Test result - Funkamateur

Transcription

ISO/IEC17025 Accredited Lab.
Report No:
File reference No:
EMC1103180-01
2011-03-31
Applicant:
FUJIAN NAN’AN BAOFENG ELECTRONICS CO., LTD.
Product:
Two Way Radio
Brand Name:
BAOFENG
Model No:
UV-3R
Test Standards:
ETSI EN300 086-1 V1.3.1 (2008-09)
ETSI EN300 086-2 V1.2.1 (2008-09)
Test result:
The EMC testing has been performed on the submitted
samples and found in compliance with council EMC Directive
2004/108/EC and R & TTE Directive 1999/5/EC
Approved By
Jack Chung
EMC Manager
Dated:
March 31, 2011
Results appearing herein relate only to the sample tested
The technical reports is issued errors and omissions exempt and is subject to
withdrawal at
TIMEWAY TECHNOLOGY DEVELOPMENT LIMITED (HONG KONG)
Rm. 1803, King Centre, No.23 Dundas Street, Mongkok, Kln. HONG KONG
Tel (852)2626 1885
Fax (852)3012 1422
Report No: 1103180-01
Date: 2011-03-31
Page 2 of 67
TEST REPORT
Special Statement：
The testing quality ability of our laboratory meet with "Quality Law of People's Republic
of China" Clause 19.
The testing quality system of our laboratory meets with ISO/IEC-17025 requirements,
which is approved by CNAL. This approval result is accepted by MRA of APLAC.
Our test facility is recognized, certified, or accredited by the following organizations:
CNAL-LAB Code: L2292
The EMC Laboratory has been assessed and in compliance with CNAL/AC01:2002
accreditation criteria for testing Laboratories (identical to ISO/IEC 17025:1999 General
Requirements) for the Competence of testing Laboratories.
FCC-Registration No.: 899988
The EMC Laboratory has been registered and fully described in a report filed with the
(FCC) Federal Communications commission. The acceptance letter from the FCC is maintained
in our files. Registration No.:899988.
IC- Registration No.: IC5205A-02
The EMC Laboratory has been registered and fully described in a report filed with the (IC)
Industry Canada. The acceptance letter from the IC is maintained in our files. Registration No.:
IC 5205A-02.
The report refers only to the sample tested and does not apply to the bulk.
This report is issued in confidence to the client and it will be strictly treated as such by the Hong Kong Timeway Technology Development Limited.
It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however,
show or send it or a certified copy there of prepared by the Hong Kong Timeway Technology Development Limited to his customer. Supplier or
others persons directly concerned. Hong Kong Timeway Technology Development Limited will not, without the consent of the client enter into any
discussion of correspondence with any third party concerning the contents of the report.
In the event of the improper use of the report. The Hong Kong Timeway Technology Development Limited reserves the rights to withdraw it and to
adopt any other remedies which may be appropriate.
Report No: 1103180-01
Date: 2011-03-31
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
2.12
2.13
2.14
2.15
2.16
2.17
3.0
4.0
5.0
6.0
Page 3 of 67
TEST REPORT
Test Report Conclusion
Content
General Details ……………………..…………………………..……………………………..…
Notes…………………………………………………………..………………….………………
Test Laboratory………………………………………………………….……………….……….
Details of Applicant……………………………………………………………..………….…….
4
4
4
4
Application Details………………………..……………………………………..………………..
Test Item…………………………….…………………………………..…….…………………..
Test Standards……………………………………………………………………………………..
Test Engineer……………………..……………………………………………………………….
Technical Test…………………………………………………………….………………………
Summary of Test Result…………………………………………………………………………..
Test Report………………………………………………………….….……….…………………
Frequency Error…………………………………………………………………………………..
Carrier Power (Conducted)……………………………………………………………………….
Effective Radiation Power (Field Strength)………………………………………………………
Frequency Deviation………………………………………………………………………………
Adjacent Channel Power…………………………………………………………………………
Spurious Emission………………………………………………………………………………..
Intermodulation Attenuation………………………………………………………………………
Receiver Parameters
Maximum Usable Sensitivity (Conducted)…………………………….…………………………
Maximum Usable Sensitivity (Field Strength)……………………………………………………
Co-Channel Selectivity……………………………………………………………………………
Adjacent Channel Selectivity……………………………………………………………………..
Spurious Response Rejection……………………………………………………………………..
Intermodulation Response Rejection……………………………………………………………..
Block Or Desensitization………………………………………………………………………….
Spurious Radiation………………………………………………………………………………..
CE Label……………………………………………………………………………….…………
Photograph-Test Set up……………………………………………………..…………………..
Photograph-EUT…………………………………………………………………………………
Test Equipments…………………………………………………………………………………
4
4
5
5
6
6
6
7
13
20
20
27
36
42
43
43
45
46
48
50
51
53
54
58
59
60
66
Report No: 1103180-01
Date: 2011-03-31
Page 4 of 67
TEST REPORT
1. General Information
1.1 Notes
The test results of this report relate exclusively to the test item specified in 1.5. The TIMEWAY Lab does not
assume Responsibility for any conclusions and generalizations drawn from the test results with regard to other
specimens or samples of the type of the equipment represented by the test item. The test report may only be
reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written
approval of the TIMEWAY Lab.
1.2 Testing Laboratory
SHENZHEN TIMEWAY TECHNOLOGY CONSULTING CO LTD
East 5/Block 4, Anhua Industrial Zone, No.8,Tairan Rd. CheGongMiao, FuTian District, Shenzhen, CHINA
Tel: +86 755 83448688
Fax :+86 755 83442996
Internet: www.timewaytech.com
Site on File With the Federal Communications and Commission – United States
Registration Number: 899988
For 3m & 10 m OATS
Site Listed with Industry Canada of Ottawa, Canada
Registration Number: IC: 5205A-01
For 3m & 10 m OATS
1.3 Details of Applicant
Name: FUJIAN NAN’AN BAOFENG ELECTRONICS CO., LTD.
Address: CHANGFU INDUSTRIAL ZONE, XIAMEI, NAN’AN, QUANZHOU, FUJIAN, CHINA
1. 4 Application Details
Date of Receipt of Application: March 15, 2011
Date of Receipt of Test Item: March 15, 2011
Date of Test: March 15, 2011- March 28, 2011
1.5 Test Item
Manufacturer: FUJIAN NAN’AN BAOFENG ELECTRONICS CO., LTD.
Address: CHANGFU INDUSTRIAL ZONE, XIAMEI, NAN’AN, QUANZHOU, FUJIAN, CHINA
Brand Name: BAOFENG
Model No.: UV-3R
Additional Brand Name: N/A
Additional Model No.: N/A
Description: Two Way Radio
Report No: 1103180-01
Date: 2011-03-31
Page 5 of 67
TEST REPORT
Additional Information
Frequency: 136-174MHz, 400-470MHz
Channel Separation: 12.5, 25 kHz
Service Areas: N/A
Rated Input: DC3.7V
Operation Environment Temp.: N/A
Power Supply: Model: YC-2011A
1.6 Test Standards
ETSI EN 300 086-1 V1.3.1 (2008-09)
Electromagnetic compatibility and Radio spectrum Matters (ERM);
Land Mobile Service;
Radio equipment with an internal or external RF connector intended primarily for analogue speech;
Part 1: Technical characteristics and methods of measurement
ETSI EN 300 086-2 V1.2.1 (2008-09)
Electromagnetic compatibility and Radio spectrum Matters (ERM);
Land Mobile Service;
Radio equipment with an internal or external RF connector intended primarily for analogue speech;
Part 2: Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive
Note: All radiated measurements were made in all three orthogonal planes. The values reported are the maximum
values.
1.7 Test Engineer
Terry Tang
Report No: 1103180-01
Date: 2011-03-31
Page 6 of 67
TEST REPORT
2. Technical Test
2.1 Summary of Test Results
No deviations from the technical specification(s) were ascertained in the course of the tests Performed
Final Verdict:
(Only “Passed” if all Measurements are “Passed”)
Passed
2.2 Test Report
Test Report Reference
List of Measurements
Parameter to be measured
Clause
Transmitter Parameters
Frequency Error
4.2.1
Carrier Power (conducted)
4.2.2
Effective Radiated Power (Field Strength)
4.2.3
Adjacent and alternate channel power
4.2.4
Unwanted emissions in the spurious domain
4.2.5
Intermodulation Attenuation
4.2.6
Receiver Parameters
Maximum Usable Sensitivity (Conducted)
4.3.1
Co-channel Rejection
4.3.2
Adjacent Channel Selectivity
4.3.3
Spurious Response Rejection
4.3.4
Intermodulation Response Rejection
4.3.5
Blocking or Desensitization
4.3.6
Spurious Radiations
4.3.7
Note: The clause numbers are referenced to ETSI EN 300 086-2 V1.2.1 (2008-09)
Report No: 1103180-01
Date: 2011-03-31
Page 7 of 67
TEST REPORT
2.3 Frequency Error
For Transmitter
Test Configuration:
Test Procedure
1. The method of measurement described under EN 300 086-1, Subclause 7.1.2
2. The test conditions described under EN 300 086-1, Subclause 5.3 and subclause 5.4
Test Results
The Top Channel of 12.5 kHz Channel Separation for 136-174MHz Band
Environment
Temperature(℃)
Power Supplied
(Vdc)
Frequency
Measured (MHz)
Frequency Error
(kHz)
Nominal
Frequency
Limit(kHz)
T nor (25℃)
3.7V
173.97540
+0.40
173.975
±1.50
T min (-20℃)
3.7V
173.97532
+0.32
173.975
±1.50
T min (-20℃)
3.1V
173.97519
+0.19
173.975
±1.50
T max (+55℃)
3.7V
173.97521
+0.21
173.975
±1.50
T max (+55℃)
3.1V
173.97557
+0.57
173.975
±1.50
Report No: 1103180-01
Date: 2011-03-31
Page 8 of 67
TEST REPORT
The Middle Channel of 12.5 kHz Channel Separation for 136-174MHz Band
Environment
Temperature(℃)
Power Supplied
(Vdc)
Frequency
Measured (MHz)
Frequency Error
(kHz)
Nominal
Frequency
Limit(kHz)
T nor (25℃)
3.7V
156.02546
+0.46
156.025
±1.50
T min (-20℃)
3.7V
156.02560
+0.60
156.025
±1.50
T min (-20℃)
3.1V
156.02532
-0.32
156.025
±1.50
T max (+55℃)
3.7V
156.02568
+0.68
156.025
±1.50
T max (+55℃)
3.1V
156.02555
+0.55
156.025
±1.50
The Bottom Channel of 12.5 kHz Channel Separation for 136-174MHz Band
Environment
Temperature(℃)
Power Supplied
(Vdc)
Frequency
Measured (MHz)
Frequency Error
(kHz)
Nominal
Frequency
Limit(kHz)
T nor (25℃)
3.7V
136.02550
+0.50
136.025
±1.00
T min (-20℃)
3.7V
136.02556
+0.56
136.025
±1.00
T min (-20℃)
3.1V
136.02562
+0.62
136.025
±1.00
T max (+55℃)
3.7V
136.02537
+0.37
136.025
±1.00
T max (+55℃)
3.1V
136.02520
+0.20
136.025
±1.00
The Top Channel of 25 kHz Channel Separation for 136-174MHz Band
Environment
Temperature(℃)
Power Supplied
(Vdc)
Frequency
Measured (MHz)
Frequency Error
(kHz)
Nominal
Frequency
Limit(kHz)
T nor (25℃)
3.7V
173.97540
+0.40
173.975
±2.00
T min (-20℃)
3.7V
173.97549
+0.49
173.975
±2.00
T min (-20℃)
3.1V
173.97556
+0.56
173.975
±2.00
T max (+55℃)
3.7V
173.97551
+0.51
173.975
±2.00
T max (+55℃)
3.1V
173.97538
+0.38
173.975
±2.00
Report No: 1103180-01
Date: 2011-03-31
Page 9 of 67
TEST REPORT
The Middle Channel of 25 kHz Channel Separation for 136-174MHz Band
Environment
Temperature(℃)
Power Supplied
(Vdc)
Frequency
Measured (MHz)
Frequency Error
(kHz)
Nominal
Frequency
Limit(kHz)
T nor (25℃)
3.7V
156.02540
+0.40
156.025
±2.00
T min (-20℃)
3.7V
156.02545
+0.45
156.025
±2.00
T min (-20℃)
3.1V
156.02557
+0.57
156.025
±2.00
T max (+55℃)
3.7V
156.02563
+0.63
156.025
±2.00
T max (+55℃)
3.1V
156.02529
+0.29
156.025
±2.00
The Bottom Channel of 25 kHz Channel Separation for 136-174MHz Band
Environment
Temperature(℃)
Power Supplied
(Vdc)
Frequency
Measured (MHz)
Frequency Error
(kHz)
Nominal
Frequency
Limit(kHz)
T nor (25℃)
3.7V
136.02550
+0.50
136.025
±1.35
T min (-20℃)
3.7V
136.02567
+0.67
136.025
±1.35
T min (-20℃)
3.1V
136.02556
+0.56
136.025
±1.35
T max (+55℃)
3.7V
136.02541
+0.41
136.025
±1.35
T max (+55℃)
3.1V
136.02537
+0.37
136.025
±1.35
Report No: 1103180-01
Date: 2011-03-31
Page 10 of 67
TEST REPORT
Environment
Temperature(℃)
Power Supplied
(Vdc)
Frequency
Measured (MHz)
Frequency Error
(kHz)
Nominal
Frequency
Limit(kHz)
T nor (25℃)
3.7V
400.02540
+0.40
400.025
±2.00
T min (-20℃)
3.7V
400.02547
+0.47
400.025
±2.00
T min (-20℃)
3.1V
400.02555
+0.55
400.025
±2.00
T max (+55℃)
3.7V
400.02535
+0.35
400.025
±2.00
T max (+55℃)
3.1V
400.02530
+0.30
400.025
±2.00
Environment
Temperature(℃)
Power Supplied
(Vdc)
Frequency
Measured (MHz)
Frequency Error
(kHz)
Nominal
Frequency
Limit(kHz)
T nor (25℃)
3.7V
435.02520
+0.20
435.025
±2.00
T min (-20℃)
3.7V
435.02528
+0.28
435.025
±2.00
T min (-20℃)
3.1V
435.02533
+0.33
435.025
±2.00
T max (+55℃)
3.7V
435.02512
+0.12
435.025
±2.00
T max (+55℃)
3.1V
435.02518
+0.18
435.025
±2.00
Environment
Temperature(℃)
Power Supplied
(Vdc)
Frequency
Measured (MHz)
Frequency Error
(kHz)
Nominal
Frequency
Limit(kHz)
T nor (25℃)
3.7V
469.97540
+0.40
469.975
±2.00
T min (-20℃)
3.7V
469.97545
+0.45
469.975
±2.00
T min (-20℃)
3.1V
469.97533
+0.33
469.975
±2.00
T max (+55℃)
3.7V
469.97528
+0.28
469.975
±2.00
T max (+55℃)
3.1V
469.97556
+0.56
469.975
±2.00
Report No: 1103180-01
Date: 2011-03-31
Page 11 of 67
TEST REPORT
Environment
Temperature(℃)
Power Supplied
(Vdc)
Frequency
Measured (MHz)
Frequency Error
(kHz)
Nominal
Frequency
Limit(kHz)
T nor (25℃)
3.7V
400.02530
+0.30
400.025
±1.50
T min (-20℃)
3.7V
400.02542
+0.42
400.025
±1.50
T min (-20℃)
3.1V
400.02541
+0.41
400.025
±1.50
T max (+55℃)
3.7V
400.02528
+0.28
400.025
±1.50
T max (+55℃)
3.1V
400.02539
+0.39
400.025
±1.50
Environment
Temperature(℃)
Power Supplied
(Vdc)
Frequency
Measured (MHz)
Frequency Error
(kHz)
Nominal
Frequency
Limit(kHz)
T nor (25℃)
3.7V
435.02530
+0.30
435.025
±1.50
T min (-20℃)
3.7V
435.02546
+0.46
435.025
±1.50
T min (-20℃)
3.1V
435.02535
+0.35
435.025
±1.50
T max (+55℃)
3.7V
435.02537
+0.37
435.025
±1.50
T max (+55℃)
3.1V
435.02546
+0.46
435.025
±1.50
Environment
Temperature(℃)
Power Supplied
(Vdc)
Frequency
Measured (MHz)
Frequency Error
(kHz)
Nominal
Frequency
Limit(kHz)
T nor (25℃)
3.7V
469.97530
+0.30
469.975
±1.50
T min (-20℃)
3.7V
469.97538
+0.38
469.975
±1.50
T min (-20℃)
3.1V
469.97521
+0.21
469.975
±1.50
T max (+55℃)
3.7V
469.97525
+0.25
469.975
±1.50
T max (+55℃)
3.1V
469.97544
+0.44
469.975
±1.50
Report No: 1103180-01
Date: 2011-03-31
Page 12 of 67
TEST REPORT
Limits: EN 300 086-1, subclause 7.1.3
The frequency error shall not exceed the Values given in table 2.
Report No: 1103180-01
Date: 2011-03-31
Page 13 of 67
TEST REPORT
2.4 Carrier Power
For Transmitter
Test Configuration
Test Procedure
1.
2.
The method of measurement described under EN 300 086-1, Subclause 7.2.2
The test conditions described under EN 300 086-1, Subclause 5.3 and 5.4
Test Result
Power Measured
Power Error
(dBm)
(dB)
3.7
32.01
-1.00
3.7
32.12
-0.89
3.1
31.87
-1.14
3.7
32.08
-0.93
3.1
31.92
-1.09
Test Conditions
Temperature (℃)
Voltage (V)
T Nor (25℃)
T min (-20℃)
T Max (+55℃)
Nominal Power=33.01dBm
Result
Pass
Report No: 1103180-01
Date: 2011-03-31
Page 14 of 67
TEST REPORT
Power Measured
Power Error
(dBm)
(dB)
3.7
32.15
-0.86
3.7
32.23
-0.78
3.1
32.09
-0.92
3.7
32.11
-0.90
3.1
32.06
-0.95
Test Conditions
Temperature (℃)
Voltage (V)
T Nor (25℃)
T min (-20℃)
T Max (+55℃)
Result
Pass
The Top Channel of 12.5 kHz Channel Separation 136-174MHz Band
Test Conditions
Temperature (℃)
Power Measured
Power Error
(dBm)
(dB)
3.7
32.44
-0.57
3.7
32.32
-0.69
3.1
32.29
-0.72
3.7
32.51
-0.50
3.1
32.28
-0.73
Voltage (V)
T Nor (25℃)
T min (-20℃)
T Max (+55℃)
Result
Pass
Report No: 1103180-01
Date: 2011-03-31
Page 15 of 67
TEST REPORT
The Top Channel of 25 kHz Channel Separation 136-174MHz Band
Test Conditions
Temperature (℃)
Voltage (V)
T Nor (25℃)
3.7
3.7
T min (-20℃)
3.1
3.7
T Max (+55℃)
3.1
Power Measured
Power Error
(dBm)
(dB)
32.26
-0.75
32.32
-0.69
32.14
-0.87
32.34
-0.67
32.11
-0.90
Result
Pass
The Middle Channel of 25 kHz Channel Separation 136-174MHz Band
Test Conditions
Temperature (℃)
Voltage (V)
T Nor (25℃)
3.7
3.7
T min (-20℃)
3.1
3.7
T Max (+55℃)
3.1
Power Measured
Power Error
(dBm)
(dB)
32.25
-0.76
32.33
-0.68
32.16
-0.85
32.19
-0.82
32.09
-0.92
Result
Pass
Report No: 1103180-01
Date: 2011-03-31
Page 16 of 67
TEST REPORT
The Bottom Channel of 25 kHz Channel Separation 136-174MHz Band
Test Conditions
Temperature (℃)
Voltage (V)
T Nor (25℃)
3.7
3.7
T min (-20℃)
3.1
3.7
T Max (+55℃)
3.1
Power Measured
Power Error
(dBm)
(dB)
32.58
-0.43
32.61
-0.40
32.50
-0.51
32.66
-0.35
32.41
-0.60
Result
Pass
Test Conditions
Temperature (℃)
Power Measured
Power Error
(dBm)
(dB)
3.7
33.13
0.12
3.7
33.25
0.24
3.1
32.92
-0.09
3.7
33.17
0.16
3.1
32.89
-0.12
Voltage (V)
T Nor (25℃)
T min (-20℃)
T Max (+55℃)
Result
Pass
Report No: 1103180-01
Date: 2011-03-31
Page 17 of 67
TEST REPORT
Test Conditions
Temperature (℃)
Power Measured
Power Error
(dBm)
(dB)
3.7
32.85
-0.16
3.7
32.98
-0.03
3.1
32.77
-0.24
3.7
32.83
-0.18
3.1
32.85
-0.16
Voltage (V)
T Nor (25℃)
T min (-20℃)
T Max (+55℃)
Result
Pass
Test Conditions
Temperature (℃)
Power Measured
Power Error
(dBm)
(dB)
3.7
32.35
-0.66
3.7
32.40
-0.61
3.1
32.29
-0.72
3.7
32.32
-0.69
3.1
32.29
-0.72
Voltage (V)
T Nor (25℃)
T min (-20℃)
T Max (+55℃)
Result
Pass
Report No: 1103180-01
Date: 2011-03-31
Page 18 of 67
TEST REPORT
Power Measured
Power Error
(dBm)
(dB)
3.7
33.19
0.18
3.7
33.23
0.22
3.1
33.02
0.01
3.7
33.26
0.25
3.1
33.09
0.08
Test Conditions
Temperature (℃)
Voltage (V)
T Nor (25℃)
T min (-20℃)
T Max (+55℃)
Result
Pass
Test Conditions
Temperature (℃)
Power Measured
Power Error
(dBm)
(dB)
3.7
32.79
-0.22
3.7
32.86
-0.15
3.1
32.58
-0.43
3.7
32.83
-0.18
3.1
32.75
-0.26
Voltage (V)
T Nor (25℃)
T min (-20℃)
T Max (+55℃)
Result
Pass
Report No: 1103180-01
Date: 2011-03-31
Page 19 of 67
TEST REPORT
Test Conditions
Temperature (℃)
Power Measured
Power Error
(dBm)
(dB)
3.7
32.49
-0.52
3.7
32.56
-0.45
3.1
32.38
-0.63
3.7
32.46
-0.55
3.1
32.21
-0.80
Voltage (V)
T Nor (25℃)
T min (-20℃)
T Max (+55℃)
Result
Pass
Limits: EN 300 086-1, subclause 5.1.2
The transmitter power (conducted) under the specified conditions of measurement (see clause 7.2.2) and at normal
test conditions (see clause 5.3), shall be within ±1,5 dB of the rated carrier power (conducted). The transmitter
power (conducted) under extreme test conditions (see clause 5.4) shall be within +2,0 dB and -3,0 dB of the rated
output power.
Report No: 1103180-01
Date: 2011-03-31
Page 20 of 67
TEST REPORT
2.5 Maximum Effective Radiated Power (Field Strength)
(Not Applicable to Device with External RF Port)
Test Configuration
N/A
Test Procedure
N/A
Test Results
N/A
2.6 Frequency Deviation
Test Configuration
Test Procedure
1.
2.
The method of measurement described under EN 300 086-1, Subclause 7.4.2.1 and 7.4.2.2
The test conditions described under EN 300 086-1, Subclause 5.3
Report No: 1103180-01
Date: 2011-03-31
Page 21 of 67
TEST REPORT
Test Result
Modulation Frequency (kHz)
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.2
1.4
1.6
1.8
2.0
2.2
2.4
2.55
2.6
2.8
3.0
3.5
4.0
4.5
5.0
6.0
8.0
10.0
12.0
14.0
16.0
20.0
25.0
Deviation (kHz)
1.73
1.67
1.83
1.92
1.85
1.96
2.03
1.96
1.99
1.89
1.82
1.71
1.66
1.55
1.57
1.46
1.31
1.09
0.85
0.72
0.62
0.51
0.33
0.26
0.16
0.11
0.07
0.05
0.04
0.02
0.01
Report No: 1103180-01
Date: 2011-03-31
Page 22 of 67
TEST REPORT
The Middle Channel of 12.5 kHz Channel Separation for 400-470MHz
Deviation (kHz)
0.3
1.72
0.4
1.77
0.5
1.89
0.6
1.93
0.7
1.86
0.8
2.01
0.9
2.02
1.0
1.93
1.2
2.02
1.4
1.93
1.6
1.89
1.8
1.73
2.0
1.62
2.2
1.55
2.4
1.62
2.55
1.56
2.6
1.40
2.8
1.32
3.0
1.22
3.5
1.09
4.0
0.83
4.5
0.60
5.0
0.45
6.0
0.33
8.0
0.15
10.0
0.11
12.0
0.10
14.0
0.08
16.0
0.06
20.0
0.03
25.0
0.02
Report No: 1103180-01
Date: 2011-03-31
Page 23 of 67
TEST REPORT
Deviation (kHz)
0.3
1.72
0.4
1.68
0.5
1.87
0.6
1.92
0.7
2.02
0.8
2.04
0.9
1.97
1.0
2.06
1.2
1.90
1.4
1.87
1.6
1.75
1.8
1.71
2.0
1.67
2.2
1.82
2.4
1.76
2.6
1.81
2.8
1.70
3.0
1.58
3.5
1.32
4.0
0.91
4.5
0.65
5.0
0.55
6.0
0.38
8.0
0.16
10.0
0.12
12.0
0.08
14.0
0.04
16.0
0.02
20.0
0.02
25.0
0.01
Report No: 1103180-01
Date: 2011-03-31
Page 24 of 67
TEST REPORT
Deviation (kHz)
0.3
1.73
0.4
1.82
0.5
1.93
0.6
2.09
0.7
2.12
0.8
2.18
0.9
2.11
1.0
1.96
1.2
1.87
1.4
1.92
1.6
2.02
1.8
1.92
2.0
1.83
2.2
1.80
2.4
1.88
2.6
1.82
2.8
1.79
3.0
1.62
3.5
1.39
4.0
1.16
4.5
0.65
5.0
0.55
6.0
0.37
8.0
0.22
10.0
0.12
12.0
0.08
14.0
0.06
16.0
0.04
20.0
0.02
25.0
0.02
Report No: 1103180-01
Date: 2011-03-31
Page 25 of 67
TEST REPORT
Limit
ETSI EN 300 086-1 Subclause 7.4.3.1
The maximum permissible frequency deviation for modulation frequencies from the lowest frequency transmitted
(f1)
by the equipment (as declared by the manufacturer) up to (f2) shall be as given in table 3.
ETSI EN 300 086-1 Subclause 7.4.3.2
The frequency deviation at modulation frequencies between 3,0 kHz (for equipment operating with 20 kHz or 25
kHz channel separations) and 2,55 kHz (for equipment operating with 12,5 kHz channel separation) and 6,0 kHz
shall not exceed the frequency deviation at a modulation frequency of 3,0 kHz/2,55 kHz. At 6,0 kHz the deviation
shall be not more than 30,0 % of the maximum permissible frequency deviation.
The frequency deviation at modulation frequencies between 6,0 kHz and a frequency equal to the channel
separation for which the equipment is intended shall not exceed that given by a linear representation of the
frequency deviation (dB) relative to the modulation frequency, starting at the 6,0 kHz limit and having a slope of
-14,0 dB per octave. These limits are illustrated in figure 6.
Report No: 1103180-01
Date: 2011-03-31
Page 26 of 67
TEST REPORT
Report No: 1103180-01
Date: 2011-03-31
Page 27 of 67
TEST REPORT
2.7 Adjacent and alternate channel power
Test Configuration
Test Procedure
1.
2.
The method of measurement described under EN 300 086-1, Subclause 7.5.2
The test conditions described under EN 300 086-1, Subclause 5.3
Report No: 1103180-01
Date: 2011-03-31
Page 28 of 67
TEST REPORT
Test Results
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
Adjacent Channel Power (dBm)
+8.25kHz
-58.2
Voltage(V)
V Nor (3.7V)
-58.1
-8.25kHz
Applicable Limit
60dB down or 0.2uW
Result
Pass
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
+8.25kHz
-58.6
Voltage(V)
V Nor (3.7V)
-58.5
-8.25kHz
Applicable Limit
60dB down or 0.2uW
Result
Pass
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
+8.25kHz
-59.1
Voltage(V)
V Nor (3.7V)
-59.3
-8.25kHz
Applicable Limit
60dB down or 0.2uW
Result
Pass
Report No: 1103180-01
Date: 2011-03-31
Page 29 of 67
TEST REPORT
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
+8.25kHz
-57.7
Voltage(V)
V Nor (3.7V)
-57.8
-8.25kHz
Applicable Limit
60dB down or 0.2uW
Result
Pass
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
+8.25kHz
-57.6
Voltage(V)
V Nor (3.7V)
-57.5
-8.25kHz
Applicable Limit
60dB down or 0.2uW
Result
Pass
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
+8.25kHz
-57.8
Voltage(V)
V Nor (3.7V)
-57.6
-8.25kHz
Applicable Limit
60dB down or 0.2uW
Result
Pass
Report No: 1103180-01
Date: 2011-03-31
Page 30 of 67
TEST REPORT
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
+17kHz
-59.8
Voltage(V)
V Nor (3.7V)
-59.6
-17kHz
Applicable Limit
60dB down or 0.2uW
Result
Pass
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
+17kHz
-59.9
Voltage(V)
V Nor (3.7V)
-60.1
-17kHz
Applicable Limit
60dB down or 0.2uW
Result
Pass
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
+17kHz
-60.3
Voltage(V)
V Nor (3.7V)
-60.2
-17kHz
Applicable Limit
60dB down or 0.2uW
Result
Pass
Report No: 1103180-01
Date: 2011-03-31
Page 31 of 67
TEST REPORT
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
+17kHz
-58.7
Voltage(V)
V Nor (3.7V)
-58.8
-17kHz
Applicable Limit
60dB down or 0.2uW
Result
Pass
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
+17kHz
-59.1
Voltage(V)
V Nor (3.7V)
-59.1
-17kHz
Applicable Limit
60dB down or 0.2uW
Result
Pass
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
+17kHz
-58.7
Voltage(V)
V Nor (3.7V)
-58.6
-17kHz
Applicable Limit
60dB down or 0.2uW
Result
Pass
Report No: 1103180-01
Date: 2011-03-31
Page 32 of 67
TEST REPORT
Test Condition
Measurement Offset
Temperature (℃)
Alternate Channel Power (dBm)
Voltage(V)
+20.25kHz
T Nor (25℃)
-69.3
V Nor (3.7V)
-69.2
-20.25kHz
Applicable Limit
70dB down or 0.2uW
Result
Pass
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
+20.25kHz
-69.1
Voltage(V)
V Nor (3.7V)
-69.2
-20.25kHz
Applicable Limit
70dB down or 0.2uW
Result
Pass
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
+20.25kHz
-69.4
Voltage(V)
V Nor (3.7V)
-69.5
-20.25kHz
Applicable Limit
70dB down or 0.2uW
Result
Pass
Report No: 1103180-01
Date: 2011-03-31
Page 33 of 67
TEST REPORT
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
+42kHz
-67.6
Voltage(V)
V Nor (3.7V)
-67.4
-42kHz
Applicable Limit
70dB down or 0.2uW
Result
Pass
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
+42kHz
-67.8
Voltage(V)
V Nor (3.7V)
-67.7
-42kHz
Applicable Limit
70dB down or 0.2uW
Result
Pass
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
+42kHz
-67.2
Voltage(V)
V Nor (3.7V)
-67.4
-42kHz
Applicable Limit
70dB down or 0.2uW
Result
Pass
Report No: 1103180-01
Date: 2011-03-31
Page 34 of 67
TEST REPORT
The Top Channel of 12.5 kHz Channel Separation for400-470MHz Band
Test Condition
Measurement Offset
Temperature (℃)
Voltage(V)
+20.25kHz
T Nor (25℃)
-68.6
V Nor (3.7V)
-68.8
-20.25kHz
Applicable Limit
70dB down or 0.2uW
Result
Pass
The Middle Channel of 12.5 kHz Channel Separation for400-470MHz Band
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
+20.25kHz
-68.4
Voltage(V)
V Nor (3.7V)
-68.3
-20.25kHz
Applicable Limit
70dB down or 0.2uW
Result
Pass
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
+20.25kHz
-68.2
Voltage(V)
V Nor (3.7V)
-68.1
-20.25kHz
Applicable Limit
70dB down or 0.2uW
Result
Pass
Report No: 1103180-01
Date: 2011-03-31
Page 35 of 67
TEST REPORT
The Top Channel of 25 kHz Channel Separation for400-470MHz Band
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
+42kHz
-66.3
Voltage(V)
V Nor (3.7V)
-66.4
-42kHz
Applicable Limit
70dB down or 0.2uW
Result
Pass
The Bottom Channel of 25 kHz Channel Separation for400-470MHz Band
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
+42kHz
-66.6
Voltage(V)
V Nor (3.7V)
-66.3
-42kHz
Applicable Limit
70dB down or 0.2uW
Result
Pass
Test Condition
Temperature (℃)
T Nor (25℃)
Measurement Offset
+42kHz
-66.3
Voltage(V)
V Nor (3.7V)
-66.5
-42kHz
Applicable Limit
70dB down or 0.2uW
Result
Pass
Limit
For a channel separation of 12,5 kHz, 20 kHz and 25 kHz, the adjacent channel power shall not exceed a value of
60,0 dB below the transmitter power (conducted) without the need to be below 0,2 μW (-37 dBm). For a channel
separation of 12,5 kHz, 20 kHz and 25 kHz, the alternate channel power shall not exceed a value of 70,0 dB
below the transmitter power (conducted) without the need to be below 0,2 μW (-37 dBm).
Report No: 1103180-01
Date: 2011-03-31
Page 36 of 67
TEST REPORT
2.8 Unwanted emissions in the spurious domain
Test Configuration
Conducted Measurement (9 kHz to 4GHz)
Effective Radiated Power measurement (30MHz to 4GHz)
Below 1G
Report No: 1103180-01
Date: 2011-03-31
Page 37 of 67
TEST REPORT
Above 1GHz
Report No: 1103180-01
Date: 2011-03-31
Page 38 of 67
TEST REPORT
Test Procedure
1. Please refer to ETSI EN 300 086-1 (V1.3.1) Sub-clause 5.3 for the test conditions.
2. Please refer to ETSI EN 300 086-1 (V1.3.1) Sub-clause 7.6.2 and 7.6.3 for the measurement method
Test Results
Both the conducted measurement and radiated measurement are performed to the three channels
Conducted Measurement (9 kHz to 4GHz)
The Bottom Channel of 12.5 KHz Channel separation for 136-174 MHz Band
Test Condition
Conducted Power
(dBm)
Frequency (MHz)
Temperature (℃)
T Nor ( 25 ℃)
Voltage (V)
V Nor (3.7V)
272.05
-42.2
408.08
-48.3
544.12
-52.1
Result
Pass
The Bottom Channel of 25 kHz Channel Separation for 136-174 MHz Band
Test Condition
Conducted Power
(dBm)
Frequency (MHz)
Temperature (℃)
T Nor ( 25 ℃)
Result
Voltage (V)
V Nor (3.7V)
272.05
-42.8
408.08
-48.1
544.12
-53.2
Pass
Report No: 1103180-01
Date: 2011-03-31
Page 39 of 67
TEST REPORT
The Top Channel of 12.5 kHz Channel Separation for 136-174 MHz Band
Test Condition
Temperature (℃)
T Nor ( 25 ℃)
Conducted Power
(dBm)
Frequency (MHz)
Voltage (V)
V Nor (7.4V)
347.95
-56.7
521.93
-67.5
Result
Pass
The Top Channel of 25 kHz Channel Separation for 136-174 MHz Band
Test Condition
Temperature (℃)
T Nor ( 25 ℃)
Conducted Power
(dBm)
Frequency (MHz)
Voltage (V)
V Nor (7.4V)
347.95
-56.5
521.93
-67.2
Result
Pass
The Bottom Channel of 12.5 KHz Channel separation for 400-470 MHz Band
Test Condition
Conducted Power
(dBm)
Frequency (MHz)
Temperature (℃)
T Nor ( 25 ℃)
Voltage (V)
V Nor (3.7V)
800.05
-46.7
1200.08
-63.7
1600.12
-52.4
Result
Pass
The Bottom Channel of 25 kHz Channel Separation for 400-470 MHz Band
Test Condition
Conducted Power
(dBm)
Frequency (MHz)
Temperature (℃)
T Nor ( 25 ℃)
Result
Voltage (V)
V Nor (3.7V)
800.05
-46.2
1200.08
-64.0
1600.12
-52.7
Pass
Report No: 1103180-01
Date: 2011-03-31
Page 40 of 67
TEST REPORT
The Top Channel of 12.5 KHz Channel separation for 400-470 MHz Band
Test Condition
Conducted Power
(dBm)
Frequency (MHz)
Temperature (℃)
T Nor ( 25 ℃)
Voltage (V)
V Nor (3.7V)
939.95
-50.4
1409.93
-48.0
1879.92
-60.9
Result
The Top Channel of 25 kHz Channel Separation for 400-470 MHz Band
Test Condition
Conducted Power
(dBm)
Frequency (MHz)
Temperature (℃)
T Nor ( 25 ℃)
Voltage (V)
V Nor (3.7V)
939.95
-50.2
1409.93
-48.1
1879.92
-60.5
Result
Pass
Effective Radiated Power measurement (30MHz to 4GHz or 12.75GHz)
For 12.5 kHz/ 25 kHz channel separation
Frequency (MHz）
Emission Level (dBm)
Limit
Margin (dB)
NF
--
--
--
NF
--
--
--
NF
--
--
--
NF
--
--
--
NF=No peak value was found
Notes:
For the receiving mode is the standby mode, all the test data and applicable limit, both conducted and
radiated, is acquired from the operating mode.
Limit
The power of any spurious radiation shall not exceed the values given in tables 5a and 5b.
Report No: 1103180-01
Date: 2011-03-31
Page 41 of 67
TEST REPORT
Report No: 1103180-01
Date: 2011-03-31
Page 42 of 67
TEST REPORT
2.9 Intermediation attenuation
(Not applicable to this portable device)
Test Configuration
N/A
Test Procedure
N/A
Test Results
N/A
Limit
Two classes of transmitter intermodulation attenuation are defined, the equipment shall fulfil one of the
requirements as
follows:
- the intermodulation attenuation ratio shall be at least 40,0 dB for any intermodulation component;
- for base stations to be used in special service conditions (e.g. at sites where more than one transmitter will be in
service) or when the regulatory authority makes it a condition of the licence, the intermodulation attenuation
ratio shall be at least 70,0 dB for any intermodulation component. In the case where the performance is
achieved by additional internal or external isolating devices (such as circulators) these are expected to be
available at the time the measurements are made and shall be used for the measurements.
Report No: 1103180-01
Date: 2011-03-31
Page 43 of 67
TEST REPORT
Receiver Parameters
2.10 Maximum Usable Sensitivity (Conducted)
Test Configuration
Test Procedure
1. Please refer to ETSI EN 300 086-1 (V1.3.1) Sub-clause 5.3 and 5.4 for the test conditions
2. Please refer to ETSI EN 300 086-1 (V1.3.1) Sub-clause 8.1.2 for the measurement method
Test Result
12.5 kHz Channel Separation for 136-174MHz Band
Test condition
Temperature (℃)
Result Measured
(dBuV)
Limit
(dBuV)
3.7
4.7
6.0
3.7
4.8
12
3.1
5.2
12
3.7
5.1
12
3.1
5.5
12
Voltage (V)
T Nor (25℃)
T Min (-20℃)
T Max (+55℃)
Result
Pass
Report No: 1103180-01
Date: 2011-03-31
Page 44 of 67
TEST REPORT
25 kHz Channel Separation for 136-174MHz Band
Result Measured
(dBuV)
Limit
(dBuV)
3.7
4.6
6.0
3.7
5.3
12
3.1
5.5
12
3.7
5.8
12
3.1
6.0
12
Test condition
Temperature (℃)
Voltage (V)
T Nor (25℃)
T Min (-20℃)
T Max (+55℃)
Result
Pass
Test condition
Temperature (℃)
Result Measured
(dBuV)
Limit
(dBuV)
3.7
4.3
6.0
3.7
5.1
12
3.1
5.3
12
3.7
4.8
12
3.1
4.7
12
Voltage (V)
T Nor (25℃)
T Min (-20℃)
T Max (+55℃)
Result
Pass
25 kHz Channel Separation for 400-470MHz Band
Test condition
Temperature (℃)
Result Measured
(dBuV)
Limit
(dBuV)
3.7
4.3
6.0
3.7
4.9
12
3.1
5.2
12
3.7
5.5
12
3.1
4.9
12
Voltage (V)
T Nor (25℃)
T Min (-20℃)
T Max (+55℃)
Result
Pass
Limit
The maximum usable sensitivity shall not exceed an electromotive force (emf) of +6,0 dBμV under normal test
conditions, and an emf of +12,0 dBμV under extreme test conditions.
Report No: 1103180-01
Date: 2011-03-31
Page 45 of 67
TEST REPORT
2.11 Maximum Usable Sensitivity (Field Strength)
( Not Applicable to Device With External RF Port)
Test Configuration
N/A
Test Procedure
N/A
Test Results
N/A
Limit
Report No: 1103180-01
Date: 2011-03-31
Page 46 of 67
TEST REPORT
2.12 Co-Channel Rejection
Test Configuration
Test Procedure
1. Please refer to ETSI EN 300 086-1 (V1.3.1) Sub-clause 6.3 for the test conditions
Test Result
Test Result of 12.5 kHz Channel Separation for 136-174MHz Band
Test Result (dB)
Limit (dB)
-4.5
Between -12dB to 0dB
Result
Pass
Test Result of 25 kHz Channel Separation for 136-174MHz Band
Test Result (dB)
Limit (dB)
-4.1
Between -8dB to 0dB
Result
Pass
Report No: 1103180-01
Date: 2011-03-31
Page 47 of 67
TEST REPORT
Test Result (dB)
Limit (dB)
-5.1
Between -12dB to 0dB
Result
Pass
Test Result (dB)
Limit (dB)
-4.4
Between -8dB to 0dB
Result
Pass
Limit
The value of the co-channel rejection ratio, expressed in dB, at any frequency of the unwanted signal within the
specified range, shall be between:
-8.0 dB and 0 dB for channel separations of 20 kHz and 25 kHz;
-12.0 dB and 0 dB for channel separation of 12.5 kHz.
Report No: 1103180-01
Date: 2011-03-31
Page 48 of 67
TEST REPORT
2.13Adjacent Channel Selectivity
Test Configuration
Test Procedure
1. Please refer to ETSI EN 300 086-1 (V1.3.1) Sub-clause 6.3 and 6.4for the test conditions
Test Result
Test Condition
Temperature (℃)
T Nor (25℃)
T min (-20℃)
T Max (+55℃)
Result
Result Measured (dB)
Limit (dB)
3.7
68
60
3.7
65
50
3.1
62
50
3.7
63
50
3.1
61
50
Voltage (V)
Pass
Report No: 1103180-01
Date: 2011-03-31
Page 49 of 67
TEST REPORT
Test Condition
Temperature (℃)
T Nor (25℃)
T min (-20℃)
T Max (+55℃)
Limit (dB)
3.7
75
70
3.7
68
60
3.1
70
60
3.7
72
60
3.1
69
60
Voltage (V)
Result
Pass
Test Condition
Temperature (℃)
T Nor (25℃)
T min (-20℃)
T Max (+55℃)
Limit (dB)
3.7
69
60
3.7
63
50
3.1
60
50
3.7
65
50
3.1
62
50
Voltage (V)
Result
Pass
Test Condition
Temperature (℃)
T Nor (25℃)
T min (-20℃)
T Max (+55℃)
Result
Limit (dB)
3.7
75
70
3.7
70
60
3.1
68
60
3.7
71
60
3.1
67
60
Voltage (V)
Pass
Limit
Report No: 1103180-01
Date: 2011-03-31
Page 50 of 67
TEST REPORT
2.14 Spurious Response Rejection
Test Procedure
The same as describe in section 2.14
Test procedure
Test Result
Test Result (dB)
Limit (dB)
77.2
At least 70dB
Result
Pass
Test Result (dB)
Limit (dB)
78.1
At least 70dB
Result
Pass
Test Result (dB)
Limit (dB)
78.0
At least 70dB
Result
Pass
Test Result (dB)
Limit (dB)
79.3
At least 70dB
Result
Pass
Limit
At any frequency separated from the nominal frequency of the receiver by more than one channel, the spurious
response rejection ratio shall not be less than 70,0 dB.
Report No: 1103180-01
Date: 2011-03-31
Page 51 of 67
TEST REPORT
2.15 Intermodulation Response Rejection
Test Configuration
Test procedure
Test Result
Test Result (dB)
Limit (dB)
72.1
At least 65dB
Result
Pass
Test Result (dB)
Limit (dB)
72.5
At least 65dB
Result
Pass
Report No: 1103180-01
Date: 2011-03-31
Page 52 of 67
TEST REPORT
Test Result (dB)
Limit (dB)
74.4
At least 65dB
Result
Pass
Test Result (dB)
Limit (dB)
74.9
At least 65dB
Result
Pass
Limit
The intermodulation response rejection ratio shall not be less than 70,0 dB for base stations and 65,0 dB for
mobile and hand portable stations.
Report No: 1103180-01
Date: 2011-03-31
Page 53 of 67
TEST REPORT
2.16 Block Or Desensitization
Test Configuration
The same as described in section 2.14
Test Procedure
Test Result
Test Result (dB)
Limit (dB)
95.1
At least 84dB
Result
Pass
Test Result (dB)
Limit (dB)
93.6
At least 84dB
Result
Pass
Test Result (dB)
Limit (dB)
96.2
At least 84dB
Result
Pass
Test Result (dB)
Limit (dB)
96.5
At least 84dB
Result
Pass
Limit
The blocking ratio for any frequency within the specified ranges shall not be less than 84,0 dB, except at
frequencies on which spurious responses are found.
Report No: 1103180-01
Date: 2011-03-31
Page 54 of 67
TEST REPORT
2.17 Spurious Radiation
Test Configuration
Test Procedure
Test Result
The Radiated Measurement are performed to the three channels ( the top channel , the middle channel and the
bottom channel), the data recorded blow is the worse case for each channel separation
The Top Channel is the worse case for 12.5 kHz Channel Separation for 136-174MHz Band
Frequency (MHz）
Limit
Margin (dB)
NF
--
--
NF
--
--
NF
--
--
At least 20
less than the
Limit
NF
--
--
The Top Channel is the worse case for 12.5 kHz Channel Separation For 400-470MHz Band
Frequency (MHz）
Limit
Margin (dB)
NF
--
--
NF
--
--
NF
--
--
At least 20
less than the
Limit
NF
--
--
Note: NF=No peak value was found
Report No: 1103180-01
Date: 2011-03-31
Page 55 of 67
TEST REPORT
Test plots:
Report No: 1103180-01
Date: 2011-03-31
Page 56 of 67
TEST REPORT
Report No: 1103180-01
Date: 2011-03-31
Page 57 of 67
TEST REPORT
Limit
The power of any spurious radiation shall not exceed the values given in tables 7 and 8.
Report No: 1103180-01
Date: 2011-03-31
3.0
Page 58 of 67
TEST REPORT
Product Labelling
CE Mark label specification
Text of the mark is black or white in colour and is left justified. Labels are printed in indelible ink on
permanent adhesive backing and shall be affixed at a conspicuous location on the EUT or
silk-screened onto the EUT.
Mark Location: Rear enclosure
Proposed Label Location On EUT
EUT Bottom View/Proposed CE Mark Location
Mark
location
Report No: 1103180-01
Date: 2011-03-31
Page 59 of 67
TEST REPORT
4. Photographs – Test Setup
Radiated emission test view
Report No: 1103180-01
Date: 2011-03-31
Page 60 of 67
TEST REPORT
5. Photographs - EUT
EUT View
Report No: 1103180-01
Date: 2011-03-31
Page 61 of 67
TEST REPORT
EUT Outside View
Report No: 1103180-01
Date: 2011-03-31
Page 62 of 67
TEST REPORT
EUT Outside View
Report No: 1103180-01
Date: 2011-03-31
Page 63 of 67
TEST REPORT
EUT Inside View
Report No: 1103180-01
Date: 2011-03-31
Page 64 of 67
TEST REPORT
EUT Inside View
UHF Antenna
VHF Antenna
Report No: 1103180-01
Date: 2011-03-31
Page 65 of 67
TEST REPORT
EUT Inside View
Report No: 1103180-01
Date: 2011-03-31
Page 66 of 67
TEST REPORT
6.0
Test Equipments
Instrument Type
Manufacturer
Model
Serial No.
Date of Cal.
Due Date
ESPI Test Receiver
ROHDE&SCHWARZ
ESPI 3
100379
2010-12-04
2011-12-03
Absorbing Clamp
ROHDE&SCHWARZ
MDS-21
100126
2010-12-04
2011-12-03
TWO
Line-V-NETW
ROHDE&SCHWARZ
EZH3-Z5
100294
2010-12-04
2011-12-03
TWO
Line-V-NETW
ROHDE&SCHWARZ
EZH3-Z5
100253
2010-12-04
2011-12-03
ROHDE&SCHWARZ
HL562
100157
2010-12-04
2011-12-03
ROHDE&SCHWARZ
ESDV
100008
2011-03-02
2012-03-01
ROHDE&SCHWARZ
ENY 41
830663/044
2011-03-02
2012-03-01
GG ENY22 Double
2-Wire ISN
ROHDE&SCHWARZ
ENY22
83066/016
2011-03-02
2012-03-01
Impuls-Begrenzer
ROHDE&SCHWARZ
ESH3-Z2
100281
2011-03-02
2012-03-01
System Controller
CT
SC100
-
2011-03-02
2012-03-01
Printer
EPSON
PHOTO EX3
CFNH234850
2011-03-02
2012-03-01
FM-AM Signal
Generator
JUNG.JIN
SG-150M
389911177
2011-03-02
2012-03-01
Color TV Pattern
Generator
PHILIPS
PM5418
LO621747
2011-03-02
2012-03-01
Computer
IBM
8434
1S8434KCE99BLXL
O*
-
-
Oscillator
KENWOOD
AG-203D
3070002
2011-03-02
2012-03-01
Spectrum Analyzer
HAMEG
HM5012
-
-
-
Power Supply
LW
APS1502
-
-
-
5K VA AC Power
Source
California Instruments
5001iX
56060
2011-03-02
2012-03-01
CDN
EM TEST
CDN M2/M3
-
2011-03-02
2012-03-01
Attenuation
EM TEST
ATT6/75
-
2011-03-02
2012-03-01
Resistance
EM TEST
R100
-
2011-03-02
2012-03-01
Electromagnetic
Injection Clamp
LITTHI
EM101
35708
2011-03-02
2012-03-01
Inductive
Components
EM TEST
MC2630
-
2011-03-02
2012-03-01
Ultra Broadband
ANT
ESDV Test Receiver
4-WIRE ISN
Report No: 1103180-01
Date: 2011-03-31
Page 67 of 67
TEST REPORT
Antenna
EM TEST
MS100
-
2011-03-02
2012-03-01
Signal Generator
ROHDE&SCHWARZ
SMT03
100029
2011-03-02
2012-03-01
Power Amplifier
AR
150W1000
300999
2011-03-02
2012-03-01
Field probe
Holaday
HI-6005
105152
2011-03-02
2012-03-01
Bilog Antenna
Chase
CBL6111C
2576
2011-03-02
2012-03-01
Loop Antenna
EMCO
6502
00042960
2011-03-02
2012-03-01
ESPI Test Receiver
ROHDE&SCHWARZ
ESI26
838786/013
2011-03-02
2012-03-01
3m OATS
--
--
N/A
2011-03-02
2012-03-01
End of the Report

Test result - Funkamateur

Transcription

Similar documents

IT Report---960719

ce emc test report