cisco catalyst 6500 series 10 gigabit ethernet modules

Transcription

DATA SHEET
CISCO CATALYST 6500 SERIES
10 GIGABIT ETHERNET MODULES
®
®
Cisco’s premier modular multilayer switch, the Cisco Catalyst 6500 Series, delivers secure, converged services from the
wiring closet to the core, to the data center, to the WAN edge.
Figure 1.
Cisco Catalyst 6500 Series CEF720 4-port 10 Gigabit Ethernet Module (WS-X6704-10GE) and installed XENPAKs
PRODUCT OVERVIEW
As the leading switch in 10 Gigabit Ethernet deployments, the Cisco Catalyst 6500 Series delivers nonblocking 10-Gbps performance and high port
density for data centers and network cores. Building upon the award-winning Catalyst 6500 Series, these 10 Gigabit Ethernet modules enable service
providers and enterprises to offer new Layer 2 through 7 services and network capabilities to increase revenue and user productivity without
complete equipment upgrades.
Cisco Catalyst 6500 Series 10-Gigabit Ethernet modules provide a broad selection of features, including:
• Enable New Bandwidth-Intensive Applications—Enable new applications, including storage networking, e-learning, computer hard drive data
backup, imaging and 3D modeling, and grid computing with intensive bandwidth requirements
• Smooth Migration Path from Gigabit EtherChannel® Technology—Attractive price per port encourages Gigabit EtherChannel deployments to
migrate to 10 Gigabit Ethernet
• High 10 Gigabit Ethernet Port Density—High port density, up to 32 ports per system
• Enable Cisco Catalyst 6500 Series End-to-End Solutions—Suitable for distribution, core, and data center traffic aggregation, or for
interbuilding, points of presence (POPs), WAN edge, and MAN connections
• Scalable Performance—Provide a selection of switch fabric connections and throughput options: 32 Gbps, 256 Gbps, and 720 Gbps bandwidth
with system throughput of 15 mpps, 30 mpps, 210 mpps and up to 400 mpps
• Superior Traffic Management—Available with large per-port buffers (up to 256 MB) and up to 16 multiple-priority transmit queues per VLAN
for traffic prioritization and policing
• Choice of Media and Optics—Available in IEEE 802.3ae standard interfaces: 10GBASE-SR (26 m over 62.5-micron FDDI grade multimode
fiber, 300 m over 50-micron 2000 MHz*km multimode fiber) 10GBASE-LR (10 km over single-mode fiber), 10GBASE-ER (40 km over singlemode fiber), 10GBASE-LX4 (300 m over multimode fiber); and IEEE 802.3ak standard interfaces: 10GBASE-CX4 (15 m over copper infiniband
cable); all available in XENPAK form factor for modularity and flexibility in deployment
• Operational Consistency—Supported on Cisco Catalyst 6500 6-, 9-, and 13-slot chassis running Cisco IOS® Software and Cisco Catalyst
Operating System Software; interoperable with all other interfaces and services modules
All contents are Copyright © 1992–2004 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.
Page 1 of 12
• Maximum Network Uptime and Resiliency—Support Cisco enhanced Per-Virtual LAN (VLAN) Spanning Tree Plus (PVST+) protocol, IEEE
802.1w Rapid Spanning Tree Protocol (RSTP) and IEEE 802.1s Multiple Spanning Tree (MST) protocol, Per-VLAN Rapid Spanning Tree
(PVRST) protocol, Hot Standby Router Protocol (HSRP), Virtual Router Redundancy Protocol (VRRP), Cisco EtherChannel technology, and
IEEE 802.3ad link aggregation for fault-tolerant connectivity
• Extensive Management Tools—Support CiscoWorks network management platform; Simple Network Management Protocol (SNMP) versions 1,
2, and 3; and four Remote Monitoring (RMON) groups (statistics, history, alarms, and events) as well as integrated multigigabit network analysis
modules
APPLICATIONS
These 10 Gigabit Ethernet interface modules are suitable for distribution, core, and data center traffic aggregation, or for interbuilding, points of
presence (POPs), WAN edge, and MAN connections. Examples of these applications include data center campus connectivity applications, storage
networking applications, and GRID computing applications.
Data Center Campus Connectivity Applications
Productivity and business continuity are top concerns of companies today. Applications like e-learning and video broadcasting help improve
corporate communications and information sharing anytime, anywhere. Daily desktop backups can be scheduled over the corporate network to
ensure that critical information is not lost when computer hard drives fail. With improved video cameras and picture cameras, digital files are
becoming larger and larger. Having a 10 Gigabit Ethernet data center connectivity prepares the network for e-learning, video broadcasting, and widescale desktop backups applications (Figure 2).
Figure 2.
Applications: Data Center Campus Connectivity
Storage Networking Applications
Storage networking is another application that demands high-bandwidth connection. The growing number of client-server applications, the vast
amount of information on internal Web sites, and the importance of information sharing among teams have expanded the requirements for enterprise
storage and the need for consolidated storage. 10 Gigabit Ethernet with Jumbo frame support is ideal for network attached storage (NAS)
consolidation. To ensure business continuity, companies are also building mirror sites for their data centers at two separate locations. Data stored
© 2004 Cisco Systems, Inc. All right reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 2 of 13
at both sites can be synchronized periodically using 10 Gigabit Ethernet or 10 Gigabit EtherChannel connections to provide instant disaster recovery
(Figure 3).
Figure 3.
Applications: Storage Networking
GRID Computing Applications
GRID Computing—using the network to connect clusters of computers together for parallel processing—is an early adopter of 10 Gigabit Ethernet.
National laboratories, research departments in universities, multimedia companies, oil companies, and financial institutions are building
supercomputers for research, simulation, computer graphics processing, geographic modeling, and financial analyses respectively. 10 Gigabit
Ethernet can be used for aggregation and connection to the supercomputers to provide a fast GRID computing network (Figure 4).
Figure 4.
Applications: GRID Computing
Page 3 of 13
FEATURES AND BENEFITS
Cisco Catalyst 6500 Series switches provide 10 Gigabit Ethernet wire-speed switched connectivity over single-mode fiber, multimode fiber, and
copper. Cisco offers various switch fabric connection and traffic forwarding options, including CEF720 and dCEF720. CEF720 and dCEF720
interface modules communicate using 40-Gbps connections to the integrated 720-Gbps switch fabric of the Supervisor Engine 720.
Cisco also offers a choice of packet buffer depths for traffic shaping, and quality-of-service (QoS) granularity with a varying number of queues and
drop threshold options. These features are important points when considering which module is appropriate for a given network application.
Cisco Catalyst 6500 Series 10 Gigabit Ethernet interfaces can be deployed in a wide variety of environments based on various features (Table 1).
Table 1.
Comparison of 10 Gigabit Ethernet Interface Modules
Feature
WS-X6704-10GE 4 Port x 10 GE, CEF7201*
WS-X6802-10GE 2 port x 10 GE, dCEF720
Primary Application
High-performance enterprise cores and data
High sustained performance service provider and
centers, including Metro Ethernet networks,
enterprise cores and data centers, including Metro
short haul transmission deployments. Add a
Ethernet networks and long-haul transmission
distributed forwarding card (DFC) for high
deployments
sustained performance enterprise or service
provider networks.
Forwarding Architecture and
Switch Fabric Connection
• CEF720: Centralized supervisor engine-based
dCEF720: Full local forwarding (dCEF)
forwarding (CEF) using a 40-Gbps
distributed Cisco Express Forwarding engine
connection to the Supervisor Engine 720’s
using a DFC daughter card on interface module;
720-Gbps switch fabric
uses 40-Gbps connection to the 720-Gbps switch
• Optional full local forwarding (dCEF)
fabric of the Supervisor Engine 720
distributed Cisco Express Forwarding engine
using a field-upgradable daughter card on
interface module
Module Performance
Maximum (mpps)
• Centralized forwarding performance up to
30 mpps per system
• Fully nonblocking when using only two ports
(2 and 4, 1 and 3, 1 and 4, or 2 and 3)
• Up to 98 percent nonblocking with all four
ports active when using dCEF
• Nonblocking at all packet sizes and chassis
configurations on both ports
• Distributed forwarding 30 mpps (line rate for
2 x 10 GE) per slot for interface modules
upgraded with DFCs; sustained system
performance of up to 400 mpps per system
• Distributed forwarding 48 mpps per slot for
interface modules upgraded with DFCs;
sustained system performance of up to
400 mpps per system
Page 4 of 13
Feature
WS-X6704-10GE 4 Port x 10 GE, CEF7201*
WS-X6802-10GE 2 port x 10 GE, dCEF720
Ports, Connector, and Optics
4 ports
2 ports
SC (female)
SC (female)
XENPAKs:
XENPAKs:
• XENPAK-10GB-SR
• XENPAK-10GB-SR
Maximum Port Density
and Chassis
• XENPAK-10GB-LR
• XENPAK-10GB-LR
• XENPAK-10GB-ER
• XENPAK-10GB-ER
• XENPAK-10GB-LX4
• XENPAK-10GB-LX4
• XENPAK-10GB-CX4
• XENPAK-10GB-CX4
• 20 ports (13-slot)
Supervisor Engines Supported
Supervisor Engine 720
Performance Upgrades and
Requirements
dCEF upgrade with Supervisor Engine 720:
DFC3 integrated, used with
• WS-F6700-DFC3BXL
• WS-F6700-DFC3B
• WS-F6700-DFC3A
Fabric Connections
Slot Requirements
QoS Queue Selection Criteria
Dual 20-Gbps serial channel connections to the
Dual 20-Gbps serial channel connections to the
switch fabric of the Supervisor Engine 720
switch fabric of the Supervisor Engine 720
Can occupy any slot in any Cisco Catalyst 6503-
Can occupy any slot in any Cisco Catalyst 6503-
E, 6506, 6506-E, 6509, 6509-E or 6509-NEB-A
E, 6506, 6506-E, 6509, 6509-E, or 6509-NEB-A
chassis; can only occupy slots 9 through 13 in a
chassis; can only occupy slots 9 through 13 in a
Cisco Catalyst 6513 chassis
Cisco Catalyst 6513 chassis
CoS-queue
• CoS-queue
• Differentiated Services Code Point
(DSCP)-queue
• VLAN-queue
Scheduler
Deficit WRR
Deficit WRR and Shaped Round Robin
Transmit Queue Structure**
1p7q8t (CoS to Queue)
• 1p7q8t (CoS to Queue)
• 1p15q8t (VLAN-Q or DSCP-Q)
Receive Queue Structure
1q8t (when using dCEF: 8q8t CoS to Queue)
• 8q8t (CoS to Queue)
• 16q1t (VLAN-Q or DSCP-Q)
Buffer Size
16 MB
256 MB
Jumbo Frame Support
Up to 9216 bytes
Up to 9216 bytes
*For optimal performance, Cisco recommends equipping this module with a DFC.
**Legend: 1p7q8t = one strict priority queue, seven WRR queues, and eight thresholds per WRR queue
Page 5 of 13
Superior Traffic Management and Queuing Characteristics
Cisco Catalyst 6500 Series 10 Gigabit Ethernet modules support multiple queues per port for quality of service. Each port supports Weighted
Random Early Detection (WRED) for congestion avoidance within each queue, and Weighted Round Robin (WRR) for scheduling between queues
and a strict priority queue for voice traffic. Additionally, multiple thresholds can be configured to manage differentiated levels of service.
Ideal for handling mission-critical, bursty, or low-latency traffic such as enterprise resource planning (ERP) or voice applications, these interface
modules, including the CEF720-based WS-X6704-10GE, enable scaling of network performance and intelligent services. These modules also feature
transmit and receive packet buffers and a strict priority transmit queue. Additionally, the dCEF720-based WS-X6802-10GE offers deep packet
buffers and granular queuing (16 queues per port using VLAN-Q or DSCP-Q) making it ideal for service provider deployments, particularly longhaul 10 Gigabit Ethernet transmission.
Cisco EtherChannel Technology Increases Link Resiliency and Provides Scalable Bandwidth Aggregation
Cisco Catalyst 6500 Series modules can aggregate up to eight physical Fast Ethernet, Gigabit Ethernet, or 10 Gigabit Ethernet links into a single
virtual link using the Cisco Port Aggregation Protocol (PAgP) or IEEE 802.3ad technology. This capability provides network managers a reliable
high-speed solution for the campus network backbone.
Cisco Catalyst 6500 Series modules also support multimodule channeling technology, providing even greater resiliency by creating channels
across ports on separate modules in the same chassis. As a result, connectivity is maintained even if one module (and corresponding ports) fails.
This capability is ideal for deployments requiring scalable, flexible bandwidth within the network. Additional benefits of Cisco EtherChannel
capabilities include automatic recovery and redistribution of loads across remaining links; easing management; and making the technology
transparent to network applications.
CISCO CATALYST 6500 SERIES 4-PORT 10 GIGABIT ETHERNET INTERFACE MODULE, CEF720
Designed for distribution to core and data center interconnections in networks, the 4-port CEF720-based 10 Gigabit Ethernet interface modules
deliver highly scalable high-performance 10 Gigabit Ethernet forwarding capabilities with optional fully distributed forwarding. The WS-X670410GE provides higher system port density at an affordable price, encouraging the migration from Gigabit EtherChannel deployments to 10 Gigabit
Ethernet. These modules provide the following operational advantages:
• Centralized Forwarding Architecture—The supervisor’s (Cisco Express Forwarding) engine performs all forwarding decisions; optional
distributed forwarding is supported as an upgrade
• Forwarding Performance—Forwards up to 30 mpps per system (Cisco Express Forwarding) or when equipped with the optional dCEF daughter
card for full local forwarding, can deliver up to 48 mpps sustained throughput per slot with sustained system throughput of up to 400 mpps
When two of four ports (ports 1 and 3, 2 and 4, 2 and 3, or 1 and 4) are used on this interface module, equipped with the distributed
forwarding card, nonblocking performance is achieved. When all four ports are active, these ports are up to 98 percent nonblocking.
• Distributed Forwarding Upgrade Option—Increases system throughput by allowing all forwarding decisions to be locally distributed to the
DFC-equipped interface module; requires a WS-F6700-DFC3 or WS-F6700-DFC3B or WS-F6700-DFC3A and Cisco IOS native mode operation
on the Supervisor Engine 720
• Fabric Connection—Connects through dual 20-Gbps serial-channel connections to fabric on the Supervisor Engine 720 (40 Gbps total per slot,
for 80 Gbps total per slot full duplex)
• Supervisor Engine—Requires the Supervisor Engine 720
• Slot and Chassis Requirements—Can occupy any slot in Cisco Catalyst 6503-E, 6506, 6506-E, 6509, 6509-E or 6509-NEB-A chassis; requires
slots 9 through 13 when used in the Catalyst 6513
• Optics—Supports hot-pluggable XENPAK optical modules (see Table 2 for XENPAKs supported and Table 3 for cables available)
Page 6 of 13
Table 2.
XENPAKs for CEF720 4-port 10 Gigabit Ethernet Module and dCEF720 2-port 10 Gigabit Ethernet Module
Product ID
Transceiver Type
XENPAK-10GB-SR
10GBASE-SR
Wavelength
IEEE
Standard
Maximum Distance/Cable Type
850 nm Serial
802.3ae
• 26 m over 62.5-micron FDDI grade multimode fiber
• 33 m over 62.5-micron 200 MHz*km multimode fiber
• 66 m over 50-micron 400 MHz*km multimode fiber
• 82 m over 50-micron 500 MH*km multimode fiber
• 300 m over 50-micron 2000 MHz*km multimode fiber
XENPAK-10GB-LR
10GBASE-LR
1310 nm Serial
802.3ae
10 km over single multimode fiber
XENPAK-10GB-ER
10GBASE-ER
1550 nm Serial
802.3ae
40 km over single multimode fiber**
XENPAK-10GB-LX4
10GBASE-LX4
WWDM 1310 nm
802.3ae
• 300 m over 62.5-micron FDDI grade multimode fiber
• 240 m over 50-micron 400 MHz km multimode fiber
• 300 m over 50-micron 500 MHz km multimode fiber
XENPAK-10GB-CX4
10GBASE-CX4
Copper
802.3ak
15 m over 8 pair 100-Ohm infiniband cable
*All XENPAKs have SC (female) connectors
**According to the IEEE 802.3ae standard. Requires 5 dB 1550 nm fixed loss attenuator for <20 km; a 5 dB fixed loss attenuator is available as a spare, part number
WS-X6K-5DB-ATT=. To calculate the exact distances that your module will support before installation, see Table 4 and Figure 6. The exact distance supported varies
according to the number of splices and connectors in a single-mode fiber strand.
Table 3.
Cables for 10GBASE-CX4 XENPAK
Product ID
Product Description
CAB-INF-28G-1=
Cisco 1 m CX4 patch cable
CAB-INF-28G-5=
CAB-INF-28G-10=
CAB-INF-26G-15=
CISCO CATALYST 6500 SERIES 2-PORT 10 GIGABIT ETHERNET INTERFACE MODULE, DCEF720
Suited for high-performance distribution and core layers, data centers, Web hosting, storage networking, distributed grid supercomputing
applications, and long-haul 10 Gigabit Ethernet transmission, the 2-port dCEF-based 10 Gigabit Ethernet interface module (Figure 5) makes all
forwarding decisions locally, without supervisor intervention. These interface modules are equipped with large buffers for superior traffic shaping
and feature a large number of queues per port with multiple drop thresholds for enforcement of granular service-level agreements. They provide linerate 10 Gigabit Ethernet forwarding with the following operational advantages:
• Distributed Forwarding Architecture—Uses the dCEF engine and dCEF tables located on the interface module rather than the supervisor to
perform all forwarding decisions locally
• Forwarding Performance—Forwards packets at wire rate, up to 400 mpps per system and 30 mpps per slot
• Distributed Forwarding Features—Includes a DFC3 for distributed bridging, routing, access control lists (ACLs), QoS policy enforcement, and
NetFlow; no upgrade is required
• Fabric Connection—Connects through dual 20-Gbps serial-channel connections to fabric on Supervisor Engine 720 (40 Gbps total per slot, i.e.,
80 Gbps total per slot full duplex)
• Supervisor Engine—Requires Supervisor Engine 720 using Cisco IOS Software; Cisco Catalyst Operating System Software is not compatible
with dCEF distributed forwarding
Page 7 of 13
• Slot Requirements—Can occupy any slot in Cisco Catalyst 6506, 6509, or 6509-NEB-A chassis; the Cisco Catalyst 6513 chassis requires
installation in slots 9 through 13 (the only slots on the chassis with dual fabric connections)
• Optics—Supports hot-pluggable XENPAK optical modules (see Table 2 for XENPAKs supported)
Figure 5.
dCEF720 10 Gigabit Ethernet Optical Module WS-X6802-10GE and XENPAKs
10 Gigabit Ethernet Optics
Cisco Catalyst 6500 Series 10 Gigabit Ethernet modules use IEEE 802.3ae and 802.3ak standards-based 10 Gigabit Ethernet XENPAK optics
(Table 4 and Figure 6).
XENPAK Modules for 2- and 4-Port 10 Gigabit Interface Modules
The WS-X6802-10GE and WS-X6704-10GE support industry XENPAK modular optics, providing both flexibility in station-to-station distances
and investment protection for redeployment options. Each XENPAK supports a single 10 Gigabit Ethernet interface and can be mixed with other
XENPAK optics on the same interface module for custom configurations. See Table 2 for XENPAKs supported on these modules.
Table 4. 10 Gigabit Ethernet Optical Specifications
Product ID
Transceiver Type
Wavelength
XENPAK-GB-SR
10GBASE-SR
840 to 860 nm
XENPAK-GB-LR
10GBASE-LR
XENPAK-10GB-ER
XENPAK-10GB-LX4
10GBASE-ER
10GBASE-LX4
1260 to 1355 nm
1530 to 1565 nm
Transmit Power
Receive Power
Min: -7.3 dBm
Min: -9.9 dBm
Max: -
Max: -1.0 dBm
Min: -8.2 dBm
Min: -14.4 dBm
Max: 0.5 dBm
Max: 0.5 dBm
Min: -4.7 dBm
Min: -15.8 dBm
Max: 4 dBm
Max: -1 dBm
Four lanes:
Min: —
Min: -14.4 dBm per lane*
1269.0 to 1282.4 nm
Max: -0.5 dBm per lane
Max: -0.5 dBm per lane
1293.5 to 1306.9 nm
1318.0 to 1331.4 nm
1342.5 to 1355.9 nm
*OMA sensitivity
Page 8 of 13
Figure 6.
10GBASE-ER Attenuator Management
According to the IEEE 802.3ae standard, the 10GBASE-E channel shall have an attenuation between 5 and 11 dB. If required, an
attenuator can be added to comply with this specification. The ideal channel attenuation is 8 dB.
ORDERING INFORMATION
Table 5 lists the ordering information for Cisco Catalyst 6500 Series 10 Gigabit Ethernet interface modules.
Table 5. Product Numbers for Ordering
Product ID
Product Description
WS-X6802-10GE
Cisco Catalyst 6500 dCEF720 2-port 10 Gigabit Ethernet Module, requires XENPAK
WS-X6704-10GE
Cisco Catalyst 6500 CEF720 4-port 10 Gigabit Ethernet Module, requires XENPAK
WS-F6700-DFC3BXL
Distributed Forwarding Card-3BXL Upgrade for WS-X67xx linecards using WS-SUP720-3BXL
WS-F6700-DFC3B
Distributed Forwarding Card-3B Upgrade for WS-X67xx linecards using WS-SUP720-3B
WS-F6700-DFC3A
Distributed Forwarding Card-3B Upgrade for WS-X67xx linecards using WS-SUP720
XENPAK-10GB-SR
1-port 10GBASE-SR XENPAK, SC connector (multimode fiber)
XENPAK-10GB-LR
1-port 10GBASE-LR XENPAK (single-mode fiber)
XENPAK-10GB-ER
1-port 10GBASE-ER XENPAK (single-mode fiber)
XENPAK-10GB-LX4
1-port 10GBASE-LX4 XENPAK (multimode fiber)
XENPAK-10GB-CX4
1-port 10GBASE-CX4 XENPAK (copper infiniband cable)
CAB-INF-28G-1=
Cisco 1 m CX4 patch cable for XENPAK-10GB-CX4
CAB-INF-28G-5=
CAB-INF-28G-10=
CAB-INF-26G-15=
Page 9 of 13
SPECIFICATIONS
Standard Protocols
• IEEE 802.1d, IEEE 802.1p, IEEE 802.1q, IEEE 802.1s, IEEE 802.1w, IEEE 802.3x, IEEE 802.3ad, IEEE 802.3ae, and IEEE 802.3ak
Physical Specifications
• Occupies one slot in the Cisco Catalyst 6500 Series chassis
• Dimensions (H x W x D): 1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm)
Environmental Conditions
• Operating temperature: 32° to 104° F (0° to 40° C)
• Storage temperature: -40° to 167° F (-40° to 75° C)
• Relative humidity: 10 to 90 percent, noncondensing
• Operating altitude: -60 to 4000 m
Regulatory Compliance
Cisco Catalyst 6500 Series 10 Gigabit Ethernet modules, when installed in a system, comply with the following EMI and safety standards:
• UL 1950
• CSA C22.2 No. 950
• EN 60950
• EN 60825-1
• IEC 60950
• IEC 60825-1
• TS 001
• CE marking
• AS/NZS 3260
• 21CFR1040
• FCC Part 15 (CFR 47) Class A
• VCCI Class A
• EN55022 Class A
• EN55024
• CISPR 22 Class A
• AS/NZS 3548
• ETS 300 386
Network Management
• EHERLIKE-MIB (RFC 1643)
• IF-MIB (RFC 1573)
• Bridge MIB (RFC 1493)
• CISCO-STACK-MIB
• CISCO-VTP-MIB
• CISCO-CDP-MIB
• RMON MIB (RFC 1757)
• CISCO-PAGP-MIB
• CISCO-STP-EXTENSIONS-MIB
Page 10 of 13
• CISCO-VLAN-BRIDGE-MIB
• CISCO-VLAN-MEMBERSHIP-MIB
• ENTITY-MIB (RFC 2037)
• HC-RMON
• RFC1213-MIB (MIB-II)
• SMON-MIB
Station-to-Station Cabling Distance
• 10GBASE-SR: multimode fiber: up to 26 m to 300 m, depending on fiber type
• 10GBASE-LR: single-mode fiber: up to 10 km
• 10GBASE-ER: single-mode fiber: up to 40 km
• 10GBASE-LX4: multimode fiber: up to 300 m
• 10GBASE-CX4: copper infiniband cable: up to 15 m
Power Requirements
• WS-X6704-10GE with DFC3: 389.76W (9.28A @ 42V)
• WS-X6704-10GE without DFC3: 295.26W (7.03A @ 42V)
Go to http://www.cisco.com/go/powercalculator for easy power consumption calculation
Indicators and Interfaces
• Status: green (operational); red (faulty); orange (module booting)
• Link: green (port enabled and connected); orange (port disabled); off (port enabled and not connected)
• XENPAKs: duplex SC (female, single mode)
WS-X6K-5DB-ATT= Specifications
• Operational wavelength: 1550 nm ± 25 nm
• Attenuation: 5 dB ± 1 dB
• Return loss: 50 dB (53 dB typical)
• Connector: SC
• Dimensions: (H x W x D): 9.0 x 12.8 x 37.0 mm
• Operating temperature: -20° to 70° C
• Storage temperature: -40° to 80° C
SERVICE AND SUPPORT
Cisco offers a wide range of services programs to accelerate customer success. These innovative services programs are delivered through a unique
combination of people, processes, tools, and partners, resulting in high levels of customer satisfaction. Cisco services help you to protect your
network investment, optimize network operations, and prepare the network for new applications to extend network intelligence and the power of
your business. For more information about Cisco Services, see Cisco Technical Support Services or Cisco Advanced Services.
FOR MORE INFORMATION
For more information about Cisco Catalyst 6500 Series switch, visit http://www.cisco.com/en/US/products/hw/switches/ps708/index.html
Page 11 of 13
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 526-4100
European Headquarters
Cisco Systems International
BV
Haarlerbergpark
Haarlerbergweg 13-19
1101 CH Amsterdam
The Netherlands
www-europe.cisco.com
Tel: 31 0 20 357 1000
Fax: 31 0 20 357 1100
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
www.cisco.com
Tel: 408 526-7660
Fax: 408 527-0883
Asia Pacific Headquarters
Cisco Systems, Inc.
168 Robinson Road
#28-01 Capital Tower
Singapore 068912
www.cisco.com
Tel: +65 6317 7777
Fax: +65 6317 7799
Cisco Systems has more than 200 offices in the following countries and regions. Addresses, phone numbers, and fax numbers are listed on
the Cisco Web site at www.cisco.com/go/offices.
Argentina • Australia • Austria • Belgium • Brazil • Bulgaria • Canada • Chile • China PRC • Colombia • Costa Rica • Croatia • Cyprus
Czech Republic • Denmark • Dubai, UAE • Finland • France • Germany • Greece • Hong Kong SAR • Hungary • India • Indonesia • Ireland
Israel • Italy • Japan • Korea • Luxembourg • Malaysia • Mexico • The Netherlands • New Zealand • Norway • Peru • Philippines • Poland
Portugal • Puerto Rico • Romania • Russia • Saudi Arabia • Scotland • Singapore • Slovakia • Slovenia • South Africa • Spain • Sweden
Switzerland • Taiwan • Thailand • Turkey • Ukraine • United Kingdom • United States • Venezuela • Vietnam • Zimbabwe
Copyright 2004 Cisco Systems, Inc. All rights reserved. CCIP, CCSP, the Cisco Powered Network mark, Cisco Unity, Follow Me Browsing, FormShare, and StackWise are
trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX,
Catalyst, CCDA, CCDP, CCIE, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, the Cisco IOS logo, Cisco Press, Cisco Systems, Cisco Systems
Capital, the Cisco Systems logo, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherSwitch, Fast Step, GigaStack, Internet Quotient, IOS, IP/TV, iQ
Expertise, the iQ logo, iQ Net Readiness Scorecard, LightStream, Linksys, MGX, MICA, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, PostRouting, Pre-Routing, RateMUX, Registrar, ScriptShare, SlideCast, SMARTnet, StrataView Plus, Stratm, SwitchProbe, TeleRouter, The Fastest Way to Increase Your Internet
Quotient, TransPath, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or Web site are the property of their respective owners. The use of the word partner does not imply a partnership relationship
between Cisco and any other company. (0402R)
204108.24_ETMG_CC_11.04
Printed in the USA
Page 12 of 13
Page 13 of 13

cisco catalyst 6500 series 10 gigabit ethernet modules

Transcription

Similar documents

Cisco - Catalyst Switch Cable, Connector, and AC Power