospheres given
in Annex II to the Directive.
The examination and test results are recorded in confidential report number:
3040786EC dated 23 December 2011
9
Compliance with the Essential Health and Safety Requirements, with the exception of those identified in item 15
of the schedule to this certificate, has been assessed by compliance with the following documents:
10
11
EN 60079-0:2012+A11:2013, EN 60079-11:2012, EN 60079-26:2007, EN 60079-31:2014, and
EN 60529:+A2 2013
If the sign ‘X’ is placed after the certificate number, it indicates that the equipment is subject to special
conditions for safe use specified in the schedule to this certificate.
This EC-Type Examination certificate relates only to the design, examination and tests of the specified
equipment or protective system in accordance to the directive 94/9/EC. Further requirements of the Directive
apply to the manufacturing process and supply of this equipment or protective system. These are not covered by
this certificate.
Mick Gower
cn=Mick Gower, o=FM Approvals, ou,
[email protected],
c=GB
2014.09.22 09:18:34 +01'00'
Mick Gower
Certification Manager, FM Approvals Ltd.
Issue date: 22nd September 2012
THIS CERTIFICATE MAY ONLY BE REPRODUCED IN ITS ENTIRETY AND WITHOUT CHANGE
FM Approvals Ltd. 1 Windsor Dials, Windsor, Berkshire, UK. SL4 1RS
T: +44 (0) 1753 750 000 F: +44 (0) 1753 868 700 E-mail: [email protected] www.fmapprovals.com
F ATEX 020 (May/12)
Page 1 of 3
SCHEDULE
to EC-Type Examination Certificate No. FM11ATEX0019X
12
The marking of the equipment or protective system shall include:
110101-b0d0 BULLET® WirelessHART® Adaptor.
II 1 G Ex ia IIC T* ; IP68
*T5 for Ta = -40°C to +85°C;
T6 for Ta = -40°C to +75°C
II 1 D Ex iaD 20 IP68 T95C; Ta = -40°C to +85°C
®
®
110103-b0d0 BULLET WirelessHART Adaptor.
II 1 G Ex ia IIC T* ; IP68
*T5 for Ta = -40°C to +85°C;
T6 for Ta = -40°C to +75°C
II 1 D Ex iaD 20 IP68 T95C; Ta = -40°C to +85°C
13
Description of Equipment or Protective System:
The Model 1101 Series BULLET® WirelessHART® Adaptor is intended to be installed into a
4-20mA current loop with electrical equipment using HART communications. The HART electrical signals
are converted and delivered as wireless transmission.
®
®
The electronics of the Model 1101 Series BULLET WirelessHART Adaptor, except for the antenna board,
are completely encapsulated and located inside of a painted metallic cylindrical housing with a polymeric
dome cover. The antenna board protrudes through the encapsulation and is located under the polymeric
dome cover.
The cylindrical housing is approximately 2.4” in diameter by 4.5” in length. The bottom side of the housing is
sealed with potting material where pig-tail wires protrude through the potting for installation. The housing
also contains threads for installing into a final enclosure. The Model 1101 Series BULLET® WirelessHART®
Adaptor’s enclosure meets Type of protection IP68 and NEMA Type 6P.
The nominal operation of the Model 1101 Series BULLET® WirelessHART® Adaptor is 7-32V and 425mA. It is intended to be operated in ambient up to 85°C.
The Model code is as follows:
110101-b0d0 BULLET® WirelessHART® Adaptor.
Energy Limitation Parameters:
Ui = 30V, Ii = 120mA, Pi = 0.9W, Ci = 0, Li = 595.96μH.
b = Multidrop devices: 0, 2, 8, or P.
d = 0 for MACTek or another single character to represent an alternate supplier/re-seller,.
110103-b0d0 BULLET® WirelessHART® Adaptor.
Energy Limitation Parameters:
Ui = 30V, Ii = 120mA, Pi = 0.9W, Ci = 0, Li = 595.96μH.
b = Multidrop devices: 0, 2, 8, or P.
d = 0 for MACTek or another single character to represent an alternate supplier/re-seller,
THIS CERTIFICATE MAY ONLY BE REPRODUCED IN ITS ENTIRETY AND WITHOUT CHANGE
FM Approvals Ltd. 1 Windsor Dials, Windsor, Berkshire, UK. SL4 1RS
T: +44 (0) 1753 750 000 F: +44 (0) 1753 868 700 E-mail: [email protected] www.fmapprovals.com
F ATEX 020 (May/12)
Page 2 of 3
SCHEDULE
to EC-Type Examination Certificate No. FM11ATEX0019X
14
Specific Conditions of Use:
1. For Zone 0 installation only, the equipment contains aluminum and is considered to constitute a
potential risk of ignition by impact or friction. Care must be taken into account during installation and use
to prevent impact and friction.
2. Using the box provided on the nameplate, the user shall permanently mark the type of protection
chosen for the specific installation. Once the type of protection has been marked it shall not be changed.
15
Essential Health and Safety Requirements:
The relevant EHSRs that have not been addressed by the standards listed in this certificate have been identified
and assessed in the confidential report identified in item 8.
16
Test and Assessment Procedure and Conditions:
This EC-Type Examination Certificate is the result of testing of a sample of the product submitted, in
accordance with the provisions of the relevant specific standard(s), and assessment of supporting
documentation. It does not imply an assessment of the whole production.
Whilst this certificate may be used in support of a manufacturer’s claim for CE Marking, FM Approvals Ltd
accepts no responsibility for the compliance of the equipment against all applicable Directives in all
applications.
This Certificate has been issued in accordance with FM Approvals Ltd’s ATEX Certification Scheme.
17
Schedule Drawings
A list of the significant parts of the technical documentation is annexed to this certificate and a copy has
been kept by the Notified Body.
18
Certificate History
Details of the supplements to this certificate are described below:
Date
Description
13 January 2012
Original Issue.
28 June 2012
18th December 2012
22nd September 2014
Supplement 1:
Report Reference: 3040786rev120504 dated 12th June 2012.
Change to description of equipment, to add label marking variant S to denote a
Siemens marked product.
Supplement 2:
Report Reference: 3040786rev121029 dated 5th December 2012.
Change to description of equipment. Added the model 110103 variant.
Supplement 3:
Report Reference: 3050586 dated 17th September 2014
Description of the Change: Updating EN 60079-0, EN 60079-11, EN 60079-31, and
EN 60529 to the latest editions. Adding a new encapsulant. Corrected nameplates.
THIS CERTIFICATE MAY ONLY BE REPRODUCED IN ITS ENTIRETY AND WITHOUT CHANGE
FM Approvals Ltd. 1 Windsor Dials, Windsor, Berkshire, UK. SL4 1RS
T: +44 (0) 1753 750 000 F: +44 (0) 1753 868 700 E-mail: [email protected] www.fmapprovals.com
F ATEX 020 (May/12)
Page 3 of 3
Blueprint Report
MACTek Corporation (116305)
Class No
3610
Original Project I.D.
Certificate I.D.
3040786
FM11ATEX0019X
Drawing No.
Revision Level
Drawing Title
Last Report
Electronic Drawing
AF11010200
BA
ENCLOSURE ASSEMBLY - HAZARDOUS LOCATION
3050586
Yes (pdf)
AF1101021B
BA
ENCLOSURE ASSEMBLY BOM - HAZARDOUS LOCATION
3050586
Yes (pdf)
AP11010200
BA
PCB FINAL ASSEMBLY - HAZARDOUS LOCATION
3050586
Yes (pdf)
AP1101021B
BA
PCB ASSEMBLY BOM - INTRINSICALLY SAFE
3050586
Yes (pdf)
AT1101010C
BA
BULLET WIRELESSHART CONTROL DRAWING
10/29/12
Yes (pdf)
AT1101030C
AA
SITRANS AW210 Wireless Adapter Control Drawing
3047564
Yes (pdf)
DE11010100
BA
CERTIFICATION DRAWING ENCLOSURE ASSEMBLY
3050586
Yes (pdf)
DE11010200
AC
CERTIFICATION DRAWING OVERMOLD DOME ASSEMBLY
3040786
Yes (pdf)
DL11010200
CA
NAMEPLATE INTRINSICALLY SAFE MODEL 110101
3050586
Yes (pdf)
DL11010400
BA
NAMEPLATE INTRINSICALLY SAFE/XP MODEL 110103
3050586
Yes (pdf)
DL11010900
BA
Siemens - 7MP3111-1AB00-0AA0 Label Drawing
3047564
Yes (pdf)
DL11011000
BA
Siemens - 7MP3111-2AB00-0AA0 Label Drawing
3047564
Yes (pdf)
DM1101008
AA
MACTek-SIEMENS Private Label-Trade Agent Agreement 3047564
3047564
Yes (pdf)
DM1101010U
DA
MACTek Corporation BULLET WirelessHART Adapter Model 1101 Series User Manual
10/29/12
Yes (pdf)
DM1101020U
BB
Siemens - 7MP3111 SITRANS AW210 Instruction Manual
3047564
Yes (pdf)
ES-769
D
ES-769.pdf
3047209
Yes (pdf)
PW11010200
AH
PCB FABRICATION PW11010200 TOP PATCH BOARD
3040786
Yes (pdf)
PW11010230
AH
ANTENNA TOP PATCH PCB LAYOUT
3040786
Yes (pdf)
PW11010300
AB
PCB FABRICATION PW11010300 BOTTOM GROUND
3040786
Yes (pdf)
PW11010330
AB
ANTENNA BOTTOM GROUND PCB LAYOUT
3040786
Yes (pdf)
PW11010400
AE
PCB FABRICATION PW11010400 WIRELESS ADAPTER
3040786
Yes (pdf)
PW11010410
AC
WIRELESSHART ADAPTER INTRINSICALLY SAFE SCHEMATIC
3040786
Yes (pdf)
PW11010430
AE
MAIN BOARD PCB LAYOUT
3040786
Yes (pdf)
22/09/2014
Page 1 of 1